Brian

On 7/9/19 12:48 PM, Brian Dodge wrote:
> FYI: please note that pSemi's legal department has informed me that 
> they do *not* want to keep the "ArcticSand" copyright notices and the 
> single pSemi line is appropriate.
>
Thanks for the follow up.  Lawyers can be fickle about this stuff.


> On Mon, Jul 8, 2019 at 2:02 PM Dan Murphy <dmurphy@ti.com 
> <mailto:dmurphy@ti.com>> wrote:
>
>     Brian
>
>     On 6/30/19 7:28 PM, Brian Dodge wrote:
>     > The vendor-prefixes.txt file properly refers to ArcticSand
>     > as arctic but the driver bindings improperly abbreviated the
>     > prefix to arc. This was a mistake in the original patch. This
>     > patch adds "arctic" and retains "arc" (deprecated) bindings
>     >
>     > Signed-off-by: Brian Dodge <bdodge09@gmail.com
>     <mailto:bdodge09@gmail.com>>
>     > ---
>     >   .../bindings/leds/backlight/arcxcnn_bl.txt         | 31
>     +++++++++++++++-------
>     >   1 file changed, 21 insertions(+), 10 deletions(-)
>     >
>     > diff --git
>     a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
>     b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
>     > index 230abde..4d98394 100644
>     > ---
>     a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
>     > +++
>     b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
>     > @@ -1,8 +1,13 @@
>     > -Binding for ArcticSand arc2c0608 LED driver
>     > +Binding for ArcticSand arc family LED drivers
>     >
>     >   Required properties:
>     > -- compatible:                should be "arc,arc2c0608"
>     > -- reg:                       slave address
>     > +- compatible: one of
>     > +     "arctic,arc1c0608"
>     > +     "arctic,arc2c0608"
>     > +     "arctic,arc3c0845"
>     > +     "arc,arc2c0608" (deprecated)
>     > +
>     > +- reg:               slave address
>     >
>     >   Optional properties:
>     >   - default-brightness:       brightness value on boot, value
>     from: 0-4095
>     > @@ -11,19 +16,25 @@ Optional properties:
>     >   - led-sources:              List of enabled channels from 0 to 5.
>     >                       See
>     Documentation/devicetree/bindings/leds/common.txt
>     >
>     > -- arc,led-config-0:  setting for register ILED_CONFIG_0
>     > -- arc,led-config-1:  setting for register ILED_CONFIG_1
>     > -- arc,dim-freq:              PWM mode frequence setting (bits
>     [3:0] used)
>     > -- arc,comp-config:   setting for register CONFIG_COMP
>     > -- arc,filter-config: setting for register FILTER_CONFIG
>     > -- arc,trim-config:   setting for register IMAXTUNE
>     > +- arctic,led-config-0:       setting for register ILED_CONFIG_0
>     > +- arctic,led-config-1:       setting for register ILED_CONFIG_1
>     > +- arctic,dim-freq:   PWM mode frequence setting (bits [3:0] used)
>     > +- arctic,comp-config:        setting for register CONFIG_COMP
>     > +- arctic,filter-config:      setting for register FILTER_CONFIG
>     > +- arctic,trim-config:        setting for register IMAXTUNE
>     > +- arc,led-config-0:  setting for register ILED_CONFIG_0
>     (deprecated)
>     > +- arc,led-config-1:  setting for register ILED_CONFIG_1
>     (deprecated)
>     > +- arc,dim-freq:              PWM mode frequence setting (bits
>     [3:0] used) (deprecated)
>     > +- arc,comp-config:   setting for register CONFIG_COMP (deprecated)
>     > +- arc,filter-config: setting for register FILTER_CONFIG
>     (deprecated)
>     > +- arc,trim-config:   setting for register IMAXTUNE (deprecated)
>     >
>     >   Note: Optional properties not specified will default to values
>     in IC EPROM
>     >
>     >   Example:
>     >
>     >   arc2c0608@30 {
>     > -     compatible = "arc,arc2c0608";
>     > +     compatible = "arctic,arc2c0608";
>     >       reg = <0x30>;
>     >       default-brightness = <500>;
>     >       label = "lcd-backlight";
>
>
>     Reviewed-by: Dan Murphy <dmurphy@ti.com <mailto:dmurphy@ti.com>>
>