From: Jiawen Wu <jiawenwu@trustnetic.com>
To: netdev@vger.kernel.org, jarkko.nikula@linux.intel.com,
andriy.shevchenko@linux.intel.com,
mika.westerberg@linux.intel.com, jsd@semihalf.com,
Jose.Abreu@synopsys.com, andrew@lunn.ch, hkallweit1@gmail.com,
linux@armlinux.org.uk
Cc: linux-i2c@vger.kernel.org, linux-gpio@vger.kernel.org,
mengyuanlou@net-swift.com, Jiawen Wu <jiawenwu@trustnetic.com>,
Piotr Raczynski <piotr.raczynski@intel.com>
Subject: [PATCH net-next v10 1/9] net: txgbe: Add software nodes to support phylink
Date: Thu, 1 Jun 2023 11:01:32 +0800 [thread overview]
Message-ID: <20230601030140.687493-2-jiawenwu@trustnetic.com> (raw)
In-Reply-To: <20230601030140.687493-1-jiawenwu@trustnetic.com>
Register software nodes for GPIO, I2C, SFP and PHYLINK. Define the
device properties.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
---
drivers/net/ethernet/wangxun/libwx/wx_type.h | 1 +
drivers/net/ethernet/wangxun/txgbe/Makefile | 1 +
.../net/ethernet/wangxun/txgbe/txgbe_main.c | 22 ++++-
.../net/ethernet/wangxun/txgbe/txgbe_phy.c | 89 +++++++++++++++++++
.../net/ethernet/wangxun/txgbe/txgbe_phy.h | 10 +++
.../net/ethernet/wangxun/txgbe/txgbe_type.h | 49 ++++++++++
6 files changed, 171 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
diff --git a/drivers/net/ethernet/wangxun/libwx/wx_type.h b/drivers/net/ethernet/wangxun/libwx/wx_type.h
index cbe7f184b50e..f59066d7375c 100644
--- a/drivers/net/ethernet/wangxun/libwx/wx_type.h
+++ b/drivers/net/ethernet/wangxun/libwx/wx_type.h
@@ -611,6 +611,7 @@ enum wx_isb_idx {
struct wx {
u8 __iomem *hw_addr;
+ void *priv;
struct pci_dev *pdev;
struct net_device *netdev;
struct wx_bus_info bus;
diff --git a/drivers/net/ethernet/wangxun/txgbe/Makefile b/drivers/net/ethernet/wangxun/txgbe/Makefile
index 6db14a2cb2d0..7507f762edfe 100644
--- a/drivers/net/ethernet/wangxun/txgbe/Makefile
+++ b/drivers/net/ethernet/wangxun/txgbe/Makefile
@@ -8,4 +8,5 @@ obj-$(CONFIG_TXGBE) += txgbe.o
txgbe-objs := txgbe_main.o \
txgbe_hw.o \
+ txgbe_phy.o \
txgbe_ethtool.o
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index 5b8a121fb496..e10296abf5b4 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -15,6 +15,7 @@
#include "../libwx/wx_hw.h"
#include "txgbe_type.h"
#include "txgbe_hw.h"
+#include "txgbe_phy.h"
#include "txgbe_ethtool.h"
char txgbe_driver_name[] = "txgbe";
@@ -513,6 +514,7 @@ static int txgbe_probe(struct pci_dev *pdev,
struct net_device *netdev;
int err, expected_gts;
struct wx *wx = NULL;
+ struct txgbe *txgbe;
u16 eeprom_verh = 0, eeprom_verl = 0, offset = 0;
u16 eeprom_cfg_blkh = 0, eeprom_cfg_blkl = 0;
@@ -663,10 +665,23 @@ static int txgbe_probe(struct pci_dev *pdev,
"0x%08x", etrack_id);
}
- err = register_netdev(netdev);
+ txgbe = devm_kzalloc(&pdev->dev, sizeof(*txgbe), GFP_KERNEL);
+ if (!txgbe) {
+ err = -ENOMEM;
+ goto err_release_hw;
+ }
+
+ txgbe->wx = wx;
+ wx->priv = txgbe;
+
+ err = txgbe_init_phy(txgbe);
if (err)
goto err_release_hw;
+ err = register_netdev(netdev);
+ if (err)
+ goto err_remove_phy;
+
pci_set_drvdata(pdev, wx);
netif_tx_stop_all_queues(netdev);
@@ -694,6 +709,8 @@ static int txgbe_probe(struct pci_dev *pdev,
return 0;
+err_remove_phy:
+ txgbe_remove_phy(txgbe);
err_release_hw:
wx_clear_interrupt_scheme(wx);
wx_control_hw(wx, false);
@@ -719,11 +736,14 @@ static int txgbe_probe(struct pci_dev *pdev,
static void txgbe_remove(struct pci_dev *pdev)
{
struct wx *wx = pci_get_drvdata(pdev);
+ struct txgbe *txgbe = wx->priv;
struct net_device *netdev;
netdev = wx->netdev;
unregister_netdev(netdev);
+ txgbe_remove_phy(txgbe);
+
pci_release_selected_regions(pdev,
pci_select_bars(pdev, IORESOURCE_MEM));
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
new file mode 100644
index 000000000000..be4b5ad74a3c
--- /dev/null
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
+
+#include <linux/gpio/property.h>
+#include <linux/i2c.h>
+#include <linux/pci.h>
+
+#include "../libwx/wx_type.h"
+#include "txgbe_type.h"
+#include "txgbe_phy.h"
+
+static int txgbe_swnodes_register(struct txgbe *txgbe)
+{
+ struct txgbe_nodes *nodes = &txgbe->nodes;
+ struct pci_dev *pdev = txgbe->wx->pdev;
+ struct software_node *swnodes;
+ u32 id;
+
+ id = (pdev->bus->number << 8) | pdev->devfn;
+
+ snprintf(nodes->gpio_name, sizeof(nodes->gpio_name), "txgbe_gpio-%x", id);
+ snprintf(nodes->i2c_name, sizeof(nodes->i2c_name), "txgbe_i2c-%x", id);
+ snprintf(nodes->sfp_name, sizeof(nodes->sfp_name), "txgbe_sfp-%x", id);
+ snprintf(nodes->phylink_name, sizeof(nodes->phylink_name), "txgbe_phylink-%x", id);
+
+ swnodes = nodes->swnodes;
+
+ /* GPIO 0: tx fault
+ * GPIO 1: tx disable
+ * GPIO 2: sfp module absent
+ * GPIO 3: rx signal lost
+ * GPIO 4: rate select, 1G(0) 10G(1)
+ * GPIO 5: rate select, 1G(0) 10G(1)
+ */
+ nodes->gpio_props[0] = PROPERTY_ENTRY_STRING("pinctrl-names", "default");
+ swnodes[SWNODE_GPIO] = NODE_PROP(nodes->gpio_name, nodes->gpio_props);
+ nodes->gpio0_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 0, GPIO_ACTIVE_HIGH);
+ nodes->gpio1_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 1, GPIO_ACTIVE_HIGH);
+ nodes->gpio2_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 2, GPIO_ACTIVE_LOW);
+ nodes->gpio3_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 3, GPIO_ACTIVE_HIGH);
+ nodes->gpio4_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 4, GPIO_ACTIVE_HIGH);
+ nodes->gpio5_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 5, GPIO_ACTIVE_HIGH);
+
+ nodes->i2c_props[0] = PROPERTY_ENTRY_STRING("compatible", "snps,designware-i2c");
+ nodes->i2c_props[1] = PROPERTY_ENTRY_BOOL("wx,i2c-snps-model");
+ nodes->i2c_props[2] = PROPERTY_ENTRY_U32("clock-frequency", I2C_MAX_STANDARD_MODE_FREQ);
+ swnodes[SWNODE_I2C] = NODE_PROP(nodes->i2c_name, nodes->i2c_props);
+ nodes->i2c_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_I2C]);
+
+ nodes->sfp_props[0] = PROPERTY_ENTRY_STRING("compatible", "sff,sfp");
+ nodes->sfp_props[1] = PROPERTY_ENTRY_REF_ARRAY("i2c-bus", nodes->i2c_ref);
+ nodes->sfp_props[2] = PROPERTY_ENTRY_REF_ARRAY("tx-fault-gpios", nodes->gpio0_ref);
+ nodes->sfp_props[3] = PROPERTY_ENTRY_REF_ARRAY("tx-disable-gpios", nodes->gpio1_ref);
+ nodes->sfp_props[4] = PROPERTY_ENTRY_REF_ARRAY("mod-def0-gpios", nodes->gpio2_ref);
+ nodes->sfp_props[5] = PROPERTY_ENTRY_REF_ARRAY("los-gpios", nodes->gpio3_ref);
+ nodes->sfp_props[6] = PROPERTY_ENTRY_REF_ARRAY("rate-select1-gpios", nodes->gpio4_ref);
+ nodes->sfp_props[7] = PROPERTY_ENTRY_REF_ARRAY("rate-select0-gpios", nodes->gpio5_ref);
+ swnodes[SWNODE_SFP] = NODE_PROP(nodes->sfp_name, nodes->sfp_props);
+ nodes->sfp_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_SFP]);
+
+ nodes->phylink_props[0] = PROPERTY_ENTRY_STRING("managed", "in-band-status");
+ nodes->phylink_props[1] = PROPERTY_ENTRY_REF_ARRAY("sfp", nodes->sfp_ref);
+ swnodes[SWNODE_PHYLINK] = NODE_PROP(nodes->phylink_name, nodes->phylink_props);
+
+ nodes->group[SWNODE_GPIO] = &swnodes[SWNODE_GPIO];
+ nodes->group[SWNODE_I2C] = &swnodes[SWNODE_I2C];
+ nodes->group[SWNODE_SFP] = &swnodes[SWNODE_SFP];
+ nodes->group[SWNODE_PHYLINK] = &swnodes[SWNODE_PHYLINK];
+
+ return software_node_register_node_group(nodes->group);
+}
+
+int txgbe_init_phy(struct txgbe *txgbe)
+{
+ int ret;
+
+ ret = txgbe_swnodes_register(txgbe);
+ if (ret) {
+ wx_err(txgbe->wx, "failed to register software nodes\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+void txgbe_remove_phy(struct txgbe *txgbe)
+{
+ software_node_unregister_node_group(txgbe->nodes.group);
+}
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
new file mode 100644
index 000000000000..1ab592124986
--- /dev/null
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
+
+#ifndef _TXGBE_PHY_H_
+#define _TXGBE_PHY_H_
+
+int txgbe_init_phy(struct txgbe *txgbe);
+void txgbe_remove_phy(struct txgbe *txgbe);
+
+#endif /* _TXGBE_NODE_H_ */
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 63a1c733718d..5bef0f9df523 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -4,6 +4,8 @@
#ifndef _TXGBE_TYPE_H_
#define _TXGBE_TYPE_H_
+#include <linux/property.h>
+
/* Device IDs */
#define TXGBE_DEV_ID_SP1000 0x1001
#define TXGBE_DEV_ID_WX1820 0x2001
@@ -99,4 +101,51 @@
extern char txgbe_driver_name[];
+static inline struct txgbe *netdev_to_txgbe(struct net_device *netdev)
+{
+ struct wx *wx = netdev_priv(netdev);
+
+ return wx->priv;
+}
+
+#define NODE_PROP(_NAME, _PROP) \
+ (const struct software_node) { \
+ .name = _NAME, \
+ .properties = _PROP, \
+ }
+
+enum txgbe_swnodes {
+ SWNODE_GPIO = 0,
+ SWNODE_I2C,
+ SWNODE_SFP,
+ SWNODE_PHYLINK,
+ SWNODE_MAX
+};
+
+struct txgbe_nodes {
+ char gpio_name[32];
+ char i2c_name[32];
+ char sfp_name[32];
+ char phylink_name[32];
+ struct property_entry gpio_props[1];
+ struct property_entry i2c_props[3];
+ struct property_entry sfp_props[8];
+ struct property_entry phylink_props[2];
+ struct software_node_ref_args i2c_ref[1];
+ struct software_node_ref_args gpio0_ref[1];
+ struct software_node_ref_args gpio1_ref[1];
+ struct software_node_ref_args gpio2_ref[1];
+ struct software_node_ref_args gpio3_ref[1];
+ struct software_node_ref_args gpio4_ref[1];
+ struct software_node_ref_args gpio5_ref[1];
+ struct software_node_ref_args sfp_ref[1];
+ struct software_node swnodes[SWNODE_MAX];
+ const struct software_node *group[SWNODE_MAX + 1];
+};
+
+struct txgbe {
+ struct wx *wx;
+ struct txgbe_nodes nodes;
+};
+
#endif /* _TXGBE_TYPE_H_ */
--
2.27.0
next prev parent reply other threads:[~2023-06-01 3:15 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-01 3:01 [PATCH net-next v10 0/9] TXGBE PHYLINK support Jiawen Wu
2023-06-01 3:01 ` Jiawen Wu [this message]
2023-06-01 3:01 ` [PATCH net-next v10 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC Jiawen Wu
2023-06-01 17:00 ` Andy Shevchenko
2023-06-01 3:01 ` [PATCH net-next v10 3/9] net: txgbe: Register fixed rate clock Jiawen Wu
2023-06-01 3:01 ` [PATCH net-next v10 4/9] net: txgbe: Register I2C platform device Jiawen Wu
2023-06-01 17:04 ` Andy Shevchenko
2023-06-01 3:01 ` [PATCH net-next v10 5/9] net: txgbe: Add SFP module identify Jiawen Wu
2023-06-01 3:01 ` [PATCH net-next v10 6/9] net: txgbe: Support GPIO to SFP socket Jiawen Wu
2023-06-01 17:07 ` Andy Shevchenko
2023-06-01 3:01 ` [PATCH net-next v10 7/9] net: pcs: Add 10GBASE-R mode for Synopsys Designware XPCS Jiawen Wu
2023-06-01 3:01 ` [PATCH net-next v10 8/9] net: txgbe: Implement phylink pcs Jiawen Wu
2023-06-01 3:01 ` [PATCH net-next v10 9/9] net: txgbe: Support phylink MAC layer Jiawen Wu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230601030140.687493-2-jiawenwu@trustnetic.com \
--to=jiawenwu@trustnetic.com \
--cc=Jose.Abreu@synopsys.com \
--cc=andrew@lunn.ch \
--cc=andriy.shevchenko@linux.intel.com \
--cc=hkallweit1@gmail.com \
--cc=jarkko.nikula@linux.intel.com \
--cc=jsd@semihalf.com \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mengyuanlou@net-swift.com \
--cc=mika.westerberg@linux.intel.com \
--cc=netdev@vger.kernel.org \
--cc=piotr.raczynski@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).