Re: [PATCH v6 06/13] media: dt-bindings: tvp5150: Add input port connectors DT bindings

[Mauro Carvalho Chehab <mchehab@kernel.org>]

Em Mon, 15 Apr 2019 14:44:06 +0200
Marco Felsch <m.felsch@pengutronix.de> escreveu:

> The TVP5150/1 decoders support different video input sources to their
> AIP1A/B pins.
> 
> Possible configurations are as follows:
>   - Analog Composite signal connected to AIP1A.
>   - Analog Composite signal connected to AIP1B.
>   - Analog S-Video Y (luminance) and C (chrominance)
>     signals connected to AIP1A and AIP1B respectively.
> 
> This patch extends the device tree bindings documentation to describe
> how the input connectors for these devices should be defined in a DT.
> 
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> Reviewed-by: Rob Herring <robh@kernel.org>

Looks good to me.

> ---
> Changelog:
> 
> v3:
> - remove examples for one and two inputs
> - replace space by tabs
> 
> v2:
> - adapt port layout in accordance with
>   https://www.spinics.net/lists/linux-media/msg138546.html with the
>   svideo-connector deviation (use only one endpoint)
> 
>  .../devicetree/bindings/media/i2c/tvp5150.txt | 92 +++++++++++++++++--
>  1 file changed, 85 insertions(+), 7 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> index 8c0fc1a26bf0..bdd273d8b44d 100644
> --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
> @@ -12,11 +12,31 @@ Optional Properties:
>  - pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
>  - reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
>  
> -The device node must contain one 'port' child node for its digital output
> -video port, in accordance with the video interface bindings defined in
> -Documentation/devicetree/bindings/media/video-interfaces.txt.
> +The device node must contain one 'port' child node per device physical input
> +and output port, in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
> +are numbered as follows
>  
> -Required Endpoint Properties for parallel synchronization:
> +	  Name		Type		Port
> +	--------------------------------------
> +	  AIP1A		sink		0
> +	  AIP1B		sink		1
> +	  Y-OUT		src		2
> +
> +The device node must contain at least one sink port and the src port. Each input
> +port must be linked to an endpoint defined in
> +Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. The
> +port/connector layout is as follows
> +
> +tvp-5150 port@0 (AIP1A)
> +	endpoint@0 -----------> Comp0-Con  port
> +	endpoint@1 -----------> Svideo-Con port
> +tvp-5150 port@1 (AIP1B)
> +	endpoint   -----------> Comp1-Con  port
> +tvp-5150 port@2
> +	endpoint (video bitstream output at YOUT[0-7] parallel bus)
> +
> +Required Endpoint Properties for parallel synchronization on output port:
>  
>  - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
>  - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
> @@ -26,17 +46,75 @@ Required Endpoint Properties for parallel synchronization:
>  If none of hsync-active, vsync-active and field-even-active is specified,
>  the endpoint is assumed to use embedded BT.656 synchronization.
>  
> -Example:
> +Example - three input sources:
> +
> +comp_connector_0 {
> +	compatible = "composite-video-connector";
> +	label = "Composite0";
> +
> +	port {
> +		composite0_to_tvp5150: endpoint {
> +			remote-endpoint = <&tvp5150_to_composite0>;
> +		};
> +	};
> +};
> +
> +comp_connector_1 {
> +	compatible = "composite-video-connector";
> +	label = "Composite1";
> +
> +	port {
> +		composite1_to_tvp5150: endpoint {
> +			remote-endpoint = <&tvp5150_to_composite1>;
> +		};
> +	};
> +};
> +
> +svid_connector {
> +	compatible = "svideo-connector";
> +	label = "S-Video";
> +
> +	port {
> +		svideo_to_tvp5150: endpoint {
> +			remote-endpoint = <&tvp5150_to_svideo>;
> +		};
> +	};
> +};
>  
>  &i2c2 {
> -	...
>  	tvp5150@5c {
>  		compatible = "ti,tvp5150";
>  		reg = <0x5c>;
>  		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
>  		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
>  
> -		port {
> +		port@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +
> +			tvp5150_to_composite0: endpoint@0 {
> +				reg = <0>;
> +				remote-endpoint = <&composite0_to_tvp5150>;
> +			};
> +
> +			tvp5150_to_svideo: endpoint@1 {
> +				reg = <1>;
> +				remote-endpoint = <&svideo_to_tvp5150>;
> +			};
> +		};
> +
> +		port@1 {
> +			reg = <1>;
> +
> +			tvp5150_to_composite1: endpoint {
> +                                remote-endpoint = <&composite1_to_tvp5150>;
> +			};
> +		};
> +
> +		port@2 {
> +			reg = <2>;
> +
>  			tvp5150_1: endpoint {
>  				remote-endpoint = <&ccdc_ep>;
>  			};



Thanks,
Mauro