Re: [PATCH v4 1/6] i3c: add addr and lvr to i2c_dev_desc structure

[vitor <vitor.soares@synopsys.com>]

Hi,


On 01/04/19 20:24, Boris Brezillon wrote:
> On Mon, 1 Apr 2019 19:48:45 +0100
> vitor <vitor.soares@synopsys.com> wrote:
>
>> Hi,
>>
>> On 01/04/19 19:31, Boris Brezillon wrote:
>>> On Mon, 1 Apr 2019 19:17:03 +0100
>>> vitor <vitor.soares@synopsys.com> wrote:
>>>  
>>>> Hi,
>>>>
>>>> On 30/03/19 14:36, Boris Brezillon wrote:  
>>>>> On Sun, 10 Mar 2019 13:58:38 +0000
>>>>> Przemyslaw Gaj <pgaj@cadence.com> wrote:
>>>>>    
>>>>>> I need to store address and lvr value for I2C devices without static definition
>>>>>> in DT. This allows secondary master to transmit DEFSLVS command properly.
>>>>>>
>>>>>> Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
>>>>>> ---
>>>>>>  include/linux/i3c/master.h | 5 +++++
>>>>>>  1 file changed, 5 insertions(+)
>>>>>>
>>>>>> diff --git a/include/linux/i3c/master.h b/include/linux/i3c/master.h
>>>>>> index eca8337..3c27d9f 100644
>>>>>> --- a/include/linux/i3c/master.h
>>>>>> +++ b/include/linux/i3c/master.h
>>>>>> @@ -71,6 +71,9 @@ struct i2c_dev_boardinfo {
>>>>>>   * @common: common part of the I2C device descriptor
>>>>>>   * @boardinfo: pointer to the boardinfo attached to this I2C device
>>>>>>   * @dev: I2C device object registered to the I2C framework
>>>>>> + * @addr: I2C device address
>>>>>> + * @lvr: LVR (Legacy Virtual Register) needed by the I3C core to know about
>>>>>> + *	 the I2C device limitations
>>>>>>   *
>>>>>>   * Each I2C device connected on the bus will have an i2c_dev_desc.
>>>>>>   * This object is created by the core and later attached to the controller
>>>>>> @@ -84,6 +87,8 @@ struct i2c_dev_desc {
>>>>>>  	struct i3c_i2c_dev_desc common;
>>>>>>  	const struct i2c_dev_boardinfo *boardinfo;
>>>>>>  	struct i2c_client *dev;
>>>>>> +	u16 addr;
>>>>>> +	u8 lvr;    
>>>>> You also need to remove lvr from i2c_dev_boardinfo and adjust the code
>>>>> to use i2c_dev_desc->addr and i2c_dev_desc->lvr in this patch, not in
>>>>> patch 3.
>>>>>    
>>>> Why can't we keep the lvr and addr in i2c_dev_boardinfo and need this information on i2c_dev_desc?  
>>> Because i2c_dev_boardinfo is extracted from the DT and the secondary
>>> slaves does not necessarily have this description. The idea is to keep
>>> reserving the address slot for the I2C device even if we don't expose
>>> it to the upper layers.  
>> So you are using i2c_dev_boardinfo just for DT devices?
> All devices that are described in some way, can be through DT, ACPI or
> board-file desc (only DT is supported right now, but we can easily add
> support for other formats).

We can drop i2c_dev_boardinfo.

>
>> Because at end we need to register the new i2c devs.
> No, only those that have a valid description, because there's nothing
> you can expose if you only have the address and LVR values. You at
> least need to know which driver this dev should be attached to
> (compatible string in your DT) and most drivers also need extra
> information (basically all the DT props that are described a the DT
> binding).

In any case the HC need to know the bus mode, how is this done?

_______________________________________________
linux-i3c mailing list
linux-i3c@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-i3c