Linux-IIO Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 0/3] add support for PMS7003 PM sensor
@ 2019-01-06 17:16 Tomasz Duszynski
  2019-01-06 17:16 ` [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor Tomasz Duszynski
                   ` (2 more replies)
  0 siblings, 3 replies; 11+ messages in thread
From: Tomasz Duszynski @ 2019-01-06 17:16 UTC (permalink / raw)
  To: linux-iio; +Cc: linux-kernel, devicetree, Tomasz Duszynski

This patch series adds support for Plantower PMS7003 PM matter sensor.

Unfortunately datasheet is not available for download from the Plantower
website so one needs to find it elsewhere, for instance here:

https://download.kamami.com/p564008-p564008-PMS7003%20series%20data%20manua_English_V2.5.pdf

Tomasz Duszynski (3):
  iio: chemical: add support for Plantower PMS7003 sensor
  dt-bindings: add Plantower to the vendor prefixes
  dt-bindings: iio: chemical: pms7003: add device tree support

 .../iio/chemical/plantower,pms7003.txt        |  14 +
 .../devicetree/bindings/vendor-prefixes.txt   |   1 +
 drivers/iio/chemical/Kconfig                  |  10 +
 drivers/iio/chemical/Makefile                 |   1 +
 drivers/iio/chemical/pms7003.c                | 411 ++++++++++++++++++
 5 files changed, 437 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
 create mode 100644 drivers/iio/chemical/pms7003.c

--
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor
  2019-01-06 17:16 [PATCH 0/3] add support for PMS7003 PM sensor Tomasz Duszynski
@ 2019-01-06 17:16 ` Tomasz Duszynski
  2019-01-07 15:35   ` Johan Hovold
  2019-01-12 17:48   ` Jonathan Cameron
  2019-01-06 17:16 ` [PATCH 2/3] dt-bindings: add Plantower to the vendor prefixes Tomasz Duszynski
  2019-01-06 17:16 ` [PATCH 3/3] dt-bindings: iio: chemical: pms7003: add device tree support Tomasz Duszynski
  2 siblings, 2 replies; 11+ messages in thread
From: Tomasz Duszynski @ 2019-01-06 17:16 UTC (permalink / raw)
  To: linux-iio; +Cc: linux-kernel, devicetree, Tomasz Duszynski

Add support for Plantower PMS7003 particulate matter sensor.

Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
---
 drivers/iio/chemical/Kconfig   |  10 +
 drivers/iio/chemical/Makefile  |   1 +
 drivers/iio/chemical/pms7003.c | 411 +++++++++++++++++++++++++++++++++
 3 files changed, 422 insertions(+)
 create mode 100644 drivers/iio/chemical/pms7003.c

diff --git a/drivers/iio/chemical/Kconfig b/drivers/iio/chemical/Kconfig
index 57832b4360e9..d5d146e9e372 100644
--- a/drivers/iio/chemical/Kconfig
+++ b/drivers/iio/chemical/Kconfig
@@ -61,6 +61,16 @@ config IAQCORE
 	  iAQ-Core Continuous/Pulsed VOC (Volatile Organic Compounds)
 	  sensors
 
+config PMS7003
+	tristate "Plantower PMS7003 particulate matter sensor"
+	depends on SERIAL_DEV_BUS
+	help
+	  Say Y here to build support for the Plantower PMS7003 particulate
+	  matter sensor.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called pms7003.
+
 config SPS30
 	tristate "SPS30 particulate matter sensor"
 	depends on I2C
diff --git a/drivers/iio/chemical/Makefile b/drivers/iio/chemical/Makefile
index 65bf0f89c0e4..f5d1365acb49 100644
--- a/drivers/iio/chemical/Makefile
+++ b/drivers/iio/chemical/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_BME680_I2C) += bme680_i2c.o
 obj-$(CONFIG_BME680_SPI) += bme680_spi.o
 obj-$(CONFIG_CCS811)		+= ccs811.o
 obj-$(CONFIG_IAQCORE)		+= ams-iaq-core.o
+obj-$(CONFIG_PMS7003) += pms7003.o
 obj-$(CONFIG_SENSIRION_SGP30)	+= sgp30.o
 obj-$(CONFIG_SPS30) += sps30.o
 obj-$(CONFIG_VZ89X)		+= vz89x.o
diff --git a/drivers/iio/chemical/pms7003.c b/drivers/iio/chemical/pms7003.c
new file mode 100644
index 000000000000..bc8a4fbdf641
--- /dev/null
+++ b/drivers/iio/chemical/pms7003.c
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Plantower PMS7003 particulate matter sensor driver
+ *
+ * Copyright (c) Tomasz Duszynski <tduszyns@gmail.com>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <asm/unaligned.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/serdev.h>
+
+#define PMS7003_DRIVER_NAME "pms7003"
+
+#define PMS7003_MAGIC_MSB 0x42
+#define PMS7003_MAGIC_LSB 0x4d
+/* last 2 data bytes hold frame checksum */
+#define PMS7003_MAX_DATA_LENGTH 28
+#define PMS7003_CHECKSUM_LENGTH 2
+#define PMS7003_PM10_OFFSET 10
+#define PMS7003_PM2P5_OFFSET 8
+#define PMS7003_PM1_OFFSET 6
+
+#define PMS7003_TIMEOUT msecs_to_jiffies(6000)
+#define PMS7003_CMD_LENGTH 7
+#define PMS7003_PM_MAX 1000
+#define PMS7003_PM_MIN 0
+
+enum {
+	PM1,
+	PM2P5,
+	PM10,
+};
+
+enum {
+	CMD_WAKEUP,
+	CMD_ENTER_PASSIVE_MODE,
+	CMD_READ_PASSIVE,
+	CMD_SLEEP,
+};
+
+enum {
+	STATE_MAGIC_MSB,
+	STATE_MAGIC_LSB,
+	STATE_LENGTH_MSB,
+	STATE_LENGTH_LSB,
+	STATE_DATA,
+};
+
+struct pms7003_frame {
+	u8 data[PMS7003_MAX_DATA_LENGTH];
+	u16 expected_length;
+	u16 length;
+	int state;
+};
+
+struct pms7003_state {
+	struct serdev_device *serdev;
+	struct pms7003_frame frame;
+	struct completion frame_ready;
+	struct mutex lock; /* must be held whenever state gets touched */
+};
+
+static u16 pms7003_calc_checksum(const u8 *data, int size)
+{
+	u16 checksum = 0;
+
+	while (size--)
+		checksum += data[size];
+
+	return checksum;
+}
+
+static int pms7003_do_cmd(struct pms7003_state *state, u8 cmd)
+{
+	/*
+	 * commands have following format:
+	 *
+	 * +------+------+-----+------+-----+-----------+-----------+
+	 * | 0x42 | 0x4d | cmd | 0x00 | arg | cksum msb | cksum lsb |
+	 * +------+------+-----+------+-----+-----------+-----------+
+	 */
+	u8 tmp[PMS7003_CMD_LENGTH] = { PMS7003_MAGIC_MSB, PMS7003_MAGIC_LSB };
+	int ret, n = 2;
+	u16 checksum;
+
+	switch (cmd) {
+	case CMD_WAKEUP:
+		tmp[n++] = 0xe4;
+		tmp[n++] = 0x00;
+		tmp[n++] = 0x01;
+		break;
+	case CMD_ENTER_PASSIVE_MODE:
+		tmp[n++] = 0xe1;
+		tmp[n++] = 0x00;
+		tmp[n++] = 0x00;
+		break;
+	case CMD_READ_PASSIVE:
+		tmp[n++] = 0xe2;
+		tmp[n++] = 0x00;
+		tmp[n++] = 0x00;
+		break;
+	case CMD_SLEEP:
+		tmp[n++] = 0xe4;
+		tmp[n++] = 0x00;
+		tmp[n++] = 0x00;
+		break;
+	}
+
+	checksum = pms7003_calc_checksum(tmp, n);
+	put_unaligned_be16(checksum, tmp + n);
+	n += PMS7003_CHECKSUM_LENGTH;
+
+	ret = serdev_device_write(state->serdev, tmp, n, PMS7003_TIMEOUT);
+	if (ret)
+		return ret;
+
+	ret = wait_for_completion_interruptible_timeout(&state->frame_ready,
+							PMS7003_TIMEOUT);
+	if (!ret)
+		ret = -ETIMEDOUT;
+
+	return ret < 0 ? ret : 0;
+}
+
+static u16 pms7003_get_pm(struct pms7003_frame *frame, int offset)
+{
+	return clamp_val(get_unaligned_be16(frame->data + offset),
+			 PMS7003_PM_MIN, PMS7003_PM_MAX);
+}
+
+static irqreturn_t pms7003_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct pms7003_state *state = iio_priv(indio_dev);
+	struct pms7003_frame *frame = &state->frame;
+	u16 data[3 + 1 + 4]; /* PM1, PM2P5, PM10, padding, timestamp */
+	int ret;
+
+	mutex_lock(&state->lock);
+	ret = pms7003_do_cmd(state, CMD_READ_PASSIVE);
+	if (ret) {
+		mutex_unlock(&state->lock);
+		goto err;
+	}
+
+	data[PM1] = pms7003_get_pm(frame, PMS7003_PM1_OFFSET);
+	data[PM2P5] = pms7003_get_pm(frame, PMS7003_PM2P5_OFFSET);
+	data[PM10] = pms7003_get_pm(frame, PMS7003_PM10_OFFSET);
+	mutex_unlock(&state->lock);
+
+	iio_push_to_buffers_with_timestamp(indio_dev, data,
+					   iio_get_time_ns(indio_dev));
+err:
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
+static int pms7003_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int *val, int *val2, long mask)
+{
+	struct pms7003_state *state = iio_priv(indio_dev);
+	struct pms7003_frame *frame = &state->frame;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		switch (chan->type) {
+		case IIO_MASSCONCENTRATION:
+			mutex_lock(&state->lock);
+			ret = pms7003_do_cmd(state, CMD_READ_PASSIVE);
+			if (ret) {
+				mutex_unlock(&state->lock);
+				return ret;
+			}
+
+			switch (chan->channel2) {
+			case IIO_MOD_PM1:
+				*val = pms7003_get_pm(frame,
+						      PMS7003_PM1_OFFSET);
+				break;
+			case IIO_MOD_PM2P5:
+				*val = pms7003_get_pm(frame,
+						      PMS7003_PM2P5_OFFSET);
+				break;
+			case IIO_MOD_PM10:
+				*val = pms7003_get_pm(frame,
+						      PMS7003_PM10_OFFSET);
+				break;
+			}
+			mutex_unlock(&state->lock);
+
+			return IIO_VAL_INT;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return -EINVAL;
+}
+
+
+static const struct iio_info pms7003_info = {
+	.read_raw = pms7003_read_raw,
+};
+
+#define PMS7003_CHAN(_index, _mod) { \
+	.type = IIO_MASSCONCENTRATION, \
+	.modified = 1, \
+	.channel2 = IIO_MOD_ ## _mod, \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), \
+	.scan_index = _index, \
+	.scan_type = { \
+		.sign = 'u', \
+		.realbits = 10, \
+		.storagebits = 16, \
+		.endianness = IIO_CPU, \
+	}, \
+}
+
+static const struct iio_chan_spec pms7003_channels[] = {
+	PMS7003_CHAN(0, PM1),
+	PMS7003_CHAN(1, PM2P5),
+	PMS7003_CHAN(2, PM10),
+	IIO_CHAN_SOFT_TIMESTAMP(3),
+};
+
+static int pms7003_frame_okay(struct pms7003_frame *frame)
+{
+	int offset = frame->length - PMS7003_CHECKSUM_LENGTH;
+	u16 checksum = PMS7003_MAGIC_MSB + PMS7003_MAGIC_LSB +
+		       (frame->length >> 8) + (u8)frame->length +
+		       pms7003_calc_checksum(frame->data, offset);
+
+	return checksum == get_unaligned_be16(frame->data + offset);
+}
+
+static int pms7003_update_frame(struct pms7003_frame *frame, u8 byte)
+{
+	switch (frame->state) {
+	case STATE_MAGIC_MSB:
+		if (byte != PMS7003_MAGIC_MSB)
+			return 1;
+		frame->state = STATE_MAGIC_LSB;
+		frame->length = 0;
+		return 1;
+	case STATE_MAGIC_LSB:
+		if (byte != PMS7003_MAGIC_LSB) {
+			frame->state = STATE_MAGIC_MSB;
+			return 1;
+		}
+		frame->state = STATE_LENGTH_MSB;
+		return 1;
+	case STATE_LENGTH_MSB:
+		frame->expected_length = (u16)byte << 8;
+		frame->state = STATE_LENGTH_LSB;
+		return 1;
+	case STATE_LENGTH_LSB:
+		frame->expected_length |= byte;
+		frame->state = STATE_DATA;
+		return 1;
+	case STATE_DATA:
+		if (frame->length > PMS7003_MAX_DATA_LENGTH) {
+			frame->state = STATE_MAGIC_MSB;
+			return 1;
+		}
+
+		frame->data[frame->length++] = byte;
+
+		if (frame->length != frame->expected_length)
+			return 1;
+
+		if (!pms7003_frame_okay(frame)) {
+			frame->state = STATE_MAGIC_MSB;
+			return 1;
+		}
+
+		frame->state = STATE_MAGIC_MSB;
+		break;
+	}
+
+	return 0;
+}
+
+static int pms7003_receive_buf(struct serdev_device *serdev,
+			       const unsigned char *buf, size_t size)
+{
+	struct iio_dev *indio_dev = serdev_device_get_drvdata(serdev);
+	struct pms7003_state *state = iio_priv(indio_dev);
+	struct pms7003_frame *frame = &state->frame;
+	int i, ret;
+
+	for (i = 0; i < size; i++) {
+		ret = pms7003_update_frame(frame, buf[i]);
+		if (ret)
+			continue;
+
+		complete(&state->frame_ready);
+		return i + 1;
+	}
+
+	return size;
+}
+
+static const struct serdev_device_ops pms7003_serdev_ops = {
+	.receive_buf = pms7003_receive_buf,
+	.write_wakeup = serdev_device_write_wakeup,
+};
+
+static void pms7003_stop(void *data)
+{
+	struct pms7003_state *state = data;
+
+	pms7003_do_cmd(state, CMD_SLEEP);
+}
+
+static const unsigned long pms7003_scan_masks[] = { 0x07, 0x00 };
+
+static int pms7003_probe(struct serdev_device *serdev)
+{
+	struct pms7003_state *state;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&serdev->dev, sizeof(*state));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	state = iio_priv(indio_dev);
+	serdev_device_set_drvdata(serdev, indio_dev);
+	state->serdev = serdev;
+	indio_dev->dev.parent = &serdev->dev;
+	indio_dev->info = &pms7003_info;
+	indio_dev->name = PMS7003_DRIVER_NAME;
+	indio_dev->channels = pms7003_channels,
+	indio_dev->num_channels = ARRAY_SIZE(pms7003_channels);
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->available_scan_masks = pms7003_scan_masks;
+
+	mutex_init(&state->lock);
+	init_completion(&state->frame_ready);
+
+	serdev_device_set_client_ops(serdev, &pms7003_serdev_ops);
+	ret = devm_serdev_device_open(&serdev->dev, serdev);
+	if (ret)
+		return ret;
+
+	serdev_device_set_baudrate(serdev, 9600);
+	serdev_device_set_flow_control(serdev, false);
+
+	ret = serdev_device_set_parity(serdev, SERDEV_PARITY_NONE);
+	if (ret)
+		return ret;
+
+	ret = pms7003_do_cmd(state, CMD_WAKEUP);
+	if (ret) {
+		dev_err(&serdev->dev, "failed to wakeup sensor\n");
+		return ret;
+	}
+
+	ret = pms7003_do_cmd(state, CMD_ENTER_PASSIVE_MODE);
+	if (ret) {
+		dev_err(&serdev->dev, "failed to enter passive mode\n");
+		return ret;
+	}
+
+	ret = devm_add_action_or_reset(&serdev->dev, pms7003_stop, state);
+	if (ret)
+		return ret;
+
+	ret = devm_iio_triggered_buffer_setup(&serdev->dev, indio_dev, NULL,
+					      pms7003_trigger_handler, NULL);
+	if (ret)
+		return ret;
+
+	return devm_iio_device_register(&serdev->dev, indio_dev);
+}
+
+static const struct of_device_id pms7003_of_match[] = {
+	{ .compatible = "plantower,pms7003" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, pms7003_of_match);
+
+static struct serdev_device_driver pms7003_driver = {
+	.driver = {
+		.name = PMS7003_DRIVER_NAME,
+		.of_match_table = pms7003_of_match,
+	},
+	.probe = pms7003_probe,
+};
+module_serdev_device_driver(pms7003_driver);
+
+MODULE_AUTHOR("Tomasz Duszynski <tduszyns@gmail.com>");
+MODULE_DESCRIPTION("Plantower PMS7003 particulate matter sensor driver");
+MODULE_LICENSE("GPL v2");
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 2/3] dt-bindings: add Plantower to the vendor prefixes
  2019-01-06 17:16 [PATCH 0/3] add support for PMS7003 PM sensor Tomasz Duszynski
  2019-01-06 17:16 ` [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor Tomasz Duszynski
@ 2019-01-06 17:16 ` Tomasz Duszynski
  2019-01-11 22:12   ` Rob Herring
  2019-01-06 17:16 ` [PATCH 3/3] dt-bindings: iio: chemical: pms7003: add device tree support Tomasz Duszynski
  2 siblings, 1 reply; 11+ messages in thread
From: Tomasz Duszynski @ 2019-01-06 17:16 UTC (permalink / raw)
  To: linux-iio; +Cc: linux-kernel, devicetree, Tomasz Duszynski

Add Plantower to the vendor prefixes.

Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 3cfe0c8b8250..fa391a650f3a 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -300,6 +300,7 @@ phytec	PHYTEC Messtechnik GmbH
 picochip	Picochip Ltd
 pine64	Pine64
 pixcir  PIXCIR MICROELECTRONICS Co., Ltd
+plantower Plantower Co., Ltd
 plathome	Plat'Home Co., Ltd.
 plda	PLDA
 plx	Broadcom Corporation (formerly PLX Technology)
--
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH 3/3] dt-bindings: iio: chemical: pms7003: add device tree support
  2019-01-06 17:16 [PATCH 0/3] add support for PMS7003 PM sensor Tomasz Duszynski
  2019-01-06 17:16 ` [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor Tomasz Duszynski
  2019-01-06 17:16 ` [PATCH 2/3] dt-bindings: add Plantower to the vendor prefixes Tomasz Duszynski
@ 2019-01-06 17:16 ` Tomasz Duszynski
  2019-01-11 22:15   ` Rob Herring
  2 siblings, 1 reply; 11+ messages in thread
From: Tomasz Duszynski @ 2019-01-06 17:16 UTC (permalink / raw)
  To: linux-iio; +Cc: linux-kernel, devicetree, Tomasz Duszynski

Add device tree support for Plantower PMS7003 particulate matter sensor.

Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
---
 .../bindings/iio/chemical/plantower,pms7003.txt    | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt

diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
new file mode 100644
index 000000000000..79eb538eb932
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
@@ -0,0 +1,14 @@
+* Plantower PMS7003 particulate matter sensor
+
+Required properties:
+- compatible: must be "plantower,pms7003"
+
+Refer to serial/slave-device.txt for generic serial attached device bindings.
+
+Example:
+
+&uart@0 {
+	pms7003 {
+		compatible = "plantower,pms7003";
+	};
+};
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor
  2019-01-06 17:16 ` [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor Tomasz Duszynski
@ 2019-01-07 15:35   ` Johan Hovold
  2019-01-08 19:07     ` Tomasz Duszynski
  2019-01-12 17:48   ` Jonathan Cameron
  1 sibling, 1 reply; 11+ messages in thread
From: Johan Hovold @ 2019-01-07 15:35 UTC (permalink / raw)
  To: Tomasz Duszynski; +Cc: linux-iio, linux-kernel, devicetree

On Sun, Jan 06, 2019 at 06:16:12PM +0100, Tomasz Duszynski wrote:
> Add support for Plantower PMS7003 particulate matter sensor.
> 
> Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>

> +static int pms7003_do_cmd(struct pms7003_state *state, u8 cmd)
> +{
> +	/*
> +	 * commands have following format:
> +	 *
> +	 * +------+------+-----+------+-----+-----------+-----------+
> +	 * | 0x42 | 0x4d | cmd | 0x00 | arg | cksum msb | cksum lsb |
> +	 * +------+------+-----+------+-----+-----------+-----------+
> +	 */
> +	u8 tmp[PMS7003_CMD_LENGTH] = { PMS7003_MAGIC_MSB, PMS7003_MAGIC_LSB };
> +	int ret, n = 2;
> +	u16 checksum;
> +
> +	switch (cmd) {
> +	case CMD_WAKEUP:
> +		tmp[n++] = 0xe4;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x01;
> +		break;
> +	case CMD_ENTER_PASSIVE_MODE:
> +		tmp[n++] = 0xe1;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x00;
> +		break;
> +	case CMD_READ_PASSIVE:
> +		tmp[n++] = 0xe2;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x00;
> +		break;
> +	case CMD_SLEEP:
> +		tmp[n++] = 0xe4;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x00;
> +		break;
> +	}
> +
> +	checksum = pms7003_calc_checksum(tmp, n);
> +	put_unaligned_be16(checksum, tmp + n);
> +	n += PMS7003_CHECKSUM_LENGTH;
> +
> +	ret = serdev_device_write(state->serdev, tmp, n, PMS7003_TIMEOUT);
> +	if (ret)
> +		return ret;

Beginning with 5.0, serdev_device_write() returns the number of bytes
written before timeout (or being interrupted) so you need to check
against < n here.

Johan

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor
  2019-01-07 15:35   ` Johan Hovold
@ 2019-01-08 19:07     ` Tomasz Duszynski
  0 siblings, 0 replies; 11+ messages in thread
From: Tomasz Duszynski @ 2019-01-08 19:07 UTC (permalink / raw)
  To: Johan Hovold; +Cc: Tomasz Duszynski, linux-iio, linux-kernel, devicetree

On Mon, Jan 07, 2019 at 04:35:42PM +0100, Johan Hovold wrote:
> On Sun, Jan 06, 2019 at 06:16:12PM +0100, Tomasz Duszynski wrote:
> > Add support for Plantower PMS7003 particulate matter sensor.
> >
> > Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
>
> > +static int pms7003_do_cmd(struct pms7003_state *state, u8 cmd)
> > +{
> > +	/*
> > +	 * commands have following format:
> > +	 *
> > +	 * +------+------+-----+------+-----+-----------+-----------+
> > +	 * | 0x42 | 0x4d | cmd | 0x00 | arg | cksum msb | cksum lsb |
> > +	 * +------+------+-----+------+-----+-----------+-----------+
> > +	 */
> > +	u8 tmp[PMS7003_CMD_LENGTH] = { PMS7003_MAGIC_MSB, PMS7003_MAGIC_LSB };
> > +	int ret, n = 2;
> > +	u16 checksum;
> > +
> > +	switch (cmd) {
> > +	case CMD_WAKEUP:
> > +		tmp[n++] = 0xe4;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x01;
> > +		break;
> > +	case CMD_ENTER_PASSIVE_MODE:
> > +		tmp[n++] = 0xe1;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x00;
> > +		break;
> > +	case CMD_READ_PASSIVE:
> > +		tmp[n++] = 0xe2;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x00;
> > +		break;
> > +	case CMD_SLEEP:
> > +		tmp[n++] = 0xe4;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x00;
> > +		break;
> > +	}
> > +
> > +	checksum = pms7003_calc_checksum(tmp, n);
> > +	put_unaligned_be16(checksum, tmp + n);
> > +	n += PMS7003_CHECKSUM_LENGTH;
> > +
> > +	ret = serdev_device_write(state->serdev, tmp, n, PMS7003_TIMEOUT);
> > +	if (ret)
> > +		return ret;
>
> Beginning with 5.0, serdev_device_write() returns the number of bytes
> written before timeout (or being interrupted) so you need to check
> against < n here.
>

Right, on the second though that can be simplified by just ignoring
return value I guess. Anyway, thanks for pointing this out.

> Johan

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH 2/3] dt-bindings: add Plantower to the vendor prefixes
  2019-01-06 17:16 ` [PATCH 2/3] dt-bindings: add Plantower to the vendor prefixes Tomasz Duszynski
@ 2019-01-11 22:12   ` Rob Herring
  0 siblings, 0 replies; 11+ messages in thread
From: Rob Herring @ 2019-01-11 22:12 UTC (permalink / raw)
  To: Tomasz Duszynski; +Cc: linux-iio, linux-kernel, devicetree, Tomasz Duszynski

On Sun,  6 Jan 2019 18:16:13 +0100, Tomasz Duszynski wrote:
> Add Plantower to the vendor prefixes.
> 
> Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>  1 file changed, 1 insertion(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH 3/3] dt-bindings: iio: chemical: pms7003: add device tree support
  2019-01-06 17:16 ` [PATCH 3/3] dt-bindings: iio: chemical: pms7003: add device tree support Tomasz Duszynski
@ 2019-01-11 22:15   ` Rob Herring
  2019-01-27 13:45     ` Tomasz Duszynski
  0 siblings, 1 reply; 11+ messages in thread
From: Rob Herring @ 2019-01-11 22:15 UTC (permalink / raw)
  To: Tomasz Duszynski; +Cc: linux-iio, linux-kernel, devicetree

On Sun, Jan 06, 2019 at 06:16:14PM +0100, Tomasz Duszynski wrote:
> Add device tree support for Plantower PMS7003 particulate matter sensor.
> 
> Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
> ---
>  .../bindings/iio/chemical/plantower,pms7003.txt    | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
> 
> diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
> new file mode 100644
> index 000000000000..79eb538eb932
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
> @@ -0,0 +1,14 @@
> +* Plantower PMS7003 particulate matter sensor
> +
> +Required properties:
> +- compatible: must be "plantower,pms7003"

Looks like this has reset and set GPIO lines as well as Vcc supply. 
Bindings should be complete even if the driver or a platform doesn't use 
some parts.

> +
> +Refer to serial/slave-device.txt for generic serial attached device bindings.
> +
> +Example:
> +
> +&uart@0 {
> +	pms7003 {
> +		compatible = "plantower,pms7003";
> +	};
> +};
> -- 
> 2.20.1
> 

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor
  2019-01-06 17:16 ` [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor Tomasz Duszynski
  2019-01-07 15:35   ` Johan Hovold
@ 2019-01-12 17:48   ` Jonathan Cameron
  2019-01-23 21:08     ` Tomasz Duszynski
  1 sibling, 1 reply; 11+ messages in thread
From: Jonathan Cameron @ 2019-01-12 17:48 UTC (permalink / raw)
  To: Tomasz Duszynski; +Cc: linux-iio, linux-kernel, devicetree

On Sun,  6 Jan 2019 18:16:12 +0100
Tomasz Duszynski <tduszyns@gmail.com> wrote:

> Add support for Plantower PMS7003 particulate matter sensor.
> 
> Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>

A few minor bits and pieces from me.

Jonathan

> ---
>  drivers/iio/chemical/Kconfig   |  10 +
>  drivers/iio/chemical/Makefile  |   1 +
>  drivers/iio/chemical/pms7003.c | 411 +++++++++++++++++++++++++++++++++
>  3 files changed, 422 insertions(+)
>  create mode 100644 drivers/iio/chemical/pms7003.c
> 
> diff --git a/drivers/iio/chemical/Kconfig b/drivers/iio/chemical/Kconfig
> index 57832b4360e9..d5d146e9e372 100644
> --- a/drivers/iio/chemical/Kconfig
> +++ b/drivers/iio/chemical/Kconfig
> @@ -61,6 +61,16 @@ config IAQCORE
>  	  iAQ-Core Continuous/Pulsed VOC (Volatile Organic Compounds)
>  	  sensors
>  
> +config PMS7003
> +	tristate "Plantower PMS7003 particulate matter sensor"
> +	depends on SERIAL_DEV_BUS
> +	help
> +	  Say Y here to build support for the Plantower PMS7003 particulate
> +	  matter sensor.
> +
> +	  To compile this driver as a module, choose M here: the module will
> +	  be called pms7003.
> +
>  config SPS30
>  	tristate "SPS30 particulate matter sensor"
>  	depends on I2C
> diff --git a/drivers/iio/chemical/Makefile b/drivers/iio/chemical/Makefile
> index 65bf0f89c0e4..f5d1365acb49 100644
> --- a/drivers/iio/chemical/Makefile
> +++ b/drivers/iio/chemical/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_BME680_I2C) += bme680_i2c.o
>  obj-$(CONFIG_BME680_SPI) += bme680_spi.o
>  obj-$(CONFIG_CCS811)		+= ccs811.o
>  obj-$(CONFIG_IAQCORE)		+= ams-iaq-core.o
> +obj-$(CONFIG_PMS7003) += pms7003.o
>  obj-$(CONFIG_SENSIRION_SGP30)	+= sgp30.o
>  obj-$(CONFIG_SPS30) += sps30.o
>  obj-$(CONFIG_VZ89X)		+= vz89x.o
> diff --git a/drivers/iio/chemical/pms7003.c b/drivers/iio/chemical/pms7003.c
> new file mode 100644
> index 000000000000..bc8a4fbdf641
> --- /dev/null
> +++ b/drivers/iio/chemical/pms7003.c
> @@ -0,0 +1,411 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Plantower PMS7003 particulate matter sensor driver
> + *
> + * Copyright (c) Tomasz Duszynski <tduszyns@gmail.com>
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <asm/unaligned.h>
> +#include <linux/completion.h>
> +#include <linux/device.h>
> +#include <linux/errno.h>
> +#include <linux/iio/buffer.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/trigger_consumer.h>
> +#include <linux/iio/triggered_buffer.h>
> +#include <linux/jiffies.h>
> +#include <linux/kernel.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/serdev.h>
> +
> +#define PMS7003_DRIVER_NAME "pms7003"
> +
> +#define PMS7003_MAGIC_MSB 0x42
> +#define PMS7003_MAGIC_LSB 0x4d
> +/* last 2 data bytes hold frame checksum */
> +#define PMS7003_MAX_DATA_LENGTH 28
> +#define PMS7003_CHECKSUM_LENGTH 2
> +#define PMS7003_PM10_OFFSET 10
> +#define PMS7003_PM2P5_OFFSET 8
> +#define PMS7003_PM1_OFFSET 6
> +
> +#define PMS7003_TIMEOUT msecs_to_jiffies(6000)
> +#define PMS7003_CMD_LENGTH 7
> +#define PMS7003_PM_MAX 1000
> +#define PMS7003_PM_MIN 0
> +
> +enum {
> +	PM1,
> +	PM2P5,
> +	PM10,
> +};
> +
> +enum {
> +	CMD_WAKEUP,
> +	CMD_ENTER_PASSIVE_MODE,
> +	CMD_READ_PASSIVE,
> +	CMD_SLEEP,
> +};
> +
> +enum {
> +	STATE_MAGIC_MSB,
> +	STATE_MAGIC_LSB,
> +	STATE_LENGTH_MSB,
> +	STATE_LENGTH_LSB,
> +	STATE_DATA,
> +};
> +
> +struct pms7003_frame {
> +	u8 data[PMS7003_MAX_DATA_LENGTH];
> +	u16 expected_length;
> +	u16 length;
> +	int state;
> +};
> +
> +struct pms7003_state {
> +	struct serdev_device *serdev;
> +	struct pms7003_frame frame;
> +	struct completion frame_ready;
> +	struct mutex lock; /* must be held whenever state gets touched */
> +};
> +
> +static u16 pms7003_calc_checksum(const u8 *data, int size)
> +{
> +	u16 checksum = 0;
> +
> +	while (size--)
> +		checksum += data[size];
> +
> +	return checksum;
> +}
> +
> +static int pms7003_do_cmd(struct pms7003_state *state, u8 cmd)

Use the enum not u8.

> +{
> +	/*
> +	 * commands have following format:
> +	 *
> +	 * +------+------+-----+------+-----+-----------+-----------+
> +	 * | 0x42 | 0x4d | cmd | 0x00 | arg | cksum msb | cksum lsb |
> +	 * +------+------+-----+------+-----+-----------+-----------+
> +	 */
> +	u8 tmp[PMS7003_CMD_LENGTH] = { PMS7003_MAGIC_MSB, PMS7003_MAGIC_LSB };
> +	int ret, n = 2;
> +	u16 checksum;
> +
> +	switch (cmd) {
> +	case CMD_WAKEUP:
> +		tmp[n++] = 0xe4;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x01;
> +		break;
> +	case CMD_ENTER_PASSIVE_MODE:
> +		tmp[n++] = 0xe1;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x00;
> +		break;
> +	case CMD_READ_PASSIVE:
> +		tmp[n++] = 0xe2;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x00;
> +		break;
> +	case CMD_SLEEP:
> +		tmp[n++] = 0xe4;
> +		tmp[n++] = 0x00;
> +		tmp[n++] = 0x00;

These look like they should be in a look up table to me rather than the more
verbose switch statement.

> +		break;
> +	}
> +
> +	checksum = pms7003_calc_checksum(tmp, n);

This is fixed for all calls of a given command (I think).  If so, it would
be good to precompute it (on startup for example, ideally letting the compiler
figure it out if it can).

> +	put_unaligned_be16(checksum, tmp + n);
> +	n += PMS7003_CHECKSUM_LENGTH;
> +
> +	ret = serdev_device_write(state->serdev, tmp, n, PMS7003_TIMEOUT);
> +	if (ret)
> +		return ret;
> +
> +	ret = wait_for_completion_interruptible_timeout(&state->frame_ready,
> +							PMS7003_TIMEOUT);
> +	if (!ret)
> +		ret = -ETIMEDOUT;
> +
> +	return ret < 0 ? ret : 0;
> +}
> +
> +static u16 pms7003_get_pm(struct pms7003_frame *frame, int offset)
> +{
> +	return clamp_val(get_unaligned_be16(frame->data + offset),
> +			 PMS7003_PM_MIN, PMS7003_PM_MAX);
> +}
> +
> +static irqreturn_t pms7003_trigger_handler(int irq, void *p)
> +{
> +	struct iio_poll_func *pf = p;
> +	struct iio_dev *indio_dev = pf->indio_dev;
> +	struct pms7003_state *state = iio_priv(indio_dev);
> +	struct pms7003_frame *frame = &state->frame;
> +	u16 data[3 + 1 + 4]; /* PM1, PM2P5, PM10, padding, timestamp */
> +	int ret;
> +
> +	mutex_lock(&state->lock);
> +	ret = pms7003_do_cmd(state, CMD_READ_PASSIVE);
> +	if (ret) {
> +		mutex_unlock(&state->lock);
> +		goto err;
> +	}
> +
> +	data[PM1] = pms7003_get_pm(frame, PMS7003_PM1_OFFSET);
> +	data[PM2P5] = pms7003_get_pm(frame, PMS7003_PM2P5_OFFSET);
> +	data[PM10] = pms7003_get_pm(frame, PMS7003_PM10_OFFSET);

> +	mutex_unlock(&state->lock);
> +
> +	iio_push_to_buffers_with_timestamp(indio_dev, data,
> +					   iio_get_time_ns(indio_dev));
> +err:
> +	iio_trigger_notify_done(indio_dev->trig);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int pms7003_read_raw(struct iio_dev *indio_dev,
> +			    struct iio_chan_spec const *chan,
> +			    int *val, int *val2, long mask)
> +{
> +	struct pms7003_state *state = iio_priv(indio_dev);
> +	struct pms7003_frame *frame = &state->frame;

This local variable for the frame can go away once you make the other
change suggested below.

> +	int ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_PROCESSED:
> +		switch (chan->type) {
> +		case IIO_MASSCONCENTRATION:
> +			mutex_lock(&state->lock);

Will this interfere in any way with buffered operation?  I'd normally
expect to see some claim_direct etc calls in here to prevent that.

> +			ret = pms7003_do_cmd(state, CMD_READ_PASSIVE);
> +			if (ret) {
> +				mutex_unlock(&state->lock);
> +				return ret;
> +			}
> +
> +			switch (chan->channel2) {
> +			case IIO_MOD_PM1:
> +				*val = pms7003_get_pm(frame,
> +						      PMS7003_PM1_OFFSET);

Put the PMS7003_PM1_OFFSET in the address element of the channel then
you can get rid fo this switch statement.

> +				break;
> +			case IIO_MOD_PM2P5:
> +				*val = pms7003_get_pm(frame,
> +						      PMS7003_PM2P5_OFFSET);
> +				break;
> +			case IIO_MOD_PM10:
> +				*val = pms7003_get_pm(frame,
> +						      PMS7003_PM10_OFFSET);
> +				break;

Just possible some compiler will give us warnings for the lack of a default
in here.  Might be worth putting one in to avoid that noise.
Particularly as you already have one for the chan->type.

> +			}
> +			mutex_unlock(&state->lock);
> +
> +			return IIO_VAL_INT;
> +		default:
> +			return -EINVAL;
> +		}
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +
> +static const struct iio_info pms7003_info = {
> +	.read_raw = pms7003_read_raw,
> +};
> +
> +#define PMS7003_CHAN(_index, _mod) { \
> +	.type = IIO_MASSCONCENTRATION, \
> +	.modified = 1, \
> +	.channel2 = IIO_MOD_ ## _mod, \
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), \
> +	.scan_index = _index, \
> +	.scan_type = { \
> +		.sign = 'u', \
> +		.realbits = 10, \
> +		.storagebits = 16, \
> +		.endianness = IIO_CPU, \
> +	}, \
> +}
> +
> +static const struct iio_chan_spec pms7003_channels[] = {
> +	PMS7003_CHAN(0, PM1),
> +	PMS7003_CHAN(1, PM2P5),
> +	PMS7003_CHAN(2, PM10),
> +	IIO_CHAN_SOFT_TIMESTAMP(3),
> +};
> +
> +static int pms7003_frame_okay(struct pms7003_frame *frame)
> +{
> +	int offset = frame->length - PMS7003_CHECKSUM_LENGTH;
> +	u16 checksum = PMS7003_MAGIC_MSB + PMS7003_MAGIC_LSB +
> +		       (frame->length >> 8) + (u8)frame->length +
> +		       pms7003_calc_checksum(frame->data, offset);
> +
> +	return checksum == get_unaligned_be16(frame->data + offset);
> +}
> +

The returning of 1 or 0 is not entirely obvious.  Please provide
some documentation on what that is doing.

This doesn't seem like an entirely obvious construct in general.

Given we can't (I think) do anything much useful with the data until
we get a whole frame, why not simply buffer it up unprocessed until
we have enough data to process it in one go?

On first packet dump data until you get that start markers.  After that
wait until you have the 'header' (length) and then wait until all data
is available keeping it in a raw buffer.

A state machine that is a simple step through like this one with only
one path ends up less readable to my eye than buffer data and
process when all there...


> +static int pms7003_update_frame(struct pms7003_frame *frame, u8 byte)
> +{
> +	switch (frame->state) {
> +	case STATE_MAGIC_MSB:
> +		if (byte != PMS7003_MAGIC_MSB)
> +			return 1;
> +		frame->state = STATE_MAGIC_LSB;
> +		frame->length = 0;
> +		return 1;
> +	case STATE_MAGIC_LSB:
> +		if (byte != PMS7003_MAGIC_LSB) {
> +			frame->state = STATE_MAGIC_MSB;
> +			return 1;
> +		}
> +		frame->state = STATE_LENGTH_MSB;
> +		return 1;
> +	case STATE_LENGTH_MSB:
> +		frame->expected_length = (u16)byte << 8;
> +		frame->state = STATE_LENGTH_LSB;
> +		return 1;
> +	case STATE_LENGTH_LSB:
> +		frame->expected_length |= byte;
> +		frame->state = STATE_DATA;
> +		return 1;
> +	case STATE_DATA:
> +		if (frame->length > PMS7003_MAX_DATA_LENGTH) {
> +			frame->state = STATE_MAGIC_MSB;
> +			return 1;
> +		}
> +
> +		frame->data[frame->length++] = byte;
> +
> +		if (frame->length != frame->expected_length)
> +			return 1;
> +
> +		if (!pms7003_frame_okay(frame)) {
> +			frame->state = STATE_MAGIC_MSB;
> +			return 1;
> +		}
> +
> +		frame->state = STATE_MAGIC_MSB;
> +		break;
> +	}
> +
> +	return 0;
> +}
> +
> +static int pms7003_receive_buf(struct serdev_device *serdev,
> +			       const unsigned char *buf, size_t size)
> +{
> +	struct iio_dev *indio_dev = serdev_device_get_drvdata(serdev);
> +	struct pms7003_state *state = iio_priv(indio_dev);
> +	struct pms7003_frame *frame = &state->frame;
> +	int i, ret;
> +
> +	for (i = 0; i < size; i++) {
> +		ret = pms7003_update_frame(frame, buf[i]);
> +		if (ret)
> +			continue;
Given this is the normal path (continue) I would invert the
logic to be
	if (!ret) {
		complete
		return..
	}

Trivial but perhaps slightly easier to follow.

> +
> +		complete(&state->frame_ready);
> +		return i + 1;
> +	}
> +
> +	return size;
> +}
> +
> +static const struct serdev_device_ops pms7003_serdev_ops = {
> +	.receive_buf = pms7003_receive_buf,
> +	.write_wakeup = serdev_device_write_wakeup,
> +};
> +
> +static void pms7003_stop(void *data)
> +{
> +	struct pms7003_state *state = data;
> +
> +	pms7003_do_cmd(state, CMD_SLEEP);
> +}
> +
> +static const unsigned long pms7003_scan_masks[] = { 0x07, 0x00 };
> +
> +static int pms7003_probe(struct serdev_device *serdev)
> +{
> +	struct pms7003_state *state;
> +	struct iio_dev *indio_dev;
> +	int ret;
> +
> +	indio_dev = devm_iio_device_alloc(&serdev->dev, sizeof(*state));
> +	if (!indio_dev)
> +		return -ENOMEM;
> +
> +	state = iio_priv(indio_dev);
> +	serdev_device_set_drvdata(serdev, indio_dev);
> +	state->serdev = serdev;
> +	indio_dev->dev.parent = &serdev->dev;
> +	indio_dev->info = &pms7003_info;
> +	indio_dev->name = PMS7003_DRIVER_NAME;
> +	indio_dev->channels = pms7003_channels,
> +	indio_dev->num_channels = ARRAY_SIZE(pms7003_channels);
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +	indio_dev->available_scan_masks = pms7003_scan_masks;
> +
> +	mutex_init(&state->lock);
> +	init_completion(&state->frame_ready);
> +
> +	serdev_device_set_client_ops(serdev, &pms7003_serdev_ops);
> +	ret = devm_serdev_device_open(&serdev->dev, serdev);
> +	if (ret)
> +		return ret;
> +
> +	serdev_device_set_baudrate(serdev, 9600);
> +	serdev_device_set_flow_control(serdev, false);
> +
> +	ret = serdev_device_set_parity(serdev, SERDEV_PARITY_NONE);
> +	if (ret)
> +		return ret;
> +
> +	ret = pms7003_do_cmd(state, CMD_WAKEUP);
> +	if (ret) {
> +		dev_err(&serdev->dev, "failed to wakeup sensor\n");
> +		return ret;
> +	}
> +
> +	ret = pms7003_do_cmd(state, CMD_ENTER_PASSIVE_MODE);
> +	if (ret) {
> +		dev_err(&serdev->dev, "failed to enter passive mode\n");
> +		return ret;
> +	}
> +
> +	ret = devm_add_action_or_reset(&serdev->dev, pms7003_stop, state);
> +	if (ret)
> +		return ret;
> +
> +	ret = devm_iio_triggered_buffer_setup(&serdev->dev, indio_dev, NULL,
> +					      pms7003_trigger_handler, NULL);
> +	if (ret)
> +		return ret;
> +
> +	return devm_iio_device_register(&serdev->dev, indio_dev);
> +}
> +
> +static const struct of_device_id pms7003_of_match[] = {
> +	{ .compatible = "plantower,pms7003" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, pms7003_of_match);
> +
> +static struct serdev_device_driver pms7003_driver = {
> +	.driver = {
> +		.name = PMS7003_DRIVER_NAME,
> +		.of_match_table = pms7003_of_match,
> +	},
> +	.probe = pms7003_probe,
> +};
> +module_serdev_device_driver(pms7003_driver);
> +
> +MODULE_AUTHOR("Tomasz Duszynski <tduszyns@gmail.com>");
> +MODULE_DESCRIPTION("Plantower PMS7003 particulate matter sensor driver");
> +MODULE_LICENSE("GPL v2");


^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor
  2019-01-12 17:48   ` Jonathan Cameron
@ 2019-01-23 21:08     ` Tomasz Duszynski
  0 siblings, 0 replies; 11+ messages in thread
From: Tomasz Duszynski @ 2019-01-23 21:08 UTC (permalink / raw)
  To: Jonathan Cameron; +Cc: Tomasz Duszynski, linux-iio, linux-kernel, devicetree

On Sat, Jan 12, 2019 at 05:48:22PM +0000, Jonathan Cameron wrote:
> On Sun,  6 Jan 2019 18:16:12 +0100
> Tomasz Duszynski <tduszyns@gmail.com> wrote:
>
> > Add support for Plantower PMS7003 particulate matter sensor.
> >
> > Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
>
> A few minor bits and pieces from me.
>

Just one minor comment inline and ACK to all other improvements you
suggested.

> Jonathan
>
> > ---
> >  drivers/iio/chemical/Kconfig   |  10 +
> >  drivers/iio/chemical/Makefile  |   1 +
> >  drivers/iio/chemical/pms7003.c | 411 +++++++++++++++++++++++++++++++++
> >  3 files changed, 422 insertions(+)
> >  create mode 100644 drivers/iio/chemical/pms7003.c
> >
> > diff --git a/drivers/iio/chemical/Kconfig b/drivers/iio/chemical/Kconfig
> > index 57832b4360e9..d5d146e9e372 100644
> > --- a/drivers/iio/chemical/Kconfig
> > +++ b/drivers/iio/chemical/Kconfig
> > @@ -61,6 +61,16 @@ config IAQCORE
> >  	  iAQ-Core Continuous/Pulsed VOC (Volatile Organic Compounds)
> >  	  sensors
> >
> > +config PMS7003
> > +	tristate "Plantower PMS7003 particulate matter sensor"
> > +	depends on SERIAL_DEV_BUS
> > +	help
> > +	  Say Y here to build support for the Plantower PMS7003 particulate
> > +	  matter sensor.
> > +
> > +	  To compile this driver as a module, choose M here: the module will
> > +	  be called pms7003.
> > +
> >  config SPS30
> >  	tristate "SPS30 particulate matter sensor"
> >  	depends on I2C
> > diff --git a/drivers/iio/chemical/Makefile b/drivers/iio/chemical/Makefile
> > index 65bf0f89c0e4..f5d1365acb49 100644
> > --- a/drivers/iio/chemical/Makefile
> > +++ b/drivers/iio/chemical/Makefile
> > @@ -9,6 +9,7 @@ obj-$(CONFIG_BME680_I2C) += bme680_i2c.o
> >  obj-$(CONFIG_BME680_SPI) += bme680_spi.o
> >  obj-$(CONFIG_CCS811)		+= ccs811.o
> >  obj-$(CONFIG_IAQCORE)		+= ams-iaq-core.o
> > +obj-$(CONFIG_PMS7003) += pms7003.o
> >  obj-$(CONFIG_SENSIRION_SGP30)	+= sgp30.o
> >  obj-$(CONFIG_SPS30) += sps30.o
> >  obj-$(CONFIG_VZ89X)		+= vz89x.o
> > diff --git a/drivers/iio/chemical/pms7003.c b/drivers/iio/chemical/pms7003.c
> > new file mode 100644
> > index 000000000000..bc8a4fbdf641
> > --- /dev/null
> > +++ b/drivers/iio/chemical/pms7003.c
> > @@ -0,0 +1,411 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Plantower PMS7003 particulate matter sensor driver
> > + *
> > + * Copyright (c) Tomasz Duszynski <tduszyns@gmail.com>
> > + */
> > +
> > +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> > +
> > +#include <asm/unaligned.h>
> > +#include <linux/completion.h>
> > +#include <linux/device.h>
> > +#include <linux/errno.h>
> > +#include <linux/iio/buffer.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/iio/trigger_consumer.h>
> > +#include <linux/iio/triggered_buffer.h>
> > +#include <linux/jiffies.h>
> > +#include <linux/kernel.h>
> > +#include <linux/mod_devicetable.h>
> > +#include <linux/module.h>
> > +#include <linux/mutex.h>
> > +#include <linux/serdev.h>
> > +
> > +#define PMS7003_DRIVER_NAME "pms7003"
> > +
> > +#define PMS7003_MAGIC_MSB 0x42
> > +#define PMS7003_MAGIC_LSB 0x4d
> > +/* last 2 data bytes hold frame checksum */
> > +#define PMS7003_MAX_DATA_LENGTH 28
> > +#define PMS7003_CHECKSUM_LENGTH 2
> > +#define PMS7003_PM10_OFFSET 10
> > +#define PMS7003_PM2P5_OFFSET 8
> > +#define PMS7003_PM1_OFFSET 6
> > +
> > +#define PMS7003_TIMEOUT msecs_to_jiffies(6000)
> > +#define PMS7003_CMD_LENGTH 7
> > +#define PMS7003_PM_MAX 1000
> > +#define PMS7003_PM_MIN 0
> > +
> > +enum {
> > +	PM1,
> > +	PM2P5,
> > +	PM10,
> > +};
> > +
> > +enum {
> > +	CMD_WAKEUP,
> > +	CMD_ENTER_PASSIVE_MODE,
> > +	CMD_READ_PASSIVE,
> > +	CMD_SLEEP,
> > +};
> > +
> > +enum {
> > +	STATE_MAGIC_MSB,
> > +	STATE_MAGIC_LSB,
> > +	STATE_LENGTH_MSB,
> > +	STATE_LENGTH_LSB,
> > +	STATE_DATA,
> > +};
> > +
> > +struct pms7003_frame {
> > +	u8 data[PMS7003_MAX_DATA_LENGTH];
> > +	u16 expected_length;
> > +	u16 length;
> > +	int state;
> > +};
> > +
> > +struct pms7003_state {
> > +	struct serdev_device *serdev;
> > +	struct pms7003_frame frame;
> > +	struct completion frame_ready;
> > +	struct mutex lock; /* must be held whenever state gets touched */
> > +};
> > +
> > +static u16 pms7003_calc_checksum(const u8 *data, int size)
> > +{
> > +	u16 checksum = 0;
> > +
> > +	while (size--)
> > +		checksum += data[size];
> > +
> > +	return checksum;
> > +}
> > +
> > +static int pms7003_do_cmd(struct pms7003_state *state, u8 cmd)
>
> Use the enum not u8.
>
> > +{
> > +	/*
> > +	 * commands have following format:
> > +	 *
> > +	 * +------+------+-----+------+-----+-----------+-----------+
> > +	 * | 0x42 | 0x4d | cmd | 0x00 | arg | cksum msb | cksum lsb |
> > +	 * +------+------+-----+------+-----+-----------+-----------+
> > +	 */
> > +	u8 tmp[PMS7003_CMD_LENGTH] = { PMS7003_MAGIC_MSB, PMS7003_MAGIC_LSB };
> > +	int ret, n = 2;
> > +	u16 checksum;
> > +
> > +	switch (cmd) {
> > +	case CMD_WAKEUP:
> > +		tmp[n++] = 0xe4;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x01;
> > +		break;
> > +	case CMD_ENTER_PASSIVE_MODE:
> > +		tmp[n++] = 0xe1;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x00;
> > +		break;
> > +	case CMD_READ_PASSIVE:
> > +		tmp[n++] = 0xe2;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x00;
> > +		break;
> > +	case CMD_SLEEP:
> > +		tmp[n++] = 0xe4;
> > +		tmp[n++] = 0x00;
> > +		tmp[n++] = 0x00;
>
> These look like they should be in a look up table to me rather than the more
> verbose switch statement.
>
> > +		break;
> > +	}
> > +
> > +	checksum = pms7003_calc_checksum(tmp, n);
>
> This is fixed for all calls of a given command (I think).  If so, it would
> be good to precompute it (on startup for example, ideally letting the compiler
> figure it out if it can).
>
> > +	put_unaligned_be16(checksum, tmp + n);
> > +	n += PMS7003_CHECKSUM_LENGTH;
> > +
> > +	ret = serdev_device_write(state->serdev, tmp, n, PMS7003_TIMEOUT);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = wait_for_completion_interruptible_timeout(&state->frame_ready,
> > +							PMS7003_TIMEOUT);
> > +	if (!ret)
> > +		ret = -ETIMEDOUT;
> > +
> > +	return ret < 0 ? ret : 0;
> > +}
> > +
> > +static u16 pms7003_get_pm(struct pms7003_frame *frame, int offset)
> > +{
> > +	return clamp_val(get_unaligned_be16(frame->data + offset),
> > +			 PMS7003_PM_MIN, PMS7003_PM_MAX);
> > +}
> > +
> > +static irqreturn_t pms7003_trigger_handler(int irq, void *p)
> > +{
> > +	struct iio_poll_func *pf = p;
> > +	struct iio_dev *indio_dev = pf->indio_dev;
> > +	struct pms7003_state *state = iio_priv(indio_dev);
> > +	struct pms7003_frame *frame = &state->frame;
> > +	u16 data[3 + 1 + 4]; /* PM1, PM2P5, PM10, padding, timestamp */
> > +	int ret;
> > +
> > +	mutex_lock(&state->lock);
> > +	ret = pms7003_do_cmd(state, CMD_READ_PASSIVE);
> > +	if (ret) {
> > +		mutex_unlock(&state->lock);
> > +		goto err;
> > +	}
> > +
> > +	data[PM1] = pms7003_get_pm(frame, PMS7003_PM1_OFFSET);
> > +	data[PM2P5] = pms7003_get_pm(frame, PMS7003_PM2P5_OFFSET);
> > +	data[PM10] = pms7003_get_pm(frame, PMS7003_PM10_OFFSET);
>
> > +	mutex_unlock(&state->lock);
> > +
> > +	iio_push_to_buffers_with_timestamp(indio_dev, data,
> > +					   iio_get_time_ns(indio_dev));
> > +err:
> > +	iio_trigger_notify_done(indio_dev->trig);
> > +
> > +	return IRQ_HANDLED;
> > +}
> > +
> > +static int pms7003_read_raw(struct iio_dev *indio_dev,
> > +			    struct iio_chan_spec const *chan,
> > +			    int *val, int *val2, long mask)
> > +{
> > +	struct pms7003_state *state = iio_priv(indio_dev);
> > +	struct pms7003_frame *frame = &state->frame;
>
> This local variable for the frame can go away once you make the other
> change suggested below.
>
> > +	int ret;
> > +
> > +	switch (mask) {
> > +	case IIO_CHAN_INFO_PROCESSED:
> > +		switch (chan->type) {
> > +		case IIO_MASSCONCENTRATION:
> > +			mutex_lock(&state->lock);
>
> Will this interfere in any way with buffered operation?  I'd normally
> expect to see some claim_direct etc calls in here to prevent that.
>

In either case full data access is protected with a lock hence
I do not expect to see any surprises here.

> > +			ret = pms7003_do_cmd(state, CMD_READ_PASSIVE);
> > +			if (ret) {
> > +				mutex_unlock(&state->lock);
> > +				return ret;
> > +			}
> > +
> > +			switch (chan->channel2) {
> > +			case IIO_MOD_PM1:
> > +				*val = pms7003_get_pm(frame,
> > +						      PMS7003_PM1_OFFSET);
>
> Put the PMS7003_PM1_OFFSET in the address element of the channel then
> you can get rid fo this switch statement.
>
> > +				break;
> > +			case IIO_MOD_PM2P5:
> > +				*val = pms7003_get_pm(frame,
> > +						      PMS7003_PM2P5_OFFSET);
> > +				break;
> > +			case IIO_MOD_PM10:
> > +				*val = pms7003_get_pm(frame,
> > +						      PMS7003_PM10_OFFSET);
> > +				break;
>
> Just possible some compiler will give us warnings for the lack of a default
> in here.  Might be worth putting one in to avoid that noise.
> Particularly as you already have one for the chan->type.
>
> > +			}
> > +			mutex_unlock(&state->lock);
> > +
> > +			return IIO_VAL_INT;
> > +		default:
> > +			return -EINVAL;
> > +		}
> > +	}
> > +
> > +	return -EINVAL;
> > +}
> > +
> > +
> > +static const struct iio_info pms7003_info = {
> > +	.read_raw = pms7003_read_raw,
> > +};
> > +
> > +#define PMS7003_CHAN(_index, _mod) { \
> > +	.type = IIO_MASSCONCENTRATION, \
> > +	.modified = 1, \
> > +	.channel2 = IIO_MOD_ ## _mod, \
> > +	.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), \
> > +	.scan_index = _index, \
> > +	.scan_type = { \
> > +		.sign = 'u', \
> > +		.realbits = 10, \
> > +		.storagebits = 16, \
> > +		.endianness = IIO_CPU, \
> > +	}, \
> > +}
> > +
> > +static const struct iio_chan_spec pms7003_channels[] = {
> > +	PMS7003_CHAN(0, PM1),
> > +	PMS7003_CHAN(1, PM2P5),
> > +	PMS7003_CHAN(2, PM10),
> > +	IIO_CHAN_SOFT_TIMESTAMP(3),
> > +};
> > +
> > +static int pms7003_frame_okay(struct pms7003_frame *frame)
> > +{
> > +	int offset = frame->length - PMS7003_CHECKSUM_LENGTH;
> > +	u16 checksum = PMS7003_MAGIC_MSB + PMS7003_MAGIC_LSB +
> > +		       (frame->length >> 8) + (u8)frame->length +
> > +		       pms7003_calc_checksum(frame->data, offset);
> > +
> > +	return checksum == get_unaligned_be16(frame->data + offset);
> > +}
> > +
>
> The returning of 1 or 0 is not entirely obvious.  Please provide
> some documentation on what that is doing.
>
> This doesn't seem like an entirely obvious construct in general.
>
> Given we can't (I think) do anything much useful with the data until
> we get a whole frame, why not simply buffer it up unprocessed until
> we have enough data to process it in one go?
>
> On first packet dump data until you get that start markers.  After that
> wait until you have the 'header' (length) and then wait until all data
> is available keeping it in a raw buffer.
>
> A state machine that is a simple step through like this one with only
> one path ends up less readable to my eye than buffer data and
> process when all there...
>
>
> > +static int pms7003_update_frame(struct pms7003_frame *frame, u8 byte)
> > +{
> > +	switch (frame->state) {
> > +	case STATE_MAGIC_MSB:
> > +		if (byte != PMS7003_MAGIC_MSB)
> > +			return 1;
> > +		frame->state = STATE_MAGIC_LSB;
> > +		frame->length = 0;
> > +		return 1;
> > +	case STATE_MAGIC_LSB:
> > +		if (byte != PMS7003_MAGIC_LSB) {
> > +			frame->state = STATE_MAGIC_MSB;
> > +			return 1;
> > +		}
> > +		frame->state = STATE_LENGTH_MSB;
> > +		return 1;
> > +	case STATE_LENGTH_MSB:
> > +		frame->expected_length = (u16)byte << 8;
> > +		frame->state = STATE_LENGTH_LSB;
> > +		return 1;
> > +	case STATE_LENGTH_LSB:
> > +		frame->expected_length |= byte;
> > +		frame->state = STATE_DATA;
> > +		return 1;
> > +	case STATE_DATA:
> > +		if (frame->length > PMS7003_MAX_DATA_LENGTH) {
> > +			frame->state = STATE_MAGIC_MSB;
> > +			return 1;
> > +		}
> > +
> > +		frame->data[frame->length++] = byte;
> > +
> > +		if (frame->length != frame->expected_length)
> > +			return 1;
> > +
> > +		if (!pms7003_frame_okay(frame)) {
> > +			frame->state = STATE_MAGIC_MSB;
> > +			return 1;
> > +		}
> > +
> > +		frame->state = STATE_MAGIC_MSB;
> > +		break;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int pms7003_receive_buf(struct serdev_device *serdev,
> > +			       const unsigned char *buf, size_t size)
> > +{
> > +	struct iio_dev *indio_dev = serdev_device_get_drvdata(serdev);
> > +	struct pms7003_state *state = iio_priv(indio_dev);
> > +	struct pms7003_frame *frame = &state->frame;
> > +	int i, ret;
> > +
> > +	for (i = 0; i < size; i++) {
> > +		ret = pms7003_update_frame(frame, buf[i]);
> > +		if (ret)
> > +			continue;
> Given this is the normal path (continue) I would invert the
> logic to be
> 	if (!ret) {
> 		complete
> 		return..
> 	}
>
> Trivial but perhaps slightly easier to follow.
>
> > +
> > +		complete(&state->frame_ready);
> > +		return i + 1;
> > +	}
> > +
> > +	return size;
> > +}
> > +
> > +static const struct serdev_device_ops pms7003_serdev_ops = {
> > +	.receive_buf = pms7003_receive_buf,
> > +	.write_wakeup = serdev_device_write_wakeup,
> > +};
> > +
> > +static void pms7003_stop(void *data)
> > +{
> > +	struct pms7003_state *state = data;
> > +
> > +	pms7003_do_cmd(state, CMD_SLEEP);
> > +}
> > +
> > +static const unsigned long pms7003_scan_masks[] = { 0x07, 0x00 };
> > +
> > +static int pms7003_probe(struct serdev_device *serdev)
> > +{
> > +	struct pms7003_state *state;
> > +	struct iio_dev *indio_dev;
> > +	int ret;
> > +
> > +	indio_dev = devm_iio_device_alloc(&serdev->dev, sizeof(*state));
> > +	if (!indio_dev)
> > +		return -ENOMEM;
> > +
> > +	state = iio_priv(indio_dev);
> > +	serdev_device_set_drvdata(serdev, indio_dev);
> > +	state->serdev = serdev;
> > +	indio_dev->dev.parent = &serdev->dev;
> > +	indio_dev->info = &pms7003_info;
> > +	indio_dev->name = PMS7003_DRIVER_NAME;
> > +	indio_dev->channels = pms7003_channels,
> > +	indio_dev->num_channels = ARRAY_SIZE(pms7003_channels);
> > +	indio_dev->modes = INDIO_DIRECT_MODE;
> > +	indio_dev->available_scan_masks = pms7003_scan_masks;
> > +
> > +	mutex_init(&state->lock);
> > +	init_completion(&state->frame_ready);
> > +
> > +	serdev_device_set_client_ops(serdev, &pms7003_serdev_ops);
> > +	ret = devm_serdev_device_open(&serdev->dev, serdev);
> > +	if (ret)
> > +		return ret;
> > +
> > +	serdev_device_set_baudrate(serdev, 9600);
> > +	serdev_device_set_flow_control(serdev, false);
> > +
> > +	ret = serdev_device_set_parity(serdev, SERDEV_PARITY_NONE);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = pms7003_do_cmd(state, CMD_WAKEUP);
> > +	if (ret) {
> > +		dev_err(&serdev->dev, "failed to wakeup sensor\n");
> > +		return ret;
> > +	}
> > +
> > +	ret = pms7003_do_cmd(state, CMD_ENTER_PASSIVE_MODE);
> > +	if (ret) {
> > +		dev_err(&serdev->dev, "failed to enter passive mode\n");
> > +		return ret;
> > +	}
> > +
> > +	ret = devm_add_action_or_reset(&serdev->dev, pms7003_stop, state);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = devm_iio_triggered_buffer_setup(&serdev->dev, indio_dev, NULL,
> > +					      pms7003_trigger_handler, NULL);
> > +	if (ret)
> > +		return ret;
> > +
> > +	return devm_iio_device_register(&serdev->dev, indio_dev);
> > +}
> > +
> > +static const struct of_device_id pms7003_of_match[] = {
> > +	{ .compatible = "plantower,pms7003" },
> > +	{ }
> > +};
> > +MODULE_DEVICE_TABLE(of, pms7003_of_match);
> > +
> > +static struct serdev_device_driver pms7003_driver = {
> > +	.driver = {
> > +		.name = PMS7003_DRIVER_NAME,
> > +		.of_match_table = pms7003_of_match,
> > +	},
> > +	.probe = pms7003_probe,
> > +};
> > +module_serdev_device_driver(pms7003_driver);
> > +
> > +MODULE_AUTHOR("Tomasz Duszynski <tduszyns@gmail.com>");
> > +MODULE_DESCRIPTION("Plantower PMS7003 particulate matter sensor driver");
> > +MODULE_LICENSE("GPL v2");
>

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH 3/3] dt-bindings: iio: chemical: pms7003: add device tree support
  2019-01-11 22:15   ` Rob Herring
@ 2019-01-27 13:45     ` Tomasz Duszynski
  0 siblings, 0 replies; 11+ messages in thread
From: Tomasz Duszynski @ 2019-01-27 13:45 UTC (permalink / raw)
  To: Rob Herring; +Cc: Tomasz Duszynski, linux-iio, linux-kernel, devicetree

On Fri, Jan 11, 2019 at 04:15:26PM -0600, Rob Herring wrote:
> On Sun, Jan 06, 2019 at 06:16:14PM +0100, Tomasz Duszynski wrote:
> > Add device tree support for Plantower PMS7003 particulate matter sensor.
> >
> > Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
> > ---
> >  .../bindings/iio/chemical/plantower,pms7003.txt    | 14 ++++++++++++++
> >  1 file changed, 14 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
> >
> > diff --git a/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
> > new file mode 100644
> > index 000000000000..79eb538eb932
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.txt
> > @@ -0,0 +1,14 @@
> > +* Plantower PMS7003 particulate matter sensor
> > +
> > +Required properties:
> > +- compatible: must be "plantower,pms7003"
>
> Looks like this has reset and set GPIO lines as well as Vcc supply.
> Bindings should be complete even if the driver or a platform doesn't use
> some parts.
>

Fine. I'll add missing pin descriptions in v2 then.

> > +
> > +Refer to serial/slave-device.txt for generic serial attached device bindings.
> > +
> > +Example:
> > +
> > +&uart@0 {
> > +	pms7003 {
> > +		compatible = "plantower,pms7003";
> > +	};
> > +};
> > --
> > 2.20.1
> >

^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, back to index

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-01-06 17:16 [PATCH 0/3] add support for PMS7003 PM sensor Tomasz Duszynski
2019-01-06 17:16 ` [PATCH 1/3] iio: chemical: add support for Plantower PMS7003 sensor Tomasz Duszynski
2019-01-07 15:35   ` Johan Hovold
2019-01-08 19:07     ` Tomasz Duszynski
2019-01-12 17:48   ` Jonathan Cameron
2019-01-23 21:08     ` Tomasz Duszynski
2019-01-06 17:16 ` [PATCH 2/3] dt-bindings: add Plantower to the vendor prefixes Tomasz Duszynski
2019-01-11 22:12   ` Rob Herring
2019-01-06 17:16 ` [PATCH 3/3] dt-bindings: iio: chemical: pms7003: add device tree support Tomasz Duszynski
2019-01-11 22:15   ` Rob Herring
2019-01-27 13:45     ` Tomasz Duszynski

Linux-IIO Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-iio/0 linux-iio/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-iio linux-iio/ https://lore.kernel.org/linux-iio \
		linux-iio@vger.kernel.org linux-iio@archiver.kernel.org
	public-inbox-index linux-iio


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-iio


AGPL code for this site: git clone https://public-inbox.org/ public-inbox