From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from mail-lf0-f68.google.com ([209.85.215.68]:43509 "EHLO mail-lf0-f68.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752470AbdLHMzj (ORCPT ); Fri, 8 Dec 2017 07:55:39 -0500 Received: by mail-lf0-f68.google.com with SMTP id 94so11780597lfy.10 for ; Fri, 08 Dec 2017 04:55:38 -0800 (PST) From: "Niklas =?iso-8859-1?Q?S=F6derlund?=" Date: Fri, 8 Dec 2017 13:55:32 +0100 To: Laurent Pinchart Cc: Hans Verkuil , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, tomoharu.fukawa.eb@renesas.com, Kieran Bingham Subject: Re: [PATCH v9 01/28] rcar-vin: add Gen3 devicetree bindings documentation Message-ID: <20171208125532.GL31989@bigcity.dyn.berto.se> References: <20171208010842.20047-1-niklas.soderlund+renesas@ragnatech.se> <20171208010842.20047-2-niklas.soderlund+renesas@ragnatech.se> <1516159.4MxLsDy55H@avalon> MIME-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Disposition: inline Content-Transfer-Encoding: 8bit In-Reply-To: <1516159.4MxLsDy55H@avalon> Sender: linux-media-owner@vger.kernel.org List-ID: Hi Laurent, Thanks for your comments! On 2017-12-08 09:46:24 +0200, Laurent Pinchart wrote: > Hi Niklas, > > Thank you for the patch. > > On Friday, 8 December 2017 03:08:15 EET Niklas Söderlund wrote: > > Document the devicetree bindings for the CSI-2 inputs available on Gen3. > > > > There is a need to add a custom property 'renesas,id' and to define > > which CSI-2 input is described in which endpoint under the port@1 node. > > This information is needed since there are a set of predefined routes > > between each VIN and CSI-2 block. This routing table will be kept > > inside the driver but in order for it to act on it it must know which > > VIN and CSI-2 is which. > > > > Signed-off-by: Niklas Söderlund > > Acked-by: Rob Herring > > --- > > .../devicetree/bindings/media/rcar_vin.txt | 116 +++++++++++++++--- > > 1 file changed, 104 insertions(+), 12 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt > > b/Documentation/devicetree/bindings/media/rcar_vin.txt index > > ff9697ed81396e64..5a95d9668d2c7dfd 100644 > > --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > > +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > > @@ -2,8 +2,12 @@ Renesas R-Car Video Input driver (rcar_vin) > > ------------------------------------------- > > > > The rcar_vin device provides video input capabilities for the Renesas R-Car > > -family of devices. The current blocks are always slaves and suppot one > > input > > -channel which can be either RGB, YUYV or BT656. > > +family of devices. > > + > > +Each VIN instance has a single parallel input that supports RGB and YUV > > video, > > +with both external synchronization and BT.656 synchronization for the > > latter. > > +Depending on the instance the VIN input is connected to external SoC pins, > > or > > +on Gen3 to a CSI-2 receiver. > > > > - compatible: Must be one or more of the following > > - "renesas,vin-r8a7743" for the R8A7743 device > > @@ -31,21 +35,38 @@ channel which can be either RGB, YUYV or BT656. > > Additionally, an alias named vinX will need to be created to specify > > which video input device this is. > > > > -The per-board settings: > > +The per-board settings Gen2: > > Nitpicking, s/Gen2/for Gen2 platforms/ > > (or Gen2 hardware, or Gen2 systems, pick the one you like best) Good catch, I guess I'm to caught up in it all and it's obvious for me what Gen2 is :-) I will update and use "Gen2 platform" throughout this document. > > > - port sub-node describing a single endpoint connected to the vin > > as described in video-interfaces.txt[1]. Only the first one will > > be considered as each vin interface has one input port. > > > > - These settings are used to work out video input format and widths > > - into the system. > > +The per-board settings Gen3: > > Ditto. > > > + > > +Gen3 can support both a single connected parallel input source from > > +external SoC pins (port0) and/or multiple parallel input sources from > > +local SoC CSI-2 receivers (port1) depending on SoC. > > > > +- renesas,id - ID number of the VIN, VINx in the documentation. > > +- ports > > + - port0 - sub-node describing a single endpoint connected to the VIN > > + from external SoC pins described in video-interfaces.txt[1]. Only > > + the first one will be considered as each VIN interface has at most > > + one set of SoC external input pins. > > s/port0/port 0/ or s/port0/port@0/ I will use 'port 0' as I think it makes more sens when reading. > > I'd go further than that and make it invalid to have multiple endpoints > instead of ignoring all but the first one. Good catch, I'm describing what the current rcar-vin driver dose and not the generic case where in fact only one endpoint in port 0 is valid. Will update. > > I would also explicitly state that VIN instances not connected to external > pins shall have no port 0. It's good to be explicit, will add this. > > > + - port1 - sub-nodes describing one or more endpoints connected to > > + the VIN from local SoC CSI-2 receivers. The endpoint numbers must > > + use the following schema. > > Nitpicking again, the Gen2-specific properties are indented above while the > Gen3 properties are not indented here. Pick the one you prefer :-) I like it they way it is :-) The Gen2-specific properties are all on the same level in the dt description. While some Gen3-specific properties (port 0 and port 1) are indented one level in the dt description and this is why I indented them one level in the documentation. To make it clear that they should be children of the ports node. I don't feel strongly about this but I feel it adds to the readability. If you don't agree I'm happy to remove the indentation for these two properties. > > > -Device node example > > -------------------- > > + - Endpoint 0 - sub-node describing the endpoint which is CSI20 > > + - Endpoint 1 - sub-node describing the endpoint which is CSI21 > > + - Endpoint 2 - sub-node describing the endpoint which is CSI40 > > + - Endpoint 3 - sub-node describing the endpoint which is CSI41 > > How about s/which is/connected to/ ? Sounds better, will update. > > > - aliases { > > - vin0 = &vin0; > > - }; > > +Device node example Gen2 > > s/Gen2/for Gen2 platforms/ > > and same in a few places below. Will fix. > > > +------------------------ > > + > > + aliases { > > + vin0 = &vin0; > > + }; > > This is unrelated, but do we need aliases ? We don't have aliases for Gen3 but they exists in DTS for Gen2. My feeling is that we don't need them. My plan is to once Gen3 support is done try to sort this out, both in the documentation and in the dts files for Gen2. > > > vin0: vin@0xe6ef0000 { > > compatible = "renesas,vin-r8a7790", > > "renesas,rcar-gen2-vin"; @@ -55,8 +76,8 @@ Device node example > > status = "disabled"; > > }; > > > > -Board setup example (vin1 composite video input) > > ------------------------------------------------- > > +Board setup example Gen2 (vin1 composite video input) > > +----------------------------------------------------- > > > > &i2c2 { > > status = "ok"; > > @@ -95,6 +116,77 @@ Board setup example (vin1 composite video input) > > }; > > }; > > > > +Device node example Gen3 > > +------------------------ > > + > > + vin0: video@e6ef0000 { > > + compatible = "renesas,vin-r8a7795"; > > + reg = <0 0xe6ef0000 0 0x1000>; > > + interrupts = ; > > + clocks = <&cpg CPG_MOD 811>; > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > + resets = <&cpg 811>; > > + renesas,id = <0>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port@1 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + reg = <1>; > > + > > + vin0csi20: endpoint@0 { > > + reg = <0>; > > + remote-endpoint= <&csi20vin0>; > > + }; > > + vin0csi21: endpoint@1 { > > + reg = <1>; > > + remote-endpoint= <&csi21vin0>; > > + }; > > + vin0csi40: endpoint@2 { > > + reg = <2>; > > + remote-endpoint= <&csi40vin0>; > > + }; > > + }; > > + }; > > + }; > > + > > + csi20: csi2@fea80000 { > > + compatible = "renesas,r8a7795-csi2"; > > + reg = <0 0xfea80000 0 0x10000>; > > + interrupts = ; > > + clocks = <&cpg CPG_MOD 714>; > > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; > > + resets = <&cpg 714>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port@0 { > > + reg = <0>; > > + csi20_in: endpoint { > > + clock-lanes = <0>; > > + data-lanes = <1>; > > + remote-endpoint = <&adv7482_txb>; > > + }; > > + }; > > + > > + port@1 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > > > + reg = <1>; > > + > > + csi20vin0: endpoint@0 { > > + reg = <0>; > > + remote-endpoint = <&vin0csi20>; > > + }; > > + }; > > + }; > > + }; > > > > [1] video-interfaces.txt common video media interface > > -- > Regards, > > Laurent Pinchart > -- Regards, Niklas Söderlund