From: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
To: linux-media@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Cc: "Mauro Carvalho Chehab" <mchehab@kernel.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Maxime Ripard" <mripard@kernel.org>,
"Chen-Yu Tsai" <wens@csie.org>,
"Jernej Skrabec" <jernej.skrabec@siol.net>,
"Paul Kocialkowski" <paul.kocialkowski@bootlin.com>,
"Hans Verkuil" <hverkuil@xs4all.nl>,
"Sakari Ailus" <sakari.ailus@linux.intel.com>,
"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>,
kevin.lhopital@hotmail.com,
"Kévin L'hôpital" <kevin.lhopital@bootlin.com>
Subject: [PATCH NOT FOR MERGE v4 3/3] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865
Date: Fri, 11 Dec 2020 16:44:28 +0100 [thread overview]
Message-ID: <20201211154428.153762-4-paul.kocialkowski@bootlin.com> (raw)
In-Reply-To: <20201211154428.153762-1-paul.kocialkowski@bootlin.com>
From: Kévin L'hôpital <kevin.lhopital@bootlin.com>
The Bananapi M3 supports a camera module which includes an OV8865 sensor
connected via the parallel CSI interface and an OV8865 sensor connected
via MIPI CSI-2.
The I2C2 bus is shared by the two sensors as well as the (active-low)
reset signal, but each sensor has it own shutdown line.
Signed-off-by: Kévin L'hôpital <kevin.lhopital@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
---
arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 102 +++++++++++++++++++
1 file changed, 102 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
index 431f70234d36..b437eaeb91e9 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
@@ -85,6 +85,30 @@ green {
};
};
+ reg_ov8865_avdd: ov8865-avdd {
+ compatible = "regulator-fixed";
+ regulator-name = "ov8865-avdd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <®_dldo4>;
+ };
+
+ reg_ov8865_dovdd: ov8865-dovdd {
+ compatible = "regulator-fixed";
+ regulator-name = "ov8865-dovdd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <®_dldo4>;
+ };
+
+ reg_ov8865_dvdd: ov8865-dvdd {
+ compatible = "regulator-fixed";
+ regulator-name = "ov8865-dvdd";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <®_eldo1>;
+ };
+
reg_usb1_vbus: reg-usb1-vbus {
compatible = "regulator-fixed";
regulator-name = "usb1-vbus";
@@ -115,6 +139,23 @@ &cpu100 {
cpu-supply = <®_dcdc3>;
};
+&csi {
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ csi_in_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_out_csi>;
+ }
+ };
+ };
+};
+
&de {
status = "okay";
};
@@ -147,6 +188,36 @@ hdmi_out_con: endpoint {
};
};
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pe_pins>;
+ status = "okay";
+
+ ov8865: camera@36 {
+ compatible = "ovti,ov8865";
+ reg = <0x36>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&csi_mclk_pin>;
+ clocks = <&ccu CLK_CSI_MCLK>;
+ assigned-clocks = <&ccu CLK_CSI_MCLK>;
+ assigned-clock-rates = <24000000>;
+ avdd-supply = <®_ov8865_avdd>;
+ dovdd-supply = <®_ov8865_dovdd>;
+ dvdd-supply = <®_ov8865_dvdd>;
+ powerdown-gpios = <&pio 4 17 GPIO_ACTIVE_LOW>; /* PE17 */
+ reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
+
+ port {
+ ov8865_out_mipi_csi2: endpoint {
+ data-lanes = <1 2 3 4>;
+ link-frequencies = /bits/ 64 <360000000>;
+
+ remote-endpoint = <&mipi_csi2_in_ov8865>;
+ };
+ };
+ };
+};
+
&mdio {
rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
@@ -154,6 +225,24 @@ rgmii_phy: ethernet-phy@1 {
};
};
+&mipi_csi2 {
+ status = "okay";
+};
+
+&mipi_csi2_in {
+ mipi_csi2_in_ov8865: endpoint {
+ data-lanes = <1 2 3 4>;
+
+ remote-endpoint = <&ov8865_out_mipi_csi2>;
+ };
+};
+
+&mipi_csi2_out {
+ mipi_csi2_out_csi: endpoint {
+ remote-endpoint = <&csi_in_mipi_csi2>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
@@ -327,11 +416,24 @@ ®_dldo3 {
regulator-name = "vcc-pd";
};
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-csi";
+};
+
®_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "dvdd-csi-r";
+};
+
®_fldo1 {
regulator-min-microvolt = <1080000>;
regulator-max-microvolt = <1320000>;
--
2.29.2
next prev parent reply other threads:[~2020-12-11 16:42 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-11 15:44 [PATCH v4 0/3] media: i2c: OV8865 image sensor support Paul Kocialkowski
2020-12-11 15:44 ` [PATCH v4 1/3] dt-bindings: media: i2c: Add OV8865 bindings documentation Paul Kocialkowski
2020-12-11 15:44 ` [PATCH v4 2/3] media: i2c: Add support for the OV8865 image sensor Paul Kocialkowski
2020-12-11 15:44 ` Paul Kocialkowski [this message]
2020-12-31 14:26 [PATCH v4 0/3] media: i2c: OV8865 image sensor support Paul Kocialkowski
2020-12-31 14:27 ` [PATCH NOT FOR MERGE v4 3/3] ARM: dts: sun8i: a83t: bananapi-m3: Enable MIPI CSI-2 with OV8865 Paul Kocialkowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201211154428.153762-4-paul.kocialkowski@bootlin.com \
--to=paul.kocialkowski@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=hverkuil@xs4all.nl \
--cc=jernej.skrabec@siol.net \
--cc=kevin.lhopital@bootlin.com \
--cc=kevin.lhopital@hotmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=mripard@kernel.org \
--cc=robh+dt@kernel.org \
--cc=sakari.ailus@linux.intel.com \
--cc=thomas.petazzoni@bootlin.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).