From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> To: matti.vaittinen@fi.rohmeurope.com, mazziesaccount@gmail.com Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>, Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>, Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>, Lee Jones <lee.jones@linaro.org>, Michael Turquette <mturquette@baylibre.com>, Stephen Boyd <sboyd@kernel.org>, Linus Walleij <linus.walleij@linaro.org>, Bartosz Golaszewski <bgolaszewski@baylibre.com>, Liam Girdwood <lgirdwood@gmail.com>, Mark Brown <broonie@kernel.org>, Alessandro Zummo <a.zummo@towertech.it>, Alexandre Belloni <alexandre.belloni@bootlin.com>, Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>, linux-leds@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org, linux-gpio@vger.kernel.org, linux-rtc@vger.kernel.org Subject: [PATCH v10 00/13] Support ROHM BD71828 PMIC Date: Fri, 17 Jan 2020 11:30:02 +0200 Message-ID: <cover.1579249511.git.matti.vaittinen@fi.rohmeurope.com> (raw) Patch series introducing support for ROHM BD71828 PMIC ROHM BD71828 is a power management IC containing 7 bucks and 7 LDOs. All regulators can be controlled individually via I2C. Bucks 1,2,6 and 7 can also be assigned to a "regulator group" controlled by run-levels. Eg. Run level specific voltages and enable/disable statuses for each of these bucks can be set via register interface. The buck run-level group assignment (selection if buck is to be controlled individually or via run-levels) can be changed at run-time via I2C. This patch series brings only the basic support for controlling regulators individually via I2C. In addition to the bucks and LDOs there are: - The usual clk gate - 4 IO pins (mostly usable as GPO or tied to specific purpose) - power button support - RTC - two LEDs - battery charger - HALL sensor input This patch series adds support to regulators, clk, RTC, GPIOs and LEDs. Power-supply driver for charger is not included in this series. The series also adds LED DT-node lookup based on node name or given property name/value pair in LED core. It also adds generic default-state and default-trigger property handling to LED core. Follow-up patches simplifying few other LED drivers should follow. Changelog v10: - Split RTC patch to a BD70528 fix (which hopefully goes to 5.4) and to BD71828 support Changelog v9: (Changes suggested by Lee) - Added kerneldoc to struct rohm_dvs_config - cleaned few comments - updated copyright date - renamed variable 'mfd' to 'parent'. Changelog v8: LEDs: - Fixed bunch of typos. - Corrected the commit message which errorneously contained the 'leds-compatible' which I dropped in favour of match_property. - use max_brightness instead of LED_FULL if it is given when handling the default_state, "on". - clean fwnode_owned at the end of unsuccessfull registration or at the end of deregistration. - fix the accidental linuxdoc comment. - rename led_find_fwnode to led_get_fwnode as it increases refcount. Changelog v7: - Rebased on top of v5.5-rc2 - Dropped already applied patches - basic regulator support (in regulator tree now) - regulator dt-bindings (in regulator tree now) - gpio devm function documentation (in GPIO tree now) - Dropped new devm-variant of gpio_array getting for MFD sub-devices who have consumer information in parent DT node as gpio consumer was dropped from the series - removed extra line-breaks from MFD driver and Makefile - fixed RTC patch subject line (added missing colon) - included a patch which adds compatible for ROHM BD71850 PMIC Changelog v6: Rebased on top of v5.5-rc1 LED core: - Do new fw-node look-up only if the new match data is given. That way behaviour for existing drivers is not changed - Handle generic LED properties by core only if explisitly requested in init-data. That way behaviour for existing drivers is not changed until they are verified to work. BD71828 LEDs: - Fix module loading by adding "dummy" of_device_id table. DT bindings: All: - Remove regulator run-level properties as run-level support was dropped for now. - Change SPDX to dual lisence LED: - added select: false - replace oneOf + const by enum Regulator: - remove forgotten comments - comment indenting MFD: - remove unnecessary descriptions Regulators: - Dropped patch 12 with run-level controls - Dropped unnecessary ramp_delay_supported() - ram_delay ops were already only filled for DVS bucks. GPIO: - rename internal function. RTC: - Added missing blank line Changelog v5: Only LED patch (patch 15) changed, rest as in v4. LED: - Fixed issues reported by Dan Carpenter and kbuild-bot static analysis. Changelog v4 (first non RFC): General: - Changed subdevice loading and chip version identification to use platform ID. - License identifiers changed to GPL-2.0-only MFD: - Styling fixes mostly DT-Bindings: - a few more checks as suggested by Rob Herring. - Order of DT patches changed. - me as maintainer - standard units to new properties (microvolts, ohms) - runlevel values in an array LED: - BD71828 driver added (back) - Added DT support - Added LED DT node lookup in led framework when init_data is given with DT node match information. - Added common property parsing for default-state and default-trigger. Regulators: - dropped sysfs interfaces - fixed module unload/reload by binding gpio consumer information to regulator device not to MFD. GPIO: - Added devm_gpiod_get_parent_array - added few missing devm functions to documentation Changelog v3: DT-Bindings: - yamlify - add LED binding doc CLK: - Move clk register definitions from MFD headers to clk driver GPIO: - Add generic direction define and use it. LED: - Drop LED driver from the series (for now). Changelog v2: Mainly RTC and GPIO fixes suggested by Alexandre and Bartosz General: -Patch ordering changed to provide dt binding documents right after the MFD core. DT-Bindings for regulators (Patch 3) -Fix typo in PMIC model number RTC (patch 11) -Reverted renaming in order to reduce patch size. -Reworded commit message BD71828 regulator (patch 7) -Add MODULE_ALIAS GPIO (patch 12) -Remove file-name from comment -prefix IN and OUT defines with chip type -improved documentation for the INPUT only pin. -removed empty left-over function -removed unnecessary #ifdef CONFIG_OF_GPIO -removed unnecessary error print -Add MODULE_ALIAS Patch 1: dt-bindings for LEDs on BD71828 PMIC Patch 2: dt-bindings for BD71828 PMIC Patch 3: Convert rohm PMICs with common sub-devices to use platform_ device_id to match MFD sub-devices Patch 4: Add compatible for BD71850 Patch 5: BD71828 MFD core. Patch 6: Power button support using GPIO keys. Patch 7: CLK gate support using existing clk-bd718x7 Patch 8: Split existing bd718x7 regulator driver to generic ROHM dt parsing portion (used by more than one ROHM drivers) and bd718x8 specific parts Patch 9: Fix BD70528 RTC HOUR mask Patch 10: Support BD71828 RTC block using BD70528 RTC driver Patch 11: Allow control of GP(I)O pins on BD71828 via GPIO subsystem Patch 12: Add LED node lookup and common LED binding parsing support to LED class/core Patch 13: Support toggling the LEDs on BD71828. --- Matti Vaittinen (13): dt-bindings: leds: ROHM BD71282 PMIC LED driver dt-bindings: mfd: Document ROHM BD71828 bindings mfd: rohm PMICs - use platform_device_id to match MFD sub-devices mfd: bd718x7: Add compatible for BD71850 mfd: bd71828: Support ROHM BD71828 PMIC - core mfd: input: bd71828: Add power-key support clk: bd718x7: Support ROHM BD71828 clk block regulator: bd718x7: Split driver to common and bd718x7 specific parts mfd: bd70528: Fix hour register mask rtc: bd70528: add BD71828 support gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs leds: Add common LED binding parsing support to LED class/core led: bd71828: Support LED outputs on ROHM BD71828 PMIC .../bindings/leds/rohm,bd71828-leds.yaml | 52 +++ .../bindings/mfd/rohm,bd71828-pmic.yaml | 193 ++++++++ drivers/clk/Kconfig | 6 +- drivers/clk/clk-bd718x7.c | 50 ++- drivers/gpio/Kconfig | 12 + drivers/gpio/Makefile | 1 + drivers/gpio/gpio-bd71828.c | 159 +++++++ drivers/leds/Kconfig | 10 + drivers/leds/Makefile | 1 + drivers/leds/led-class.c | 115 ++++- drivers/leds/led-core.c | 258 +++++++++-- drivers/leds/leds-bd71828.c | 118 +++++ drivers/mfd/Kconfig | 15 + drivers/mfd/Makefile | 1 + drivers/mfd/rohm-bd70528.c | 3 +- drivers/mfd/rohm-bd71828.c | 344 ++++++++++++++ drivers/mfd/rohm-bd718x7.c | 43 +- drivers/regulator/Kconfig | 4 + drivers/regulator/Makefile | 1 + drivers/regulator/bd718x7-regulator.c | 200 +++------ drivers/regulator/rohm-regulator.c | 95 ++++ drivers/rtc/Kconfig | 3 +- drivers/rtc/rtc-bd70528.c | 220 +++++++-- include/linux/leds.h | 94 +++- include/linux/mfd/rohm-bd70528.h | 19 +- include/linux/mfd/rohm-bd71828.h | 423 ++++++++++++++++++ include/linux/mfd/rohm-bd718x7.h | 6 - include/linux/mfd/rohm-generic.h | 70 ++- include/linux/mfd/rohm-shared.h | 21 + 29 files changed, 2248 insertions(+), 289 deletions(-) create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml create mode 100644 drivers/gpio/gpio-bd71828.c create mode 100644 drivers/leds/leds-bd71828.c create mode 100644 drivers/mfd/rohm-bd71828.c create mode 100644 drivers/regulator/rohm-regulator.c create mode 100644 include/linux/mfd/rohm-bd71828.h create mode 100644 include/linux/mfd/rohm-shared.h base-commit: b3a987b0264d ("Linux 5.5-rc6") -- 2.21.0 -- Matti Vaittinen, Linux device drivers ROHM Semiconductors, Finland SWDC Kiviharjunlenkki 1E 90220 OULU FINLAND ~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~ Simon says - in Latin please. ~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~ Thanks to Simon Glass for the translation =]
next reply index Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-01-17 9:30 Matti Vaittinen [this message] 2020-01-17 9:31 ` [PATCH v10 01/13] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen 2020-01-17 9:32 ` [PATCH v10 02/13] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen 2020-01-17 9:34 ` [PATCH v10 03/13] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen 2020-01-17 9:35 ` [PATCH v10 04/13] mfd: bd718x7: Add compatible for BD71850 Matti Vaittinen 2020-01-17 9:36 ` [PATCH v10 05/13] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen 2020-01-17 9:36 ` [PATCH v10 06/13] mfd: input: bd71828: Add power-key support Matti Vaittinen 2020-01-17 9:37 ` [PATCH v10 07/13] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen 2020-01-17 9:38 ` [PATCH v10 08/13] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen 2020-01-17 10:28 ` Lee Jones 2020-01-17 10:43 ` Vaittinen, Matti 2020-01-17 13:40 ` Lee Jones 2020-01-20 7:06 ` Vaittinen, Matti 2020-01-17 9:40 ` [PATCH v10 09/13] mfd: bd70528: Fix hour register mask Matti Vaittinen 2020-01-17 10:21 ` Lee Jones 2020-01-17 9:42 ` [PATCH v10 10/13] rtc: bd70528: add BD71828 support Matti Vaittinen 2020-01-17 9:42 ` [PATCH v10 11/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen 2020-01-17 10:21 ` Lee Jones 2020-01-20 6:48 ` Vaittinen, Matti 2020-01-20 8:02 ` Lee Jones 2020-01-23 15:18 ` Linus Walleij 2020-01-17 9:43 ` [PATCH v10 12/13] leds: Add common LED binding parsing support to LED class/core Matti Vaittinen 2020-01-20 8:56 ` Vaittinen, Matti 2020-01-17 9:44 ` [PATCH v10 13/13] led: bd71828: Support LED outputs on ROHM BD71828 PMIC Matti Vaittinen 2020-01-17 10:30 ` [PATCH v10 00/13] Support " Lee Jones 2020-01-17 10:48 ` Vaittinen, Matti 2020-01-17 13:44 ` Lee Jones 2020-02-26 13:42 ` Pavel Machek 2020-02-26 14:25 ` Vaittinen, Matti
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=cover.1579249511.git.matti.vaittinen@fi.rohmeurope.com \ --to=matti.vaittinen@fi.rohmeurope.com \ --cc=a.zummo@towertech.it \ --cc=alexandre.belloni@bootlin.com \ --cc=bgolaszewski@baylibre.com \ --cc=broonie@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=dmurphy@ti.com \ --cc=jacek.anaszewski@gmail.com \ --cc=lee.jones@linaro.org \ --cc=lgirdwood@gmail.com \ --cc=linus.walleij@linaro.org \ --cc=linux-clk@vger.kernel.org \ --cc=linux-gpio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-leds@vger.kernel.org \ --cc=linux-rtc@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=mazziesaccount@gmail.com \ --cc=mturquette@baylibre.com \ --cc=pavel@ucw.cz \ --cc=robh+dt@kernel.org \ --cc=sboyd@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
Linux-LEDs Archive on lore.kernel.org Archives are clonable: git clone --mirror https://lore.kernel.org/linux-leds/0 linux-leds/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 linux-leds linux-leds/ https://lore.kernel.org/linux-leds \ linux-leds@vger.kernel.org public-inbox-index linux-leds Example config snippet for mirrors Newsgroup available over NNTP: nntp://nntp.lore.kernel.org/org.kernel.vger.linux-leds AGPL code for this site: git clone https://public-inbox.org/public-inbox.git