linux-media.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Arnd Bergmann <arnd@kernel.org>
To: Sean Young <sean@mess.org>, Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Hans Verkuil <hverkuil-cisco@xs4all.nl>,
	linux-media@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 2/2] media: rc: clean up Kconfig dependencies
Date: Wed, 21 Apr 2021 15:58:41 +0200	[thread overview]
Message-ID: <20210421135935.3653827-2-arnd@kernel.org> (raw)
In-Reply-To: <20210421135935.3653827-1-arnd@kernel.org>

From: Arnd Bergmann <arnd@arndb.de>

I came across a randconfig build failure from one driver
that only depends on CONFIG_USB_ARCH_HAS_HCD but fails when
built without CONFIG_USB:

ld: drivers/media/rc/ir_toy.o: in function `irtoy_disconnect':
ir_toy.c:(.text+0x24): undefined reference to `usb_kill_urb'
ld: ir_toy.c:(.text+0x2c): undefined reference to `usb_free_urb'
ld: ir_toy.c:(.text+0x34): undefined reference to `usb_kill_urb'
ld: ir_toy.c:(.text+0x3c): undefined reference to `usb_free_urb'

Upon a closer look, I find that a lot of the other drivers
'select USB' rather than stating 'depends on USB' as is common
for most subsystems. I also find that all except one driver
have an extra 'depends on RC_CORE' that is already implied by
the top-level 'if RC_CORE' check.

Clean up both by reducing the dependencies to the required set.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/media/rc/Kconfig | 73 ++++++----------------------------------
 1 file changed, 11 insertions(+), 62 deletions(-)

diff --git a/drivers/media/rc/Kconfig b/drivers/media/rc/Kconfig
index ae0025fba21c..d0a8326b75c2 100644
--- a/drivers/media/rc/Kconfig
+++ b/drivers/media/rc/Kconfig
@@ -19,7 +19,6 @@ source "drivers/media/rc/keymaps/Kconfig"
 
 config LIRC
 	bool "LIRC user interface"
-	depends on RC_CORE
 	help
 	   Enable this option to enable the Linux Infrared Remote
 	   Control user interface (e.g. /dev/lirc*). This interface
@@ -41,12 +40,10 @@ config BPF_LIRC_MODE2
 
 menuconfig RC_DECODERS
 	bool "Remote controller decoders"
-	depends on RC_CORE
 
 if RC_DECODERS
 config IR_NEC_DECODER
 	tristate "Enable IR raw decoder for the NEC protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -55,7 +52,6 @@ config IR_NEC_DECODER
 
 config IR_RC5_DECODER
 	tristate "Enable IR raw decoder for the RC-5 protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -64,7 +60,6 @@ config IR_RC5_DECODER
 
 config IR_RC6_DECODER
 	tristate "Enable IR raw decoder for the RC6 protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -73,7 +68,6 @@ config IR_RC6_DECODER
 
 config IR_JVC_DECODER
 	tristate "Enable IR raw decoder for the JVC protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -82,7 +76,6 @@ config IR_JVC_DECODER
 
 config IR_SONY_DECODER
 	tristate "Enable IR raw decoder for the Sony protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -91,7 +84,6 @@ config IR_SONY_DECODER
 
 config IR_SANYO_DECODER
 	tristate "Enable IR raw decoder for the Sanyo protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -101,7 +93,6 @@ config IR_SANYO_DECODER
 
 config IR_SHARP_DECODER
 	tristate "Enable IR raw decoder for the Sharp protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -111,7 +102,6 @@ config IR_SHARP_DECODER
 
 config IR_MCE_KBD_DECODER
 	tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -121,7 +111,6 @@ config IR_MCE_KBD_DECODER
 
 config IR_XMP_DECODER
 	tristate "Enable IR raw decoder for the XMP protocol"
-	depends on RC_CORE
 	select BITREVERSE
 
 	help
@@ -130,7 +119,6 @@ config IR_XMP_DECODER
 
 config IR_IMON_DECODER
 	tristate "Enable IR raw decoder for the iMON protocol"
-	depends on RC_CORE
 	help
 	   Enable this option if you have iMON PAD or Antec Veris infrared
 	   remote control and you would like to use it with a raw IR
@@ -138,7 +126,6 @@ config IR_IMON_DECODER
 
 config IR_RCMM_DECODER
 	tristate "Enable IR raw decoder for the RC-MM protocol"
-	depends on RC_CORE
 	help
 	   Enable this option when you have IR with RC-MM protocol, and
 	   you need the software decoder. The driver supports 12,
@@ -153,15 +140,12 @@ endif #RC_DECODERS
 
 menuconfig RC_DEVICES
 	bool "Remote Controller devices"
-	depends on RC_CORE
 
 if RC_DEVICES
 
 config RC_ATI_REMOTE
 	tristate "ATI / X10 based USB RF remote controls"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use an X10 based USB remote control.
 	   These are RF remotes with USB receivers.
@@ -179,7 +163,6 @@ config RC_ATI_REMOTE
 config IR_ENE
 	tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
 	depends on PNP || COMPILE_TEST
-	depends on RC_CORE
 	help
 	   Say Y here to enable support for integrated infrared receiver
 	   /transceiver made by ENE.
@@ -192,7 +175,6 @@ config IR_ENE
 
 config IR_HIX5HD2
 	tristate "Hisilicon hix5hd2 IR remote control"
-	depends on RC_CORE
 	depends on OF || COMPILE_TEST
 	help
 	   Say Y here if you want to use hisilicon hix5hd2 remote control.
@@ -203,9 +185,7 @@ config IR_HIX5HD2
 
 config IR_IMON
 	tristate "SoundGraph iMON Receiver and Display"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use a SoundGraph iMON (aka Antec Veris)
 	   IR Receiver and/or LCD/VFD/VGA display.
@@ -215,9 +195,7 @@ config IR_IMON
 
 config IR_IMON_RAW
 	tristate "SoundGraph iMON Receiver (early raw IR models)"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use a SoundGraph iMON IR Receiver,
 	   early raw models.
@@ -227,9 +205,7 @@ config IR_IMON_RAW
 
 config IR_MCEUSB
 	tristate "Windows Media Center Ed. eHome Infrared Transceiver"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use a Windows Media Center Edition
 	   eHome Infrared Transceiver.
@@ -240,7 +216,6 @@ config IR_MCEUSB
 config IR_ITE_CIR
 	tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver"
 	depends on PNP || COMPILE_TEST
-	depends on RC_CORE
 	help
 	   Say Y here to enable support for integrated infrared receivers
 	   /transceivers made by ITE Tech Inc. These are found in
@@ -253,7 +228,6 @@ config IR_ITE_CIR
 config IR_FINTEK
 	tristate "Fintek Consumer Infrared Transceiver"
 	depends on PNP || COMPILE_TEST
-	depends on RC_CORE
 	help
 	   Say Y here to enable support for integrated infrared receiver
 	   /transceiver made by Fintek. This chip is found on assorted
@@ -264,7 +238,6 @@ config IR_FINTEK
 
 config IR_MESON
 	tristate "Amlogic Meson IR remote receiver"
-	depends on RC_CORE
 	depends on ARCH_MESON || COMPILE_TEST
 	help
 	   Say Y if you want to use the IR remote receiver available
@@ -275,7 +248,6 @@ config IR_MESON
 
 config IR_MTK
 	tristate "Mediatek IR remote receiver"
-	depends on RC_CORE
 	depends on ARCH_MEDIATEK || COMPILE_TEST
 	help
 	   Say Y if you want to use the IR remote receiver available
@@ -287,7 +259,6 @@ config IR_MTK
 config IR_NUVOTON
 	tristate "Nuvoton w836x7hg Consumer Infrared Transceiver"
 	depends on PNP || COMPILE_TEST
-	depends on RC_CORE
 	help
 	   Say Y here to enable support for integrated infrared receiver
 	   /transceiver made by Nuvoton (formerly Winbond). This chip is
@@ -299,11 +270,9 @@ config IR_NUVOTON
 
 config IR_REDRAT3
 	tristate "RedRat3 IR Transceiver"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
+	depends on USB
 	select NEW_LEDS
 	select LEDS_CLASS
-	select USB
 	help
 	   Say Y here if you want to use a RedRat3 Infrared Transceiver.
 
@@ -322,9 +291,7 @@ config IR_SPI
 
 config IR_STREAMZAP
 	tristate "Streamzap PC Remote IR Receiver"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use a Streamzap PC Remote
 	   Infrared Receiver.
@@ -335,7 +302,6 @@ config IR_STREAMZAP
 config IR_WINBOND_CIR
 	tristate "Winbond IR remote control"
 	depends on (X86 && PNP) || COMPILE_TEST
-	depends on RC_CORE
 	select NEW_LEDS
 	select LEDS_CLASS
 	select BITREVERSE
@@ -350,9 +316,7 @@ config IR_WINBOND_CIR
 
 config IR_IGORPLUGUSB
 	tristate "IgorPlug-USB IR Receiver"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use the IgorPlug-USB IR Receiver by
 	   Igor Cesko. This device is included on the Fit-PC2.
@@ -365,9 +329,7 @@ config IR_IGORPLUGUSB
 
 config IR_IGUANA
 	tristate "IguanaWorks USB IR Transceiver"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use the IguanaWorks USB IR Transceiver.
 	   Both infrared receive and send are supported. If you want to
@@ -381,9 +343,7 @@ config IR_IGUANA
 
 config IR_TTUSBIR
 	tristate "TechnoTrend USB IR Receiver"
-	depends on USB_ARCH_HAS_HCD
-	depends on RC_CORE
-	select USB
+	depends on USB
 	select NEW_LEDS
 	select LEDS_CLASS
 	help
@@ -407,7 +367,6 @@ source "drivers/media/rc/img-ir/Kconfig"
 
 config RC_LOOPBACK
 	tristate "Remote Control Loopback Driver"
-	depends on RC_CORE
 	help
 	   Say Y here if you want support for the remote control loopback
 	   driver which allows TX data to be sent back as RX data.
@@ -420,7 +379,6 @@ config RC_LOOPBACK
 
 config IR_GPIO_CIR
 	tristate "GPIO IR remote control"
-	depends on RC_CORE
 	depends on (OF && GPIOLIB) || COMPILE_TEST
 	help
 	   Say Y if you want to use GPIO based IR Receiver.
@@ -430,7 +388,6 @@ config IR_GPIO_CIR
 
 config IR_GPIO_TX
 	tristate "GPIO IR Bit Banging Transmitter"
-	depends on RC_CORE
 	depends on LIRC
 	depends on (OF && GPIOLIB) || COMPILE_TEST
 	help
@@ -442,7 +399,6 @@ config IR_GPIO_TX
 
 config IR_PWM_TX
 	tristate "PWM IR transmitter"
-	depends on RC_CORE
 	depends on LIRC
 	depends on PWM
 	depends on OF || COMPILE_TEST
@@ -455,7 +411,6 @@ config IR_PWM_TX
 
 config RC_ST
 	tristate "ST remote control receiver"
-	depends on RC_CORE
 	depends on ARCH_STI || COMPILE_TEST
 	help
 	   Say Y here if you want support for ST remote control driver
@@ -466,7 +421,6 @@ config RC_ST
 
 config IR_SUNXI
 	tristate "SUNXI IR remote control"
-	depends on RC_CORE
 	depends on ARCH_SUNXI || COMPILE_TEST
 	help
 	   Say Y if you want to use sunXi internal IR Controller
@@ -476,7 +430,6 @@ config IR_SUNXI
 
 config IR_SERIAL
 	tristate "Homebrew Serial Port Receiver"
-	depends on RC_CORE
 	help
 	   Say Y if you want to use Homebrew Serial Port Receivers and
 	   Transceivers.
@@ -492,7 +445,6 @@ config IR_SERIAL_TRANSMITTER
 
 config IR_SIR
 	tristate "Built-in SIR IrDA port"
-	depends on RC_CORE
 	help
 	   Say Y if you want to use a IrDA SIR port Transceivers.
 
@@ -501,9 +453,7 @@ config IR_SIR
 
 config RC_XBOX_DVD
 	tristate "Xbox DVD Movie Playback Kit"
-	depends on RC_CORE
-	depends on USB_ARCH_HAS_HCD
-	select USB
+	depends on USB
 	help
 	   Say Y here if you want to use the Xbox DVD Movie Playback Kit.
 	   These are IR remotes with USB receivers for the Original Xbox (2001).
@@ -513,8 +463,7 @@ config RC_XBOX_DVD
 
 config IR_TOY
 	tristate "Infrared Toy and IR Droid"
-	depends on RC_CORE
-	depends on USB_ARCH_HAS_HCD
+	depends on USB
 	help
 	   Say Y here if you want to use the Infrared Toy or IR Droid, USB
 	   versions.
-- 
2.29.2


  reply	other threads:[~2021-04-21 14:00 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-04-21 13:58 [PATCH 1/2] [v2] media: rc: remove tango ir driver and keymap Arnd Bergmann
2021-04-21 13:58 ` Arnd Bergmann [this message]
2021-04-24  6:34   ` [PATCH 2/2] media: rc: clean up Kconfig dependencies Randy Dunlap
2021-04-21 16:28 ` [PATCH 1/2] [v2] media: rc: remove tango ir driver and keymap Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210421135935.3653827-2-arnd@kernel.org \
    --to=arnd@kernel.org \
    --cc=arnd@arndb.de \
    --cc=gregkh@linuxfoundation.org \
    --cc=hverkuil-cisco@xs4all.nl \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=mchehab@kernel.org \
    --cc=sean@mess.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).