From: Alexandru Tachici <alexandru.tachici@analog.com> To: <linux-iio@vger.kernel.org>, <linux-kernel@vger.kernel.org> Cc: <jic23@kernel.org>, Alexandru Tachici <alexandru.tachici@analog.com> Subject: [PATCH v3 4/5] Documentation: ABI: testing: ad7192: update sysfs docs Date: Wed, 12 Feb 2020 18:17:20 +0200 Message-ID: <20200212161721.16200-5-alexandru.tachici@analog.com> (raw) In-Reply-To: <20200212161721.16200-1-alexandru.tachici@analog.com> Updated mainline documentation on ad7192 userspace sysfs. Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> --- .../ABI/testing/sysfs-bus-iio-adc-ad7192 | 24 ++++++++++++++----- .../iio/Documentation/sysfs-bus-iio-ad7192 | 20 ---------------- 2 files changed, 18 insertions(+), 26 deletions(-) delete mode 100644 drivers/staging/iio/Documentation/sysfs-bus-iio-ad7192 diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-ad7192 b/Documentation/ABI/testing/sysfs-bus-iio-adc-ad7192 index 7627d3be08f5..f8315202c8f0 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-adc-ad7192 +++ b/Documentation/ABI/testing/sysfs-bus-iio-adc-ad7192 @@ -2,17 +2,22 @@ What: /sys/bus/iio/devices/iio:deviceX/ac_excitation_en KernelVersion: Contact: linux-iio@vger.kernel.org Description: - Reading gives the state of AC excitation. - Writing '1' enables AC excitation. + This attribute, if available, is used to enable the AC + excitation mode found on some converters. In ac excitation mode, + the polarity of the excitation voltage is reversed on + alternate cycles, to eliminate DC errors. What: /sys/bus/iio/devices/iio:deviceX/bridge_switch_en KernelVersion: Contact: linux-iio@vger.kernel.org Description: - This bridge switch is used to disconnect it when there is a - need to minimize the system current consumption. - Reading gives the state of the bridge switch. - Writing '1' enables the bridge switch. + This attribute, if available, is used to close or open the + bridge power down switch found on some converters. + In bridge applications, such as strain gauges and load cells, + the bridge itself consumes the majority of the current in the + system. To minimize the current consumption of the system, + the bridge can be disconnected (when it is not being used + using the bridge_switch_en attribute. What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration KernelVersion: @@ -21,6 +26,13 @@ Description: Initiates the system calibration procedure. This is done on a single channel at a time. Write '1' to start the calibration. +What: /sys/bus/iio/devices/iio:deviceX/in_voltage2-voltage2_shorted_raw +KernelVersion: +Contact: linux-iio@vger.kernel.org +Description: + Measure voltage from AIN2 pin connected to AIN(+) + and AIN(-) shorted. + What: /sys/bus/iio/devices/iio:deviceX/in_voltagex_sys_calibration_mode_available KernelVersion: Contact: linux-iio@vger.kernel.org diff --git a/drivers/staging/iio/Documentation/sysfs-bus-iio-ad7192 b/drivers/staging/iio/Documentation/sysfs-bus-iio-ad7192 deleted file mode 100644 index 1c35c507cc05..000000000000 --- a/drivers/staging/iio/Documentation/sysfs-bus-iio-ad7192 +++ /dev/null @@ -1,20 +0,0 @@ -What: /sys/.../iio:deviceX/ac_excitation_en -KernelVersion: 3.1.0 -Contact: linux-iio@vger.kernel.org -Description: - This attribute, if available, is used to enable the AC - excitation mode found on some converters. In ac excitation mode, - the polarity of the excitation voltage is reversed on - alternate cycles, to eliminate DC errors. - -What: /sys/.../iio:deviceX/bridge_switch_en -KernelVersion: 3.1.0 -Contact: linux-iio@vger.kernel.org -Description: - This attribute, if available, is used to close or open the - bridge power down switch found on some converters. - In bridge applications, such as strain gauges and load cells, - the bridge itself consumes the majority of the current in the - system. To minimize the current consumption of the system, - the bridge can be disconnected (when it is not being used - using the bridge_switch_en attribute. -- 2.20.1
next prev parent reply index Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-02-12 16:17 [PATCH v3 0/5] iio: adc: ad7192: move out of staging Alexandru Tachici 2020-02-12 16:17 ` [PATCH v3 1/5] staging: iio: adc: ad7192: fail probe on get_voltage Alexandru Tachici 2020-02-14 15:40 ` Jonathan Cameron 2020-02-12 16:17 ` [PATCH v3 2/5] staging: iio: adc: ad7192: modify iio_chan_spec array Alexandru Tachici 2020-02-14 15:47 ` Jonathan Cameron 2020-02-12 16:17 ` [PATCH 3/5] staging: iio: adc: ad7192: removed spi_device_id Alexandru Tachici 2020-02-14 15:48 ` Jonathan Cameron 2020-02-12 16:17 ` Alexandru Tachici [this message] 2020-02-14 15:49 ` [PATCH v3 4/5] Documentation: ABI: testing: ad7192: update sysfs docs Jonathan Cameron 2020-02-12 16:17 ` [PATCH v3 5/5] staging: iio: adc: ad7192: move out of staging Alexandru Tachici 2020-02-14 15:50 ` Jonathan Cameron
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20200212161721.16200-5-alexandru.tachici@analog.com \ --to=alexandru.tachici@analog.com \ --cc=jic23@kernel.org \ --cc=linux-iio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
Linux-IIO Archive on lore.kernel.org Archives are clonable: git clone --mirror https://lore.kernel.org/linux-iio/0 linux-iio/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 linux-iio linux-iio/ https://lore.kernel.org/linux-iio \ linux-iio@vger.kernel.org public-inbox-index linux-iio Example config snippet for mirrors Newsgroup available over NNTP: nntp://nntp.lore.kernel.org/org.kernel.vger.linux-iio AGPL code for this site: git clone https://public-inbox.org/public-inbox.git