Linux-LEDs Archive on lore.kernel.org
 help / color / Atom feed
From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: matti.vaittinen@fi.rohmeurope.com, mazziesaccount@gmail.com
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>,
	Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Lee Jones <lee.jones@linaro.org>,
	Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	Bartosz Golaszewski <bgolaszewski@baylibre.com>,
	Alessandro Zummo <a.zummo@towertech.it>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-gpio@vger.kernel.org, linux-rtc@vger.kernel.org
Subject: [RFC PATCH v3 15/15] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
Date: Fri, 1 Nov 2019 13:51:25 +0200
Message-ID: <05813c82394481f5dc946b482902dc6cc2b91a44.1572606437.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1572606437.git.matti.vaittinen@fi.rohmeurope.com>

ROHM BD71828 PMIC contains 4 pins which can be configured by OTP
to be used for general purposes. First 3 can be used as outputs
and 4.th pin can be used as input. Allow them to be controlled
via GPIO framework.

The driver assumes all of the pins are configured as GPIOs and
trusts that the reserved pins in other OTP configurations are
excluded from control using "gpio-reserved-ranges" device tree
property (or left untouched by GPIO users).

Typical use for 4.th pin (input) is to use it as HALL sensor
input so that this pin state is toggled when HALL sensor detects
LID position change (from close to open or open to close). PMIC
HW implements some extra logic which allows PMIC to power-up the
system when this pin is toggled. Please see the data sheet for
details of GPIO options which can be selected by OTP settings.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---

Changes since v2 - fixed typo from commit msg, used generic GPIO_IN
and GPIO_OUT instead of defining driver local ones.

 drivers/gpio/Kconfig        |  12 +++
 drivers/gpio/Makefile       |   1 +
 drivers/gpio/gpio-bd71828.c | 149 ++++++++++++++++++++++++++++++++++++
 3 files changed, 162 insertions(+)
 create mode 100644 drivers/gpio/gpio-bd71828.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 38e096e6925f..b4089096f7f2 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -994,6 +994,18 @@ config GPIO_BD70528
 	  This driver can also be built as a module. If so, the module
 	  will be called gpio-bd70528.
 
+config GPIO_BD71828
+	tristate "ROHM BD71828 GPIO support"
+	depends on MFD_ROHM_BD71828
+	help
+	  Support for GPIOs on ROHM BD71828 PMIC. There are three GPIOs
+	  available on the ROHM PMIC in total. The GPIOs are limited to
+	  outputs only and pins must be configured to GPIO outputs by
+	  OTP. Enable this only if you want to use these pins as outputs.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called gpio-bd71828.
+
 config GPIO_BD9571MWV
 	tristate "ROHM BD9571 GPIO support"
 	depends on MFD_BD9571MWV
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index d2fd19c15bae..034b38996579 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -35,6 +35,7 @@ obj-$(CONFIG_GPIO_ASPEED)		+= gpio-aspeed.o
 obj-$(CONFIG_GPIO_ATH79)		+= gpio-ath79.o
 obj-$(CONFIG_GPIO_BCM_KONA)		+= gpio-bcm-kona.o
 obj-$(CONFIG_GPIO_BD70528)		+= gpio-bd70528.o
+obj-$(CONFIG_GPIO_BD71828)		+= gpio-bd71828.o
 obj-$(CONFIG_GPIO_BD9571MWV)		+= gpio-bd9571mwv.o
 obj-$(CONFIG_GPIO_BRCMSTB)		+= gpio-brcmstb.o
 obj-$(CONFIG_GPIO_BT8XX)		+= gpio-bt8xx.o
diff --git a/drivers/gpio/gpio-bd71828.c b/drivers/gpio/gpio-bd71828.c
new file mode 100644
index 000000000000..a8ab6085c2e8
--- /dev/null
+++ b/drivers/gpio/gpio-bd71828.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+
+#include <linux/gpio/driver.h>
+#include <linux/mfd/rohm-bd71828.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define GPIO_OUT_REG(off) (BD71828_REG_GPIO_CTRL1 + (off))
+#define HALL_GPIO_OFFSET 3
+
+struct bd71828_gpio {
+	struct rohm_regmap_dev chip;
+	struct gpio_chip gpio;
+};
+
+static void bd71828_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			     int value)
+{
+	int ret;
+	struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
+	u8 val = (value) ? BD71828_GPIO_OUT_HI : BD71828_GPIO_OUT_LO;
+
+	/*
+	 * The HALL input pin can only be used as input. If this is the pin
+	 * we are dealing with - then we are done
+	 */
+	if (offset == HALL_GPIO_OFFSET)
+		return;
+
+	ret = regmap_update_bits(bdgpio->chip.regmap, GPIO_OUT_REG(offset),
+				 BD71828_GPIO_OUT_MASK, val);
+	if (ret)
+		dev_err(bdgpio->chip.dev, "Could not set gpio to %d\n", value);
+}
+
+static int bd71828_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	int ret;
+	unsigned int val;
+	struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
+
+	if (offset == HALL_GPIO_OFFSET)
+		ret = regmap_read(bdgpio->chip.regmap, BD71828_REG_IO_STAT,
+				  &val);
+	else
+		ret = regmap_read(bdgpio->chip.regmap, GPIO_OUT_REG(offset),
+				  &val);
+	if (!ret)
+		ret = (val & BD71828_GPIO_OUT_MASK);
+
+	return ret;
+}
+
+static int bd71828_gpio_set_config(struct gpio_chip *chip, unsigned int offset,
+				   unsigned long config)
+{
+	struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
+
+	if (offset == HALL_GPIO_OFFSET)
+		return -ENOTSUPP;
+
+	switch (pinconf_to_config_param(config)) {
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		return regmap_update_bits(bdgpio->chip.regmap,
+					  GPIO_OUT_REG(offset),
+					  BD71828_GPIO_DRIVE_MASK,
+					  BD71828_GPIO_OPEN_DRAIN);
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		return regmap_update_bits(bdgpio->chip.regmap,
+					  GPIO_OUT_REG(offset),
+					  BD71828_GPIO_DRIVE_MASK,
+					  BD71828_GPIO_PUSH_PULL);
+	default:
+		break;
+	}
+	return -ENOTSUPP;
+}
+
+static int bd71828_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	/*
+	 * Pin usage is selected by OTP data. We can't read it runtime. Hence
+	 * we trust that if the pin is not excluded by "gpio-reserved-ranges"
+	 * the OTP configuration is set to OUT. (Other pins but HALL input pin
+	 * on BD71828 can't really be used for general purpose input - input
+	 * states are used for specific cases like regulator control or
+	 * PMIC_ON_REQ.
+	 */
+	if (offset == HALL_GPIO_OFFSET)
+		return GPIO_IN;
+
+	return GPIO_OUT;
+}
+
+static int bd71828_probe(struct platform_device *pdev)
+{
+	struct bd71828_gpio *bdgpio;
+	struct rohm_regmap_dev *bd71828;
+
+	bd71828 = dev_get_drvdata(pdev->dev.parent);
+	if (!bd71828) {
+		dev_err(&pdev->dev, "No MFD driver data\n");
+		return -EINVAL;
+	}
+
+	bdgpio = devm_kzalloc(&pdev->dev, sizeof(*bdgpio),
+			      GFP_KERNEL);
+	if (!bdgpio)
+		return -ENOMEM;
+
+	bdgpio->chip.dev = &pdev->dev;
+	bdgpio->gpio.parent = pdev->dev.parent;
+	bdgpio->gpio.label = "bd71828-gpio";
+	bdgpio->gpio.owner = THIS_MODULE;
+	bdgpio->gpio.get_direction = bd71828_get_direction;
+	bdgpio->gpio.set_config = bd71828_gpio_set_config;
+	bdgpio->gpio.can_sleep = true;
+	bdgpio->gpio.get = bd71828_gpio_get;
+	bdgpio->gpio.set = bd71828_gpio_set;
+	bdgpio->gpio.base = -1;
+
+	/*
+	 * See if we need some implementation to mark some PINs as
+	 * not controllable based on DT info or if core can handle
+	 * "gpio-reserved-ranges" and exclude them from control
+	 */
+	bdgpio->gpio.ngpio = 4;
+	bdgpio->gpio.of_node = pdev->dev.parent->of_node;
+	bdgpio->chip.regmap = bd71828->regmap;
+
+	return devm_gpiochip_add_data(&pdev->dev, &bdgpio->gpio,
+				     bdgpio);
+}
+
+static struct platform_driver bd71828_gpio = {
+	.driver = {
+		.name = "bd71828-gpio"
+	},
+	.probe = bd71828_probe,
+};
+
+module_platform_driver(bd71828_gpio);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71828 voltage regulator driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd71828-gpio");
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

  parent reply index

Thread overview: 38+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-01 11:28 [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Matti Vaittinen
2019-11-01 11:29 ` [RFC PATCH v3 01/15] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-11-11 10:57   ` Lee Jones
2019-11-11 11:20     ` Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 02/15] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
2019-11-05 20:43   ` Rob Herring
2019-11-06 12:55     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 03/15] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
2019-11-05 20:52   ` Rob Herring
2019-11-07  6:50     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:32 ` [RFC PATCH v3 04/15] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
2019-11-05 19:14   ` Dan Murphy
2019-11-05 20:59     ` Rob Herring
2019-11-06 13:05     ` Vaittinen, Matti
2019-11-05 20:57   ` Rob Herring
2019-11-01 11:33 ` [RFC PATCH v3 05/15] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-11-11 10:59   ` Lee Jones
2019-11-11 11:07     ` Vaittinen, Matti
2019-11-01 11:38 ` [RFC PATCH v3 06/15] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-11-01 11:39 ` [RFC PATCH v3 07/15] clk: bd718x7: simplify header dependencies Matti Vaittinen
2019-11-01 11:41 ` [RFC PATCH v3 08/15] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
2019-11-01 11:42 ` [RFC PATCH v3 09/15] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-11-01 11:43 ` [RFC PATCH v3 10/15] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
2019-11-03 22:27   ` Linus Walleij
2019-11-04  7:05     ` Vaittinen, Matti
2019-11-05 13:24       ` Linus Walleij
2019-11-05 14:07         ` Vaittinen, Matti
2019-11-01 11:44 ` [RFC PATCH v3 11/15] regulator: bd71828: enhanced run-level support Matti Vaittinen
2019-11-01 11:45 ` [RFC PATCH v3 12/15] regulator: bd71828: Support in-kernel APIs to change run-level Matti Vaittinen
2019-11-01 11:49 ` [RFC PATCH v3 13/15] rtc: bd70528 add BD71828 support Matti Vaittinen
2019-11-01 11:49 ` [RFC PATCH v3 14/15] gpio: Add definition for GPIO direction Matti Vaittinen
2019-11-03 22:30   ` Linus Walleij
2019-11-04  6:57     ` Vaittinen, Matti
2019-11-04 15:48     ` Vaittinen, Matti
2019-11-05 15:05       ` Linus Walleij
2019-11-06  6:51         ` Vaittinen, Matti
2019-11-01 11:51 ` Matti Vaittinen [this message]
2019-11-01 11:53 ` [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Vaittinen, Matti

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=05813c82394481f5dc946b482902dc6cc2b91a44.1572606437.git.matti.vaittinen@fi.rohmeurope.com \
    --to=matti.vaittinen@fi.rohmeurope.com \
    --cc=a.zummo@towertech.it \
    --cc=alexandre.belloni@bootlin.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=jacek.anaszewski@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mazziesaccount@gmail.com \
    --cc=mturquette@baylibre.com \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-LEDs Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-leds/0 linux-leds/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-leds linux-leds/ https://lore.kernel.org/linux-leds \
		linux-leds@vger.kernel.org
	public-inbox-index linux-leds

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-leds


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git