From: Sean Young <sean@mess.org>
To: linux-media@vger.kernel.org
Subject: [PATCH 2/2] media: dvb: remove replace frontend_debug with dynamic debug
Date: Mon, 20 May 2019 21:01:44 +0100 [thread overview]
Message-ID: <20190520200144.16713-2-sean@mess.org> (raw)
In-Reply-To: <20190520200144.16713-1-sean@mess.org>
This simplifies the code a little. This does move a dev_dbg() into a
timing sensitive code path. This is in the microseconds order so dev_dbg()
should not make a difference.
Signed-off-by: Sean Young <sean@mess.org>
---
drivers/media/dvb-core/dvb_frontend.c | 39 +++++++++++++--------------
1 file changed, 18 insertions(+), 21 deletions(-)
diff --git a/drivers/media/dvb-core/dvb_frontend.c b/drivers/media/dvb-core/dvb_frontend.c
index d3c0f6267bf8..3aad13415654 100644
--- a/drivers/media/dvb-core/dvb_frontend.c
+++ b/drivers/media/dvb-core/dvb_frontend.c
@@ -47,15 +47,12 @@
#include <media/dvbdev.h>
#include <linux/dvb/version.h>
-static int dvb_frontend_debug;
static int dvb_shutdown_timeout;
static int dvb_force_auto_inversion;
static int dvb_override_tune_delay;
static int dvb_powerdown_on_sleep = 1;
static int dvb_mfe_wait_time = 5;
-module_param_named(frontend_debug, dvb_frontend_debug, int, 0644);
-MODULE_PARM_DESC(frontend_debug, "Turn on/off frontend core debugging (default:off).");
module_param(dvb_shutdown_timeout, int, 0644);
MODULE_PARM_DESC(dvb_shutdown_timeout, "wait <shutdown_timeout> seconds after close() before suspending hardware");
module_param(dvb_force_auto_inversion, int, 0644);
@@ -917,9 +914,9 @@ static void dvb_frontend_get_frequency_limits(struct dvb_frontend *fe,
"DVB: adapter %i frontend %u frequency limits undefined - fix the driver\n",
fe->dvb->num, fe->id);
- if (dvb_frontend_debug)
- dprintk("frequency interval: tuner: %u...%u, frontend: %u...%u",
- tuner_min, tuner_max, frontend_min, frontend_max);
+ dev_dbg(fe->dvb->device,
+ "frequency interval: tuner: %u...%u, frontend: %u...%u",
+ tuner_min, tuner_max, frontend_min, frontend_max);
/* If the standard is for satellite, convert frequencies to kHz */
switch (c->delivery_system) {
@@ -2586,41 +2583,41 @@ static int dvb_frontend_handle_ioctl(struct file *file,
*/
unsigned long swcmd = ((unsigned long)parg) << 1;
ktime_t nexttime;
- ktime_t tv[10];
+ ktime_t now, lasttime;
int i;
u8 last = 1;
- if (dvb_frontend_debug)
- dprintk("switch command: 0x%04lx\n",
- swcmd);
+ dev_dbg(fe->dvb->device, "switch command: 0x%04lx\n",
+ swcmd);
nexttime = ktime_get_boottime();
- if (dvb_frontend_debug)
- tv[0] = nexttime;
/* before sending a command, initialize by sending
* a 32ms 18V to the switch
*/
fe->ops.set_voltage(fe, SEC_VOLTAGE_18);
+
+ dev_dbg(fe->dvb->device, "(adapter %d): switch delay (should be 32k followed by all 8k)\n",
+ fe->dvb->num);
+
+ lasttime = nexttime;
dvb_frontend_sleep_until(&nexttime, 32000);
for (i = 0; i < 9; i++) {
- if (dvb_frontend_debug)
- tv[i + 1] = ktime_get_boottime();
if ((swcmd & 0x01) != last) {
/* set voltage to (last ? 13V : 18V) */
fe->ops.set_voltage(fe, (last) ? SEC_VOLTAGE_13 : SEC_VOLTAGE_18);
last = (last) ? 0 : 1;
}
swcmd = swcmd >> 1;
+
+ now = ktime_get_boottime();
+ dev_dbg(fe->dvb->device, "%d: %lld\n", i,
+ ktime_us_delta(now, lasttime));
+ lasttime = now;
+
if (i != 8)
dvb_frontend_sleep_until(&nexttime, 8000);
}
- if (dvb_frontend_debug) {
- dprintk("(adapter %d): switch delay (should be 32k followed by all 8k)\n",
- fe->dvb->num);
- for (i = 1; i < 10; i++)
- pr_info("%d: %d\n", i,
- (int)ktime_us_delta(tv[i], tv[i - 1]));
- }
+
err = 0;
fepriv->state = FESTATE_DISEQC;
fepriv->status = 0;
--
2.20.1
next prev parent reply other threads:[~2019-05-20 20:01 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-20 20:01 [PATCH 1/2] media: dvb: warning about dvb frequency limits produces too much noise Sean Young
2019-05-20 20:01 ` Sean Young [this message]
2019-05-20 20:32 ` [PATCH 2/2] media: dvb: remove replace frontend_debug with dynamic debug Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190520200144.16713-2-sean@mess.org \
--to=sean@mess.org \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).