From: Hans Verkuil <hverkuil-cisco@xs4all.nl>
To: linux-media@vger.kernel.org
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Subject: [PATCHv2 5/7] cec: support CEC_MSG_FL_RAW
Date: Wed, 22 May 2019 11:55:48 +0200 [thread overview]
Message-ID: <20190522095550.22026-6-hverkuil-cisco@xs4all.nl> (raw)
In-Reply-To: <20190522095550.22026-1-hverkuil-cisco@xs4all.nl>
If this flag is set, then check for root permissions and skip
all message checks expect for the core checks (i.e. validate the
length etc.).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
---
drivers/media/cec/cec-adap.c | 107 ++++++++++++++++++++---------------
1 file changed, 62 insertions(+), 45 deletions(-)
diff --git a/drivers/media/cec/cec-adap.c b/drivers/media/cec/cec-adap.c
index 5b9232b6e663..9a1ec9299aca 100644
--- a/drivers/media/cec/cec-adap.c
+++ b/drivers/media/cec/cec-adap.c
@@ -720,6 +720,7 @@ int cec_transmit_msg_fh(struct cec_adapter *adap, struct cec_msg *msg,
struct cec_fh *fh, bool block)
{
struct cec_data *data;
+ bool is_raw = msg_is_raw(msg);
msg->rx_ts = 0;
msg->tx_ts = 0;
@@ -735,10 +736,10 @@ int cec_transmit_msg_fh(struct cec_adapter *adap, struct cec_msg *msg,
/* Make sure the timeout isn't 0. */
msg->timeout = 1000;
}
- if (msg->timeout)
- msg->flags &= CEC_MSG_FL_REPLY_TO_FOLLOWERS;
- else
- msg->flags = 0;
+ msg->flags &= CEC_MSG_FL_REPLY_TO_FOLLOWERS | CEC_MSG_FL_RAW;
+
+ if (!msg->timeout)
+ msg->flags &= ~CEC_MSG_FL_REPLY_TO_FOLLOWERS;
/* Sanity checks */
if (msg->len == 0 || msg->len > CEC_MAX_MSG_SIZE) {
@@ -761,54 +762,70 @@ int cec_transmit_msg_fh(struct cec_adapter *adap, struct cec_msg *msg,
return -EINVAL;
}
- /* A CDC-Only device can only send CDC messages */
- if ((adap->log_addrs.flags & CEC_LOG_ADDRS_FL_CDC_ONLY) &&
- (msg->len == 1 || msg->msg[1] != CEC_MSG_CDC_MESSAGE))
- return -EINVAL;
+ if (is_raw) {
+ if (!capable(CAP_SYS_RAWIO))
+ return -EPERM;
+ } else {
+ /* A CDC-Only device can only send CDC messages */
+ if ((adap->log_addrs.flags & CEC_LOG_ADDRS_FL_CDC_ONLY) &&
+ (msg->len == 1 || msg->msg[1] != CEC_MSG_CDC_MESSAGE)) {
+ dprintk(1, "%s: not a CDC message\n", __func__);
+ return -EINVAL;
+ }
- if (msg->len >= 4 && msg->msg[1] == CEC_MSG_CDC_MESSAGE) {
- msg->msg[2] = adap->phys_addr >> 8;
- msg->msg[3] = adap->phys_addr & 0xff;
- }
+ if (msg->len >= 4 && msg->msg[1] == CEC_MSG_CDC_MESSAGE) {
+ msg->msg[2] = adap->phys_addr >> 8;
+ msg->msg[3] = adap->phys_addr & 0xff;
+ }
- if (msg->len == 1) {
- if (cec_msg_destination(msg) == 0xf) {
- dprintk(1, "%s: invalid poll message\n", __func__);
+ if (msg->len == 1) {
+ if (cec_msg_destination(msg) == 0xf) {
+ dprintk(1, "%s: invalid poll message\n",
+ __func__);
+ return -EINVAL;
+ }
+ if (cec_has_log_addr(adap, cec_msg_destination(msg))) {
+ /*
+ * If the destination is a logical address our
+ * adapter has already claimed, then just NACK
+ * this. It depends on the hardware what it will
+ * do with a POLL to itself (some OK this), so
+ * it is just as easy to handle it here so the
+ * behavior will be consistent.
+ */
+ msg->tx_ts = ktime_get_ns();
+ msg->tx_status = CEC_TX_STATUS_NACK |
+ CEC_TX_STATUS_MAX_RETRIES;
+ msg->tx_nack_cnt = 1;
+ msg->sequence = ++adap->sequence;
+ if (!msg->sequence)
+ msg->sequence = ++adap->sequence;
+ return 0;
+ }
+ }
+ if (msg->len > 1 && !cec_msg_is_broadcast(msg) &&
+ cec_has_log_addr(adap, cec_msg_destination(msg))) {
+ dprintk(1, "%s: destination is the adapter itself\n",
+ __func__);
return -EINVAL;
}
- if (cec_has_log_addr(adap, cec_msg_destination(msg))) {
- /*
- * If the destination is a logical address our adapter
- * has already claimed, then just NACK this.
- * It depends on the hardware what it will do with a
- * POLL to itself (some OK this), so it is just as
- * easy to handle it here so the behavior will be
- * consistent.
- */
- msg->tx_ts = ktime_get_ns();
- msg->tx_status = CEC_TX_STATUS_NACK |
- CEC_TX_STATUS_MAX_RETRIES;
- msg->tx_nack_cnt = 1;
- msg->sequence = ++adap->sequence;
- if (!msg->sequence)
- msg->sequence = ++adap->sequence;
- return 0;
+ if (msg->len > 1 && adap->is_configured &&
+ !cec_has_log_addr(adap, cec_msg_initiator(msg))) {
+ dprintk(1, "%s: initiator has unknown logical address %d\n",
+ __func__, cec_msg_initiator(msg));
+ return -EINVAL;
+ }
+ if (!adap->is_configured && !adap->is_configuring &&
+ msg->msg[0] != 0xf0) {
+ dprintk(1, "%s: adapter is unconfigured\n", __func__);
+ return -ENONET;
}
}
- if (msg->len > 1 && !cec_msg_is_broadcast(msg) &&
- cec_has_log_addr(adap, cec_msg_destination(msg))) {
- dprintk(1, "%s: destination is the adapter itself\n", __func__);
- return -EINVAL;
- }
- if (msg->len > 1 && adap->is_configured &&
- !cec_has_log_addr(adap, cec_msg_initiator(msg))) {
- dprintk(1, "%s: initiator has unknown logical address %d\n",
- __func__, cec_msg_initiator(msg));
- return -EINVAL;
- }
+
if (!adap->is_configured && !adap->is_configuring) {
- if (adap->needs_hpd || msg->msg[0] != 0xf0) {
- dprintk(1, "%s: adapter is unconfigured\n", __func__);
+ if (adap->needs_hpd) {
+ dprintk(1, "%s: adapter is unconfigured and needs HPD\n",
+ __func__);
return -ENONET;
}
if (msg->reply) {
--
2.20.1
next prev parent reply other threads:[~2019-05-22 9:56 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-22 9:55 [PATCHv2 0/7] cec: various improvements Hans Verkuil
2019-05-22 9:55 ` [PATCHv2 1/7] cec: cec_transmit_msg_fh: do sanity checks first Hans Verkuil
2019-05-22 9:55 ` [PATCHv2 2/7] cec: move check from cec_transmit to cec_transmit_msg_fh Hans Verkuil
2019-05-22 9:55 ` [PATCHv2 3/7] cec: add CEC_MSG_FL_RAW flag and msg_is_raw helper function Hans Verkuil
2019-05-22 9:55 ` [PATCHv2 4/7] cec-ioc-receive.rst: document CEC_MSG_FL_RAW Hans Verkuil
2019-05-22 9:55 ` Hans Verkuil [this message]
2019-05-22 9:55 ` [PATCHv2 6/7] cec: allow any initiator for Ping and Image/Text View On Hans Verkuil
2019-05-22 9:55 ` [PATCHv2 7/7] cec-ioc-g-mode.rst: be more specific when EPERM is returned Hans Verkuil
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190522095550.22026-6-hverkuil-cisco@xs4all.nl \
--to=hverkuil-cisco@xs4all.nl \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).