On Jun 18, Sean Nyekjaer wrote:
> 
> 
> On 18/06/2019 17.55, Lorenzo Bianconi wrote:
> > > The interrupt source can come from multiple sources, fifo and wake interrupts.
> > > Enter interrupt thread to check which interrupt that has fired.
> > > 
> > > Signed-off-by: Sean Nyekjaer <sean@geanix.com>
> > > ---
> > >   drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 30 +++++++++++++++-----
> > >   1 file changed, 23 insertions(+), 7 deletions(-)
> > > 
> > > diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
> > > index 59a34894e495..76aec5024d83 100644
> > > --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
> > > +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
> > > @@ -78,6 +78,12 @@
> > >   #define ST_LSM6DSX_REG_GYRO_OUT_Y_L_ADDR	0x24
> > >   #define ST_LSM6DSX_REG_GYRO_OUT_Z_L_ADDR	0x26
> > > +#define ST_LSM6DSX_REG_WAKE_UP_SRC_ADDR		0x1B
> > > +#define ST_LSM6DSX_REG_WAKE_UP_SRC_Z_WU_MASK	BIT(0)
> > > +#define ST_LSM6DSX_REG_WAKE_UP_SRC_Y_WU_MASK	BIT(1)
> > > +#define ST_LSM6DSX_REG_WAKE_UP_SRC_X_WU_MASK	BIT(2)
> > > +#define ST_LSM6DSX_REG_WAKE_UP_SRC_WU_MASK	BIT(4)
> > > +
> > >   #define ST_LSM6DSX_REG_TAP_CFG_ADDR		0x58
> > >   #define ST_LSM6DSX_REG_TAP_CFG_INT_EN_MASK	BIT(7)
> > >   #define ST_LSM6DSX_REG_TAP_CFG_INACT_EN_MASK	GENMASK(6, 5)
> > > @@ -946,19 +952,29 @@ int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw)
> > >   static irqreturn_t st_lsm6dsx_handler_irq(int irq, void *private)
> > >   {
> > > -	struct st_lsm6dsx_hw *hw = private;
> > > -
> > > -	return hw->sip > 0 ? IRQ_WAKE_THREAD : IRQ_NONE;
> > > +	return IRQ_WAKE_THREAD;
> > 
> > I guess this will break shared interrupt, isn't it?
> 
> When you write shared interrupt you mean: the drdy-int-pin stuff?
> I need to add so we can use all this functionality with the INT2 as well...

nope, shared IRQ line with other devices (when you set drive-open-drain dts
property)

> 
> > 
> > >   }
> > >   static irqreturn_t st_lsm6dsx_handler_thread(int irq, void *private)
> > >   {
> > >   	struct st_lsm6dsx_hw *hw = private;
> > > -	int count;
> > > +	int count = 0;
> > > +	int data, err;
> > > +
> > > +	if (hw->enable_event) {
> > > +		err = regmap_read(hw->regmap,
> > > +				  ST_LSM6DSX_REG_WAKE_UP_SRC_ADDR, &data);
> > > +		if (err < 0)
> > > +			goto try_fifo;
> > 
> > You can simplify this just doing something like:
> > 
> > 		if (err < 0 && !hw->sip)
> > 			return IRQ_NONE;
> > 
> Will apply :-)
> 
> Thanks for the review Lorenzo...

Thanks for working on this :)

Regards,
Lorenzo

> 
> -- 
> Best regards,
> Sean Nyekjær
> Embedded Linux Consultant
> 
> +45 42427326
> sean@geanix.com
> 
> Geanix ApS
> https://geanix.com
> DK39600706