From: Marco Felsch <m.felsch@pengutronix.de>
To: mchehab@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com,
sakari.ailus@linux.intel.com
Cc: devicetree@vger.kernel.org, p.zabel@pengutronix.de,
javierm@redhat.com, afshin.nasser@gmail.com,
laurent.pinchart@ideasonboard.com, linux-media@vger.kernel.org,
kernel@pengutronix.de, Rob Herring <robh@kernel.org>
Subject: [PATCH v4 3/7] media: dt-bindings: tvp5150: Add input port connectors DT bindings
Date: Tue, 29 Jan 2019 17:07:53 +0100 [thread overview]
Message-ID: <20190129160757.2314-4-m.felsch@pengutronix.de> (raw)
In-Reply-To: <20190129160757.2314-1-m.felsch@pengutronix.de>
The TVP5150/1 decoders support different video input sources to their
AIP1A/B pins.
Possible configurations are as follows:
- Analog Composite signal connected to AIP1A.
- Analog Composite signal connected to AIP1B.
- Analog S-Video Y (luminance) and C (chrominance)
signals connected to AIP1A and AIP1B respectively.
This patch extends the device tree bindings documentation to describe
how the input connectors for these devices should be defined in a DT.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changelog:
v3:
- remove examples for one and two inputs
- replace space by tabs
v2:
- adapt port layout in accordance with
https://www.spinics.net/lists/linux-media/msg138546.html with the
svideo-connector deviation (use only one endpoint)
.../devicetree/bindings/media/i2c/tvp5150.txt | 92 +++++++++++++++++--
1 file changed, 85 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
index 8c0fc1a26bf0..bdd273d8b44d 100644
--- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -12,11 +12,31 @@ Optional Properties:
- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
-The device node must contain one 'port' child node for its digital output
-video port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
+The device node must contain one 'port' child node per device physical input
+and output port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows
-Required Endpoint Properties for parallel synchronization:
+ Name Type Port
+ --------------------------------------
+ AIP1A sink 0
+ AIP1B sink 1
+ Y-OUT src 2
+
+The device node must contain at least one sink port and the src port. Each input
+port must be linked to an endpoint defined in
+Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. The
+port/connector layout is as follows
+
+tvp-5150 port@0 (AIP1A)
+ endpoint@0 -----------> Comp0-Con port
+ endpoint@1 -----------> Svideo-Con port
+tvp-5150 port@1 (AIP1B)
+ endpoint -----------> Comp1-Con port
+tvp-5150 port@2
+ endpoint (video bitstream output at YOUT[0-7] parallel bus)
+
+Required Endpoint Properties for parallel synchronization on output port:
- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
@@ -26,17 +46,75 @@ Required Endpoint Properties for parallel synchronization:
If none of hsync-active, vsync-active and field-even-active is specified,
the endpoint is assumed to use embedded BT.656 synchronization.
-Example:
+Example - three input sources:
+
+comp_connector_0 {
+ compatible = "composite-video-connector";
+ label = "Composite0";
+
+ port {
+ composite0_to_tvp5150: endpoint {
+ remote-endpoint = <&tvp5150_to_composite0>;
+ };
+ };
+};
+
+comp_connector_1 {
+ compatible = "composite-video-connector";
+ label = "Composite1";
+
+ port {
+ composite1_to_tvp5150: endpoint {
+ remote-endpoint = <&tvp5150_to_composite1>;
+ };
+ };
+};
+
+svid_connector {
+ compatible = "svideo-connector";
+ label = "S-Video";
+
+ port {
+ svideo_to_tvp5150: endpoint {
+ remote-endpoint = <&tvp5150_to_svideo>;
+ };
+ };
+};
&i2c2 {
- ...
tvp5150@5c {
compatible = "ti,tvp5150";
reg = <0x5c>;
pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
- port {
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tvp5150_to_composite0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&composite0_to_tvp5150>;
+ };
+
+ tvp5150_to_svideo: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&svideo_to_tvp5150>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tvp5150_to_composite1: endpoint {
+ remote-endpoint = <&composite1_to_tvp5150>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
tvp5150_1: endpoint {
remote-endpoint = <&ccdc_ep>;
};
--
2.20.1
next prev parent reply other threads:[~2019-01-29 16:08 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-29 16:07 [PATCH v4 0/7] TVP5150 new features Marco Felsch
2019-01-29 16:07 ` [PATCH v4 1/7] partial revert of "[media] tvp5150: add HW input connectors support" Marco Felsch
2019-01-29 16:07 ` [PATCH v4 2/7] media: tvp5150: add input source selection of_graph support Marco Felsch
2019-03-21 13:03 ` Jacopo Mondi
2019-03-27 16:22 ` Marco Felsch
2019-01-29 16:07 ` Marco Felsch [this message]
2019-01-29 16:07 ` [PATCH v4 4/7] media: v4l2-subdev: add stubs for v4l2_subdev_get_try_* Marco Felsch
2019-03-21 10:01 ` Jacopo Mondi
2019-03-21 10:59 ` Marco Felsch
2019-01-29 16:07 ` [PATCH v4 5/7] media: tvp5150: add FORMAT_TRY support for get/set selection handlers Marco Felsch
2019-01-29 16:07 ` [PATCH v4 6/7] media: tvp5150: initialize subdev before parsing device tree Marco Felsch
2019-01-29 16:07 ` [PATCH v4 7/7] media: tvp5150: add s_power callback Marco Felsch
2019-02-12 16:09 ` [PATCH v4 0/7] TVP5150 new features Marco Felsch
2019-03-05 9:46 ` Marco Felsch
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190129160757.2314-4-m.felsch@pengutronix.de \
--to=m.felsch@pengutronix.de \
--cc=afshin.nasser@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=javierm@redhat.com \
--cc=kernel@pengutronix.de \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mchehab@kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=robh+dt@kernel.org \
--cc=robh@kernel.org \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).