* [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings
@ 2019-05-20 20:18 Marek Vasut
2019-05-20 20:18 ` [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x Marek Vasut
` (2 more replies)
0 siblings, 3 replies; 22+ messages in thread
From: Marek Vasut @ 2019-05-20 20:18 UTC (permalink / raw)
To: linux-media
Cc: Marek Vasut, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring,
devicetree
Add bindings for the Intersil ISL7998x BT656-to-MIPI-CSI2 decoder.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
To: linux-media@vger.kernel.org
---
.../bindings/media/i2c/isl7998x.txt | 37 +++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/isl7998x.txt
diff --git a/Documentation/devicetree/bindings/media/i2c/isl7998x.txt b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt
new file mode 100644
index 000000000000..c21703983360
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt
@@ -0,0 +1,37 @@
+Intersil ISL7998x BT656-to-MIPI-CSI2 decoder
+
+The Intersil ISL7998x is a BT656-to-MIPI-CSI decoder which, capable of
+receiving up to four analog stream and multiplexing them into up to four
+MIPI CSI2 virtual channels, using one MIPI clock lane and 1/2 data lanes.
+
+Required Properties:
+- compatible: value should be "isil,isl79987"
+- pd-gpios: a GPIO spec for the Power Down pin (active high)
+
+Option Properties:
+- isil,num-inputs: Number of connected inputs (1, 2 or 4)
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+ i2c_master {
+ isl7998x_mipi@44 {
+ compatible = "isil,isl79987";
+ reg = <0x44>;
+ isil,num-inputs = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_videoadc>;
+ pd-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ port {
+ isl79987_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
--
2.20.1
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x 2019-05-20 20:18 [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Marek Vasut @ 2019-05-20 20:18 ` Marek Vasut 2019-07-01 7:58 ` Jacopo Mondi ` (2 more replies) 2019-05-28 11:47 ` [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Jacopo Mondi 2019-07-01 8:04 ` Sakari Ailus 2 siblings, 3 replies; 22+ messages in thread From: Marek Vasut @ 2019-05-20 20:18 UTC (permalink / raw) To: linux-media; +Cc: Marek Vasut, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring Add driver for the Intersil ISL7998x BT656-to-MIPI-CSI2 video decoder. This chip supports 1/2/4 analog video inputs and converts them into 1/2/4 VCs in MIPI CSI2 stream. This driver currently supports ISL79987 and both 720x480 and 720x576 resolutions, however as per specification, all inputs must use the same resolution and standard. The only supported pixel format is now YUYV/YUV422. The chip should support RGB565 on the CSI2 as well, but this is currently unsupported. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Cc: Rob Herring <robh+dt@kernel.org> To: linux-media@vger.kernel.org --- drivers/media/i2c/Kconfig | 6 + drivers/media/i2c/Makefile | 1 + drivers/media/i2c/isl7998x.c | 1111 ++++++++++++++++++++++++++++++++++ 3 files changed, 1118 insertions(+) create mode 100644 drivers/media/i2c/isl7998x.c diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig index 7793358ab8b3..af2ea08d6c59 100644 --- a/drivers/media/i2c/Kconfig +++ b/drivers/media/i2c/Kconfig @@ -929,6 +929,12 @@ config VIDEO_NOON010PC30 help This driver supports NOON010PC30 CIF camera from Siliconfile +config VIDEO_ISL7998X + tristate "Intersil ISL7998x support" + depends on I2C && VIDEO_V4L2 + help + This driver supports Intersil ISL7998x BT656-to-MIPI-CSI2 bridge. + source "drivers/media/i2c/m5mols/Kconfig" config VIDEO_RJ54N1 diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile index d8ad9dad495d..a66f105a7bcc 100644 --- a/drivers/media/i2c/Makefile +++ b/drivers/media/i2c/Makefile @@ -113,6 +113,7 @@ obj-$(CONFIG_VIDEO_IMX258) += imx258.o obj-$(CONFIG_VIDEO_IMX274) += imx274.o obj-$(CONFIG_VIDEO_IMX319) += imx319.o obj-$(CONFIG_VIDEO_IMX355) += imx355.o +obj-$(CONFIG_VIDEO_ISL7998X) += isl7998x.o obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o obj-$(CONFIG_SDR_MAX2175) += max2175.o diff --git a/drivers/media/i2c/isl7998x.c b/drivers/media/i2c/isl7998x.c new file mode 100644 index 000000000000..858e98d8b494 --- /dev/null +++ b/drivers/media/i2c/isl7998x.c @@ -0,0 +1,1111 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Intersil ISL7998x BT656-to-MIPI-CSI2 driver + * + * Copyright (C) 2018-2019 Marek Vasut <marex@denx.de> + */ +#include <linux/videodev2.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/i2c.h> +#include <linux/log2.h> +#include <linux/module.h> +#include <linux/of_graph.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <linux/v4l2-mediabus.h> +#include <media/v4l2-async.h> +#include <media/v4l2-clk.h> +#include <media/v4l2-common.h> +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> +#include <media/v4l2-fwnode.h> + +#define ISL7998x_WIDTH 720 +#define ISL7998x_HEIGHT 480 +#define ISL7998x_INPUTS 4 + +#define V4L2_CID_TEST_PATTERN_COLOR (V4L2_CID_USER_BASE | 0x1001) +#define V4L2_CID_TEST_PATTERN_CHANNELS (V4L2_CID_USER_BASE | 0x1002) +#define V4L2_CID_TEST_PATTERN_BARS (V4L2_CID_USER_BASE | 0x1003) + +#define ISL7998x_REG(page, reg) (((page) << 8) | (reg)) + +#define ISL7998x_REG_Pn_SIZE 256 +#define ISL7998x_REG_Pn_BASE(n) ((n) * ISL7998x_REG_Pn_SIZE) + +#define ISL7998x_REG_Px_DEC_PAGE(page) ISL7998x_REG((page), 0xff) +#define ISL7998x_REG_Px_DEC_PAGE_MASK 0xf +#define ISL7998x_REG_P0_PRODUCT_ID_CODE ISL7998x_REG(0, 0x00) +#define ISL7998x_REG_P0_PRODUCT_REV_CODE ISL7998x_REG(0, 0x01) +#define ISL7998x_REG_P0_SW_RESET_CTL ISL7998x_REG(0, 0x02) +#define ISL7998x_REG_P0_IO_BUFFER_CTL ISL7998x_REG(0, 0x03) +#define ISL7998x_REG_P0_IO_BUFFER_CTL_1_1 ISL7998x_REG(0, 0x04) +#define ISL7998x_REG_P0_IO_PAD_PULL_EN_CTL ISL7998x_REG(0, 0x05) +#define ISL7998x_REG_P0_IO_BUFFER_CTL_1_2 ISL7998x_REG(0, 0x06) +#define ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL ISL7998x_REG(0, 0x07) +#define ISL7998x_REG_P0_CLK_CTL_1 ISL7998x_REG(0, 0x08) +#define ISL7998x_REG_P0_CLK_CTL_2 ISL7998x_REG(0, 0x09) +#define ISL7998x_REG_P0_CLK_CTL_3 ISL7998x_REG(0, 0x0a) +#define ISL7998x_REG_P0_CLK_CTL_4 ISL7998x_REG(0, 0x0b) +#define ISL7998x_REG_P0_MPP1_SYNC_CTL ISL7998x_REG(0, 0x0c) +#define ISL7998x_REG_P0_MPP2_SYNC_CTL ISL7998x_REG(0, 0x0d) +#define ISL7998x_REG_P0_IRQ_SYNC_CTL ISL7998x_REG(0, 0x0e) +#define ISL7998x_REG_P0_INTERRUPT_STATUS ISL7998x_REG(0, 0x10) +#define ISL7998x_REG_P0_CHAN_1_IRQ ISL7998x_REG(0, 0x11) +#define ISL7998x_REG_P0_CHAN_2_IRQ ISL7998x_REG(0, 0x12) +#define ISL7998x_REG_P0_CHAN_3_IRQ ISL7998x_REG(0, 0x13) +#define ISL7998x_REG_P0_CHAN_4_IRQ ISL7998x_REG(0, 0x14) +#define ISL7998x_REG_P0_SHORT_DIAG_IRQ ISL7998x_REG(0, 0x15) +#define ISL7998x_REG_P0_CHAN_1_IRQ_EN ISL7998x_REG(0, 0x16) +#define ISL7998x_REG_P0_CHAN_2_IRQ_EN ISL7998x_REG(0, 0x17) +#define ISL7998x_REG_P0_CHAN_3_IRQ_EN ISL7998x_REG(0, 0x18) +#define ISL7998x_REG_P0_CHAN_4_IRQ_EN ISL7998x_REG(0, 0x19) +#define ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN ISL7998x_REG(0, 0x1a) +#define ISL7998x_REG_P0_CHAN_1_STATUS ISL7998x_REG(0, 0x1b) +#define ISL7998x_REG_P0_CHAN_2_STATUS ISL7998x_REG(0, 0x1c) +#define ISL7998x_REG_P0_CHAN_3_STATUS ISL7998x_REG(0, 0x1d) +#define ISL7998x_REG_P0_CHAN_4_STATUS ISL7998x_REG(0, 0x1e) +#define ISL7998x_REG_P0_SHORT_DIAG_STATUS ISL7998x_REG(0, 0x1f) +#define ISL7998x_REG_P0_CLOCK_DELAY ISL7998x_REG(0, 0x20) + +#define ISL7998x_REG_Px_DEC_INPUT_FMT(pg) ISL7998x_REG((pg), 0x02) +#define ISL7998x_REG_Px_DEC_STATUS_1(pg) ISL7998x_REG((pg), 0x03) +#define ISL7998x_REG_Px_DEC_HS_DELAY_CTL(pg) ISL7998x_REG((pg), 0x04) +#define ISL7998x_REG_Px_DEC_ANCTL(pg) ISL7998x_REG((pg), 0x06) +#define ISL7998x_REG_Px_DEC_CROP_HI(pg) ISL7998x_REG((pg), 0x07) +#define ISL7998x_REG_Px_DEC_VDELAY_LO(pg) ISL7998x_REG((pg), 0x08) +#define ISL7998x_REG_Px_DEC_VACTIVE_LO(pg) ISL7998x_REG((pg), 0x09) +#define ISL7998x_REG_Px_DEC_HDELAY_LO(pg) ISL7998x_REG((pg), 0x0a) +#define ISL7998x_REG_Px_DEC_HACTIVE_LO(pg) ISL7998x_REG((pg), 0x0b) +#define ISL7998x_REG_Px_DEC_CNTRL1(pg) ISL7998x_REG((pg), 0x0c) +#define ISL7998x_REG_Px_DEC_CSC_CTL(pg) ISL7998x_REG((pg), 0x0d) +#define ISL7998x_REG_Px_DEC_BRIGHT(pg) ISL7998x_REG((pg), 0x10) +#define ISL7998x_REG_Px_DEC_CONTRAST(pg) ISL7998x_REG((pg), 0x11) +#define ISL7998x_REG_Px_DEC_SHARPNESS(pg) ISL7998x_REG((pg), 0x12) +#define ISL7998x_REG_Px_DEC_SAT_U(pg) ISL7998x_REG((pg), 0x13) +#define ISL7998x_REG_Px_DEC_SAT_V(pg) ISL7998x_REG((pg), 0x14) +#define ISL7998x_REG_Px_DEC_HUE(pg) ISL7998x_REG((pg), 0x15) +#define ISL7998x_REG_Px_DEC_VERT_PEAK(pg) ISL7998x_REG((pg), 0x17) +#define ISL7998x_REG_Px_DEC_CORING(pg) ISL7998x_REG((pg), 0x18) +#define ISL7998x_REG_Px_DEC_SDT(pg) ISL7998x_REG((pg), 0x1c) +#define ISL7998x_REG_Px_DEC_SDT_DET BIT(7) +#define ISL7998x_REG_Px_DEC_SDTR(pg) ISL7998x_REG((pg), 0x1d) +#define ISL7998x_REG_Px_DEC_CLMPG(pg) ISL7998x_REG((pg), 0x20) +#define ISL7998x_REG_Px_DEC_IAGC(pg) ISL7998x_REG((pg), 0x21) +#define ISL7998x_REG_Px_DEC_AGCGAIN(pg) ISL7998x_REG((pg), 0x22) +#define ISL7998x_REG_Px_DEC_PEAKWT(pg) ISL7998x_REG((pg), 0x23) +#define ISL7998x_REG_Px_DEC_CLMPL(pg) ISL7998x_REG((pg), 0x24) +#define ISL7998x_REG_Px_DEC_SYNCT(pg) ISL7998x_REG((pg), 0x25) +#define ISL7998x_REG_Px_DEC_MISSCNT(pg) ISL7998x_REG((pg), 0x26) +#define ISL7998x_REG_Px_DEC_PCLAMP(pg) ISL7998x_REG((pg), 0x27) +#define ISL7998x_REG_Px_DEC_VERT_CTL_1(pg) ISL7998x_REG((pg), 0x28) +#define ISL7998x_REG_Px_DEC_VERT_CTL_2(pg) ISL7998x_REG((pg), 0x29) +#define ISL7998x_REG_Px_DEC_CLR_KILL_LVL(pg) ISL7998x_REG((pg), 0x2a) +#define ISL7998x_REG_Px_DEC_COMB_FILTER_CTL(pg) ISL7998x_REG((pg), 0x2b) +#define ISL7998x_REG_Px_DEC_LUMA_DELAY(pg) ISL7998x_REG((pg), 0x2c) +#define ISL7998x_REG_Px_DEC_MISC1(pg) ISL7998x_REG((pg), 0x2d) +#define ISL7998x_REG_Px_DEC_MISC2(pg) ISL7998x_REG((pg), 0x2e) +#define ISL7998x_REG_Px_DEC_MISC3(pg) ISL7998x_REG((pg), 0x2f) +#define ISL7998x_REG_Px_DEC_MVSN(pg) ISL7998x_REG((pg), 0x30) +#define ISL7998x_REG_Px_DEC_CSTATUS2(pg) ISL7998x_REG((pg), 0x31) +#define ISL7998x_REG_Px_DEC_HFREF(pg) ISL7998x_REG((pg), 0x32) +#define ISL7998x_REG_Px_DEC_CLMD(pg) ISL7998x_REG((pg), 0x33) +#define ISL7998x_REG_Px_DEC_ID_DET_CTL(pg) ISL7998x_REG((pg), 0x34) +#define ISL7998x_REG_Px_DEC_CLCNTL(pg) ISL7998x_REG((pg), 0x35) +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_1(pg) ISL7998x_REG((pg), 0x36) +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_2(pg) ISL7998x_REG((pg), 0x37) +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_3(pg) ISL7998x_REG((pg), 0x38) +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_4(pg) ISL7998x_REG((pg), 0x39) +#define ISL7998x_REG_Px_DEC_SHORT_DET_CTL(pg) ISL7998x_REG((pg), 0x3a) +#define ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(pg) ISL7998x_REG((pg), 0x3b) +#define ISL7998x_REG_Px_DEC_AFE_TST_MUX_CTL(pg) ISL7998x_REG((pg), 0x3c) +#define ISL7998x_REG_Px_DEC_DATA_CONV(pg) ISL7998x_REG((pg), 0x3d) +#define ISL7998x_REG_Px_DEC_INTERNAL_TEST(pg) ISL7998x_REG((pg), 0x3f) +#define ISL7998x_REG_Px_DEC_H_DELAY_CTL(pg) ISL7998x_REG((pg), 0x43) +#define ISL7998x_REG_Px_DEC_H_DELAY_II_HI(pg) ISL7998x_REG((pg), 0x44) +#define ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(pg) ISL7998x_REG((pg), 0x45) + +#define ISL7998x_REG_Px_ACA_CTL_1(pg) ISL7998x_REG((pg), 0x80) +#define ISL7998x_REG_Px_ACA_GAIN_CTL(pg) ISL7998x_REG((pg), 0x81) +#define ISL7998x_REG_Px_ACA_Y_AVG_HI_LIMIT(pg) ISL7998x_REG((pg), 0x82) +#define ISL7998x_REG_Px_ACA_Y_AVG_LO_LIMIT(pg) ISL7998x_REG((pg), 0x83) +#define ISL7998x_REG_Px_ACA_Y_DET_THRESHOLD(pg) ISL7998x_REG((pg), 0x84) +#define ISL7998x_REG_Px_ACA_BLACK_LVL(pg) ISL7998x_REG((pg), 0x85) +#define ISL7998x_REG_Px_ACA_CENTER_LVL(pg) ISL7998x_REG((pg), 0x86) +#define ISL7998x_REG_Px_ACA_WHITE_LVL(pg) ISL7998x_REG((pg), 0x87) +#define ISL7998x_REG_Px_ACA_MEAN_OFF_LIMIT(pg) ISL7998x_REG((pg), 0x88) +#define ISL7998x_REG_Px_ACA_MEAN_OFF_UPGAIN(pg) ISL7998x_REG((pg), 0x89) +#define ISL7998x_REG_Px_ACA_MEAN_OFF_SLOPE(pg) ISL7998x_REG((pg), 0x8a) +#define ISL7998x_REG_Px_ACA_MEAN_OFF_DNGAIN(pg) ISL7998x_REG((pg), 0x8b) +#define ISL7998x_REG_Px_ACA_DELTA_CO_THRES(pg) ISL7998x_REG((pg), 0x8c) +#define ISL7998x_REG_Px_ACA_DELTA_SLOPE(pg) ISL7998x_REG((pg), 0x8d) +#define ISL7998x_REG_Px_ACA_LO_HI_AVG_THRES(pg) ISL7998x_REG((pg), 0x8e) +#define ISL7998x_REG_Px_ACA_LO_MAX_LVL_CTL(pg) ISL7998x_REG((pg), 0x8f) +#define ISL7998x_REG_Px_ACA_HI_MAX_LVL_CTL(pg) ISL7998x_REG((pg), 0x90) +#define ISL7998x_REG_Px_ACA_LO_UPGAIN_CTL(pg) ISL7998x_REG((pg), 0x91) +#define ISL7998x_REG_Px_ACA_LO_DNGAIN_CTL(pg) ISL7998x_REG((pg), 0x92) +#define ISL7998x_REG_Px_ACA_HI_UPGAIN_CTL(pg) ISL7998x_REG((pg), 0x93) +#define ISL7998x_REG_Px_ACA_HI_DNGAIN_CTL(pg) ISL7998x_REG((pg), 0x94) +#define ISL7998x_REG_Px_ACA_LOPASS_FLT_COEF(pg) ISL7998x_REG((pg), 0x95) +#define ISL7998x_REG_Px_ACA_PDF_INDEX(pg) ISL7998x_REG((pg), 0x96) +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_STT(pg) ISL7998x_REG((pg), 0x97) +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_SZ1(pg) ISL7998x_REG((pg), 0x98) +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_SZ2(pg) ISL7998x_REG((pg), 0x99) +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_STT(pg) ISL7998x_REG((pg), 0x9a) +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ1(pg) ISL7998x_REG((pg), 0x9b) +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(pg) ISL7998x_REG((pg), 0x9c) +#define ISL7998x_REG_Px_ACA_Y_AVG(pg) ISL7998x_REG((pg), 0xa0) +#define ISL7998x_REG_Px_ACA_Y_AVG_LIM(pg) ISL7998x_REG((pg), 0xa1) +#define ISL7998x_REG_Px_ACA_LO_AVG(pg) ISL7998x_REG((pg), 0xa2) +#define ISL7998x_REG_Px_ACA_HI_AVG(pg) ISL7998x_REG((pg), 0xa3) +#define ISL7998x_REG_Px_ACA_Y_MAX(pg) ISL7998x_REG((pg), 0xa4) +#define ISL7998x_REG_Px_ACA_Y_MIN(pg) ISL7998x_REG((pg), 0xa5) +#define ISL7998x_REG_Px_ACA_MOFFSET(pg) ISL7998x_REG((pg), 0xa6) +#define ISL7998x_REG_Px_ACA_LO_GAIN(pg) ISL7998x_REG((pg), 0xa7) +#define ISL7998x_REG_Px_ACA_HI_GAIN(pg) ISL7998x_REG((pg), 0xa8) +#define ISL7998x_REG_Px_ACA_LL_SLOPE(pg) ISL7998x_REG((pg), 0xa9) +#define ISL7998x_REG_Px_ACA_LH_SLOPE(pg) ISL7998x_REG((pg), 0xaa) +#define ISL7998x_REG_Px_ACA_HL_SLOPE(pg) ISL7998x_REG((pg), 0xab) +#define ISL7998x_REG_Px_ACA_HH_SLOPE(pg) ISL7998x_REG((pg), 0xac) +#define ISL7998x_REG_Px_ACA_X_LOW(pg) ISL7998x_REG((pg), 0xad) +#define ISL7998x_REG_Px_ACA_X_MEAN(pg) ISL7998x_REG((pg), 0xae) +#define ISL7998x_REG_Px_ACA_X_HIGH(pg) ISL7998x_REG((pg), 0xaf) +#define ISL7998x_REG_Px_ACA_Y_LOW(pg) ISL7998x_REG((pg), 0xb0) +#define ISL7998x_REG_Px_ACA_Y_MEAN(pg) ISL7998x_REG((pg), 0xb1) +#define ISL7998x_REG_Px_ACA_Y_HIGH(pg) ISL7998x_REG((pg), 0xb2) +#define ISL7998x_REG_Px_ACA_CTL_2(pg) ISL7998x_REG((pg), 0xb3) +#define ISL7998x_REG_Px_ACA_CTL_3(pg) ISL7998x_REG((pg), 0xb4) +#define ISL7998x_REG_Px_ACA_CTL_4(pg) ISL7998x_REG((pg), 0xb5) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(pg) ISL7998x_REG((pg), 0xc0) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TL_H(pg) ISL7998x_REG((pg), 0xc1) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TL_L(pg) ISL7998x_REG((pg), 0xc2) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TL_H(pg) ISL7998x_REG((pg), 0xc3) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TL_L(pg) ISL7998x_REG((pg), 0xc4) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TR_H(pg) ISL7998x_REG((pg), 0xc5) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TR_L(pg) ISL7998x_REG((pg), 0xc6) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TR_H(pg) ISL7998x_REG((pg), 0xc7) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TR_L(pg) ISL7998x_REG((pg), 0xc8) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BL_H(pg) ISL7998x_REG((pg), 0xc9) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BL_L(pg) ISL7998x_REG((pg), 0xca) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BL_H(pg) ISL7998x_REG((pg), 0xcb) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BL_L(pg) ISL7998x_REG((pg), 0xcc) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BR_H(pg) ISL7998x_REG((pg), 0xcd) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BR_L(pg) ISL7998x_REG((pg), 0xce) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BR_H(pg) ISL7998x_REG((pg), 0xcf) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BR_L(pg) ISL7998x_REG((pg), 0xd0) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_LM_H(pg) ISL7998x_REG((pg), 0xd1) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_LM_L(pg) ISL7998x_REG((pg), 0xd2) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_LM_H(pg) ISL7998x_REG((pg), 0xd3) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_LM_L(pg) ISL7998x_REG((pg), 0xd4) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TM_H(pg) ISL7998x_REG((pg), 0xd5) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TM_L(pg) ISL7998x_REG((pg), 0xd6) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TM_H(pg) ISL7998x_REG((pg), 0xd7) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TM_L(pg) ISL7998x_REG((pg), 0xd8) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BM_H(pg) ISL7998x_REG((pg), 0xd9) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BM_L(pg) ISL7998x_REG((pg), 0xda) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BM_H(pg) ISL7998x_REG((pg), 0xdb) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BM_L(pg) ISL7998x_REG((pg), 0xdc) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_RM_H(pg) ISL7998x_REG((pg), 0xdd) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_RM_L(pg) ISL7998x_REG((pg), 0xde) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_RM_H(pg) ISL7998x_REG((pg), 0xdf) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_RM_L(pg) ISL7998x_REG((pg), 0xe0) +#define ISL7998x_REG_Px_ACA_HIST_DATA_LO(pg) ISL7998x_REG((pg), 0xe1) +#define ISL7998x_REG_Px_ACA_HIST_DATA_MID(pg) ISL7998x_REG((pg), 0xe2) +#define ISL7998x_REG_Px_ACA_HIST_DATA_HI(pg) ISL7998x_REG((pg), 0xe3) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_CLR(pg) ISL7998x_REG((pg), 0xe4) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_CB_CLR(pg) ISL7998x_REG((pg), 0xe5) +#define ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(pg) ISL7998x_REG((pg), 0xe6) +#define ISL7998x_REG_Px_ACA_XFER_HIST_HOST(pg) ISL7998x_REG((pg), 0xe7) + +#define ISL7998x_REG_P5_LI_ENGINE_CTL ISL7998x_REG(5, 0x00) +#define ISL7998x_REG_P5_LI_ENGINE_LINE_CTL ISL7998x_REG(5, 0x01) +#define ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH ISL7998x_REG(5, 0x02) +#define ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL ISL7998x_REG(5, 0x03) +#define ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT ISL7998x_REG(5, 0x04) +#define ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL ISL7998x_REG(5, 0x05) +#define ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL ISL7998x_REG(5, 0x06) +#define ISL7998x_REG_P5_MIPI_READ_START_CTL ISL7998x_REG(5, 0x07) +#define ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL ISL7998x_REG(5, 0x08) +#define ISL7998x_REG_P5_ONE_FIELD_MODE_CTL ISL7998x_REG(5, 0x09) +#define ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR ISL7998x_REG(5, 0x0a) +#define ISL7998x_REG_P5_TP_GEN_BAR_PATTERN ISL7998x_REG(5, 0x0b) +#define ISL7998x_REG_P5_MIPI_PCNT_PSFRM ISL7998x_REG(5, 0x0c) +#define ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL ISL7998x_REG(5, 0x0d) +#define ISL7998x_REG_P5_MIPI_VBLANK_PSFRM ISL7998x_REG(5, 0x0e) +#define ISL7998x_REG_P5_LI_ENGINE_CTL_2 ISL7998x_REG(5, 0x0f) +#define ISL7998x_REG_P5_MIPI_WCNT_1 ISL7998x_REG(5, 0x10) +#define ISL7998x_REG_P5_MIPI_WCNT_2 ISL7998x_REG(5, 0x11) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1 ISL7998x_REG(5, 0x12) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2 ISL7998x_REG(5, 0x13) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3 ISL7998x_REG(5, 0x14) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4 ISL7998x_REG(5, 0x15) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5 ISL7998x_REG(5, 0x16) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6 ISL7998x_REG(5, 0x17) +#define ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1 ISL7998x_REG(5, 0x18) +#define ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD ISL7998x_REG(5, 0x19) +#define ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD ISL7998x_REG(5, 0x1a) +#define ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2 ISL7998x_REG(5, 0x1b) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7 ISL7998x_REG(5, 0x1c) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8 ISL7998x_REG(5, 0x1d) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9 ISL7998x_REG(5, 0x1e) +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_10 ISL7998x_REG(5, 0x1f) +#define ISL7998x_REG_P5_TP_GEN_MIPI ISL7998x_REG(5, 0x20) +#define ISL7998x_REG_P5_ESC_MODE_TIME_CTL ISL7998x_REG(5, 0x21) +#define ISL7998x_REG_P5_AUTO_TEST_ERR_DET ISL7998x_REG(5, 0x22) +#define ISL7998x_REG_P5_MIPI_TIMING ISL7998x_REG(5, 0x23) +#define ISL7998x_REG_P5_PIC_HEIGHT_HIGH ISL7998x_REG(5, 0x24) +#define ISL7998x_REG_P5_PIC_HEIGHT_LOW ISL7998x_REG(5, 0x25) +#define ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL ISL7998x_REG(5, 0x26) +#define ISL7998x_REG_P5_FIFO_THRSH_CNT_1 ISL7998x_REG(5, 0x28) +#define ISL7998x_REG_P5_FIFO_THRSH_CNT_2 ISL7998x_REG(5, 0x29) +#define ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1 ISL7998x_REG(5, 0x2a) +#define ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2 ISL7998x_REG(5, 0x2b) +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_1 ISL7998x_REG(5, 0x2c) +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_2 ISL7998x_REG(5, 0x2d) +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_3 ISL7998x_REG(5, 0x2e) +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_4 ISL7998x_REG(5, 0x2f) +#define ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1 ISL7998x_REG(5, 0x30) +#define ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2 ISL7998x_REG(5, 0x31) +#define ISL7998x_REG_P5_MIPI_ANA_CLK_CTL ISL7998x_REG(5, 0x32) +#define ISL7998x_REG_P5_PLL_ANA_STATUS ISL7998x_REG(5, 0x33) +#define ISL7998x_REG_P5_PLL_ANA_MISC_CTL ISL7998x_REG(5, 0x34) +#define ISL7998x_REG_P5_MIPI_ANA ISL7998x_REG(5, 0x35) +#define ISL7998x_REG_P5_PLL_ANA ISL7998x_REG(5, 0x36) +#define ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1 ISL7998x_REG(5, 0x38) +#define ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2 ISL7998x_REG(5, 0x39) +#define ISL7998x_REG_P5_H_LINE_CNT_1 ISL7998x_REG(5, 0x3a) +#define ISL7998x_REG_P5_H_LINE_CNT_2 ISL7998x_REG(5, 0x3b) +#define ISL7998x_REG_P5_HIST_LINE_CNT_1 ISL7998x_REG(5, 0x3c) +#define ISL7998x_REG_P5_HIST_LINE_CNT_2 ISL7998x_REG(5, 0x3d) + +static const struct reg_sequence isl7998x_init_seq_1[] = { + { ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN, 0xff }, + { ISL7998x_REG_Px_DEC_SDT(0x1), 0x07 }, + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x1), 0x03 }, + { ISL7998x_REG_Px_DEC_SDT(0x2), 0x07 }, + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x2), 0x03 }, + { ISL7998x_REG_Px_DEC_SDT(0x3), 0x07 }, + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x3), 0x03 }, + { ISL7998x_REG_Px_DEC_SDT(0x4), 0x07 }, + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x4), 0x03 }, + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x00 }, + { ISL7998x_REG_P0_SW_RESET_CTL, 0x1f, 10 }, + { ISL7998x_REG_P0_IO_BUFFER_CTL, 0x00 }, + { ISL7998x_REG_P0_MPP2_SYNC_CTL, 0xc9 }, + { ISL7998x_REG_P0_IRQ_SYNC_CTL, 0xc9 }, + { ISL7998x_REG_P0_CHAN_1_IRQ, 0x03 }, + { ISL7998x_REG_P0_CHAN_2_IRQ, 0x00 }, + { ISL7998x_REG_P0_CHAN_3_IRQ, 0x00 }, + { ISL7998x_REG_P0_CHAN_4_IRQ, 0x00 }, + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x02 }, + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, 0x85 }, + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, 0xa0 }, + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x18 }, + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x40 }, + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x40 }, + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, + { ISL7998x_REG_P5_TP_GEN_MIPI, 0x00 }, + { ISL7998x_REG_P5_ESC_MODE_TIME_CTL, 0x0c }, + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x00 }, + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x19 }, + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_1, 0x18 }, + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_2, 0xf1 }, + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_3, 0x00 }, + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_4, 0xf1 }, + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1, 0x00 }, + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2, 0x00 }, + { ISL7998x_REG_P5_MIPI_ANA_CLK_CTL, 0x00 }, + { ISL7998x_REG_P5_PLL_ANA_STATUS, 0xc0 }, + { ISL7998x_REG_P5_PLL_ANA_MISC_CTL, 0x18 }, + { ISL7998x_REG_P5_PLL_ANA, 0x00 }, + { ISL7998x_REG_P0_SW_RESET_CTL, 0x10, 10 }, + /* Page 0xf means write to all of pages 1,2,3,4 */ + { ISL7998x_REG_Px_DEC_VDELAY_LO(0xf), 0x14 }, + { ISL7998x_REG_Px_DEC_MISC3(0xf), 0xe6 }, + { ISL7998x_REG_Px_DEC_CLMD(0xf), 0x85 }, + { ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(0xf), 0x11 }, + { ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), 0x00 }, + { ISL7998x_REG_P0_CLK_CTL_1, 0x1f }, + { ISL7998x_REG_P0_CLK_CTL_2, 0x43 }, + { ISL7998x_REG_P0_CLK_CTL_3, 0x4f }, +}; + +static const struct reg_sequence isl7998x_init_seq_2[] = { + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x10 }, + { ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT, 0xe4 }, + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x00 }, + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x60 }, + { ISL7998x_REG_P5_MIPI_READ_START_CTL, 0x2b }, + { ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL, 0x02 }, + { ISL7998x_REG_P5_ONE_FIELD_MODE_CTL, 0x00 }, + { ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR, 0x62 }, + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, 0x02 }, + { ISL7998x_REG_P5_MIPI_PCNT_PSFRM, 0x36 }, + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0x00 }, + { ISL7998x_REG_P5_MIPI_VBLANK_PSFRM, 0x6c }, + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0x00 }, + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1, 0x77 }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2, 0x17 }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3, 0x08 }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4, 0x38 }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5, 0x14 }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6, 0xf6 }, + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1, 0x00 }, + { ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD, 0x17 }, + { ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD, 0x0a }, + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2, 0x71 }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7, 0x7a }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8, 0x0f }, + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9, 0x8c }, + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x08 }, + { ISL7998x_REG_P5_FIFO_THRSH_CNT_1, 0x01 }, + { ISL7998x_REG_P5_FIFO_THRSH_CNT_2, 0x0e }, + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x00 }, + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, 0x03 }, + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2, 0xc0 }, + { ISL7998x_REG_P5_H_LINE_CNT_1, 0x06 }, + { ISL7998x_REG_P5_H_LINE_CNT_2, 0xb3 }, + { ISL7998x_REG_P5_HIST_LINE_CNT_1, 0x00 }, + { ISL7998x_REG_P5_HIST_LINE_CNT_2, 0xf1 }, + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x00 }, + { ISL7998x_REG_P5_MIPI_ANA, 0x00 }, + /* + * Wait a bit after reset so that the chip can capture a frame + * and update internal line counters. + */ + { ISL7998x_REG_P0_SW_RESET_CTL, 0x00, 50 }, +}; + +struct isl7998x_datafmt { + u32 code; + enum v4l2_colorspace colorspace; +}; + +static const struct isl7998x_datafmt isl7998x_colour_fmts[] = { + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_SRGB }, +}; + +/* Menu items for LINK_FREQ V4L2 control */ +static const s64 link_freq_menu_items[] = { + 108000000, 216000000, 432000000 +}; + +/* Menu items for TEST_PATTERN V4L2 control */ +static const char * const isl7998x_test_pattern_menu[] = { + "Disabled", "Enabled-PAL (720x576)", "Enabled-NTSC (720x480)" +}; + +struct isl7998x { + struct v4l2_subdev subdev; + struct regmap *regmap; + struct gpio_desc *pd_gpio; + unsigned int nr_mipi_lanes; + u32 nr_inputs; + + unsigned int width; + unsigned int height; + const struct isl7998x_datafmt *fmt; +#ifdef CONFIG_MEDIA_CONTROLLER + struct media_pad pad; +#endif + + struct v4l2_ctrl_handler ctrl_handler; + struct mutex ctrl_mutex; + /* V4L2 Controls */ + struct v4l2_ctrl *link_freq; + u8 test_pattern_enabled; + u8 test_pattern_bars; + u8 test_pattern_chans; + u8 test_pattern_color; +}; + +static struct isl7998x *sd_to_isl7998x(struct v4l2_subdev *sd) +{ + return container_of(sd, struct isl7998x, subdev); +} + +static struct isl7998x *i2c_to_isl7998x(const struct i2c_client *client) +{ + return sd_to_isl7998x(i2c_get_clientdata(client)); +} + +static int isl7998x_init(struct isl7998x *isl7998x) +{ + const unsigned int lanes = isl7998x->nr_mipi_lanes; + const u32 isl7998x_video_in_chan_map[] = { 0x00, 0x11, 0x02, 0x02 }; + const struct reg_sequence isl7998x_init_seq_custom[] = { + { ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL, + isl7998x_video_in_chan_map[isl7998x->nr_inputs - 1] }, + { ISL7998x_REG_P0_CLK_CTL_4, (lanes == 1) ? 0x40 : 0x41 }, + { ISL7998x_REG_P5_LI_ENGINE_CTL, (lanes == 1) ? 0x01 : 0x02 }, + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, + 0x20 | ((isl7998x->width >> 7) & 0x1f) }, + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, + (isl7998x->width << 1) & 0xff }, + }; + struct regmap *regmap = isl7998x->regmap; + int ret; + + ret = regmap_register_patch(regmap, isl7998x_init_seq_1, + ARRAY_SIZE(isl7998x_init_seq_1)); + if (ret) + return ret; + + ret = regmap_register_patch(regmap, isl7998x_init_seq_custom, + ARRAY_SIZE(isl7998x_init_seq_custom)); + if (ret) + return ret; + + return regmap_register_patch(regmap, isl7998x_init_seq_2, + ARRAY_SIZE(isl7998x_init_seq_2)); +} + +static int isl7998x_g_mbus_config(struct v4l2_subdev *sd, + struct v4l2_mbus_config *cfg) +{ + struct isl7998x *isl7998x = sd_to_isl7998x(sd); + + cfg->type = V4L2_MBUS_CSI2_DPHY; + cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; + if (isl7998x->nr_mipi_lanes == 1) + cfg->flags |= V4L2_MBUS_CSI2_1_LANE; + else + cfg->flags |= V4L2_MBUS_CSI2_2_LANE; + + return 0; +} + +static int isl7998x_s_stream(struct v4l2_subdev *sd, int enable) +{ + struct isl7998x *isl7998x = sd_to_isl7998x(sd); + + return isl7998x_init(isl7998x); +} + +static int isl7998x_enum_mbus_code(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) +{ + if (code->pad || code->index >= ARRAY_SIZE(isl7998x_colour_fmts)) + return -EINVAL; + + code->code = isl7998x_colour_fmts[code->index].code; + return 0; +} + +static const unsigned int isl7998x_std_res[] = { + 480, 576, 576, 480, 480, 576, 480, 480 +}; + +static int isl7998x_update_std(struct isl7998x *isl7998x) +{ + unsigned int height[ISL7998x_INPUTS]; + u8 scanning = GENMASK(ISL7998x_INPUTS - 1, 0); + unsigned int i; + int ret; + u32 reg; + + while (true) { + for (i = 0; i < ISL7998x_INPUTS; i++) { + ret = regmap_read(isl7998x->regmap, + ISL7998x_REG_Px_DEC_SDT(i + 1), ®); + if (ret) + return ret; + + /* Detection is still in progress, restart. */ + if (reg & ISL7998x_REG_Px_DEC_SDT_DET) { + scanning = GENMASK(ISL7998x_INPUTS - 1, 0); + break; + } + + scanning &= ~BIT(i); + height[i] = isl7998x_std_res[(reg >> 4) & 0x7]; + } + + if (!scanning) + break; + + mdelay(1); + } + + /* + * According to Renesas FAE, all input cameras must have the + * same standard on this chip. + */ + for (i = 1; i < isl7998x->nr_inputs ; i++) + if (height[i - 1] != height[i]) + return -EINVAL; + + isl7998x->height = height[0]; + + return 0; +} + +static int isl7998x_get_fmt(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *format) +{ + struct isl7998x *isl7998x = sd_to_isl7998x(sd); + struct v4l2_mbus_framefmt *mf = &format->format; + + if (format->pad != 0) + return -EINVAL; + + if (isl7998x->test_pattern_enabled == 1) { + mf->width = 720; + mf->height = 576; + } else if (isl7998x->test_pattern_enabled == 2) { + mf->width = 720; + mf->height = 480; + } else { + mf->width = isl7998x->width; + mf->height = isl7998x->height; + } + + mf->code = isl7998x->fmt->code; + mf->field = V4L2_FIELD_INTERLACED; + mf->colorspace = 0; + + return 0; +} + +static int isl7998x_set_fmt(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *format) +{ + struct isl7998x *isl7998x = sd_to_isl7998x(sd); + struct v4l2_mbus_framefmt *mf = &format->format; + int ret; + + if (format->pad != 0) + return -EINVAL; + + if (format->format.width != 720 || + (format->format.height != 480 && format->format.height != 576)) + return -EINVAL; + + if (format->format.code != MEDIA_BUS_FMT_YUYV8_2X8) + return -EINVAL; + + mf->width = format->format.width; + mf->height = format->format.height; + mf->code = format->format.code; + mf->field = V4L2_FIELD_INTERLACED; + mf->colorspace = 0; + + if (format->which != V4L2_SUBDEV_FORMAT_TRY) { + ret = isl7998x_update_std(isl7998x); + if (ret) + return ret; + mf->width = isl7998x->width; + mf->height = isl7998x->height; + isl7998x->fmt = &isl7998x_colour_fmts[0]; + } + + return 0; +} + +static int isl7998x_set_test_pattern(struct isl7998x *isl7998x) +{ + const struct reg_sequence isl7998x_init_seq_tpg_off[] = { + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0 }, + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0 } + }; + const struct reg_sequence isl7998x_init_seq_tpg_on[] = { + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, + isl7998x->test_pattern_bars << 6 }, + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, + isl7998x->test_pattern_enabled == 1 ? BIT(2) : 0 }, + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, + (isl7998x->test_pattern_chans << 4) | + (isl7998x->test_pattern_color << 2) } + }; + struct regmap *regmap = isl7998x->regmap; + + if (isl7998x->test_pattern_enabled) { + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_on, + ARRAY_SIZE(isl7998x_init_seq_tpg_on)); + } else { + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_off, + ARRAY_SIZE(isl7998x_init_seq_tpg_off)); + } +} + +static int isl7998x_set_ctrl(struct v4l2_ctrl *ctrl) +{ + struct isl7998x *isl7998x = container_of(ctrl->handler, + struct isl7998x, ctrl_handler); + + switch (ctrl->id) { + case V4L2_CID_TEST_PATTERN_BARS: + isl7998x->test_pattern_bars = ctrl->val & 0x3; + return isl7998x_set_test_pattern(isl7998x); + case V4L2_CID_TEST_PATTERN_CHANNELS: + isl7998x->test_pattern_chans = ctrl->val & 0xf; + return isl7998x_set_test_pattern(isl7998x); + case V4L2_CID_TEST_PATTERN_COLOR: + isl7998x->test_pattern_color = ctrl->val & 0x3; + return isl7998x_set_test_pattern(isl7998x); + case V4L2_CID_TEST_PATTERN: + isl7998x->test_pattern_enabled = !!ctrl->val; + return isl7998x_set_test_pattern(isl7998x); + } + + return 0; +} + +static int isl7998x_get_ctrl(struct v4l2_ctrl *ctrl) +{ + struct isl7998x *isl7998x = container_of(ctrl->handler, + struct isl7998x, ctrl_handler); + + v4l2_info(&isl7998x->subdev, "ctrl(id:0x%x,val:0x%x) is not handled\n", + ctrl->id, ctrl->val); + + return 0; +} + +static const struct v4l2_subdev_video_ops isl7998x_subdev_video_ops = { + .g_mbus_config = isl7998x_g_mbus_config, + .s_stream = isl7998x_s_stream, +}; + +static const struct v4l2_subdev_pad_ops isl7998x_subdev_pad_ops = { + .enum_mbus_code = isl7998x_enum_mbus_code, + .get_fmt = isl7998x_get_fmt, + .set_fmt = isl7998x_set_fmt, +}; + +static const struct v4l2_subdev_ops isl7998x_subdev_ops = { + .video = &isl7998x_subdev_video_ops, + .pad = &isl7998x_subdev_pad_ops, +}; + +static const struct media_entity_operations isl7998x_entity_ops = { + .link_validate = v4l2_subdev_link_validate, +}; + +static const struct v4l2_ctrl_ops isl7998x_ctrl_ops = { + .s_ctrl = isl7998x_set_ctrl, + .g_volatile_ctrl = isl7998x_get_ctrl, +}; + +static const char * const isl7998x_test_pattern_bars[] = { + "bbbbwb", "bbbwwb", "bbwbwb", "bbwwwb" +}; + +static const char * const isl7998x_test_pattern_colors[] = { + "Yellow", "Blue", "Green", "Pink" +}; + +static const struct v4l2_ctrl_config isl7998x_ctrls[] = { + { + .ops = &isl7998x_ctrl_ops, + .id = V4L2_CID_TEST_PATTERN_BARS, + .type = V4L2_CTRL_TYPE_MENU, + .name = "Test Pattern Bars", + .max = ARRAY_SIZE(isl7998x_test_pattern_bars) - 1, + .def = 0, + .qmenu = isl7998x_test_pattern_bars, + }, { + .ops = &isl7998x_ctrl_ops, + .id = V4L2_CID_TEST_PATTERN_CHANNELS, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Test Pattern Channels", + .min = 0, + .max = 0xf, + .step = 1, + .def = 0, + .flags = 0, + }, { + .ops = &isl7998x_ctrl_ops, + .id = V4L2_CID_TEST_PATTERN_COLOR, + .type = V4L2_CTRL_TYPE_MENU, + .name = "Test Pattern Color", + .max = ARRAY_SIZE(isl7998x_test_pattern_colors) - 1, + .def = 0, + .qmenu = isl7998x_test_pattern_colors, + }, +}; + +#define ISL7998x_REG_DECODER_ACA_READABLE_RANGE(page) \ + /* Decoder range */ \ + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ + ISL7998x_REG_Px_DEC_HUE(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ + ISL7998x_REG_Px_DEC_CORING(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ + ISL7998x_REG_Px_DEC_SDTR(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ + /* ACA range */ \ + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ + ISL7998x_REG_Px_ACA_CTL_4(page)), \ + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ + ISL7998x_REG_Px_DEC_PAGE(page)) + +#define ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(page) \ + /* Decoder range */ \ + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ + ISL7998x_REG_Px_DEC_INPUT_FMT(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page), \ + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ + ISL7998x_REG_Px_DEC_HUE(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ + ISL7998x_REG_Px_DEC_CORING(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ + ISL7998x_REG_Px_DEC_SDTR(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ + ISL7998x_REG_Px_DEC_MISC3(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMD(page), \ + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ + /* ACA range */ \ + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_2(page), \ + ISL7998x_REG_Px_ACA_CTL_4(page)), \ + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ + ISL7998x_REG_Px_ACA_HIST_DATA_LO(page)), \ + regmap_reg_range(ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page), \ + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ + ISL7998x_REG_Px_DEC_PAGE(page)) + +#define ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(page) \ + /* Decoder range */ \ + regmap_reg_range(ISL7998x_REG_Px_DEC_STATUS_1(page), \ + ISL7998x_REG_Px_DEC_STATUS_1(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ + ISL7998x_REG_Px_DEC_SDT(page)), \ + regmap_reg_range(ISL7998x_REG_Px_DEC_MVSN(page), \ + ISL7998x_REG_Px_DEC_HFREF(page)), \ + /* ACA range */ \ + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ + ISL7998x_REG_Px_ACA_Y_HIGH(page)), \ + regmap_reg_range(ISL7998x_REG_Px_ACA_HIST_DATA_LO(page), \ + ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(page)) + +static const struct regmap_range isl7998x_readable_ranges[] = { + regmap_reg_range(ISL7998x_REG_P0_PRODUCT_ID_CODE, + ISL7998x_REG_P0_IRQ_SYNC_CTL), + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, + ISL7998x_REG_P0_CLOCK_DELAY), + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), + ISL7998x_REG_Px_DEC_PAGE(0)), + + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(1), + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(2), + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(3), + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(4), + + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, + ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL), + regmap_reg_range(ISL7998x_REG_P5_FIFO_THRSH_CNT_1, + ISL7998x_REG_P5_PLL_ANA), + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, + ISL7998x_REG_P5_HIST_LINE_CNT_2), + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), + ISL7998x_REG_Px_DEC_PAGE(5)), +}; + +static const struct regmap_range isl7998x_writeable_ranges[] = { + regmap_reg_range(ISL7998x_REG_P0_SW_RESET_CTL, + ISL7998x_REG_P0_IRQ_SYNC_CTL), + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_IRQ, + ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN), + regmap_reg_range(ISL7998x_REG_P0_CLOCK_DELAY, + ISL7998x_REG_P0_CLOCK_DELAY), + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), + ISL7998x_REG_Px_DEC_PAGE(0)), + + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(1), + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(2), + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(3), + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(4), + + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, + ISL7998x_REG_P5_ESC_MODE_TIME_CTL), + regmap_reg_range(ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, + ISL7998x_REG_P5_PLL_ANA), + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, + ISL7998x_REG_P5_HIST_LINE_CNT_2), + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), + ISL7998x_REG_Px_DEC_PAGE(5)), + + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(0xf), +}; + +static const struct regmap_range isl7998x_volatile_ranges[] = { + regmap_reg_range(ISL7998x_REG_P0_MPP1_SYNC_CTL, + ISL7998x_REG_P0_IRQ_SYNC_CTL), + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, + ISL7998x_REG_P0_INTERRUPT_STATUS), + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_STATUS, + ISL7998x_REG_P0_SHORT_DIAG_STATUS), + + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(1), + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(2), + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(3), + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(4), + + regmap_reg_range(ISL7998x_REG_P5_AUTO_TEST_ERR_DET, + ISL7998x_REG_P5_PIC_HEIGHT_LOW), +}; + +static const struct regmap_access_table isl7998x_readable_table = { + .yes_ranges = isl7998x_readable_ranges, + .n_yes_ranges = ARRAY_SIZE(isl7998x_readable_ranges), +}; + +static const struct regmap_access_table isl7998x_writeable_table = { + .yes_ranges = isl7998x_writeable_ranges, + .n_yes_ranges = ARRAY_SIZE(isl7998x_writeable_ranges), +}; + +static const struct regmap_access_table isl7998x_volatile_table = { + .yes_ranges = isl7998x_volatile_ranges, + .n_yes_ranges = ARRAY_SIZE(isl7998x_volatile_ranges), +}; + +static const struct regmap_range_cfg isl7998x_ranges[] = { + { + .range_min = ISL7998x_REG_Pn_BASE(0), + .range_max = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), + .selector_reg = ISL7998x_REG_Px_DEC_PAGE(0), + .selector_mask = ISL7998x_REG_Px_DEC_PAGE_MASK, + .window_start = 0, + .window_len = 256, + } +}; + +static const struct regmap_config isl7998x_regmap = { + .reg_bits = 8, + .val_bits = 8, + .max_register = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), + .ranges = isl7998x_ranges, + .num_ranges = ARRAY_SIZE(isl7998x_ranges), + .rd_table = &isl7998x_readable_table, + .wr_table = &isl7998x_writeable_table, + .volatile_table = &isl7998x_volatile_table, + .cache_type = REGCACHE_RBTREE, +}; + +static int isl7998x_probe(struct i2c_client *client, + const struct i2c_device_id *did) +{ + struct device *dev = &client->dev; + struct v4l2_fwnode_endpoint endpoint; + struct device_node *ep; + struct isl7998x *isl7998x; + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent); + u32 chip_id; + int i, ret; + + ret = i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA); + if (!ret) { + dev_warn(&adapter->dev, + "I2C-Adapter doesn't support I2C_FUNC_SMBUS_WORD\n"); + return -EIO; + } + + isl7998x = devm_kzalloc(dev, sizeof(*isl7998x), GFP_KERNEL); + if (!isl7998x) + return -ENOMEM; + + /* Default to all four inputs active unless specified otherwise. */ + ret = of_property_read_u32(dev->of_node, "isil,num-inputs", + &isl7998x->nr_inputs); + if (ret) + isl7998x->nr_inputs = 4; + + if (isl7998x->nr_inputs != 1 && isl7998x->nr_inputs != 2 && + isl7998x->nr_inputs != 4) { + dev_err(dev, "Invalid number of inputs selected in DT\n"); + return -EINVAL; + } + + isl7998x->pd_gpio = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); + if (IS_ERR(isl7998x->pd_gpio)) { + dev_err(dev, "Failed to retrieve/request PD GPIO: %ld\n", + PTR_ERR(isl7998x->pd_gpio)); + return PTR_ERR(isl7998x->pd_gpio); + } + + isl7998x->regmap = devm_regmap_init_i2c(client, &isl7998x_regmap); + if (IS_ERR(isl7998x->regmap)) { + ret = PTR_ERR(isl7998x->regmap); + dev_err(dev, "Failed to allocate register map: %d\n", ret); + return ret; + } + + ep = of_graph_get_next_endpoint(dev->of_node, NULL); + if (!ep) { + dev_err(dev, "Missing endpoint node\n"); + return -EINVAL; + } + + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &endpoint); + of_node_put(ep); + if (ret) { + dev_err(dev, "Failed to parse endpoint\n"); + return ret; + } + + if (endpoint.bus_type != V4L2_MBUS_CSI2_DPHY || + endpoint.bus.mipi_csi2.num_data_lanes == 0 || + endpoint.bus.mipi_csi2.num_data_lanes > 2) { + dev_err(dev, "Invalid bus type or number of MIPI lanes\n"); + return -EINVAL; + } + + isl7998x->nr_mipi_lanes = endpoint.bus.mipi_csi2.num_data_lanes; + + v4l2_i2c_subdev_init(&isl7998x->subdev, client, &isl7998x_subdev_ops); + isl7998x->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + +#ifdef CONFIG_MEDIA_CONTROLLER + isl7998x->pad.flags = MEDIA_PAD_FL_SOURCE; + isl7998x->subdev.entity.ops = &isl7998x_entity_ops; + isl7998x->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; + ret = media_entity_pads_init(&isl7998x->subdev.entity, 1, + &isl7998x->pad); + if (ret < 0) + return ret; +#endif + + isl7998x->width = ISL7998x_WIDTH; + isl7998x->height = ISL7998x_HEIGHT; + isl7998x->fmt = &isl7998x_colour_fmts[0]; + + ret = v4l2_ctrl_handler_init(&isl7998x->ctrl_handler, + 2 + ARRAY_SIZE(isl7998x_ctrls)); + if (ret) + return ret; + + mutex_init(&isl7998x->ctrl_mutex); + isl7998x->ctrl_handler.lock = &isl7998x->ctrl_mutex; + isl7998x->link_freq = v4l2_ctrl_new_int_menu(&isl7998x->ctrl_handler, + &isl7998x_ctrl_ops, V4L2_CID_LINK_FREQ, + ARRAY_SIZE(link_freq_menu_items) - 1, + endpoint.bus.mipi_csi2.num_data_lanes == 2 ? + 1 : 0, link_freq_menu_items); + isl7998x->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; + + for (i = 0; i < ARRAY_SIZE(isl7998x_ctrls); i++) { + v4l2_ctrl_new_custom(&isl7998x->ctrl_handler, + &isl7998x_ctrls[i], NULL); + } + + v4l2_ctrl_new_std_menu_items(&isl7998x->ctrl_handler, + &isl7998x_ctrl_ops, V4L2_CID_TEST_PATTERN, + ARRAY_SIZE(isl7998x_test_pattern_menu) - 1, + 0, 0, isl7998x_test_pattern_menu); + + isl7998x->subdev.ctrl_handler = &isl7998x->ctrl_handler; + + isl7998x->subdev.dev = dev; + ret = v4l2_async_register_subdev(&isl7998x->subdev); + if (ret < 0) + goto err_entity_cleanup; + + /* + * Turn the chip ON and keep it ON, otherwise the camera standard + * detection takes about 600 mS every time we do VIDIOC_G_FMT. + */ + if (isl7998x->pd_gpio) + gpiod_set_value(isl7998x->pd_gpio, 0); + + ret = regmap_read(isl7998x->regmap, ISL7998x_REG_P0_PRODUCT_ID_CODE, + &chip_id); + if (ret) { + dev_err(dev, "Failed to read ID register: %d\n", ret); + goto err_init_cleanup; + } + + dev_info(dev, "ISL7998x found (id=%x)\n", chip_id); + + ret = isl7998x_init(isl7998x); + if (ret) + goto err_init_cleanup; + + ret = isl7998x_update_std(isl7998x); + if (ret) + goto err_init_cleanup; + + return 0; + +err_init_cleanup: + if (isl7998x->pd_gpio) + gpiod_set_value(isl7998x->pd_gpio, 1); +err_entity_cleanup: +#ifdef CONFIG_MEDIA_CONTROLLER + media_entity_cleanup(&isl7998x->subdev.entity); +#endif + return ret; +} + +static int isl7998x_remove(struct i2c_client *client) +{ + struct isl7998x *isl7998x = i2c_to_isl7998x(client); + + if (isl7998x->pd_gpio) + gpiod_set_value(isl7998x->pd_gpio, 1); + v4l2_async_unregister_subdev(&isl7998x->subdev); + v4l2_ctrl_handler_free(isl7998x->subdev.ctrl_handler); + media_entity_cleanup(&isl7998x->subdev.entity); + + return 0; +} + +static const struct of_device_id isl7998x_of_match[] = { + { .compatible = "isil,isl79987", }, + {}, +}; +MODULE_DEVICE_TABLE(of, isl7998x_of_match); + +static const struct i2c_device_id isl7998x_id[] = { + { "isl79987", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, isl7998x_id); + +static struct i2c_driver isl7998x_i2c_driver = { + .driver = { + .name = "isl7998x", + .of_match_table = of_match_ptr(isl7998x_of_match), + }, + .probe = isl7998x_probe, + .remove = isl7998x_remove, + .id_table = isl7998x_id, +}; + +module_i2c_driver(isl7998x_i2c_driver); + +MODULE_DESCRIPTION("Intersil ISL7998x BT656-to-MIPI-CSI2 driver"); +MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); +MODULE_LICENSE("GPL"); -- 2.20.1 ^ permalink raw reply related [flat|nested] 22+ messages in thread
* Re: [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x 2019-05-20 20:18 ` [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x Marek Vasut @ 2019-07-01 7:58 ` Jacopo Mondi 2019-08-06 14:03 ` Marek Vasut 2019-07-01 8:43 ` Sakari Ailus 2019-07-01 8:46 ` Sakari Ailus 2 siblings, 1 reply; 22+ messages in thread From: Jacopo Mondi @ 2019-07-01 7:58 UTC (permalink / raw) To: Marek Vasut; +Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring [-- Attachment #1: Type: text/plain, Size: 52310 bytes --] Hello Marek, long time due review, sorry about this. On Mon, May 20, 2019 at 10:18:12PM +0200, Marek Vasut wrote: > Add driver for the Intersil ISL7998x BT656-to-MIPI-CSI2 video decoder. analog to CSI-2 or analog to BT.656 if you want to support both chip versions. > This chip supports 1/2/4 analog video inputs and converts them into > 1/2/4 VCs in MIPI CSI2 stream. > > This driver currently supports ISL79987 and both 720x480 and 720x576 > resolutions, however as per specification, all inputs must use the > same resolution and standard. The only supported pixel format is now > YUYV/YUV422. The chip should support RGB565 on the CSI2 as well, but it's a media bus format, just mention YUYV > this is currently unsupported. > > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Sakari Ailus <sakari.ailus@linux.intel.com> > Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> > Cc: Rob Herring <robh+dt@kernel.org> > To: linux-media@vger.kernel.org > --- > drivers/media/i2c/Kconfig | 6 + > drivers/media/i2c/Makefile | 1 + > drivers/media/i2c/isl7998x.c | 1111 ++++++++++++++++++++++++++++++++++ > 3 files changed, 1118 insertions(+) > create mode 100644 drivers/media/i2c/isl7998x.c > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index 7793358ab8b3..af2ea08d6c59 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -929,6 +929,12 @@ config VIDEO_NOON010PC30 > help > This driver supports NOON010PC30 CIF camera from Siliconfile > > +config VIDEO_ISL7998X > + tristate "Intersil ISL7998x support" > + depends on I2C && VIDEO_V4L2 Don't you depend on OF too ? > + help > + This driver supports Intersil ISL7998x BT656-to-MIPI-CSI2 bridge. Please update this description as well as this chip is either CSI-2 or BT.565, not both. > + > source "drivers/media/i2c/m5mols/Kconfig" > > config VIDEO_RJ54N1 > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > index d8ad9dad495d..a66f105a7bcc 100644 > --- a/drivers/media/i2c/Makefile > +++ b/drivers/media/i2c/Makefile > @@ -113,6 +113,7 @@ obj-$(CONFIG_VIDEO_IMX258) += imx258.o > obj-$(CONFIG_VIDEO_IMX274) += imx274.o > obj-$(CONFIG_VIDEO_IMX319) += imx319.o > obj-$(CONFIG_VIDEO_IMX355) += imx355.o > +obj-$(CONFIG_VIDEO_ISL7998X) += isl7998x.o > obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o > > obj-$(CONFIG_SDR_MAX2175) += max2175.o > diff --git a/drivers/media/i2c/isl7998x.c b/drivers/media/i2c/isl7998x.c > new file mode 100644 > index 000000000000..858e98d8b494 > --- /dev/null > +++ b/drivers/media/i2c/isl7998x.c > @@ -0,0 +1,1111 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Intersil ISL7998x BT656-to-MIPI-CSI2 driver Here as well. > + * > + * Copyright (C) 2018-2019 Marek Vasut <marex@denx.de> > + */ > +#include <linux/videodev2.h> Sorting inclusion alphabetically is always nice and help finding duplicates. > +#include <linux/delay.h> > +#include <linux/gpio.h> > +#include <linux/i2c.h> > +#include <linux/log2.h> > +#include <linux/module.h> > +#include <linux/of_graph.h> > +#include <linux/regmap.h> > +#include <linux/slab.h> > +#include <linux/v4l2-mediabus.h> > +#include <media/v4l2-async.h> > +#include <media/v4l2-clk.h> > +#include <media/v4l2-common.h> > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-fwnode.h> > + > +#define ISL7998x_WIDTH 720 > +#define ISL7998x_HEIGHT 480 > +#define ISL7998x_INPUTS 4 > + > +#define V4L2_CID_TEST_PATTERN_COLOR (V4L2_CID_USER_BASE | 0x1001) > +#define V4L2_CID_TEST_PATTERN_CHANNELS (V4L2_CID_USER_BASE | 0x1002) > +#define V4L2_CID_TEST_PATTERN_BARS (V4L2_CID_USER_BASE | 0x1003) > + > +#define ISL7998x_REG(page, reg) (((page) << 8) | (reg)) > + > +#define ISL7998x_REG_Pn_SIZE 256 > +#define ISL7998x_REG_Pn_BASE(n) ((n) * ISL7998x_REG_Pn_SIZE) > + > +#define ISL7998x_REG_Px_DEC_PAGE(page) ISL7998x_REG((page), 0xff) > +#define ISL7998x_REG_Px_DEC_PAGE_MASK 0xf > +#define ISL7998x_REG_P0_PRODUCT_ID_CODE ISL7998x_REG(0, 0x00) > +#define ISL7998x_REG_P0_PRODUCT_REV_CODE ISL7998x_REG(0, 0x01) > +#define ISL7998x_REG_P0_SW_RESET_CTL ISL7998x_REG(0, 0x02) > +#define ISL7998x_REG_P0_IO_BUFFER_CTL ISL7998x_REG(0, 0x03) > +#define ISL7998x_REG_P0_IO_BUFFER_CTL_1_1 ISL7998x_REG(0, 0x04) > +#define ISL7998x_REG_P0_IO_PAD_PULL_EN_CTL ISL7998x_REG(0, 0x05) > +#define ISL7998x_REG_P0_IO_BUFFER_CTL_1_2 ISL7998x_REG(0, 0x06) > +#define ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL ISL7998x_REG(0, 0x07) > +#define ISL7998x_REG_P0_CLK_CTL_1 ISL7998x_REG(0, 0x08) > +#define ISL7998x_REG_P0_CLK_CTL_2 ISL7998x_REG(0, 0x09) > +#define ISL7998x_REG_P0_CLK_CTL_3 ISL7998x_REG(0, 0x0a) > +#define ISL7998x_REG_P0_CLK_CTL_4 ISL7998x_REG(0, 0x0b) > +#define ISL7998x_REG_P0_MPP1_SYNC_CTL ISL7998x_REG(0, 0x0c) > +#define ISL7998x_REG_P0_MPP2_SYNC_CTL ISL7998x_REG(0, 0x0d) > +#define ISL7998x_REG_P0_IRQ_SYNC_CTL ISL7998x_REG(0, 0x0e) > +#define ISL7998x_REG_P0_INTERRUPT_STATUS ISL7998x_REG(0, 0x10) > +#define ISL7998x_REG_P0_CHAN_1_IRQ ISL7998x_REG(0, 0x11) > +#define ISL7998x_REG_P0_CHAN_2_IRQ ISL7998x_REG(0, 0x12) > +#define ISL7998x_REG_P0_CHAN_3_IRQ ISL7998x_REG(0, 0x13) > +#define ISL7998x_REG_P0_CHAN_4_IRQ ISL7998x_REG(0, 0x14) > +#define ISL7998x_REG_P0_SHORT_DIAG_IRQ ISL7998x_REG(0, 0x15) > +#define ISL7998x_REG_P0_CHAN_1_IRQ_EN ISL7998x_REG(0, 0x16) > +#define ISL7998x_REG_P0_CHAN_2_IRQ_EN ISL7998x_REG(0, 0x17) > +#define ISL7998x_REG_P0_CHAN_3_IRQ_EN ISL7998x_REG(0, 0x18) > +#define ISL7998x_REG_P0_CHAN_4_IRQ_EN ISL7998x_REG(0, 0x19) > +#define ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN ISL7998x_REG(0, 0x1a) > +#define ISL7998x_REG_P0_CHAN_1_STATUS ISL7998x_REG(0, 0x1b) > +#define ISL7998x_REG_P0_CHAN_2_STATUS ISL7998x_REG(0, 0x1c) > +#define ISL7998x_REG_P0_CHAN_3_STATUS ISL7998x_REG(0, 0x1d) > +#define ISL7998x_REG_P0_CHAN_4_STATUS ISL7998x_REG(0, 0x1e) > +#define ISL7998x_REG_P0_SHORT_DIAG_STATUS ISL7998x_REG(0, 0x1f) > +#define ISL7998x_REG_P0_CLOCK_DELAY ISL7998x_REG(0, 0x20) > + > +#define ISL7998x_REG_Px_DEC_INPUT_FMT(pg) ISL7998x_REG((pg), 0x02) > +#define ISL7998x_REG_Px_DEC_STATUS_1(pg) ISL7998x_REG((pg), 0x03) > +#define ISL7998x_REG_Px_DEC_HS_DELAY_CTL(pg) ISL7998x_REG((pg), 0x04) > +#define ISL7998x_REG_Px_DEC_ANCTL(pg) ISL7998x_REG((pg), 0x06) > +#define ISL7998x_REG_Px_DEC_CROP_HI(pg) ISL7998x_REG((pg), 0x07) > +#define ISL7998x_REG_Px_DEC_VDELAY_LO(pg) ISL7998x_REG((pg), 0x08) > +#define ISL7998x_REG_Px_DEC_VACTIVE_LO(pg) ISL7998x_REG((pg), 0x09) > +#define ISL7998x_REG_Px_DEC_HDELAY_LO(pg) ISL7998x_REG((pg), 0x0a) > +#define ISL7998x_REG_Px_DEC_HACTIVE_LO(pg) ISL7998x_REG((pg), 0x0b) > +#define ISL7998x_REG_Px_DEC_CNTRL1(pg) ISL7998x_REG((pg), 0x0c) > +#define ISL7998x_REG_Px_DEC_CSC_CTL(pg) ISL7998x_REG((pg), 0x0d) > +#define ISL7998x_REG_Px_DEC_BRIGHT(pg) ISL7998x_REG((pg), 0x10) > +#define ISL7998x_REG_Px_DEC_CONTRAST(pg) ISL7998x_REG((pg), 0x11) > +#define ISL7998x_REG_Px_DEC_SHARPNESS(pg) ISL7998x_REG((pg), 0x12) > +#define ISL7998x_REG_Px_DEC_SAT_U(pg) ISL7998x_REG((pg), 0x13) > +#define ISL7998x_REG_Px_DEC_SAT_V(pg) ISL7998x_REG((pg), 0x14) > +#define ISL7998x_REG_Px_DEC_HUE(pg) ISL7998x_REG((pg), 0x15) > +#define ISL7998x_REG_Px_DEC_VERT_PEAK(pg) ISL7998x_REG((pg), 0x17) > +#define ISL7998x_REG_Px_DEC_CORING(pg) ISL7998x_REG((pg), 0x18) > +#define ISL7998x_REG_Px_DEC_SDT(pg) ISL7998x_REG((pg), 0x1c) > +#define ISL7998x_REG_Px_DEC_SDT_DET BIT(7) > +#define ISL7998x_REG_Px_DEC_SDTR(pg) ISL7998x_REG((pg), 0x1d) > +#define ISL7998x_REG_Px_DEC_CLMPG(pg) ISL7998x_REG((pg), 0x20) > +#define ISL7998x_REG_Px_DEC_IAGC(pg) ISL7998x_REG((pg), 0x21) > +#define ISL7998x_REG_Px_DEC_AGCGAIN(pg) ISL7998x_REG((pg), 0x22) > +#define ISL7998x_REG_Px_DEC_PEAKWT(pg) ISL7998x_REG((pg), 0x23) > +#define ISL7998x_REG_Px_DEC_CLMPL(pg) ISL7998x_REG((pg), 0x24) > +#define ISL7998x_REG_Px_DEC_SYNCT(pg) ISL7998x_REG((pg), 0x25) > +#define ISL7998x_REG_Px_DEC_MISSCNT(pg) ISL7998x_REG((pg), 0x26) > +#define ISL7998x_REG_Px_DEC_PCLAMP(pg) ISL7998x_REG((pg), 0x27) > +#define ISL7998x_REG_Px_DEC_VERT_CTL_1(pg) ISL7998x_REG((pg), 0x28) > +#define ISL7998x_REG_Px_DEC_VERT_CTL_2(pg) ISL7998x_REG((pg), 0x29) > +#define ISL7998x_REG_Px_DEC_CLR_KILL_LVL(pg) ISL7998x_REG((pg), 0x2a) > +#define ISL7998x_REG_Px_DEC_COMB_FILTER_CTL(pg) ISL7998x_REG((pg), 0x2b) > +#define ISL7998x_REG_Px_DEC_LUMA_DELAY(pg) ISL7998x_REG((pg), 0x2c) > +#define ISL7998x_REG_Px_DEC_MISC1(pg) ISL7998x_REG((pg), 0x2d) > +#define ISL7998x_REG_Px_DEC_MISC2(pg) ISL7998x_REG((pg), 0x2e) > +#define ISL7998x_REG_Px_DEC_MISC3(pg) ISL7998x_REG((pg), 0x2f) > +#define ISL7998x_REG_Px_DEC_MVSN(pg) ISL7998x_REG((pg), 0x30) > +#define ISL7998x_REG_Px_DEC_CSTATUS2(pg) ISL7998x_REG((pg), 0x31) > +#define ISL7998x_REG_Px_DEC_HFREF(pg) ISL7998x_REG((pg), 0x32) > +#define ISL7998x_REG_Px_DEC_CLMD(pg) ISL7998x_REG((pg), 0x33) > +#define ISL7998x_REG_Px_DEC_ID_DET_CTL(pg) ISL7998x_REG((pg), 0x34) > +#define ISL7998x_REG_Px_DEC_CLCNTL(pg) ISL7998x_REG((pg), 0x35) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_1(pg) ISL7998x_REG((pg), 0x36) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_2(pg) ISL7998x_REG((pg), 0x37) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_3(pg) ISL7998x_REG((pg), 0x38) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_4(pg) ISL7998x_REG((pg), 0x39) > +#define ISL7998x_REG_Px_DEC_SHORT_DET_CTL(pg) ISL7998x_REG((pg), 0x3a) > +#define ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(pg) ISL7998x_REG((pg), 0x3b) > +#define ISL7998x_REG_Px_DEC_AFE_TST_MUX_CTL(pg) ISL7998x_REG((pg), 0x3c) > +#define ISL7998x_REG_Px_DEC_DATA_CONV(pg) ISL7998x_REG((pg), 0x3d) > +#define ISL7998x_REG_Px_DEC_INTERNAL_TEST(pg) ISL7998x_REG((pg), 0x3f) > +#define ISL7998x_REG_Px_DEC_H_DELAY_CTL(pg) ISL7998x_REG((pg), 0x43) > +#define ISL7998x_REG_Px_DEC_H_DELAY_II_HI(pg) ISL7998x_REG((pg), 0x44) > +#define ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(pg) ISL7998x_REG((pg), 0x45) > + > +#define ISL7998x_REG_Px_ACA_CTL_1(pg) ISL7998x_REG((pg), 0x80) > +#define ISL7998x_REG_Px_ACA_GAIN_CTL(pg) ISL7998x_REG((pg), 0x81) > +#define ISL7998x_REG_Px_ACA_Y_AVG_HI_LIMIT(pg) ISL7998x_REG((pg), 0x82) > +#define ISL7998x_REG_Px_ACA_Y_AVG_LO_LIMIT(pg) ISL7998x_REG((pg), 0x83) > +#define ISL7998x_REG_Px_ACA_Y_DET_THRESHOLD(pg) ISL7998x_REG((pg), 0x84) > +#define ISL7998x_REG_Px_ACA_BLACK_LVL(pg) ISL7998x_REG((pg), 0x85) > +#define ISL7998x_REG_Px_ACA_CENTER_LVL(pg) ISL7998x_REG((pg), 0x86) > +#define ISL7998x_REG_Px_ACA_WHITE_LVL(pg) ISL7998x_REG((pg), 0x87) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_LIMIT(pg) ISL7998x_REG((pg), 0x88) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_UPGAIN(pg) ISL7998x_REG((pg), 0x89) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_SLOPE(pg) ISL7998x_REG((pg), 0x8a) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_DNGAIN(pg) ISL7998x_REG((pg), 0x8b) > +#define ISL7998x_REG_Px_ACA_DELTA_CO_THRES(pg) ISL7998x_REG((pg), 0x8c) > +#define ISL7998x_REG_Px_ACA_DELTA_SLOPE(pg) ISL7998x_REG((pg), 0x8d) > +#define ISL7998x_REG_Px_ACA_LO_HI_AVG_THRES(pg) ISL7998x_REG((pg), 0x8e) > +#define ISL7998x_REG_Px_ACA_LO_MAX_LVL_CTL(pg) ISL7998x_REG((pg), 0x8f) > +#define ISL7998x_REG_Px_ACA_HI_MAX_LVL_CTL(pg) ISL7998x_REG((pg), 0x90) > +#define ISL7998x_REG_Px_ACA_LO_UPGAIN_CTL(pg) ISL7998x_REG((pg), 0x91) > +#define ISL7998x_REG_Px_ACA_LO_DNGAIN_CTL(pg) ISL7998x_REG((pg), 0x92) > +#define ISL7998x_REG_Px_ACA_HI_UPGAIN_CTL(pg) ISL7998x_REG((pg), 0x93) > +#define ISL7998x_REG_Px_ACA_HI_DNGAIN_CTL(pg) ISL7998x_REG((pg), 0x94) > +#define ISL7998x_REG_Px_ACA_LOPASS_FLT_COEF(pg) ISL7998x_REG((pg), 0x95) > +#define ISL7998x_REG_Px_ACA_PDF_INDEX(pg) ISL7998x_REG((pg), 0x96) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_STT(pg) ISL7998x_REG((pg), 0x97) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_SZ1(pg) ISL7998x_REG((pg), 0x98) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_SZ2(pg) ISL7998x_REG((pg), 0x99) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_STT(pg) ISL7998x_REG((pg), 0x9a) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ1(pg) ISL7998x_REG((pg), 0x9b) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(pg) ISL7998x_REG((pg), 0x9c) > +#define ISL7998x_REG_Px_ACA_Y_AVG(pg) ISL7998x_REG((pg), 0xa0) > +#define ISL7998x_REG_Px_ACA_Y_AVG_LIM(pg) ISL7998x_REG((pg), 0xa1) > +#define ISL7998x_REG_Px_ACA_LO_AVG(pg) ISL7998x_REG((pg), 0xa2) > +#define ISL7998x_REG_Px_ACA_HI_AVG(pg) ISL7998x_REG((pg), 0xa3) > +#define ISL7998x_REG_Px_ACA_Y_MAX(pg) ISL7998x_REG((pg), 0xa4) > +#define ISL7998x_REG_Px_ACA_Y_MIN(pg) ISL7998x_REG((pg), 0xa5) > +#define ISL7998x_REG_Px_ACA_MOFFSET(pg) ISL7998x_REG((pg), 0xa6) > +#define ISL7998x_REG_Px_ACA_LO_GAIN(pg) ISL7998x_REG((pg), 0xa7) > +#define ISL7998x_REG_Px_ACA_HI_GAIN(pg) ISL7998x_REG((pg), 0xa8) > +#define ISL7998x_REG_Px_ACA_LL_SLOPE(pg) ISL7998x_REG((pg), 0xa9) > +#define ISL7998x_REG_Px_ACA_LH_SLOPE(pg) ISL7998x_REG((pg), 0xaa) > +#define ISL7998x_REG_Px_ACA_HL_SLOPE(pg) ISL7998x_REG((pg), 0xab) > +#define ISL7998x_REG_Px_ACA_HH_SLOPE(pg) ISL7998x_REG((pg), 0xac) > +#define ISL7998x_REG_Px_ACA_X_LOW(pg) ISL7998x_REG((pg), 0xad) > +#define ISL7998x_REG_Px_ACA_X_MEAN(pg) ISL7998x_REG((pg), 0xae) > +#define ISL7998x_REG_Px_ACA_X_HIGH(pg) ISL7998x_REG((pg), 0xaf) > +#define ISL7998x_REG_Px_ACA_Y_LOW(pg) ISL7998x_REG((pg), 0xb0) > +#define ISL7998x_REG_Px_ACA_Y_MEAN(pg) ISL7998x_REG((pg), 0xb1) > +#define ISL7998x_REG_Px_ACA_Y_HIGH(pg) ISL7998x_REG((pg), 0xb2) > +#define ISL7998x_REG_Px_ACA_CTL_2(pg) ISL7998x_REG((pg), 0xb3) > +#define ISL7998x_REG_Px_ACA_CTL_3(pg) ISL7998x_REG((pg), 0xb4) > +#define ISL7998x_REG_Px_ACA_CTL_4(pg) ISL7998x_REG((pg), 0xb5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(pg) ISL7998x_REG((pg), 0xc0) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TL_H(pg) ISL7998x_REG((pg), 0xc1) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TL_L(pg) ISL7998x_REG((pg), 0xc2) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TL_H(pg) ISL7998x_REG((pg), 0xc3) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TL_L(pg) ISL7998x_REG((pg), 0xc4) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TR_H(pg) ISL7998x_REG((pg), 0xc5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TR_L(pg) ISL7998x_REG((pg), 0xc6) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TR_H(pg) ISL7998x_REG((pg), 0xc7) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TR_L(pg) ISL7998x_REG((pg), 0xc8) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BL_H(pg) ISL7998x_REG((pg), 0xc9) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BL_L(pg) ISL7998x_REG((pg), 0xca) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BL_H(pg) ISL7998x_REG((pg), 0xcb) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BL_L(pg) ISL7998x_REG((pg), 0xcc) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BR_H(pg) ISL7998x_REG((pg), 0xcd) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BR_L(pg) ISL7998x_REG((pg), 0xce) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BR_H(pg) ISL7998x_REG((pg), 0xcf) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BR_L(pg) ISL7998x_REG((pg), 0xd0) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_LM_H(pg) ISL7998x_REG((pg), 0xd1) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_LM_L(pg) ISL7998x_REG((pg), 0xd2) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_LM_H(pg) ISL7998x_REG((pg), 0xd3) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_LM_L(pg) ISL7998x_REG((pg), 0xd4) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TM_H(pg) ISL7998x_REG((pg), 0xd5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TM_L(pg) ISL7998x_REG((pg), 0xd6) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TM_H(pg) ISL7998x_REG((pg), 0xd7) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TM_L(pg) ISL7998x_REG((pg), 0xd8) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BM_H(pg) ISL7998x_REG((pg), 0xd9) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BM_L(pg) ISL7998x_REG((pg), 0xda) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BM_H(pg) ISL7998x_REG((pg), 0xdb) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BM_L(pg) ISL7998x_REG((pg), 0xdc) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_RM_H(pg) ISL7998x_REG((pg), 0xdd) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_RM_L(pg) ISL7998x_REG((pg), 0xde) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_RM_H(pg) ISL7998x_REG((pg), 0xdf) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_RM_L(pg) ISL7998x_REG((pg), 0xe0) > +#define ISL7998x_REG_Px_ACA_HIST_DATA_LO(pg) ISL7998x_REG((pg), 0xe1) > +#define ISL7998x_REG_Px_ACA_HIST_DATA_MID(pg) ISL7998x_REG((pg), 0xe2) > +#define ISL7998x_REG_Px_ACA_HIST_DATA_HI(pg) ISL7998x_REG((pg), 0xe3) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_CLR(pg) ISL7998x_REG((pg), 0xe4) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_CB_CLR(pg) ISL7998x_REG((pg), 0xe5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(pg) ISL7998x_REG((pg), 0xe6) > +#define ISL7998x_REG_Px_ACA_XFER_HIST_HOST(pg) ISL7998x_REG((pg), 0xe7) > + > +#define ISL7998x_REG_P5_LI_ENGINE_CTL ISL7998x_REG(5, 0x00) > +#define ISL7998x_REG_P5_LI_ENGINE_LINE_CTL ISL7998x_REG(5, 0x01) > +#define ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH ISL7998x_REG(5, 0x02) > +#define ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL ISL7998x_REG(5, 0x03) > +#define ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT ISL7998x_REG(5, 0x04) > +#define ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL ISL7998x_REG(5, 0x05) > +#define ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL ISL7998x_REG(5, 0x06) > +#define ISL7998x_REG_P5_MIPI_READ_START_CTL ISL7998x_REG(5, 0x07) > +#define ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL ISL7998x_REG(5, 0x08) > +#define ISL7998x_REG_P5_ONE_FIELD_MODE_CTL ISL7998x_REG(5, 0x09) > +#define ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR ISL7998x_REG(5, 0x0a) > +#define ISL7998x_REG_P5_TP_GEN_BAR_PATTERN ISL7998x_REG(5, 0x0b) > +#define ISL7998x_REG_P5_MIPI_PCNT_PSFRM ISL7998x_REG(5, 0x0c) > +#define ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL ISL7998x_REG(5, 0x0d) > +#define ISL7998x_REG_P5_MIPI_VBLANK_PSFRM ISL7998x_REG(5, 0x0e) > +#define ISL7998x_REG_P5_LI_ENGINE_CTL_2 ISL7998x_REG(5, 0x0f) > +#define ISL7998x_REG_P5_MIPI_WCNT_1 ISL7998x_REG(5, 0x10) > +#define ISL7998x_REG_P5_MIPI_WCNT_2 ISL7998x_REG(5, 0x11) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1 ISL7998x_REG(5, 0x12) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2 ISL7998x_REG(5, 0x13) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3 ISL7998x_REG(5, 0x14) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4 ISL7998x_REG(5, 0x15) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5 ISL7998x_REG(5, 0x16) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6 ISL7998x_REG(5, 0x17) > +#define ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1 ISL7998x_REG(5, 0x18) > +#define ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD ISL7998x_REG(5, 0x19) > +#define ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD ISL7998x_REG(5, 0x1a) > +#define ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2 ISL7998x_REG(5, 0x1b) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7 ISL7998x_REG(5, 0x1c) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8 ISL7998x_REG(5, 0x1d) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9 ISL7998x_REG(5, 0x1e) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_10 ISL7998x_REG(5, 0x1f) > +#define ISL7998x_REG_P5_TP_GEN_MIPI ISL7998x_REG(5, 0x20) > +#define ISL7998x_REG_P5_ESC_MODE_TIME_CTL ISL7998x_REG(5, 0x21) > +#define ISL7998x_REG_P5_AUTO_TEST_ERR_DET ISL7998x_REG(5, 0x22) > +#define ISL7998x_REG_P5_MIPI_TIMING ISL7998x_REG(5, 0x23) > +#define ISL7998x_REG_P5_PIC_HEIGHT_HIGH ISL7998x_REG(5, 0x24) > +#define ISL7998x_REG_P5_PIC_HEIGHT_LOW ISL7998x_REG(5, 0x25) > +#define ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL ISL7998x_REG(5, 0x26) > +#define ISL7998x_REG_P5_FIFO_THRSH_CNT_1 ISL7998x_REG(5, 0x28) > +#define ISL7998x_REG_P5_FIFO_THRSH_CNT_2 ISL7998x_REG(5, 0x29) > +#define ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1 ISL7998x_REG(5, 0x2a) > +#define ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2 ISL7998x_REG(5, 0x2b) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_1 ISL7998x_REG(5, 0x2c) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_2 ISL7998x_REG(5, 0x2d) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_3 ISL7998x_REG(5, 0x2e) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_4 ISL7998x_REG(5, 0x2f) > +#define ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1 ISL7998x_REG(5, 0x30) > +#define ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2 ISL7998x_REG(5, 0x31) > +#define ISL7998x_REG_P5_MIPI_ANA_CLK_CTL ISL7998x_REG(5, 0x32) > +#define ISL7998x_REG_P5_PLL_ANA_STATUS ISL7998x_REG(5, 0x33) > +#define ISL7998x_REG_P5_PLL_ANA_MISC_CTL ISL7998x_REG(5, 0x34) > +#define ISL7998x_REG_P5_MIPI_ANA ISL7998x_REG(5, 0x35) > +#define ISL7998x_REG_P5_PLL_ANA ISL7998x_REG(5, 0x36) > +#define ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1 ISL7998x_REG(5, 0x38) > +#define ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2 ISL7998x_REG(5, 0x39) > +#define ISL7998x_REG_P5_H_LINE_CNT_1 ISL7998x_REG(5, 0x3a) > +#define ISL7998x_REG_P5_H_LINE_CNT_2 ISL7998x_REG(5, 0x3b) > +#define ISL7998x_REG_P5_HIST_LINE_CNT_1 ISL7998x_REG(5, 0x3c) > +#define ISL7998x_REG_P5_HIST_LINE_CNT_2 ISL7998x_REG(5, 0x3d) Not all the above definitions are used. While it doesn't hurt to have them here, it's a pretty scary list of registers entries. > + > +static const struct reg_sequence isl7998x_init_seq_1[] = { > + { ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN, 0xff }, > + { ISL7998x_REG_Px_DEC_SDT(0x1), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x1), 0x03 }, > + { ISL7998x_REG_Px_DEC_SDT(0x2), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x2), 0x03 }, > + { ISL7998x_REG_Px_DEC_SDT(0x3), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x3), 0x03 }, > + { ISL7998x_REG_Px_DEC_SDT(0x4), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x4), 0x03 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x00 }, > + { ISL7998x_REG_P0_SW_RESET_CTL, 0x1f, 10 }, > + { ISL7998x_REG_P0_IO_BUFFER_CTL, 0x00 }, > + { ISL7998x_REG_P0_MPP2_SYNC_CTL, 0xc9 }, > + { ISL7998x_REG_P0_IRQ_SYNC_CTL, 0xc9 }, > + { ISL7998x_REG_P0_CHAN_1_IRQ, 0x03 }, > + { ISL7998x_REG_P0_CHAN_2_IRQ, 0x00 }, > + { ISL7998x_REG_P0_CHAN_3_IRQ, 0x00 }, > + { ISL7998x_REG_P0_CHAN_4_IRQ, 0x00 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x02 }, > + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, 0x85 }, > + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, 0xa0 }, > + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x18 }, > + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x40 }, > + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x40 }, > + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, > + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, > + { ISL7998x_REG_P5_TP_GEN_MIPI, 0x00 }, > + { ISL7998x_REG_P5_ESC_MODE_TIME_CTL, 0x0c }, > + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x00 }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x19 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_1, 0x18 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_2, 0xf1 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_3, 0x00 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_4, 0xf1 }, > + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1, 0x00 }, > + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2, 0x00 }, > + { ISL7998x_REG_P5_MIPI_ANA_CLK_CTL, 0x00 }, > + { ISL7998x_REG_P5_PLL_ANA_STATUS, 0xc0 }, > + { ISL7998x_REG_P5_PLL_ANA_MISC_CTL, 0x18 }, > + { ISL7998x_REG_P5_PLL_ANA, 0x00 }, > + { ISL7998x_REG_P0_SW_RESET_CTL, 0x10, 10 }, > + /* Page 0xf means write to all of pages 1,2,3,4 */ > + { ISL7998x_REG_Px_DEC_VDELAY_LO(0xf), 0x14 }, > + { ISL7998x_REG_Px_DEC_MISC3(0xf), 0xe6 }, > + { ISL7998x_REG_Px_DEC_CLMD(0xf), 0x85 }, > + { ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(0xf), 0x11 }, > + { ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), 0x00 }, > + { ISL7998x_REG_P0_CLK_CTL_1, 0x1f }, > + { ISL7998x_REG_P0_CLK_CTL_2, 0x43 }, > + { ISL7998x_REG_P0_CLK_CTL_3, 0x4f }, > +}; > + > +static const struct reg_sequence isl7998x_init_seq_2[] = { Is seq_2 alternative to the first? Care to comment a bit what these do, if we have to live with register writes sequences? > + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x10 }, > + { ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT, 0xe4 }, > + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x00 }, > + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x60 }, > + { ISL7998x_REG_P5_MIPI_READ_START_CTL, 0x2b }, > + { ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL, 0x02 }, > + { ISL7998x_REG_P5_ONE_FIELD_MODE_CTL, 0x00 }, > + { ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR, 0x62 }, > + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, 0x02 }, > + { ISL7998x_REG_P5_MIPI_PCNT_PSFRM, 0x36 }, > + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0x00 }, > + { ISL7998x_REG_P5_MIPI_VBLANK_PSFRM, 0x6c }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0x00 }, > + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, > + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1, 0x77 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2, 0x17 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3, 0x08 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4, 0x38 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5, 0x14 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6, 0xf6 }, > + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1, 0x00 }, > + { ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD, 0x17 }, > + { ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD, 0x0a }, > + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2, 0x71 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7, 0x7a }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8, 0x0f }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9, 0x8c }, > + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x08 }, > + { ISL7998x_REG_P5_FIFO_THRSH_CNT_1, 0x01 }, > + { ISL7998x_REG_P5_FIFO_THRSH_CNT_2, 0x0e }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x00 }, > + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, 0x03 }, > + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2, 0xc0 }, > + { ISL7998x_REG_P5_H_LINE_CNT_1, 0x06 }, > + { ISL7998x_REG_P5_H_LINE_CNT_2, 0xb3 }, > + { ISL7998x_REG_P5_HIST_LINE_CNT_1, 0x00 }, > + { ISL7998x_REG_P5_HIST_LINE_CNT_2, 0xf1 }, > + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x00 }, > + { ISL7998x_REG_P5_MIPI_ANA, 0x00 }, > + /* > + * Wait a bit after reset so that the chip can capture a frame > + * and update internal line counters. > + */ > + { ISL7998x_REG_P0_SW_RESET_CTL, 0x00, 50 }, > +}; > + > +struct isl7998x_datafmt { > + u32 code; > + enum v4l2_colorspace colorspace; > +}; > + > +static const struct isl7998x_datafmt isl7998x_colour_fmts[] = { > + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_SRGB }, You set the colorspace to 0 in s/g_fmt, while you could simply hardcode SRGB if you know that's the one the chip provides (which seems reasonable). > +}; > + > +/* Menu items for LINK_FREQ V4L2 control */ > +static const s64 link_freq_menu_items[] = { > + 108000000, 216000000, 432000000 > +}; > + > +/* Menu items for TEST_PATTERN V4L2 control */ > +static const char * const isl7998x_test_pattern_menu[] = { > + "Disabled", "Enabled-PAL (720x576)", "Enabled-NTSC (720x480)" > +}; > + > +struct isl7998x { > + struct v4l2_subdev subdev; > + struct regmap *regmap; > + struct gpio_desc *pd_gpio; > + unsigned int nr_mipi_lanes; > + u32 nr_inputs; > + > + unsigned int width; > + unsigned int height; > + const struct isl7998x_datafmt *fmt; > +#ifdef CONFIG_MEDIA_CONTROLLER > + struct media_pad pad; > +#endif > + > + struct v4l2_ctrl_handler ctrl_handler; > + struct mutex ctrl_mutex; it's common practice to state what a mutex protect if it's part of the device structure. Care to do so? > + /* V4L2 Controls */ > + struct v4l2_ctrl *link_freq; > + u8 test_pattern_enabled; > + u8 test_pattern_bars; > + u8 test_pattern_chans; > + u8 test_pattern_color; > +}; > + > +static struct isl7998x *sd_to_isl7998x(struct v4l2_subdev *sd) > +{ > + return container_of(sd, struct isl7998x, subdev); > +} > + > +static struct isl7998x *i2c_to_isl7998x(const struct i2c_client *client) > +{ > + return sd_to_isl7998x(i2c_get_clientdata(client)); > +} > + > +static int isl7998x_init(struct isl7998x *isl7998x) > +{ > + const unsigned int lanes = isl7998x->nr_mipi_lanes; > + const u32 isl7998x_video_in_chan_map[] = { 0x00, 0x11, 0x02, 0x02 }; > + const struct reg_sequence isl7998x_init_seq_custom[] = { > + { ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL, > + isl7998x_video_in_chan_map[isl7998x->nr_inputs - 1] }, > + { ISL7998x_REG_P0_CLK_CTL_4, (lanes == 1) ? 0x40 : 0x41 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL, (lanes == 1) ? 0x01 : 0x02 }, > + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, > + 0x20 | ((isl7998x->width >> 7) & 0x1f) }, > + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, > + (isl7998x->width << 1) & 0xff }, > + }; > + struct regmap *regmap = isl7998x->regmap; > + int ret; > + > + ret = regmap_register_patch(regmap, isl7998x_init_seq_1, > + ARRAY_SIZE(isl7998x_init_seq_1)); > + if (ret) > + return ret; > + > + ret = regmap_register_patch(regmap, isl7998x_init_seq_custom, > + ARRAY_SIZE(isl7998x_init_seq_custom)); > + if (ret) > + return ret; > + > + return regmap_register_patch(regmap, isl7998x_init_seq_2, > + ARRAY_SIZE(isl7998x_init_seq_2)); > +} > + > +static int isl7998x_g_mbus_config(struct v4l2_subdev *sd, > + struct v4l2_mbus_config *cfg) g_mbus_configg (as well as s_mbus_config) is deprecated. Does your bridge driver -really- need this? What platform is that? > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + > + cfg->type = V4L2_MBUS_CSI2_DPHY; > + cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; > + if (isl7998x->nr_mipi_lanes == 1) > + cfg->flags |= V4L2_MBUS_CSI2_1_LANE; > + else > + cfg->flags |= V4L2_MBUS_CSI2_2_LANE; > + > + return 0; > +} > + > +static int isl7998x_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + > + return isl7998x_init(isl7998x); > +} > + > +static int isl7998x_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->pad || code->index >= ARRAY_SIZE(isl7998x_colour_fmts)) > + return -EINVAL; > + > + code->code = isl7998x_colour_fmts[code->index].code; > + return 0; > +} > + > +static const unsigned int isl7998x_std_res[] = { > + 480, 576, 576, 480, 480, 576, 480, 480 > +}; > + > +static int isl7998x_update_std(struct isl7998x *isl7998x) > +{ > + unsigned int height[ISL7998x_INPUTS]; > + u8 scanning = GENMASK(ISL7998x_INPUTS - 1, 0); > + unsigned int i; > + int ret; > + u32 reg; > + > + while (true) { > + for (i = 0; i < ISL7998x_INPUTS; i++) { Cycle on all inputs or just the active ones? > + ret = regmap_read(isl7998x->regmap, > + ISL7998x_REG_Px_DEC_SDT(i + 1), ®); > + if (ret) > + return ret; > + > + /* Detection is still in progress, restart. */ > + if (reg & ISL7998x_REG_Px_DEC_SDT_DET) { > + scanning = GENMASK(ISL7998x_INPUTS - 1, 0); > + break; > + } > + > + scanning &= ~BIT(i); > + height[i] = isl7998x_std_res[(reg >> 4) & 0x7]; > + } > + > + if (!scanning) > + break; > + > + mdelay(1); mm, seems quite an arbitrary value here. Do you have a better characterization in the manual, and could you use usleep_range() to help the scheduler to coalesce wake-ups ? > + } > + > + /* > + * According to Renesas FAE, all input cameras must have the > + * same standard on this chip. > + */ > + for (i = 1; i < isl7998x->nr_inputs ; i++) > + if (height[i - 1] != height[i]) What about width? Ah seems like only 720 is accepted. > + return -EINVAL; > + > + isl7998x->height = height[0]; > + > + return 0; > +} > + > +static int isl7998x_get_fmt(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *format) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + struct v4l2_mbus_framefmt *mf = &format->format; > + > + if (format->pad != 0) > + return -EINVAL; > + > + if (isl7998x->test_pattern_enabled == 1) { > + mf->width = 720; > + mf->height = 576; > + } else if (isl7998x->test_pattern_enabled == 2) { > + mf->width = 720; > + mf->height = 480; > + } else { > + mf->width = isl7998x->width; > + mf->height = isl7998x->height; > + } > + > + mf->code = isl7998x->fmt->code; > + mf->field = V4L2_FIELD_INTERLACED; > + mf->colorspace = 0; > + > + return 0; > +} > + > +static int isl7998x_set_fmt(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *format) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + struct v4l2_mbus_framefmt *mf = &format->format; > + int ret; > + > + if (format->pad != 0) > + return -EINVAL; > + > + if (format->format.width != 720 || > + (format->format.height != 480 && format->format.height != 576)) > + return -EINVAL; > + > + if (format->format.code != MEDIA_BUS_FMT_YUYV8_2X8) > + return -EINVAL; > + > + mf->width = format->format.width; > + mf->height = format->format.height; > + mf->code = format->format.code; > + mf->field = V4L2_FIELD_INTERLACED; > + mf->colorspace = 0; > + > + if (format->which != V4L2_SUBDEV_FORMAT_TRY) { Since you don't depend on VIDEO_V4L2_SUBDEV_API you might want to have a look at how other drivers handle FORMAT_TRY when V4L2_SUBDEV_API is not enabled. I know, it's not great :) > + ret = isl7998x_update_std(isl7998x); > + if (ret) > + return ret; > + mf->width = isl7998x->width; > + mf->height = isl7998x->height; > + isl7998x->fmt = &isl7998x_colour_fmts[0]; > + } > + > + return 0; > +} > + > +static int isl7998x_set_test_pattern(struct isl7998x *isl7998x) > +{ > + const struct reg_sequence isl7998x_init_seq_tpg_off[] = { > + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0 } > + }; > + const struct reg_sequence isl7998x_init_seq_tpg_on[] = { > + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, > + isl7998x->test_pattern_bars << 6 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, > + isl7998x->test_pattern_enabled == 1 ? BIT(2) : 0 }, > + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, > + (isl7998x->test_pattern_chans << 4) | > + (isl7998x->test_pattern_color << 2) } > + }; > + struct regmap *regmap = isl7998x->regmap; > + > + if (isl7998x->test_pattern_enabled) { > + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_on, > + ARRAY_SIZE(isl7998x_init_seq_tpg_on)); > + } else { > + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_off, > + ARRAY_SIZE(isl7998x_init_seq_tpg_off)); > + } > +} > + > +static int isl7998x_set_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct isl7998x *isl7998x = container_of(ctrl->handler, > + struct isl7998x, ctrl_handler); > + > + switch (ctrl->id) { > + case V4L2_CID_TEST_PATTERN_BARS: > + isl7998x->test_pattern_bars = ctrl->val & 0x3; > + return isl7998x_set_test_pattern(isl7998x); > + case V4L2_CID_TEST_PATTERN_CHANNELS: > + isl7998x->test_pattern_chans = ctrl->val & 0xf; > + return isl7998x_set_test_pattern(isl7998x); > + case V4L2_CID_TEST_PATTERN_COLOR: > + isl7998x->test_pattern_color = ctrl->val & 0x3; > + return isl7998x_set_test_pattern(isl7998x); > + case V4L2_CID_TEST_PATTERN: > + isl7998x->test_pattern_enabled = !!ctrl->val; > + return isl7998x_set_test_pattern(isl7998x); > + } > + > + return 0; > +} > + > +static int isl7998x_get_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct isl7998x *isl7998x = container_of(ctrl->handler, > + struct isl7998x, ctrl_handler); > + > + v4l2_info(&isl7998x->subdev, "ctrl(id:0x%x,val:0x%x) is not handled\n", > + ctrl->id, ctrl->val); > + > + return 0; > +} > + > +static const struct v4l2_subdev_video_ops isl7998x_subdev_video_ops = { > + .g_mbus_config = isl7998x_g_mbus_config, > + .s_stream = isl7998x_s_stream, > +}; > + > +static const struct v4l2_subdev_pad_ops isl7998x_subdev_pad_ops = { > + .enum_mbus_code = isl7998x_enum_mbus_code, Given the limited number of sizes you support, would you consider adding .enum_frame_size support? > + .get_fmt = isl7998x_get_fmt, > + .set_fmt = isl7998x_set_fmt, > +}; > + > +static const struct v4l2_subdev_ops isl7998x_subdev_ops = { > + .video = &isl7998x_subdev_video_ops, > + .pad = &isl7998x_subdev_pad_ops, > +}; > + > +static const struct media_entity_operations isl7998x_entity_ops = { > + .link_validate = v4l2_subdev_link_validate, > +}; > + > +static const struct v4l2_ctrl_ops isl7998x_ctrl_ops = { > + .s_ctrl = isl7998x_set_ctrl, > + .g_volatile_ctrl = isl7998x_get_ctrl, > +}; > + > +static const char * const isl7998x_test_pattern_bars[] = { > + "bbbbwb", "bbbwwb", "bbwbwb", "bbwwwb" > +}; > + > +static const char * const isl7998x_test_pattern_colors[] = { > + "Yellow", "Blue", "Green", "Pink" > +}; > + > +static const struct v4l2_ctrl_config isl7998x_ctrls[] = { > + { > + .ops = &isl7998x_ctrl_ops, > + .id = V4L2_CID_TEST_PATTERN_BARS, > + .type = V4L2_CTRL_TYPE_MENU, > + .name = "Test Pattern Bars", > + .max = ARRAY_SIZE(isl7998x_test_pattern_bars) - 1, > + .def = 0, > + .qmenu = isl7998x_test_pattern_bars, > + }, { > + .ops = &isl7998x_ctrl_ops, > + .id = V4L2_CID_TEST_PATTERN_CHANNELS, > + .type = V4L2_CTRL_TYPE_INTEGER, > + .name = "Test Pattern Channels", > + .min = 0, > + .max = 0xf, > + .step = 1, > + .def = 0, > + .flags = 0, > + }, { > + .ops = &isl7998x_ctrl_ops, > + .id = V4L2_CID_TEST_PATTERN_COLOR, > + .type = V4L2_CTRL_TYPE_MENU, > + .name = "Test Pattern Color", > + .max = ARRAY_SIZE(isl7998x_test_pattern_colors) - 1, > + .def = 0, > + .qmenu = isl7998x_test_pattern_colors, > + }, > +}; > + > +#define ISL7998x_REG_DECODER_ACA_READABLE_RANGE(page) \ > + /* Decoder range */ \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ > + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ > + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ > + ISL7998x_REG_Px_DEC_HUE(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ > + ISL7998x_REG_Px_DEC_CORING(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > + ISL7998x_REG_Px_DEC_SDTR(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ > + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ > + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ > + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ > + /* ACA range */ \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ > + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ > + ISL7998x_REG_Px_ACA_CTL_4(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ > + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ > + ISL7998x_REG_Px_DEC_PAGE(page)) > + > +#define ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(page) \ > + /* Decoder range */ \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ > + ISL7998x_REG_Px_DEC_INPUT_FMT(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page), \ > + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ > + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ > + ISL7998x_REG_Px_DEC_HUE(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ > + ISL7998x_REG_Px_DEC_CORING(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > + ISL7998x_REG_Px_DEC_SDTR(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ > + ISL7998x_REG_Px_DEC_MISC3(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMD(page), \ > + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ > + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ > + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ > + /* ACA range */ \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ > + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_2(page), \ > + ISL7998x_REG_Px_ACA_CTL_4(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ > + ISL7998x_REG_Px_ACA_HIST_DATA_LO(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page), \ > + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ > + ISL7998x_REG_Px_DEC_PAGE(page)) > + > +#define ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(page) \ > + /* Decoder range */ \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_STATUS_1(page), \ > + ISL7998x_REG_Px_DEC_STATUS_1(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > + ISL7998x_REG_Px_DEC_SDT(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_MVSN(page), \ > + ISL7998x_REG_Px_DEC_HFREF(page)), \ > + /* ACA range */ \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ > + ISL7998x_REG_Px_ACA_Y_HIGH(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_HIST_DATA_LO(page), \ > + ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(page)) > + > +static const struct regmap_range isl7998x_readable_ranges[] = { > + regmap_reg_range(ISL7998x_REG_P0_PRODUCT_ID_CODE, > + ISL7998x_REG_P0_IRQ_SYNC_CTL), > + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, > + ISL7998x_REG_P0_CLOCK_DELAY), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), > + ISL7998x_REG_Px_DEC_PAGE(0)), > + > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(1), > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(2), > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(3), > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(4), > + > + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, > + ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL), > + regmap_reg_range(ISL7998x_REG_P5_FIFO_THRSH_CNT_1, > + ISL7998x_REG_P5_PLL_ANA), > + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, > + ISL7998x_REG_P5_HIST_LINE_CNT_2), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), > + ISL7998x_REG_Px_DEC_PAGE(5)), > +}; > + > +static const struct regmap_range isl7998x_writeable_ranges[] = { > + regmap_reg_range(ISL7998x_REG_P0_SW_RESET_CTL, > + ISL7998x_REG_P0_IRQ_SYNC_CTL), > + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_IRQ, > + ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN), > + regmap_reg_range(ISL7998x_REG_P0_CLOCK_DELAY, > + ISL7998x_REG_P0_CLOCK_DELAY), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), > + ISL7998x_REG_Px_DEC_PAGE(0)), > + > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(1), > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(2), > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(3), > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(4), > + > + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, > + ISL7998x_REG_P5_ESC_MODE_TIME_CTL), > + regmap_reg_range(ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, > + ISL7998x_REG_P5_PLL_ANA), > + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, > + ISL7998x_REG_P5_HIST_LINE_CNT_2), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), > + ISL7998x_REG_Px_DEC_PAGE(5)), > + > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(0xf), > +}; > + > +static const struct regmap_range isl7998x_volatile_ranges[] = { > + regmap_reg_range(ISL7998x_REG_P0_MPP1_SYNC_CTL, > + ISL7998x_REG_P0_IRQ_SYNC_CTL), > + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, > + ISL7998x_REG_P0_INTERRUPT_STATUS), > + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_STATUS, > + ISL7998x_REG_P0_SHORT_DIAG_STATUS), > + > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(1), > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(2), > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(3), > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(4), > + > + regmap_reg_range(ISL7998x_REG_P5_AUTO_TEST_ERR_DET, > + ISL7998x_REG_P5_PIC_HEIGHT_LOW), > +}; > + > +static const struct regmap_access_table isl7998x_readable_table = { > + .yes_ranges = isl7998x_readable_ranges, > + .n_yes_ranges = ARRAY_SIZE(isl7998x_readable_ranges), > +}; > + > +static const struct regmap_access_table isl7998x_writeable_table = { > + .yes_ranges = isl7998x_writeable_ranges, > + .n_yes_ranges = ARRAY_SIZE(isl7998x_writeable_ranges), > +}; > + > +static const struct regmap_access_table isl7998x_volatile_table = { > + .yes_ranges = isl7998x_volatile_ranges, > + .n_yes_ranges = ARRAY_SIZE(isl7998x_volatile_ranges), > +}; > + > +static const struct regmap_range_cfg isl7998x_ranges[] = { > + { > + .range_min = ISL7998x_REG_Pn_BASE(0), > + .range_max = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), > + .selector_reg = ISL7998x_REG_Px_DEC_PAGE(0), > + .selector_mask = ISL7998x_REG_Px_DEC_PAGE_MASK, > + .window_start = 0, > + .window_len = 256, > + } > +}; > + > +static const struct regmap_config isl7998x_regmap = { > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), > + .ranges = isl7998x_ranges, > + .num_ranges = ARRAY_SIZE(isl7998x_ranges), > + .rd_table = &isl7998x_readable_table, > + .wr_table = &isl7998x_writeable_table, > + .volatile_table = &isl7998x_volatile_table, > + .cache_type = REGCACHE_RBTREE, > +}; regmap's great, but do you really need this, as it seems to me you mostly write initialization tables at s_stream and init time and that's it. > + > +static int isl7998x_probe(struct i2c_client *client, > + const struct i2c_device_id *did) > +{ > + struct device *dev = &client->dev; > + struct v4l2_fwnode_endpoint endpoint; > + struct device_node *ep; > + struct isl7998x *isl7998x; > + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent); > + u32 chip_id; > + int i, ret; > + > + ret = i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA); > + if (!ret) { > + dev_warn(&adapter->dev, > + "I2C-Adapter doesn't support I2C_FUNC_SMBUS_WORD\n"); > + return -EIO; > + } > + > + isl7998x = devm_kzalloc(dev, sizeof(*isl7998x), GFP_KERNEL); > + if (!isl7998x) > + return -ENOMEM; > + > + /* Default to all four inputs active unless specified otherwise. */ > + ret = of_property_read_u32(dev->of_node, "isil,num-inputs", > + &isl7998x->nr_inputs); > + if (ret) > + isl7998x->nr_inputs = 4; > + > + if (isl7998x->nr_inputs != 1 && isl7998x->nr_inputs != 2 && > + isl7998x->nr_inputs != 4) { > + dev_err(dev, "Invalid number of inputs selected in DT\n"); > + return -EINVAL; > + } Depending on the outcome of the discussion on bindings, this might change to a DT parsing routine. > + > + isl7998x->pd_gpio = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); > + if (IS_ERR(isl7998x->pd_gpio)) { > + dev_err(dev, "Failed to retrieve/request PD GPIO: %ld\n", > + PTR_ERR(isl7998x->pd_gpio)); > + return PTR_ERR(isl7998x->pd_gpio); > + } > + > + isl7998x->regmap = devm_regmap_init_i2c(client, &isl7998x_regmap); > + if (IS_ERR(isl7998x->regmap)) { > + ret = PTR_ERR(isl7998x->regmap); > + dev_err(dev, "Failed to allocate register map: %d\n", ret); > + return ret; > + } > + > + ep = of_graph_get_next_endpoint(dev->of_node, NULL); > + if (!ep) { > + dev_err(dev, "Missing endpoint node\n"); > + return -EINVAL; > + } > + > + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &endpoint); > + of_node_put(ep); > + if (ret) { > + dev_err(dev, "Failed to parse endpoint\n"); > + return ret; > + } > + > + if (endpoint.bus_type != V4L2_MBUS_CSI2_DPHY || > + endpoint.bus.mipi_csi2.num_data_lanes == 0 || > + endpoint.bus.mipi_csi2.num_data_lanes > 2) { > + dev_err(dev, "Invalid bus type or number of MIPI lanes\n"); > + return -EINVAL; > + } > + > + isl7998x->nr_mipi_lanes = endpoint.bus.mipi_csi2.num_data_lanes; > + > + v4l2_i2c_subdev_init(&isl7998x->subdev, client, &isl7998x_subdev_ops); > + isl7998x->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; The subdevice has a devnode in userspace, do you want to depend on VIDEO_V4L2_SUBDEV_API to allow userspace to control the subdevice? > + > +#ifdef CONFIG_MEDIA_CONTROLLER > + isl7998x->pad.flags = MEDIA_PAD_FL_SOURCE; Again, depending on the outcome of the bindings discussion, the number and nature of pads could change. > + isl7998x->subdev.entity.ops = &isl7998x_entity_ops; > + isl7998x->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; Is this a sensor? I would have used IF_BRIDGE (or more appropriate ones if you find them) but not sensor. > + ret = media_entity_pads_init(&isl7998x->subdev.entity, 1, > + &isl7998x->pad); > + if (ret < 0) > + return ret; > +#endif > + > + isl7998x->width = ISL7998x_WIDTH; > + isl7998x->height = ISL7998x_HEIGHT; > + isl7998x->fmt = &isl7998x_colour_fmts[0]; > + > + ret = v4l2_ctrl_handler_init(&isl7998x->ctrl_handler, > + 2 + ARRAY_SIZE(isl7998x_ctrls)); > + if (ret) > + return ret; > + > + mutex_init(&isl7998x->ctrl_mutex); > + isl7998x->ctrl_handler.lock = &isl7998x->ctrl_mutex; > + isl7998x->link_freq = v4l2_ctrl_new_int_menu(&isl7998x->ctrl_handler, > + &isl7998x_ctrl_ops, V4L2_CID_LINK_FREQ, > + ARRAY_SIZE(link_freq_menu_items) - 1, > + endpoint.bus.mipi_csi2.num_data_lanes == 2 ? > + 1 : 0, link_freq_menu_items); > + isl7998x->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; > + > + for (i = 0; i < ARRAY_SIZE(isl7998x_ctrls); i++) { > + v4l2_ctrl_new_custom(&isl7998x->ctrl_handler, > + &isl7998x_ctrls[i], NULL); > + } > + > + v4l2_ctrl_new_std_menu_items(&isl7998x->ctrl_handler, > + &isl7998x_ctrl_ops, V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(isl7998x_test_pattern_menu) - 1, > + 0, 0, isl7998x_test_pattern_menu); > + Before registering the handler please check if ctrl_handler.error reports if anything has failed. > + isl7998x->subdev.ctrl_handler = &isl7998x->ctrl_handler; > + > + isl7998x->subdev.dev = dev; v4l2_i2c_subdev_init does this for you. Doesn't hurt though. > + ret = v4l2_async_register_subdev(&isl7998x->subdev); > + if (ret < 0) > + goto err_entity_cleanup; > + > + /* > + * Turn the chip ON and keep it ON, otherwise the camera standard > + * detection takes about 600 mS every time we do VIDIOC_G_FMT. > + */ ouch. do you need to query the HW at G_FMT time? Can't you cache the lastly applied format and return it without having to keep the chip on? The same for s_fmt, if the device is powered off, cache the format and apply at s_stream time. Is this possible with this device? (Now that I've read the rest of the driver, yes, you cache the format at g_fmt time, but you apply it at s_fmt time. Can this be post-poned to s_stream and let the chip power off? Also, the usage of runtime_pm is encouraged) > + if (isl7998x->pd_gpio) > + gpiod_set_value(isl7998x->pd_gpio, 0); > + > + ret = regmap_read(isl7998x->regmap, ISL7998x_REG_P0_PRODUCT_ID_CODE, > + &chip_id); > + if (ret) { > + dev_err(dev, "Failed to read ID register: %d\n", ret); > + goto err_init_cleanup; > + } > + > + dev_info(dev, "ISL7998x found (id=%x)\n", chip_id); > + > + ret = isl7998x_init(isl7998x); > + if (ret) > + goto err_init_cleanup; > + > + ret = isl7998x_update_std(isl7998x); > + if (ret) > + goto err_init_cleanup; > + > + return 0; > + > +err_init_cleanup: > + if (isl7998x->pd_gpio) > + gpiod_set_value(isl7998x->pd_gpio, 1); > +err_entity_cleanup: > +#ifdef CONFIG_MEDIA_CONTROLLER media_entity_cleanup() is already protected and resolve to a nop if CONFIG_MEDIA_CONTROLLER is not defined. > + media_entity_cleanup(&isl7998x->subdev.entity); > +#endif Empty line before return is always nice to have :) > + return ret; > +} > + > +static int isl7998x_remove(struct i2c_client *client) > +{ > + struct isl7998x *isl7998x = i2c_to_isl7998x(client); > + > + if (isl7998x->pd_gpio) > + gpiod_set_value(isl7998x->pd_gpio, 1); > + v4l2_async_unregister_subdev(&isl7998x->subdev); > + v4l2_ctrl_handler_free(isl7998x->subdev.ctrl_handler); > + media_entity_cleanup(&isl7998x->subdev.entity); > + > + return 0; > +} > + > +static const struct of_device_id isl7998x_of_match[] = { > + { .compatible = "isil,isl79987", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, isl7998x_of_match); > + > +static const struct i2c_device_id isl7998x_id[] = { > + { "isl79987", 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, isl7998x_id); > + > +static struct i2c_driver isl7998x_i2c_driver = { > + .driver = { > + .name = "isl7998x", > + .of_match_table = of_match_ptr(isl7998x_of_match), > + }, > + .probe = isl7998x_probe, As you don't you use the second argument of the probe function, you can use .probe_new and drop the i2c_device_id table from the driver. > + .remove = isl7998x_remove, > + .id_table = isl7998x_id, > +}; > + > +module_i2c_driver(isl7998x_i2c_driver); > + > +MODULE_DESCRIPTION("Intersil ISL7998x BT656-to-MIPI-CSI2 driver"); > +MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); > +MODULE_LICENSE("GPL"); This doesn't match the SPDX header. Again, sorry for the late review! Cheers j > -- > 2.20.1 > > [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x 2019-07-01 7:58 ` Jacopo Mondi @ 2019-08-06 14:03 ` Marek Vasut 2019-08-12 15:39 ` Jacopo Mondi 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2019-08-06 14:03 UTC (permalink / raw) To: Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring On 7/1/19 9:58 AM, Jacopo Mondi wrote: [...] >> +#define ISL7998x_REG_P5_H_LINE_CNT_1 ISL7998x_REG(5, 0x3a) >> +#define ISL7998x_REG_P5_H_LINE_CNT_2 ISL7998x_REG(5, 0x3b) >> +#define ISL7998x_REG_P5_HIST_LINE_CNT_1 ISL7998x_REG(5, 0x3c) >> +#define ISL7998x_REG_P5_HIST_LINE_CNT_2 ISL7998x_REG(5, 0x3d) > > Not all the above definitions are used. While it doesn't hurt to have > them here, it's a pretty scary list of registers entries. I guess it's good to have a full list of registers available ? >> +static const struct reg_sequence isl7998x_init_seq_1[] = { >> + { ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN, 0xff }, >> + { ISL7998x_REG_Px_DEC_SDT(0x1), 0x07 }, >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x1), 0x03 }, >> + { ISL7998x_REG_Px_DEC_SDT(0x2), 0x07 }, >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x2), 0x03 }, >> + { ISL7998x_REG_Px_DEC_SDT(0x3), 0x07 }, >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x3), 0x03 }, >> + { ISL7998x_REG_Px_DEC_SDT(0x4), 0x07 }, >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x4), 0x03 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x00 }, >> + { ISL7998x_REG_P0_SW_RESET_CTL, 0x1f, 10 }, >> + { ISL7998x_REG_P0_IO_BUFFER_CTL, 0x00 }, >> + { ISL7998x_REG_P0_MPP2_SYNC_CTL, 0xc9 }, >> + { ISL7998x_REG_P0_IRQ_SYNC_CTL, 0xc9 }, >> + { ISL7998x_REG_P0_CHAN_1_IRQ, 0x03 }, >> + { ISL7998x_REG_P0_CHAN_2_IRQ, 0x00 }, >> + { ISL7998x_REG_P0_CHAN_3_IRQ, 0x00 }, >> + { ISL7998x_REG_P0_CHAN_4_IRQ, 0x00 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x02 }, >> + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, 0x85 }, >> + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, 0xa0 }, >> + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x18 }, >> + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x40 }, >> + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x40 }, >> + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, >> + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, >> + { ISL7998x_REG_P5_TP_GEN_MIPI, 0x00 }, >> + { ISL7998x_REG_P5_ESC_MODE_TIME_CTL, 0x0c }, >> + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x00 }, >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x19 }, >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_1, 0x18 }, >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_2, 0xf1 }, >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_3, 0x00 }, >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_4, 0xf1 }, >> + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1, 0x00 }, >> + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2, 0x00 }, >> + { ISL7998x_REG_P5_MIPI_ANA_CLK_CTL, 0x00 }, >> + { ISL7998x_REG_P5_PLL_ANA_STATUS, 0xc0 }, >> + { ISL7998x_REG_P5_PLL_ANA_MISC_CTL, 0x18 }, >> + { ISL7998x_REG_P5_PLL_ANA, 0x00 }, >> + { ISL7998x_REG_P0_SW_RESET_CTL, 0x10, 10 }, >> + /* Page 0xf means write to all of pages 1,2,3,4 */ >> + { ISL7998x_REG_Px_DEC_VDELAY_LO(0xf), 0x14 }, >> + { ISL7998x_REG_Px_DEC_MISC3(0xf), 0xe6 }, >> + { ISL7998x_REG_Px_DEC_CLMD(0xf), 0x85 }, >> + { ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(0xf), 0x11 }, >> + { ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), 0x00 }, >> + { ISL7998x_REG_P0_CLK_CTL_1, 0x1f }, >> + { ISL7998x_REG_P0_CLK_CTL_2, 0x43 }, >> + { ISL7998x_REG_P0_CLK_CTL_3, 0x4f }, >> +}; >> + >> +static const struct reg_sequence isl7998x_init_seq_2[] = { > > Is seq_2 alternative to the first? No, it's second part of the register init sequence . > Care to comment a bit what these > do, if we have to live with register writes sequences? Preinit the chip with sane settings. It's a combination of various register init sequences from various ISL7998x driver mutations. It's like many other camera drivers -- preload a blob of register writes to init the chip into some sane defaults which work well. >> + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x10 }, >> + { ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT, 0xe4 }, >> + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x00 }, >> + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x60 }, >> + { ISL7998x_REG_P5_MIPI_READ_START_CTL, 0x2b }, >> + { ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL, 0x02 }, >> + { ISL7998x_REG_P5_ONE_FIELD_MODE_CTL, 0x00 }, >> + { ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR, 0x62 }, >> + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, 0x02 }, >> + { ISL7998x_REG_P5_MIPI_PCNT_PSFRM, 0x36 }, >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0x00 }, >> + { ISL7998x_REG_P5_MIPI_VBLANK_PSFRM, 0x6c }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0x00 }, >> + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, >> + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1, 0x77 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2, 0x17 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3, 0x08 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4, 0x38 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5, 0x14 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6, 0xf6 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1, 0x00 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD, 0x17 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD, 0x0a }, >> + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2, 0x71 }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7, 0x7a }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8, 0x0f }, >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9, 0x8c }, >> + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x08 }, >> + { ISL7998x_REG_P5_FIFO_THRSH_CNT_1, 0x01 }, >> + { ISL7998x_REG_P5_FIFO_THRSH_CNT_2, 0x0e }, >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x00 }, >> + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, 0x03 }, >> + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2, 0xc0 }, >> + { ISL7998x_REG_P5_H_LINE_CNT_1, 0x06 }, >> + { ISL7998x_REG_P5_H_LINE_CNT_2, 0xb3 }, >> + { ISL7998x_REG_P5_HIST_LINE_CNT_1, 0x00 }, >> + { ISL7998x_REG_P5_HIST_LINE_CNT_2, 0xf1 }, >> + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x00 }, >> + { ISL7998x_REG_P5_MIPI_ANA, 0x00 }, >> + /* >> + * Wait a bit after reset so that the chip can capture a frame >> + * and update internal line counters. >> + */ >> + { ISL7998x_REG_P0_SW_RESET_CTL, 0x00, 50 }, >> +}; >> + >> +struct isl7998x_datafmt { >> + u32 code; >> + enum v4l2_colorspace colorspace; >> +}; >> + >> +static const struct isl7998x_datafmt isl7998x_colour_fmts[] = { >> + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_SRGB }, > > You set the colorspace to 0 in s/g_fmt, while you could simply > hardcode SRGB if you know that's the one the chip provides (which > seems reasonable). Presumably we can have S_FMT switch between these two ? >> +}; >> + >> +/* Menu items for LINK_FREQ V4L2 control */ >> +static const s64 link_freq_menu_items[] = { >> + 108000000, 216000000, 432000000 >> +}; >> + >> +/* Menu items for TEST_PATTERN V4L2 control */ >> +static const char * const isl7998x_test_pattern_menu[] = { >> + "Disabled", "Enabled-PAL (720x576)", "Enabled-NTSC (720x480)" >> +}; >> + >> +struct isl7998x { >> + struct v4l2_subdev subdev; >> + struct regmap *regmap; >> + struct gpio_desc *pd_gpio; >> + unsigned int nr_mipi_lanes; >> + u32 nr_inputs; >> + >> + unsigned int width; >> + unsigned int height; >> + const struct isl7998x_datafmt *fmt; >> +#ifdef CONFIG_MEDIA_CONTROLLER >> + struct media_pad pad; >> +#endif >> + >> + struct v4l2_ctrl_handler ctrl_handler; >> + struct mutex ctrl_mutex; > > it's common practice to state what a mutex protect if it's part of the > device structure. Care to do so? I had a look into drivers/media and it seems the common practice is to state nothing (according to git grep). It's a mutex for the ctrl_handler . >> + /* V4L2 Controls */ >> + struct v4l2_ctrl *link_freq; >> + u8 test_pattern_enabled; >> + u8 test_pattern_bars; >> + u8 test_pattern_chans; >> + u8 test_pattern_color; >> +}; >> + >> +static struct isl7998x *sd_to_isl7998x(struct v4l2_subdev *sd) >> +{ >> + return container_of(sd, struct isl7998x, subdev); >> +} >> + >> +static struct isl7998x *i2c_to_isl7998x(const struct i2c_client *client) >> +{ >> + return sd_to_isl7998x(i2c_get_clientdata(client)); >> +} >> + >> +static int isl7998x_init(struct isl7998x *isl7998x) >> +{ >> + const unsigned int lanes = isl7998x->nr_mipi_lanes; >> + const u32 isl7998x_video_in_chan_map[] = { 0x00, 0x11, 0x02, 0x02 }; >> + const struct reg_sequence isl7998x_init_seq_custom[] = { >> + { ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL, >> + isl7998x_video_in_chan_map[isl7998x->nr_inputs - 1] }, >> + { ISL7998x_REG_P0_CLK_CTL_4, (lanes == 1) ? 0x40 : 0x41 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL, (lanes == 1) ? 0x01 : 0x02 }, >> + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, >> + 0x20 | ((isl7998x->width >> 7) & 0x1f) }, >> + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, >> + (isl7998x->width << 1) & 0xff }, >> + }; >> + struct regmap *regmap = isl7998x->regmap; >> + int ret; >> + >> + ret = regmap_register_patch(regmap, isl7998x_init_seq_1, >> + ARRAY_SIZE(isl7998x_init_seq_1)); >> + if (ret) >> + return ret; >> + >> + ret = regmap_register_patch(regmap, isl7998x_init_seq_custom, >> + ARRAY_SIZE(isl7998x_init_seq_custom)); >> + if (ret) >> + return ret; >> + >> + return regmap_register_patch(regmap, isl7998x_init_seq_2, >> + ARRAY_SIZE(isl7998x_init_seq_2)); >> +} >> + >> +static int isl7998x_g_mbus_config(struct v4l2_subdev *sd, >> + struct v4l2_mbus_config *cfg) > > g_mbus_configg (as well as s_mbus_config) is deprecated. Does your > bridge driver -really- need this? What platform is that? Yes, for iMX6 CSI2 driver, this is needed . Is there a replacement ? >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + >> + cfg->type = V4L2_MBUS_CSI2_DPHY; >> + cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; >> + if (isl7998x->nr_mipi_lanes == 1) >> + cfg->flags |= V4L2_MBUS_CSI2_1_LANE; >> + else >> + cfg->flags |= V4L2_MBUS_CSI2_2_LANE; >> + >> + return 0; >> +} >> + >> +static int isl7998x_s_stream(struct v4l2_subdev *sd, int enable) >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + >> + return isl7998x_init(isl7998x); >> +} >> + >> +static int isl7998x_enum_mbus_code(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_mbus_code_enum *code) >> +{ >> + if (code->pad || code->index >= ARRAY_SIZE(isl7998x_colour_fmts)) >> + return -EINVAL; >> + >> + code->code = isl7998x_colour_fmts[code->index].code; >> + return 0; >> +} >> + >> +static const unsigned int isl7998x_std_res[] = { >> + 480, 576, 576, 480, 480, 576, 480, 480 >> +}; >> + >> +static int isl7998x_update_std(struct isl7998x *isl7998x) >> +{ >> + unsigned int height[ISL7998x_INPUTS]; >> + u8 scanning = GENMASK(ISL7998x_INPUTS - 1, 0); >> + unsigned int i; >> + int ret; >> + u32 reg; >> + >> + while (true) { >> + for (i = 0; i < ISL7998x_INPUTS; i++) { > > Cycle on all inputs or just the active ones? All of them , so we would know the chip settled on some settings. >> + ret = regmap_read(isl7998x->regmap, >> + ISL7998x_REG_Px_DEC_SDT(i + 1), ®); >> + if (ret) >> + return ret; >> + >> + /* Detection is still in progress, restart. */ >> + if (reg & ISL7998x_REG_Px_DEC_SDT_DET) { >> + scanning = GENMASK(ISL7998x_INPUTS - 1, 0); >> + break; >> + } >> + >> + scanning &= ~BIT(i); >> + height[i] = isl7998x_std_res[(reg >> 4) & 0x7]; >> + } >> + >> + if (!scanning) >> + break; >> + >> + mdelay(1); > > mm, seems quite an arbitrary value here. Do you have a better > characterization in the manual, and could you use usleep_range() to > help the scheduler to coalesce wake-ups ? It is arbitrary. >> + } >> + >> + /* >> + * According to Renesas FAE, all input cameras must have the >> + * same standard on this chip. >> + */ >> + for (i = 1; i < isl7998x->nr_inputs ; i++) >> + if (height[i - 1] != height[i]) > > What about width? Ah seems like only 720 is accepted. That's correct, thus far anyway. >> + return -EINVAL; >> + >> + isl7998x->height = height[0]; >> + >> + return 0; >> +} >> + >> +static int isl7998x_get_fmt(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *format) >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + struct v4l2_mbus_framefmt *mf = &format->format; >> + >> + if (format->pad != 0) >> + return -EINVAL; >> + >> + if (isl7998x->test_pattern_enabled == 1) { >> + mf->width = 720; >> + mf->height = 576; >> + } else if (isl7998x->test_pattern_enabled == 2) { >> + mf->width = 720; >> + mf->height = 480; >> + } else { >> + mf->width = isl7998x->width; >> + mf->height = isl7998x->height; >> + } >> + >> + mf->code = isl7998x->fmt->code; >> + mf->field = V4L2_FIELD_INTERLACED; >> + mf->colorspace = 0; >> + >> + return 0; >> +} >> + >> +static int isl7998x_set_fmt(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *format) >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + struct v4l2_mbus_framefmt *mf = &format->format; >> + int ret; >> + >> + if (format->pad != 0) >> + return -EINVAL; >> + >> + if (format->format.width != 720 || >> + (format->format.height != 480 && format->format.height != 576)) >> + return -EINVAL; >> + >> + if (format->format.code != MEDIA_BUS_FMT_YUYV8_2X8) >> + return -EINVAL; >> + >> + mf->width = format->format.width; >> + mf->height = format->format.height; >> + mf->code = format->format.code; >> + mf->field = V4L2_FIELD_INTERLACED; >> + mf->colorspace = 0; >> + >> + if (format->which != V4L2_SUBDEV_FORMAT_TRY) { > > Since you don't depend on VIDEO_V4L2_SUBDEV_API you might want to have > a look at how other drivers handle FORMAT_TRY when V4L2_SUBDEV_API is > not enabled. I know, it's not great :) I added the subdev api dependency. >> + ret = isl7998x_update_std(isl7998x); >> + if (ret) >> + return ret; >> + mf->width = isl7998x->width; >> + mf->height = isl7998x->height; >> + isl7998x->fmt = &isl7998x_colour_fmts[0]; >> + } >> + >> + return 0; >> +} >> + >> +static int isl7998x_set_test_pattern(struct isl7998x *isl7998x) >> +{ >> + const struct reg_sequence isl7998x_init_seq_tpg_off[] = { >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0 } >> + }; >> + const struct reg_sequence isl7998x_init_seq_tpg_on[] = { >> + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, >> + isl7998x->test_pattern_bars << 6 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, >> + isl7998x->test_pattern_enabled == 1 ? BIT(2) : 0 }, >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, >> + (isl7998x->test_pattern_chans << 4) | >> + (isl7998x->test_pattern_color << 2) } >> + }; >> + struct regmap *regmap = isl7998x->regmap; >> + >> + if (isl7998x->test_pattern_enabled) { >> + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_on, >> + ARRAY_SIZE(isl7998x_init_seq_tpg_on)); >> + } else { >> + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_off, >> + ARRAY_SIZE(isl7998x_init_seq_tpg_off)); >> + } >> +} >> + >> +static int isl7998x_set_ctrl(struct v4l2_ctrl *ctrl) >> +{ >> + struct isl7998x *isl7998x = container_of(ctrl->handler, >> + struct isl7998x, ctrl_handler); >> + >> + switch (ctrl->id) { >> + case V4L2_CID_TEST_PATTERN_BARS: >> + isl7998x->test_pattern_bars = ctrl->val & 0x3; >> + return isl7998x_set_test_pattern(isl7998x); >> + case V4L2_CID_TEST_PATTERN_CHANNELS: >> + isl7998x->test_pattern_chans = ctrl->val & 0xf; >> + return isl7998x_set_test_pattern(isl7998x); >> + case V4L2_CID_TEST_PATTERN_COLOR: >> + isl7998x->test_pattern_color = ctrl->val & 0x3; >> + return isl7998x_set_test_pattern(isl7998x); >> + case V4L2_CID_TEST_PATTERN: >> + isl7998x->test_pattern_enabled = !!ctrl->val; >> + return isl7998x_set_test_pattern(isl7998x); >> + } >> + >> + return 0; >> +} >> + >> +static int isl7998x_get_ctrl(struct v4l2_ctrl *ctrl) >> +{ >> + struct isl7998x *isl7998x = container_of(ctrl->handler, >> + struct isl7998x, ctrl_handler); >> + >> + v4l2_info(&isl7998x->subdev, "ctrl(id:0x%x,val:0x%x) is not handled\n", >> + ctrl->id, ctrl->val); >> + >> + return 0; >> +} >> + >> +static const struct v4l2_subdev_video_ops isl7998x_subdev_video_ops = { >> + .g_mbus_config = isl7998x_g_mbus_config, >> + .s_stream = isl7998x_s_stream, >> +}; >> + >> +static const struct v4l2_subdev_pad_ops isl7998x_subdev_pad_ops = { >> + .enum_mbus_code = isl7998x_enum_mbus_code, > > Given the limited number of sizes you support, would you consider > adding .enum_frame_size support? OK >> + .get_fmt = isl7998x_get_fmt, >> + .set_fmt = isl7998x_set_fmt, >> +}; >> + >> +static const struct v4l2_subdev_ops isl7998x_subdev_ops = { >> + .video = &isl7998x_subdev_video_ops, >> + .pad = &isl7998x_subdev_pad_ops, >> +}; >> + >> +static const struct media_entity_operations isl7998x_entity_ops = { >> + .link_validate = v4l2_subdev_link_validate, >> +}; >> + >> +static const struct v4l2_ctrl_ops isl7998x_ctrl_ops = { >> + .s_ctrl = isl7998x_set_ctrl, >> + .g_volatile_ctrl = isl7998x_get_ctrl, >> +}; >> + >> +static const char * const isl7998x_test_pattern_bars[] = { >> + "bbbbwb", "bbbwwb", "bbwbwb", "bbwwwb" >> +}; >> + >> +static const char * const isl7998x_test_pattern_colors[] = { >> + "Yellow", "Blue", "Green", "Pink" >> +}; >> + >> +static const struct v4l2_ctrl_config isl7998x_ctrls[] = { >> + { >> + .ops = &isl7998x_ctrl_ops, >> + .id = V4L2_CID_TEST_PATTERN_BARS, >> + .type = V4L2_CTRL_TYPE_MENU, >> + .name = "Test Pattern Bars", >> + .max = ARRAY_SIZE(isl7998x_test_pattern_bars) - 1, >> + .def = 0, >> + .qmenu = isl7998x_test_pattern_bars, >> + }, { >> + .ops = &isl7998x_ctrl_ops, >> + .id = V4L2_CID_TEST_PATTERN_CHANNELS, >> + .type = V4L2_CTRL_TYPE_INTEGER, >> + .name = "Test Pattern Channels", >> + .min = 0, >> + .max = 0xf, >> + .step = 1, >> + .def = 0, >> + .flags = 0, >> + }, { >> + .ops = &isl7998x_ctrl_ops, >> + .id = V4L2_CID_TEST_PATTERN_COLOR, >> + .type = V4L2_CTRL_TYPE_MENU, >> + .name = "Test Pattern Color", >> + .max = ARRAY_SIZE(isl7998x_test_pattern_colors) - 1, >> + .def = 0, >> + .qmenu = isl7998x_test_pattern_colors, >> + }, >> +}; >> + >> +#define ISL7998x_REG_DECODER_ACA_READABLE_RANGE(page) \ >> + /* Decoder range */ \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ >> + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ >> + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ >> + ISL7998x_REG_Px_DEC_HUE(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ >> + ISL7998x_REG_Px_DEC_CORING(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ >> + ISL7998x_REG_Px_DEC_SDTR(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ >> + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ >> + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ >> + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ >> + /* ACA range */ \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ >> + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ >> + ISL7998x_REG_Px_ACA_CTL_4(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ >> + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ >> + ISL7998x_REG_Px_DEC_PAGE(page)) >> + >> +#define ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(page) \ >> + /* Decoder range */ \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ >> + ISL7998x_REG_Px_DEC_INPUT_FMT(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page), \ >> + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ >> + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ >> + ISL7998x_REG_Px_DEC_HUE(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ >> + ISL7998x_REG_Px_DEC_CORING(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ >> + ISL7998x_REG_Px_DEC_SDTR(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ >> + ISL7998x_REG_Px_DEC_MISC3(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMD(page), \ >> + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ >> + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ >> + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ >> + /* ACA range */ \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ >> + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_2(page), \ >> + ISL7998x_REG_Px_ACA_CTL_4(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ >> + ISL7998x_REG_Px_ACA_HIST_DATA_LO(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page), \ >> + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ >> + ISL7998x_REG_Px_DEC_PAGE(page)) >> + >> +#define ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(page) \ >> + /* Decoder range */ \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_STATUS_1(page), \ >> + ISL7998x_REG_Px_DEC_STATUS_1(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ >> + ISL7998x_REG_Px_DEC_SDT(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_DEC_MVSN(page), \ >> + ISL7998x_REG_Px_DEC_HFREF(page)), \ >> + /* ACA range */ \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ >> + ISL7998x_REG_Px_ACA_Y_HIGH(page)), \ >> + regmap_reg_range(ISL7998x_REG_Px_ACA_HIST_DATA_LO(page), \ >> + ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(page)) >> + >> +static const struct regmap_range isl7998x_readable_ranges[] = { >> + regmap_reg_range(ISL7998x_REG_P0_PRODUCT_ID_CODE, >> + ISL7998x_REG_P0_IRQ_SYNC_CTL), >> + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, >> + ISL7998x_REG_P0_CLOCK_DELAY), >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), >> + ISL7998x_REG_Px_DEC_PAGE(0)), >> + >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(1), >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(2), >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(3), >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(4), >> + >> + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, >> + ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL), >> + regmap_reg_range(ISL7998x_REG_P5_FIFO_THRSH_CNT_1, >> + ISL7998x_REG_P5_PLL_ANA), >> + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, >> + ISL7998x_REG_P5_HIST_LINE_CNT_2), >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), >> + ISL7998x_REG_Px_DEC_PAGE(5)), >> +}; >> + >> +static const struct regmap_range isl7998x_writeable_ranges[] = { >> + regmap_reg_range(ISL7998x_REG_P0_SW_RESET_CTL, >> + ISL7998x_REG_P0_IRQ_SYNC_CTL), >> + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_IRQ, >> + ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN), >> + regmap_reg_range(ISL7998x_REG_P0_CLOCK_DELAY, >> + ISL7998x_REG_P0_CLOCK_DELAY), >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), >> + ISL7998x_REG_Px_DEC_PAGE(0)), >> + >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(1), >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(2), >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(3), >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(4), >> + >> + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, >> + ISL7998x_REG_P5_ESC_MODE_TIME_CTL), >> + regmap_reg_range(ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, >> + ISL7998x_REG_P5_PLL_ANA), >> + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, >> + ISL7998x_REG_P5_HIST_LINE_CNT_2), >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), >> + ISL7998x_REG_Px_DEC_PAGE(5)), >> + >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(0xf), >> +}; >> + >> +static const struct regmap_range isl7998x_volatile_ranges[] = { >> + regmap_reg_range(ISL7998x_REG_P0_MPP1_SYNC_CTL, >> + ISL7998x_REG_P0_IRQ_SYNC_CTL), >> + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, >> + ISL7998x_REG_P0_INTERRUPT_STATUS), >> + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_STATUS, >> + ISL7998x_REG_P0_SHORT_DIAG_STATUS), >> + >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(1), >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(2), >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(3), >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(4), >> + >> + regmap_reg_range(ISL7998x_REG_P5_AUTO_TEST_ERR_DET, >> + ISL7998x_REG_P5_PIC_HEIGHT_LOW), >> +}; >> + >> +static const struct regmap_access_table isl7998x_readable_table = { >> + .yes_ranges = isl7998x_readable_ranges, >> + .n_yes_ranges = ARRAY_SIZE(isl7998x_readable_ranges), >> +}; >> + >> +static const struct regmap_access_table isl7998x_writeable_table = { >> + .yes_ranges = isl7998x_writeable_ranges, >> + .n_yes_ranges = ARRAY_SIZE(isl7998x_writeable_ranges), >> +}; >> + >> +static const struct regmap_access_table isl7998x_volatile_table = { >> + .yes_ranges = isl7998x_volatile_ranges, >> + .n_yes_ranges = ARRAY_SIZE(isl7998x_volatile_ranges), >> +}; >> + >> +static const struct regmap_range_cfg isl7998x_ranges[] = { >> + { >> + .range_min = ISL7998x_REG_Pn_BASE(0), >> + .range_max = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), >> + .selector_reg = ISL7998x_REG_Px_DEC_PAGE(0), >> + .selector_mask = ISL7998x_REG_Px_DEC_PAGE_MASK, >> + .window_start = 0, >> + .window_len = 256, >> + } >> +}; >> + >> +static const struct regmap_config isl7998x_regmap = { >> + .reg_bits = 8, >> + .val_bits = 8, >> + .max_register = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), >> + .ranges = isl7998x_ranges, >> + .num_ranges = ARRAY_SIZE(isl7998x_ranges), >> + .rd_table = &isl7998x_readable_table, >> + .wr_table = &isl7998x_writeable_table, >> + .volatile_table = &isl7998x_volatile_table, >> + .cache_type = REGCACHE_RBTREE, >> +}; > > regmap's great, but do you really need this, as it seems to me you > mostly write initialization tables at s_stream and init time and > that's it. Yes, I need it, the driver is _much_ better and cleaner than it was without regmap. Besides, regmap gives me primitives which will be useful later , for runtime reconfiguration. >> +static int isl7998x_probe(struct i2c_client *client, >> + const struct i2c_device_id *did) >> +{ >> + struct device *dev = &client->dev; >> + struct v4l2_fwnode_endpoint endpoint; >> + struct device_node *ep; >> + struct isl7998x *isl7998x; >> + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent); >> + u32 chip_id; >> + int i, ret; >> + >> + ret = i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA); >> + if (!ret) { >> + dev_warn(&adapter->dev, >> + "I2C-Adapter doesn't support I2C_FUNC_SMBUS_WORD\n"); >> + return -EIO; >> + } >> + >> + isl7998x = devm_kzalloc(dev, sizeof(*isl7998x), GFP_KERNEL); >> + if (!isl7998x) >> + return -ENOMEM; >> + >> + /* Default to all four inputs active unless specified otherwise. */ >> + ret = of_property_read_u32(dev->of_node, "isil,num-inputs", >> + &isl7998x->nr_inputs); >> + if (ret) >> + isl7998x->nr_inputs = 4; >> + >> + if (isl7998x->nr_inputs != 1 && isl7998x->nr_inputs != 2 && >> + isl7998x->nr_inputs != 4) { >> + dev_err(dev, "Invalid number of inputs selected in DT\n"); >> + return -EINVAL; >> + } > > Depending on the outcome of the discussion on bindings, this might > change to a DT parsing routine. > >> + >> + isl7998x->pd_gpio = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); >> + if (IS_ERR(isl7998x->pd_gpio)) { >> + dev_err(dev, "Failed to retrieve/request PD GPIO: %ld\n", >> + PTR_ERR(isl7998x->pd_gpio)); >> + return PTR_ERR(isl7998x->pd_gpio); >> + } >> + >> + isl7998x->regmap = devm_regmap_init_i2c(client, &isl7998x_regmap); >> + if (IS_ERR(isl7998x->regmap)) { >> + ret = PTR_ERR(isl7998x->regmap); >> + dev_err(dev, "Failed to allocate register map: %d\n", ret); >> + return ret; >> + } >> + >> + ep = of_graph_get_next_endpoint(dev->of_node, NULL); >> + if (!ep) { >> + dev_err(dev, "Missing endpoint node\n"); >> + return -EINVAL; >> + } >> + >> + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &endpoint); >> + of_node_put(ep); >> + if (ret) { >> + dev_err(dev, "Failed to parse endpoint\n"); >> + return ret; >> + } >> + >> + if (endpoint.bus_type != V4L2_MBUS_CSI2_DPHY || >> + endpoint.bus.mipi_csi2.num_data_lanes == 0 || >> + endpoint.bus.mipi_csi2.num_data_lanes > 2) { >> + dev_err(dev, "Invalid bus type or number of MIPI lanes\n"); >> + return -EINVAL; >> + } >> + >> + isl7998x->nr_mipi_lanes = endpoint.bus.mipi_csi2.num_data_lanes; >> + >> + v4l2_i2c_subdev_init(&isl7998x->subdev, client, &isl7998x_subdev_ops); >> + isl7998x->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > > The subdevice has a devnode in userspace, do you want to depend on > VIDEO_V4L2_SUBDEV_API to allow userspace to control the subdevice? Yes >> + >> +#ifdef CONFIG_MEDIA_CONTROLLER >> + isl7998x->pad.flags = MEDIA_PAD_FL_SOURCE; > > Again, depending on the outcome of the bindings discussion, the number > and nature of pads could change. > >> + isl7998x->subdev.entity.ops = &isl7998x_entity_ops; >> + isl7998x->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; > > Is this a sensor? I would have used IF_BRIDGE (or more appropriate > ones if you find them) but not sensor. Well, is this a bridge ? Between what ? >> + ret = media_entity_pads_init(&isl7998x->subdev.entity, 1, >> + &isl7998x->pad); >> + if (ret < 0) >> + return ret; >> +#endif >> + >> + isl7998x->width = ISL7998x_WIDTH; >> + isl7998x->height = ISL7998x_HEIGHT; >> + isl7998x->fmt = &isl7998x_colour_fmts[0]; >> + >> + ret = v4l2_ctrl_handler_init(&isl7998x->ctrl_handler, >> + 2 + ARRAY_SIZE(isl7998x_ctrls)); >> + if (ret) >> + return ret; >> + >> + mutex_init(&isl7998x->ctrl_mutex); >> + isl7998x->ctrl_handler.lock = &isl7998x->ctrl_mutex; >> + isl7998x->link_freq = v4l2_ctrl_new_int_menu(&isl7998x->ctrl_handler, >> + &isl7998x_ctrl_ops, V4L2_CID_LINK_FREQ, >> + ARRAY_SIZE(link_freq_menu_items) - 1, >> + endpoint.bus.mipi_csi2.num_data_lanes == 2 ? >> + 1 : 0, link_freq_menu_items); >> + isl7998x->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; >> + >> + for (i = 0; i < ARRAY_SIZE(isl7998x_ctrls); i++) { >> + v4l2_ctrl_new_custom(&isl7998x->ctrl_handler, >> + &isl7998x_ctrls[i], NULL); >> + } >> + >> + v4l2_ctrl_new_std_menu_items(&isl7998x->ctrl_handler, >> + &isl7998x_ctrl_ops, V4L2_CID_TEST_PATTERN, >> + ARRAY_SIZE(isl7998x_test_pattern_menu) - 1, >> + 0, 0, isl7998x_test_pattern_menu); >> + > > Before registering the handler please check if ctrl_handler.error > reports if anything has failed. Eh ? v4l2_ctrl_new_*() will set the ctrl_handler.error ? That's weird, shouldn't it just return an error value then ? >> + isl7998x->subdev.ctrl_handler = &isl7998x->ctrl_handler; >> + >> + isl7998x->subdev.dev = dev; > > v4l2_i2c_subdev_init does this for you. Doesn't hurt though. > >> + ret = v4l2_async_register_subdev(&isl7998x->subdev); >> + if (ret < 0) >> + goto err_entity_cleanup; >> + >> + /* >> + * Turn the chip ON and keep it ON, otherwise the camera standard >> + * detection takes about 600 mS every time we do VIDIOC_G_FMT. >> + */ > > ouch. do you need to query the HW at G_FMT time? Can't you cache the > lastly applied format and return it without having to keep the chip > on? The same for s_fmt, if the device is powered off, cache the format > and apply at s_stream time. Is this possible with this device? Ideally, I would be able to switch the connected cameras at runtime and then re-detect the standard. But I don't think the media framework has any way to implement this and avoid the delay. [...] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x 2019-08-06 14:03 ` Marek Vasut @ 2019-08-12 15:39 ` Jacopo Mondi 0 siblings, 0 replies; 22+ messages in thread From: Jacopo Mondi @ 2019-08-12 15:39 UTC (permalink / raw) To: Marek Vasut; +Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring [-- Attachment #1: Type: text/plain, Size: 34770 bytes --] Hi On Tue, Aug 06, 2019 at 04:03:56PM +0200, Marek Vasut wrote: > On 7/1/19 9:58 AM, Jacopo Mondi wrote: > > [...] > > >> +#define ISL7998x_REG_P5_H_LINE_CNT_1 ISL7998x_REG(5, 0x3a) > >> +#define ISL7998x_REG_P5_H_LINE_CNT_2 ISL7998x_REG(5, 0x3b) > >> +#define ISL7998x_REG_P5_HIST_LINE_CNT_1 ISL7998x_REG(5, 0x3c) > >> +#define ISL7998x_REG_P5_HIST_LINE_CNT_2 ISL7998x_REG(5, 0x3d) > > > > Not all the above definitions are used. While it doesn't hurt to have > > them here, it's a pretty scary list of registers entries. > > I guess it's good to have a full list of registers available ? > I guess it's better to have what is used the actual code, but this does not hurt > >> +static const struct reg_sequence isl7998x_init_seq_1[] = { > >> + { ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN, 0xff }, > >> + { ISL7998x_REG_Px_DEC_SDT(0x1), 0x07 }, > >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x1), 0x03 }, > >> + { ISL7998x_REG_Px_DEC_SDT(0x2), 0x07 }, > >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x2), 0x03 }, > >> + { ISL7998x_REG_Px_DEC_SDT(0x3), 0x07 }, > >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x3), 0x03 }, > >> + { ISL7998x_REG_Px_DEC_SDT(0x4), 0x07 }, > >> + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x4), 0x03 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x00 }, > >> + { ISL7998x_REG_P0_SW_RESET_CTL, 0x1f, 10 }, > >> + { ISL7998x_REG_P0_IO_BUFFER_CTL, 0x00 }, > >> + { ISL7998x_REG_P0_MPP2_SYNC_CTL, 0xc9 }, > >> + { ISL7998x_REG_P0_IRQ_SYNC_CTL, 0xc9 }, > >> + { ISL7998x_REG_P0_CHAN_1_IRQ, 0x03 }, > >> + { ISL7998x_REG_P0_CHAN_2_IRQ, 0x00 }, > >> + { ISL7998x_REG_P0_CHAN_3_IRQ, 0x00 }, > >> + { ISL7998x_REG_P0_CHAN_4_IRQ, 0x00 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x02 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, 0x85 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, 0xa0 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x18 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x40 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x40 }, > >> + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, > >> + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, > >> + { ISL7998x_REG_P5_TP_GEN_MIPI, 0x00 }, > >> + { ISL7998x_REG_P5_ESC_MODE_TIME_CTL, 0x0c }, > >> + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x00 }, > >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, > >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x19 }, > >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_1, 0x18 }, > >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_2, 0xf1 }, > >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_3, 0x00 }, > >> + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_4, 0xf1 }, > >> + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1, 0x00 }, > >> + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2, 0x00 }, > >> + { ISL7998x_REG_P5_MIPI_ANA_CLK_CTL, 0x00 }, > >> + { ISL7998x_REG_P5_PLL_ANA_STATUS, 0xc0 }, > >> + { ISL7998x_REG_P5_PLL_ANA_MISC_CTL, 0x18 }, > >> + { ISL7998x_REG_P5_PLL_ANA, 0x00 }, > >> + { ISL7998x_REG_P0_SW_RESET_CTL, 0x10, 10 }, > >> + /* Page 0xf means write to all of pages 1,2,3,4 */ > >> + { ISL7998x_REG_Px_DEC_VDELAY_LO(0xf), 0x14 }, > >> + { ISL7998x_REG_Px_DEC_MISC3(0xf), 0xe6 }, > >> + { ISL7998x_REG_Px_DEC_CLMD(0xf), 0x85 }, > >> + { ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(0xf), 0x11 }, > >> + { ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), 0x00 }, > >> + { ISL7998x_REG_P0_CLK_CTL_1, 0x1f }, > >> + { ISL7998x_REG_P0_CLK_CTL_2, 0x43 }, > >> + { ISL7998x_REG_P0_CLK_CTL_3, 0x4f }, > >> +}; > >> + > >> +static const struct reg_sequence isl7998x_init_seq_2[] = { > > > > Is seq_2 alternative to the first? > > No, it's second part of the register init sequence . > > > Care to comment a bit what these > > do, if we have to live with register writes sequences? > > Preinit the chip with sane settings. It's a combination of various > register init sequences from various ISL7998x driver mutations. > > It's like many other camera drivers -- preload a blob of register writes > to init the chip into some sane defaults which work well. > Something which is discouraged, even if most of the times un-avoidable, I understand. In the process of writing and testing a driver one usually need to decode part of those information. If you had to do so, noting what a block of register does helps others removing blobs and making the register configurations dynamic eventually. If you don't have such informations no need to decode them just for writing a comment. > >> + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x10 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT, 0xe4 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x00 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x60 }, > >> + { ISL7998x_REG_P5_MIPI_READ_START_CTL, 0x2b }, > >> + { ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL, 0x02 }, > >> + { ISL7998x_REG_P5_ONE_FIELD_MODE_CTL, 0x00 }, > >> + { ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR, 0x62 }, > >> + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, 0x02 }, > >> + { ISL7998x_REG_P5_MIPI_PCNT_PSFRM, 0x36 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0x00 }, > >> + { ISL7998x_REG_P5_MIPI_VBLANK_PSFRM, 0x6c }, > >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0x00 }, > >> + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, > >> + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1, 0x77 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2, 0x17 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3, 0x08 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4, 0x38 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5, 0x14 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6, 0xf6 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1, 0x00 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD, 0x17 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD, 0x0a }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2, 0x71 }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7, 0x7a }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8, 0x0f }, > >> + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9, 0x8c }, > >> + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x08 }, > >> + { ISL7998x_REG_P5_FIFO_THRSH_CNT_1, 0x01 }, > >> + { ISL7998x_REG_P5_FIFO_THRSH_CNT_2, 0x0e }, > >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, > >> + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x00 }, > >> + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, 0x03 }, > >> + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2, 0xc0 }, > >> + { ISL7998x_REG_P5_H_LINE_CNT_1, 0x06 }, > >> + { ISL7998x_REG_P5_H_LINE_CNT_2, 0xb3 }, > >> + { ISL7998x_REG_P5_HIST_LINE_CNT_1, 0x00 }, > >> + { ISL7998x_REG_P5_HIST_LINE_CNT_2, 0xf1 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x00 }, > >> + { ISL7998x_REG_P5_MIPI_ANA, 0x00 }, > >> + /* > >> + * Wait a bit after reset so that the chip can capture a frame > >> + * and update internal line counters. > >> + */ > >> + { ISL7998x_REG_P0_SW_RESET_CTL, 0x00, 50 }, > >> +}; > >> + > >> +struct isl7998x_datafmt { > >> + u32 code; > >> + enum v4l2_colorspace colorspace; > >> +}; > >> + > >> +static const struct isl7998x_datafmt isl7998x_colour_fmts[] = { > >> + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_SRGB }, > > > > You set the colorspace to 0 in s/g_fmt, while you could simply > > hardcode SRGB if you know that's the one the chip provides (which > > seems reasonable). > > Presumably we can have S_FMT switch between these two ? > My point was that in s/g_fmt the colorspace should be set to SRGB > >> +}; > >> + > >> +/* Menu items for LINK_FREQ V4L2 control */ > >> +static const s64 link_freq_menu_items[] = { > >> + 108000000, 216000000, 432000000 > >> +}; > >> + > >> +/* Menu items for TEST_PATTERN V4L2 control */ > >> +static const char * const isl7998x_test_pattern_menu[] = { > >> + "Disabled", "Enabled-PAL (720x576)", "Enabled-NTSC (720x480)" > >> +}; > >> + > >> +struct isl7998x { > >> + struct v4l2_subdev subdev; > >> + struct regmap *regmap; > >> + struct gpio_desc *pd_gpio; > >> + unsigned int nr_mipi_lanes; > >> + u32 nr_inputs; > >> + > >> + unsigned int width; > >> + unsigned int height; > >> + const struct isl7998x_datafmt *fmt; > >> +#ifdef CONFIG_MEDIA_CONTROLLER > >> + struct media_pad pad; > >> +#endif > >> + > >> + struct v4l2_ctrl_handler ctrl_handler; > >> + struct mutex ctrl_mutex; > > > > it's common practice to state what a mutex protect if it's part of the > > device structure. Care to do so? > > I had a look into drivers/media and it seems the common practice is to > state nothing (according to git grep). It's a mutex for the ctrl_handler . > It won't take you long to write it in a comment then. > >> + /* V4L2 Controls */ > >> + struct v4l2_ctrl *link_freq; > >> + u8 test_pattern_enabled; > >> + u8 test_pattern_bars; > >> + u8 test_pattern_chans; > >> + u8 test_pattern_color; > >> +}; > >> + > >> +static struct isl7998x *sd_to_isl7998x(struct v4l2_subdev *sd) > >> +{ > >> + return container_of(sd, struct isl7998x, subdev); > >> +} > >> + > >> +static struct isl7998x *i2c_to_isl7998x(const struct i2c_client *client) > >> +{ > >> + return sd_to_isl7998x(i2c_get_clientdata(client)); > >> +} > >> + > >> +static int isl7998x_init(struct isl7998x *isl7998x) > >> +{ > >> + const unsigned int lanes = isl7998x->nr_mipi_lanes; > >> + const u32 isl7998x_video_in_chan_map[] = { 0x00, 0x11, 0x02, 0x02 }; > >> + const struct reg_sequence isl7998x_init_seq_custom[] = { > >> + { ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL, > >> + isl7998x_video_in_chan_map[isl7998x->nr_inputs - 1] }, > >> + { ISL7998x_REG_P0_CLK_CTL_4, (lanes == 1) ? 0x40 : 0x41 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_CTL, (lanes == 1) ? 0x01 : 0x02 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, > >> + 0x20 | ((isl7998x->width >> 7) & 0x1f) }, > >> + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, > >> + (isl7998x->width << 1) & 0xff }, > >> + }; > >> + struct regmap *regmap = isl7998x->regmap; > >> + int ret; > >> + > >> + ret = regmap_register_patch(regmap, isl7998x_init_seq_1, > >> + ARRAY_SIZE(isl7998x_init_seq_1)); > >> + if (ret) > >> + return ret; > >> + > >> + ret = regmap_register_patch(regmap, isl7998x_init_seq_custom, > >> + ARRAY_SIZE(isl7998x_init_seq_custom)); > >> + if (ret) > >> + return ret; > >> + > >> + return regmap_register_patch(regmap, isl7998x_init_seq_2, > >> + ARRAY_SIZE(isl7998x_init_seq_2)); > >> +} > >> + > >> +static int isl7998x_g_mbus_config(struct v4l2_subdev *sd, > >> + struct v4l2_mbus_config *cfg) > > > > g_mbus_configg (as well as s_mbus_config) is deprecated. Does your > > bridge driver -really- need this? What platform is that? > > Yes, for iMX6 CSI2 driver, this is needed . Is there a replacement ? > I don't see any g_mbus_config call in the imx staging driver. All these information should be parsed from DT. > >> +{ > >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > >> + > >> + cfg->type = V4L2_MBUS_CSI2_DPHY; > >> + cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; > >> + if (isl7998x->nr_mipi_lanes == 1) > >> + cfg->flags |= V4L2_MBUS_CSI2_1_LANE; > >> + else > >> + cfg->flags |= V4L2_MBUS_CSI2_2_LANE; > >> + > >> + return 0; > >> +} > >> + > >> +static int isl7998x_s_stream(struct v4l2_subdev *sd, int enable) > >> +{ > >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > >> + > >> + return isl7998x_init(isl7998x); > >> +} > >> + > >> +static int isl7998x_enum_mbus_code(struct v4l2_subdev *sd, > >> + struct v4l2_subdev_pad_config *cfg, > >> + struct v4l2_subdev_mbus_code_enum *code) > >> +{ > >> + if (code->pad || code->index >= ARRAY_SIZE(isl7998x_colour_fmts)) > >> + return -EINVAL; > >> + > >> + code->code = isl7998x_colour_fmts[code->index].code; > >> + return 0; > >> +} > >> + > >> +static const unsigned int isl7998x_std_res[] = { > >> + 480, 576, 576, 480, 480, 576, 480, 480 > >> +}; > >> + > >> +static int isl7998x_update_std(struct isl7998x *isl7998x) > >> +{ > >> + unsigned int height[ISL7998x_INPUTS]; > >> + u8 scanning = GENMASK(ISL7998x_INPUTS - 1, 0); > >> + unsigned int i; > >> + int ret; > >> + u32 reg; > >> + > >> + while (true) { > >> + for (i = 0; i < ISL7998x_INPUTS; i++) { > > > > Cycle on all inputs or just the active ones? > > All of them , so we would know the chip settled on some settings. > > >> + ret = regmap_read(isl7998x->regmap, > >> + ISL7998x_REG_Px_DEC_SDT(i + 1), ®); > >> + if (ret) > >> + return ret; > >> + > >> + /* Detection is still in progress, restart. */ > >> + if (reg & ISL7998x_REG_Px_DEC_SDT_DET) { > >> + scanning = GENMASK(ISL7998x_INPUTS - 1, 0); > >> + break; > >> + } > >> + > >> + scanning &= ~BIT(i); > >> + height[i] = isl7998x_std_res[(reg >> 4) & 0x7]; > >> + } > >> + > >> + if (!scanning) > >> + break; > >> + > >> + mdelay(1); > > > > mm, seems quite an arbitrary value here. Do you have a better > > characterization in the manual, and could you use usleep_range() to > > help the scheduler to coalesce wake-ups ? > > It is arbitrary. > Please use at least usleep_range() > >> + } > >> + > >> + /* > >> + * According to Renesas FAE, all input cameras must have the > >> + * same standard on this chip. > >> + */ > >> + for (i = 1; i < isl7998x->nr_inputs ; i++) > >> + if (height[i - 1] != height[i]) > > > > What about width? Ah seems like only 720 is accepted. > > That's correct, thus far anyway. > > >> + return -EINVAL; > >> + > >> + isl7998x->height = height[0]; > >> + > >> + return 0; > >> +} > >> + > >> +static int isl7998x_get_fmt(struct v4l2_subdev *sd, > >> + struct v4l2_subdev_pad_config *cfg, > >> + struct v4l2_subdev_format *format) > >> +{ > >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > >> + struct v4l2_mbus_framefmt *mf = &format->format; > >> + > >> + if (format->pad != 0) > >> + return -EINVAL; > >> + > >> + if (isl7998x->test_pattern_enabled == 1) { > >> + mf->width = 720; > >> + mf->height = 576; > >> + } else if (isl7998x->test_pattern_enabled == 2) { > >> + mf->width = 720; > >> + mf->height = 480; > >> + } else { > >> + mf->width = isl7998x->width; > >> + mf->height = isl7998x->height; > >> + } > >> + > >> + mf->code = isl7998x->fmt->code; > >> + mf->field = V4L2_FIELD_INTERLACED; > >> + mf->colorspace = 0; > >> + > >> + return 0; > >> +} > >> + > >> +static int isl7998x_set_fmt(struct v4l2_subdev *sd, > >> + struct v4l2_subdev_pad_config *cfg, > >> + struct v4l2_subdev_format *format) > >> +{ > >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > >> + struct v4l2_mbus_framefmt *mf = &format->format; > >> + int ret; > >> + > >> + if (format->pad != 0) > >> + return -EINVAL; > >> + > >> + if (format->format.width != 720 || > >> + (format->format.height != 480 && format->format.height != 576)) > >> + return -EINVAL; > >> + > >> + if (format->format.code != MEDIA_BUS_FMT_YUYV8_2X8) > >> + return -EINVAL; > >> + > >> + mf->width = format->format.width; > >> + mf->height = format->format.height; > >> + mf->code = format->format.code; > >> + mf->field = V4L2_FIELD_INTERLACED; > >> + mf->colorspace = 0; > >> + > >> + if (format->which != V4L2_SUBDEV_FORMAT_TRY) { > > > > Since you don't depend on VIDEO_V4L2_SUBDEV_API you might want to have > > a look at how other drivers handle FORMAT_TRY when V4L2_SUBDEV_API is > > not enabled. I know, it's not great :) > > I added the subdev api dependency. > > >> + ret = isl7998x_update_std(isl7998x); > >> + if (ret) > >> + return ret; > >> + mf->width = isl7998x->width; > >> + mf->height = isl7998x->height; > >> + isl7998x->fmt = &isl7998x_colour_fmts[0]; > >> + } > >> + > >> + return 0; > >> +} > >> + > >> +static int isl7998x_set_test_pattern(struct isl7998x *isl7998x) > >> +{ > >> + const struct reg_sequence isl7998x_init_seq_tpg_off[] = { > >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0 } > >> + }; > >> + const struct reg_sequence isl7998x_init_seq_tpg_on[] = { > >> + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, > >> + isl7998x->test_pattern_bars << 6 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, > >> + isl7998x->test_pattern_enabled == 1 ? BIT(2) : 0 }, > >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, > >> + (isl7998x->test_pattern_chans << 4) | > >> + (isl7998x->test_pattern_color << 2) } > >> + }; > >> + struct regmap *regmap = isl7998x->regmap; > >> + > >> + if (isl7998x->test_pattern_enabled) { > >> + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_on, > >> + ARRAY_SIZE(isl7998x_init_seq_tpg_on)); > >> + } else { > >> + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_off, > >> + ARRAY_SIZE(isl7998x_init_seq_tpg_off)); > >> + } > >> +} > >> + > >> +static int isl7998x_set_ctrl(struct v4l2_ctrl *ctrl) > >> +{ > >> + struct isl7998x *isl7998x = container_of(ctrl->handler, > >> + struct isl7998x, ctrl_handler); > >> + > >> + switch (ctrl->id) { > >> + case V4L2_CID_TEST_PATTERN_BARS: > >> + isl7998x->test_pattern_bars = ctrl->val & 0x3; > >> + return isl7998x_set_test_pattern(isl7998x); > >> + case V4L2_CID_TEST_PATTERN_CHANNELS: > >> + isl7998x->test_pattern_chans = ctrl->val & 0xf; > >> + return isl7998x_set_test_pattern(isl7998x); > >> + case V4L2_CID_TEST_PATTERN_COLOR: > >> + isl7998x->test_pattern_color = ctrl->val & 0x3; > >> + return isl7998x_set_test_pattern(isl7998x); > >> + case V4L2_CID_TEST_PATTERN: > >> + isl7998x->test_pattern_enabled = !!ctrl->val; > >> + return isl7998x_set_test_pattern(isl7998x); > >> + } > >> + > >> + return 0; > >> +} > >> + > >> +static int isl7998x_get_ctrl(struct v4l2_ctrl *ctrl) > >> +{ > >> + struct isl7998x *isl7998x = container_of(ctrl->handler, > >> + struct isl7998x, ctrl_handler); > >> + > >> + v4l2_info(&isl7998x->subdev, "ctrl(id:0x%x,val:0x%x) is not handled\n", > >> + ctrl->id, ctrl->val); > >> + > >> + return 0; > >> +} > >> + > >> +static const struct v4l2_subdev_video_ops isl7998x_subdev_video_ops = { > >> + .g_mbus_config = isl7998x_g_mbus_config, > >> + .s_stream = isl7998x_s_stream, > >> +}; > >> + > >> +static const struct v4l2_subdev_pad_ops isl7998x_subdev_pad_ops = { > >> + .enum_mbus_code = isl7998x_enum_mbus_code, > > > > Given the limited number of sizes you support, would you consider > > adding .enum_frame_size support? > > OK > > >> + .get_fmt = isl7998x_get_fmt, > >> + .set_fmt = isl7998x_set_fmt, > >> +}; > >> + > >> +static const struct v4l2_subdev_ops isl7998x_subdev_ops = { > >> + .video = &isl7998x_subdev_video_ops, > >> + .pad = &isl7998x_subdev_pad_ops, > >> +}; > >> + > >> +static const struct media_entity_operations isl7998x_entity_ops = { > >> + .link_validate = v4l2_subdev_link_validate, > >> +}; > >> + > >> +static const struct v4l2_ctrl_ops isl7998x_ctrl_ops = { > >> + .s_ctrl = isl7998x_set_ctrl, > >> + .g_volatile_ctrl = isl7998x_get_ctrl, > >> +}; > >> + > >> +static const char * const isl7998x_test_pattern_bars[] = { > >> + "bbbbwb", "bbbwwb", "bbwbwb", "bbwwwb" > >> +}; > >> + > >> +static const char * const isl7998x_test_pattern_colors[] = { > >> + "Yellow", "Blue", "Green", "Pink" > >> +}; > >> + > >> +static const struct v4l2_ctrl_config isl7998x_ctrls[] = { > >> + { > >> + .ops = &isl7998x_ctrl_ops, > >> + .id = V4L2_CID_TEST_PATTERN_BARS, > >> + .type = V4L2_CTRL_TYPE_MENU, > >> + .name = "Test Pattern Bars", > >> + .max = ARRAY_SIZE(isl7998x_test_pattern_bars) - 1, > >> + .def = 0, > >> + .qmenu = isl7998x_test_pattern_bars, > >> + }, { > >> + .ops = &isl7998x_ctrl_ops, > >> + .id = V4L2_CID_TEST_PATTERN_CHANNELS, > >> + .type = V4L2_CTRL_TYPE_INTEGER, > >> + .name = "Test Pattern Channels", > >> + .min = 0, > >> + .max = 0xf, > >> + .step = 1, > >> + .def = 0, > >> + .flags = 0, > >> + }, { > >> + .ops = &isl7998x_ctrl_ops, > >> + .id = V4L2_CID_TEST_PATTERN_COLOR, > >> + .type = V4L2_CTRL_TYPE_MENU, > >> + .name = "Test Pattern Color", > >> + .max = ARRAY_SIZE(isl7998x_test_pattern_colors) - 1, > >> + .def = 0, > >> + .qmenu = isl7998x_test_pattern_colors, > >> + }, > >> +}; > >> + > >> +#define ISL7998x_REG_DECODER_ACA_READABLE_RANGE(page) \ > >> + /* Decoder range */ \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ > >> + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ > >> + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ > >> + ISL7998x_REG_Px_DEC_HUE(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ > >> + ISL7998x_REG_Px_DEC_CORING(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > >> + ISL7998x_REG_Px_DEC_SDTR(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ > >> + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ > >> + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ > >> + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ > >> + /* ACA range */ \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ > >> + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ > >> + ISL7998x_REG_Px_ACA_CTL_4(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ > >> + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ > >> + ISL7998x_REG_Px_DEC_PAGE(page)) > >> + > >> +#define ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(page) \ > >> + /* Decoder range */ \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ > >> + ISL7998x_REG_Px_DEC_INPUT_FMT(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page), \ > >> + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ > >> + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ > >> + ISL7998x_REG_Px_DEC_HUE(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ > >> + ISL7998x_REG_Px_DEC_CORING(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > >> + ISL7998x_REG_Px_DEC_SDTR(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ > >> + ISL7998x_REG_Px_DEC_MISC3(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMD(page), \ > >> + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ > >> + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ > >> + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ > >> + /* ACA range */ \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ > >> + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_2(page), \ > >> + ISL7998x_REG_Px_ACA_CTL_4(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ > >> + ISL7998x_REG_Px_ACA_HIST_DATA_LO(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page), \ > >> + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ > >> + ISL7998x_REG_Px_DEC_PAGE(page)) > >> + > >> +#define ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(page) \ > >> + /* Decoder range */ \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_STATUS_1(page), \ > >> + ISL7998x_REG_Px_DEC_STATUS_1(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > >> + ISL7998x_REG_Px_DEC_SDT(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_MVSN(page), \ > >> + ISL7998x_REG_Px_DEC_HFREF(page)), \ > >> + /* ACA range */ \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ > >> + ISL7998x_REG_Px_ACA_Y_HIGH(page)), \ > >> + regmap_reg_range(ISL7998x_REG_Px_ACA_HIST_DATA_LO(page), \ > >> + ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(page)) > >> + > >> +static const struct regmap_range isl7998x_readable_ranges[] = { > >> + regmap_reg_range(ISL7998x_REG_P0_PRODUCT_ID_CODE, > >> + ISL7998x_REG_P0_IRQ_SYNC_CTL), > >> + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, > >> + ISL7998x_REG_P0_CLOCK_DELAY), > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), > >> + ISL7998x_REG_Px_DEC_PAGE(0)), > >> + > >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(1), > >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(2), > >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(3), > >> + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(4), > >> + > >> + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, > >> + ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL), > >> + regmap_reg_range(ISL7998x_REG_P5_FIFO_THRSH_CNT_1, > >> + ISL7998x_REG_P5_PLL_ANA), > >> + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, > >> + ISL7998x_REG_P5_HIST_LINE_CNT_2), > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), > >> + ISL7998x_REG_Px_DEC_PAGE(5)), > >> +}; > >> + > >> +static const struct regmap_range isl7998x_writeable_ranges[] = { > >> + regmap_reg_range(ISL7998x_REG_P0_SW_RESET_CTL, > >> + ISL7998x_REG_P0_IRQ_SYNC_CTL), > >> + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_IRQ, > >> + ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN), > >> + regmap_reg_range(ISL7998x_REG_P0_CLOCK_DELAY, > >> + ISL7998x_REG_P0_CLOCK_DELAY), > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), > >> + ISL7998x_REG_Px_DEC_PAGE(0)), > >> + > >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(1), > >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(2), > >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(3), > >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(4), > >> + > >> + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, > >> + ISL7998x_REG_P5_ESC_MODE_TIME_CTL), > >> + regmap_reg_range(ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, > >> + ISL7998x_REG_P5_PLL_ANA), > >> + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, > >> + ISL7998x_REG_P5_HIST_LINE_CNT_2), > >> + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), > >> + ISL7998x_REG_Px_DEC_PAGE(5)), > >> + > >> + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(0xf), > >> +}; > >> + > >> +static const struct regmap_range isl7998x_volatile_ranges[] = { > >> + regmap_reg_range(ISL7998x_REG_P0_MPP1_SYNC_CTL, > >> + ISL7998x_REG_P0_IRQ_SYNC_CTL), > >> + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, > >> + ISL7998x_REG_P0_INTERRUPT_STATUS), > >> + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_STATUS, > >> + ISL7998x_REG_P0_SHORT_DIAG_STATUS), > >> + > >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(1), > >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(2), > >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(3), > >> + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(4), > >> + > >> + regmap_reg_range(ISL7998x_REG_P5_AUTO_TEST_ERR_DET, > >> + ISL7998x_REG_P5_PIC_HEIGHT_LOW), > >> +}; > >> + > >> +static const struct regmap_access_table isl7998x_readable_table = { > >> + .yes_ranges = isl7998x_readable_ranges, > >> + .n_yes_ranges = ARRAY_SIZE(isl7998x_readable_ranges), > >> +}; > >> + > >> +static const struct regmap_access_table isl7998x_writeable_table = { > >> + .yes_ranges = isl7998x_writeable_ranges, > >> + .n_yes_ranges = ARRAY_SIZE(isl7998x_writeable_ranges), > >> +}; > >> + > >> +static const struct regmap_access_table isl7998x_volatile_table = { > >> + .yes_ranges = isl7998x_volatile_ranges, > >> + .n_yes_ranges = ARRAY_SIZE(isl7998x_volatile_ranges), > >> +}; > >> + > >> +static const struct regmap_range_cfg isl7998x_ranges[] = { > >> + { > >> + .range_min = ISL7998x_REG_Pn_BASE(0), > >> + .range_max = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), > >> + .selector_reg = ISL7998x_REG_Px_DEC_PAGE(0), > >> + .selector_mask = ISL7998x_REG_Px_DEC_PAGE_MASK, > >> + .window_start = 0, > >> + .window_len = 256, > >> + } > >> +}; > >> + > >> +static const struct regmap_config isl7998x_regmap = { > >> + .reg_bits = 8, > >> + .val_bits = 8, > >> + .max_register = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), > >> + .ranges = isl7998x_ranges, > >> + .num_ranges = ARRAY_SIZE(isl7998x_ranges), > >> + .rd_table = &isl7998x_readable_table, > >> + .wr_table = &isl7998x_writeable_table, > >> + .volatile_table = &isl7998x_volatile_table, Isn't this weirdly indented? > >> + .cache_type = REGCACHE_RBTREE, > >> +}; > > > > regmap's great, but do you really need this, as it seems to me you > > mostly write initialization tables at s_stream and init time and > > that's it. > > Yes, I need it, the driver is _much_ better and cleaner than it was > without regmap. Besides, regmap gives me primitives which will be useful > later , for runtime reconfiguration. > > >> +static int isl7998x_probe(struct i2c_client *client, > >> + const struct i2c_device_id *did) > >> +{ > >> + struct device *dev = &client->dev; > >> + struct v4l2_fwnode_endpoint endpoint; > >> + struct device_node *ep; > >> + struct isl7998x *isl7998x; > >> + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent); > >> + u32 chip_id; > >> + int i, ret; > >> + > >> + ret = i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA); > >> + if (!ret) { > >> + dev_warn(&adapter->dev, > >> + "I2C-Adapter doesn't support I2C_FUNC_SMBUS_WORD\n"); > >> + return -EIO; > >> + } > >> + > >> + isl7998x = devm_kzalloc(dev, sizeof(*isl7998x), GFP_KERNEL); > >> + if (!isl7998x) > >> + return -ENOMEM; > >> + > >> + /* Default to all four inputs active unless specified otherwise. */ > >> + ret = of_property_read_u32(dev->of_node, "isil,num-inputs", > >> + &isl7998x->nr_inputs); > >> + if (ret) > >> + isl7998x->nr_inputs = 4; > >> + > >> + if (isl7998x->nr_inputs != 1 && isl7998x->nr_inputs != 2 && > >> + isl7998x->nr_inputs != 4) { > >> + dev_err(dev, "Invalid number of inputs selected in DT\n"); > >> + return -EINVAL; > >> + } > > > > Depending on the outcome of the discussion on bindings, this might > > change to a DT parsing routine. > > > >> + > >> + isl7998x->pd_gpio = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); > >> + if (IS_ERR(isl7998x->pd_gpio)) { > >> + dev_err(dev, "Failed to retrieve/request PD GPIO: %ld\n", > >> + PTR_ERR(isl7998x->pd_gpio)); > >> + return PTR_ERR(isl7998x->pd_gpio); > >> + } > >> + > >> + isl7998x->regmap = devm_regmap_init_i2c(client, &isl7998x_regmap); > >> + if (IS_ERR(isl7998x->regmap)) { > >> + ret = PTR_ERR(isl7998x->regmap); > >> + dev_err(dev, "Failed to allocate register map: %d\n", ret); > >> + return ret; > >> + } > >> + > >> + ep = of_graph_get_next_endpoint(dev->of_node, NULL); > >> + if (!ep) { > >> + dev_err(dev, "Missing endpoint node\n"); > >> + return -EINVAL; > >> + } > >> + > >> + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &endpoint); > >> + of_node_put(ep); > >> + if (ret) { > >> + dev_err(dev, "Failed to parse endpoint\n"); > >> + return ret; > >> + } > >> + > >> + if (endpoint.bus_type != V4L2_MBUS_CSI2_DPHY || > >> + endpoint.bus.mipi_csi2.num_data_lanes == 0 || > >> + endpoint.bus.mipi_csi2.num_data_lanes > 2) { > >> + dev_err(dev, "Invalid bus type or number of MIPI lanes\n"); > >> + return -EINVAL; > >> + } > >> + > >> + isl7998x->nr_mipi_lanes = endpoint.bus.mipi_csi2.num_data_lanes; > >> + > >> + v4l2_i2c_subdev_init(&isl7998x->subdev, client, &isl7998x_subdev_ops); > >> + isl7998x->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > > > > The subdevice has a devnode in userspace, do you want to depend on > > VIDEO_V4L2_SUBDEV_API to allow userspace to control the subdevice? > > Yes > > >> + > >> +#ifdef CONFIG_MEDIA_CONTROLLER > >> + isl7998x->pad.flags = MEDIA_PAD_FL_SOURCE; > > > > Again, depending on the outcome of the bindings discussion, the number > > and nature of pads could change. > > > >> + isl7998x->subdev.entity.ops = &isl7998x_entity_ops; > >> + isl7998x->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; > > > > Is this a sensor? I would have used IF_BRIDGE (or more appropriate > > ones if you find them) but not sensor. > > Well, is this a bridge ? Between what ? > Between an analogue video source and a video input port on the SoC, parallel or CSI-2. Definitely, it's not a camera sensor. > >> + ret = media_entity_pads_init(&isl7998x->subdev.entity, 1, > >> + &isl7998x->pad); > >> + if (ret < 0) > >> + return ret; > >> +#endif > >> + > >> + isl7998x->width = ISL7998x_WIDTH; > >> + isl7998x->height = ISL7998x_HEIGHT; > >> + isl7998x->fmt = &isl7998x_colour_fmts[0]; > >> + > >> + ret = v4l2_ctrl_handler_init(&isl7998x->ctrl_handler, > >> + 2 + ARRAY_SIZE(isl7998x_ctrls)); > >> + if (ret) > >> + return ret; > >> + > >> + mutex_init(&isl7998x->ctrl_mutex); > >> + isl7998x->ctrl_handler.lock = &isl7998x->ctrl_mutex; > >> + isl7998x->link_freq = v4l2_ctrl_new_int_menu(&isl7998x->ctrl_handler, > >> + &isl7998x_ctrl_ops, V4L2_CID_LINK_FREQ, > >> + ARRAY_SIZE(link_freq_menu_items) - 1, > >> + endpoint.bus.mipi_csi2.num_data_lanes == 2 ? > >> + 1 : 0, link_freq_menu_items); > >> + isl7998x->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; > >> + > >> + for (i = 0; i < ARRAY_SIZE(isl7998x_ctrls); i++) { > >> + v4l2_ctrl_new_custom(&isl7998x->ctrl_handler, > >> + &isl7998x_ctrls[i], NULL); > >> + } > >> + > >> + v4l2_ctrl_new_std_menu_items(&isl7998x->ctrl_handler, > >> + &isl7998x_ctrl_ops, V4L2_CID_TEST_PATTERN, > >> + ARRAY_SIZE(isl7998x_test_pattern_menu) - 1, > >> + 0, 0, isl7998x_test_pattern_menu); > >> + > > > > Before registering the handler please check if ctrl_handler.error > > reports if anything has failed. > > Eh ? v4l2_ctrl_new_*() will set the ctrl_handler.error ? That's weird, > shouldn't it just return an error value then ? > It does not afaict and you should check the value of the .error flag > >> + isl7998x->subdev.ctrl_handler = &isl7998x->ctrl_handler; > >> + > >> + isl7998x->subdev.dev = dev; > > > > v4l2_i2c_subdev_init does this for you. Doesn't hurt though. > > > >> + ret = v4l2_async_register_subdev(&isl7998x->subdev); > >> + if (ret < 0) > >> + goto err_entity_cleanup; > >> + > >> + /* > >> + * Turn the chip ON and keep it ON, otherwise the camera standard > >> + * detection takes about 600 mS every time we do VIDIOC_G_FMT. > >> + */ > > > > ouch. do you need to query the HW at G_FMT time? Can't you cache the > > lastly applied format and return it without having to keep the chip > > on? The same for s_fmt, if the device is powered off, cache the format > > and apply at s_stream time. Is this possible with this device? > > Ideally, I would be able to switch the connected cameras at runtime and > then re-detect the standard. But I don't think the media framework has > any way to implement this and avoid the delay. It does not support replug and reconfiguration of a media graph, but since you don't have any input pad, the media graph re-configuration here does not play a role. Anyway keeping the chip on so you can switch cameras at runtime is imo an hack and should be kept in an out of tree patch if you want so in your device. > > [...] [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x 2019-05-20 20:18 ` [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x Marek Vasut 2019-07-01 7:58 ` Jacopo Mondi @ 2019-07-01 8:43 ` Sakari Ailus 2019-08-06 14:25 ` Marek Vasut 2019-07-01 8:46 ` Sakari Ailus 2 siblings, 1 reply; 22+ messages in thread From: Sakari Ailus @ 2019-07-01 8:43 UTC (permalink / raw) To: Marek Vasut; +Cc: linux-media, Mauro Carvalho Chehab, Rob Herring Hi Marek, Thank you for the patchset --- and my apologies for reviewing it so late. On Mon, May 20, 2019 at 10:18:12PM +0200, Marek Vasut wrote: > Add driver for the Intersil ISL7998x BT656-to-MIPI-CSI2 video decoder. > This chip supports 1/2/4 analog video inputs and converts them into > 1/2/4 VCs in MIPI CSI2 stream. > > This driver currently supports ISL79987 and both 720x480 and 720x576 > resolutions, however as per specification, all inputs must use the > same resolution and standard. The only supported pixel format is now > YUYV/YUV422. The chip should support RGB565 on the CSI2 as well, but > this is currently unsupported. > > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Sakari Ailus <sakari.ailus@linux.intel.com> > Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> > Cc: Rob Herring <robh+dt@kernel.org> > To: linux-media@vger.kernel.org > --- > drivers/media/i2c/Kconfig | 6 + > drivers/media/i2c/Makefile | 1 + > drivers/media/i2c/isl7998x.c | 1111 ++++++++++++++++++++++++++++++++++ > 3 files changed, 1118 insertions(+) > create mode 100644 drivers/media/i2c/isl7998x.c > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index 7793358ab8b3..af2ea08d6c59 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -929,6 +929,12 @@ config VIDEO_NOON010PC30 > help > This driver supports NOON010PC30 CIF camera from Siliconfile > > +config VIDEO_ISL7998X > + tristate "Intersil ISL7998x support" > + depends on I2C && VIDEO_V4L2 > + help > + This driver supports Intersil ISL7998x BT656-to-MIPI-CSI2 bridge. > + > source "drivers/media/i2c/m5mols/Kconfig" > > config VIDEO_RJ54N1 > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile > index d8ad9dad495d..a66f105a7bcc 100644 > --- a/drivers/media/i2c/Makefile > +++ b/drivers/media/i2c/Makefile > @@ -113,6 +113,7 @@ obj-$(CONFIG_VIDEO_IMX258) += imx258.o > obj-$(CONFIG_VIDEO_IMX274) += imx274.o > obj-$(CONFIG_VIDEO_IMX319) += imx319.o > obj-$(CONFIG_VIDEO_IMX355) += imx355.o > +obj-$(CONFIG_VIDEO_ISL7998X) += isl7998x.o > obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o > > obj-$(CONFIG_SDR_MAX2175) += max2175.o > diff --git a/drivers/media/i2c/isl7998x.c b/drivers/media/i2c/isl7998x.c > new file mode 100644 > index 000000000000..858e98d8b494 > --- /dev/null > +++ b/drivers/media/i2c/isl7998x.c > @@ -0,0 +1,1111 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Intersil ISL7998x BT656-to-MIPI-CSI2 driver > + * > + * Copyright (C) 2018-2019 Marek Vasut <marex@denx.de> > + */ > +#include <linux/videodev2.h> > +#include <linux/delay.h> > +#include <linux/gpio.h> > +#include <linux/i2c.h> > +#include <linux/log2.h> > +#include <linux/module.h> > +#include <linux/of_graph.h> > +#include <linux/regmap.h> > +#include <linux/slab.h> > +#include <linux/v4l2-mediabus.h> > +#include <media/v4l2-async.h> > +#include <media/v4l2-clk.h> > +#include <media/v4l2-common.h> > +#include <media/v4l2-ctrls.h> > +#include <media/v4l2-device.h> > +#include <media/v4l2-fwnode.h> Alphabetical order, please. > + > +#define ISL7998x_WIDTH 720 > +#define ISL7998x_HEIGHT 480 > +#define ISL7998x_INPUTS 4 > + > +#define V4L2_CID_TEST_PATTERN_COLOR (V4L2_CID_USER_BASE | 0x1001) > +#define V4L2_CID_TEST_PATTERN_CHANNELS (V4L2_CID_USER_BASE | 0x1002) > +#define V4L2_CID_TEST_PATTERN_BARS (V4L2_CID_USER_BASE | 0x1003) > + > +#define ISL7998x_REG(page, reg) (((page) << 8) | (reg)) > + > +#define ISL7998x_REG_Pn_SIZE 256 > +#define ISL7998x_REG_Pn_BASE(n) ((n) * ISL7998x_REG_Pn_SIZE) > + > +#define ISL7998x_REG_Px_DEC_PAGE(page) ISL7998x_REG((page), 0xff) > +#define ISL7998x_REG_Px_DEC_PAGE_MASK 0xf > +#define ISL7998x_REG_P0_PRODUCT_ID_CODE ISL7998x_REG(0, 0x00) > +#define ISL7998x_REG_P0_PRODUCT_REV_CODE ISL7998x_REG(0, 0x01) > +#define ISL7998x_REG_P0_SW_RESET_CTL ISL7998x_REG(0, 0x02) > +#define ISL7998x_REG_P0_IO_BUFFER_CTL ISL7998x_REG(0, 0x03) > +#define ISL7998x_REG_P0_IO_BUFFER_CTL_1_1 ISL7998x_REG(0, 0x04) > +#define ISL7998x_REG_P0_IO_PAD_PULL_EN_CTL ISL7998x_REG(0, 0x05) > +#define ISL7998x_REG_P0_IO_BUFFER_CTL_1_2 ISL7998x_REG(0, 0x06) > +#define ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL ISL7998x_REG(0, 0x07) > +#define ISL7998x_REG_P0_CLK_CTL_1 ISL7998x_REG(0, 0x08) > +#define ISL7998x_REG_P0_CLK_CTL_2 ISL7998x_REG(0, 0x09) > +#define ISL7998x_REG_P0_CLK_CTL_3 ISL7998x_REG(0, 0x0a) > +#define ISL7998x_REG_P0_CLK_CTL_4 ISL7998x_REG(0, 0x0b) > +#define ISL7998x_REG_P0_MPP1_SYNC_CTL ISL7998x_REG(0, 0x0c) > +#define ISL7998x_REG_P0_MPP2_SYNC_CTL ISL7998x_REG(0, 0x0d) > +#define ISL7998x_REG_P0_IRQ_SYNC_CTL ISL7998x_REG(0, 0x0e) > +#define ISL7998x_REG_P0_INTERRUPT_STATUS ISL7998x_REG(0, 0x10) > +#define ISL7998x_REG_P0_CHAN_1_IRQ ISL7998x_REG(0, 0x11) > +#define ISL7998x_REG_P0_CHAN_2_IRQ ISL7998x_REG(0, 0x12) > +#define ISL7998x_REG_P0_CHAN_3_IRQ ISL7998x_REG(0, 0x13) > +#define ISL7998x_REG_P0_CHAN_4_IRQ ISL7998x_REG(0, 0x14) > +#define ISL7998x_REG_P0_SHORT_DIAG_IRQ ISL7998x_REG(0, 0x15) > +#define ISL7998x_REG_P0_CHAN_1_IRQ_EN ISL7998x_REG(0, 0x16) > +#define ISL7998x_REG_P0_CHAN_2_IRQ_EN ISL7998x_REG(0, 0x17) > +#define ISL7998x_REG_P0_CHAN_3_IRQ_EN ISL7998x_REG(0, 0x18) > +#define ISL7998x_REG_P0_CHAN_4_IRQ_EN ISL7998x_REG(0, 0x19) > +#define ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN ISL7998x_REG(0, 0x1a) > +#define ISL7998x_REG_P0_CHAN_1_STATUS ISL7998x_REG(0, 0x1b) > +#define ISL7998x_REG_P0_CHAN_2_STATUS ISL7998x_REG(0, 0x1c) > +#define ISL7998x_REG_P0_CHAN_3_STATUS ISL7998x_REG(0, 0x1d) > +#define ISL7998x_REG_P0_CHAN_4_STATUS ISL7998x_REG(0, 0x1e) > +#define ISL7998x_REG_P0_SHORT_DIAG_STATUS ISL7998x_REG(0, 0x1f) > +#define ISL7998x_REG_P0_CLOCK_DELAY ISL7998x_REG(0, 0x20) > + > +#define ISL7998x_REG_Px_DEC_INPUT_FMT(pg) ISL7998x_REG((pg), 0x02) > +#define ISL7998x_REG_Px_DEC_STATUS_1(pg) ISL7998x_REG((pg), 0x03) > +#define ISL7998x_REG_Px_DEC_HS_DELAY_CTL(pg) ISL7998x_REG((pg), 0x04) > +#define ISL7998x_REG_Px_DEC_ANCTL(pg) ISL7998x_REG((pg), 0x06) > +#define ISL7998x_REG_Px_DEC_CROP_HI(pg) ISL7998x_REG((pg), 0x07) > +#define ISL7998x_REG_Px_DEC_VDELAY_LO(pg) ISL7998x_REG((pg), 0x08) > +#define ISL7998x_REG_Px_DEC_VACTIVE_LO(pg) ISL7998x_REG((pg), 0x09) > +#define ISL7998x_REG_Px_DEC_HDELAY_LO(pg) ISL7998x_REG((pg), 0x0a) > +#define ISL7998x_REG_Px_DEC_HACTIVE_LO(pg) ISL7998x_REG((pg), 0x0b) > +#define ISL7998x_REG_Px_DEC_CNTRL1(pg) ISL7998x_REG((pg), 0x0c) > +#define ISL7998x_REG_Px_DEC_CSC_CTL(pg) ISL7998x_REG((pg), 0x0d) > +#define ISL7998x_REG_Px_DEC_BRIGHT(pg) ISL7998x_REG((pg), 0x10) > +#define ISL7998x_REG_Px_DEC_CONTRAST(pg) ISL7998x_REG((pg), 0x11) > +#define ISL7998x_REG_Px_DEC_SHARPNESS(pg) ISL7998x_REG((pg), 0x12) > +#define ISL7998x_REG_Px_DEC_SAT_U(pg) ISL7998x_REG((pg), 0x13) > +#define ISL7998x_REG_Px_DEC_SAT_V(pg) ISL7998x_REG((pg), 0x14) > +#define ISL7998x_REG_Px_DEC_HUE(pg) ISL7998x_REG((pg), 0x15) > +#define ISL7998x_REG_Px_DEC_VERT_PEAK(pg) ISL7998x_REG((pg), 0x17) > +#define ISL7998x_REG_Px_DEC_CORING(pg) ISL7998x_REG((pg), 0x18) > +#define ISL7998x_REG_Px_DEC_SDT(pg) ISL7998x_REG((pg), 0x1c) > +#define ISL7998x_REG_Px_DEC_SDT_DET BIT(7) > +#define ISL7998x_REG_Px_DEC_SDTR(pg) ISL7998x_REG((pg), 0x1d) > +#define ISL7998x_REG_Px_DEC_CLMPG(pg) ISL7998x_REG((pg), 0x20) > +#define ISL7998x_REG_Px_DEC_IAGC(pg) ISL7998x_REG((pg), 0x21) > +#define ISL7998x_REG_Px_DEC_AGCGAIN(pg) ISL7998x_REG((pg), 0x22) > +#define ISL7998x_REG_Px_DEC_PEAKWT(pg) ISL7998x_REG((pg), 0x23) > +#define ISL7998x_REG_Px_DEC_CLMPL(pg) ISL7998x_REG((pg), 0x24) > +#define ISL7998x_REG_Px_DEC_SYNCT(pg) ISL7998x_REG((pg), 0x25) > +#define ISL7998x_REG_Px_DEC_MISSCNT(pg) ISL7998x_REG((pg), 0x26) > +#define ISL7998x_REG_Px_DEC_PCLAMP(pg) ISL7998x_REG((pg), 0x27) > +#define ISL7998x_REG_Px_DEC_VERT_CTL_1(pg) ISL7998x_REG((pg), 0x28) > +#define ISL7998x_REG_Px_DEC_VERT_CTL_2(pg) ISL7998x_REG((pg), 0x29) > +#define ISL7998x_REG_Px_DEC_CLR_KILL_LVL(pg) ISL7998x_REG((pg), 0x2a) > +#define ISL7998x_REG_Px_DEC_COMB_FILTER_CTL(pg) ISL7998x_REG((pg), 0x2b) > +#define ISL7998x_REG_Px_DEC_LUMA_DELAY(pg) ISL7998x_REG((pg), 0x2c) > +#define ISL7998x_REG_Px_DEC_MISC1(pg) ISL7998x_REG((pg), 0x2d) > +#define ISL7998x_REG_Px_DEC_MISC2(pg) ISL7998x_REG((pg), 0x2e) > +#define ISL7998x_REG_Px_DEC_MISC3(pg) ISL7998x_REG((pg), 0x2f) > +#define ISL7998x_REG_Px_DEC_MVSN(pg) ISL7998x_REG((pg), 0x30) > +#define ISL7998x_REG_Px_DEC_CSTATUS2(pg) ISL7998x_REG((pg), 0x31) > +#define ISL7998x_REG_Px_DEC_HFREF(pg) ISL7998x_REG((pg), 0x32) > +#define ISL7998x_REG_Px_DEC_CLMD(pg) ISL7998x_REG((pg), 0x33) > +#define ISL7998x_REG_Px_DEC_ID_DET_CTL(pg) ISL7998x_REG((pg), 0x34) > +#define ISL7998x_REG_Px_DEC_CLCNTL(pg) ISL7998x_REG((pg), 0x35) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_1(pg) ISL7998x_REG((pg), 0x36) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_2(pg) ISL7998x_REG((pg), 0x37) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_3(pg) ISL7998x_REG((pg), 0x38) > +#define ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_4(pg) ISL7998x_REG((pg), 0x39) > +#define ISL7998x_REG_Px_DEC_SHORT_DET_CTL(pg) ISL7998x_REG((pg), 0x3a) > +#define ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(pg) ISL7998x_REG((pg), 0x3b) > +#define ISL7998x_REG_Px_DEC_AFE_TST_MUX_CTL(pg) ISL7998x_REG((pg), 0x3c) > +#define ISL7998x_REG_Px_DEC_DATA_CONV(pg) ISL7998x_REG((pg), 0x3d) > +#define ISL7998x_REG_Px_DEC_INTERNAL_TEST(pg) ISL7998x_REG((pg), 0x3f) > +#define ISL7998x_REG_Px_DEC_H_DELAY_CTL(pg) ISL7998x_REG((pg), 0x43) > +#define ISL7998x_REG_Px_DEC_H_DELAY_II_HI(pg) ISL7998x_REG((pg), 0x44) > +#define ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(pg) ISL7998x_REG((pg), 0x45) > + > +#define ISL7998x_REG_Px_ACA_CTL_1(pg) ISL7998x_REG((pg), 0x80) > +#define ISL7998x_REG_Px_ACA_GAIN_CTL(pg) ISL7998x_REG((pg), 0x81) > +#define ISL7998x_REG_Px_ACA_Y_AVG_HI_LIMIT(pg) ISL7998x_REG((pg), 0x82) > +#define ISL7998x_REG_Px_ACA_Y_AVG_LO_LIMIT(pg) ISL7998x_REG((pg), 0x83) > +#define ISL7998x_REG_Px_ACA_Y_DET_THRESHOLD(pg) ISL7998x_REG((pg), 0x84) > +#define ISL7998x_REG_Px_ACA_BLACK_LVL(pg) ISL7998x_REG((pg), 0x85) > +#define ISL7998x_REG_Px_ACA_CENTER_LVL(pg) ISL7998x_REG((pg), 0x86) > +#define ISL7998x_REG_Px_ACA_WHITE_LVL(pg) ISL7998x_REG((pg), 0x87) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_LIMIT(pg) ISL7998x_REG((pg), 0x88) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_UPGAIN(pg) ISL7998x_REG((pg), 0x89) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_SLOPE(pg) ISL7998x_REG((pg), 0x8a) > +#define ISL7998x_REG_Px_ACA_MEAN_OFF_DNGAIN(pg) ISL7998x_REG((pg), 0x8b) > +#define ISL7998x_REG_Px_ACA_DELTA_CO_THRES(pg) ISL7998x_REG((pg), 0x8c) > +#define ISL7998x_REG_Px_ACA_DELTA_SLOPE(pg) ISL7998x_REG((pg), 0x8d) > +#define ISL7998x_REG_Px_ACA_LO_HI_AVG_THRES(pg) ISL7998x_REG((pg), 0x8e) > +#define ISL7998x_REG_Px_ACA_LO_MAX_LVL_CTL(pg) ISL7998x_REG((pg), 0x8f) > +#define ISL7998x_REG_Px_ACA_HI_MAX_LVL_CTL(pg) ISL7998x_REG((pg), 0x90) > +#define ISL7998x_REG_Px_ACA_LO_UPGAIN_CTL(pg) ISL7998x_REG((pg), 0x91) > +#define ISL7998x_REG_Px_ACA_LO_DNGAIN_CTL(pg) ISL7998x_REG((pg), 0x92) > +#define ISL7998x_REG_Px_ACA_HI_UPGAIN_CTL(pg) ISL7998x_REG((pg), 0x93) > +#define ISL7998x_REG_Px_ACA_HI_DNGAIN_CTL(pg) ISL7998x_REG((pg), 0x94) > +#define ISL7998x_REG_Px_ACA_LOPASS_FLT_COEF(pg) ISL7998x_REG((pg), 0x95) > +#define ISL7998x_REG_Px_ACA_PDF_INDEX(pg) ISL7998x_REG((pg), 0x96) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_STT(pg) ISL7998x_REG((pg), 0x97) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_SZ1(pg) ISL7998x_REG((pg), 0x98) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_H_SZ2(pg) ISL7998x_REG((pg), 0x99) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_STT(pg) ISL7998x_REG((pg), 0x9a) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ1(pg) ISL7998x_REG((pg), 0x9b) > +#define ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(pg) ISL7998x_REG((pg), 0x9c) > +#define ISL7998x_REG_Px_ACA_Y_AVG(pg) ISL7998x_REG((pg), 0xa0) > +#define ISL7998x_REG_Px_ACA_Y_AVG_LIM(pg) ISL7998x_REG((pg), 0xa1) > +#define ISL7998x_REG_Px_ACA_LO_AVG(pg) ISL7998x_REG((pg), 0xa2) > +#define ISL7998x_REG_Px_ACA_HI_AVG(pg) ISL7998x_REG((pg), 0xa3) > +#define ISL7998x_REG_Px_ACA_Y_MAX(pg) ISL7998x_REG((pg), 0xa4) > +#define ISL7998x_REG_Px_ACA_Y_MIN(pg) ISL7998x_REG((pg), 0xa5) > +#define ISL7998x_REG_Px_ACA_MOFFSET(pg) ISL7998x_REG((pg), 0xa6) > +#define ISL7998x_REG_Px_ACA_LO_GAIN(pg) ISL7998x_REG((pg), 0xa7) > +#define ISL7998x_REG_Px_ACA_HI_GAIN(pg) ISL7998x_REG((pg), 0xa8) > +#define ISL7998x_REG_Px_ACA_LL_SLOPE(pg) ISL7998x_REG((pg), 0xa9) > +#define ISL7998x_REG_Px_ACA_LH_SLOPE(pg) ISL7998x_REG((pg), 0xaa) > +#define ISL7998x_REG_Px_ACA_HL_SLOPE(pg) ISL7998x_REG((pg), 0xab) > +#define ISL7998x_REG_Px_ACA_HH_SLOPE(pg) ISL7998x_REG((pg), 0xac) > +#define ISL7998x_REG_Px_ACA_X_LOW(pg) ISL7998x_REG((pg), 0xad) > +#define ISL7998x_REG_Px_ACA_X_MEAN(pg) ISL7998x_REG((pg), 0xae) > +#define ISL7998x_REG_Px_ACA_X_HIGH(pg) ISL7998x_REG((pg), 0xaf) > +#define ISL7998x_REG_Px_ACA_Y_LOW(pg) ISL7998x_REG((pg), 0xb0) > +#define ISL7998x_REG_Px_ACA_Y_MEAN(pg) ISL7998x_REG((pg), 0xb1) > +#define ISL7998x_REG_Px_ACA_Y_HIGH(pg) ISL7998x_REG((pg), 0xb2) > +#define ISL7998x_REG_Px_ACA_CTL_2(pg) ISL7998x_REG((pg), 0xb3) > +#define ISL7998x_REG_Px_ACA_CTL_3(pg) ISL7998x_REG((pg), 0xb4) > +#define ISL7998x_REG_Px_ACA_CTL_4(pg) ISL7998x_REG((pg), 0xb5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(pg) ISL7998x_REG((pg), 0xc0) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TL_H(pg) ISL7998x_REG((pg), 0xc1) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TL_L(pg) ISL7998x_REG((pg), 0xc2) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TL_H(pg) ISL7998x_REG((pg), 0xc3) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TL_L(pg) ISL7998x_REG((pg), 0xc4) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TR_H(pg) ISL7998x_REG((pg), 0xc5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TR_L(pg) ISL7998x_REG((pg), 0xc6) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TR_H(pg) ISL7998x_REG((pg), 0xc7) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TR_L(pg) ISL7998x_REG((pg), 0xc8) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BL_H(pg) ISL7998x_REG((pg), 0xc9) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BL_L(pg) ISL7998x_REG((pg), 0xca) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BL_H(pg) ISL7998x_REG((pg), 0xcb) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BL_L(pg) ISL7998x_REG((pg), 0xcc) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BR_H(pg) ISL7998x_REG((pg), 0xcd) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BR_L(pg) ISL7998x_REG((pg), 0xce) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BR_H(pg) ISL7998x_REG((pg), 0xcf) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BR_L(pg) ISL7998x_REG((pg), 0xd0) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_LM_H(pg) ISL7998x_REG((pg), 0xd1) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_LM_L(pg) ISL7998x_REG((pg), 0xd2) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_LM_H(pg) ISL7998x_REG((pg), 0xd3) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_LM_L(pg) ISL7998x_REG((pg), 0xd4) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TM_H(pg) ISL7998x_REG((pg), 0xd5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_TM_L(pg) ISL7998x_REG((pg), 0xd6) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TM_H(pg) ISL7998x_REG((pg), 0xd7) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_TM_L(pg) ISL7998x_REG((pg), 0xd8) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BM_H(pg) ISL7998x_REG((pg), 0xd9) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_BM_L(pg) ISL7998x_REG((pg), 0xda) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BM_H(pg) ISL7998x_REG((pg), 0xdb) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_BM_L(pg) ISL7998x_REG((pg), 0xdc) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_RM_H(pg) ISL7998x_REG((pg), 0xdd) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_X_RM_L(pg) ISL7998x_REG((pg), 0xde) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_RM_H(pg) ISL7998x_REG((pg), 0xdf) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_RM_L(pg) ISL7998x_REG((pg), 0xe0) > +#define ISL7998x_REG_Px_ACA_HIST_DATA_LO(pg) ISL7998x_REG((pg), 0xe1) > +#define ISL7998x_REG_Px_ACA_HIST_DATA_MID(pg) ISL7998x_REG((pg), 0xe2) > +#define ISL7998x_REG_Px_ACA_HIST_DATA_HI(pg) ISL7998x_REG((pg), 0xe3) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_Y_CLR(pg) ISL7998x_REG((pg), 0xe4) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_CB_CLR(pg) ISL7998x_REG((pg), 0xe5) > +#define ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(pg) ISL7998x_REG((pg), 0xe6) > +#define ISL7998x_REG_Px_ACA_XFER_HIST_HOST(pg) ISL7998x_REG((pg), 0xe7) > + > +#define ISL7998x_REG_P5_LI_ENGINE_CTL ISL7998x_REG(5, 0x00) > +#define ISL7998x_REG_P5_LI_ENGINE_LINE_CTL ISL7998x_REG(5, 0x01) > +#define ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH ISL7998x_REG(5, 0x02) > +#define ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL ISL7998x_REG(5, 0x03) > +#define ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT ISL7998x_REG(5, 0x04) > +#define ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL ISL7998x_REG(5, 0x05) > +#define ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL ISL7998x_REG(5, 0x06) > +#define ISL7998x_REG_P5_MIPI_READ_START_CTL ISL7998x_REG(5, 0x07) > +#define ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL ISL7998x_REG(5, 0x08) > +#define ISL7998x_REG_P5_ONE_FIELD_MODE_CTL ISL7998x_REG(5, 0x09) > +#define ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR ISL7998x_REG(5, 0x0a) > +#define ISL7998x_REG_P5_TP_GEN_BAR_PATTERN ISL7998x_REG(5, 0x0b) > +#define ISL7998x_REG_P5_MIPI_PCNT_PSFRM ISL7998x_REG(5, 0x0c) > +#define ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL ISL7998x_REG(5, 0x0d) > +#define ISL7998x_REG_P5_MIPI_VBLANK_PSFRM ISL7998x_REG(5, 0x0e) > +#define ISL7998x_REG_P5_LI_ENGINE_CTL_2 ISL7998x_REG(5, 0x0f) > +#define ISL7998x_REG_P5_MIPI_WCNT_1 ISL7998x_REG(5, 0x10) > +#define ISL7998x_REG_P5_MIPI_WCNT_2 ISL7998x_REG(5, 0x11) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1 ISL7998x_REG(5, 0x12) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2 ISL7998x_REG(5, 0x13) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3 ISL7998x_REG(5, 0x14) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4 ISL7998x_REG(5, 0x15) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5 ISL7998x_REG(5, 0x16) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6 ISL7998x_REG(5, 0x17) > +#define ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1 ISL7998x_REG(5, 0x18) > +#define ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD ISL7998x_REG(5, 0x19) > +#define ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD ISL7998x_REG(5, 0x1a) > +#define ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2 ISL7998x_REG(5, 0x1b) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7 ISL7998x_REG(5, 0x1c) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8 ISL7998x_REG(5, 0x1d) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9 ISL7998x_REG(5, 0x1e) > +#define ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_10 ISL7998x_REG(5, 0x1f) > +#define ISL7998x_REG_P5_TP_GEN_MIPI ISL7998x_REG(5, 0x20) > +#define ISL7998x_REG_P5_ESC_MODE_TIME_CTL ISL7998x_REG(5, 0x21) > +#define ISL7998x_REG_P5_AUTO_TEST_ERR_DET ISL7998x_REG(5, 0x22) > +#define ISL7998x_REG_P5_MIPI_TIMING ISL7998x_REG(5, 0x23) > +#define ISL7998x_REG_P5_PIC_HEIGHT_HIGH ISL7998x_REG(5, 0x24) > +#define ISL7998x_REG_P5_PIC_HEIGHT_LOW ISL7998x_REG(5, 0x25) > +#define ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL ISL7998x_REG(5, 0x26) > +#define ISL7998x_REG_P5_FIFO_THRSH_CNT_1 ISL7998x_REG(5, 0x28) > +#define ISL7998x_REG_P5_FIFO_THRSH_CNT_2 ISL7998x_REG(5, 0x29) > +#define ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1 ISL7998x_REG(5, 0x2a) > +#define ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2 ISL7998x_REG(5, 0x2b) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_1 ISL7998x_REG(5, 0x2c) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_2 ISL7998x_REG(5, 0x2d) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_3 ISL7998x_REG(5, 0x2e) > +#define ISL7998x_REG_P5_PSF_FIELD_END_CTL_4 ISL7998x_REG(5, 0x2f) > +#define ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1 ISL7998x_REG(5, 0x30) > +#define ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2 ISL7998x_REG(5, 0x31) > +#define ISL7998x_REG_P5_MIPI_ANA_CLK_CTL ISL7998x_REG(5, 0x32) > +#define ISL7998x_REG_P5_PLL_ANA_STATUS ISL7998x_REG(5, 0x33) > +#define ISL7998x_REG_P5_PLL_ANA_MISC_CTL ISL7998x_REG(5, 0x34) > +#define ISL7998x_REG_P5_MIPI_ANA ISL7998x_REG(5, 0x35) > +#define ISL7998x_REG_P5_PLL_ANA ISL7998x_REG(5, 0x36) > +#define ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1 ISL7998x_REG(5, 0x38) > +#define ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2 ISL7998x_REG(5, 0x39) > +#define ISL7998x_REG_P5_H_LINE_CNT_1 ISL7998x_REG(5, 0x3a) > +#define ISL7998x_REG_P5_H_LINE_CNT_2 ISL7998x_REG(5, 0x3b) > +#define ISL7998x_REG_P5_HIST_LINE_CNT_1 ISL7998x_REG(5, 0x3c) > +#define ISL7998x_REG_P5_HIST_LINE_CNT_2 ISL7998x_REG(5, 0x3d) > + > +static const struct reg_sequence isl7998x_init_seq_1[] = { > + { ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN, 0xff }, > + { ISL7998x_REG_Px_DEC_SDT(0x1), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x1), 0x03 }, > + { ISL7998x_REG_Px_DEC_SDT(0x2), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x2), 0x03 }, > + { ISL7998x_REG_Px_DEC_SDT(0x3), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x3), 0x03 }, > + { ISL7998x_REG_Px_DEC_SDT(0x4), 0x07 }, > + { ISL7998x_REG_Px_DEC_SHORT_DET_CTL_1(0x4), 0x03 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x00 }, > + { ISL7998x_REG_P0_SW_RESET_CTL, 0x1f, 10 }, > + { ISL7998x_REG_P0_IO_BUFFER_CTL, 0x00 }, > + { ISL7998x_REG_P0_MPP2_SYNC_CTL, 0xc9 }, > + { ISL7998x_REG_P0_IRQ_SYNC_CTL, 0xc9 }, > + { ISL7998x_REG_P0_CHAN_1_IRQ, 0x03 }, > + { ISL7998x_REG_P0_CHAN_2_IRQ, 0x00 }, > + { ISL7998x_REG_P0_CHAN_3_IRQ, 0x00 }, > + { ISL7998x_REG_P0_CHAN_4_IRQ, 0x00 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL, 0x02 }, > + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, 0x85 }, > + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, 0xa0 }, > + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x18 }, > + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x40 }, > + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x40 }, > + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, > + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, > + { ISL7998x_REG_P5_TP_GEN_MIPI, 0x00 }, > + { ISL7998x_REG_P5_ESC_MODE_TIME_CTL, 0x0c }, > + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x00 }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x19 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_1, 0x18 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_2, 0xf1 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_3, 0x00 }, > + { ISL7998x_REG_P5_PSF_FIELD_END_CTL_4, 0xf1 }, > + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_1, 0x00 }, > + { ISL7998x_REG_P5_MIPI_ANA_DATA_CTL_2, 0x00 }, > + { ISL7998x_REG_P5_MIPI_ANA_CLK_CTL, 0x00 }, > + { ISL7998x_REG_P5_PLL_ANA_STATUS, 0xc0 }, > + { ISL7998x_REG_P5_PLL_ANA_MISC_CTL, 0x18 }, > + { ISL7998x_REG_P5_PLL_ANA, 0x00 }, > + { ISL7998x_REG_P0_SW_RESET_CTL, 0x10, 10 }, > + /* Page 0xf means write to all of pages 1,2,3,4 */ > + { ISL7998x_REG_Px_DEC_VDELAY_LO(0xf), 0x14 }, > + { ISL7998x_REG_Px_DEC_MISC3(0xf), 0xe6 }, > + { ISL7998x_REG_Px_DEC_CLMD(0xf), 0x85 }, > + { ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(0xf), 0x11 }, > + { ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), 0x00 }, > + { ISL7998x_REG_P0_CLK_CTL_1, 0x1f }, > + { ISL7998x_REG_P0_CLK_CTL_2, 0x43 }, > + { ISL7998x_REG_P0_CLK_CTL_3, 0x4f }, It'd be great to see what these magical numbers signify. How about some additional #defines for the bits? Same below. > +}; > + > +static const struct reg_sequence isl7998x_init_seq_2[] = { > + { ISL7998x_REG_P5_LI_ENGINE_SYNC_CTL, 0x10 }, > + { ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT, 0xe4 }, > + { ISL7998x_REG_P5_LI_ENGINE_TYPE_CTL, 0x00 }, > + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x60 }, > + { ISL7998x_REG_P5_MIPI_READ_START_CTL, 0x2b }, > + { ISL7998x_REG_P5_PSEUDO_FRM_FIELD_CTL, 0x02 }, > + { ISL7998x_REG_P5_ONE_FIELD_MODE_CTL, 0x00 }, > + { ISL7998x_REG_P5_MIPI_INT_HW_TST_CTR, 0x62 }, > + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, 0x02 }, > + { ISL7998x_REG_P5_MIPI_PCNT_PSFRM, 0x36 }, > + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0x00 }, > + { ISL7998x_REG_P5_MIPI_VBLANK_PSFRM, 0x6c }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0x00 }, > + { ISL7998x_REG_P5_MIPI_WCNT_1, 0x05 }, > + { ISL7998x_REG_P5_MIPI_WCNT_2, 0xa0 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_1, 0x77 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_2, 0x17 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_3, 0x08 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_4, 0x38 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_5, 0x14 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_6, 0xf6 }, > + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_1, 0x00 }, > + { ISL7998x_REG_P5_MIPI_DPHY_SOT_PERIOD, 0x17 }, > + { ISL7998x_REG_P5_MIPI_DPHY_EOT_PERIOD, 0x0a }, > + { ISL7998x_REG_P5_MIPI_DPHY_PARAMS_2, 0x71 }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_7, 0x7a }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_8, 0x0f }, > + { ISL7998x_REG_P5_MIPI_DPHY_TIMING_CTL_9, 0x8c }, > + { ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, 0x08 }, > + { ISL7998x_REG_P5_FIFO_THRSH_CNT_1, 0x01 }, > + { ISL7998x_REG_P5_FIFO_THRSH_CNT_2, 0x0e }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_1, 0x00 }, > + { ISL7998x_REG_P5_TP_GEN_RND_SYNC_CTL_2, 0x00 }, > + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, 0x03 }, > + { ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_2, 0xc0 }, > + { ISL7998x_REG_P5_H_LINE_CNT_1, 0x06 }, > + { ISL7998x_REG_P5_H_LINE_CNT_2, 0xb3 }, > + { ISL7998x_REG_P5_HIST_LINE_CNT_1, 0x00 }, > + { ISL7998x_REG_P5_HIST_LINE_CNT_2, 0xf1 }, > + { ISL7998x_REG_P5_LI_ENGINE_FIFO_CTL, 0x00 }, > + { ISL7998x_REG_P5_MIPI_ANA, 0x00 }, > + /* > + * Wait a bit after reset so that the chip can capture a frame > + * and update internal line counters. > + */ > + { ISL7998x_REG_P0_SW_RESET_CTL, 0x00, 50 }, > +}; > + > +struct isl7998x_datafmt { > + u32 code; > + enum v4l2_colorspace colorspace; > +}; > + > +static const struct isl7998x_datafmt isl7998x_colour_fmts[] = { > + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_SRGB }, > +}; > + > +/* Menu items for LINK_FREQ V4L2 control */ > +static const s64 link_freq_menu_items[] = { > + 108000000, 216000000, 432000000 > +}; Where to these numbers come from? > + > +/* Menu items for TEST_PATTERN V4L2 control */ > +static const char * const isl7998x_test_pattern_menu[] = { > + "Disabled", "Enabled-PAL (720x576)", "Enabled-NTSC (720x480)" > +}; > + > +struct isl7998x { > + struct v4l2_subdev subdev; > + struct regmap *regmap; > + struct gpio_desc *pd_gpio; > + unsigned int nr_mipi_lanes; > + u32 nr_inputs; > + > + unsigned int width; > + unsigned int height; > + const struct isl7998x_datafmt *fmt; > +#ifdef CONFIG_MEDIA_CONTROLLER > + struct media_pad pad; Hmm. Didn't you have four inputs in your device? > +#endif > + > + struct v4l2_ctrl_handler ctrl_handler; > + struct mutex ctrl_mutex; > + /* V4L2 Controls */ > + struct v4l2_ctrl *link_freq; > + u8 test_pattern_enabled; > + u8 test_pattern_bars; > + u8 test_pattern_chans; > + u8 test_pattern_color; > +}; > + > +static struct isl7998x *sd_to_isl7998x(struct v4l2_subdev *sd) > +{ > + return container_of(sd, struct isl7998x, subdev); > +} > + > +static struct isl7998x *i2c_to_isl7998x(const struct i2c_client *client) > +{ > + return sd_to_isl7998x(i2c_get_clientdata(client)); > +} > + > +static int isl7998x_init(struct isl7998x *isl7998x) > +{ > + const unsigned int lanes = isl7998x->nr_mipi_lanes; > + const u32 isl7998x_video_in_chan_map[] = { 0x00, 0x11, 0x02, 0x02 }; > + const struct reg_sequence isl7998x_init_seq_custom[] = { > + { ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL, > + isl7998x_video_in_chan_map[isl7998x->nr_inputs - 1] }, > + { ISL7998x_REG_P0_CLK_CTL_4, (lanes == 1) ? 0x40 : 0x41 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL, (lanes == 1) ? 0x01 : 0x02 }, > + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, > + 0x20 | ((isl7998x->width >> 7) & 0x1f) }, > + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, > + (isl7998x->width << 1) & 0xff }, > + }; > + struct regmap *regmap = isl7998x->regmap; > + int ret; > + > + ret = regmap_register_patch(regmap, isl7998x_init_seq_1, > + ARRAY_SIZE(isl7998x_init_seq_1)); > + if (ret) > + return ret; > + > + ret = regmap_register_patch(regmap, isl7998x_init_seq_custom, > + ARRAY_SIZE(isl7998x_init_seq_custom)); > + if (ret) > + return ret; > + > + return regmap_register_patch(regmap, isl7998x_init_seq_2, > + ARRAY_SIZE(isl7998x_init_seq_2)); > +} > + > +static int isl7998x_g_mbus_config(struct v4l2_subdev *sd, > + struct v4l2_mbus_config *cfg) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + > + cfg->type = V4L2_MBUS_CSI2_DPHY; > + cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; > + if (isl7998x->nr_mipi_lanes == 1) > + cfg->flags |= V4L2_MBUS_CSI2_1_LANE; > + else > + cfg->flags |= V4L2_MBUS_CSI2_2_LANE; Drivers nowadays generally get this from DT. You can omit this function safely. For dynamic configuration we'll need something else (Jacopo's been working on that with me). > + > + return 0; > +} > + > +static int isl7998x_s_stream(struct v4l2_subdev *sd, int enable) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + > + return isl7998x_init(isl7998x); Is this needed both to initialise the hardware as well as start streaming? Does this also enable the CSI-2 transmitter in driver's probe? This could be problematic for some receivers. > +} > + > +static int isl7998x_enum_mbus_code(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_mbus_code_enum *code) > +{ > + if (code->pad || code->index >= ARRAY_SIZE(isl7998x_colour_fmts)) > + return -EINVAL; > + > + code->code = isl7998x_colour_fmts[code->index].code; A newline would be nice here. > + return 0; > +} > + > +static const unsigned int isl7998x_std_res[] = { > + 480, 576, 576, 480, 480, 576, 480, 480 > +}; > + > +static int isl7998x_update_std(struct isl7998x *isl7998x) > +{ > + unsigned int height[ISL7998x_INPUTS]; > + u8 scanning = GENMASK(ISL7998x_INPUTS - 1, 0); > + unsigned int i; > + int ret; > + u32 reg; > + > + while (true) { > + for (i = 0; i < ISL7998x_INPUTS; i++) { > + ret = regmap_read(isl7998x->regmap, > + ISL7998x_REG_Px_DEC_SDT(i + 1), ®); > + if (ret) > + return ret; > + > + /* Detection is still in progress, restart. */ > + if (reg & ISL7998x_REG_Px_DEC_SDT_DET) { > + scanning = GENMASK(ISL7998x_INPUTS - 1, 0); > + break; > + } > + > + scanning &= ~BIT(i); > + height[i] = isl7998x_std_res[(reg >> 4) & 0x7]; > + } > + > + if (!scanning) > + break; > + > + mdelay(1); How long does this take in general? Could you use msleep() instead of mdelay() in order to avoid a busy loop at least seemingly of unknown length? > + } > + > + /* > + * According to Renesas FAE, all input cameras must have the > + * same standard on this chip. > + */ > + for (i = 1; i < isl7998x->nr_inputs ; i++) > + if (height[i - 1] != height[i]) > + return -EINVAL; > + > + isl7998x->height = height[0]; > + > + return 0; > +} > + > +static int isl7998x_get_fmt(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *format) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + struct v4l2_mbus_framefmt *mf = &format->format; > + > + if (format->pad != 0) > + return -EINVAL; > + > + if (isl7998x->test_pattern_enabled == 1) { > + mf->width = 720; > + mf->height = 576; > + } else if (isl7998x->test_pattern_enabled == 2) { > + mf->width = 720; > + mf->height = 480; > + } else { > + mf->width = isl7998x->width; > + mf->height = isl7998x->height; > + } > + > + mf->code = isl7998x->fmt->code; > + mf->field = V4L2_FIELD_INTERLACED; > + mf->colorspace = 0; > + > + return 0; > +} > + > +static int isl7998x_set_fmt(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *format) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + struct v4l2_mbus_framefmt *mf = &format->format; > + int ret; > + > + if (format->pad != 0) > + return -EINVAL; You can omit the pad checks in pad ops; the framework does that nowadays. > + > + if (format->format.width != 720 || > + (format->format.height != 480 && format->format.height != 576)) > + return -EINVAL; > + > + if (format->format.code != MEDIA_BUS_FMT_YUYV8_2X8) > + return -EINVAL; Instead of returning an error, you should simply pick a valid format if the user-supplied format (mbus code, size) isn't supported. > + > + mf->width = format->format.width; > + mf->height = format->format.height; > + mf->code = format->format.code; > + mf->field = V4L2_FIELD_INTERLACED; > + mf->colorspace = 0; I'd just use what the user provided. > + > + if (format->which != V4L2_SUBDEV_FORMAT_TRY) { > + ret = isl7998x_update_std(isl7998x); > + if (ret) > + return ret; > + mf->width = isl7998x->width; > + mf->height = isl7998x->height; > + isl7998x->fmt = &isl7998x_colour_fmts[0]; > + } > + > + return 0; > +} > + > +static int isl7998x_set_test_pattern(struct isl7998x *isl7998x) > +{ > + const struct reg_sequence isl7998x_init_seq_tpg_off[] = { > + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0 } > + }; > + const struct reg_sequence isl7998x_init_seq_tpg_on[] = { > + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, > + isl7998x->test_pattern_bars << 6 }, > + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, > + isl7998x->test_pattern_enabled == 1 ? BIT(2) : 0 }, > + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, > + (isl7998x->test_pattern_chans << 4) | > + (isl7998x->test_pattern_color << 2) } > + }; > + struct regmap *regmap = isl7998x->regmap; > + > + if (isl7998x->test_pattern_enabled) { > + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_on, > + ARRAY_SIZE(isl7998x_init_seq_tpg_on)); > + } else { > + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_off, > + ARRAY_SIZE(isl7998x_init_seq_tpg_off)); > + } No need for braces. > +} > + > +static int isl7998x_set_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct isl7998x *isl7998x = container_of(ctrl->handler, > + struct isl7998x, ctrl_handler); > + > + switch (ctrl->id) { > + case V4L2_CID_TEST_PATTERN_BARS: > + isl7998x->test_pattern_bars = ctrl->val & 0x3; > + return isl7998x_set_test_pattern(isl7998x); > + case V4L2_CID_TEST_PATTERN_CHANNELS: > + isl7998x->test_pattern_chans = ctrl->val & 0xf; > + return isl7998x_set_test_pattern(isl7998x); > + case V4L2_CID_TEST_PATTERN_COLOR: > + isl7998x->test_pattern_color = ctrl->val & 0x3; > + return isl7998x_set_test_pattern(isl7998x); > + case V4L2_CID_TEST_PATTERN: > + isl7998x->test_pattern_enabled = !!ctrl->val; > + return isl7998x_set_test_pattern(isl7998x); It'd simplify the driver to use the control value in isl7998x_set_test_pattern() without storing the intermediate result in driver's own struct. > + } > + > + return 0; > +} > + > +static int isl7998x_get_ctrl(struct v4l2_ctrl *ctrl) > +{ > + struct isl7998x *isl7998x = container_of(ctrl->handler, > + struct isl7998x, ctrl_handler); > + > + v4l2_info(&isl7998x->subdev, "ctrl(id:0x%x,val:0x%x) is not handled\n", > + ctrl->id, ctrl->val); If you have no volatile controls, you can omit this function. > + > + return 0; > +} > + > +static const struct v4l2_subdev_video_ops isl7998x_subdev_video_ops = { > + .g_mbus_config = isl7998x_g_mbus_config, > + .s_stream = isl7998x_s_stream, > +}; > + > +static const struct v4l2_subdev_pad_ops isl7998x_subdev_pad_ops = { > + .enum_mbus_code = isl7998x_enum_mbus_code, > + .get_fmt = isl7998x_get_fmt, > + .set_fmt = isl7998x_set_fmt, > +}; > + > +static const struct v4l2_subdev_ops isl7998x_subdev_ops = { > + .video = &isl7998x_subdev_video_ops, > + .pad = &isl7998x_subdev_pad_ops, > +}; > + > +static const struct media_entity_operations isl7998x_entity_ops = { > + .link_validate = v4l2_subdev_link_validate, > +}; > + > +static const struct v4l2_ctrl_ops isl7998x_ctrl_ops = { > + .s_ctrl = isl7998x_set_ctrl, > + .g_volatile_ctrl = isl7998x_get_ctrl, > +}; > + > +static const char * const isl7998x_test_pattern_bars[] = { > + "bbbbwb", "bbbwwb", "bbwbwb", "bbwwwb" > +}; > + > +static const char * const isl7998x_test_pattern_colors[] = { > + "Yellow", "Blue", "Green", "Pink" > +}; > + > +static const struct v4l2_ctrl_config isl7998x_ctrls[] = { > + { > + .ops = &isl7998x_ctrl_ops, > + .id = V4L2_CID_TEST_PATTERN_BARS, > + .type = V4L2_CTRL_TYPE_MENU, > + .name = "Test Pattern Bars", > + .max = ARRAY_SIZE(isl7998x_test_pattern_bars) - 1, > + .def = 0, > + .qmenu = isl7998x_test_pattern_bars, > + }, { > + .ops = &isl7998x_ctrl_ops, > + .id = V4L2_CID_TEST_PATTERN_CHANNELS, > + .type = V4L2_CTRL_TYPE_INTEGER, > + .name = "Test Pattern Channels", > + .min = 0, > + .max = 0xf, > + .step = 1, > + .def = 0, > + .flags = 0, > + }, { > + .ops = &isl7998x_ctrl_ops, > + .id = V4L2_CID_TEST_PATTERN_COLOR, > + .type = V4L2_CTRL_TYPE_MENU, > + .name = "Test Pattern Color", > + .max = ARRAY_SIZE(isl7998x_test_pattern_colors) - 1, > + .def = 0, > + .qmenu = isl7998x_test_pattern_colors, > + }, > +}; > + > +#define ISL7998x_REG_DECODER_ACA_READABLE_RANGE(page) \ > + /* Decoder range */ \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ > + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ > + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ > + ISL7998x_REG_Px_DEC_HUE(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ > + ISL7998x_REG_Px_DEC_CORING(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > + ISL7998x_REG_Px_DEC_SDTR(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ > + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ > + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ > + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ > + /* ACA range */ \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ > + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ > + ISL7998x_REG_Px_ACA_CTL_4(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ > + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ > + ISL7998x_REG_Px_DEC_PAGE(page)) > + > +#define ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(page) \ > + /* Decoder range */ \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INPUT_FMT(page), \ > + ISL7998x_REG_Px_DEC_INPUT_FMT(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page), \ > + ISL7998x_REG_Px_DEC_HS_DELAY_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_ANCTL(page), \ > + ISL7998x_REG_Px_DEC_CSC_CTL(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_BRIGHT(page), \ > + ISL7998x_REG_Px_DEC_HUE(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_VERT_PEAK(page), \ > + ISL7998x_REG_Px_DEC_CORING(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > + ISL7998x_REG_Px_DEC_SDTR(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMPG(page), \ > + ISL7998x_REG_Px_DEC_MISC3(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_CLMD(page), \ > + ISL7998x_REG_Px_DEC_DATA_CONV(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_INTERNAL_TEST(page), \ > + ISL7998x_REG_Px_DEC_INTERNAL_TEST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_H_DELAY_CTL(page), \ > + ISL7998x_REG_Px_DEC_H_DELAY_II_LOW(page)), \ > + /* ACA range */ \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_1(page), \ > + ISL7998x_REG_Px_ACA_HIST_WIN_V_SZ2(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_CTL_2(page), \ > + ISL7998x_REG_Px_ACA_CTL_4(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_FLEX_WIN_HIST(page), \ > + ISL7998x_REG_Px_ACA_HIST_DATA_LO(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page), \ > + ISL7998x_REG_Px_ACA_XFER_HIST_HOST(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(page), \ > + ISL7998x_REG_Px_DEC_PAGE(page)) > + > +#define ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(page) \ > + /* Decoder range */ \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_STATUS_1(page), \ > + ISL7998x_REG_Px_DEC_STATUS_1(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_SDT(page), \ > + ISL7998x_REG_Px_DEC_SDT(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_DEC_MVSN(page), \ > + ISL7998x_REG_Px_DEC_HFREF(page)), \ > + /* ACA range */ \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_Y_AVG(page), \ > + ISL7998x_REG_Px_ACA_Y_HIGH(page)), \ > + regmap_reg_range(ISL7998x_REG_Px_ACA_HIST_DATA_LO(page), \ > + ISL7998x_REG_Px_ACA_FLEX_WIN_CR_CLR(page)) > + > +static const struct regmap_range isl7998x_readable_ranges[] = { > + regmap_reg_range(ISL7998x_REG_P0_PRODUCT_ID_CODE, > + ISL7998x_REG_P0_IRQ_SYNC_CTL), > + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, > + ISL7998x_REG_P0_CLOCK_DELAY), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), > + ISL7998x_REG_Px_DEC_PAGE(0)), > + > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(1), > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(2), > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(3), > + ISL7998x_REG_DECODER_ACA_READABLE_RANGE(4), > + > + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, > + ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL), > + regmap_reg_range(ISL7998x_REG_P5_FIFO_THRSH_CNT_1, > + ISL7998x_REG_P5_PLL_ANA), > + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, > + ISL7998x_REG_P5_HIST_LINE_CNT_2), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), > + ISL7998x_REG_Px_DEC_PAGE(5)), > +}; > + > +static const struct regmap_range isl7998x_writeable_ranges[] = { > + regmap_reg_range(ISL7998x_REG_P0_SW_RESET_CTL, > + ISL7998x_REG_P0_IRQ_SYNC_CTL), > + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_IRQ, > + ISL7998x_REG_P0_SHORT_DIAG_IRQ_EN), > + regmap_reg_range(ISL7998x_REG_P0_CLOCK_DELAY, > + ISL7998x_REG_P0_CLOCK_DELAY), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(0), > + ISL7998x_REG_Px_DEC_PAGE(0)), > + > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(1), > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(2), > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(3), > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(4), > + > + regmap_reg_range(ISL7998x_REG_P5_LI_ENGINE_CTL, > + ISL7998x_REG_P5_ESC_MODE_TIME_CTL), > + regmap_reg_range(ISL7998x_REG_P5_MIPI_SP_HS_TRL_CTL, > + ISL7998x_REG_P5_PLL_ANA), > + regmap_reg_range(ISL7998x_REG_P5_TOTAL_PF_LINE_CNT_1, > + ISL7998x_REG_P5_HIST_LINE_CNT_2), > + regmap_reg_range(ISL7998x_REG_Px_DEC_PAGE(5), > + ISL7998x_REG_Px_DEC_PAGE(5)), > + > + ISL7998x_REG_DECODER_ACA_WRITEABLE_RANGE(0xf), > +}; > + > +static const struct regmap_range isl7998x_volatile_ranges[] = { > + regmap_reg_range(ISL7998x_REG_P0_MPP1_SYNC_CTL, > + ISL7998x_REG_P0_IRQ_SYNC_CTL), > + regmap_reg_range(ISL7998x_REG_P0_INTERRUPT_STATUS, > + ISL7998x_REG_P0_INTERRUPT_STATUS), > + regmap_reg_range(ISL7998x_REG_P0_CHAN_1_STATUS, > + ISL7998x_REG_P0_SHORT_DIAG_STATUS), > + > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(1), > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(2), > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(3), > + ISL7998x_REG_DECODER_ACA_VOLATILE_RANGE(4), > + > + regmap_reg_range(ISL7998x_REG_P5_AUTO_TEST_ERR_DET, > + ISL7998x_REG_P5_PIC_HEIGHT_LOW), > +}; > + > +static const struct regmap_access_table isl7998x_readable_table = { > + .yes_ranges = isl7998x_readable_ranges, > + .n_yes_ranges = ARRAY_SIZE(isl7998x_readable_ranges), > +}; > + > +static const struct regmap_access_table isl7998x_writeable_table = { > + .yes_ranges = isl7998x_writeable_ranges, > + .n_yes_ranges = ARRAY_SIZE(isl7998x_writeable_ranges), > +}; > + > +static const struct regmap_access_table isl7998x_volatile_table = { > + .yes_ranges = isl7998x_volatile_ranges, > + .n_yes_ranges = ARRAY_SIZE(isl7998x_volatile_ranges), > +}; > + > +static const struct regmap_range_cfg isl7998x_ranges[] = { > + { > + .range_min = ISL7998x_REG_Pn_BASE(0), > + .range_max = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), > + .selector_reg = ISL7998x_REG_Px_DEC_PAGE(0), > + .selector_mask = ISL7998x_REG_Px_DEC_PAGE_MASK, > + .window_start = 0, > + .window_len = 256, > + } > +}; > + > +static const struct regmap_config isl7998x_regmap = { > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = ISL7998x_REG_Px_ACA_XFER_HIST_HOST(0xf), > + .ranges = isl7998x_ranges, > + .num_ranges = ARRAY_SIZE(isl7998x_ranges), > + .rd_table = &isl7998x_readable_table, > + .wr_table = &isl7998x_writeable_table, > + .volatile_table = &isl7998x_volatile_table, > + .cache_type = REGCACHE_RBTREE, > +}; > + > +static int isl7998x_probe(struct i2c_client *client, > + const struct i2c_device_id *did) > +{ > + struct device *dev = &client->dev; > + struct v4l2_fwnode_endpoint endpoint; Please do initialise the bus_type field at least. > + struct device_node *ep; > + struct isl7998x *isl7998x; > + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent); > + u32 chip_id; > + int i, ret; > + > + ret = i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA); > + if (!ret) { > + dev_warn(&adapter->dev, > + "I2C-Adapter doesn't support I2C_FUNC_SMBUS_WORD\n"); > + return -EIO; > + } > + > + isl7998x = devm_kzalloc(dev, sizeof(*isl7998x), GFP_KERNEL); > + if (!isl7998x) > + return -ENOMEM; > + > + /* Default to all four inputs active unless specified otherwise. */ > + ret = of_property_read_u32(dev->of_node, "isil,num-inputs", > + &isl7998x->nr_inputs); > + if (ret) > + isl7998x->nr_inputs = 4; > + > + if (isl7998x->nr_inputs != 1 && isl7998x->nr_inputs != 2 && > + isl7998x->nr_inputs != 4) { > + dev_err(dev, "Invalid number of inputs selected in DT\n"); > + return -EINVAL; > + } > + > + isl7998x->pd_gpio = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); > + if (IS_ERR(isl7998x->pd_gpio)) { > + dev_err(dev, "Failed to retrieve/request PD GPIO: %ld\n", > + PTR_ERR(isl7998x->pd_gpio)); > + return PTR_ERR(isl7998x->pd_gpio); > + } > + > + isl7998x->regmap = devm_regmap_init_i2c(client, &isl7998x_regmap); > + if (IS_ERR(isl7998x->regmap)) { > + ret = PTR_ERR(isl7998x->regmap); > + dev_err(dev, "Failed to allocate register map: %d\n", ret); > + return ret; > + } > + > + ep = of_graph_get_next_endpoint(dev->of_node, NULL); > + if (!ep) { > + dev_err(dev, "Missing endpoint node\n"); > + return -EINVAL; > + } > + > + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &endpoint); > + of_node_put(ep); > + if (ret) { > + dev_err(dev, "Failed to parse endpoint\n"); > + return ret; > + } > + > + if (endpoint.bus_type != V4L2_MBUS_CSI2_DPHY || > + endpoint.bus.mipi_csi2.num_data_lanes == 0 || > + endpoint.bus.mipi_csi2.num_data_lanes > 2) { > + dev_err(dev, "Invalid bus type or number of MIPI lanes\n"); > + return -EINVAL; > + } > + > + isl7998x->nr_mipi_lanes = endpoint.bus.mipi_csi2.num_data_lanes; > + > + v4l2_i2c_subdev_init(&isl7998x->subdev, client, &isl7998x_subdev_ops); > + isl7998x->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; > + > +#ifdef CONFIG_MEDIA_CONTROLLER > + isl7998x->pad.flags = MEDIA_PAD_FL_SOURCE; > + isl7998x->subdev.entity.ops = &isl7998x_entity_ops; > + isl7998x->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; This is definitely not a camera sensor. MEDIA_ENT_F_VID_IF_BRIDGE perhaps? How does the driver work without MC? E.g. how are the formats on the inputs set up? > + ret = media_entity_pads_init(&isl7998x->subdev.entity, 1, > + &isl7998x->pad); > + if (ret < 0) > + return ret; > +#endif > + > + isl7998x->width = ISL7998x_WIDTH; > + isl7998x->height = ISL7998x_HEIGHT; > + isl7998x->fmt = &isl7998x_colour_fmts[0]; > + > + ret = v4l2_ctrl_handler_init(&isl7998x->ctrl_handler, > + 2 + ARRAY_SIZE(isl7998x_ctrls)); > + if (ret) > + return ret; > + > + mutex_init(&isl7998x->ctrl_mutex); > + isl7998x->ctrl_handler.lock = &isl7998x->ctrl_mutex; > + isl7998x->link_freq = v4l2_ctrl_new_int_menu(&isl7998x->ctrl_handler, > + &isl7998x_ctrl_ops, V4L2_CID_LINK_FREQ, > + ARRAY_SIZE(link_freq_menu_items) - 1, > + endpoint.bus.mipi_csi2.num_data_lanes == 2 ? > + 1 : 0, link_freq_menu_items); > + isl7998x->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; Note that v4l2_ctrl_new_int_menu() returns NULL on error. Please also check the control handler's error status when you're done setting up controls, and call v4l2_ctrl_handler_free() in cleanup if there was an error. > + > + for (i = 0; i < ARRAY_SIZE(isl7998x_ctrls); i++) { > + v4l2_ctrl_new_custom(&isl7998x->ctrl_handler, > + &isl7998x_ctrls[i], NULL); > + } No need for braces. > + > + v4l2_ctrl_new_std_menu_items(&isl7998x->ctrl_handler, > + &isl7998x_ctrl_ops, V4L2_CID_TEST_PATTERN, > + ARRAY_SIZE(isl7998x_test_pattern_menu) - 1, > + 0, 0, isl7998x_test_pattern_menu); > + > + isl7998x->subdev.ctrl_handler = &isl7998x->ctrl_handler; > + > + isl7998x->subdev.dev = dev; The dev field is initialised to the same value by v4l2_i2c_subdev_init(). Please remove. > + ret = v4l2_async_register_subdev(&isl7998x->subdev); > + if (ret < 0) > + goto err_entity_cleanup; > + > + /* > + * Turn the chip ON and keep it ON, otherwise the camera standard > + * detection takes about 600 mS every time we do VIDIOC_G_FMT. "ms". Unless you meant Siemens, a unit of conductance. > + */ > + if (isl7998x->pd_gpio) > + gpiod_set_value(isl7998x->pd_gpio, 0); > + > + ret = regmap_read(isl7998x->regmap, ISL7998x_REG_P0_PRODUCT_ID_CODE, > + &chip_id); > + if (ret) { > + dev_err(dev, "Failed to read ID register: %d\n", ret); > + goto err_init_cleanup; > + } > + > + dev_info(dev, "ISL7998x found (id=%x)\n", chip_id); > + > + ret = isl7998x_init(isl7998x); > + if (ret) > + goto err_init_cleanup; > + > + ret = isl7998x_update_std(isl7998x); > + if (ret) > + goto err_init_cleanup; > + > + return 0; > + > +err_init_cleanup: > + if (isl7998x->pd_gpio) > + gpiod_set_value(isl7998x->pd_gpio, 1); > +err_entity_cleanup: > +#ifdef CONFIG_MEDIA_CONTROLLER > + media_entity_cleanup(&isl7998x->subdev.entity); > +#endif You can remove the #ifdef here. Newlines are nice before labels and return (unless it's right after if). > + return ret; > +} > + > +static int isl7998x_remove(struct i2c_client *client) > +{ > + struct isl7998x *isl7998x = i2c_to_isl7998x(client); > + > + if (isl7998x->pd_gpio) > + gpiod_set_value(isl7998x->pd_gpio, 1); > + v4l2_async_unregister_subdev(&isl7998x->subdev); > + v4l2_ctrl_handler_free(isl7998x->subdev.ctrl_handler); > + media_entity_cleanup(&isl7998x->subdev.entity); > + > + return 0; > +} > + > +static const struct of_device_id isl7998x_of_match[] = { > + { .compatible = "isil,isl79987", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, isl7998x_of_match); > + > +static const struct i2c_device_id isl7998x_id[] = { > + { "isl79987", 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, isl7998x_id); > + > +static struct i2c_driver isl7998x_i2c_driver = { > + .driver = { > + .name = "isl7998x", > + .of_match_table = of_match_ptr(isl7998x_of_match), > + }, > + .probe = isl7998x_probe, > + .remove = isl7998x_remove, > + .id_table = isl7998x_id, Use probe_new, and you can omit the id_table. > +}; > + > +module_i2c_driver(isl7998x_i2c_driver); > + > +MODULE_DESCRIPTION("Intersil ISL7998x BT656-to-MIPI-CSI2 driver"); > +MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); > +MODULE_LICENSE("GPL"); The SPDX header indicates GPL v2.0. Which one is correct? -- Kind regards, Sakari Ailus sakari.ailus@linux.intel.com ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x 2019-07-01 8:43 ` Sakari Ailus @ 2019-08-06 14:25 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2019-08-06 14:25 UTC (permalink / raw) To: Sakari Ailus; +Cc: linux-media, Mauro Carvalho Chehab, Rob Herring On 7/1/19 10:43 AM, Sakari Ailus wrote: [...] >> + { ISL7998x_REG_P0_CLK_CTL_1, 0x1f }, >> + { ISL7998x_REG_P0_CLK_CTL_2, 0x43 }, >> + { ISL7998x_REG_P0_CLK_CTL_3, 0x4f }, > > It'd be great to see what these magical numbers signify. How about some > additional #defines for the bits? Same below. That would mean mindlessly transcribing big part of the datasheet here, but I think it would add very little value, except for another level of obfuscation. If anyone ever needs to tweak anything here , they would have a datasheet along with it anyway. [...] >> + >> +/* Menu items for LINK_FREQ V4L2 control */ >> +static const s64 link_freq_menu_items[] = { >> + 108000000, 216000000, 432000000 >> +}; > > Where to these numbers come from? The datasheet, these are the mipi csi2 link frequencies. >> + >> +/* Menu items for TEST_PATTERN V4L2 control */ >> +static const char * const isl7998x_test_pattern_menu[] = { >> + "Disabled", "Enabled-PAL (720x576)", "Enabled-NTSC (720x480)" >> +}; >> + >> +struct isl7998x { >> + struct v4l2_subdev subdev; >> + struct regmap *regmap; >> + struct gpio_desc *pd_gpio; >> + unsigned int nr_mipi_lanes; >> + u32 nr_inputs; >> + >> + unsigned int width; >> + unsigned int height; >> + const struct isl7998x_datafmt *fmt; >> +#ifdef CONFIG_MEDIA_CONTROLLER >> + struct media_pad pad; > > Hmm. Didn't you have four inputs in your device? Yes, this is the output (mipi csi2) pad. There is only one. > >> +#endif >> + >> + struct v4l2_ctrl_handler ctrl_handler; >> + struct mutex ctrl_mutex; >> + /* V4L2 Controls */ >> + struct v4l2_ctrl *link_freq; >> + u8 test_pattern_enabled; >> + u8 test_pattern_bars; >> + u8 test_pattern_chans; >> + u8 test_pattern_color; >> +}; >> + >> +static struct isl7998x *sd_to_isl7998x(struct v4l2_subdev *sd) >> +{ >> + return container_of(sd, struct isl7998x, subdev); >> +} >> + >> +static struct isl7998x *i2c_to_isl7998x(const struct i2c_client *client) >> +{ >> + return sd_to_isl7998x(i2c_get_clientdata(client)); >> +} >> + >> +static int isl7998x_init(struct isl7998x *isl7998x) >> +{ >> + const unsigned int lanes = isl7998x->nr_mipi_lanes; >> + const u32 isl7998x_video_in_chan_map[] = { 0x00, 0x11, 0x02, 0x02 }; >> + const struct reg_sequence isl7998x_init_seq_custom[] = { >> + { ISL7998x_REG_P0_VIDEO_IN_CHAN_CTL, >> + isl7998x_video_in_chan_map[isl7998x->nr_inputs - 1] }, >> + { ISL7998x_REG_P0_CLK_CTL_4, (lanes == 1) ? 0x40 : 0x41 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL, (lanes == 1) ? 0x01 : 0x02 }, >> + { ISL7998x_REG_P5_LI_ENGINE_LINE_CTL, >> + 0x20 | ((isl7998x->width >> 7) & 0x1f) }, >> + { ISL7998x_REG_P5_LI_ENGINE_PIC_WIDTH, >> + (isl7998x->width << 1) & 0xff }, >> + }; >> + struct regmap *regmap = isl7998x->regmap; >> + int ret; >> + >> + ret = regmap_register_patch(regmap, isl7998x_init_seq_1, >> + ARRAY_SIZE(isl7998x_init_seq_1)); >> + if (ret) >> + return ret; >> + >> + ret = regmap_register_patch(regmap, isl7998x_init_seq_custom, >> + ARRAY_SIZE(isl7998x_init_seq_custom)); >> + if (ret) >> + return ret; >> + >> + return regmap_register_patch(regmap, isl7998x_init_seq_2, >> + ARRAY_SIZE(isl7998x_init_seq_2)); >> +} >> + >> +static int isl7998x_g_mbus_config(struct v4l2_subdev *sd, >> + struct v4l2_mbus_config *cfg) >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + >> + cfg->type = V4L2_MBUS_CSI2_DPHY; >> + cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; >> + if (isl7998x->nr_mipi_lanes == 1) >> + cfg->flags |= V4L2_MBUS_CSI2_1_LANE; >> + else >> + cfg->flags |= V4L2_MBUS_CSI2_2_LANE; > > Drivers nowadays generally get this from DT. You can omit this function > safely. For dynamic configuration we'll need something else (Jacopo's been > working on that with me). So how else would I configure my MIPI CSI2 receiver ? I presume the iMX6 CSI2 driver needs to be updated somehow ? >> + >> + return 0; >> +} >> + >> +static int isl7998x_s_stream(struct v4l2_subdev *sd, int enable) >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + >> + return isl7998x_init(isl7998x); > > Is this needed both to initialise the hardware as well as start streaming? Yes, otherwise the csi2 link is unstable. > Does this also enable the CSI-2 transmitter in driver's probe? This could > be problematic for some receivers. How so ? >> +} >> + >> +static int isl7998x_enum_mbus_code(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_mbus_code_enum *code) >> +{ >> + if (code->pad || code->index >= ARRAY_SIZE(isl7998x_colour_fmts)) >> + return -EINVAL; >> + >> + code->code = isl7998x_colour_fmts[code->index].code; > > A newline would be nice here. > >> + return 0; >> +} >> + >> +static const unsigned int isl7998x_std_res[] = { >> + 480, 576, 576, 480, 480, 576, 480, 480 >> +}; >> + >> +static int isl7998x_update_std(struct isl7998x *isl7998x) >> +{ >> + unsigned int height[ISL7998x_INPUTS]; >> + u8 scanning = GENMASK(ISL7998x_INPUTS - 1, 0); >> + unsigned int i; >> + int ret; >> + u32 reg; >> + >> + while (true) { >> + for (i = 0; i < ISL7998x_INPUTS; i++) { >> + ret = regmap_read(isl7998x->regmap, >> + ISL7998x_REG_Px_DEC_SDT(i + 1), ®); >> + if (ret) >> + return ret; >> + >> + /* Detection is still in progress, restart. */ >> + if (reg & ISL7998x_REG_Px_DEC_SDT_DET) { >> + scanning = GENMASK(ISL7998x_INPUTS - 1, 0); >> + break; >> + } >> + >> + scanning &= ~BIT(i); >> + height[i] = isl7998x_std_res[(reg >> 4) & 0x7]; >> + } >> + >> + if (!scanning) >> + break; >> + >> + mdelay(1); > > How long does this take in general? Could you use msleep() instead of > mdelay() in order to avoid a busy loop at least seemingly of unknown > length? I changed it to usleep_range() >> + } >> + >> + /* >> + * According to Renesas FAE, all input cameras must have the >> + * same standard on this chip. >> + */ >> + for (i = 1; i < isl7998x->nr_inputs ; i++) >> + if (height[i - 1] != height[i]) >> + return -EINVAL; >> + >> + isl7998x->height = height[0]; >> + >> + return 0; >> +} >> + >> +static int isl7998x_get_fmt(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *format) >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + struct v4l2_mbus_framefmt *mf = &format->format; >> + >> + if (format->pad != 0) >> + return -EINVAL; >> + >> + if (isl7998x->test_pattern_enabled == 1) { >> + mf->width = 720; >> + mf->height = 576; >> + } else if (isl7998x->test_pattern_enabled == 2) { >> + mf->width = 720; >> + mf->height = 480; >> + } else { >> + mf->width = isl7998x->width; >> + mf->height = isl7998x->height; >> + } >> + >> + mf->code = isl7998x->fmt->code; >> + mf->field = V4L2_FIELD_INTERLACED; >> + mf->colorspace = 0; >> + >> + return 0; >> +} >> + >> +static int isl7998x_set_fmt(struct v4l2_subdev *sd, >> + struct v4l2_subdev_pad_config *cfg, >> + struct v4l2_subdev_format *format) >> +{ >> + struct isl7998x *isl7998x = sd_to_isl7998x(sd); >> + struct v4l2_mbus_framefmt *mf = &format->format; >> + int ret; >> + >> + if (format->pad != 0) >> + return -EINVAL; > > You can omit the pad checks in pad ops; the framework does that nowadays. OK >> + >> + if (format->format.width != 720 || >> + (format->format.height != 480 && format->format.height != 576)) >> + return -EINVAL; >> + >> + if (format->format.code != MEDIA_BUS_FMT_YUYV8_2X8) >> + return -EINVAL; > > Instead of returning an error, you should simply pick a valid format if the > user-supplied format (mbus code, size) isn't supported. > >> + >> + mf->width = format->format.width; >> + mf->height = format->format.height; >> + mf->code = format->format.code; >> + mf->field = V4L2_FIELD_INTERLACED; >> + mf->colorspace = 0; > > I'd just use what the user provided. How can that even work ? The hardware might not support that. >> + >> + if (format->which != V4L2_SUBDEV_FORMAT_TRY) { >> + ret = isl7998x_update_std(isl7998x); >> + if (ret) >> + return ret; >> + mf->width = isl7998x->width; >> + mf->height = isl7998x->height; >> + isl7998x->fmt = &isl7998x_colour_fmts[0]; >> + } >> + >> + return 0; >> +} >> + >> +static int isl7998x_set_test_pattern(struct isl7998x *isl7998x) >> +{ >> + const struct reg_sequence isl7998x_init_seq_tpg_off[] = { >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, 0 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, 0 } >> + }; >> + const struct reg_sequence isl7998x_init_seq_tpg_on[] = { >> + { ISL7998x_REG_P5_TP_GEN_BAR_PATTERN, >> + isl7998x->test_pattern_bars << 6 }, >> + { ISL7998x_REG_P5_LI_ENGINE_CTL_2, >> + isl7998x->test_pattern_enabled == 1 ? BIT(2) : 0 }, >> + { ISL7998x_REG_P5_LI_ENGINE_TP_GEN_CTL, >> + (isl7998x->test_pattern_chans << 4) | >> + (isl7998x->test_pattern_color << 2) } >> + }; >> + struct regmap *regmap = isl7998x->regmap; >> + >> + if (isl7998x->test_pattern_enabled) { >> + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_on, >> + ARRAY_SIZE(isl7998x_init_seq_tpg_on)); >> + } else { >> + return regmap_register_patch(regmap, isl7998x_init_seq_tpg_off, >> + ARRAY_SIZE(isl7998x_init_seq_tpg_off)); >> + } > > No need for braces. I believe they are required by checkpatch for multiline conditionals. >> +} >> + >> +static int isl7998x_set_ctrl(struct v4l2_ctrl *ctrl) >> +{ >> + struct isl7998x *isl7998x = container_of(ctrl->handler, >> + struct isl7998x, ctrl_handler); >> + >> + switch (ctrl->id) { >> + case V4L2_CID_TEST_PATTERN_BARS: >> + isl7998x->test_pattern_bars = ctrl->val & 0x3; >> + return isl7998x_set_test_pattern(isl7998x); >> + case V4L2_CID_TEST_PATTERN_CHANNELS: >> + isl7998x->test_pattern_chans = ctrl->val & 0xf; >> + return isl7998x_set_test_pattern(isl7998x); >> + case V4L2_CID_TEST_PATTERN_COLOR: >> + isl7998x->test_pattern_color = ctrl->val & 0x3; >> + return isl7998x_set_test_pattern(isl7998x); >> + case V4L2_CID_TEST_PATTERN: >> + isl7998x->test_pattern_enabled = !!ctrl->val; >> + return isl7998x_set_test_pattern(isl7998x); > > It'd simplify the driver to use the control value in > isl7998x_set_test_pattern() without storing the intermediate result in > driver's own struct. You need to keep track of which controls are set and how , which is why they are stored in the drivers' private data. >> + } >> + >> + return 0; >> +} >> + >> +static int isl7998x_get_ctrl(struct v4l2_ctrl *ctrl) >> +{ >> + struct isl7998x *isl7998x = container_of(ctrl->handler, >> + struct isl7998x, ctrl_handler); >> + >> + v4l2_info(&isl7998x->subdev, "ctrl(id:0x%x,val:0x%x) is not handled\n", >> + ctrl->id, ctrl->val); > > If you have no volatile controls, you can omit this function. OK [...] >> +static int isl7998x_probe(struct i2c_client *client, >> + const struct i2c_device_id *did) >> +{ >> + struct device *dev = &client->dev; >> + struct v4l2_fwnode_endpoint endpoint; > > Please do initialise the bus_type field at least. v4l2_fwnode_endpoint_parse() should do that, right ? >> + struct device_node *ep; >> + struct isl7998x *isl7998x; >> + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent); >> + u32 chip_id; >> + int i, ret; >> + >> + ret = i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA); >> + if (!ret) { >> + dev_warn(&adapter->dev, >> + "I2C-Adapter doesn't support I2C_FUNC_SMBUS_WORD\n"); >> + return -EIO; >> + } >> + >> + isl7998x = devm_kzalloc(dev, sizeof(*isl7998x), GFP_KERNEL); >> + if (!isl7998x) >> + return -ENOMEM; >> + >> + /* Default to all four inputs active unless specified otherwise. */ >> + ret = of_property_read_u32(dev->of_node, "isil,num-inputs", >> + &isl7998x->nr_inputs); >> + if (ret) >> + isl7998x->nr_inputs = 4; >> + >> + if (isl7998x->nr_inputs != 1 && isl7998x->nr_inputs != 2 && >> + isl7998x->nr_inputs != 4) { >> + dev_err(dev, "Invalid number of inputs selected in DT\n"); >> + return -EINVAL; >> + } >> + >> + isl7998x->pd_gpio = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); >> + if (IS_ERR(isl7998x->pd_gpio)) { >> + dev_err(dev, "Failed to retrieve/request PD GPIO: %ld\n", >> + PTR_ERR(isl7998x->pd_gpio)); >> + return PTR_ERR(isl7998x->pd_gpio); >> + } >> + >> + isl7998x->regmap = devm_regmap_init_i2c(client, &isl7998x_regmap); >> + if (IS_ERR(isl7998x->regmap)) { >> + ret = PTR_ERR(isl7998x->regmap); >> + dev_err(dev, "Failed to allocate register map: %d\n", ret); >> + return ret; >> + } >> + >> + ep = of_graph_get_next_endpoint(dev->of_node, NULL); >> + if (!ep) { >> + dev_err(dev, "Missing endpoint node\n"); >> + return -EINVAL; >> + } >> + >> + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &endpoint); >> + of_node_put(ep); >> + if (ret) { >> + dev_err(dev, "Failed to parse endpoint\n"); >> + return ret; >> + } >> + >> + if (endpoint.bus_type != V4L2_MBUS_CSI2_DPHY || >> + endpoint.bus.mipi_csi2.num_data_lanes == 0 || >> + endpoint.bus.mipi_csi2.num_data_lanes > 2) { >> + dev_err(dev, "Invalid bus type or number of MIPI lanes\n"); >> + return -EINVAL; >> + } >> + >> + isl7998x->nr_mipi_lanes = endpoint.bus.mipi_csi2.num_data_lanes; >> + >> + v4l2_i2c_subdev_init(&isl7998x->subdev, client, &isl7998x_subdev_ops); >> + isl7998x->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; >> + >> +#ifdef CONFIG_MEDIA_CONTROLLER >> + isl7998x->pad.flags = MEDIA_PAD_FL_SOURCE; >> + isl7998x->subdev.entity.ops = &isl7998x_entity_ops; >> + isl7998x->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; > > This is definitely not a camera sensor. > > MEDIA_ENT_F_VID_IF_BRIDGE perhaps? > > How does the driver work without MC? MC ? > E.g. how are the formats on the inputs set up? They are auto-detected by the chip. [...] -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x 2019-05-20 20:18 ` [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x Marek Vasut 2019-07-01 7:58 ` Jacopo Mondi 2019-07-01 8:43 ` Sakari Ailus @ 2019-07-01 8:46 ` Sakari Ailus 2 siblings, 0 replies; 22+ messages in thread From: Sakari Ailus @ 2019-07-01 8:46 UTC (permalink / raw) To: Marek Vasut; +Cc: linux-media, Mauro Carvalho Chehab, Rob Herring One more comment... On Mon, May 20, 2019 at 10:18:12PM +0200, Marek Vasut wrote: ... > +static int isl7998x_set_fmt(struct v4l2_subdev *sd, > + struct v4l2_subdev_pad_config *cfg, > + struct v4l2_subdev_format *format) > +{ > + struct isl7998x *isl7998x = sd_to_isl7998x(sd); > + struct v4l2_mbus_framefmt *mf = &format->format; > + int ret; > + > + if (format->pad != 0) > + return -EINVAL; > + > + if (format->format.width != 720 || > + (format->format.height != 480 && format->format.height != 576)) > + return -EINVAL; > + > + if (format->format.code != MEDIA_BUS_FMT_YUYV8_2X8) > + return -EINVAL; > + > + mf->width = format->format.width; > + mf->height = format->format.height; > + mf->code = format->format.code; > + mf->field = V4L2_FIELD_INTERLACED; > + mf->colorspace = 0; > + > + if (format->which != V4L2_SUBDEV_FORMAT_TRY) { > + ret = isl7998x_update_std(isl7998x); > + if (ret) > + return ret; > + mf->width = isl7998x->width; > + mf->height = isl7998x->height; > + isl7998x->fmt = &isl7998x_colour_fmts[0]; > + } Note that as the driver exposes a sub-device node to the user space, it's responsible for serialising the access to its own data structures that are accessed by other drivers or through its uAPI nodes. Most drivers use the same mutex as the control handler, as controls usually deal with at least some of the same data. -- Regards, Sakari Ailus sakari.ailus@linux.intel.com ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-20 20:18 [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Marek Vasut 2019-05-20 20:18 ` [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x Marek Vasut @ 2019-05-28 11:47 ` Jacopo Mondi 2019-05-28 14:36 ` Marek Vasut 2019-07-01 8:04 ` Sakari Ailus 2 siblings, 1 reply; 22+ messages in thread From: Jacopo Mondi @ 2019-05-28 11:47 UTC (permalink / raw) To: Marek Vasut Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree [-- Attachment #1: Type: text/plain, Size: 2989 bytes --] Hi Marek, thanks for the patch On Mon, May 20, 2019 at 10:18:11PM +0200, Marek Vasut wrote: > Add bindings for the Intersil ISL7998x BT656-to-MIPI-CSI2 decoder. > > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Sakari Ailus <sakari.ailus@linux.intel.com> > Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: devicetree@vger.kernel.org > To: linux-media@vger.kernel.org > --- > .../bindings/media/i2c/isl7998x.txt | 37 +++++++++++++++++++ > 1 file changed, 37 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/isl7998x.txt > > diff --git a/Documentation/devicetree/bindings/media/i2c/isl7998x.txt b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt > new file mode 100644 > index 000000000000..c21703983360 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt > @@ -0,0 +1,37 @@ > +Intersil ISL7998x BT656-to-MIPI-CSI2 decoder > + > +The Intersil ISL7998x is a BT656-to-MIPI-CSI decoder which, capable of > +receiving up to four analog stream and multiplexing them into up to four > +MIPI CSI2 virtual channels, using one MIPI clock lane and 1/2 data lanes. > + The documentation is not public, so I can only read what's reported on the website and the short public datasheet at [1] From my understanding of the product page, both the ISL79987 and ILS79988 devices support up to 4 analog inputs, and provide a CSI-2 output and a BT656 output respectively. What am I reading wrong ? [1] https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html > +Required Properties: > +- compatible: value should be "isil,isl79987" > +- pd-gpios: a GPIO spec for the Power Down pin (active high) > + > +Option Properties: > +- isil,num-inputs: Number of connected inputs (1, 2 or 4) Can't you derive this from the number of connected input endpoints instead of providing a custom property? > + > +For further reading on port node refer to > +Documentation/devicetree/bindings/media/video-interfaces.txt. > + I think a description of the supported ports and their intended usages is required here. You have up to 4 inputs and 1 output port, how do you expect them to be numbered? is port@4 the last input or the output one? > +Example: > + > + i2c_master { > + isl7998x_mipi@44 { > + compatible = "isil,isl79987"; > + reg = <0x44>; > + isil,num-inputs = <4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_videoadc>; > + pd-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + > + port { > + isl79987_to_mipi_csi2: endpoint { > + remote-endpoint = <&mipi_csi2_in>; > + clock-lanes = <0>; > + data-lanes = <1 2>; > + }; I see from the example you only support one output port? How do you model the input ones. Thanks j > + }; > + }; > + }; > -- > 2.20.1 > [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-28 11:47 ` [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Jacopo Mondi @ 2019-05-28 14:36 ` Marek Vasut 2019-05-28 15:10 ` Jacopo Mondi 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2019-05-28 14:36 UTC (permalink / raw) To: Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree On 5/28/19 1:47 PM, Jacopo Mondi wrote: > Hi Marek, > thanks for the patch Hi, > On Mon, May 20, 2019 at 10:18:11PM +0200, Marek Vasut wrote: >> Add bindings for the Intersil ISL7998x BT656-to-MIPI-CSI2 decoder. >> >> Signed-off-by: Marek Vasut <marex@denx.de> >> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> >> Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> >> Cc: Rob Herring <robh+dt@kernel.org> >> Cc: devicetree@vger.kernel.org >> To: linux-media@vger.kernel.org >> --- >> .../bindings/media/i2c/isl7998x.txt | 37 +++++++++++++++++++ >> 1 file changed, 37 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/media/i2c/isl7998x.txt >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/isl7998x.txt b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt >> new file mode 100644 >> index 000000000000..c21703983360 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt >> @@ -0,0 +1,37 @@ >> +Intersil ISL7998x BT656-to-MIPI-CSI2 decoder >> + >> +The Intersil ISL7998x is a BT656-to-MIPI-CSI decoder which, capable of >> +receiving up to four analog stream and multiplexing them into up to four >> +MIPI CSI2 virtual channels, using one MIPI clock lane and 1/2 data lanes. >> + > > The documentation is not public, so I can only read what's reported on > the website and the short public datasheet at [1] Right > From my understanding of the product page, both the ISL79987 and > ILS79988 devices support up to 4 analog inputs, and provide a CSI-2 > output and a BT656 output respectively. > > What am I reading wrong ? ISL79987 is analog video to mipi csi2 ; I have this chip. ISL79988 is analog video to bt656 ; I don't have this chip. > [1] https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html > >> +Required Properties: >> +- compatible: value should be "isil,isl79987" >> +- pd-gpios: a GPIO spec for the Power Down pin (active high) >> + >> +Option Properties: >> +- isil,num-inputs: Number of connected inputs (1, 2 or 4) > > Can't you derive this from the number of connected input endpoints > instead of providing a custom property? Input endpoints from where ? >> + >> +For further reading on port node refer to >> +Documentation/devicetree/bindings/media/video-interfaces.txt. >> + > > I think a description of the supported ports and their intended > usages is required here. You have up to 4 inputs and 1 output port, > how do you expect them to be numbered? is port@4 the last input or the > output one? The only port is the MIPI CSI2 , see the example below. >> +Example: >> + >> + i2c_master { >> + isl7998x_mipi@44 { >> + compatible = "isil,isl79987"; >> + reg = <0x44>; >> + isil,num-inputs = <4>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_videoadc>; >> + pd-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; >> + status = "okay"; >> + >> + port { >> + isl79987_to_mipi_csi2: endpoint { >> + remote-endpoint = <&mipi_csi2_in>; >> + clock-lanes = <0>; >> + data-lanes = <1 2>; >> + }; > > I see from the example you only support one output port? How do you > model the input ones. I don't . Do we model analog inputs now somehow ? -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-28 14:36 ` Marek Vasut @ 2019-05-28 15:10 ` Jacopo Mondi 2019-05-28 17:49 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Jacopo Mondi @ 2019-05-28 15:10 UTC (permalink / raw) To: Marek Vasut Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree [-- Attachment #1: Type: text/plain, Size: 4679 bytes --] Hi Marek, On Tue, May 28, 2019 at 04:36:27PM +0200, Marek Vasut wrote: > On 5/28/19 1:47 PM, Jacopo Mondi wrote: > > Hi Marek, > > thanks for the patch > > Hi, > > > On Mon, May 20, 2019 at 10:18:11PM +0200, Marek Vasut wrote: > >> Add bindings for the Intersil ISL7998x BT656-to-MIPI-CSI2 decoder. > >> > >> Signed-off-by: Marek Vasut <marex@denx.de> > >> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> > >> Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> > >> Cc: Rob Herring <robh+dt@kernel.org> > >> Cc: devicetree@vger.kernel.org > >> To: linux-media@vger.kernel.org > >> --- > >> .../bindings/media/i2c/isl7998x.txt | 37 +++++++++++++++++++ > >> 1 file changed, 37 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/media/i2c/isl7998x.txt > >> > >> diff --git a/Documentation/devicetree/bindings/media/i2c/isl7998x.txt b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt > >> new file mode 100644 > >> index 000000000000..c21703983360 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt > >> @@ -0,0 +1,37 @@ > >> +Intersil ISL7998x BT656-to-MIPI-CSI2 decoder > >> + > >> +The Intersil ISL7998x is a BT656-to-MIPI-CSI decoder which, capable of > >> +receiving up to four analog stream and multiplexing them into up to four > >> +MIPI CSI2 virtual channels, using one MIPI clock lane and 1/2 data lanes. > >> + > > > > The documentation is not public, so I can only read what's reported on > > the website and the short public datasheet at [1] > > Right > > > From my understanding of the product page, both the ISL79987 and > > ILS79988 devices support up to 4 analog inputs, and provide a CSI-2 > > output and a BT656 output respectively. > > > > What am I reading wrong ? > > ISL79987 is analog video to mipi csi2 ; I have this chip. > ISL79988 is analog video to bt656 ; I don't have this chip. > So please change the description to "Analog to MIPI CSI-2/BT565 decoder" > > [1] https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html > > > >> +Required Properties: > >> +- compatible: value should be "isil,isl79987" And here you might want to have 2 different compatibles for 79987 and 79988. > >> +- pd-gpios: a GPIO spec for the Power Down pin (active high) > >> + > >> +Option Properties: > >> +- isil,num-inputs: Number of connected inputs (1, 2 or 4) > > > > Can't you derive this from the number of connected input endpoints > > instead of providing a custom property? > > Input endpoints from where ? > See below :) > >> + > >> +For further reading on port node refer to > >> +Documentation/devicetree/bindings/media/video-interfaces.txt. > >> + > > > > I think a description of the supported ports and their intended > > usages is required here. You have up to 4 inputs and 1 output port, > > how do you expect them to be numbered? is port@4 the last input or the > > output one? > > The only port is the MIPI CSI2 , see the example below. > > >> +Example: > >> + > >> + i2c_master { > >> + isl7998x_mipi@44 { > >> + compatible = "isil,isl79987"; > >> + reg = <0x44>; > >> + isil,num-inputs = <4>; > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&pinctrl_videoadc>; > >> + pd-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; > >> + status = "okay"; > >> + > >> + port { > >> + isl79987_to_mipi_csi2: endpoint { > >> + remote-endpoint = <&mipi_csi2_in>; > >> + clock-lanes = <0>; > >> + data-lanes = <1 2>; > >> + }; > > > > I see from the example you only support one output port? How do you > > model the input ones. > > I don't . Do we model analog inputs now somehow ? I really think so, please see: Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt And as an example of a board device tree using connectors to model analog input see how the cvbs input on Salvator-X is described: cvbs-in { compatible = "composite-video-connector"; label = "CVBS IN"; port { cvbs_con: endpoint { remote-endpoint = <&adv7482_ain7>; }; }; }; I think you should provide 4 input ports, where to connect input from the analog connectors, and derive the number of enabled inputs from the number of endpoints connected to an active remote. Also, you might want to provide 2 output ports, one CSI-2 and one BT565 and parse the right one depending on the compatible string. I would also place the input ports last (from port@2 to port@5) so that we make easier to support similar chips with more inputs (if any). That said, I'm no expert of analog video, so others might have different opinions :) Thanks j > > -- > Best regards, > Marek Vasut [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-28 15:10 ` Jacopo Mondi @ 2019-05-28 17:49 ` Marek Vasut 2019-05-29 6:28 ` Jacopo Mondi 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2019-05-28 17:49 UTC (permalink / raw) To: Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree On 5/28/19 5:10 PM, Jacopo Mondi wrote: [...] >>> From my understanding of the product page, both the ISL79987 and >>> ILS79988 devices support up to 4 analog inputs, and provide a CSI-2 >>> output and a BT656 output respectively. >>> >>> What am I reading wrong ? >> >> ISL79987 is analog video to mipi csi2 ; I have this chip. >> ISL79988 is analog video to bt656 ; I don't have this chip. >> > > So please change the description to "Analog to MIPI CSI-2/BT565 > decoder" Done >>> [1] https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html >>> >>>> +Required Properties: >>>> +- compatible: value should be "isil,isl79987" > > And here you might want to have 2 different compatibles for 79987 and > 79988. The 79988 is not supported yet, do we want to have it in the binding doc? [...] >>> I see from the example you only support one output port? How do you >>> model the input ones. >> >> I don't . Do we model analog inputs now somehow ? > > I really think so, please see: > Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt > > And as an example of a board device tree using connectors to model > analog input see how the cvbs input on Salvator-X is described: > > cvbs-in { > compatible = "composite-video-connector"; > label = "CVBS IN"; > > port { > cvbs_con: endpoint { > remote-endpoint = <&adv7482_ain7>; > }; > }; > }; > > I think you should provide 4 input ports, where to connect input from > the analog connectors, and derive the number of enabled inputs from > the number of endpoints connected to an active remote. Deriving the number of active physical inputs from some existing binding makes sense. However unlike the adv7482, the isl79987 does not support remapping the physical inputs to ADCs in the chip. It does support some remapping of physical inputs to MIPI CSI2 channels, but that's probably not very useful. > Also, you might want to provide 2 output ports, one CSI-2 and one > BT565 and parse the right one depending on the compatible string. The chip only has one physical output port (either CSI2 or parallel) and DT should model the hardware, so I would expect there to be one output port per chip ? > I would also place the input ports last (from port@2 to port@5) so > that we make easier to support similar chips with more inputs (if > any). > > That said, I'm no expert of analog video, so others might have > different opinions :) > > Thanks > j > >> >> -- >> Best regards, >> Marek Vasut -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-28 17:49 ` Marek Vasut @ 2019-05-29 6:28 ` Jacopo Mondi 2019-05-29 10:41 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Jacopo Mondi @ 2019-05-29 6:28 UTC (permalink / raw) To: Marek Vasut Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree [-- Attachment #1: Type: text/plain, Size: 3600 bytes --] Hi Marek, On Tue, May 28, 2019 at 07:49:57PM +0200, Marek Vasut wrote: > On 5/28/19 5:10 PM, Jacopo Mondi wrote: > [...] > > >>> From my understanding of the product page, both the ISL79987 and > >>> ILS79988 devices support up to 4 analog inputs, and provide a CSI-2 > >>> output and a BT656 output respectively. > >>> > >>> What am I reading wrong ? > >> > >> ISL79987 is analog video to mipi csi2 ; I have this chip. > >> ISL79988 is analog video to bt656 ; I don't have this chip. > >> > > > > So please change the description to "Analog to MIPI CSI-2/BT565 > > decoder" > > Done > Great! > >>> [1] https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html > >>> > >>>> +Required Properties: > >>>> +- compatible: value should be "isil,isl79987" > > > > And here you might want to have 2 different compatibles for 79987 and > > 79988. > > The 79988 is not supported yet, do we want to have it in the binding doc? > I got mislead by the isl7998x naming scheme you used... I would say that's up to you, the two chips seems very similar, and it might make sense to provide bindings that support both. At the same time, as long as the here defined bindings does not prevent future expansions to include the ISL79988, its support could be safely post-poned. In that case please s/isl7998x/isl79987/ in this document and do not mention BT565 in the description. > [...] > > >>> I see from the example you only support one output port? How do you > >>> model the input ones. > >> > >> I don't . Do we model analog inputs now somehow ? > > > > I really think so, please see: > > Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt > > > > And as an example of a board device tree using connectors to model > > analog input see how the cvbs input on Salvator-X is described: > > > > cvbs-in { > > compatible = "composite-video-connector"; > > label = "CVBS IN"; > > > > port { > > cvbs_con: endpoint { > > remote-endpoint = <&adv7482_ain7>; > > }; > > }; > > }; > > > > I think you should provide 4 input ports, where to connect input from > > the analog connectors, and derive the number of enabled inputs from > > the number of endpoints connected to an active remote. > > Deriving the number of active physical inputs from some existing binding > makes sense. > > However unlike the adv7482, the isl79987 does not support remapping the > physical inputs to ADCs in the chip. It does support some remapping of > physical inputs to MIPI CSI2 channels, but that's probably not very useful. > I understand, but I will now use against you the argument you have correctly pointed out here below that DT should describe hardware, and the hardware has indeed 4 input ports.. > > Also, you might want to provide 2 output ports, one CSI-2 and one > > BT565 and parse the right one depending on the compatible string. > > The chip only has one physical output port (either CSI2 or parallel) and > DT should model the hardware, so I would expect there to be one output > port per chip ? You are right indeed, there should be one output port only, whose content will be different between the two chips... Sorry for the confusion. Thanks j > > > I would also place the input ports last (from port@2 to port@5) so > > that we make easier to support similar chips with more inputs (if > > any). > > > > That said, I'm no expert of analog video, so others might have > > different opinions :) > > > > Thanks > > j > > > >> > >> -- > >> Best regards, > >> Marek Vasut > > > -- > Best regards, > Marek Vasut [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-29 6:28 ` Jacopo Mondi @ 2019-05-29 10:41 ` Marek Vasut 2019-05-29 11:04 ` Ian Arkver 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2019-05-29 10:41 UTC (permalink / raw) To: Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree On 5/29/19 8:28 AM, Jacopo Mondi wrote: [...] >>>>> [1] https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html >>>>> >>>>>> +Required Properties: >>>>>> +- compatible: value should be "isil,isl79987" >>> >>> And here you might want to have 2 different compatibles for 79987 and >>> 79988. >> >> The 79988 is not supported yet, do we want to have it in the binding doc? >> > > I got mislead by the isl7998x naming scheme you used... > > I would say that's up to you, the two chips seems very similar, > and it might make sense to provide bindings that support both. At the > same time, as long as the here defined bindings does not prevent > future expansions to include the ISL79988, its support could be safely > post-poned. In that case please s/isl7998x/isl79987/ in this document > and do not mention BT565 in the description. Right >> [...] >> >>>>> I see from the example you only support one output port? How do you >>>>> model the input ones. >>>> >>>> I don't . Do we model analog inputs now somehow ? >>> >>> I really think so, please see: >>> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt >>> >>> And as an example of a board device tree using connectors to model >>> analog input see how the cvbs input on Salvator-X is described: >>> >>> cvbs-in { >>> compatible = "composite-video-connector"; >>> label = "CVBS IN"; >>> >>> port { >>> cvbs_con: endpoint { >>> remote-endpoint = <&adv7482_ain7>; >>> }; >>> }; >>> }; >>> >>> I think you should provide 4 input ports, where to connect input from >>> the analog connectors, and derive the number of enabled inputs from >>> the number of endpoints connected to an active remote. >> >> Deriving the number of active physical inputs from some existing binding >> makes sense. >> >> However unlike the adv7482, the isl79987 does not support remapping the >> physical inputs to ADCs in the chip. It does support some remapping of >> physical inputs to MIPI CSI2 channels, but that's probably not very useful. >> > > I understand, but I will now use against you the argument you have > correctly pointed out here below that DT should describe hardware, and > the hardware has indeed 4 input ports.. My question here is whether it makes sense to describe the ports even if they cannot be muxed to different ADC. Does it ? [...] -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-29 10:41 ` Marek Vasut @ 2019-05-29 11:04 ` Ian Arkver 2019-05-29 11:09 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Ian Arkver @ 2019-05-29 11:04 UTC (permalink / raw) To: Marek Vasut, Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree Hi, On 29/05/2019 11:41, Marek Vasut wrote: > On 5/29/19 8:28 AM, Jacopo Mondi wrote: > > [...] > >>>>>> [1] https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html >>>>>> >>>>>>> +Required Properties: >>>>>>> +- compatible: value should be "isil,isl79987" >>>> >>>> And here you might want to have 2 different compatibles for 79987 and >>>> 79988. >>> >>> The 79988 is not supported yet, do we want to have it in the binding doc? >>> >> >> I got mislead by the isl7998x naming scheme you used... >> >> I would say that's up to you, the two chips seems very similar, >> and it might make sense to provide bindings that support both. At the >> same time, as long as the here defined bindings does not prevent >> future expansions to include the ISL79988, its support could be safely >> post-poned. In that case please s/isl7998x/isl79987/ in this document >> and do not mention BT565 in the description. > > Right > >>> [...] >>> >>>>>> I see from the example you only support one output port? How do you >>>>>> model the input ones. >>>>> >>>>> I don't . Do we model analog inputs now somehow ? >>>> >>>> I really think so, please see: >>>> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt >>>> >>>> And as an example of a board device tree using connectors to model >>>> analog input see how the cvbs input on Salvator-X is described: >>>> >>>> cvbs-in { >>>> compatible = "composite-video-connector"; >>>> label = "CVBS IN"; >>>> >>>> port { >>>> cvbs_con: endpoint { >>>> remote-endpoint = <&adv7482_ain7>; >>>> }; >>>> }; >>>> }; >>>> >>>> I think you should provide 4 input ports, where to connect input from >>>> the analog connectors, and derive the number of enabled inputs from >>>> the number of endpoints connected to an active remote. >>> >>> Deriving the number of active physical inputs from some existing binding >>> makes sense. >>> >>> However unlike the adv7482, the isl79987 does not support remapping the >>> physical inputs to ADCs in the chip. It does support some remapping of >>> physical inputs to MIPI CSI2 channels, but that's probably not very useful. >>> >> >> I understand, but I will now use against you the argument you have >> correctly pointed out here below that DT should describe hardware, and >> the hardware has indeed 4 input ports.. > > My question here is whether it makes sense to describe the ports even if > they cannot be muxed to different ADC. Does it ? Each input port can be either differential CVBS or single ended with a 2:1 input select mux. It would be nice to be able to describe this. You cannot remap the inputs to different ADCs, but you can remap the ADCs to different VC IDs using the ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT register. Describing each input would proivde somewhere to specify the vc-id. Regards, Ian > > [...] > ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-29 11:04 ` Ian Arkver @ 2019-05-29 11:09 ` Marek Vasut 2019-05-29 11:15 ` Ian Arkver 2019-05-29 13:43 ` Jacopo Mondi 0 siblings, 2 replies; 22+ messages in thread From: Marek Vasut @ 2019-05-29 11:09 UTC (permalink / raw) To: Ian Arkver, Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree On 5/29/19 1:04 PM, Ian Arkver wrote: > Hi, > > On 29/05/2019 11:41, Marek Vasut wrote: >> On 5/29/19 8:28 AM, Jacopo Mondi wrote: >> >> [...] >> >>>>>>> [1] >>>>>>> https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html >>>>>>> >>>>>>> >>>>>>>> +Required Properties: >>>>>>>> +- compatible: value should be "isil,isl79987" >>>>> >>>>> And here you might want to have 2 different compatibles for 79987 and >>>>> 79988. >>>> >>>> The 79988 is not supported yet, do we want to have it in the binding >>>> doc? >>>> >>> >>> I got mislead by the isl7998x naming scheme you used... >>> >>> I would say that's up to you, the two chips seems very similar, >>> and it might make sense to provide bindings that support both. At the >>> same time, as long as the here defined bindings does not prevent >>> future expansions to include the ISL79988, its support could be safely >>> post-poned. In that case please s/isl7998x/isl79987/ in this document >>> and do not mention BT565 in the description. >> >> Right >> >>>> [...] >>>> >>>>>>> I see from the example you only support one output port? How do you >>>>>>> model the input ones. >>>>>> >>>>>> I don't . Do we model analog inputs now somehow ? >>>>> >>>>> I really think so, please see: >>>>> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt >>>>> >>>>> >>>>> And as an example of a board device tree using connectors to model >>>>> analog input see how the cvbs input on Salvator-X is described: >>>>> >>>>> cvbs-in { >>>>> compatible = "composite-video-connector"; >>>>> label = "CVBS IN"; >>>>> >>>>> port { >>>>> cvbs_con: endpoint { >>>>> remote-endpoint = <&adv7482_ain7>; >>>>> }; >>>>> }; >>>>> }; >>>>> >>>>> I think you should provide 4 input ports, where to connect input from >>>>> the analog connectors, and derive the number of enabled inputs from >>>>> the number of endpoints connected to an active remote. >>>> >>>> Deriving the number of active physical inputs from some existing >>>> binding >>>> makes sense. >>>> >>>> However unlike the adv7482, the isl79987 does not support remapping the >>>> physical inputs to ADCs in the chip. It does support some remapping of >>>> physical inputs to MIPI CSI2 channels, but that's probably not very >>>> useful. >>>> >>> >>> I understand, but I will now use against you the argument you have >>> correctly pointed out here below that DT should describe hardware, and >>> the hardware has indeed 4 input ports.. >> >> My question here is whether it makes sense to describe the ports even if >> they cannot be muxed to different ADC. Does it ? > > Each input port can be either differential CVBS or single ended with a > 2:1 input select mux. It would be nice to be able to describe this. Where do you see that ? > You cannot remap the inputs to different ADCs, but you can remap the > ADCs to different VC IDs using the > ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT register. Describing each input > would proivde somewhere to specify the vc-id. I think Jacopo mentioned above the input muxing and the MIPI CSI2 VC muxing are two separate things. But I have to wonder, do we have a way of muxing the VCs in the DT or via the media controller yet ? -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-29 11:09 ` Marek Vasut @ 2019-05-29 11:15 ` Ian Arkver 2019-08-06 13:35 ` Marek Vasut 2019-05-29 13:43 ` Jacopo Mondi 1 sibling, 1 reply; 22+ messages in thread From: Ian Arkver @ 2019-05-29 11:15 UTC (permalink / raw) To: Marek Vasut, Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree Hi Marek, On 29/05/2019 12:09, Marek Vasut wrote: > On 5/29/19 1:04 PM, Ian Arkver wrote: >> Hi, >> >> On 29/05/2019 11:41, Marek Vasut wrote: >>> On 5/29/19 8:28 AM, Jacopo Mondi wrote: >>> >>> [...] >>> >>>>>>>> [1] >>>>>>>> https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html >>>>>>>> >>>>>>>> >>>>>>>>> +Required Properties: >>>>>>>>> +- compatible: value should be "isil,isl79987" >>>>>> >>>>>> And here you might want to have 2 different compatibles for 79987 and >>>>>> 79988. >>>>> >>>>> The 79988 is not supported yet, do we want to have it in the binding >>>>> doc? >>>>> >>>> >>>> I got mislead by the isl7998x naming scheme you used... >>>> >>>> I would say that's up to you, the two chips seems very similar, >>>> and it might make sense to provide bindings that support both. At the >>>> same time, as long as the here defined bindings does not prevent >>>> future expansions to include the ISL79988, its support could be safely >>>> post-poned. In that case please s/isl7998x/isl79987/ in this document >>>> and do not mention BT565 in the description. >>> >>> Right >>> >>>>> [...] >>>>> >>>>>>>> I see from the example you only support one output port? How do you >>>>>>>> model the input ones. >>>>>>> >>>>>>> I don't . Do we model analog inputs now somehow ? >>>>>> >>>>>> I really think so, please see: >>>>>> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt >>>>>> >>>>>> >>>>>> And as an example of a board device tree using connectors to model >>>>>> analog input see how the cvbs input on Salvator-X is described: >>>>>> >>>>>> cvbs-in { >>>>>> compatible = "composite-video-connector"; >>>>>> label = "CVBS IN"; >>>>>> >>>>>> port { >>>>>> cvbs_con: endpoint { >>>>>> remote-endpoint = <&adv7482_ain7>; >>>>>> }; >>>>>> }; >>>>>> }; >>>>>> >>>>>> I think you should provide 4 input ports, where to connect input from >>>>>> the analog connectors, and derive the number of enabled inputs from >>>>>> the number of endpoints connected to an active remote. >>>>> >>>>> Deriving the number of active physical inputs from some existing >>>>> binding >>>>> makes sense. >>>>> >>>>> However unlike the adv7482, the isl79987 does not support remapping the >>>>> physical inputs to ADCs in the chip. It does support some remapping of >>>>> physical inputs to MIPI CSI2 channels, but that's probably not very >>>>> useful. >>>>> >>>> >>>> I understand, but I will now use against you the argument you have >>>> correctly pointed out here below that DT should describe hardware, and >>>> the hardware has indeed 4 input ports.. >>> >>> My question here is whether it makes sense to describe the ports even if >>> they cannot be muxed to different ADC. Does it ? >> >> Each input port can be either differential CVBS or single ended with a >> 2:1 input select mux. It would be nice to be able to describe this. > > Where do you see that ? Bits 0 and 1 of each channel page's Differential Clamping Control 4 (0x39, ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_4). I don't think you change it from the default (single ended on the first input). Regards, Ian > >> You cannot remap the inputs to different ADCs, but you can remap the >> ADCs to different VC IDs using the >> ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT register. Describing each input >> would proivde somewhere to specify the vc-id. > > I think Jacopo mentioned above the input muxing and the MIPI CSI2 VC > muxing are two separate things. But I have to wonder, do we have a way > of muxing the VCs in the DT or via the media controller yet ? > ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-29 11:15 ` Ian Arkver @ 2019-08-06 13:35 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2019-08-06 13:35 UTC (permalink / raw) To: Ian Arkver, Jacopo Mondi Cc: linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree On 5/29/19 1:15 PM, Ian Arkver wrote: > Hi Marek, > > On 29/05/2019 12:09, Marek Vasut wrote: >> On 5/29/19 1:04 PM, Ian Arkver wrote: >>> Hi, >>> >>> On 29/05/2019 11:41, Marek Vasut wrote: >>>> On 5/29/19 8:28 AM, Jacopo Mondi wrote: >>>> >>>> [...] >>>> >>>>>>>>> [1] >>>>>>>>> https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>>>>>>> +Required Properties: >>>>>>>>>> +- compatible: value should be "isil,isl79987" >>>>>>> >>>>>>> And here you might want to have 2 different compatibles for 79987 >>>>>>> and >>>>>>> 79988. >>>>>> >>>>>> The 79988 is not supported yet, do we want to have it in the binding >>>>>> doc? >>>>>> >>>>> >>>>> I got mislead by the isl7998x naming scheme you used... >>>>> >>>>> I would say that's up to you, the two chips seems very similar, >>>>> and it might make sense to provide bindings that support both. At the >>>>> same time, as long as the here defined bindings does not prevent >>>>> future expansions to include the ISL79988, its support could be safely >>>>> post-poned. In that case please s/isl7998x/isl79987/ in this document >>>>> and do not mention BT565 in the description. >>>> >>>> Right >>>> >>>>>> [...] >>>>>> >>>>>>>>> I see from the example you only support one output port? How do >>>>>>>>> you >>>>>>>>> model the input ones. >>>>>>>> >>>>>>>> I don't . Do we model analog inputs now somehow ? >>>>>>> >>>>>>> I really think so, please see: >>>>>>> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt >>>>>>> >>>>>>> >>>>>>> >>>>>>> And as an example of a board device tree using connectors to model >>>>>>> analog input see how the cvbs input on Salvator-X is described: >>>>>>> >>>>>>> cvbs-in { >>>>>>> compatible = "composite-video-connector"; >>>>>>> label = "CVBS IN"; >>>>>>> >>>>>>> port { >>>>>>> cvbs_con: endpoint { >>>>>>> remote-endpoint = <&adv7482_ain7>; >>>>>>> }; >>>>>>> }; >>>>>>> }; >>>>>>> >>>>>>> I think you should provide 4 input ports, where to connect input >>>>>>> from >>>>>>> the analog connectors, and derive the number of enabled inputs from >>>>>>> the number of endpoints connected to an active remote. >>>>>> >>>>>> Deriving the number of active physical inputs from some existing >>>>>> binding >>>>>> makes sense. >>>>>> >>>>>> However unlike the adv7482, the isl79987 does not support >>>>>> remapping the >>>>>> physical inputs to ADCs in the chip. It does support some >>>>>> remapping of >>>>>> physical inputs to MIPI CSI2 channels, but that's probably not very >>>>>> useful. >>>>>> >>>>> >>>>> I understand, but I will now use against you the argument you have >>>>> correctly pointed out here below that DT should describe hardware, and >>>>> the hardware has indeed 4 input ports.. >>>> >>>> My question here is whether it makes sense to describe the ports >>>> even if >>>> they cannot be muxed to different ADC. Does it ? >>> >>> Each input port can be either differential CVBS or single ended with a >>> 2:1 input select mux. It would be nice to be able to describe this. >> >> Where do you see that ? > > Bits 0 and 1 of each channel page's Differential Clamping Control 4 > (0x39, ISL7998x_REG_Px_DEC_DIFF_CLMP_CTL_4). > > I don't think you change it from the default (single ended on the first > input). I don't, since I have no way to test the differential mode of operation. [...] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-29 11:09 ` Marek Vasut 2019-05-29 11:15 ` Ian Arkver @ 2019-05-29 13:43 ` Jacopo Mondi 2019-08-06 13:35 ` Marek Vasut 1 sibling, 1 reply; 22+ messages in thread From: Jacopo Mondi @ 2019-05-29 13:43 UTC (permalink / raw) To: Marek Vasut Cc: Ian Arkver, linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree [-- Attachment #1: Type: text/plain, Size: 6223 bytes --] HI Marek, On Wed, May 29, 2019 at 01:09:47PM +0200, Marek Vasut wrote: > On 5/29/19 1:04 PM, Ian Arkver wrote: > > Hi, > > > > On 29/05/2019 11:41, Marek Vasut wrote: > >> On 5/29/19 8:28 AM, Jacopo Mondi wrote: > >> > >> [...] > >> > >>>>>>> [1] > >>>>>>> https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html > >>>>>>> > >>>>>>> > >>>>>>>> +Required Properties: > >>>>>>>> +- compatible: value should be "isil,isl79987" > >>>>> > >>>>> And here you might want to have 2 different compatibles for 79987 and > >>>>> 79988. > >>>> > >>>> The 79988 is not supported yet, do we want to have it in the binding > >>>> doc? > >>>> > >>> > >>> I got mislead by the isl7998x naming scheme you used... > >>> > >>> I would say that's up to you, the two chips seems very similar, > >>> and it might make sense to provide bindings that support both. At the > >>> same time, as long as the here defined bindings does not prevent > >>> future expansions to include the ISL79988, its support could be safely > >>> post-poned. In that case please s/isl7998x/isl79987/ in this document > >>> and do not mention BT565 in the description. > >> > >> Right > >> > >>>> [...] > >>>> > >>>>>>> I see from the example you only support one output port? How do you > >>>>>>> model the input ones. > >>>>>> > >>>>>> I don't . Do we model analog inputs now somehow ? > >>>>> > >>>>> I really think so, please see: > >>>>> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt > >>>>> > >>>>> > >>>>> And as an example of a board device tree using connectors to model > >>>>> analog input see how the cvbs input on Salvator-X is described: > >>>>> > >>>>> cvbs-in { > >>>>> compatible = "composite-video-connector"; > >>>>> label = "CVBS IN"; > >>>>> > >>>>> port { > >>>>> cvbs_con: endpoint { > >>>>> remote-endpoint = <&adv7482_ain7>; > >>>>> }; > >>>>> }; > >>>>> }; > >>>>> > >>>>> I think you should provide 4 input ports, where to connect input from > >>>>> the analog connectors, and derive the number of enabled inputs from > >>>>> the number of endpoints connected to an active remote. > >>>> > >>>> Deriving the number of active physical inputs from some existing > >>>> binding > >>>> makes sense. > >>>> > >>>> However unlike the adv7482, the isl79987 does not support remapping the > >>>> physical inputs to ADCs in the chip. It does support some remapping of > >>>> physical inputs to MIPI CSI2 channels, but that's probably not very > >>>> useful. > >>>> > >>> > >>> I understand, but I will now use against you the argument you have > >>> correctly pointed out here below that DT should describe hardware, and > >>> the hardware has indeed 4 input ports.. > >> > >> My question here is whether it makes sense to describe the ports even if > >> they cannot be muxed to different ADC. Does it ? > > > > Each input port can be either differential CVBS or single ended with a > > 2:1 input select mux. It would be nice to be able to describe this. > > Where do you see that ? > > > You cannot remap the inputs to different ADCs, but you can remap the > > ADCs to different VC IDs using the > > ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT register. Describing each input > > would proivde somewhere to specify the vc-id. > > I think Jacopo mentioned above the input muxing and the MIPI CSI2 VC > muxing are two separate things. But I have to wonder, do we have a way > of muxing the VCs in the DT or via the media controller yet ? I'm not sure I get what you mean with "input muxing", do you mean controlling which input is directed to which ADC ? I don't have the chip manual, but according to what you and Ian said this is not possible. Selecting which input video stream is directed to which CSI-2 virtual channel in the output CSI-2 stream is not possible in mainline. There are patches in development that would allow you to do so, but their design is not fully finalized yet. They would, in any case, require you to have one sink pad for each input port, and while you could register as many pads as it is specified in your custom property, you would loose the notion of which input is connected to which port ie. when a single input (isil,num-inputs=1) is connected to an input port which is not the first one (anyway, quickly looking at 2/2 it seems to me you only register a single source pad for this device). The DT bindings layout is an orthogonal problem though. My opinion is that as the chip has 4 available input connections it should have 4 input ports in the bindings definition, and for each one you would register a sink pad. Only the actually connected ones should be present in the DTS, so that the driver knows which input port is active and, once something that allows you to control VC will land in mainline, it will let you tell something like "I want the video stream received on the input port@2 sent in virtual channel x in the output CSI-2 stream", but again this is quite an orthogonal issue. Sure thing is that with the current design and implementation, which afaict does not provides any sink pad, this is frowned upon (but you can then say 'who cares, since it's not here yet' :) Or what Ian said, if you can model a connector that provides 2 single ended inputs, each connected to an input port and muxed internally by the chip, you could only do that if you have numbered input ports I guess. Nobody requires you support any of these, but at least bindings should be defined in a future proof way, to avoid later changes to the ABI. Anyway, you had my opinion, multiple times already, and as I'm not in any position to judge if something is acceptable for merge or not, I'll now get quiet hoping that this prolonged email exchange drags in opinion from more experienced people to tell you which direction you should take and if what you have here is fine already or not :) Cheers j > > -- > Best regards, > Marek Vasut [-- Attachment #2: signature.asc --] [-- Type: application/pgp-signature, Size: 833 bytes --] ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-29 13:43 ` Jacopo Mondi @ 2019-08-06 13:35 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2019-08-06 13:35 UTC (permalink / raw) To: Jacopo Mondi Cc: Ian Arkver, linux-media, Sakari Ailus, Mauro Carvalho Chehab, Rob Herring, devicetree On 5/29/19 3:43 PM, Jacopo Mondi wrote: > HI Marek, Hi, > On Wed, May 29, 2019 at 01:09:47PM +0200, Marek Vasut wrote: >> On 5/29/19 1:04 PM, Ian Arkver wrote: >>> Hi, >>> >>> On 29/05/2019 11:41, Marek Vasut wrote: >>>> On 5/29/19 8:28 AM, Jacopo Mondi wrote: >>>> >>>> [...] >>>> >>>>>>>>> [1] >>>>>>>>> https://www.renesas.com/eu/en/products/audio-video/video-decoders-encoders/video-decoders/device/ISL79987.html >>>>>>>>> >>>>>>>>> >>>>>>>>>> +Required Properties: >>>>>>>>>> +- compatible: value should be "isil,isl79987" >>>>>>> >>>>>>> And here you might want to have 2 different compatibles for 79987 and >>>>>>> 79988. >>>>>> >>>>>> The 79988 is not supported yet, do we want to have it in the binding >>>>>> doc? >>>>>> >>>>> >>>>> I got mislead by the isl7998x naming scheme you used... >>>>> >>>>> I would say that's up to you, the two chips seems very similar, >>>>> and it might make sense to provide bindings that support both. At the >>>>> same time, as long as the here defined bindings does not prevent >>>>> future expansions to include the ISL79988, its support could be safely >>>>> post-poned. In that case please s/isl7998x/isl79987/ in this document >>>>> and do not mention BT565 in the description. >>>> >>>> Right >>>> >>>>>> [...] >>>>>> >>>>>>>>> I see from the example you only support one output port? How do you >>>>>>>>> model the input ones. >>>>>>>> >>>>>>>> I don't . Do we model analog inputs now somehow ? >>>>>>> >>>>>>> I really think so, please see: >>>>>>> Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt >>>>>>> >>>>>>> >>>>>>> And as an example of a board device tree using connectors to model >>>>>>> analog input see how the cvbs input on Salvator-X is described: >>>>>>> >>>>>>> cvbs-in { >>>>>>> compatible = "composite-video-connector"; >>>>>>> label = "CVBS IN"; >>>>>>> >>>>>>> port { >>>>>>> cvbs_con: endpoint { >>>>>>> remote-endpoint = <&adv7482_ain7>; >>>>>>> }; >>>>>>> }; >>>>>>> }; >>>>>>> >>>>>>> I think you should provide 4 input ports, where to connect input from >>>>>>> the analog connectors, and derive the number of enabled inputs from >>>>>>> the number of endpoints connected to an active remote. >>>>>> >>>>>> Deriving the number of active physical inputs from some existing >>>>>> binding >>>>>> makes sense. >>>>>> >>>>>> However unlike the adv7482, the isl79987 does not support remapping the >>>>>> physical inputs to ADCs in the chip. It does support some remapping of >>>>>> physical inputs to MIPI CSI2 channels, but that's probably not very >>>>>> useful. >>>>>> >>>>> >>>>> I understand, but I will now use against you the argument you have >>>>> correctly pointed out here below that DT should describe hardware, and >>>>> the hardware has indeed 4 input ports.. >>>> >>>> My question here is whether it makes sense to describe the ports even if >>>> they cannot be muxed to different ADC. Does it ? >>> >>> Each input port can be either differential CVBS or single ended with a >>> 2:1 input select mux. It would be nice to be able to describe this. >> >> Where do you see that ? >> >>> You cannot remap the inputs to different ADCs, but you can remap the >>> ADCs to different VC IDs using the >>> ISL7998x_REG_P5_LI_ENGINE_VC_ASSIGNMENT register. Describing each input >>> would proivde somewhere to specify the vc-id. >> >> I think Jacopo mentioned above the input muxing and the MIPI CSI2 VC >> muxing are two separate things. But I have to wonder, do we have a way >> of muxing the VCs in the DT or via the media controller yet ? > > I'm not sure I get what you mean with "input muxing", do you mean > controlling which input is directed to which ADC ? Yes > I don't have the > chip manual, but according to what you and Ian said this is not > possible. Correct. You can only remap ADC output(s) to different MIPI CSI2 VC(s). > Selecting which input video stream is directed to which CSI-2 virtual > channel in the output CSI-2 stream is not possible in mainline. There > are patches in development that would allow you to do so, but their > design is not fully finalized yet. They would, in any case, require > you to have one sink pad for each input port Right, and the iMX6 CSI2 driver which I use for development doesn't support that yet either. >, and while you could > register as many pads as it is specified in your custom property, > you would loose the notion of which input is connected to which port > ie. when a single input (isil,num-inputs=1) is connected to an input > port which is not the first one (anyway, quickly looking at 2/2 it > seems to me you only register a single source pad for this device). > > The DT bindings layout is an orthogonal problem though. My opinion is > that as the chip has 4 available input connections it should have 4 > input ports in the bindings definition, and for each one you would > register a sink pad. Who would be the source for such an input "sink" pad though ? I looked at Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt, as you suggested above, but this is for video _OUTPUT_ devices, not input devices, so that's likely not what I want. > Only the actually connected ones should be present > in the DTS, so that the driver knows which input port is active and, > once something that allows you to control VC will land in mainline, > it will let you tell something like "I want the video stream > received on the input port@2 sent in virtual channel x in the output > CSI-2 stream", but again this is quite an orthogonal issue. Sure thing > is that with the current design and implementation, which afaict does > not provides any sink pad, this is frowned upon (but you can then say > 'who cares, since it's not here yet' :) Fine, so let's ignore this for now. > Or what Ian said, if you can model a connector that provides 2 single > ended inputs, each connected to an input port and muxed internally by > the chip, you could only do that if you have numbered input ports I > guess. Nobody requires you support any of these, but at least bindings > should be defined in a future proof way, to avoid later changes to the > ABI. Well, if endpoint 0 is the MIPI CSI2 output, then you can always add more endpoints (1..4) for the analog inputs . In this way , the bindings are already future-proof. Or shall the input ports come first (as endpoints 0..3) and be followed by the MIPI CSI2 output (4) ? If so, that would make counting the (varying number of) inputs a bit cumbersome in the driver. > Anyway, you had my opinion, multiple times already, and as I'm not in > any position to judge if something is acceptable for merge or not, > I'll now get quiet hoping that this prolonged email exchange drags in > opinion from more experienced people to tell you which direction you > should take and if what you have here is fine already or not :) > > Cheers > j > >> >> -- >> Best regards, >> Marek Vasut -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-05-20 20:18 [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Marek Vasut 2019-05-20 20:18 ` [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x Marek Vasut 2019-05-28 11:47 ` [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Jacopo Mondi @ 2019-07-01 8:04 ` Sakari Ailus 2019-08-06 13:35 ` Marek Vasut 2 siblings, 1 reply; 22+ messages in thread From: Sakari Ailus @ 2019-07-01 8:04 UTC (permalink / raw) To: Marek Vasut; +Cc: linux-media, Mauro Carvalho Chehab, Rob Herring, devicetree Hi Marek, On Mon, May 20, 2019 at 10:18:11PM +0200, Marek Vasut wrote: > Add bindings for the Intersil ISL7998x BT656-to-MIPI-CSI2 decoder. > > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Sakari Ailus <sakari.ailus@linux.intel.com> > Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: devicetree@vger.kernel.org > To: linux-media@vger.kernel.org > --- > .../bindings/media/i2c/isl7998x.txt | 37 +++++++++++++++++++ > 1 file changed, 37 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/isl7998x.txt > > diff --git a/Documentation/devicetree/bindings/media/i2c/isl7998x.txt b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt > new file mode 100644 > index 000000000000..c21703983360 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt > @@ -0,0 +1,37 @@ > +Intersil ISL7998x BT656-to-MIPI-CSI2 decoder > + > +The Intersil ISL7998x is a BT656-to-MIPI-CSI decoder which, capable of > +receiving up to four analog stream and multiplexing them into up to four > +MIPI CSI2 virtual channels, using one MIPI clock lane and 1/2 data lanes. > + > +Required Properties: > +- compatible: value should be "isil,isl79987" > +- pd-gpios: a GPIO spec for the Power Down pin (active high) > + > +Option Properties: > +- isil,num-inputs: Number of connected inputs (1, 2 or 4) The presence of ports describing connected Bt.656 inputs tells this. > + > +For further reading on port node refer to > +Documentation/devicetree/bindings/media/video-interfaces.txt. Which endpoint properties are relevant for the endpoint(s) in the CSI-2 port? How about the ports describing the Bt.656 interfaces? You should have those, too... > + > +Example: > + > + i2c_master { > + isl7998x_mipi@44 { > + compatible = "isil,isl79987"; > + reg = <0x44>; > + isil,num-inputs = <4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_videoadc>; > + pd-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + > + port { > + isl79987_to_mipi_csi2: endpoint { > + remote-endpoint = <&mipi_csi2_in>; > + clock-lanes = <0>; > + data-lanes = <1 2>; > + }; > + }; > + }; > + }; > -- Regards, Sakari Ailus sakari.ailus@linux.intel.com ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings 2019-07-01 8:04 ` Sakari Ailus @ 2019-08-06 13:35 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2019-08-06 13:35 UTC (permalink / raw) To: Sakari Ailus; +Cc: linux-media, Mauro Carvalho Chehab, Rob Herring, devicetree On 7/1/19 10:04 AM, Sakari Ailus wrote: > Hi Marek, > > On Mon, May 20, 2019 at 10:18:11PM +0200, Marek Vasut wrote: >> Add bindings for the Intersil ISL7998x BT656-to-MIPI-CSI2 decoder. >> >> Signed-off-by: Marek Vasut <marex@denx.de> >> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> >> Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> >> Cc: Rob Herring <robh+dt@kernel.org> >> Cc: devicetree@vger.kernel.org >> To: linux-media@vger.kernel.org >> --- >> .../bindings/media/i2c/isl7998x.txt | 37 +++++++++++++++++++ >> 1 file changed, 37 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/media/i2c/isl7998x.txt >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/isl7998x.txt b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt >> new file mode 100644 >> index 000000000000..c21703983360 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/i2c/isl7998x.txt >> @@ -0,0 +1,37 @@ >> +Intersil ISL7998x BT656-to-MIPI-CSI2 decoder >> + >> +The Intersil ISL7998x is a BT656-to-MIPI-CSI decoder which, capable of >> +receiving up to four analog stream and multiplexing them into up to four >> +MIPI CSI2 virtual channels, using one MIPI clock lane and 1/2 data lanes. >> + >> +Required Properties: >> +- compatible: value should be "isil,isl79987" >> +- pd-gpios: a GPIO spec for the Power Down pin (active high) >> + >> +Option Properties: >> +- isil,num-inputs: Number of connected inputs (1, 2 or 4) > > The presence of ports describing connected Bt.656 inputs tells this. > >> + >> +For further reading on port node refer to >> +Documentation/devicetree/bindings/media/video-interfaces.txt. > > Which endpoint properties are relevant for the endpoint(s) in the CSI-2 port? clock-lanes, data-lanes and the remote-endpoint . > How about the ports describing the Bt.656 interfaces? You should have > those, too... So who would be connected to these analog "input" endpoint ? What would be their "remote-endpoint" ? >> + >> +Example: >> + >> + i2c_master { >> + isl7998x_mipi@44 { >> + compatible = "isil,isl79987"; >> + reg = <0x44>; >> + isil,num-inputs = <4>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_videoadc>; >> + pd-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; >> + status = "okay"; >> + >> + port { >> + isl79987_to_mipi_csi2: endpoint { >> + remote-endpoint = <&mipi_csi2_in>; >> + clock-lanes = <0>; >> + data-lanes = <1 2>; >> + }; >> + }; >> + }; >> + }; >> > -- Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
end of thread, other threads:[~2019-08-12 15:38 UTC | newest] Thread overview: 22+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-05-20 20:18 [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Marek Vasut 2019-05-20 20:18 ` [PATCH 2/2] media: i2c: isl7998x: Add driver for Intersil ISL7998x Marek Vasut 2019-07-01 7:58 ` Jacopo Mondi 2019-08-06 14:03 ` Marek Vasut 2019-08-12 15:39 ` Jacopo Mondi 2019-07-01 8:43 ` Sakari Ailus 2019-08-06 14:25 ` Marek Vasut 2019-07-01 8:46 ` Sakari Ailus 2019-05-28 11:47 ` [PATCH 1/2] media: dt-bindings: Add Intersil ISL7998x DT bindings Jacopo Mondi 2019-05-28 14:36 ` Marek Vasut 2019-05-28 15:10 ` Jacopo Mondi 2019-05-28 17:49 ` Marek Vasut 2019-05-29 6:28 ` Jacopo Mondi 2019-05-29 10:41 ` Marek Vasut 2019-05-29 11:04 ` Ian Arkver 2019-05-29 11:09 ` Marek Vasut 2019-05-29 11:15 ` Ian Arkver 2019-08-06 13:35 ` Marek Vasut 2019-05-29 13:43 ` Jacopo Mondi 2019-08-06 13:35 ` Marek Vasut 2019-07-01 8:04 ` Sakari Ailus 2019-08-06 13:35 ` Marek Vasut
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).