From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from smtp-4.sys.kth.se ([130.237.48.193]:54334 "EHLO smtp-4.sys.kth.se" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751960AbdK2ToF (ORCPT ); Wed, 29 Nov 2017 14:44:05 -0500 From: =?UTF-8?q?Niklas=20S=C3=B6derlund?= To: Laurent Pinchart , Hans Verkuil , linux-media@vger.kernel.org Cc: linux-renesas-soc@vger.kernel.org, tomoharu.fukawa.eb@renesas.com, Kieran Bingham , =?UTF-8?q?Niklas=20S=C3=B6derlund?= , Rob Herring , devicetree@vger.kernel.org Subject: [PATCH v8 01/28] rcar-vin: add Gen3 devicetree bindings documentation Date: Wed, 29 Nov 2017 20:43:15 +0100 Message-Id: <20171129194342.26239-2-niklas.soderlund+renesas@ragnatech.se> In-Reply-To: <20171129194342.26239-1-niklas.soderlund+renesas@ragnatech.se> References: <20171129194342.26239-1-niklas.soderlund+renesas@ragnatech.se> MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Sender: linux-media-owner@vger.kernel.org List-ID: Document the devicetree bindings for the CSI-2 inputs available on Gen3. There is a need to add a custom property 'renesas,id' and to define which CSI-2 input is described in which endpoint under the port@1 node. This information is needed since there are a set of predefined routes between each VIN and CSI-2 block. This routing table will be kept inside the driver but in order for it to act on it it must know which VIN and CSI-2 is which. Signed-off-by: Niklas Söderlund Acked-by: Rob Herring --- .../devicetree/bindings/media/rcar_vin.txt | 116 ++++++++++++++++++--- 1 file changed, 104 insertions(+), 12 deletions(-) diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index ff9697ed81396e64..5a95d9668d2c7dfd 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -2,8 +2,12 @@ Renesas R-Car Video Input driver (rcar_vin) ------------------------------------------- The rcar_vin device provides video input capabilities for the Renesas R-Car -family of devices. The current blocks are always slaves and suppot one input -channel which can be either RGB, YUYV or BT656. +family of devices. + +Each VIN instance has a single parallel input that supports RGB and YUV video, +with both external synchronization and BT.656 synchronization for the latter. +Depending on the instance the VIN input is connected to external SoC pins, or +on Gen3 to a CSI-2 receiver. - compatible: Must be one or more of the following - "renesas,vin-r8a7743" for the R8A7743 device @@ -31,21 +35,38 @@ channel which can be either RGB, YUYV or BT656. Additionally, an alias named vinX will need to be created to specify which video input device this is. -The per-board settings: +The per-board settings Gen2: - port sub-node describing a single endpoint connected to the vin as described in video-interfaces.txt[1]. Only the first one will be considered as each vin interface has one input port. - These settings are used to work out video input format and widths - into the system. +The per-board settings Gen3: + +Gen3 can support both a single connected parallel input source from +external SoC pins (port0) and/or multiple parallel input sources from +local SoC CSI-2 receivers (port1) depending on SoC. +- renesas,id - ID number of the VIN, VINx in the documentation. +- ports + - port0 - sub-node describing a single endpoint connected to the VIN + from external SoC pins described in video-interfaces.txt[1]. Only + the first one will be considered as each VIN interface has at most + one set of SoC external input pins. + - port1 - sub-nodes describing one or more endpoints connected to + the VIN from local SoC CSI-2 receivers. The endpoint numbers must + use the following schema. -Device node example -------------------- + - Endpoint 0 - sub-node describing the endpoint which is CSI20 + - Endpoint 1 - sub-node describing the endpoint which is CSI21 + - Endpoint 2 - sub-node describing the endpoint which is CSI40 + - Endpoint 3 - sub-node describing the endpoint which is CSI41 - aliases { - vin0 = &vin0; - }; +Device node example Gen2 +------------------------ + + aliases { + vin0 = &vin0; + }; vin0: vin@0xe6ef0000 { compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin"; @@ -55,8 +76,8 @@ Device node example status = "disabled"; }; -Board setup example (vin1 composite video input) ------------------------------------------------- +Board setup example Gen2 (vin1 composite video input) +----------------------------------------------------- &i2c2 { status = "ok"; @@ -95,6 +116,77 @@ Board setup example (vin1 composite video input) }; }; +Device node example Gen3 +------------------------ + + vin0: video@e6ef0000 { + compatible = "renesas,vin-r8a7795"; + reg = <0 0xe6ef0000 0 0x1000>; + interrupts = ; + clocks = <&cpg CPG_MOD 811>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 811>; + renesas,id = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin0csi20: endpoint@0 { + reg = <0>; + remote-endpoint= <&csi20vin0>; + }; + vin0csi21: endpoint@1 { + reg = <1>; + remote-endpoint= <&csi21vin0>; + }; + vin0csi40: endpoint@2 { + reg = <2>; + remote-endpoint= <&csi40vin0>; + }; + }; + }; + }; + + csi20: csi2@fea80000 { + compatible = "renesas,r8a7795-csi2"; + reg = <0 0xfea80000 0 0x10000>; + interrupts = ; + clocks = <&cpg CPG_MOD 714>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 714>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + csi20_in: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&adv7482_txb>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + csi20vin0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vin0csi20>; + }; + }; + }; + }; [1] video-interfaces.txt common video media interface -- 2.15.0