From: Martin Kepplinger <martin.kepplinger@puri.sm>
To: lorenzo.bianconi83@gmail.com, jic23@kernel.org, knaack.h@gmx.de,
lars@metafoo.de, pmeerw@pmeerw.net
Cc: linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Martin Kepplinger <martin.kepplinger@puri.sm>
Subject: [PATCHv2 2/3] iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9sd1
Date: Tue, 16 Jul 2019 11:33:24 +0200 [thread overview]
Message-ID: <20190716093325.7683-2-martin.kepplinger@puri.sm> (raw)
In-Reply-To: <20190716093325.7683-1-martin.kepplinger@puri.sm>
The LSM9DS1's accelerometer / gyroscope unit and it's magnetometer (separately
supported in iio/magnetometer/st_magn*) are located on a separate i2c addresses
on the bus.
For the datasheet, see https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Treat it just like the LSM6* devices and, despite it's name, hook it up
to the st_lsm6dsx driver, using it's basic functionality.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
---
This is already based on Lorenzo's recent changes:
https://lore.kernel.org/linux-iio/853f216a-7814-cb79-180b-078ac5e8a359@puri.sm/T/#u
https://lore.kernel.org/linux-iio/501b0db9-63cb-905c-c09b-682eb73f1ff3@puri.sm/T/#u
revision history:
v2: overall further simplification
thanks
martin
drivers/iio/imu/st_lsm6dsx/Kconfig | 1 +
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 2 +
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 94 +++++++++++++++++++-
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c | 5 ++
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c | 5 ++
5 files changed, 104 insertions(+), 3 deletions(-)
diff --git a/drivers/iio/imu/st_lsm6dsx/Kconfig b/drivers/iio/imu/st_lsm6dsx/Kconfig
index 2d8b2e1edfce..4a57bfb3c12e 100644
--- a/drivers/iio/imu/st_lsm6dsx/Kconfig
+++ b/drivers/iio/imu/st_lsm6dsx/Kconfig
@@ -11,6 +11,7 @@ config IIO_ST_LSM6DSX
Say yes here to build support for STMicroelectronics LSM6DSx imu
sensor. Supported devices: lsm6ds3, lsm6ds3h, lsm6dsl, lsm6dsm,
ism330dlc, lsm6dso, lsm6dsox, asm330lhh, lsm6dsr, lsm6ds3tr-c
+ and the accelerometer/gyroscope of lsm9ds1.
To compile this driver as a module, choose M here: the module
will be called st_lsm6dsx.
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
index 3c47f5d27d30..9a30cc717de2 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
@@ -23,6 +23,7 @@
#define ST_LSM6DSOX_DEV_NAME "lsm6dsox"
#define ST_LSM6DSR_DEV_NAME "lsm6dsr"
#define ST_LSM6DS3TRC_DEV_NAME "lsm6ds3tr-c"
+#define ST_LSM9DS1_DEV_NAME "lsm9ds1"
enum st_lsm6dsx_hw_id {
ST_LSM6DS3_ID,
@@ -35,6 +36,7 @@ enum st_lsm6dsx_hw_id {
ST_LSM6DSOX_ID,
ST_LSM6DSR_ID,
ST_LSM6DS3TRC_ID,
+ ST_LSM9DS1_ID,
ST_LSM6DSX_MAX_ID,
};
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
index e0d2149625cc..2f3d2bf25646 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
@@ -10,6 +10,8 @@
* +-125/+-245/+-500/+-1000/+-2000 dps
* LSM6DSx series has an integrated First-In-First-Out (FIFO) buffer
* allowing dynamic batching of sensor data.
+ * LSM9DSx series is similar but includes an additional magnetometer, handled
+ * by a different driver.
*
* Supported sensors:
* - LSM6DS3:
@@ -30,6 +32,13 @@
* - Gyroscope supported full-scale [dps]: +-125/+-245/+-500/+-1000/+-2000
* - FIFO size: 3KB
*
+ * - LSM9DS1:
+ * - Accelerometer supported ODR [Hz]: 10, 50, 119, 238, 476, 952
+ * - Accelerometer supported full-scale [g]: +-2/+-4/+-8/+-16
+ * - Gyroscope supported ODR [Hz]: 15, 60, 119, 238, 476, 952
+ * - Gyroscope supported full-scale [dps]: +-245/+-500/+-2000
+ * - FIFO size: 32
+ *
* Copyright 2016 STMicroelectronics Inc.
*
* Lorenzo Bianconi <lorenzo.bianconi@st.com>
@@ -64,7 +73,72 @@
#define ST_LSM6DSX_REG_GYRO_OUT_Y_L_ADDR 0x24
#define ST_LSM6DSX_REG_GYRO_OUT_Z_L_ADDR 0x26
+#define ST_LSM9DSX_REG_GYRO_OUT_X_L_ADDR 0x18
+#define ST_LSM9DSX_REG_GYRO_OUT_Y_L_ADDR 0x1a
+#define ST_LSM9DSX_REG_GYRO_OUT_Z_L_ADDR 0x1c
+
static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
+ {
+ .wai = 0x68,
+ .int1_addr = 0x0c,
+ .int2_addr = 0x0d,
+ .reset_addr = 0x22,
+ .max_fifo_size = 32,
+ .id = {
+ {
+ .hw_id = ST_LSM9DS1_ID,
+ .name = ST_LSM9DS1_DEV_NAME,
+ },
+ },
+ .odr_table = {
+ [ST_LSM6DSX_ID_ACC] = {
+ .reg = {
+ .addr = 0x20,
+ .mask = GENMASK(7, 5),
+ },
+ .odr_avl[0] = { 10, 0x01 },
+ .odr_avl[1] = { 50, 0x02 },
+ .odr_avl[2] = { 119, 0x03 },
+ .odr_avl[3] = { 238, 0x04 },
+ .odr_avl[4] = { 476, 0x05 },
+ .odr_avl[5] = { 952, 0x06 },
+ },
+ [ST_LSM6DSX_ID_GYRO] = {
+ .reg = {
+ .addr = 0x10,
+ .mask = GENMASK(7, 5),
+ },
+ .odr_avl[0] = { 15, 0x01 },
+ .odr_avl[1] = { 60, 0x02 },
+ .odr_avl[2] = { 119, 0x03 },
+ .odr_avl[3] = { 238, 0x04 },
+ .odr_avl[4] = { 476, 0x05 },
+ .odr_avl[5] = { 952, 0x06 },
+ },
+ },
+ .fs_table = {
+ [ST_LSM6DSX_ID_ACC] = {
+ .reg = {
+ .addr = 0x20,
+ .mask = GENMASK(4, 3),
+ },
+ .fs_avl[0] = { 599, 0x0 },
+ .fs_avl[1] = { 1197, 0x2 },
+ .fs_avl[2] = { 2394, 0x3 },
+ .fs_avl[3] = { 4788, 0x1 },
+ },
+ [ST_LSM6DSX_ID_GYRO] = {
+ .reg = {
+ .addr = 0x10,
+ .mask = GENMASK(4, 3),
+ },
+ .fs_avl[0] = { IIO_DEGREE_TO_RAD(245), 0x0 },
+ .fs_avl[1] = { IIO_DEGREE_TO_RAD(500), 0x1 },
+ .fs_avl[2] = { IIO_DEGREE_TO_RAD(0), 0x2 },
+ .fs_avl[3] = { IIO_DEGREE_TO_RAD(2000), 0x3 },
+ },
+ },
+ },
{
.wai = 0x69,
.int1_addr = 0x0d,
@@ -733,6 +807,16 @@ static const struct iio_chan_spec st_lsm6dsx_gyro_channels[] = {
IIO_CHAN_SOFT_TIMESTAMP(3),
};
+static const struct iio_chan_spec st_lsm9dsx_gyro_channels[] = {
+ ST_LSM6DSX_CHANNEL(IIO_ANGL_VEL, ST_LSM9DSX_REG_GYRO_OUT_X_L_ADDR,
+ IIO_MOD_X, 0),
+ ST_LSM6DSX_CHANNEL(IIO_ANGL_VEL, ST_LSM9DSX_REG_GYRO_OUT_Y_L_ADDR,
+ IIO_MOD_Y, 1),
+ ST_LSM6DSX_CHANNEL(IIO_ANGL_VEL, ST_LSM9DSX_REG_GYRO_OUT_Z_L_ADDR,
+ IIO_MOD_Z, 2),
+ IIO_CHAN_SOFT_TIMESTAMP(3),
+};
+
int st_lsm6dsx_set_page(struct st_lsm6dsx_hw *hw, bool enable)
{
const struct st_lsm6dsx_shub_settings *hub_settings;
@@ -1278,7 +1362,7 @@ static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw)
static struct iio_dev *st_lsm6dsx_alloc_iiodev(struct st_lsm6dsx_hw *hw,
enum st_lsm6dsx_sensor_id id,
- const char *name)
+ const char *name, int hw_id)
{
struct st_lsm6dsx_sensor *sensor;
struct iio_dev *iio_dev;
@@ -1308,7 +1392,11 @@ static struct iio_dev *st_lsm6dsx_alloc_iiodev(struct st_lsm6dsx_hw *hw,
name);
break;
case ST_LSM6DSX_ID_GYRO:
- iio_dev->channels = st_lsm6dsx_gyro_channels;
+ if (hw_id == ST_LSM9DS1_ID)
+ iio_dev->channels = st_lsm9dsx_gyro_channels;
+ else
+ iio_dev->channels = st_lsm6dsx_gyro_channels;
+
iio_dev->num_channels = ARRAY_SIZE(st_lsm6dsx_gyro_channels);
iio_dev->info = &st_lsm6dsx_gyro_info;
@@ -1354,7 +1442,7 @@ int st_lsm6dsx_probe(struct device *dev, int irq, int hw_id,
return err;
for (i = 0; i < ST_LSM6DSX_ID_EXT0; i++) {
- hw->iio_devs[i] = st_lsm6dsx_alloc_iiodev(hw, i, name);
+ hw->iio_devs[i] = st_lsm6dsx_alloc_iiodev(hw, i, name, hw_id);
if (!hw->iio_devs[i])
return -ENOMEM;
}
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c
index 28581eb0532c..c36a057c36ee 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c
@@ -79,6 +79,10 @@ static const struct of_device_id st_lsm6dsx_i2c_of_match[] = {
.compatible = "st,lsm6ds3tr-c",
.data = (void *)ST_LSM6DS3TRC_ID,
},
+ {
+ .compatible = "st,lsm9ds1",
+ .data = (void *)ST_LSM9DS1_ID,
+ },
{},
};
MODULE_DEVICE_TABLE(of, st_lsm6dsx_i2c_of_match);
@@ -94,6 +98,7 @@ static const struct i2c_device_id st_lsm6dsx_i2c_id_table[] = {
{ ST_LSM6DSOX_DEV_NAME, ST_LSM6DSOX_ID },
{ ST_LSM6DSR_DEV_NAME, ST_LSM6DSR_ID },
{ ST_LSM6DS3TRC_DEV_NAME, ST_LSM6DS3TRC_ID },
+ { ST_LSM9DS1_DEV_NAME, ST_LSM9DS1_ID },
{},
};
MODULE_DEVICE_TABLE(i2c, st_lsm6dsx_i2c_id_table);
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c
index 0371e8b94a3e..138e3b985865 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c
@@ -79,6 +79,10 @@ static const struct of_device_id st_lsm6dsx_spi_of_match[] = {
.compatible = "st,lsm6ds3tr-c",
.data = (void *)ST_LSM6DS3TRC_ID,
},
+ {
+ .compatible = "st,lsm9ds1",
+ .data = (void *)ST_LSM9DS1_ID,
+ },
{},
};
MODULE_DEVICE_TABLE(of, st_lsm6dsx_spi_of_match);
@@ -94,6 +98,7 @@ static const struct spi_device_id st_lsm6dsx_spi_id_table[] = {
{ ST_LSM6DSOX_DEV_NAME, ST_LSM6DSOX_ID },
{ ST_LSM6DSR_DEV_NAME, ST_LSM6DSR_ID },
{ ST_LSM6DS3TRC_DEV_NAME, ST_LSM6DS3TRC_ID },
+ { ST_LSM9DS1_DEV_NAME, ST_LSM9DS1_ID },
{},
};
MODULE_DEVICE_TABLE(spi, st_lsm6dsx_spi_id_table);
--
2.20.1
next prev parent reply other threads:[~2019-07-16 9:34 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-07-16 9:33 [PATCHv2 1/3] iio: imu: st_lsm6sdx: move register definitions to sensor_settings struct Martin Kepplinger
2019-07-16 9:33 ` Martin Kepplinger [this message]
2019-07-16 9:48 ` [PATCHv2 2/3] iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9sd1 Lorenzo Bianconi
2019-07-16 9:33 ` [PATCH 3/3] dt-bindings: iio: imu: st_lsm6dsx: add lsm9ds1 device bindings Martin Kepplinger
2019-07-16 9:43 ` [PATCHv2 1/3] iio: imu: st_lsm6sdx: move register definitions to sensor_settings struct Lorenzo Bianconi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190716093325.7683-2-martin.kepplinger@puri.sm \
--to=martin.kepplinger@puri.sm \
--cc=devicetree@vger.kernel.org \
--cc=jic23@kernel.org \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lorenzo.bianconi83@gmail.com \
--cc=pmeerw@pmeerw.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).