From: Yong Wu <yong.wu@mediatek.com>
To: chao hao <Chao.Hao@mediatek.com>
Cc: youlin.pei@mediatek.com, devicetree@vger.kernel.org,
Nicolas Boichat <drinkcat@chromium.org>,
cui.zhang@mediatek.com, srv_heupstream@mediatek.com,
Robin Murphy <robin.murphy@arm.com>,
linux-kernel@vger.kernel.org, Evan Green <evgreen@chromium.org>,
Tomasz Figa <tfiga@google.com>,
iommu@lists.linux-foundation.org,
Rob Herring <robh+dt@kernel.org>,
linux-mediatek@lists.infradead.org,
Matthias Brugger <matthias.bgg@gmail.com>,
chao hao <"Chao. Hao"@mediatek.com>,
ming-fan.chen@mediatek.com, anan.sun@mediatek.com,
Will Deacon <will@kernel.org>,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 11/21] iommu/mediatek: Add power-domain operation
Date: Fri, 7 Aug 2020 10:13:58 +0800 [thread overview]
Message-ID: <1596766438.18559.4.camel@mhfsdcap03> (raw)
In-Reply-To: <1595839778.2350.4.camel@mbjsdccf07>
On Mon, 2020-07-27 at 16:49 +0800, chao hao wrote:
> On Sat, 2020-07-11 at 14:48 +0800, Yong Wu wrote:
> > In the previous SoC, the M4U HW is in the EMI power domain which is
> > always on. the latest M4U is in the display power domain which may be
> > turned on/off, thus we have to add pm_runtime interface for it.
> >
> > we should enable its power before M4U hw initial. and disable it after HW
> > initialize.
> >
> > When the engine work, the engine always enable the power and clocks for
> > smi-larb/smi-common, then the M4U's power will always be powered on
> > automatically via the device link with smi-common.
> >
> > Note: we don't enable the M4U power in iommu_map/unmap for tlb flush.
> > If its power already is on, of course it is ok. if the power is off,
> > the main tlb will be reset while M4U power on, thus the tlb flush while
> > m4u power off is unnecessary, just skip it.
> >
> > Signed-off-by: Yong Wu <yong.wu@mediatek.com>
...
> >
> > if (data->plat_data->m4u_plat == M4U_MT8173) {
> > @@ -728,7 +756,15 @@ static int mtk_iommu_probe(struct platform_device *pdev)
> >
> > platform_set_drvdata(pdev, data);
> >
> > + if (dev->pm_domain)
> > + pm_runtime_enable(dev);
>
> hi yong,
>
> If you put "pm_runtime_enable" here, it maybe not device_link with
> smi_common for previous patch:
> if(i || !pm_runtime_enabled(dev))
> continue;
>
> Whether put it up front?
Thanks for review. My fault here. I will fix it.
>
> best regards,
> chao
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
next prev parent reply other threads:[~2020-08-07 2:14 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-11 6:48 [PATCH 00/21] MT8192 IOMMU support Yong Wu
2020-07-11 6:48 ` [PATCH 01/21] dt-binding: memory: mediatek: Add a common larb-port header file Yong Wu
2020-07-12 18:06 ` Matthias Brugger
2020-07-13 5:43 ` Pi-Hsun Shih
2020-07-13 6:28 ` Yong Wu
2020-07-13 6:27 ` [SPAM]Re: " Yong Wu
2020-07-20 22:58 ` Rob Herring
2020-07-11 6:48 ` [PATCH 02/21] dt-binding: memory: mediatek: Extend LARB_NR_MAX to 32 Yong Wu
2020-07-20 22:59 ` Rob Herring
2020-07-11 6:48 ` [PATCH 03/21] dt-binding: memory: mediatek: Add domain definition Yong Wu
2020-07-11 6:48 ` [PATCH 04/21] dt-binding: mediatek: Add binding for mt8192 IOMMU and SMI Yong Wu
2020-07-13 5:36 ` Pi-Hsun Shih
2020-07-13 6:54 ` Yong Wu
2020-07-20 23:16 ` Rob Herring
2020-07-21 3:27 ` Yong Wu
2020-07-11 6:48 ` [PATCH 05/21] iommu/mediatek: Use the common mtk-smi-larb-port.h Yong Wu
2020-07-11 6:48 ` [PATCH 06/21] iommu/io-pgtable-arm-v7s: Use ias to check the valid iova in unmap Yong Wu
2020-07-13 0:38 ` Nicolas Boichat
2020-07-13 6:52 ` Yong Wu
2020-07-11 6:48 ` [PATCH 07/21] iommu/io-pgtable-arm-v7s: Extend PA34 for MediaTek Yong Wu
2020-07-11 6:48 ` [PATCH 08/21] iommu/io-pgtable-arm-v7s: Add cfg as a param in some macros Yong Wu
2020-07-11 6:48 ` [PATCH 09/21] iommu/io-pgtable-arm-v7s: Quad lvl1 pgtable for MediaTek Yong Wu
2020-07-11 6:48 ` [PATCH 10/21] iommu/mediatek: Add device link for smi-common and m4u Yong Wu
2020-07-11 6:48 ` [PATCH 11/21] iommu/mediatek: Add power-domain operation Yong Wu
2020-07-13 7:03 ` Pi-Hsun Shih
2020-07-14 9:33 ` Yong Wu
2020-07-27 8:49 ` chao hao
2020-08-07 2:13 ` Yong Wu [this message]
2020-07-11 6:48 ` [PATCH 12/21] iommu/mediatek: Add iova reserved function Yong Wu
2020-07-13 7:33 ` Pi-Hsun Shih
2020-07-14 9:32 ` Yong Wu
2020-07-11 6:48 ` [PATCH 13/21] iommu/mediatek: Make MTK_IOMMU depend on ARM64 Yong Wu
2020-07-11 6:48 ` [PATCH 14/21] iommu/mediatek: Add single domain Yong Wu
2020-07-11 6:48 ` [PATCH 15/21] iommu/mediatek: Support master use iova over 32bit Yong Wu
2020-07-11 6:48 ` [PATCH 16/21] iommu/mediatek: Support up to 34bit iova in tlb invalid Yong Wu
2020-07-11 6:48 ` [PATCH 17/21] iommu/mediatek: Support report iova 34bit translation fault in ISR Yong Wu
2020-07-11 6:48 ` [PATCH 18/21] iommu/mediatek: Add support for multi domain Yong Wu
2020-07-23 20:47 ` Rob Herring
2020-07-27 6:41 ` Yong Wu
2020-07-11 6:48 ` [PATCH 19/21] iommu/mediatek: Adjust the structure Yong Wu
2020-07-11 6:48 ` [PATCH 20/21] iommu/mediatek: Add mt8192 support Yong Wu
2020-07-11 6:48 ` [PATCH 21/21] memory: mtk-smi: " Yong Wu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1596766438.18559.4.camel@mhfsdcap03 \
--to=yong.wu@mediatek.com \
--cc="Chao. Hao"@mediatek.com \
--cc=Chao.Hao@mediatek.com \
--cc=anan.sun@mediatek.com \
--cc=cui.zhang@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=drinkcat@chromium.org \
--cc=evgreen@chromium.org \
--cc=iommu@lists.linux-foundation.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=ming-fan.chen@mediatek.com \
--cc=robh+dt@kernel.org \
--cc=robin.murphy@arm.com \
--cc=srv_heupstream@mediatek.com \
--cc=tfiga@google.com \
--cc=will@kernel.org \
--cc=youlin.pei@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).