From: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
To: jic23@kernel.org, robh+dt@kernel.org, robh@kernel.org,
mchehab+huawei@kernel.org, davem@davemloft.net,
gregkh@linuxfoundation.org
Cc: linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Subject: [PATCH 02/12] iio: imu: inv_icm42600: add I2C driver for inv_icm42600 driver
Date: Thu, 7 May 2020 16:42:12 +0200 [thread overview]
Message-ID: <20200507144222.20989-3-jmaneyrol@invensense.com> (raw)
In-Reply-To: <20200507144222.20989-1-jmaneyrol@invensense.com>
Add I2C driver for InvenSense ICM-426xxx devices.
Configure bus signal slew rates as indicated in the datasheet.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
---
.../iio/imu/inv_icm42600/inv_icm42600_i2c.c | 117 ++++++++++++++++++
1 file changed, 117 insertions(+)
create mode 100644 drivers/iio/imu/inv_icm42600/inv_icm42600_i2c.c
diff --git a/drivers/iio/imu/inv_icm42600/inv_icm42600_i2c.c b/drivers/iio/imu/inv_icm42600/inv_icm42600_i2c.c
new file mode 100644
index 000000000000..b61f993beacf
--- /dev/null
+++ b/drivers/iio/imu/inv_icm42600/inv_icm42600_i2c.c
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2020 InvenSense, Inc.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/of_device.h>
+
+#include "inv_icm42600.h"
+
+static int inv_icm42600_i2c_bus_setup(struct inv_icm42600_state *st)
+{
+ unsigned int mask, val;
+ int ret;
+
+ /* setup interface registers */
+ mask = INV_ICM42600_INTF_CONFIG6_MASK;
+ val = INV_ICM42600_INTF_CONFIG6_I3C_EN;
+ ret = regmap_update_bits(st->map, INV_ICM42600_REG_INTF_CONFIG6,
+ mask, val);
+ if (ret)
+ return ret;
+
+ mask = INV_ICM42600_INTF_CONFIG4_I3C_BUS_ONLY;
+ val = 0;
+ ret = regmap_update_bits(st->map, INV_ICM42600_REG_INTF_CONFIG4,
+ mask, val);
+ if (ret)
+ return ret;
+
+ /* set slew rates for I2C and SPI */
+ mask = INV_ICM42600_DRIVE_CONFIG_I2C_MASK |
+ INV_ICM42600_DRIVE_CONFIG_SPI_MASK;
+ val = INV_ICM42600_DRIVE_CONFIG_I2C(INV_ICM42600_SLEW_RATE_12_36NS) |
+ INV_ICM42600_DRIVE_CONFIG_SPI(INV_ICM42600_SLEW_RATE_12_36NS);
+ ret = regmap_update_bits(st->map, INV_ICM42600_REG_DRIVE_CONFIG,
+ mask, val);
+ if (ret)
+ return ret;
+
+ /* disable SPI bus */
+ mask = INV_ICM42600_INTF_CONFIG0_UI_SIFS_CFG_MASK;
+ val = INV_ICM42600_INTF_CONFIG0_UI_SIFS_CFG_SPI_DIS;
+ return regmap_update_bits(st->map, INV_ICM42600_REG_INTF_CONFIG0,
+ mask, val);
+}
+
+static int inv_icm42600_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ const void *match;
+ enum inv_icm42600_chip chip;
+ struct regmap *regmap;
+
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_I2C_BLOCK))
+ return -ENOTSUPP;
+
+ match = device_get_match_data(&client->dev);
+ if (match)
+ chip = (enum inv_icm42600_chip)match;
+ else if (id)
+ chip = (enum inv_icm42600_chip)id->driver_data;
+ else
+ return -EINVAL;
+
+ regmap = devm_regmap_init_i2c(client, &inv_icm42600_regmap_config);
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ return inv_icm42600_core_probe(regmap, chip,
+ inv_icm42600_i2c_bus_setup);
+}
+
+static const struct of_device_id inv_icm42600_of_matches[] = {
+ {
+ .compatible = "invensense,icm42600",
+ .data = (void *)INV_CHIP_ICM42600,
+ }, {
+ .compatible = "invensense,icm42602",
+ .data = (void *)INV_CHIP_ICM42602,
+ }, {
+ .compatible = "invensense,icm42605",
+ .data = (void *)INV_CHIP_ICM42605,
+ }, {
+ .compatible = "invensense,icm42622",
+ .data = (void *)INV_CHIP_ICM42622,
+ },
+ {}
+};
+MODULE_DEVICE_TABLE(of, inv_icm42600_of_matches);
+
+static const struct i2c_device_id inv_icm42600_ids[] = {
+ {"icm42600", INV_CHIP_ICM42600},
+ {"icm42602", INV_CHIP_ICM42602},
+ {"icm42605", INV_CHIP_ICM42605},
+ {"icm42622", INV_CHIP_ICM42622},
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, inv_icm42600_ids);
+
+static struct i2c_driver inv_icm42600_driver = {
+ .probe = inv_icm42600_probe,
+ .id_table = inv_icm42600_ids,
+ .driver = {
+ .of_match_table = inv_icm42600_of_matches,
+ .name = "inv-icm42600-i2c",
+ .pm = &inv_icm42600_pm_ops,
+ },
+};
+module_i2c_driver(inv_icm42600_driver);
+
+MODULE_AUTHOR("InvenSense, Inc.");
+MODULE_DESCRIPTION("InvenSense ICM-426xx I2C driver");
+MODULE_LICENSE("GPL");
--
2.17.1
next prev parent reply other threads:[~2020-05-07 14:43 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-07 14:42 [PATCH 00/12] iio: imu: new inv_icm42600 driver Jean-Baptiste Maneyrol
2020-05-07 14:42 ` [PATCH 01/12] iio: imu: inv_icm42600: add core of " Jean-Baptiste Maneyrol
2020-05-08 13:28 ` Jonathan Cameron
2020-05-18 14:14 ` Jean-Baptiste Maneyrol
2020-05-21 17:47 ` Jonathan Cameron
2020-05-07 14:42 ` Jean-Baptiste Maneyrol [this message]
2020-05-08 13:44 ` [PATCH 02/12] iio: imu: inv_icm42600: add I2C driver for " Jonathan Cameron
2020-05-18 14:19 ` Jean-Baptiste Maneyrol
2020-05-21 17:50 ` Jonathan Cameron
2020-05-07 14:42 ` [PATCH 03/12] iio: imu: inv_icm42600: add SPI " Jean-Baptiste Maneyrol
2020-05-07 14:42 ` [PATCH 04/12] iio: imu: inv_icm42600: add gyroscope IIO device Jean-Baptiste Maneyrol
2020-05-08 14:01 ` Jonathan Cameron
[not found] ` <MN2PR12MB4422B32CB3C4BFD0AF5FFF3CC4B80@MN2PR12MB4422.namprd12.prod.outlook.com>
2020-05-18 15:33 ` Jean-Baptiste Maneyrol
2020-05-21 17:55 ` Jonathan Cameron
2020-05-07 14:42 ` [PATCH 05/12] iio: imu: inv_icm42600: add accelerometer " Jean-Baptiste Maneyrol
2020-05-07 14:42 ` [PATCH 06/12] iio: imu: inv_icm42600: add temperature sensor support Jean-Baptiste Maneyrol
2020-05-07 14:42 ` [PATCH 07/12] iio: imu: add Kconfig and Makefile for inv_icm42600 driver Jean-Baptiste Maneyrol
2020-05-07 14:42 ` [PATCH 08/12] iio: imu: inv_icm42600: add device interrupt trigger Jean-Baptiste Maneyrol
2020-05-08 14:22 ` Jonathan Cameron
2020-05-18 15:41 ` Jean-Baptiste Maneyrol
2020-05-07 14:42 ` [PATCH 09/12] iio: imu: inv_icm42600: add buffer support in iio devices Jean-Baptiste Maneyrol
2020-05-08 14:19 ` Jonathan Cameron
2020-05-18 15:32 ` Jean-Baptiste Maneyrol
2020-05-21 17:56 ` Jonathan Cameron
2020-05-07 14:42 ` [PATCH 10/12] iio: imu: inv_icm42600: add accurate timestamping Jean-Baptiste Maneyrol
2020-05-08 14:42 ` Jonathan Cameron
2020-05-18 15:48 ` Jean-Baptiste Maneyrol
2020-05-07 14:42 ` [PATCH 11/12] dt-bindings: iio: imu: Add inv_icm42600 documentation Jean-Baptiste Maneyrol
2020-05-15 3:00 ` Rob Herring
2020-05-07 14:42 ` [PATCH 12/12] MAINTAINERS: add entry for inv_icm42600 6-axis imu sensor Jean-Baptiste Maneyrol
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200507144222.20989-3-jmaneyrol@invensense.com \
--to=jmaneyrol@invensense.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jic23@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mchehab+huawei@kernel.org \
--cc=robh+dt@kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).