From: "Przemysław Gaj" <pgaj@cadence.com>
To: Vitor Soares <Vitor.Soares@synopsys.com>
Cc: "linux-i3c@lists.infradead.org" <linux-i3c@lists.infradead.org>,
"rafalc@cadence.com" <rafalc@cadence.com>,
"bbrezillon@kernel.org" <bbrezillon@kernel.org>
Subject: Re: [PATCH v4 2/6] i3c: master: pre-reserve boardinfo->init_dyn_addr when available
Date: Wed, 11 Dec 2019 09:51:47 +0100 [thread overview]
Message-ID: <20191211085146.GA10780@global.cadence.com> (raw)
In-Reply-To: <CH2PR12MB4216FBF6BA2155A47C76D180AE5B0@CH2PR12MB4216.namprd12.prod.outlook.com>
Hi Vitor,
The 12/10/2019 15:24, Vitor Soares wrote:
>
> Hi Przemysław,
>
> From: Przemysław Gaj <pgaj@cadence.com>
> Date: Tue, Dec 10, 2019 at 10:14:58
>
> > It may be the case that SETDASA fails for some reason. Reserve
> > ->init_dyn_addr when it's defined to prevent assigning this address
> > to another slave device. This way when device shows up we don't
> > have to re-assign addresses.
> >
> > Signed-off-by: Przemysław Gaj <pgaj@cadence.com>
> > ---
> > drivers/i3c/master.c | 8 +++++++-
> > 1 file changed, 7 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/i3c/master.c b/drivers/i3c/master.c
> > index 5c06c41e6660..fab6e0609fca 100755
> > --- a/drivers/i3c/master.c
> > +++ b/drivers/i3c/master.c
> > @@ -1263,7 +1263,8 @@ static void i3c_master_put_i3c_addrs(struct i3c_dev_desc *dev)
> > I3C_ADDR_SLOT_FREE);
> >
> > if (dev->boardinfo && dev->boardinfo->init_dyn_addr)
> > - i3c_bus_set_addr_slot_status(&master->bus, dev->info.dyn_addr,
> > + i3c_bus_set_addr_slot_status(&master->bus,
> > + dev->boardinfo->init_dyn_addr,
> > I3C_ADDR_SLOT_FREE);
> > }
> >
> > @@ -1675,6 +1676,11 @@ static int i3c_master_bus_init(struct i3c_master_controller *master)
> > ret = -EBUSY;
> > goto err_detach_devs;
> > }
> > +
> > + /* Reserve the slot. */
> > + i3c_bus_set_addr_slot_status(&master->bus,
> > + i3cboardinfo->init_dyn_addr,
> > + I3C_ADDR_SLOT_I3C_DEV);
> > }
> >
> > i3cdev = i3c_master_alloc_i3c_dev(master, &info);
> > --
> > 2.14.0
>
> In my experience we should pre-reserve all DT DA entries and not use them
> during the ENTDAA for safety reasons.
> That would be one of my next steps in this patch series.
Actually, I reserve DT DA address above. The only thing I will rework, I
won't free up the address. That will be documented in the code.
We can rework it later if really needed.
>
> Best regards,
> Vitor Soares
>
--
--
Regards,
Przemek
_______________________________________________
linux-i3c mailing list
linux-i3c@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-i3c
next prev parent reply other threads:[~2019-12-11 8:52 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-10 10:14 [PATCH v4 0/6] I3C device addresing adjustments Przemysław Gaj
2019-12-10 10:14 ` [PATCH v4 1/6] i3c: master: make sure ->boardinfo is initialized in add_i3c_dev_locked() Przemysław Gaj
2019-12-10 10:14 ` [PATCH v4 2/6] i3c: master: pre-reserve boardinfo->init_dyn_addr when available Przemysław Gaj
2019-12-10 13:29 ` Boris Brezillon
2019-12-10 15:24 ` Vitor Soares
2019-12-11 8:51 ` Przemysław Gaj [this message]
2019-12-10 10:14 ` [PATCH v4 3/6] i3c: master: make sure the PID is set before registering the device Przemysław Gaj
2019-12-10 10:15 ` [PATCH v4 4/6] dt-bindings: i3c: Make 'assigned-address' valid if static address == 0 Przemysław Gaj
2019-12-10 10:15 ` [PATCH v4 5/6] dt-bindings: i3c: add a note for no guarantee of 'assigned-address' use Przemysław Gaj
2019-12-10 10:15 ` [PATCH v4 6/6] i3c: master: dw: reattach device on first available location of address table Przemysław Gaj
2019-12-10 14:40 ` Vitor Soares
2019-12-10 14:43 ` Przemysław Gaj
2019-12-10 14:52 ` Boris Brezillon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191211085146.GA10780@global.cadence.com \
--to=pgaj@cadence.com \
--cc=Vitor.Soares@synopsys.com \
--cc=bbrezillon@kernel.org \
--cc=linux-i3c@lists.infradead.org \
--cc=rafalc@cadence.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).