[PATCH V6 0/4] Add support for WLED5

[PATCH V6 0/4] Add support for WLED5

[Kiran Gunda]

Currently, WLED driver supports only WLED4 peripherals that is present
on pmi8998 and pm660L. This patch series  converts the existing WLED4
bindings from .txt to .yaml format and adds the support for WLED5 peripheral
that is present on PM8150L.

PM8150L WLED supports the following.
    - Two modulators and each sink can use any of the modulator
    - Multiple CABC selection options
    - Multiple brightness width selection (12 bits to 15 bits)

Changes from V1:
	- Rebased on top of the below commit.
	  backlight: qcom-wled: Fix unsigned comparison to zero

Changes from V2:
	- Addressed Bjorn's comments by splitting the WLED4 changes
	  in a seperate patch.
	- Added WLED5 auto calibration support

Changes from V3:
        - Addressed comments from Daniel Thompson and Rob Herring
        - Seperated the WLED5 bindings from the driver changes
         - Squashed wled5 auto string detection and wled5 basic changes
          to avoid the NULL callback function pointer issue.

Changes from V4:
        - Addressed the yaml formatting comments from Rob Herring.
        - Addressed the comments from Daniel Thompson on the below patch
  	  "backlight: qcom-wled: Add callback functions"

Changes from V5:
        - This series depends on the below patch.
          https://lore.kernel.org/patchwork/patch/1226258/
        - Addressed yaml formatting comments from Rob Herring.
        - Removed the "wled_ovp_fault_status" callback as per Daniel Thomson
          suggestion from patch #2.
        - Addressed comments from Daniel Thomson on patch #4.

Kiran Gunda (3):
  backlight: qcom-wled: convert the wled bindings to .yaml format
  backlight: qcom-wled: Add callback functions
  backlight: qcom-wled: Add WLED5 bindings

Subbaraman Narayanamurthy (1):
  backlight: qcom-wled: Add support for WLED5 peripheral that is present
    on PM8150L PMICs

 .../bindings/leds/backlight/qcom-wled.txt          | 154 ------
 .../bindings/leds/backlight/qcom-wled.yaml         | 261 +++++++++
 drivers/video/backlight/qcom-wled.c                | 589 ++++++++++++++++++---
 3 files changed, 777 insertions(+), 227 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project

[PATCH V6 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format

[Kiran Gunda]

Convert the qcom-wled bindings from .txt to .yaml format.
Also replace PM8941 to WLED3 and PMI8998 to WLED4.

Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
---
 .../bindings/leds/backlight/qcom-wled.txt          | 154 ---------------
 .../bindings/leds/backlight/qcom-wled.yaml         | 208 +++++++++++++++++++++
 2 files changed, 208 insertions(+), 154 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml

diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
deleted file mode 100644
index c06863b..0000000
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
+++ /dev/null
@@ -1,154 +0,0 @@
-Binding for Qualcomm Technologies, Inc. WLED driver
-
-WLED (White Light Emitting Diode) driver is used for controlling display
-backlight that is part of PMIC on Qualcomm Technologies, Inc. reference
-platforms. The PMIC is connected to the host processor via SPMI bus.
-
-- compatible
-	Usage:        required
-	Value type:   <string>
-	Definition:   should be one of:
-			"qcom,pm8941-wled"
-			"qcom,pmi8998-wled"
-			"qcom,pm660l-wled"
-
-- reg
-	Usage:        required
-	Value type:   <prop encoded array>
-	Definition:   Base address of the WLED modules.
-
-- default-brightness
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   brightness value on boot, value from: 0-4095.
-		      Default: 2048
-
-- label
-	Usage:        required
-	Value type:   <string>
-	Definition:   The name of the backlight device
-
-- qcom,cs-out
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   enable current sink output.
-		      This property is supported only for PM8941.
-
-- qcom,cabc
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   enable content adaptive backlight control.
-
-- qcom,ext-gen
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   use externally generated modulator signal to dim.
-		      This property is supported only for PM8941.
-
-- qcom,current-limit
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   mA; per-string current limit; value from 0 to 25 with
-		      1 mA step. Default 20 mA.
-		      This property is supported only for pm8941.
-
-- qcom,current-limit-microamp
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   uA; per-string current limit; value from 0 to 30000 with
-		      2500 uA step. Default 25 mA.
-
-- qcom,current-boost-limit
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   mA; boost current limit.
-		      For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400,
-		      1680. Default: 805 mA.
-		      For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300,
-		      1500. Default: 970 mA.
-
-- qcom,switching-freq
-	Usage:        optional
-	Value type:   <u32>
-	 Definition:   kHz; switching frequency; one of: 600, 640, 685, 738,
-		       800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200,
-		       4800, 9600.
-		       Default: for pm8941: 1600 kHz
-				for pmi8998: 800 kHz
-
-- qcom,ovp
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   V; Over-voltage protection limit; one of:
-		      27, 29, 32, 35. Default: 29V
-		      This property is supported only for PM8941.
-
-- qcom,ovp-millivolt
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   mV; Over-voltage protection limit;
-		      For pmi8998: one of 18100, 19600, 29600, 31100.
-		      Default 29600 mV.
-		      If this property is not specified for PM8941, it
-		      falls back to "qcom,ovp" property.
-
-- qcom,num-strings
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   #; number of led strings attached;
-		      value: For PM8941 from 1 to 3. Default: 2
-			     For PMI8998 from 1 to 4.
-
-- interrupts
-	Usage:        optional
-	Value type:   <prop encoded array>
-	Definition:   Interrupts associated with WLED. This should be
-		      "short" and "ovp" interrupts. Interrupts can be
-		      specified as per the encoding listed under
-		      Documentation/devicetree/bindings/spmi/
-		      qcom,spmi-pmic-arb.txt.
-
-- interrupt-names
-	Usage:        optional
-	Value type:   <string>
-	Definition:   Interrupt names associated with the interrupts.
-		      Must be "short" and "ovp". The short circuit detection
-		      is not supported for PM8941.
-
-- qcom,enabled-strings
-	Usage:        optional
-	Value tyoe:   <u32 array>
-	Definition:   Array of the WLED strings numbered from 0 to 3. Each
-		      string of leds are operated individually. Specify the
-		      list of strings used by the device. Any combination of
-		      led strings can be used.
-
-- qcom,external-pfet
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   Specify if external PFET control for short circuit
-		      protection is used. This property is supported only
-		      for PMI8998.
-
-- qcom,auto-string-detection
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   Enables auto-detection of the WLED string configuration.
-		      This feature is not supported for PM8941.
-
-
-Example:
-
-pm8941-wled@d800 {
-	compatible = "qcom,pm8941-wled";
-	reg = <0xd800>;
-	label = "backlight";
-
-	qcom,cs-out;
-	qcom,current-limit = <20>;
-	qcom,current-boost-limit = <805>;
-	qcom,switching-freq = <1600>;
-	qcom,ovp = <29>;
-	qcom,num-strings = <2>;
-	qcom,enabled-strings = <0 1>;
-};
diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
new file mode 100644
index 0000000..b835443b
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
@@ -0,0 +1,208 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Binding for Qualcomm Technologies, Inc. WLED driver
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+  - Kiran Gunda <kgunda@codeaurora.org>
+
+description: |
+  WLED (White Light Emitting Diode) driver is used for controlling display
+  backlight that is part of PMIC on Qualcomm Technologies, Inc. reference
+  platforms. The PMIC is connected to the host processor via SPMI bus.
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm8941-wled
+      - qcom,pmi8998-wled
+      - qcom,pm660l-wled
+
+  reg:
+    maxItems: 1
+
+  default-brightness:
+    description: |
+      brightness value on boot.
+    minimum: 0
+    maximum: 4095
+    default: 2048
+
+  label: true
+
+  qcom,cs-out:
+    description: |
+      enable current sink output.
+      This property is supported only for WLED3.
+    type: boolean
+
+  qcom,cabc:
+    description: |
+      enable content adaptive backlight control.
+    type: boolean
+
+  qcom,ext-gen:
+    description: |
+      use externally generated modulator signal to dim.
+      This property is supported only for WLED3.
+    type: boolean
+
+  qcom,current-limit:
+    description: |
+      mA; per-string current limit.
+      This property is supported only for WLED3.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    default: 20
+    minimum: 0
+    maximum: 25
+
+  qcom,current-limit-microamp:
+    description: |
+      uA; per-string current limit.
+    default: 25
+    minimum: 0
+    maximum: 30000
+    multipleOf: 25
+
+  qcom,current-boost-limit:
+    description: |
+      mA; boost current limit.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+
+  qcom,switching-freq:
+    description: |
+      kHz; switching frequency.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, 4800, 9600 ]
+
+  qcom,ovp:
+    description: |
+      V; Over-voltage protection limit.
+      This property is supported only for WLED3.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 27, 29, 32, 35 ]
+      - default: 29
+
+  qcom,ovp-millivolt:
+    description: |
+      Over-voltage protection limit. This property is for WLED4 only.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 18100, 19600, 29600, 31100 ]
+      - default: 29600
+
+  qcom,num-strings:
+    description: |
+      number of led strings attached.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+
+  qcom,enabled-strings:
+    description: |
+      Array of the WLED strings numbered from 0 to 3. Each
+      string of leds are operated individually. Specify the
+      list of strings used by the device. Any combination of
+      led strings can be used.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    maxItems: 4
+
+  qcom,external-pfet:
+    description: |
+      Specify if external PFET control for short circuit
+      protection is used. This property is supported only
+      for WLED4.
+    type: boolean
+
+  qcom,auto-string-detection:
+    description: |
+      Enables auto-detection of the WLED string configuration.
+      This feature is not supported for WLED3.
+    type: boolean
+
+  interrupts:
+    minItems: 1
+    items:
+      - description: over voltage protection interrupt.
+      - description: short circuit interrupt.
+
+  interrupt-names:
+    minItems: 1
+    items:
+      - const: ovp
+      - const: short
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: qcom,pm8941-wled
+
+    then:
+      properties:
+        qcom,current-boost-limit:
+          enum: [ 105, 385, 525, 805, 980, 1260, 1400, 1680 ]
+          default: 805
+
+        qcom,switching-freq:
+          default: 1600
+
+        qcom,num-strings:
+          enum: [ 1, 2, 3 ]
+
+        interrupts:
+          maxItems: 1
+
+        interrupt-names:
+          maxItems: 1
+
+    else:
+      properties:
+        qcom,current-boost-limit:
+          enum: [ 105, 280, 450, 620, 970, 1150, 1300, 1500 ]
+          default: 970
+
+        qcom,switching-freq:
+          default: 800
+
+        qcom,num-strings:
+          enum: [ 1, 2, 3, 4 ]
+
+        interrupts:
+          minItems: 2
+
+        interrupt-names:
+          minItems: 2
+
+required:
+  - compatible
+  - reg
+  - label
+
+additionalProperties: false
+
+examples:
+  - |
+    backlight@d800 {
+        compatible = "qcom,pm8941-wled";
+        reg = <0xd800 0x100>;
+        label = "backlight";
+
+        qcom,cs-out;
+        qcom,current-limit = <20>;
+        qcom,current-boost-limit = <805>;
+        qcom,switching-freq = <1600>;
+        qcom,ovp = <29>;
+        qcom,num-strings = <2>;
+        qcom,enabled-strings = <0 1>;
+     };
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project

[PATCH V6 2/4] backlight: qcom-wled: Add callback functions

[Kiran Gunda]

Add wled_cabc_config, wled_sync_toggle, wled_ovp_fault_status
and wled_ovp_delay and wled_auto_detection_required callback
functions to prepare the driver for adding WLED5 support.

Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
---
 drivers/video/backlight/qcom-wled.c | 213 ++++++++++++++++++++++++------------
 1 file changed, 141 insertions(+), 72 deletions(-)

diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c
index df53fbd..7b0095e 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c
@@ -147,6 +147,7 @@ struct wled {
 	u32 max_brightness;
 	u32 short_count;
 	u32 auto_detect_count;
+	u32 version;
 	bool disabled_by_short;
 	bool has_short_detect;
 	int short_irq;
@@ -154,7 +155,30 @@ struct wled {
 
 	struct wled_config cfg;
 	struct delayed_work ovp_work;
+
+	/* Configures the brightness. Applicable for wled3, wled4 and wled5 */
 	int (*wled_set_brightness)(struct wled *wled, u16 brightness);
+
+	/* Configures the cabc register. Applicable for wled4 and wled5 */
+	int (*wled_cabc_config)(struct wled *wled, bool enable);
+
+	/*
+	 * Toggles the sync bit for the brightness update to take place.
+	 * Applicable for WLED3, WLED4 and WLED5.
+	 */
+	int (*wled_sync_toggle)(struct wled *wled);
+
+	/*
+	 * Time to wait before checking the OVP status after wled module enable.
+	 * Applicable for WLED4 and WLED5.
+	 */
+	int (*wled_ovp_delay)(struct wled *wled);
+
+	/*
+	 * Determines if the auto string detection is required.
+	 * Applicable for WLED4 and WLED5
+	 */
+	bool (*wled_auto_detection_required)(struct wled *wled);
 };
 
 static int wled3_set_brightness(struct wled *wled, u16 brightness)
@@ -237,7 +261,7 @@ static int wled_module_enable(struct wled *wled, int val)
 	return 0;
 }
 
-static int wled_sync_toggle(struct wled *wled)
+static int wled3_sync_toggle(struct wled *wled)
 {
 	int rc;
 	unsigned int mask = GENMASK(wled->max_string_count - 1, 0);
@@ -255,6 +279,46 @@ static int wled_sync_toggle(struct wled *wled)
 	return rc;
 }
 
+static int wled_ovp_fault_status(struct wled *wled, bool *fault_set)
+{
+	int rc;
+	u32 int_rt_sts, fault_sts;
+
+	*fault_set = false;
+	rc = regmap_read(wled->regmap,
+			wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS,
+			&int_rt_sts);
+	if (rc < 0) {
+		dev_err(wled->dev, "Failed to read INT_RT_STS rc=%d\n", rc);
+		return rc;
+	}
+
+	rc = regmap_read(wled->regmap,
+			wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS,
+			&fault_sts);
+	if (rc < 0) {
+		dev_err(wled->dev, "Failed to read FAULT_STATUS rc=%d\n", rc);
+		return rc;
+	}
+
+	if (int_rt_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS)
+		*fault_set = true;
+
+	if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT)
+		*fault_set = true;
+
+	if (*fault_set)
+		dev_dbg(wled->dev, "WLED OVP fault detected, int_rt_sts=0x%x fault_sts=0x%x\n",
+			int_rt_sts, fault_sts);
+
+	return rc;
+}
+
+static int wled4_ovp_delay(struct wled *wled)
+{
+	return WLED_SOFT_START_DLY_US;
+}
+
 static int wled_update_status(struct backlight_device *bl)
 {
 	struct wled *wled = bl_get_data(bl);
@@ -275,7 +339,7 @@ static int wled_update_status(struct backlight_device *bl)
 			goto unlock_mutex;
 		}
 
-		rc = wled_sync_toggle(wled);
+		rc = wled->wled_sync_toggle(wled);
 		if (rc < 0) {
 			dev_err(wled->dev, "wled sync failed rc:%d\n", rc);
 			goto unlock_mutex;
@@ -298,6 +362,25 @@ static int wled_update_status(struct backlight_device *bl)
 	return rc;
 }
 
+static int wled4_cabc_config(struct wled *wled, bool enable)
+{
+	int i, j, rc;
+	u8 val;
+
+	for (i = 0; i < wled->cfg.num_strings; i++) {
+		j = wled->cfg.enabled_strings[i];
+
+		val = enable ? WLED4_SINK_REG_STR_CABC_MASK : 0;
+		rc = regmap_update_bits(wled->regmap, wled->sink_addr +
+					WLED4_SINK_REG_STR_CABC(j),
+					WLED4_SINK_REG_STR_CABC_MASK, val);
+		if (rc < 0)
+			return rc;
+	}
+
+	return 0;
+}
+
 #define WLED_SHORT_DLY_MS			20
 #define WLED_SHORT_CNT_MAX			5
 #define WLED_SHORT_RESET_CNT_DLY_US		USEC_PER_SEC
@@ -345,9 +428,10 @@ static irqreturn_t wled_short_irq_handler(int irq, void *_wled)
 
 static void wled_auto_string_detection(struct wled *wled)
 {
-	int rc = 0, i;
-	u32 sink_config = 0, int_sts;
+	int rc = 0, i, delay_time_us;
+	u32 sink_config = 0;
 	u8 sink_test = 0, sink_valid = 0, val;
+	bool fault_set;
 
 	/* Read configured sink configuration */
 	rc = regmap_read(wled->regmap, wled->sink_addr +
@@ -376,14 +460,9 @@ static void wled_auto_string_detection(struct wled *wled)
 	}
 
 	if (wled->cfg.cabc) {
-		for (i = 0; i < wled->cfg.num_strings; i++) {
-			rc = regmap_update_bits(wled->regmap, wled->sink_addr +
-						WLED4_SINK_REG_STR_CABC(i),
-						WLED4_SINK_REG_STR_CABC_MASK,
-						0);
-			if (rc < 0)
-				goto failed_detect;
-		}
+		rc = wled->wled_cabc_config(wled, false);
+		if (rc < 0)
+			goto failed_detect;
 	}
 
 	/* Disable all sinks */
@@ -427,18 +506,17 @@ static void wled_auto_string_detection(struct wled *wled)
 			goto failed_detect;
 		}
 
-		usleep_range(WLED_SOFT_START_DLY_US,
-			     WLED_SOFT_START_DLY_US + 1000);
+		delay_time_us = wled->wled_ovp_delay(wled);
+		usleep_range(delay_time_us, delay_time_us + 1000);
 
-		rc = regmap_read(wled->regmap, wled->ctrl_addr +
-				 WLED3_CTRL_REG_INT_RT_STS, &int_sts);
+		rc = wled_ovp_fault_status(wled, &fault_set);
 		if (rc < 0) {
-			dev_err(wled->dev, "Error in reading WLED3_CTRL_INT_RT_STS rc=%d\n",
+			dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n",
 				rc);
 			goto failed_detect;
 		}
 
-		if (int_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS)
+		if (fault_set)
 			dev_dbg(wled->dev, "WLED OVP fault detected with SINK %d\n",
 				i + 1);
 		else
@@ -478,30 +556,30 @@ static void wled_auto_string_detection(struct wled *wled)
 	}
 
 	/* Enable valid sinks */
-	for (i = 0; i < wled->cfg.num_strings; i++) {
-		if (wled->cfg.cabc) {
-			rc = regmap_update_bits(wled->regmap, wled->sink_addr +
-						WLED4_SINK_REG_STR_CABC(i),
-						WLED4_SINK_REG_STR_CABC_MASK,
-						WLED4_SINK_REG_STR_CABC_MASK);
-			if (rc < 0)
+	if (wled->version == 4) {
+		for (i = 0; i < wled->cfg.num_strings; i++) {
+			if (sink_config &
+			    BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i))
+				val = WLED4_SINK_REG_STR_MOD_MASK;
+			else
+				/* Disable modulator_en for unused sink */
+				val = 0;
+
+			rc = regmap_write(wled->regmap, wled->sink_addr +
+					  WLED4_SINK_REG_STR_MOD_EN(i), val);
+			if (rc < 0) {
+				dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n",
+					rc);
 				goto failed_detect;
-		}
-
-		if (sink_config & BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i))
-			val = WLED4_SINK_REG_STR_MOD_MASK;
-		else
-			val = 0x0; /* Disable modulator_en for unused sink */
-
-		rc = regmap_write(wled->regmap, wled->sink_addr +
-				  WLED4_SINK_REG_STR_MOD_EN(i), val);
-		if (rc < 0) {
-			dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n",
-				rc);
-			goto failed_detect;
+			}
 		}
 	}
 
+	/* Enable CABC */
+	rc = wled->wled_cabc_config(wled, true);
+	if (rc < 0)
+		goto failed_detect;
+
 	/* Restore the feedback setting */
 	rc = regmap_write(wled->regmap,
 			  wled->ctrl_addr + WLED3_CTRL_REG_FEEDBACK_CONTROL, 0);
@@ -534,7 +612,8 @@ static void wled_auto_string_detection(struct wled *wled)
 
 #define WLED_AUTO_DETECT_OVP_COUNT		5
 #define WLED_AUTO_DETECT_CNT_DLY_US		USEC_PER_SEC
-static bool wled_auto_detection_required(struct wled *wled)
+
+static bool wled4_auto_detection_required(struct wled *wled)
 {
 	s64 elapsed_time_us;
 
@@ -570,29 +649,19 @@ static bool wled_auto_detection_required(struct wled *wled)
 static int wled_auto_detection_at_init(struct wled *wled)
 {
 	int rc;
-	u32 fault_status, rt_status;
+	bool fault_set;
 
 	if (!wled->cfg.auto_detection_enabled)
 		return 0;
 
-	rc = regmap_read(wled->regmap,
-			 wled->ctrl_addr + WLED3_CTRL_REG_INT_RT_STS,
-			 &rt_status);
-	if (rc < 0) {
-		dev_err(wled->dev, "Failed to read RT status rc=%d\n", rc);
-		return rc;
-	}
-
-	rc = regmap_read(wled->regmap,
-			 wled->ctrl_addr + WLED3_CTRL_REG_FAULT_STATUS,
-			 &fault_status);
+	rc = wled_ovp_fault_status(wled, &fault_set);
 	if (rc < 0) {
-		dev_err(wled->dev, "Failed to read fault status rc=%d\n", rc);
+		dev_err(wled->dev, "Error in getting OVP fault_sts, rc=%d\n",
+			rc);
 		return rc;
 	}
 
-	if ((rt_status & WLED3_CTRL_REG_OVP_FAULT_STATUS) ||
-	    (fault_status & WLED3_CTRL_REG_OVP_FAULT_BIT)) {
+	if (fault_set) {
 		mutex_lock(&wled->lock);
 		wled_auto_string_detection(wled);
 		mutex_unlock(&wled->lock);
@@ -629,7 +698,7 @@ static irqreturn_t wled_ovp_irq_handler(int irq, void *_wled)
 			int_sts, fault_sts);
 
 	if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT) {
-		if (wled_auto_detection_required(wled)) {
+		if (wled->wled_auto_detection_required(wled)) {
 			mutex_lock(&wled->lock);
 			wled_auto_string_detection(wled);
 			mutex_unlock(&wled->lock);
@@ -811,17 +880,12 @@ static int wled4_setup(struct wled *wled)
 					wled->cfg.string_i_limit);
 		if (rc < 0)
 			return rc;
-
-		addr = wled->sink_addr +
-				WLED4_SINK_REG_STR_CABC(j);
-		rc = regmap_update_bits(wled->regmap, addr,
-					WLED4_SINK_REG_STR_CABC_MASK,
-					wled->cfg.cabc ?
-					WLED4_SINK_REG_STR_CABC_MASK : 0);
-		if (rc < 0)
-			return rc;
 	}
 
+	rc = wled4_cabc_config(wled, wled->cfg.cabc);
+	if (rc < 0)
+		return rc;
+
 	rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
 				WLED3_CTRL_REG_MOD_EN,
 				WLED3_CTRL_REG_MOD_EN_MASK,
@@ -835,7 +899,7 @@ static int wled4_setup(struct wled *wled)
 	if (rc < 0)
 		return rc;
 
-	rc = wled_sync_toggle(wled);
+	rc = wled->wled_sync_toggle(wled);
 	if (rc < 0) {
 		dev_err(wled->dev, "Failed to toggle sync reg rc:%d\n", rc);
 		return rc;
@@ -943,7 +1007,7 @@ static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx)
 	return idx;
 }
 
-static int wled_configure(struct wled *wled, int version)
+static int wled_configure(struct wled *wled)
 {
 	struct wled_config *cfg = &wled->cfg;
 	struct device *dev = wled->dev;
@@ -1027,12 +1091,13 @@ static int wled_configure(struct wled *wled, int version)
 	if (rc)
 		wled->name = devm_kasprintf(dev, GFP_KERNEL, "%pOFn", dev->of_node);
 
-	switch (version) {
+	switch (wled->version) {
 	case 3:
 		u32_opts = wled3_opts;
 		size = ARRAY_SIZE(wled3_opts);
 		*cfg = wled3_config_defaults;
 		wled->wled_set_brightness = wled3_set_brightness;
+		wled->wled_sync_toggle = wled3_sync_toggle;
 		wled->max_string_count = 3;
 		wled->sink_addr = wled->ctrl_addr;
 		break;
@@ -1042,6 +1107,11 @@ static int wled_configure(struct wled *wled, int version)
 		size = ARRAY_SIZE(wled4_opts);
 		*cfg = wled4_config_defaults;
 		wled->wled_set_brightness = wled4_set_brightness;
+		wled->wled_sync_toggle = wled3_sync_toggle;
+		wled->wled_cabc_config = wled4_cabc_config;
+		wled->wled_ovp_delay = wled4_ovp_delay;
+		wled->wled_auto_detection_required =
+					wled4_auto_detection_required;
 		wled->max_string_count = 4;
 
 		prop_addr = of_get_address(dev->of_node, 1, NULL, NULL);
@@ -1178,7 +1248,6 @@ static int wled_probe(struct platform_device *pdev)
 	struct backlight_device *bl;
 	struct wled *wled;
 	struct regmap *regmap;
-	int version;
 	u32 val;
 	int rc;
 
@@ -1195,18 +1264,18 @@ static int wled_probe(struct platform_device *pdev)
 	wled->regmap = regmap;
 	wled->dev = &pdev->dev;
 
-	version = (uintptr_t)of_device_get_match_data(&pdev->dev);
-	if (!version) {
+	wled->version = (uintptr_t)of_device_get_match_data(&pdev->dev);
+	if (!wled->version) {
 		dev_err(&pdev->dev, "Unknown device version\n");
 		return -ENODEV;
 	}
 
 	mutex_init(&wled->lock);
-	rc = wled_configure(wled, version);
+	rc = wled_configure(wled);
 	if (rc)
 		return rc;
 
-	switch (version) {
+	switch (wled->version) {
 	case 3:
 		wled->cfg.auto_detection_enabled = false;
 		rc = wled3_setup(wled);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project

[PATCH V6 3/4] backlight: qcom-wled: Add WLED5 bindings

[Kiran Gunda]

Add WLED5 specific bindings.

Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
---
 .../bindings/leds/backlight/qcom-wled.yaml         | 59 ++++++++++++++++++++--
 1 file changed, 56 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
index b835443b..01c7d93 100644
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
@@ -21,6 +21,7 @@ properties:
       - qcom,pm8941-wled
       - qcom,pmi8998-wled
       - qcom,pm660l-wled
+      - qcom,pm8150l-wled
 
   reg:
     maxItems: 1
@@ -28,12 +29,13 @@ properties:
   default-brightness:
     description: |
       brightness value on boot.
-    minimum: 0
-    maximum: 4095
-    default: 2048
 
   label: true
 
+  max-brightness:
+    description: |
+      Maximum brightness level.
+
   qcom,cs-out:
     description: |
       enable current sink output.
@@ -141,6 +143,31 @@ properties:
       - const: ovp
       - const: short
 
+  qcom,modulator-sel:
+    description: |
+      Selects the modulator used for brightness modulation.
+      Allowed values are,
+           0 - Modulator A
+           1 - Modulator B
+      This property is applicable only to WLED5 peripheral.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 1 ]
+      - default: 0
+
+  qcom,cabc-sel:
+    description: |
+      Selects the CABC pin signal used for brightness modulation.
+      Allowed values are,
+           0 - CABC disabled
+           1 - CABC 1
+           2 - CABC 2
+           3 - External signal (e.g. LPG) is used for dimming
+      This property is applicable only to WLED5 peripheral.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 1, 2, 3 ]
+
 allOf:
   - if:
       properties:
@@ -183,6 +210,32 @@ allOf:
 
         interrupt-names:
           minItems: 2
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8150l-wled
+
+    then:
+      properties:
+        default-brightness:
+          minimum: 0
+          maximum: 32767
+
+        max-brightness:
+          minimum: 0
+          maximum: 32767
+
+    else:
+      properties:
+        default-brightness:
+          minimum: 0
+          maximum: 4095
+
+        max-brightness:
+          minimum: 0
+          maximum: 4095
 
 required:
   - compatible
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project

[PATCH V6 4/4] backlight: qcom-wled: Add support for WLED5 peripheral that is present on PM8150L PMICs

[Kiran Gunda]

From: Subbaraman Narayanamurthy <subbaram@codeaurora.org>

PM8150L WLED supports the following:
    - Two modulators and each sink can use any of the modulator
    - Multiple CABC selection options from which one can be selected/enabled
    - Multiple brightness width selection (12 bits to 15 bits)

Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
---
 drivers/video/backlight/qcom-wled.c | 378 +++++++++++++++++++++++++++++++++++-
 1 file changed, 376 insertions(+), 2 deletions(-)

diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c
index 7b0095e..c25c311 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c
@@ -15,16 +15,21 @@
 
 /* From DT binding */
 #define WLED_MAX_STRINGS				4
+#define MOD_A						0
+#define MOD_B						1
 
 #define WLED_DEFAULT_BRIGHTNESS				2048
 #define WLED_SOFT_START_DLY_US				10000
 #define WLED3_SINK_REG_BRIGHT_MAX			0xFFF
+#define WLED5_SINK_REG_BRIGHT_MAX_12B			0xFFF
+#define WLED5_SINK_REG_BRIGHT_MAX_15B			0x7FFF
 
 /* WLED3/WLED4 control registers */
 #define WLED3_CTRL_REG_FAULT_STATUS			0x08
 #define  WLED3_CTRL_REG_ILIM_FAULT_BIT			BIT(0)
 #define  WLED3_CTRL_REG_OVP_FAULT_BIT			BIT(1)
 #define  WLED4_CTRL_REG_SC_FAULT_BIT			BIT(2)
+#define  WLED5_CTRL_REG_OVP_PRE_ALARM_BIT		BIT(4)
 
 #define WLED3_CTRL_REG_INT_RT_STS			0x10
 #define  WLED3_CTRL_REG_OVP_FAULT_STATUS		BIT(1)
@@ -40,6 +45,7 @@
 
 #define WLED3_CTRL_REG_OVP				0x4d
 #define  WLED3_CTRL_REG_OVP_MASK			GENMASK(1, 0)
+#define  WLED5_CTRL_REG_OVP_MASK			GENMASK(3, 0)
 
 #define WLED3_CTRL_REG_ILIMIT				0x4e
 #define  WLED3_CTRL_REG_ILIMIT_MASK			GENMASK(2, 0)
@@ -101,6 +107,44 @@
 
 #define WLED4_SINK_REG_BRIGHT(n)			(0x57 + (n * 0x10))
 
+/* WLED5 specific control registers */
+#define WLED5_CTRL_REG_OVP_INT_CTL			0x5f
+#define  WLED5_CTRL_REG_OVP_INT_TIMER_MASK		GENMASK(2, 0)
+
+/* WLED5 specific sink registers */
+#define WLED5_SINK_REG_MOD_A_EN				0x50
+#define WLED5_SINK_REG_MOD_B_EN				0x60
+#define  WLED5_SINK_REG_MOD_EN_MASK			BIT(7)
+
+#define WLED5_SINK_REG_MOD_A_SRC_SEL			0x51
+#define WLED5_SINK_REG_MOD_B_SRC_SEL			0x61
+#define  WLED5_SINK_REG_MOD_SRC_SEL_HIGH		0
+#define  WLED5_SINK_REG_MOD_SRC_SEL_EXT			0x03
+#define  WLED5_SINK_REG_MOD_SRC_SEL_MASK		GENMASK(1, 0)
+
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL	0x52
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL	0x62
+#define  WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B		0
+#define  WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B		1
+
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB		0x53
+#define WLED5_SINK_REG_MOD_A_BRIGHTNESS_MSB		0x54
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB		0x63
+#define WLED5_SINK_REG_MOD_B_BRIGHTNESS_MSB		0x64
+
+#define WLED5_SINK_REG_MOD_SYNC_BIT			0x65
+#define  WLED5_SINK_REG_SYNC_MOD_A_BIT			BIT(0)
+#define  WLED5_SINK_REG_SYNC_MOD_B_BIT			BIT(1)
+#define  WLED5_SINK_REG_SYNC_MASK			GENMASK(1, 0)
+
+/* WLED5 specific per-'string' registers below */
+#define WLED5_SINK_REG_STR_FULL_SCALE_CURR(n)		(0x72 + (n * 0x10))
+
+#define WLED5_SINK_REG_STR_SRC_SEL(n)			(0x73 + (n * 0x10))
+#define  WLED5_SINK_REG_SRC_SEL_MOD_A			0
+#define  WLED5_SINK_REG_SRC_SEL_MOD_B			1
+#define  WLED5_SINK_REG_SRC_SEL_MASK			GENMASK(1, 0)
+
 struct wled_var_cfg {
 	const u32 *values;
 	u32 (*fn)(u32);
@@ -125,6 +169,8 @@ struct wled_config {
 	u32 num_strings;
 	u32 string_i_limit;
 	u32 enabled_strings[WLED_MAX_STRINGS];
+	u32 mod_sel;
+	u32 cabc_sel;
 	bool cs_out_en;
 	bool ext_gen;
 	bool cabc;
@@ -150,6 +196,7 @@ struct wled {
 	u32 version;
 	bool disabled_by_short;
 	bool has_short_detect;
+	bool cabc_disabled;
 	int short_irq;
 	int ovp_irq;
 
@@ -222,6 +269,28 @@ static int wled4_set_brightness(struct wled *wled, u16 brightness)
 	return 0;
 }
 
+static int wled5_set_brightness(struct wled *wled, u16 brightness)
+{
+	int rc, offset;
+	u16 low_limit = wled->max_brightness * 1 / 1000;
+	u8 v[2];
+
+	/* WLED5's lower limit is 0.1% */
+	if (brightness < low_limit)
+		brightness = low_limit;
+
+	v[0] = brightness & 0xff;
+	v[1] = (brightness >> 8) & 0x7f;
+
+	offset = (wled->cfg.mod_sel == MOD_A) ?
+		  WLED5_SINK_REG_MOD_A_BRIGHTNESS_LSB :
+		  WLED5_SINK_REG_MOD_B_BRIGHTNESS_LSB;
+
+	rc = regmap_bulk_write(wled->regmap, wled->sink_addr + offset,
+			       v, 2);
+	return rc;
+}
+
 static void wled_ovp_work(struct work_struct *work)
 {
 	struct wled *wled = container_of(work,
@@ -279,6 +348,24 @@ static int wled3_sync_toggle(struct wled *wled)
 	return rc;
 }
 
+static int wled5_sync_toggle(struct wled *wled)
+{
+	int rc;
+	u8 val;
+
+	val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT :
+					     WLED5_SINK_REG_SYNC_MOD_B_BIT;
+	rc = regmap_update_bits(wled->regmap,
+				wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
+				WLED5_SINK_REG_SYNC_MASK, val);
+	if (rc < 0)
+		return rc;
+
+	return regmap_update_bits(wled->regmap,
+				  wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT,
+				  WLED5_SINK_REG_SYNC_MASK, 0);
+}
+
 static int wled_ovp_fault_status(struct wled *wled, bool *fault_set)
 {
 	int rc;
@@ -304,7 +391,11 @@ static int wled_ovp_fault_status(struct wled *wled, bool *fault_set)
 	if (int_rt_sts & WLED3_CTRL_REG_OVP_FAULT_STATUS)
 		*fault_set = true;
 
-	if (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT)
+	if (wled->version == 4 && (fault_sts & WLED3_CTRL_REG_OVP_FAULT_BIT))
+		*fault_set = true;
+
+	if (wled->version == 5 && (fault_sts & (WLED3_CTRL_REG_OVP_FAULT_BIT |
+				   WLED5_CTRL_REG_OVP_PRE_ALARM_BIT)))
 		*fault_set = true;
 
 	if (*fault_set)
@@ -319,6 +410,26 @@ static int wled4_ovp_delay(struct wled *wled)
 	return WLED_SOFT_START_DLY_US;
 }
 
+static int wled5_ovp_delay(struct wled *wled)
+{
+	int rc, delay_us;
+	u32 val;
+	u8 ovp_timer_ms[8] = {1, 2, 4, 8, 12, 16, 20, 24};
+
+	/* For WLED5, get the delay based on OVP timer */
+	rc = regmap_read(wled->regmap, wled->ctrl_addr +
+			 WLED5_CTRL_REG_OVP_INT_CTL, &val);
+	if (rc < 0)
+		delay_us =
+		ovp_timer_ms[val & WLED5_CTRL_REG_OVP_INT_TIMER_MASK] * 1000;
+	else
+		delay_us = 2 * WLED_SOFT_START_DLY_US;
+
+	dev_dbg(wled->dev, "delay_time_us: %d\n", delay_us);
+
+	return delay_us;
+}
+
 static int wled_update_status(struct backlight_device *bl)
 {
 	struct wled *wled = bl_get_data(bl);
@@ -381,6 +492,31 @@ static int wled4_cabc_config(struct wled *wled, bool enable)
 	return 0;
 }
 
+static int wled5_cabc_config(struct wled *wled, bool enable)
+{
+	int rc, offset;
+	u8 reg;
+
+	if (wled->cabc_disabled)
+		return 0;
+
+	reg = enable ? wled->cfg.cabc_sel : 0;
+	offset = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_MOD_A_SRC_SEL :
+						WLED5_SINK_REG_MOD_B_SRC_SEL;
+
+	rc = regmap_update_bits(wled->regmap, wled->sink_addr + offset,
+				WLED5_SINK_REG_MOD_SRC_SEL_MASK, reg);
+	if (rc < 0) {
+		pr_err("Error in configuring CABC rc=%d\n", rc);
+		return rc;
+	}
+
+	if (!wled->cfg.cabc_sel)
+		wled->cabc_disabled = true;
+
+	return 0;
+}
+
 #define WLED_SHORT_DLY_MS			20
 #define WLED_SHORT_CNT_MAX			5
 #define WLED_SHORT_RESET_CNT_DLY_US		USEC_PER_SEC
@@ -646,6 +782,23 @@ static bool wled4_auto_detection_required(struct wled *wled)
 	return false;
 }
 
+static bool wled5_auto_detection_required(struct wled *wled)
+{
+	if (!wled->cfg.auto_detection_enabled)
+		return false;
+
+	/*
+	 * Unlike WLED4, WLED5 has OVP fault density interrupt configuration
+	 * i.e. to count the number of OVP alarms for a certain duration before
+	 * triggering OVP fault interrupt. By default, number of OVP fault
+	 * events counted before an interrupt is fired is 32 and the time
+	 * interval is 12 ms. If we see one OVP fault interrupt, then that
+	 * should qualify for a real OVP fault condition to run auto detection
+	 * algorithm.
+	 */
+	return true;
+}
+
 static int wled_auto_detection_at_init(struct wled *wled)
 {
 	int rc;
@@ -921,6 +1074,119 @@ static const struct wled_config wled4_config_defaults = {
 	.auto_detection_enabled = false,
 };
 
+static int wled5_setup(struct wled *wled)
+{
+	int rc, temp, i, j, offset;
+	u8 sink_en = 0;
+	u16 addr;
+	u32 val;
+
+	rc = regmap_update_bits(wled->regmap,
+				wled->ctrl_addr + WLED3_CTRL_REG_OVP,
+				WLED5_CTRL_REG_OVP_MASK, wled->cfg.ovp);
+	if (rc < 0)
+		return rc;
+
+	rc = regmap_update_bits(wled->regmap,
+				wled->ctrl_addr + WLED3_CTRL_REG_ILIMIT,
+				WLED3_CTRL_REG_ILIMIT_MASK,
+				wled->cfg.boost_i_limit);
+	if (rc < 0)
+		return rc;
+
+	rc = regmap_update_bits(wled->regmap,
+				wled->ctrl_addr + WLED3_CTRL_REG_FREQ,
+				WLED3_CTRL_REG_FREQ_MASK,
+				wled->cfg.switch_freq);
+	if (rc < 0)
+		return rc;
+
+	/* Per sink/string configuration */
+	for (i = 0; i < wled->cfg.num_strings; ++i) {
+		j = wled->cfg.enabled_strings[i];
+		addr = wled->sink_addr +
+				WLED4_SINK_REG_STR_FULL_SCALE_CURR(j);
+		rc = regmap_update_bits(wled->regmap, addr,
+					WLED4_SINK_REG_STR_FULL_SCALE_CURR_MASK,
+					wled->cfg.string_i_limit);
+		if (rc < 0)
+			return rc;
+
+		addr = wled->sink_addr + WLED5_SINK_REG_STR_SRC_SEL(j);
+		rc = regmap_update_bits(wled->regmap, addr,
+					WLED5_SINK_REG_SRC_SEL_MASK,
+					wled->cfg.mod_sel == MOD_A ?
+					WLED5_SINK_REG_SRC_SEL_MOD_A :
+					WLED5_SINK_REG_SRC_SEL_MOD_B);
+
+		temp = j + WLED4_SINK_REG_CURR_SINK_SHFT;
+		sink_en |= 1 << temp;
+	}
+
+	rc = wled5_cabc_config(wled, wled->cfg.cabc_sel ? true : false);
+	if (rc < 0)
+		return rc;
+
+	/* Enable one of the modulators A or B based on mod_sel */
+	addr = wled->sink_addr + WLED5_SINK_REG_MOD_A_EN;
+	val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_MOD_EN_MASK : 0;
+	rc = regmap_update_bits(wled->regmap, addr,
+				WLED5_SINK_REG_MOD_EN_MASK, val);
+	if (rc < 0)
+		return rc;
+
+	addr = wled->sink_addr + WLED5_SINK_REG_MOD_B_EN;
+	val = (wled->cfg.mod_sel == MOD_B) ? WLED5_SINK_REG_MOD_EN_MASK : 0;
+	rc = regmap_update_bits(wled->regmap, addr,
+				WLED5_SINK_REG_MOD_EN_MASK, val);
+	if (rc < 0)
+		return rc;
+
+	offset = (wled->cfg.mod_sel == MOD_A) ?
+		  WLED5_SINK_REG_MOD_A_BRIGHTNESS_WIDTH_SEL :
+		  WLED5_SINK_REG_MOD_B_BRIGHTNESS_WIDTH_SEL;
+
+	addr = wled->sink_addr + offset;
+	val = (wled->max_brightness == WLED5_SINK_REG_BRIGHT_MAX_15B) ?
+		 WLED5_SINK_REG_BRIGHTNESS_WIDTH_15B :
+		 WLED5_SINK_REG_BRIGHTNESS_WIDTH_12B;
+	rc = regmap_write(wled->regmap, addr, val);
+	if (rc < 0)
+		return rc;
+
+	rc = regmap_update_bits(wled->regmap,
+				wled->sink_addr + WLED4_SINK_REG_CURR_SINK,
+				WLED4_SINK_REG_CURR_SINK_MASK, sink_en);
+	if (rc < 0)
+		return rc;
+
+	/* This updates only FSC configuration in WLED5 */
+	rc = wled->wled_sync_toggle(wled);
+	if (rc < 0) {
+		pr_err("Failed to toggle sync reg rc:%d\n", rc);
+		return rc;
+	}
+
+	rc = wled_auto_detection_at_init(wled);
+	if (rc < 0)
+		return rc;
+
+	return 0;
+}
+
+static const struct wled_config wled5_config_defaults = {
+	.boost_i_limit = 5,
+	.string_i_limit = 10,
+	.ovp = 4,
+	.num_strings = 4,
+	.switch_freq = 11,
+	.mod_sel = 0,
+	.cabc_sel = 0,
+	.cabc = false,
+	.external_pfet = false,
+	.auto_detection_enabled = false,
+};
+
 static const u32 wled3_boost_i_limit_values[] = {
 	105, 385, 525, 805, 980, 1260, 1400, 1680,
 };
@@ -939,6 +1205,16 @@ static const struct wled_var_cfg wled4_boost_i_limit_cfg = {
 	.size = ARRAY_SIZE(wled4_boost_i_limit_values),
 };
 
+static inline u32 wled5_boost_i_limit_values_fn(u32 idx)
+{
+	return 525 + (idx * 175);
+}
+
+static const struct wled_var_cfg wled5_boost_i_limit_cfg = {
+	.fn = wled5_boost_i_limit_values_fn,
+	.size = 8,
+};
+
 static const u32 wled3_ovp_values[] = {
 	35, 32, 29, 27,
 };
@@ -957,6 +1233,21 @@ static const struct wled_var_cfg wled4_ovp_cfg = {
 	.size = ARRAY_SIZE(wled4_ovp_values),
 };
 
+static inline u32 wled5_ovp_values_fn(u32 idx)
+{
+	/*
+	 * 0000 - 38.5 V
+	 * 0001 - 37 V ..
+	 * 1111 - 16 V
+	 */
+	return 38500 - (idx * 1500);
+}
+
+static const struct wled_var_cfg wled5_ovp_cfg = {
+	.fn = wled5_ovp_values_fn,
+	.size = 16,
+};
+
 static u32 wled3_num_strings_values_fn(u32 idx)
 {
 	return idx + 1;
@@ -996,6 +1287,14 @@ static const struct wled_var_cfg wled4_string_i_limit_cfg = {
 	.size = ARRAY_SIZE(wled4_string_i_limit_values),
 };
 
+static const struct wled_var_cfg wled5_mod_sel_cfg = {
+	.size = 2,
+};
+
+static const struct wled_var_cfg wled5_cabc_sel_cfg = {
+	.size = 4,
+};
+
 static u32 wled_values(const struct wled_var_cfg *cfg, u32 idx)
 {
 	if (idx >= cfg->size)
@@ -1072,6 +1371,44 @@ static int wled_configure(struct wled *wled)
 		},
 	};
 
+	const struct wled_u32_opts wled5_opts[] = {
+		{
+			.name = "qcom,current-boost-limit",
+			.val_ptr = &cfg->boost_i_limit,
+			.cfg = &wled5_boost_i_limit_cfg,
+		},
+		{
+			.name = "qcom,current-limit-microamp",
+			.val_ptr = &cfg->string_i_limit,
+			.cfg = &wled4_string_i_limit_cfg,
+		},
+		{
+			.name = "qcom,ovp-millivolt",
+			.val_ptr = &cfg->ovp,
+			.cfg = &wled5_ovp_cfg,
+		},
+		{
+			.name = "qcom,switching-freq",
+			.val_ptr = &cfg->switch_freq,
+			.cfg = &wled3_switch_freq_cfg,
+		},
+		{
+			.name = "qcom,num-strings",
+			.val_ptr = &cfg->num_strings,
+			.cfg = &wled4_num_strings_cfg,
+		},
+		{
+			.name = "qcom,modulator-sel",
+			.val_ptr = &cfg->mod_sel,
+			.cfg = &wled5_mod_sel_cfg,
+		},
+		{
+			.name = "qcom,cabc-sel",
+			.val_ptr = &cfg->cabc_sel,
+			.cfg = &wled5_cabc_sel_cfg,
+		},
+	};
+
 	const struct wled_bool_opts bool_opts[] = {
 		{ "qcom,cs-out", &cfg->cs_out_en, },
 		{ "qcom,ext-gen", &cfg->ext_gen, },
@@ -1122,6 +1459,26 @@ static int wled_configure(struct wled *wled)
 		wled->sink_addr = be32_to_cpu(*prop_addr);
 		break;
 
+	case 5:
+		u32_opts = wled5_opts;
+		size = ARRAY_SIZE(wled5_opts);
+		*cfg = wled5_config_defaults;
+		wled->wled_set_brightness = wled5_set_brightness;
+		wled->wled_sync_toggle = wled5_sync_toggle;
+		wled->wled_cabc_config = wled5_cabc_config;
+		wled->wled_ovp_delay = wled5_ovp_delay;
+		wled->wled_auto_detection_required =
+					wled5_auto_detection_required;
+		wled->max_string_count = 4;
+
+		prop_addr = of_get_address(dev->of_node, 1, NULL, NULL);
+		if (!prop_addr) {
+			dev_err(wled->dev, "invalid IO resources\n");
+			return -EINVAL;
+		}
+		wled->sink_addr = be32_to_cpu(*prop_addr);
+		break;
+
 	default:
 		dev_err(wled->dev, "Invalid WLED version\n");
 		return -EINVAL;
@@ -1275,6 +1632,10 @@ static int wled_probe(struct platform_device *pdev)
 	if (rc)
 		return rc;
 
+	val = WLED3_SINK_REG_BRIGHT_MAX;
+	of_property_read_u32(pdev->dev.of_node, "max-brightness", &val);
+	wled->max_brightness = val;
+
 	switch (wled->version) {
 	case 3:
 		wled->cfg.auto_detection_enabled = false;
@@ -1294,6 +1655,18 @@ static int wled_probe(struct platform_device *pdev)
 		}
 		break;
 
+	case 5:
+		wled->has_short_detect = true;
+		if (wled->cfg.cabc_sel)
+			wled->max_brightness = WLED5_SINK_REG_BRIGHT_MAX_12B;
+
+		rc = wled5_setup(wled);
+		if (rc) {
+			dev_err(&pdev->dev, "wled5_setup failed\n");
+			return rc;
+		}
+		break;
+
 	default:
 		dev_err(wled->dev, "Invalid WLED version\n");
 		break;
@@ -1315,7 +1688,7 @@ static int wled_probe(struct platform_device *pdev)
 	memset(&props, 0, sizeof(struct backlight_properties));
 	props.type = BACKLIGHT_RAW;
 	props.brightness = val;
-	props.max_brightness = WLED3_SINK_REG_BRIGHT_MAX;
+	props.max_brightness = wled->max_brightness;
 	bl = devm_backlight_device_register(&pdev->dev, wled->name,
 					    &pdev->dev, wled,
 					    &wled_ops, &props);
@@ -1338,6 +1711,7 @@ static const struct of_device_id wled_match_table[] = {
 	{ .compatible = "qcom,pm8941-wled", .data = (void *)3 },
 	{ .compatible = "qcom,pmi8998-wled", .data = (void *)4 },
 	{ .compatible = "qcom,pm660l-wled", .data = (void *)4 },
+	{ .compatible = "qcom,pm8150l-wled", .data = (void *)5 },
 	{}
 };
 MODULE_DEVICE_TABLE(of, wled_match_table);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project

Re: [PATCH V6 4/4] backlight: qcom-wled: Add support for WLED5 peripheral that is present on PM8150L PMICs

[Daniel Thompson]

On Thu, Apr 23, 2020 at 09:03:37PM +0530, Kiran Gunda wrote:
> From: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> 
> PM8150L WLED supports the following:
>     - Two modulators and each sink can use any of the modulator
>     - Multiple CABC selection options from which one can be selected/enabled
>     - Multiple brightness width selection (12 bits to 15 bits)
> 
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>

Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>

Re: [PATCH V6 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format

[Lee Jones]

On Thu, 23 Apr 2020, Kiran Gunda wrote:

> Convert the qcom-wled bindings from .txt to .yaml format.
> Also replace PM8941 to WLED3 and PMI8998 to WLED4.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  .../bindings/leds/backlight/qcom-wled.txt          | 154 ---------------
>  .../bindings/leds/backlight/qcom-wled.yaml         | 208 +++++++++++++++++++++
>  2 files changed, 208 insertions(+), 154 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml

Needs a DT Ack.

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH V6 3/4] backlight: qcom-wled: Add WLED5 bindings

[Lee Jones]

On Thu, 23 Apr 2020, Kiran Gunda wrote:

> Add WLED5 specific bindings.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  .../bindings/leds/backlight/qcom-wled.yaml         | 59 ++++++++++++++++++++--
>  1 file changed, 56 insertions(+), 3 deletions(-)

Needs a DT Ack.

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH V6 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format

[Rob Herring]

On Thu, 23 Apr 2020 21:03:34 +0530, Kiran Gunda wrote:
> Convert the qcom-wled bindings from .txt to .yaml format.
> Also replace PM8941 to WLED3 and PMI8998 to WLED4.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  .../bindings/leds/backlight/qcom-wled.txt          | 154 ---------------
>  .../bindings/leds/backlight/qcom-wled.yaml         | 208 +++++++++++++++++++++
>  2 files changed, 208 insertions(+), 154 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH V6 3/4] backlight: qcom-wled: Add WLED5 bindings

[Rob Herring]

On Thu, 23 Apr 2020 21:03:36 +0530, Kiran Gunda wrote:
> Add WLED5 specific bindings.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  .../bindings/leds/backlight/qcom-wled.yaml         | 59 ++++++++++++++++++++--
>  1 file changed, 56 insertions(+), 3 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH V6 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format

[Lee Jones]

On Thu, 23 Apr 2020, Kiran Gunda wrote:

> Convert the qcom-wled bindings from .txt to .yaml format.
> Also replace PM8941 to WLED3 and PMI8998 to WLED4.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  .../bindings/leds/backlight/qcom-wled.txt          | 154 ---------------
>  .../bindings/leds/backlight/qcom-wled.yaml         | 208 +++++++++++++++++++++
>  2 files changed, 208 insertions(+), 154 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml

Applied, thanks.

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH V6 2/4] backlight: qcom-wled: Add callback functions

[Lee Jones]

On Thu, 23 Apr 2020, Kiran Gunda wrote:

> Add wled_cabc_config, wled_sync_toggle, wled_ovp_fault_status
> and wled_ovp_delay and wled_auto_detection_required callback
> functions to prepare the driver for adding WLED5 support.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  drivers/video/backlight/qcom-wled.c | 213 ++++++++++++++++++++++++------------
>  1 file changed, 141 insertions(+), 72 deletions(-)

Applied, thanks.

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH V6 3/4] backlight: qcom-wled: Add WLED5 bindings

[Lee Jones]

On Thu, 23 Apr 2020, Kiran Gunda wrote:

> Add WLED5 specific bindings.
> 
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
> ---
>  .../bindings/leds/backlight/qcom-wled.yaml         | 59 ++++++++++++++++++++--
>  1 file changed, 56 insertions(+), 3 deletions(-)

Applied, thanks.

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: [PATCH V6 4/4] backlight: qcom-wled: Add support for WLED5 peripheral that is present on PM8150L PMICs

[Lee Jones]

On Thu, 23 Apr 2020, Kiran Gunda wrote:

> From: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> 
> PM8150L WLED supports the following:
>     - Two modulators and each sink can use any of the modulator
>     - Multiple CABC selection options from which one can be selected/enabled
>     - Multiple brightness width selection (12 bits to 15 bits)
> 
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
> ---
>  drivers/video/backlight/qcom-wled.c | 378 +++++++++++++++++++++++++++++++++++-
>  1 file changed, 376 insertions(+), 2 deletions(-)

Applied, thanks.

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog