From: Guenter Roeck <linux@roeck-us.net>
To: Linus Walleij <linus.walleij@linaro.org>,
Gabriel C <nix.or.die@gmail.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
linux-hwmon@vger.kernel.org, Jean Delvare <jdelvare@suse.com>,
Bart Van Assche <bvanassche@acm.org>,
Linux Doc Mailing List <linux-doc@vger.kernel.org>,
LKML <linux-kernel@vger.kernel.org>,
linux-scsi <linux-scsi@vger.kernel.org>,
"open list:LIBATA SUBSYSTEM (Serial and Parallel ATA drivers)"
<linux-ide@vger.kernel.org>, Chris Healy <cphealy@gmail.com>
Subject: Re: [PATCH v2] hwmon: Driver for temperature sensors on SATA drives
Date: Sun, 12 Jan 2020 05:07:17 -0800 [thread overview]
Message-ID: <e3caa946-b8f2-75c7-4bcb-69ad198de472@roeck-us.net> (raw)
In-Reply-To: <CACRpkdayHFmdz4nAMaXR07Hcy=dLLGnnU8PkFhwQKuDTLnvOSw@mail.gmail.com>
On 1/12/20 4:07 AM, Linus Walleij wrote:
> On Sun, Jan 12, 2020 at 1:03 PM Gabriel C <nix.or.die@gmail.com> wrote:
>> Am So., 12. Jan. 2020 um 12:22 Uhr schrieb Linus Walleij
>> <linus.walleij@linaro.org>:
>>>
>>> On Sun, Jan 12, 2020 at 12:18 PM Gabriel C <nix.or.die@gmail.com> wrote:
>>>
>>>> What I've noticed however is the nvme temperature low/high values on
>>>> the Sensors X are strange here.
>>> (...)
>>>> Sensor 1: +27.9°C (low = -273.1°C, high = +65261.8°C)
>>>> Sensor 2: +29.9°C (low = -273.1°C, high = +65261.8°C)
>>> (...)
>>>> Sensor 1: +23.9°C (low = -273.1°C, high = +65261.8°C)
>>>> Sensor 2: +25.9°C (low = -273.1°C, high = +65261.8°C)
>>>
>>> That doesn't look strange to me. It seems like reasonable defaults
>>> from the firmware if either it doesn't really log the min/max temperatures
>>> or hasn't been through a cycle of updating these yet. Just set both
>>> to absolute min/max temperatures possible.
>>
>> Ok I'll check that.
>>
>> Do you mean by setting the temperatures to use a lmsensors config?
>> Or is there a way to set these with a nvme command?
>
> Not that I know of.
>
> The min/max are the minumum and maximum temperatures the
> device has experienced during this power-on cycle.
>
No, that would be lowest/highest. The above are (or should be) per-sensor
setpoints. The default for those is typically the absolute minimum /
maximum of the supported range.
Some SATA drives report the lowest/highest temperatures experienced
since power cycle, like here.
drivetemp-scsi-5-0
Adapter: SCSI adapter
temp1: +23.0°C (low = +0.0°C, high = +60.0°C)
(crit low = -41.0°C, crit = +85.0°C)
(lowest = +20.0°C, highest = +31.0°C)
Guenter
next prev parent reply other threads:[~2020-01-12 13:07 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-15 17:45 [PATCH v2 0/1] Summary: hwmon driver for temperature sensors on SATA drives Guenter Roeck
2019-12-15 17:45 ` [PATCH v2] hwmon: Driver " Guenter Roeck
2019-12-19 0:15 ` Martin K. Petersen
2019-12-19 0:32 ` Guenter Roeck
2020-01-07 4:10 ` Martin K. Petersen
2020-01-07 13:00 ` Guenter Roeck
2020-01-08 1:29 ` Martin K. Petersen
2020-01-08 15:32 ` Guenter Roeck
2019-12-19 7:37 ` Guenter Roeck
2020-01-01 17:46 ` Guenter Roeck
2020-01-03 3:06 ` Martin K. Petersen
2020-01-08 1:12 ` Martin K. Petersen
2020-01-08 15:33 ` Guenter Roeck
2020-01-11 20:22 ` Guenter Roeck
2020-01-12 11:17 ` Gabriel C
2020-01-12 11:21 ` Linus Walleij
2020-01-12 12:02 ` Gabriel C
2020-01-12 12:07 ` Linus Walleij
2020-01-12 13:07 ` Guenter Roeck [this message]
2020-01-12 13:45 ` Gabriel C
2020-01-12 15:26 ` Guenter Roeck
2020-01-12 18:37 ` Gabriel C
2020-01-12 20:08 ` Guenter Roeck
2020-01-12 22:26 ` Gabriel C
2020-01-14 3:03 ` Martin K. Petersen
2020-01-14 5:20 ` Guenter Roeck
2020-01-16 4:12 ` Martin K. Petersen
2020-01-16 5:09 ` Guenter Roeck
2020-01-16 17:47 ` Guenter Roeck
2020-01-17 1:43 ` Martin K. Petersen
2020-01-17 3:53 ` Guenter Roeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e3caa946-b8f2-75c7-4bcb-69ad198de472@roeck-us.net \
--to=linux@roeck-us.net \
--cc=bvanassche@acm.org \
--cc=cphealy@gmail.com \
--cc=jdelvare@suse.com \
--cc=linus.walleij@linaro.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=martin.petersen@oracle.com \
--cc=nix.or.die@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).