linux-iio.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
@ 2019-03-26 14:51 Andy Shevchenko
  2019-03-30 15:31 ` Jonathan Cameron
  0 siblings, 1 reply; 8+ messages in thread
From: Andy Shevchenko @ 2019-03-26 14:51 UTC (permalink / raw)
  To: Jonathan Cameron, Hartmut Knaack, Lars-Peter Clausen,
	Peter Meerwald-Stadler, linux-iio, Vincent Pelletier,
	Tomasz Duszynski
  Cc: Andy Shevchenko

From: Vincent Pelletier <plr.vincent@gmail.com>

Exposes the ADC device present on, at least, Intel Merrifield platform.

Based on work done by:
  Yang Bin <bin.yang@intel.com>
  Huiquan Zhong <huiquan.zhong@intel.com>
  Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
  Pavan Kumar S <pavan.kumar.s@intel.com>

Though it has been heavily rewritten for upstream.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
- reordered headers, dependent on the patch against iio/driver.h (Jonathan, Tomasz)
- dropped buffer dead code (Tomasz)
- used get_unaligned_be16() (Tomasz)
- replaced iio_device_{claim,release}_direct_mode by mutex (Tomasz)
- COMPILE_TEST is not included due to implicit x86 requirement anyway (via MFD)

 drivers/iio/adc/Kconfig           |  11 ++
 drivers/iio/adc/Makefile          |   1 +
 drivers/iio/adc/intel_mrfld_adc.c | 262 ++++++++++++++++++++++++++++++
 3 files changed, 274 insertions(+)
 create mode 100644 drivers/iio/adc/intel_mrfld_adc.c

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 76db6e5cc296..88b06393d152 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -419,6 +419,17 @@ config INGENIC_ADC
 	  This driver can also be built as a module. If so, the module will be
 	  called ingenic_adc.
 
+config INTEL_MRFLD_ADC
+	tristate "Intel Merrifield Basin Cove ADC driver"
+	depends on INTEL_SOC_PMIC_MRFLD
+	help
+	  Say yes here to have support for Basin Cove power management IC (PMIC) ADC
+	  device. Depending on platform configuration, this general purpose ADC can
+	  be used for sampling sensors such as thermal resistors.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called intel_mrfld_adc.
+
 config IMX7D_ADC
 	tristate "Freescale IMX7D ADC driver"
 	depends on ARCH_MXC || COMPILE_TEST
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 6fcebd167524..6cbf2e5a51a7 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_HX711) += hx711.o
 obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
 obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
 obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o
+obj-$(CONFIG_INTEL_MRFLD_ADC) += intel_mrfld_adc.o
 obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
 obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o
 obj-$(CONFIG_LPC32XX_ADC) += lpc32xx_adc.o
diff --git a/drivers/iio/adc/intel_mrfld_adc.c b/drivers/iio/adc/intel_mrfld_adc.c
new file mode 100644
index 000000000000..67d096f8180d
--- /dev/null
+++ b/drivers/iio/adc/intel_mrfld_adc.c
@@ -0,0 +1,262 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ADC driver for Basin Cove PMIC
+ *
+ * Copyright (C) 2012 Intel Corporation
+ * Author: Bin Yang <bin.yang@intel.com>
+ *
+ * Rewritten for upstream by:
+ *	 Vincent Pelletier <plr.vincent@gmail.com>
+ *	 Andy Shevchenko <andriy.shevchenko@linux.intel.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/completion.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/mfd/intel_soc_pmic_mrfld.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <linux/iio/driver.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/machine.h>
+
+#include <asm/unaligned.h>
+
+#define BCOVE_GPADCREQ			0xDC
+#define BCOVE_GPADCREQ_BUSY		BIT(0)
+#define BCOVE_GPADCREQ_IRQEN		BIT(1)
+
+#define BCOVE_ADCIRQ_ALL (		\
+	BCOVE_ADCIRQ_BATTEMP |		\
+	BCOVE_ADCIRQ_SYSTEMP |		\
+	BCOVE_ADCIRQ_BATTID |		\
+	BCOVE_ADCIRQ_VIBATT |		\
+	BCOVE_ADCIRQ_CCTICK)
+
+#define BCOVE_ADC_TIMEOUT		msecs_to_jiffies(1000)
+
+static const u8 mrfld_adc_requests[] = {
+	BCOVE_ADCIRQ_VIBATT,
+	BCOVE_ADCIRQ_BATTID,
+	BCOVE_ADCIRQ_VIBATT,
+	BCOVE_ADCIRQ_SYSTEMP,
+	BCOVE_ADCIRQ_BATTEMP,
+	BCOVE_ADCIRQ_BATTEMP,
+	BCOVE_ADCIRQ_SYSTEMP,
+	BCOVE_ADCIRQ_SYSTEMP,
+	BCOVE_ADCIRQ_SYSTEMP,
+};
+
+struct mrfld_adc {
+	struct regmap *regmap;
+	struct completion completion;
+	/* Lock to protect the IPC transfers */
+	struct mutex lock;
+};
+
+static irqreturn_t mrfld_adc_thread_isr(int irq, void *data)
+{
+	struct iio_dev *indio_dev = data;
+	struct mrfld_adc *adc = iio_priv(indio_dev);
+
+	complete(&adc->completion);
+	return IRQ_HANDLED;
+}
+
+static int mrfld_adc_single_conv(struct iio_dev *indio_dev,
+				 struct iio_chan_spec const *chan,
+				 int *result)
+{
+	struct mrfld_adc *adc = iio_priv(indio_dev);
+	struct regmap *regmap = adc->regmap;
+	unsigned int req;
+	long timeout;
+	u8 buf[2];
+	int ret;
+
+	reinit_completion(&adc->completion);
+
+	regmap_update_bits(regmap, BCOVE_MADCIRQ, BCOVE_ADCIRQ_ALL, 0);
+	regmap_update_bits(regmap, BCOVE_MIRQLVL1, BCOVE_LVL1_ADC, 0);
+
+	ret = regmap_read_poll_timeout(regmap, BCOVE_GPADCREQ, req,
+				       !(req & BCOVE_GPADCREQ_BUSY),
+				       2000, 1000000);
+	if (ret)
+		goto done;
+
+	req = mrfld_adc_requests[chan->channel];
+	ret = regmap_write(regmap, BCOVE_GPADCREQ, BCOVE_GPADCREQ_IRQEN | req);
+	if (ret)
+		goto done;
+
+	timeout = wait_for_completion_interruptible_timeout(&adc->completion,
+							    BCOVE_ADC_TIMEOUT);
+	if (timeout < 0) {
+		ret = timeout;
+		goto done;
+	}
+	if (timeout == 0) {
+		ret = -ETIMEDOUT;
+		goto done;
+	}
+
+	ret = regmap_bulk_read(regmap, chan->address, buf, 2);
+	if (ret)
+		goto done;
+
+	*result = get_unaligned_be16(buf);
+	ret = IIO_VAL_INT;
+
+done:
+	regmap_update_bits(regmap, BCOVE_MIRQLVL1, BCOVE_LVL1_ADC, 0xff);
+	regmap_update_bits(regmap, BCOVE_MADCIRQ, BCOVE_ADCIRQ_ALL, 0xff);
+
+	return ret;
+}
+
+static int mrfld_adc_read_raw(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *chan,
+			      int *val, int *val2, long mask)
+{
+	struct mrfld_adc *adc = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&adc->lock);
+		ret = mrfld_adc_single_conv(indio_dev, chan, val);
+		mutex_unlock(&adc->lock);
+		return ret;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_info mrfld_adc_iio_info = {
+	.read_raw = &mrfld_adc_read_raw,
+};
+
+#define BCOVE_ADC_CHANNEL(_type, _channel, _datasheet_name, _address)	\
+	{								\
+		.indexed = 1,						\
+		.type = _type,						\
+		.channel = _channel,					\
+		.address = _address,					\
+		.datasheet_name = _datasheet_name,			\
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	}
+
+static const struct iio_chan_spec mrfld_adc_channels[] = {
+	BCOVE_ADC_CHANNEL(IIO_VOLTAGE,    0, "CH0", 0xE9),
+	BCOVE_ADC_CHANNEL(IIO_RESISTANCE, 1, "CH1", 0xEB),
+	BCOVE_ADC_CHANNEL(IIO_CURRENT,    2, "CH2", 0xED),
+	BCOVE_ADC_CHANNEL(IIO_TEMP,       3, "CH3", 0xCC),
+	BCOVE_ADC_CHANNEL(IIO_TEMP,       4, "CH4", 0xC8),
+	BCOVE_ADC_CHANNEL(IIO_TEMP,       5, "CH5", 0xCA),
+	BCOVE_ADC_CHANNEL(IIO_TEMP,       6, "CH6", 0xC2),
+	BCOVE_ADC_CHANNEL(IIO_TEMP,       7, "CH7", 0xC4),
+	BCOVE_ADC_CHANNEL(IIO_TEMP,       8, "CH8", 0xC6),
+};
+
+static struct iio_map iio_maps[] = {
+	IIO_MAP("CH0", "bcove-battery", "VBATRSLT"),
+	IIO_MAP("CH1", "bcove-battery", "BATTID"),
+	IIO_MAP("CH2", "bcove-battery", "IBATRSLT"),
+	IIO_MAP("CH3", "bcove-temp",    "PMICTEMP"),
+	IIO_MAP("CH4", "bcove-temp",    "BATTEMP0"),
+	IIO_MAP("CH5", "bcove-temp",    "BATTEMP1"),
+	IIO_MAP("CH6", "bcove-temp",    "SYSTEMP0"),
+	IIO_MAP("CH7", "bcove-temp",    "SYSTEMP1"),
+	IIO_MAP("CH8", "bcove-temp",    "SYSTEMP2"),
+	{}
+};
+
+static int mrfld_adc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct intel_soc_pmic *pmic = dev_get_drvdata(dev->parent);
+	struct iio_dev *indio_dev;
+	struct mrfld_adc *adc;
+	int irq;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*indio_dev));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	adc = iio_priv(indio_dev);
+
+	mutex_init(&adc->lock);
+	init_completion(&adc->completion);
+	adc->regmap = pmic->regmap;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	ret = devm_request_threaded_irq(dev, irq, NULL, mrfld_adc_thread_isr,
+					IRQF_ONESHOT | IRQF_SHARED, pdev->name,
+					indio_dev);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, indio_dev);
+
+	indio_dev->dev.parent = dev;
+	indio_dev->name = pdev->name;
+
+	indio_dev->channels = mrfld_adc_channels;
+	indio_dev->num_channels = ARRAY_SIZE(mrfld_adc_channels);
+	indio_dev->info = &mrfld_adc_iio_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	ret = iio_map_array_register(indio_dev, iio_maps);
+	if (ret)
+		return ret;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret < 0)
+		goto err_array_unregister;
+
+	return 0;
+
+err_array_unregister:
+	iio_map_array_unregister(indio_dev);
+	return ret;
+}
+
+static int mrfld_adc_remove(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+
+	iio_map_array_unregister(indio_dev);
+
+	return 0;
+}
+
+static const struct platform_device_id mrfld_adc_id_table[] = {
+	{ .name = "mrfld_bcove_adc" },
+	{}
+};
+MODULE_DEVICE_TABLE(platform, mrfld_adc_id_table);
+
+static struct platform_driver mrfld_adc_driver = {
+	.driver = {
+		.name = "mrfld_bcove_adc",
+	},
+	.probe = mrfld_adc_probe,
+	.remove = mrfld_adc_remove,
+	.id_table = mrfld_adc_id_table,
+};
+module_platform_driver(mrfld_adc_driver);
+
+MODULE_AUTHOR("Bin Yang <bin.yang@intel.com>");
+MODULE_AUTHOR("Vincent Pelletier <plr.vincent@gmail.com>");
+MODULE_AUTHOR("Andy Shevchenko <andriy.shevchenko@linux.intel.com>");
+MODULE_DESCRIPTION("ADC driver for Basin Cove PMIC");
+MODULE_LICENSE("GPL v2");
-- 
2.20.1


^ permalink raw reply related	[flat|nested] 8+ messages in thread

* Re: [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
  2019-03-26 14:51 [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver Andy Shevchenko
@ 2019-03-30 15:31 ` Jonathan Cameron
  2019-09-02 13:13   ` Andy Shevchenko
  0 siblings, 1 reply; 8+ messages in thread
From: Jonathan Cameron @ 2019-03-30 15:31 UTC (permalink / raw)
  To: Andy Shevchenko
  Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
	linux-iio, Vincent Pelletier, Tomasz Duszynski

On Tue, 26 Mar 2019 16:51:38 +0200
Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:

> From: Vincent Pelletier <plr.vincent@gmail.com>
> 
> Exposes the ADC device present on, at least, Intel Merrifield platform.
> 
> Based on work done by:
>   Yang Bin <bin.yang@intel.com>
>   Huiquan Zhong <huiquan.zhong@intel.com>
>   Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
>   Pavan Kumar S <pavan.kumar.s@intel.com>
> 
> Though it has been heavily rewritten for upstream.
> 
> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Hmm. There is a very small ordering issue in probe vs remove, which
I'll probably just fix up.

However I don't yet have the header in my upstream so will wait
until that is there before applying.  If Lee or whoever is dealing
with that patch set puts out an immutable branch with it in then
let me know.

Give me a poke if I seem to have forgotten it.

thanks,

Jonathan

> ---
> - reordered headers, dependent on the patch against iio/driver.h (Jonathan, Tomasz)
> - dropped buffer dead code (Tomasz)
> - used get_unaligned_be16() (Tomasz)
> - replaced iio_device_{claim,release}_direct_mode by mutex (Tomasz)
> - COMPILE_TEST is not included due to implicit x86 requirement anyway (via MFD)
> 
>  drivers/iio/adc/Kconfig           |  11 ++
>  drivers/iio/adc/Makefile          |   1 +
>  drivers/iio/adc/intel_mrfld_adc.c | 262 ++++++++++++++++++++++++++++++
>  3 files changed, 274 insertions(+)
>  create mode 100644 drivers/iio/adc/intel_mrfld_adc.c
> 
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 76db6e5cc296..88b06393d152 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -419,6 +419,17 @@ config INGENIC_ADC
>  	  This driver can also be built as a module. If so, the module will be
>  	  called ingenic_adc.
>  
> +config INTEL_MRFLD_ADC
> +	tristate "Intel Merrifield Basin Cove ADC driver"
> +	depends on INTEL_SOC_PMIC_MRFLD
> +	help
> +	  Say yes here to have support for Basin Cove power management IC (PMIC) ADC
> +	  device. Depending on platform configuration, this general purpose ADC can
> +	  be used for sampling sensors such as thermal resistors.
> +
> +	  To compile this driver as a module, choose M here: the module will be
> +	  called intel_mrfld_adc.
> +
>  config IMX7D_ADC
>  	tristate "Freescale IMX7D ADC driver"
>  	depends on ARCH_MXC || COMPILE_TEST
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 6fcebd167524..6cbf2e5a51a7 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -41,6 +41,7 @@ obj-$(CONFIG_HX711) += hx711.o
>  obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
>  obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
>  obj-$(CONFIG_INGENIC_ADC) += ingenic-adc.o
> +obj-$(CONFIG_INTEL_MRFLD_ADC) += intel_mrfld_adc.o
>  obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
>  obj-$(CONFIG_LPC18XX_ADC) += lpc18xx_adc.o
>  obj-$(CONFIG_LPC32XX_ADC) += lpc32xx_adc.o
> diff --git a/drivers/iio/adc/intel_mrfld_adc.c b/drivers/iio/adc/intel_mrfld_adc.c
> new file mode 100644
> index 000000000000..67d096f8180d
> --- /dev/null
> +++ b/drivers/iio/adc/intel_mrfld_adc.c
> @@ -0,0 +1,262 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * ADC driver for Basin Cove PMIC
> + *
> + * Copyright (C) 2012 Intel Corporation
> + * Author: Bin Yang <bin.yang@intel.com>
> + *
> + * Rewritten for upstream by:
> + *	 Vincent Pelletier <plr.vincent@gmail.com>
> + *	 Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/completion.h>
> +#include <linux/interrupt.h>
> +#include <linux/mfd/intel_soc_pmic.h>
> +#include <linux/mfd/intel_soc_pmic_mrfld.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include <linux/iio/driver.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/machine.h>
> +
> +#include <asm/unaligned.h>
> +
> +#define BCOVE_GPADCREQ			0xDC
> +#define BCOVE_GPADCREQ_BUSY		BIT(0)
> +#define BCOVE_GPADCREQ_IRQEN		BIT(1)
> +
> +#define BCOVE_ADCIRQ_ALL (		\
> +	BCOVE_ADCIRQ_BATTEMP |		\
> +	BCOVE_ADCIRQ_SYSTEMP |		\
> +	BCOVE_ADCIRQ_BATTID |		\
> +	BCOVE_ADCIRQ_VIBATT |		\
> +	BCOVE_ADCIRQ_CCTICK)
> +
> +#define BCOVE_ADC_TIMEOUT		msecs_to_jiffies(1000)
> +
> +static const u8 mrfld_adc_requests[] = {
> +	BCOVE_ADCIRQ_VIBATT,
> +	BCOVE_ADCIRQ_BATTID,
> +	BCOVE_ADCIRQ_VIBATT,
> +	BCOVE_ADCIRQ_SYSTEMP,
> +	BCOVE_ADCIRQ_BATTEMP,
> +	BCOVE_ADCIRQ_BATTEMP,
> +	BCOVE_ADCIRQ_SYSTEMP,
> +	BCOVE_ADCIRQ_SYSTEMP,
> +	BCOVE_ADCIRQ_SYSTEMP,
> +};
> +
> +struct mrfld_adc {
> +	struct regmap *regmap;
> +	struct completion completion;
> +	/* Lock to protect the IPC transfers */
> +	struct mutex lock;
> +};
> +
> +static irqreturn_t mrfld_adc_thread_isr(int irq, void *data)
> +{
> +	struct iio_dev *indio_dev = data;
> +	struct mrfld_adc *adc = iio_priv(indio_dev);
> +
> +	complete(&adc->completion);
> +	return IRQ_HANDLED;
> +}
> +
> +static int mrfld_adc_single_conv(struct iio_dev *indio_dev,
> +				 struct iio_chan_spec const *chan,
> +				 int *result)
> +{
> +	struct mrfld_adc *adc = iio_priv(indio_dev);
> +	struct regmap *regmap = adc->regmap;
> +	unsigned int req;
> +	long timeout;
> +	u8 buf[2];
> +	int ret;
> +
> +	reinit_completion(&adc->completion);
> +
> +	regmap_update_bits(regmap, BCOVE_MADCIRQ, BCOVE_ADCIRQ_ALL, 0);
> +	regmap_update_bits(regmap, BCOVE_MIRQLVL1, BCOVE_LVL1_ADC, 0);
> +
> +	ret = regmap_read_poll_timeout(regmap, BCOVE_GPADCREQ, req,
> +				       !(req & BCOVE_GPADCREQ_BUSY),
> +				       2000, 1000000);
> +	if (ret)
> +		goto done;
> +
> +	req = mrfld_adc_requests[chan->channel];
> +	ret = regmap_write(regmap, BCOVE_GPADCREQ, BCOVE_GPADCREQ_IRQEN | req);
> +	if (ret)
> +		goto done;
> +
> +	timeout = wait_for_completion_interruptible_timeout(&adc->completion,
> +							    BCOVE_ADC_TIMEOUT);
> +	if (timeout < 0) {
> +		ret = timeout;
> +		goto done;
> +	}
> +	if (timeout == 0) {
> +		ret = -ETIMEDOUT;
> +		goto done;
> +	}
> +
> +	ret = regmap_bulk_read(regmap, chan->address, buf, 2);
> +	if (ret)
> +		goto done;
> +
> +	*result = get_unaligned_be16(buf);
> +	ret = IIO_VAL_INT;
> +
> +done:
> +	regmap_update_bits(regmap, BCOVE_MIRQLVL1, BCOVE_LVL1_ADC, 0xff);
> +	regmap_update_bits(regmap, BCOVE_MADCIRQ, BCOVE_ADCIRQ_ALL, 0xff);
> +
> +	return ret;
> +}
> +
> +static int mrfld_adc_read_raw(struct iio_dev *indio_dev,
> +			      struct iio_chan_spec const *chan,
> +			      int *val, int *val2, long mask)
> +{
> +	struct mrfld_adc *adc = iio_priv(indio_dev);
> +	int ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_RAW:
> +		mutex_lock(&adc->lock);
> +		ret = mrfld_adc_single_conv(indio_dev, chan, val);
> +		mutex_unlock(&adc->lock);
> +		return ret;
> +	default:
> +		return -EINVAL;
> +	}
> +}
> +
> +static const struct iio_info mrfld_adc_iio_info = {
> +	.read_raw = &mrfld_adc_read_raw,
> +};
> +
> +#define BCOVE_ADC_CHANNEL(_type, _channel, _datasheet_name, _address)	\
> +	{								\
> +		.indexed = 1,						\
> +		.type = _type,						\
> +		.channel = _channel,					\
> +		.address = _address,					\
> +		.datasheet_name = _datasheet_name,			\
> +		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
> +	}
> +
> +static const struct iio_chan_spec mrfld_adc_channels[] = {
> +	BCOVE_ADC_CHANNEL(IIO_VOLTAGE,    0, "CH0", 0xE9),
> +	BCOVE_ADC_CHANNEL(IIO_RESISTANCE, 1, "CH1", 0xEB),
> +	BCOVE_ADC_CHANNEL(IIO_CURRENT,    2, "CH2", 0xED),
> +	BCOVE_ADC_CHANNEL(IIO_TEMP,       3, "CH3", 0xCC),
> +	BCOVE_ADC_CHANNEL(IIO_TEMP,       4, "CH4", 0xC8),
> +	BCOVE_ADC_CHANNEL(IIO_TEMP,       5, "CH5", 0xCA),
> +	BCOVE_ADC_CHANNEL(IIO_TEMP,       6, "CH6", 0xC2),
> +	BCOVE_ADC_CHANNEL(IIO_TEMP,       7, "CH7", 0xC4),
> +	BCOVE_ADC_CHANNEL(IIO_TEMP,       8, "CH8", 0xC6),
> +};
> +
> +static struct iio_map iio_maps[] = {
> +	IIO_MAP("CH0", "bcove-battery", "VBATRSLT"),
> +	IIO_MAP("CH1", "bcove-battery", "BATTID"),
> +	IIO_MAP("CH2", "bcove-battery", "IBATRSLT"),
> +	IIO_MAP("CH3", "bcove-temp",    "PMICTEMP"),
> +	IIO_MAP("CH4", "bcove-temp",    "BATTEMP0"),
> +	IIO_MAP("CH5", "bcove-temp",    "BATTEMP1"),
> +	IIO_MAP("CH6", "bcove-temp",    "SYSTEMP0"),
> +	IIO_MAP("CH7", "bcove-temp",    "SYSTEMP1"),
> +	IIO_MAP("CH8", "bcove-temp",    "SYSTEMP2"),
> +	{}
> +};
> +
> +static int mrfld_adc_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct intel_soc_pmic *pmic = dev_get_drvdata(dev->parent);
> +	struct iio_dev *indio_dev;
> +	struct mrfld_adc *adc;
> +	int irq;
> +	int ret;
> +
> +	indio_dev = devm_iio_device_alloc(dev, sizeof(*indio_dev));
> +	if (!indio_dev)
> +		return -ENOMEM;
> +
> +	adc = iio_priv(indio_dev);
> +
> +	mutex_init(&adc->lock);
> +	init_completion(&adc->completion);
> +	adc->regmap = pmic->regmap;
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
> +
> +	ret = devm_request_threaded_irq(dev, irq, NULL, mrfld_adc_thread_isr,
> +					IRQF_ONESHOT | IRQF_SHARED, pdev->name,
> +					indio_dev);
> +	if (ret)
> +		return ret;
> +
> +	platform_set_drvdata(pdev, indio_dev);
> +
> +	indio_dev->dev.parent = dev;
> +	indio_dev->name = pdev->name;
> +
> +	indio_dev->channels = mrfld_adc_channels;
> +	indio_dev->num_channels = ARRAY_SIZE(mrfld_adc_channels);
> +	indio_dev->info = &mrfld_adc_iio_info;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +
> +	ret = iio_map_array_register(indio_dev, iio_maps);
> +	if (ret)
> +		return ret;
> +
> +	ret = devm_iio_device_register(dev, indio_dev);
Hmm.. I'm a stickler for precise reverse order between
probe and remove as it's easy to be sure things are
correct that way and using the devm interface here breaks that.

If it's all I find, I'll probably just fix it up by not
using the devm version of this and explicitly unregistering
in remove.


> +	if (ret < 0)
> +		goto err_array_unregister;
> +
> +	return 0;
> +
> +err_array_unregister:
> +	iio_map_array_unregister(indio_dev);
> +	return ret;
> +}
> +
> +static int mrfld_adc_remove(struct platform_device *pdev)
> +{
> +	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> +
> +	iio_map_array_unregister(indio_dev);
> +
> +	return 0;
> +}
> +
> +static const struct platform_device_id mrfld_adc_id_table[] = {
> +	{ .name = "mrfld_bcove_adc" },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(platform, mrfld_adc_id_table);
> +
> +static struct platform_driver mrfld_adc_driver = {
> +	.driver = {
> +		.name = "mrfld_bcove_adc",
> +	},
> +	.probe = mrfld_adc_probe,
> +	.remove = mrfld_adc_remove,
> +	.id_table = mrfld_adc_id_table,
> +};
> +module_platform_driver(mrfld_adc_driver);
> +
> +MODULE_AUTHOR("Bin Yang <bin.yang@intel.com>");
> +MODULE_AUTHOR("Vincent Pelletier <plr.vincent@gmail.com>");
> +MODULE_AUTHOR("Andy Shevchenko <andriy.shevchenko@linux.intel.com>");
> +MODULE_DESCRIPTION("ADC driver for Basin Cove PMIC");
> +MODULE_LICENSE("GPL v2");


^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
  2019-03-30 15:31 ` Jonathan Cameron
@ 2019-09-02 13:13   ` Andy Shevchenko
  2019-09-03 17:51     ` Jonathan Cameron
  0 siblings, 1 reply; 8+ messages in thread
From: Andy Shevchenko @ 2019-09-02 13:13 UTC (permalink / raw)
  To: Jonathan Cameron
  Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
	linux-iio, Vincent Pelletier, Tomasz Duszynski

On Sat, Mar 30, 2019 at 03:31:40PM +0000, Jonathan Cameron wrote:
> On Tue, 26 Mar 2019 16:51:38 +0200
> Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:
> 
> > From: Vincent Pelletier <plr.vincent@gmail.com>
> > 
> > Exposes the ADC device present on, at least, Intel Merrifield platform.
> > 
> > Based on work done by:
> >   Yang Bin <bin.yang@intel.com>
> >   Huiquan Zhong <huiquan.zhong@intel.com>
> >   Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
> >   Pavan Kumar S <pavan.kumar.s@intel.com>
> > 
> > Though it has been heavily rewritten for upstream.
> > 
> > Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
> > Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> 
> Hmm. There is a very small ordering issue in probe vs remove, which
> I'll probably just fix up.
> 
> However I don't yet have the header in my upstream so will wait
> until that is there before applying.  If Lee or whoever is dealing
> with that patch set puts out an immutable branch with it in then
> let me know.
> 
> Give me a poke if I seem to have forgotten it.

Hi, Jonathan.

Lee applied the main driver to his tree [1].
Should I do anything for this one or is it applicable clean?

[1]: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=b9a801dfa591

-- 
With Best Regards,
Andy Shevchenko



^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
  2019-09-02 13:13   ` Andy Shevchenko
@ 2019-09-03 17:51     ` Jonathan Cameron
  2019-10-01  8:19       ` Andy Shevchenko
  0 siblings, 1 reply; 8+ messages in thread
From: Jonathan Cameron @ 2019-09-03 17:51 UTC (permalink / raw)
  To: Andy Shevchenko
  Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
	linux-iio, Vincent Pelletier, Tomasz Duszynski, Lee Jones

On Mon, 2 Sep 2019 16:13:01 +0300
Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:

> On Sat, Mar 30, 2019 at 03:31:40PM +0000, Jonathan Cameron wrote:
> > On Tue, 26 Mar 2019 16:51:38 +0200
> > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:
> >   
> > > From: Vincent Pelletier <plr.vincent@gmail.com>
> > > 
> > > Exposes the ADC device present on, at least, Intel Merrifield platform.
> > > 
> > > Based on work done by:
> > >   Yang Bin <bin.yang@intel.com>
> > >   Huiquan Zhong <huiquan.zhong@intel.com>
> > >   Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
> > >   Pavan Kumar S <pavan.kumar.s@intel.com>
> > > 
> > > Though it has been heavily rewritten for upstream.
> > > 
> > > Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
> > > Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>  
> > 
> > Hmm. There is a very small ordering issue in probe vs remove, which
> > I'll probably just fix up.
> > 
> > However I don't yet have the header in my upstream so will wait
> > until that is there before applying.  If Lee or whoever is dealing
> > with that patch set puts out an immutable branch with it in then
> > let me know.
> > 
> > Give me a poke if I seem to have forgotten it.  
> 
> Hi, Jonathan.
> 
> Lee applied the main driver to his tree [1].
> Should I do anything for this one or is it applicable clean?
> 
> [1]: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=b9a801dfa591
> 
Hmm. It's very late in the cycle and Lee doesn't have that in an immutable
branch (presumably because it's very late or it wasn't clear there was
a need to do so).  In theory I've done my last pull request to Greg
(though I messed it up so that's not quite true).

Will have to pick this up towards the start of the next cycle now I think.

Sorry, sometimes timing is against us!

Jonathan



^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
  2019-09-03 17:51     ` Jonathan Cameron
@ 2019-10-01  8:19       ` Andy Shevchenko
  2019-10-15 15:14         ` Andy Shevchenko
  0 siblings, 1 reply; 8+ messages in thread
From: Andy Shevchenko @ 2019-10-01  8:19 UTC (permalink / raw)
  To: Jonathan Cameron
  Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
	linux-iio, Vincent Pelletier, Tomasz Duszynski, Lee Jones

On Tue, Sep 03, 2019 at 06:51:19PM +0100, Jonathan Cameron wrote:
> On Mon, 2 Sep 2019 16:13:01 +0300
> Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:
> > On Sat, Mar 30, 2019 at 03:31:40PM +0000, Jonathan Cameron wrote:
> > > On Tue, 26 Mar 2019 16:51:38 +0200
> > > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:

> > > Give me a poke if I seem to have forgotten it.  

> > Lee applied the main driver to his tree [1].
> > Should I do anything for this one or is it applicable clean?
> > 
> > [1]: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=b9a801dfa591
> > 
> Hmm. It's very late in the cycle and Lee doesn't have that in an immutable
> branch (presumably because it's very late or it wasn't clear there was
> a need to do so).  In theory I've done my last pull request to Greg
> (though I messed it up so that's not quite true).
> 
> Will have to pick this up towards the start of the next cycle now I think.

Now everything needed is in v5.4-rc1. Your move!

-- 
With Best Regards,
Andy Shevchenko



^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
  2019-10-01  8:19       ` Andy Shevchenko
@ 2019-10-15 15:14         ` Andy Shevchenko
  2019-10-15 15:40           ` jic23
  0 siblings, 1 reply; 8+ messages in thread
From: Andy Shevchenko @ 2019-10-15 15:14 UTC (permalink / raw)
  To: Jonathan Cameron
  Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
	linux-iio, Vincent Pelletier, Tomasz Duszynski, Lee Jones

On Tue, Oct 01, 2019 at 11:19:33AM +0300, Andy Shevchenko wrote:
> On Tue, Sep 03, 2019 at 06:51:19PM +0100, Jonathan Cameron wrote:
> > On Mon, 2 Sep 2019 16:13:01 +0300
> > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:
> > > On Sat, Mar 30, 2019 at 03:31:40PM +0000, Jonathan Cameron wrote:
> > > > On Tue, 26 Mar 2019 16:51:38 +0200
> > > > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:
> 
> > > > Give me a poke if I seem to have forgotten it.  
> 
> > > Lee applied the main driver to his tree [1].
> > > Should I do anything for this one or is it applicable clean?
> > > 
> > > [1]: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=b9a801dfa591
> > > 
> > Hmm. It's very late in the cycle and Lee doesn't have that in an immutable
> > branch (presumably because it's very late or it wasn't clear there was
> > a need to do so).  In theory I've done my last pull request to Greg
> > (though I messed it up so that's not quite true).
> > 
> > Will have to pick this up towards the start of the next cycle now I think.
> 
> Now everything needed is in v5.4-rc1. Your move!

Jonathan, anything I can do to make this accepted?

-- 
With Best Regards,
Andy Shevchenko



^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
  2019-10-15 15:14         ` Andy Shevchenko
@ 2019-10-15 15:40           ` jic23
  2019-10-15 20:05             ` Jonathan Cameron
  0 siblings, 1 reply; 8+ messages in thread
From: jic23 @ 2019-10-15 15:40 UTC (permalink / raw)
  To: Andy Shevchenko
  Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
	linux-iio, Vincent Pelletier, Tomasz Duszynski, Lee Jones

On 15.10.2019 16:14, Andy Shevchenko wrote:
> On Tue, Oct 01, 2019 at 11:19:33AM +0300, Andy Shevchenko wrote:
>> On Tue, Sep 03, 2019 at 06:51:19PM +0100, Jonathan Cameron wrote:
>> > On Mon, 2 Sep 2019 16:13:01 +0300
>> > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:
>> > > On Sat, Mar 30, 2019 at 03:31:40PM +0000, Jonathan Cameron wrote:
>> > > > On Tue, 26 Mar 2019 16:51:38 +0200
>> > > > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:
>> 
>> > > > Give me a poke if I seem to have forgotten it.
>> 
>> > > Lee applied the main driver to his tree [1].
>> > > Should I do anything for this one or is it applicable clean?
>> > >
>> > > [1]: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=b9a801dfa591
>> > >
>> > Hmm. It's very late in the cycle and Lee doesn't have that in an immutable
>> > branch (presumably because it's very late or it wasn't clear there was
>> > a need to do so).  In theory I've done my last pull request to Greg
>> > (though I messed it up so that's not quite true).
>> >
>> > Will have to pick this up towards the start of the next cycle now I think.
>> 
>> Now everything needed is in v5.4-rc1. Your move!
> 
> Jonathan, anything I can do to make this accepted?
Nearly  there.  Upstream from iio.git should now have the dependencies
and I'm in a state to rebase (as of yesterday).  If it's a quiet day
I'll get it done this evening!

Sorry for the delay - my fault for picking a random point at which to
base  my tree rather than waiting for rc1.

Jonathan

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver
  2019-10-15 15:40           ` jic23
@ 2019-10-15 20:05             ` Jonathan Cameron
  0 siblings, 0 replies; 8+ messages in thread
From: Jonathan Cameron @ 2019-10-15 20:05 UTC (permalink / raw)
  To: Andy Shevchenko
  Cc: Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
	linux-iio, Vincent Pelletier, Tomasz Duszynski, Lee Jones

On Tue, 15 Oct 2019 16:40:42 +0100
jic23@kernel.org wrote:

> On 15.10.2019 16:14, Andy Shevchenko wrote:
> > On Tue, Oct 01, 2019 at 11:19:33AM +0300, Andy Shevchenko wrote:  
> >> On Tue, Sep 03, 2019 at 06:51:19PM +0100, Jonathan Cameron wrote:  
> >> > On Mon, 2 Sep 2019 16:13:01 +0300
> >> > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:  
> >> > > On Sat, Mar 30, 2019 at 03:31:40PM +0000, Jonathan Cameron wrote:  
> >> > > > On Tue, 26 Mar 2019 16:51:38 +0200
> >> > > > Andy Shevchenko <andriy.shevchenko@linux.intel.com> wrote:  
> >>   
> >> > > > Give me a poke if I seem to have forgotten it.  
> >>   
> >> > > Lee applied the main driver to his tree [1].
> >> > > Should I do anything for this one or is it applicable clean?
> >> > >
> >> > > [1]: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=b9a801dfa591
> >> > >  
> >> > Hmm. It's very late in the cycle and Lee doesn't have that in an immutable
> >> > branch (presumably because it's very late or it wasn't clear there was
> >> > a need to do so).  In theory I've done my last pull request to Greg
> >> > (though I messed it up so that's not quite true).
> >> >
> >> > Will have to pick this up towards the start of the next cycle now I think.  
> >> 
> >> Now everything needed is in v5.4-rc1. Your move!  
> > 
> > Jonathan, anything I can do to make this accepted?  
> Nearly  there.  Upstream from iio.git should now have the dependencies
> and I'm in a state to rebase (as of yesterday).  If it's a quiet day
> I'll get it done this evening!
> 
> Sorry for the delay - my fault for picking a random point at which to
> base  my tree rather than waiting for rc1.
> 
> Jonathan

Yikes, getting the driver to actually build doesn't half require chasing
down a lot of dependencies.  Anyhow, now applied to the togreg branch of
iio.git and pushed out as testing for the autobuilders to poke at it.

Thanks,

Jonathan


^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, other threads:[~2019-10-15 20:05 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-03-26 14:51 [PATCH v2] iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver Andy Shevchenko
2019-03-30 15:31 ` Jonathan Cameron
2019-09-02 13:13   ` Andy Shevchenko
2019-09-03 17:51     ` Jonathan Cameron
2019-10-01  8:19       ` Andy Shevchenko
2019-10-15 15:14         ` Andy Shevchenko
2019-10-15 15:40           ` jic23
2019-10-15 20:05             ` Jonathan Cameron

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).