Re: [PATCH V4 3/4] backlight: qcom-wled: Add WLED5 bindings

[kgunda@codeaurora.org]

On 2020-03-31 23:26, Rob Herring wrote:
> On Mon, Mar 23, 2020 at 11:16:57PM +0530, Kiran Gunda wrote:
>> Add WLED5 specific bindings.
>> 
> 
> More of the same comments here...
> 
>> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
>> Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
>> ---
>>  .../bindings/leds/backlight/qcom-wled.yaml         | 39 
>> ++++++++++++++++++++++
>>  1 file changed, 39 insertions(+)
>> 
>> diff --git 
>> a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml 
>> b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
>> index 8a388bf..159115f 100644
>> --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
>> +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
>> @@ -20,6 +20,7 @@ properties:
>>         - qcom,pm8941-wled
>>         - qcom,pmi8998-wled
>>         - qcom,pm660l-wled
>> +       - qcom,pm8150l-wled
>> 
>>    reg:
>>      maxItems: 1
>> @@ -28,10 +29,23 @@ properties:
>>      maxItems: 1
>>      description:
>>        brightness value on boot, value from 0-4095.
>> +      For pm8150l this value vary from 0-4095 or 0-32767
>> +      depending on the brightness control mode. If CABC is
>> +      enabled 0-4095 range is used.
> 
> Constraints.
> 
Will address it in next post.
>>      allOf:
>>        - $ref: /schemas/types.yaml#/definitions/uint32
>>          default: 2048
>> 
>> +  max-brightness:
>> +    maxItems: 1
>> +    description:
>> +      Maximum brightness level. Allowed values are,
>> +      for pmi8998 it is  0-4095.
>> +      For pm8150l, this can be either 4095 or 32767.
> 
> Constraints!
> 
Will address it in next post.
>> +      If CABC is enabled, this is capped to 4095.
>> +    allOf:
>> +      - $ref: /schemas/types.yaml#/definitions/uint32
> 
> Standard property. Assume it has a type definition.'
> 
Will address it in next post.
>> +
>>    label:
>>      maxItems: 1
>>      description:
>> @@ -124,6 +138,31 @@ properties:
>>        value for PM8941 from 1 to 3. Default 2
>>        For PMI8998 from 1 to 4.
>> 
>> +  qcom,modulator-sel:
>> +    maxItems: 1
>> +    allOf:
>> +      - $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Selects the modulator used for brightness modulation.
>> +      Allowed values are,
>> +               0 - Modulator A
>> +               1 - Modulator B
>> +      If not specified, then modulator A will be used by default.
>> +      This property is applicable only to WLED5 peripheral.
>> +
>> +  qcom,cabc-sel:
>> +    maxItems: 1
>> +    allOf:
>> +      - $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Selects the CABC pin signal used for brightness modulation.
>> +      Allowed values are,
>> +              0 - CABC disabled
>> +              1 - CABC 1
>> +              2 - CABC 2
>> +              3 - External signal (e.g. LPG) is used for dimming
>> +      This property is applicable only to WLED5 peripheral.
>> +
>>    interrupts:
>>      maxItems: 2
>>      description:
>> --
>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora 
>> Forum,
>>  a Linux Foundation Collaborative Project
>>