Linux-LEDs Archive on lore.kernel.org
 help / color / Atom feed
From: Dan Murphy <dmurphy@ti.com>
To: <jacek.anaszewski@gmail.com>, <pavel@ucw.cz>
Cc: <linux-leds@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	Dan Murphy <dmurphy@ti.com>
Subject: [PATCH v12 06/16] leds: lp50xx: Add the LP50XX family of the RGB LED driver
Date: Fri, 11 Oct 2019 08:06:47 -0500
Message-ID: <20191011130657.4713-7-dmurphy@ti.com> (raw)
In-Reply-To: <20191011130657.4713-1-dmurphy@ti.com>

Introduce the LP5036/30/24/18/12/9 RGB LED driver.
The difference in these parts are the number of
LED outputs where the:

LP5036 can control 36 LEDs
LP5030 can control 30 LEDs
LP5024 can control 24 LEDs
LP5018 can control 18 LEDs
LP5012 can control 12 LEDs
LP5009 can control 9 LEDs

The device has the ability to group LED output into control banks
so that multiple LED banks can be controlled with the same mixing and
brightness.  Inversely the LEDs can also be controlled independently.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 drivers/leds/Kconfig       |  11 +
 drivers/leds/Makefile      |   1 +
 drivers/leds/leds-lp50xx.c | 799 +++++++++++++++++++++++++++++++++++++
 3 files changed, 811 insertions(+)
 create mode 100644 drivers/leds/leds-lp50xx.c

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index a1ede89afc9e..fb614a6b9afa 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -363,6 +363,17 @@ config LEDS_LP3952
 	  To compile this driver as a module, choose M here: the
 	  module will be called leds-lp3952.
 
+config LEDS_LP50XX
+	tristate "LED Support for TI LP5036/30/24/18/12/9 LED driver chip"
+	depends on LEDS_CLASS && REGMAP_I2C
+	depends on LEDS_CLASS_MULTI_COLOR
+	help
+	  If you say yes here you get support for the Texas Instruments
+	  LP5036, LP5030, LP5024, LP5018, LP5012 and LP5009 LED driver.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called leds-lp50xx.
+
 config LEDS_LP55XX_COMMON
 	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
 	depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 841038cfe35b..7a208a0f7b84 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_LEDS_GPIO_REGISTER)	+= leds-gpio-register.o
 obj-$(CONFIG_LEDS_GPIO)			+= leds-gpio.o
 obj-$(CONFIG_LEDS_LP3944)		+= leds-lp3944.o
 obj-$(CONFIG_LEDS_LP3952)		+= leds-lp3952.o
+obj-$(CONFIG_LEDS_LP50XX)		+= leds-lp50xx.o
 obj-$(CONFIG_LEDS_LP55XX_COMMON)	+= leds-lp55xx-common.o
 obj-$(CONFIG_LEDS_LP5521)		+= leds-lp5521.o
 obj-$(CONFIG_LEDS_LP5523)		+= leds-lp5523.o
diff --git a/drivers/leds/leds-lp50xx.c b/drivers/leds/leds-lp50xx.c
new file mode 100644
index 000000000000..6a042f973a83
--- /dev/null
+++ b/drivers/leds/leds-lp50xx.c
@@ -0,0 +1,799 @@
+// SPDX-License-Identifier: GPL-2.0
+// TI LP50XX LED chip family driver
+// Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <uapi/linux/uleds.h>
+
+#include <linux/led-class-multicolor.h>
+
+#define LP50XX_DEV_CFG0		0x00
+#define LP50XX_DEV_CFG1		0x01
+#define LP50XX_LED_CFG0		0x02
+
+/* LP5009 and LP5012 registers */
+#define LP5012_BNK_BRT		0x03
+#define LP5012_BNKA_CLR		0x04
+#define LP5012_BNKB_CLR		0x05
+#define LP5012_BNKC_CLR		0x06
+#define LP5012_LED0_BRT		0x07
+#define LP5012_LED1_BRT		0x08
+#define LP5012_LED2_BRT		0x09
+#define LP5012_LED3_BRT		0x0a
+#define LP5012_OUT0_CLR		0x0b
+#define LP5012_OUT1_CLR		0x0c
+#define LP5012_OUT2_CLR		0x0d
+#define LP5012_OUT3_CLR		0x0e
+#define LP5012_OUT4_CLR		0x0f
+#define LP5012_OUT5_CLR		0x10
+#define LP5012_OUT6_CLR		0x11
+#define LP5012_OUT7_CLR		0x12
+#define LP5012_OUT8_CLR		0x13
+#define LP5012_OUT9_CLR		0x14
+#define LP5012_OUT10_CLR	0x15
+#define LP5012_OUT11_CLR	0x16
+#define LP5012_RESET		0x17
+
+/* LP5018 and LP5024 registers */
+#define LP5024_BNK_BRT		0x03
+#define LP5024_BNKA_CLR		0x04
+#define LP5024_BNKB_CLR		0x05
+#define LP5024_BNKC_CLR		0x06
+#define LP5024_LED0_BRT		0x07
+#define LP5024_LED1_BRT		0x08
+#define LP5024_LED2_BRT		0x09
+#define LP5024_LED3_BRT		0x0a
+#define LP5024_LED4_BRT		0x0b
+#define LP5024_LED5_BRT		0x0c
+#define LP5024_LED6_BRT		0x0d
+#define LP5024_LED7_BRT		0x0e
+
+#define LP5024_OUT0_CLR		0x0f
+#define LP5024_OUT1_CLR		0x10
+#define LP5024_OUT2_CLR		0x11
+#define LP5024_OUT3_CLR		0x12
+#define LP5024_OUT4_CLR		0x13
+#define LP5024_OUT5_CLR		0x14
+#define LP5024_OUT6_CLR		0x15
+#define LP5024_OUT7_CLR		0x16
+#define LP5024_OUT8_CLR		0x17
+#define LP5024_OUT9_CLR		0x18
+#define LP5024_OUT10_CLR	0x19
+#define LP5024_OUT11_CLR	0x1a
+#define LP5024_OUT12_CLR	0x1b
+#define LP5024_OUT13_CLR	0x1c
+#define LP5024_OUT14_CLR	0x1d
+#define LP5024_OUT15_CLR	0x1e
+#define LP5024_OUT16_CLR	0x1f
+#define LP5024_OUT17_CLR	0x20
+#define LP5024_OUT18_CLR	0x21
+#define LP5024_OUT19_CLR	0x22
+#define LP5024_OUT20_CLR	0x23
+#define LP5024_OUT21_CLR	0x24
+#define LP5024_OUT22_CLR	0x25
+#define LP5024_OUT23_CLR	0x26
+#define LP5024_RESET		0x27
+
+/* LP5030 and LP5036 registers */
+#define LP5036_LED_CFG1		0x03
+#define LP5036_BNK_BRT		0x04
+#define LP5036_BNKA_CLR		0x05
+#define LP5036_BNKB_CLR		0x06
+#define LP5036_BNKC_CLR		0x07
+#define LP5036_LED0_BRT		0x08
+#define LP5036_LED1_BRT		0x09
+#define LP5036_LED2_BRT		0x0a
+#define LP5036_LED3_BRT		0x0b
+#define LP5036_LED4_BRT		0x0c
+#define LP5036_LED5_BRT		0x0d
+#define LP5036_LED6_BRT		0x0e
+#define LP5036_LED7_BRT		0x0f
+#define LP5036_LED8_BRT		0x10
+#define LP5036_LED9_BRT		0x11
+#define LP5036_LED10_BRT	0x12
+#define LP5036_LED11_BRT	0x13
+
+#define LP5036_OUT0_CLR		0x14
+#define LP5036_OUT1_CLR		0x15
+#define LP5036_OUT2_CLR		0x16
+#define LP5036_OUT3_CLR		0x17
+#define LP5036_OUT4_CLR		0x18
+#define LP5036_OUT5_CLR		0x19
+#define LP5036_OUT6_CLR		0x1a
+#define LP5036_OUT7_CLR		0x1b
+#define LP5036_OUT8_CLR		0x1c
+#define LP5036_OUT9_CLR		0x1d
+#define LP5036_OUT10_CLR	0x1e
+#define LP5036_OUT11_CLR	0x1f
+#define LP5036_OUT12_CLR	0x20
+#define LP5036_OUT13_CLR	0x21
+#define LP5036_OUT14_CLR	0x22
+#define LP5036_OUT15_CLR	0x23
+#define LP5036_OUT16_CLR	0x24
+#define LP5036_OUT17_CLR	0x25
+#define LP5036_OUT18_CLR	0x26
+#define LP5036_OUT19_CLR	0x27
+#define LP5036_OUT20_CLR	0x28
+#define LP5036_OUT21_CLR	0x29
+#define LP5036_OUT22_CLR	0x2a
+#define LP5036_OUT23_CLR	0x2b
+#define LP5036_OUT24_CLR	0x2c
+#define LP5036_OUT25_CLR	0x2d
+#define LP5036_OUT26_CLR	0x2e
+#define LP5036_OUT27_CLR	0x2f
+#define LP5036_OUT28_CLR	0x30
+#define LP5036_OUT29_CLR	0x31
+#define LP5036_OUT30_CLR	0x32
+#define LP5036_OUT31_CLR	0x33
+#define LP5036_OUT32_CLR	0x34
+#define LP5036_OUT33_CLR	0x35
+#define LP5036_OUT34_CLR	0x36
+#define LP5036_OUT35_CLR	0x37
+#define LP5036_RESET		0x38
+
+#define LP50XX_SW_RESET		0xff
+#define LP50XX_CHIP_EN		BIT(6)
+
+/* There are 3 LED outputs per bank */
+#define LP50XX_LEDS_PER_MODULE	3
+
+#define LP5009_MAX_LED_MODULES	2
+#define LP5012_MAX_LED_MODULES	4
+#define LP5018_MAX_LED_MODULES	6
+#define LP5024_MAX_LED_MODULES	8
+#define LP5030_MAX_LED_MODULES	10
+#define LP5036_MAX_LED_MODULES	12
+
+#define LP5009_MAX_LEDS	(LP5009_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE)
+#define LP5012_MAX_LEDS	(LP5012_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE)
+#define LP5018_MAX_LEDS	(LP5018_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE)
+#define LP5024_MAX_LEDS	(LP5024_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE)
+#define LP5030_MAX_LEDS	(LP5030_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE)
+#define LP5036_MAX_LEDS	(LP5036_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE)
+
+static const struct reg_default lp5012_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5012_BNK_BRT, 0xff},
+	{LP5012_BNKA_CLR, 0x0f},
+	{LP5012_BNKB_CLR, 0x0f},
+	{LP5012_BNKC_CLR, 0x0f},
+	{LP5012_LED0_BRT, 0x0f},
+	{LP5012_LED1_BRT, 0xff},
+	{LP5012_LED2_BRT, 0xff},
+	{LP5012_LED3_BRT, 0xff},
+	{LP5012_OUT0_CLR, 0x0f},
+	{LP5012_OUT1_CLR, 0x00},
+	{LP5012_OUT2_CLR, 0x00},
+	{LP5012_OUT3_CLR, 0x00},
+	{LP5012_OUT4_CLR, 0x00},
+	{LP5012_OUT5_CLR, 0x00},
+	{LP5012_OUT6_CLR, 0x00},
+	{LP5012_OUT7_CLR, 0x00},
+	{LP5012_OUT8_CLR, 0x00},
+	{LP5012_OUT9_CLR, 0x00},
+	{LP5012_OUT10_CLR, 0x00},
+	{LP5012_OUT11_CLR, 0x00},
+	{LP5012_RESET, 0x00}
+};
+
+static const struct reg_default lp5024_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5024_BNK_BRT, 0xff},
+	{LP5024_BNKA_CLR, 0x0f},
+	{LP5024_BNKB_CLR, 0x0f},
+	{LP5024_BNKC_CLR, 0x0f},
+	{LP5024_LED0_BRT, 0x0f},
+	{LP5024_LED1_BRT, 0xff},
+	{LP5024_LED2_BRT, 0xff},
+	{LP5024_LED3_BRT, 0xff},
+	{LP5024_LED4_BRT, 0xff},
+	{LP5024_LED5_BRT, 0xff},
+	{LP5024_LED6_BRT, 0xff},
+	{LP5024_LED7_BRT, 0xff},
+	{LP5024_OUT0_CLR, 0x0f},
+	{LP5024_OUT1_CLR, 0x00},
+	{LP5024_OUT2_CLR, 0x00},
+	{LP5024_OUT3_CLR, 0x00},
+	{LP5024_OUT4_CLR, 0x00},
+	{LP5024_OUT5_CLR, 0x00},
+	{LP5024_OUT6_CLR, 0x00},
+	{LP5024_OUT7_CLR, 0x00},
+	{LP5024_OUT8_CLR, 0x00},
+	{LP5024_OUT9_CLR, 0x00},
+	{LP5024_OUT10_CLR, 0x00},
+	{LP5024_OUT11_CLR, 0x00},
+	{LP5024_OUT12_CLR, 0x00},
+	{LP5024_OUT13_CLR, 0x00},
+	{LP5024_OUT14_CLR, 0x00},
+	{LP5024_OUT15_CLR, 0x00},
+	{LP5024_OUT16_CLR, 0x00},
+	{LP5024_OUT17_CLR, 0x00},
+	{LP5024_OUT18_CLR, 0x00},
+	{LP5024_OUT19_CLR, 0x00},
+	{LP5024_OUT20_CLR, 0x00},
+	{LP5024_OUT21_CLR, 0x00},
+	{LP5024_OUT22_CLR, 0x00},
+	{LP5024_OUT23_CLR, 0x00},
+	{LP5024_RESET, 0x00}
+};
+
+static const struct reg_default lp5036_reg_defs[] = {
+	{LP50XX_DEV_CFG0, 0x0},
+	{LP50XX_DEV_CFG1, 0x3c},
+	{LP50XX_LED_CFG0, 0x0},
+	{LP5036_LED_CFG1, 0x0},
+	{LP5036_BNK_BRT, 0xff},
+	{LP5036_BNKA_CLR, 0x0f},
+	{LP5036_BNKB_CLR, 0x0f},
+	{LP5036_BNKC_CLR, 0x0f},
+	{LP5036_LED0_BRT, 0x0f},
+	{LP5036_LED1_BRT, 0xff},
+	{LP5036_LED2_BRT, 0xff},
+	{LP5036_LED3_BRT, 0xff},
+	{LP5036_LED4_BRT, 0xff},
+	{LP5036_LED5_BRT, 0xff},
+	{LP5036_LED6_BRT, 0xff},
+	{LP5036_LED7_BRT, 0xff},
+	{LP5036_OUT0_CLR, 0x0f},
+	{LP5036_OUT1_CLR, 0x00},
+	{LP5036_OUT2_CLR, 0x00},
+	{LP5036_OUT3_CLR, 0x00},
+	{LP5036_OUT4_CLR, 0x00},
+	{LP5036_OUT5_CLR, 0x00},
+	{LP5036_OUT6_CLR, 0x00},
+	{LP5036_OUT7_CLR, 0x00},
+	{LP5036_OUT8_CLR, 0x00},
+	{LP5036_OUT9_CLR, 0x00},
+	{LP5036_OUT10_CLR, 0x00},
+	{LP5036_OUT11_CLR, 0x00},
+	{LP5036_OUT12_CLR, 0x00},
+	{LP5036_OUT13_CLR, 0x00},
+	{LP5036_OUT14_CLR, 0x00},
+	{LP5036_OUT15_CLR, 0x00},
+	{LP5036_OUT16_CLR, 0x00},
+	{LP5036_OUT17_CLR, 0x00},
+	{LP5036_OUT18_CLR, 0x00},
+	{LP5036_OUT19_CLR, 0x00},
+	{LP5036_OUT20_CLR, 0x00},
+	{LP5036_OUT21_CLR, 0x00},
+	{LP5036_OUT22_CLR, 0x00},
+	{LP5036_OUT23_CLR, 0x00},
+	{LP5036_OUT24_CLR, 0x00},
+	{LP5036_OUT25_CLR, 0x00},
+	{LP5036_OUT26_CLR, 0x00},
+	{LP5036_OUT27_CLR, 0x00},
+	{LP5036_OUT28_CLR, 0x00},
+	{LP5036_OUT29_CLR, 0x00},
+	{LP5036_OUT30_CLR, 0x00},
+	{LP5036_OUT31_CLR, 0x00},
+	{LP5036_OUT32_CLR, 0x00},
+	{LP5036_OUT33_CLR, 0x00},
+	{LP5036_OUT34_CLR, 0x00},
+	{LP5036_OUT35_CLR, 0x00},
+	{LP5036_RESET, 0x00}
+};
+
+static const struct regmap_config lp5012_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5012_RESET,
+	.reg_defaults = lp5012_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5012_reg_defs),
+	.cache_type = REGCACHE_RBTREE,
+};
+
+static const struct regmap_config lp5024_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5024_RESET,
+	.reg_defaults = lp5024_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5024_reg_defs),
+	.cache_type = REGCACHE_RBTREE,
+};
+
+static const struct regmap_config lp5036_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = LP5036_RESET,
+	.reg_defaults = lp5036_reg_defs,
+	.num_reg_defaults = ARRAY_SIZE(lp5036_reg_defs),
+	.cache_type = REGCACHE_RBTREE,
+};
+
+enum lp50xx_model {
+	LP5009,
+	LP5012,
+	LP5018,
+	LP5024,
+	LP5030,
+	LP5036,
+};
+
+/*
+ * struct lp50xx_chip_info -
+ * @num_leds: number of LED outputs available on the device
+ * @led_brightness0_reg: first brightness register of the device
+ * @mix_out0_reg: first color mix register of the device
+ * @bank_brt_reg: bank brightness register
+ * @bank_mix_reg: color mix register
+ * @reset_reg: device reset register
+ */
+struct lp50xx_chip_info {
+	const struct regmap_config lp50xx_regmap_config;
+	int model_id;
+	u8 max_modules;
+	u8 num_leds;
+	u8 led_brightness0_reg;
+	u8 mix_out0_reg;
+	u8 bank_brt_reg;
+	u8 bank_mix_reg;
+	u8 reset_reg;
+};
+
+static const struct lp50xx_chip_info lp50xx_chip_info_tbl[] = {
+	[LP5009] = {
+		.model_id = LP5009,
+		.max_modules = LP5009_MAX_LED_MODULES,
+		.num_leds = LP5009_MAX_LEDS,
+		.led_brightness0_reg = LP5012_LED0_BRT,
+		.mix_out0_reg = LP5012_OUT0_CLR,
+		.bank_brt_reg = LP5012_BNK_BRT,
+		.bank_mix_reg = LP5012_BNKA_CLR,
+		.reset_reg = LP5012_RESET,
+		.lp50xx_regmap_config = lp5012_regmap_config,
+	},
+	[LP5012] = {
+		.model_id = LP5012,
+		.max_modules = LP5012_MAX_LED_MODULES,
+		.num_leds = LP5012_MAX_LEDS,
+		.led_brightness0_reg = LP5012_LED0_BRT,
+		.mix_out0_reg = LP5012_OUT0_CLR,
+		.bank_brt_reg = LP5012_BNK_BRT,
+		.bank_mix_reg = LP5012_BNKA_CLR,
+		.reset_reg = LP5012_RESET,
+		.lp50xx_regmap_config = lp5012_regmap_config,
+	},
+	[LP5018] = {
+		.model_id = LP5018,
+		.max_modules = LP5018_MAX_LED_MODULES,
+		.num_leds = LP5018_MAX_LEDS,
+		.led_brightness0_reg = LP5024_LED0_BRT,
+		.mix_out0_reg = LP5024_OUT0_CLR,
+		.bank_brt_reg = LP5024_BNK_BRT,
+		.bank_mix_reg = LP5024_BNKA_CLR,
+		.reset_reg = LP5024_RESET,
+		.lp50xx_regmap_config = lp5024_regmap_config,
+	},
+	[LP5024] = {
+		.model_id = LP5024,
+		.max_modules = LP5024_MAX_LED_MODULES,
+		.num_leds = LP5024_MAX_LEDS,
+		.led_brightness0_reg = LP5024_LED0_BRT,
+		.mix_out0_reg = LP5024_OUT0_CLR,
+		.bank_brt_reg = LP5024_BNK_BRT,
+		.bank_mix_reg = LP5024_BNKA_CLR,
+		.reset_reg = LP5024_RESET,
+		.lp50xx_regmap_config = lp5024_regmap_config,
+	},
+	[LP5030] = {
+		.model_id = LP5030,
+		.max_modules = LP5030_MAX_LED_MODULES,
+		.num_leds = LP5030_MAX_LEDS,
+		.led_brightness0_reg = LP5036_LED0_BRT,
+		.mix_out0_reg = LP5036_OUT0_CLR,
+		.bank_brt_reg = LP5036_BNK_BRT,
+		.bank_mix_reg = LP5036_BNKA_CLR,
+		.reset_reg = LP5036_RESET,
+		.lp50xx_regmap_config = lp5036_regmap_config,
+	},
+	[LP5036] = {
+		.model_id = LP5036,
+		.max_modules = LP5036_MAX_LED_MODULES,
+		.num_leds = LP5036_MAX_LEDS,
+		.led_brightness0_reg = LP5036_LED0_BRT,
+		.mix_out0_reg = LP5036_OUT0_CLR,
+		.bank_brt_reg = LP5036_BNK_BRT,
+		.bank_mix_reg = LP5036_BNKA_CLR,
+		.reset_reg = LP5036_RESET,
+		.lp50xx_regmap_config = lp5036_regmap_config,
+	},
+};
+
+struct lp50xx_led {
+	struct led_classdev led_dev;
+	struct led_classdev_mc mc_cdev;
+	struct lp50xx *priv;
+	unsigned long bank_modules;
+	int led_intensity[LP50XX_LEDS_PER_MODULE];
+	u8 ctrl_bank_enabled;
+	int led_number;
+};
+
+/**
+ * struct lp50xx -
+ * @enable_gpio: hardware enable gpio
+ * @regulator: LED supply regulator pointer
+ * @client: pointer to the I2C client
+ * @regmap: device register map
+ * @dev: pointer to the devices device struct
+ * @lock: lock for reading/writing the device
+ * @chip_info: chip specific information (ie num_leds)
+ * @num_of_banked_leds: holds the number of banked LEDs
+ * @leds: array of LED strings
+ */
+struct lp50xx {
+	struct gpio_desc *enable_gpio;
+	struct regulator *regulator;
+	struct i2c_client *client;
+	struct regmap *regmap;
+	struct device *dev;
+	struct mutex lock;
+	const struct lp50xx_chip_info *chip_info;
+	int num_of_banked_leds;
+
+	/* This needs to be at the end of the struct */
+	struct lp50xx_led leds[];
+};
+
+static int lp50xx_brightness_set(struct led_classdev *cdev,
+			     enum led_brightness brightness)
+{
+	struct lp50xx_led *led = container_of(cdev, struct lp50xx_led, led_dev);
+	const struct lp50xx_chip_info *led_chip = led->priv->chip_info;
+	struct led_mc_color_entry *color_data;
+	u8 led_offset, reg_val, reg_color_offset;
+	int ret = 0;
+
+	mutex_lock(&led->priv->lock);
+
+	if (led->ctrl_bank_enabled)
+		reg_val = led_chip->bank_brt_reg;
+	else
+		reg_val = led_chip->led_brightness0_reg +
+			  led->led_number;
+
+	ret = regmap_write(led->priv->regmap, reg_val, brightness);
+	if (ret) {
+		dev_err(&led->priv->client->dev,
+			"Cannot write brightness value %d\n", ret);
+		goto out;
+	}
+
+	list_for_each_entry(color_data, &led->mc_cdev.color_list, list) {
+		if (color_data->led_color_id == LED_COLOR_ID_RED) {
+			reg_color_offset = 0;
+		} else if (color_data->led_color_id == LED_COLOR_ID_GREEN) {
+			reg_color_offset = 1;
+		} else if (color_data->led_color_id == LED_COLOR_ID_BLUE) {
+			reg_color_offset = 2;
+		} else {
+			dev_err(&led->priv->client->dev,
+				"LED color not found\n");
+			ret = -EINVAL;
+			goto out;
+		}
+
+		if (led->ctrl_bank_enabled) {
+			reg_val = led_chip->bank_mix_reg + reg_color_offset;
+		} else {
+			led_offset = (led->led_number * 3)  + reg_color_offset;
+			reg_val = led_chip->mix_out0_reg + led_offset;
+		}
+
+		ret = regmap_write(led->priv->regmap, reg_val,
+				   color_data->intensity);
+		if (ret) {
+			dev_err(&led->priv->client->dev,
+				"Cannot write intensity value %d\n", ret);
+			goto out;
+		}
+	}
+out:
+	mutex_unlock(&led->priv->lock);
+	return ret;
+}
+
+static enum led_brightness lp50xx_brightness_get(struct led_classdev *cdev)
+{
+	struct lp50xx_led *led = container_of(cdev, struct lp50xx_led, led_dev);
+	const struct lp50xx_chip_info *led_chip = led->priv->chip_info;
+	unsigned int brt_val;
+	u8 reg_val;
+	int ret;
+
+	mutex_lock(&led->priv->lock);
+
+	if (led->ctrl_bank_enabled)
+		reg_val = led_chip->bank_brt_reg;
+	else
+		reg_val = led_chip->led_brightness0_reg + led->led_number;
+
+	ret = regmap_read(led->priv->regmap, reg_val, &brt_val);
+
+	mutex_unlock(&led->priv->lock);
+
+	return brt_val;
+}
+
+static int lp50xx_set_banks(struct lp50xx *priv, u32 led_banks[])
+{
+	u8 led_config_lo, led_config_hi;
+	u32 bank_enable_mask = 0;
+	int ret;
+	int i;
+
+	for (i = 0; i < priv->chip_info->num_leds; i++)
+		bank_enable_mask |= (1 << led_banks[i]);
+
+	led_config_lo = (u8)(bank_enable_mask & 0xff);
+	led_config_hi = (u8)(bank_enable_mask >> 8) & 0xff;
+
+	ret = regmap_write(priv->regmap, LP50XX_LED_CFG0, led_config_lo);
+	if (ret)
+		return ret;
+
+	if (priv->chip_info->model_id >= LP5030)
+		ret = regmap_write(priv->regmap, LP5036_LED_CFG1,
+				   led_config_hi);
+
+	return ret;
+}
+
+static int lp50xx_reset(struct lp50xx *priv)
+{
+	if (priv->enable_gpio)
+		return gpiod_direction_output(priv->enable_gpio, 1);
+	else
+		return regmap_write(priv->regmap, priv->chip_info->reset_reg,
+				    LP50XX_SW_RESET);
+}
+
+static int lp50xx_enable_disable(struct lp50xx *priv, u8 enable_disable)
+{
+	return regmap_write(priv->regmap, LP50XX_DEV_CFG0, enable_disable);
+}
+
+static int lp50xx_probe_dt(struct lp50xx *priv)
+{
+	u32 led_banks[LP5036_MAX_LED_MODULES];
+	struct fwnode_handle *child = NULL;
+	struct fwnode_handle *led_node = NULL;
+	struct led_init_data init_data;
+	struct lp50xx_led *led;
+	int num_colors;
+	u32 color_id;
+	int led_number;
+	size_t i = 0;
+	int ret;
+
+	priv->enable_gpio = devm_gpiod_get_optional(&priv->client->dev,
+						   "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(priv->enable_gpio)) {
+		ret = PTR_ERR(priv->enable_gpio);
+		dev_err(&priv->client->dev, "Failed to get enable gpio: %d\n",
+			ret);
+		return ret;
+	}
+
+	priv->regulator = devm_regulator_get(&priv->client->dev, "vled");
+	if (IS_ERR(priv->regulator))
+		priv->regulator = NULL;
+
+	device_for_each_child_node(&priv->client->dev, child) {
+		led = &priv->leds[i];
+		if (fwnode_property_present(child, "ti,led-bank")) {
+			ret = fwnode_property_read_u32_array(child,
+							     "ti,led-bank",
+							     NULL, 0);
+			priv->num_of_banked_leds = ret;
+			if (priv->num_of_banked_leds >
+			    priv->chip_info->max_modules) {
+				dev_err(&priv->client->dev,
+					"led-bank property is invalid\n");
+				ret = -EINVAL;
+				fwnode_handle_put(child);
+				goto child_out;
+			}
+
+			ret = fwnode_property_read_u32_array(child,
+							     "ti,led-bank",
+							     led_banks,
+							     ret);
+			if (ret) {
+				dev_err(&priv->client->dev,
+					"led-bank property is missing\n");
+				fwnode_handle_put(child);
+				goto child_out;
+			}
+
+			ret = lp50xx_set_banks(priv, led_banks);
+			if (ret) {
+				dev_err(&priv->client->dev,
+					"Cannot setup banked LEDs\n");
+				fwnode_handle_put(child);
+				goto child_out;
+			}
+			led->ctrl_bank_enabled = 1;
+
+		} else {
+			ret = fwnode_property_read_u32(child, "reg",
+					       &led_number);
+			if (ret) {
+				dev_err(&priv->client->dev,
+					"led reg property missing\n");
+				fwnode_handle_put(child);
+				goto child_out;
+			}
+
+			if (led_number > priv->chip_info->num_leds) {
+				dev_err(&priv->client->dev,
+					"led-sources property is invalid\n");
+				ret = -EINVAL;
+				fwnode_handle_put(child);
+				goto child_out;
+			}
+
+			led->led_number = led_number;
+		}
+
+		init_data.fwnode = child;
+		fwnode_property_read_string(child, "linux,default-trigger",
+				    &led->led_dev.default_trigger);
+		num_colors = 0;
+
+		fwnode_for_each_child_node(child, led_node) {
+			ret = fwnode_property_read_u32(led_node, "color",
+						       &color_id);
+			if (ret)
+				dev_err(&priv->client->dev,
+				"Cannot read color\n");
+
+			set_bit(color_id, &led->mc_cdev.available_colors);
+			num_colors++;
+
+		}
+
+		led->priv = priv;
+		led->mc_cdev.num_leds = num_colors;
+		led->mc_cdev.led_cdev = &led->led_dev;
+		led->led_dev.brightness_set_blocking = lp50xx_brightness_set;
+		led->led_dev.brightness_get = lp50xx_brightness_get;
+		ret = led_classdev_multicolor_register_ext(&priv->client->dev,
+						       &led->mc_cdev,
+						       &init_data);
+		if (ret) {
+			dev_err(&priv->client->dev, "led register err: %d\n",
+				ret);
+			fwnode_handle_put(child);
+			goto child_out;
+		}
+		i++;
+	}
+
+child_out:
+	return ret;
+}
+
+static int lp50xx_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct lp50xx *led;
+	int count;
+	int ret;
+
+	count = device_get_child_node_count(&client->dev);
+	if (!count) {
+		dev_err(&client->dev, "LEDs are not defined in device tree!");
+		return -ENODEV;
+	}
+
+	led = devm_kzalloc(&client->dev, struct_size(led, leds, count),
+			   GFP_KERNEL);
+	if (!led)
+		return -ENOMEM;
+
+	mutex_init(&led->lock);
+	led->client = client;
+	led->dev = &client->dev;
+	led->chip_info = &lp50xx_chip_info_tbl[id->driver_data];
+	i2c_set_clientdata(client, led);
+
+	led->regmap = devm_regmap_init_i2c(client,
+					&led->chip_info->lp50xx_regmap_config);
+	if (IS_ERR(led->regmap)) {
+		ret = PTR_ERR(led->regmap);
+		dev_err(&client->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	ret = lp50xx_reset(led);
+	if (ret)
+		return ret;
+
+	ret = lp50xx_probe_dt(led);
+	if (ret)
+		return ret;
+
+	return lp50xx_enable_disable(led, LP50XX_CHIP_EN);
+}
+
+static int lp50xx_remove(struct i2c_client *client)
+{
+	struct lp50xx *led = i2c_get_clientdata(client);
+	int ret;
+
+	ret = lp50xx_enable_disable(led, LP50XX_CHIP_EN);
+	if (ret) {
+		dev_err(&led->client->dev, "Failed to disable regulator\n");
+		return ret;
+	}
+
+	if (led->enable_gpio)
+		gpiod_direction_output(led->enable_gpio, 0);
+
+	if (led->regulator) {
+		ret = regulator_disable(led->regulator);
+		if (ret)
+			dev_err(&led->client->dev,
+				"Failed to disable regulator\n");
+	}
+
+	mutex_destroy(&led->lock);
+
+	return 0;
+}
+
+static const struct i2c_device_id lp50xx_id[] = {
+	{ "lp5009", LP5009 },
+	{ "lp5012", LP5012 },
+	{ "lp5018", LP5018 },
+	{ "lp5024", LP5024 },
+	{ "lp5030", LP5030 },
+	{ "lp5036", LP5036 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, lp50xx_id);
+
+static const struct of_device_id of_lp50xx_leds_match[] = {
+	{ .compatible = "ti,lp5009", .data = (void *)LP5009 },
+	{ .compatible = "ti,lp5012", .data = (void *)LP5012 },
+	{ .compatible = "ti,lp5018", .data = (void *)LP5018 },
+	{ .compatible = "ti,lp5024", .data = (void *)LP5024 },
+	{ .compatible = "ti,lp5030", .data = (void *)LP5030 },
+	{ .compatible = "ti,lp5036", .data = (void *)LP5036 },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_lp50xx_leds_match);
+
+static struct i2c_driver lp50xx_driver = {
+	.driver = {
+		.name	= "lp50xx",
+		.of_match_table = of_lp50xx_leds_match,
+	},
+	.probe		= lp50xx_probe,
+	.remove		= lp50xx_remove,
+	.id_table	= lp50xx_id,
+};
+module_i2c_driver(lp50xx_driver);
+
+MODULE_DESCRIPTION("Texas Instruments LP50XX LED driver");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.22.0.214.g8dca754b1e


  parent reply index

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-11 13:06 [PATCH v12 00/16] Multicolor Framework v12 Dan Murphy
2019-10-11 13:06 ` [PATCH v12 01/16] dt: bindings: Add multicolor class dt bindings documention Dan Murphy
2019-10-11 13:06 ` [PATCH v12 02/16] dt-bindings: leds: Add multicolor ID to the color ID list Dan Murphy
2019-10-11 13:06 ` [PATCH v12 03/16] " Dan Murphy
2019-10-11 13:06 ` [PATCH v12 04/16] leds: multicolor: Introduce a multicolor class definition Dan Murphy
2019-10-11 19:53   ` Jacek Anaszewski
2019-10-14  6:18   ` kbuild test robot
2019-10-11 13:06 ` [PATCH v12 05/16] dt: bindings: lp50xx: Introduce the lp50xx family of RGB drivers Dan Murphy
2019-10-11 13:06 ` Dan Murphy [this message]
2019-10-11 20:04   ` [PATCH v12 06/16] leds: lp50xx: Add the LP50XX family of the RGB LED driver Jacek Anaszewski
2019-10-14  9:17   ` kbuild test robot
2019-10-19 17:13     ` Jacek Anaszewski
2019-10-11 13:06 ` [PATCH v12 07/16] dt: bindings: lp55xx: Be consistent in the document with LED acronym Dan Murphy
2019-10-11 13:06 ` [PATCH v12 08/16] dt: bindings: lp55xx: Update binding for Multicolor Framework Dan Murphy
2019-10-11 20:15   ` Jacek Anaszewski
2019-10-12  0:54     ` Dan Murphy
2019-10-12 13:32       ` Jacek Anaszewski
2019-10-11 13:06 ` [PATCH v12 09/16] ARM: dts: n900: Add reg property to the LP5523 channel node Dan Murphy
2019-10-11 13:06 ` [PATCH v12 10/16] ARM: dts: imx6dl-yapp4: Add reg property to the lp5562 " Dan Murphy
2019-10-11 13:06 ` [PATCH v12 11/16] ARM: dts: ste-href: Add reg property to the LP5521 channel nodes Dan Murphy
2019-10-11 13:06 ` [PATCH v12 12/16] leds: lp55xx: Add multicolor framework support to lp55xx Dan Murphy
2019-10-11 20:36   ` Jacek Anaszewski
2019-10-12  0:50     ` Dan Murphy
2019-10-12 13:27       ` Jacek Anaszewski
2019-10-11 13:06 ` [PATCH v12 13/16] leds: lp5523: Update the lp5523 code to add intensity function Dan Murphy
2019-10-11 13:06 ` [PATCH v12 14/16] leds: lp5521: Add multicolor framework intensity support Dan Murphy
2019-10-11 13:06 ` [PATCH v12 15/16] leds: lp55xx: Fix checkpatch file permissions issues Dan Murphy
2019-10-11 13:06 ` [PATCH v12 16/16] leds: lp5523: Fix checkpatch issues in the code Dan Murphy
2019-10-11 19:40 ` [PATCH v12 00/16] Multicolor Framework v12 Jacek Anaszewski
2019-10-12  0:48   ` Dan Murphy

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191011130657.4713-7-dmurphy@ti.com \
    --to=dmurphy@ti.com \
    --cc=jacek.anaszewski@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=pavel@ucw.cz \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-LEDs Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-leds/0 linux-leds/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-leds linux-leds/ https://lore.kernel.org/linux-leds \
		linux-leds@vger.kernel.org linux-leds@archiver.kernel.org
	public-inbox-index linux-leds

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-leds


AGPL code for this site: git clone https://public-inbox.org/ public-inbox