[PATCH AUTOSEL 5.7 16/25] Revert "i2c: cadence: Fix the hold bit setting"

[PATCH AUTOSEL 5.7 16/25] Revert "i2c: cadence: Fix the hold bit setting"

[Sasha Levin]

From: Raviteja Narayanam <raviteja.narayanam@xilinx.com>

[ Upstream commit 0db9254d6b896b587759e2c844c277fb1a6da5b9 ]

This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9.

There are two issues with "i2c: cadence: Fix the hold bit setting" commit.

1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.

2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.

The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.

The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).

Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i2c/busses/i2c-cadence.c | 9 ++-------
 1 file changed, 2 insertions(+), 7 deletions(-)

diff --git a/drivers/i2c/busses/i2c-cadence.c b/drivers/i2c/busses/i2c-cadence.c
index 89d58f7d2a253..97a0bd6ea31f1 100644
--- a/drivers/i2c/busses/i2c-cadence.c
+++ b/drivers/i2c/busses/i2c-cadence.c
@@ -382,10 +382,8 @@ static void cdns_i2c_mrecv(struct cdns_i2c *id)
 	 * Check for the message size against FIFO depth and set the
 	 * 'hold bus' bit if it is greater than FIFO depth.
 	 */
-	if ((id->recv_count > CDNS_I2C_FIFO_DEPTH)  || id->bus_hold_flag)
+	if (id->recv_count > CDNS_I2C_FIFO_DEPTH)
 		ctrl_reg |= CDNS_I2C_CR_HOLD;
-	else
-		ctrl_reg = ctrl_reg & ~CDNS_I2C_CR_HOLD;
 
 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
 
@@ -442,11 +440,8 @@ static void cdns_i2c_msend(struct cdns_i2c *id)
 	 * Check for the message size against FIFO depth and set the
 	 * 'hold bus' bit if it is greater than FIFO depth.
 	 */
-	if ((id->send_count > CDNS_I2C_FIFO_DEPTH) || id->bus_hold_flag)
+	if (id->send_count > CDNS_I2C_FIFO_DEPTH)
 		ctrl_reg |= CDNS_I2C_CR_HOLD;
-	else
-		ctrl_reg = ctrl_reg & ~CDNS_I2C_CR_HOLD;
-
 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
 
 	/* Clear the interrupts in interrupt status register. */
-- 
2.25.1

[PATCH AUTOSEL 5.7 17/25] i2c: cadence: Clear HOLD bit at correct time in Rx path

[Sasha Levin]

From: Raviteja Narayanam <raviteja.narayanam@xilinx.com>

[ Upstream commit 12d4d9ec5eeecd712c73772e422b6d082e66b046 ]

There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.

This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.

One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).

So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.

Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i2c/busses/i2c-cadence.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/i2c/busses/i2c-cadence.c b/drivers/i2c/busses/i2c-cadence.c
index 97a0bd6ea31f1..1efdabb5adca0 100644
--- a/drivers/i2c/busses/i2c-cadence.c
+++ b/drivers/i2c/busses/i2c-cadence.c
@@ -230,20 +230,21 @@ static irqreturn_t cdns_i2c_isr(int irq, void *ptr)
 		/* Read data if receive data valid is set */
 		while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) &
 		       CDNS_I2C_SR_RXDV) {
-			/*
-			 * Clear hold bit that was set for FIFO control if
-			 * RX data left is less than FIFO depth, unless
-			 * repeated start is selected.
-			 */
-			if ((id->recv_count < CDNS_I2C_FIFO_DEPTH) &&
-			    !id->bus_hold_flag)
-				cdns_i2c_clear_bus_hold(id);
-
 			if (id->recv_count > 0) {
 				*(id->p_recv_buf)++ =
 					cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
 				id->recv_count--;
 				id->curr_recv_count--;
+
+				/*
+				 * Clear hold bit that was set for FIFO control
+				 * if RX data left is less than or equal to
+				 * FIFO DEPTH unless repeated start is selected
+				 */
+				if (id->recv_count <= CDNS_I2C_FIFO_DEPTH &&
+				    !id->bus_hold_flag)
+					cdns_i2c_clear_bus_hold(id);
+
 			} else {
 				dev_err(id->adap.dev.parent,
 					"xfer_size reg rollover. xfer aborted!\n");
-- 
2.25.1