From: Dan Murphy <dmurphy@ti.com>
To: Pavel Machek <pavel@ucw.cz>, <linux-omap@vger.kernel.org>,
<tony@atomide.com>, <sre@kernel.org>, <nekit1000@gmail.com>,
<mpartap@gmx.net>, <merlijn@wizzup.org>
Cc: <jacek.anaszewski@gmail.com>, <linux-kernel@vger.kernel.org>,
<linux-leds@vger.kernel.org>
Subject: Re: Backlight in motorola Droid 4
Date: Tue, 23 Jul 2019 10:53:16 -0500 [thread overview]
Message-ID: <b8fbc94f-c087-2c9d-4532-ea423f1626e6@ti.com> (raw)
In-Reply-To: <20190722205921.GA24787@amd>
Pavel
On 7/22/19 3:59 PM, Pavel Machek wrote:
> Hi!
>
> So now the backlight LED can be controlled. Good. (And thanks!)
>
> But I seem to remember that backlight had range from "is it really on?"
> to "very bright"; now it seems to have range from "bright" to "very
> bright".
>
> Any ideas what goes on there?
In the LM3552 driver we are changing the Full scale brightness registers
for the
specific control bank.
#define LM3532_REG_CTRL_A_BRT 0x17
#define LM3532_REG_CTRL_B_BRT 0x19
#define LM3532_REG_CTRL_C_BRT 0x1b
In the ti-lmu code the ALS zones were being modified not the control
bank brightness.
#define LM3532_REG_BRT_A 0x70 /* zone 0 */
#define LM3532_REG_BRT_B 0x76 /* zone 1 */
#define LM3532_REG_BRT_C 0x7C /* zone 2 */
Not sure how the ALS is attached in the system if it reports to the host
and the host manages
the back light or if the the ALS is connected directly to the LM3532.
Maybe the ALS zone targets need to be updated to allow a fuller range.
The LM3532 may be stuck
in a certain zone.
Probably should set up the ALS properties in the device tree.
Dan
> Thanks,
> Pavel
>
next prev parent reply other threads:[~2019-07-23 15:53 UTC|newest]
Thread overview: 106+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-19 16:26 [PATCH 0/2] LP5024/18 LED introduction Dan Murphy
2018-12-19 16:26 ` [PATCH 1/2] dt: bindings: lp5024: Introduce the lp5024 and lp5018 RGB driver Dan Murphy
2018-12-28 23:53 ` Rob Herring
2018-12-31 18:54 ` Dan Murphy
2019-01-08 20:33 ` Jacek Anaszewski
2019-01-08 20:53 ` Dan Murphy
2019-01-08 21:16 ` Jacek Anaszewski
2019-01-08 21:22 ` Dan Murphy
2019-01-09 20:12 ` Jacek Anaszewski
2019-01-09 21:12 ` Dan Murphy
2019-01-09 21:28 ` Jacek Anaszewski
2019-01-09 21:31 ` Dan Murphy
2019-01-10 18:44 ` Jacek Anaszewski
2019-01-10 19:22 ` Dan Murphy
2019-01-10 19:57 ` Jacek Anaszewski
2019-01-10 20:43 ` Dan Murphy
2019-01-10 22:03 ` Jacek Anaszewski
2019-01-10 23:51 ` Dan Murphy
2019-01-11 12:38 ` Dan Murphy
2019-01-11 21:52 ` Jacek Anaszewski
2019-01-12 17:09 ` Dan Murphy
2019-01-12 19:48 ` Jacek Anaszewski
2019-01-14 12:27 ` Dan Murphy
2019-01-14 20:11 ` Jacek Anaszewski
2019-01-14 20:14 ` Dan Murphy
2019-01-14 20:28 ` Jacek Anaszewski
2019-01-14 20:29 ` Dan Murphy
2018-12-19 16:26 ` [PATCH 2/2] leds: lp5024: Add the LP5024/18 RGB LED driver Dan Murphy
2018-12-19 19:04 ` Dan Murphy
2018-12-19 19:34 ` Pavel Machek
2018-12-19 19:41 ` Dan Murphy
2018-12-19 20:10 ` Pavel Machek
2018-12-19 20:41 ` Dan Murphy
2018-12-19 21:36 ` Jacek Anaszewski
2018-12-19 21:50 ` Dan Murphy
2018-12-20 12:40 ` Vesa Jääskeläinen
2018-12-20 13:56 ` Dan Murphy
2019-01-01 13:45 ` Vesa Jääskeläinen
2019-01-03 22:05 ` Jacek Anaszewski
2019-01-03 23:19 ` Vesa Jääskeläinen
2019-01-03 23:34 ` Pavel Machek
2019-01-04 19:49 ` Vesa Jääskeläinen
2019-01-04 20:43 ` Pavel Machek
2019-01-04 19:12 ` Jacek Anaszewski
2019-01-04 20:12 ` Pavel Machek
2019-01-04 21:37 ` Jacek Anaszewski
2019-01-04 22:07 ` Pavel Machek
2019-01-05 12:16 ` Jacek Anaszewski
2019-01-05 12:31 ` Pavel Machek
2019-01-05 13:16 ` Jacek Anaszewski
2019-01-05 22:12 ` Generic RGB LED support was " Pavel Machek
2019-01-06 15:52 ` Jacek Anaszewski
2019-01-07 19:13 ` Jacek Anaszewski
2019-01-07 19:36 ` Dan Murphy
2019-01-07 20:59 ` Jacek Anaszewski
2019-01-07 21:14 ` Dan Murphy
2019-01-08 21:18 ` Jacek Anaszewski
2019-01-08 21:25 ` Dan Murphy
2019-01-10 12:46 ` Dan Murphy
2019-01-10 19:23 ` Jacek Anaszewski
2019-01-10 19:58 ` Dan Murphy
2019-01-10 21:02 ` Jacek Anaszewski
2019-01-10 21:07 ` Dan Murphy
2019-01-08 22:59 ` Pavel Machek
2019-01-09 7:11 ` Vesa Jääskeläinen
2019-01-13 16:37 ` Jacek Anaszewski
2019-01-05 0:39 ` Vesa Jääskeläinen
2019-01-07 19:34 ` Dan Murphy
2019-01-09 6:20 ` Vesa Jääskeläinen
2019-01-07 21:13 ` Jacek Anaszewski
2019-01-07 21:15 ` Dan Murphy
2019-01-09 6:46 ` Vesa Jääskeläinen
2019-01-13 16:36 ` Jacek Anaszewski
2018-12-20 20:31 ` Jacek Anaszewski
2018-12-21 7:32 ` Jacek Anaszewski
2018-12-21 13:05 ` Dan Murphy
2018-12-29 18:28 ` Jacek Anaszewski
2018-12-29 19:07 ` Pavel Machek
2018-12-30 17:09 ` Jacek Anaszewski
2018-12-30 17:35 ` Pavel Machek
2018-12-31 15:43 ` Jacek Anaszewski
2018-12-31 15:47 ` Jacek Anaszewski
2018-12-31 19:15 ` Dan Murphy
2019-01-01 14:42 ` Jacek Anaszewski
2019-01-01 18:11 ` Dan Murphy
2019-01-01 22:06 ` Jacek Anaszewski
2018-12-31 16:28 ` Pavel Machek
2019-01-01 14:26 ` Jacek Anaszewski
2018-12-19 22:03 ` Pavel Machek
2018-12-19 22:08 ` Dan Murphy
2018-12-19 22:27 ` Pavel Machek
2018-12-20 1:31 ` Dan Murphy
2018-12-20 9:06 ` Pavel Machek
2018-12-20 14:03 ` Dan Murphy
2019-01-08 21:10 ` Jacek Anaszewski
2019-01-08 21:17 ` Dan Murphy
2019-07-22 20:59 ` Backlight in motorola Droid 4 Pavel Machek
2019-07-23 15:53 ` Dan Murphy [this message]
2019-07-24 8:22 ` Pavel Machek
2019-07-24 12:45 ` Pavel Machek
2019-07-24 15:10 ` Dan Murphy
2019-07-24 15:22 ` Dan Murphy
2019-07-26 14:38 ` Dan Murphy
2019-07-29 22:00 ` Pavel Machek
2019-07-30 18:21 ` Dan Murphy
2019-07-30 21:52 ` Pavel Machek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=b8fbc94f-c087-2c9d-4532-ea423f1626e6@ti.com \
--to=dmurphy@ti.com \
--cc=jacek.anaszewski@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=merlijn@wizzup.org \
--cc=mpartap@gmx.net \
--cc=nekit1000@gmail.com \
--cc=pavel@ucw.cz \
--cc=sre@kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).