Hi Hans,

On Wed, Dec 16, 2020 at 01:35:43PM +0100, Hans Verkuil wrote:
> Hi Maxime,
> 
> On 10/12/2020 14:46, Maxime Ripard wrote:
> > Hi,
> > 
> > Here's a series introducing the CEC support for the BCM2711 found on the
> > RaspberryPi4.
> > 
> > The BCM2711 HDMI controller uses a similar layout for the CEC registers, the
> > main difference being that the interrupt handling part is now shared between
> > both HDMI controllers.
> > 
> > This series is mainly about fixing a couple of bugs, reworking the driver to
> > support having two different interrupts, one for each direction, provided by an
> > external irqchip, and enables the irqchip driver for the controller we have.
> > 
> > This has been tested on an RPi3 and RPi4, but requires the latest firmware.
> > It's is based on the 10 and 12 bpc series.
> 
> This series looks good to me. Before I give my Acked-by for this series, can you
> confirm that it is possible to transmit the Image View On message on both outputs
> of the RPi4 when the HPD is low?
> 
> See section "CEC Without HPD" in https://hverkuil.home.xs4all.nl/cec-status.txt
> on how to test this with a Pulse-Eight device.
> 
> This should work.

This is the output on the RPi4:

# cec-ctl --playback
Driver Info:
	Driver Name                : vc4_hdmi
	Adapter Name               : vc4
	Capabilities               : 0x0000010e
		Logical Addresses
		Transmit
		Passthrough
	Driver version             : 5.10.0
	Available Logical Addresses: 1
	Physical Address           : f.f.f.f
	Logical Address Mask       : 0x0000
	CEC Version                : 2.0
	Vendor ID                  : 0x000c03 (HDMI)
	OSD Name                   : Playback
	Logical Addresses          : 1 (Allow RC Passthrough)

	  Logical Address          : Not Allocated
	    Primary Device Type    : Playback
	    Logical Address Type   : Playback
	    All Device Types       : Playback
	    RC TV Profile          : None
	    Device Features        :
		None

# cec-ctl -t0 --image-view-on
Driver Info:
	Driver Name                : vc4_hdmi
	Adapter Name               : vc4
	Capabilities               : 0x0000010e
		Logical Addresses
		Transmit
		Passthrough
	Driver version             : 5.10.0
	Available Logical Addresses: 1
	Physical Address           : f.f.f.f
	Logical Address Mask       : 0x0000
	CEC Version                : 2.0
	Vendor ID                  : 0x000c03 (HDMI)
	OSD Name                   : Playback
	Logical Addresses          : 1 (Allow RC Passthrough)

	  Logical Address          : Not Allocated
	    Primary Device Type    : Playback
	    Logical Address Type   : Playback
	    All Device Types       : Playback
	    RC TV Profile          : None
	    Device Features        :
		None


Transmit from Unregistered to TV (15 to 0):
CEC_MSG_IMAGE_VIEW_ON (0x04)
	Sequence: 1 Tx Timestamp: 77.631s


And this is the output on my desktop with the Pulse-Eight:
$ sudo cec-ctl -p0.0.0.0 --tv
Driver Info:
	Driver Name                : pulse8-cec
	Adapter Name               : serio0
	Capabilities               : 0x0000003f
		Physical Address
		Logical Addresses
		Transmit
		Passthrough
		Remote Control Support
		Monitor All
	Driver version             : 5.9.8
	Available Logical Addresses: 1
	Connector Info             : None
	Physical Address           : 0.0.0.0
	Logical Address Mask       : 0x0001
	CEC Version                : 2.0
	Vendor ID                  : 0x000c03 (HDMI)
	OSD Name                   : 'TV  '
	Logical Addresses          : 1 (Allow RC Passthrough)

	  Logical Address          : 0 (TV)
	    Primary Device Type    : TV
	    Logical Address Type   : TV
	    All Device Types       : TV
	    RC TV Profile          : None
	    Device Features        :
		None

$ sudo cec-ctl -M
Driver Info:
	Driver Name                : pulse8-cec
	Adapter Name               : serio0
	Capabilities               : 0x0000003f
		Physical Address
		Logical Addresses
		Transmit
		Passthrough
		Remote Control Support
		Monitor All
	Driver version             : 5.9.8
	Available Logical Addresses: 1
	Connector Info             : None
	Physical Address           : 0.0.0.0
	Logical Address Mask       : 0x0001
	CEC Version                : 2.0
	Vendor ID                  : 0x000c03 (HDMI)
	OSD Name                   : 'TV  '
	Logical Addresses          : 1 (Allow RC Passthrough)

	  Logical Address          : 0 (TV)
	    Primary Device Type    : TV
	    Logical Address Type   : TV
	    All Device Types       : TV
	    RC TV Profile          : None
	    Device Features        :
		None



Initial Event: State Change: PA: 0.0.0.0, LA mask: 0x0001, Conn Info: no
Received from Unregistered to TV (15 to 0): IMAGE_VIEW_ON (0x04)

So it looks like it's working as expected?

Maxime