[PATCH v4 0/5] Add support for the Hynix Hi-846 camera

[PATCH v4 0/5] Add support for the Hynix Hi-846 camera

[Martin Kepplinger]

hi,

This patchset adds support for the SK Hynix Hi-846 CMOS images sensor.
It includes dt-bindings and the driver.

Patches 4 and 5 are basically optional: if i2c-cardlist is deprecated,
ignore it and act on it appropriately, and the arm64 defconfig is just
convenience for now.

best wishes,

                              martin

revision history
----------------
v4: (thank you Laurent, Sakari and Rob) many driver changes, see v3 review for
details. they include:
* add get_selection(), remove open() callback
* use gpiod API
* use regulator_bulk API
* fix power supply timing sequence and bindings

v3: (thank you, Laurent)
* use do_div() for divisions
* reset-gpios DT property name instead of rst-gpios
* improve the dt-bindings
* add the phone-devel list
* https://lore.kernel.org/linux-media/20210531120737.168496-1-martin.kepplinger@puri.sm/

v2:
sent a bit early due to stupid mistakes
* fix build issues
* fix dtschema issues
* add enable for arm64 defconfig
* https://lore.kernel.org/linux-media/20210530212337.GA15366@duo.ucw.cz/T/#t

v1:
* https://lore.kernel.org/linux-media/20210527091221.3335998-1-martin.kepplinger@puri.sm/


Martin Kepplinger (5):
  dt-bindings: vendor-prefixes: Add SK Hynix Inc.
  dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel
    sensor
  media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera
  arm64: defconfig: enable VIDEO_HI846
  Documentation: i2c-cardlist: add the Hynix hi846 sensor

 .../admin-guide/media/i2c-cardlist.rst        |    1 +
 .../bindings/media/i2c/hynix,hi846.yaml       |  105 +
 .../devicetree/bindings/vendor-prefixes.yaml  |    2 +
 MAINTAINERS                                   |    6 +
 arch/arm64/configs/defconfig                  |    1 +
 drivers/media/i2c/Kconfig                     |   13 +
 drivers/media/i2c/Makefile                    |    1 +
 drivers/media/i2c/hi846.c                     | 2117 +++++++++++++++++
 8 files changed, 2246 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
 create mode 100644 drivers/media/i2c/hi846.c

-- 
2.30.2

[PATCH v4 1/5] dt-bindings: vendor-prefixes: Add SK Hynix Inc.

[Martin Kepplinger]

SK Hynix built the already supported hi556 sensor (and probably much
more). For more information, see https://www.skhynix.com/

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 64429b128da4..5a74b009e64c 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -503,6 +503,8 @@ patternProperties:
     description: Hycon Technology Corp.
   "^hydis,.*":
     description: Hydis Technologies
+  "^hynix,.*":
+    description: SK Hynix Inc.
   "^hyundai,.*":
     description: Hyundai Technology
   "^i2se,.*":
-- 
2.30.2

[PATCH v4 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor

[Martin Kepplinger]

Document the bindings used for the SK Hynix Hi-846 CMOS camera driver.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
---
 .../bindings/media/i2c/hynix,hi846.yaml       | 105 ++++++++++++++++++
 1 file changed, 105 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml

diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
new file mode 100644
index 000000000000..19825392fb1f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
+
+maintainers:
+  - Martin Kepplinger <martin.kepplinger@puri.sm>
+
+description: |-
+  The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
+  interface and CCI (I2C compatible) control bus. The output format
+  is raw Bayer.
+
+properties:
+  compatible:
+    const: hynix,hi846
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Reference to the mclk clock.
+
+  reset-gpios:
+    description: Reference to the GPIO connected to the RESETB pin. Active low.
+    maxItems: 1
+
+  shutdown-gpios:
+    description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
+    maxItems: 1
+
+  vddi-supply:
+    description: Definition of the regulator used for the 1.8V or 2.8V I/O power supply.
+
+  vdda-supply:
+    description: Definition of the regulator used for the 2.8V analog power supply.
+
+  vddd-supply:
+    description: Definition of the regulator used for the 1.2V core power supply.
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            oneOf:
+              - items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+              - items:
+                  - const: 1
+                  - const: 2
+
+        required:
+          - data-lanes
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - vddi-supply
+  - vdda-supply
+  - vddd-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        hi846: camera@20 {
+            compatible = "hynix,hi846";
+            reg = <0x20>;
+            clocks = <&clk>;
+            vddi-supply = <&reg_camera_pwr_en>;
+            vdda-supply = <&reg_camera_pwr_en>;
+            vddd-supply = <&reg_camera_pwr_en>;
+            reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+
+            port {
+                camera_out: endpoint {
+                    remote-endpoint = <&csi1_ep1>;
+                    data-lanes = <1 2>;
+                };
+            };
+        };
+    };
+
+...
-- 
2.30.2

[PATCH v4 3/5] media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera

[Martin Kepplinger]

The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.

This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.

The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go

The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
---
 MAINTAINERS                |    6 +
 drivers/media/i2c/Kconfig  |   13 +
 drivers/media/i2c/Makefile |    1 +
 drivers/media/i2c/hi846.c  | 2117 ++++++++++++++++++++++++++++++++++++
 4 files changed, 2137 insertions(+)
 create mode 100644 drivers/media/i2c/hi846.c

diff --git a/MAINTAINERS b/MAINTAINERS
index a7667b5d0bc6..43ea93e92b0c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8517,6 +8517,12 @@ S:	Maintained
 T:	git git://linuxtv.org/media_tree.git
 F:	drivers/media/i2c/hi556.c
 
+HYNIX HI846 SENSOR DRIVER
+M:	Martin Kepplinger <martin.kepplinger@puri.sm>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	drivers/media/i2c/hi846.c
+
 Hyper-V/Azure CORE AND DRIVERS
 M:	"K. Y. Srinivasan" <kys@microsoft.com>
 M:	Haiyang Zhang <haiyangz@microsoft.com>
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 588f8eb95984..5b020d05960c 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -753,6 +753,19 @@ config VIDEO_IMX208
 	  To compile this driver as a module, choose M here: the
 	  module will be called imx208.
 
+config VIDEO_HI846
+	tristate "Hynix Hi-846 sensor support"
+	depends on I2C && VIDEO_V4L2
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select V4L2_FWNODE
+	help
+	  This is a Video4Linux2 sensor driver for the Hynix
+	  Hi-846 camera.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called hi846.
+
 config VIDEO_IMX214
 	tristate "Sony IMX214 sensor support"
 	depends on GPIOLIB && I2C && VIDEO_V4L2
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 1168fa6b84ed..303cd7bc4e66 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -116,6 +116,7 @@ obj-$(CONFIG_VIDEO_ML86V7667)	+= ml86v7667.o
 obj-$(CONFIG_VIDEO_OV2659)	+= ov2659.o
 obj-$(CONFIG_VIDEO_TC358743)	+= tc358743.o
 obj-$(CONFIG_VIDEO_HI556)	+= hi556.o
+obj-$(CONFIG_VIDEO_HI846)	+= hi846.o
 obj-$(CONFIG_VIDEO_IMX208)	+= imx208.o
 obj-$(CONFIG_VIDEO_IMX214)	+= imx214.o
 obj-$(CONFIG_VIDEO_IMX219)	+= imx219.o
diff --git a/drivers/media/i2c/hi846.c b/drivers/media/i2c/hi846.c
new file mode 100644
index 000000000000..87b8007f0557
--- /dev/null
+++ b/drivers/media/i2c/hi846.c
@@ -0,0 +1,2117 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2021 Purism SPC
+
+#include <asm/unaligned.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_graph.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm.h>
+#include <linux/regulator/consumer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+
+#define HI846_MEDIA_BUS_FORMAT		MEDIA_BUS_FMT_SGBRG10_1X10
+#define HI846_RGB_DEPTH			10
+
+/* Frame length lines / Vertical timings */
+#define HI846_REG_FLL			0x0006
+#define HI846_FLL_MAX			0xffff
+
+/* Horizontal timing */
+#define HI846_REG_LLP			0x0008
+#define HI846_LINE_LENGTH		3800
+
+#define HI846_REG_BINNING_MODE		0x000c
+
+#define HI846_REG_IMAGE_ORIENTATION	0x000e
+
+#define HI846_REG_UNKNOWN_0022		0x0022
+
+#define HI846_REG_Y_ADDR_START_VACT_H	0x0026
+#define HI846_REG_Y_ADDR_START_VACT_L	0x0027
+#define HI846_REG_UNKNOWN_0028		0x0028
+
+#define HI846_REG_Y_ADDR_END_VACT_H	0x002c
+#define HI846_REG_Y_ADDR_END_VACT_L	0x002d
+
+#define HI846_REG_Y_ODD_INC_FOBP	0x002e
+#define HI846_REG_Y_EVEN_INC_FOBP	0x002f
+
+#define HI846_REG_Y_ODD_INC_VACT	0x0032
+#define HI846_REG_Y_EVEN_INC_VACT	0x0033
+
+#define HI846_REG_GROUPED_PARA_HOLD	0x0046
+
+#define HI846_REG_TG_ENABLE		0x004c
+
+#define HI846_REG_UNKNOWN_005C		0x005c
+
+#define HI846_REG_UNKNOWN_006A		0x006a
+
+/*
+ * Long exposure time. Actually, exposure is a 20 bit value that
+ * includes the lower 4 bits of 0x0073 too. only 16 bit are used
+ * right now
+ */
+#define HI846_REG_EXPOSURE		0x0074
+#define HI846_EXPOSURE_MIN		6
+#define HI846_EXPOSURE_MAX_MARGIN	2
+#define HI846_EXPOSURE_STEP		1
+
+/* Analog gain controls from sensor */
+#define HI846_REG_ANALOG_GAIN		0x0077
+#define HI846_ANAL_GAIN_MIN		0
+#define HI846_ANAL_GAIN_MAX		240
+#define HI846_ANAL_GAIN_STEP		8
+
+/* Digital gain controls from sensor */
+#define HI846_REG_MWB_GR_GAIN_H		0x0078
+#define HI846_REG_MWB_GR_GAIN_L		0x0079
+#define HI846_REG_MWB_GB_GAIN_H		0x007a
+#define HI846_REG_MWB_GB_GAIN_L		0x007b
+#define HI846_REG_MWB_R_GAIN_H		0x007c
+#define HI846_REG_MWB_R_GAIN_L		0x007d
+#define HI846_REG_MWB_B_GAIN_H		0x007e
+#define HI846_REG_MWB_B_GAIN_L		0x007f
+#define HI846_DGTL_GAIN_MIN		0
+#define HI846_DGTL_GAIN_MAX		8191
+#define HI846_DGTL_GAIN_STEP		1
+#define HI846_DGTL_GAIN_DEFAULT		256
+
+#define HI846_REG_X_ADDR_START_HACT_H	0x0120
+#define HI846_REG_X_ADDR_END_HACT_H	0x0122
+
+#define HI846_REG_UNKNOWN_012A		0x012a
+
+#define HI846_REG_UNKNOWN_0200		0x0200
+
+#define HI846_REG_UNKNOWN_021C		0x021c
+#define HI846_REG_UNKNOWN_021E		0x021e
+
+#define HI846_REG_UNKNOWN_0402		0x0402
+#define HI846_REG_UNKNOWN_0404		0x0404
+#define HI846_REG_UNKNOWN_0408		0x0408
+#define HI846_REG_UNKNOWN_0410		0x0410
+#define HI846_REG_UNKNOWN_0412		0x0412
+#define HI846_REG_UNKNOWN_0414		0x0414
+
+#define HI846_REG_UNKNOWN_0418		0x0418
+
+#define HI846_REG_UNKNOWN_051E		0x051e
+
+/* Formatter */
+#define HI846_REG_X_START_H		0x0804
+#define HI846_REG_X_START_L		0x0805
+
+/* MIPI */
+#define HI846_REG_UNKNOWN_0900		0x0900
+#define HI846_REG_MIPI_TX_OP_EN		0x0901
+#define HI846_REG_MIPI_TX_OP_MODE	0x0902
+#define HI846_RAW8			BIT(5)
+
+#define HI846_REG_UNKNOWN_090C		0x090c
+#define HI846_REG_UNKNOWN_090E		0x090e
+
+#define HI846_REG_UNKNOWN_0914		0x0914
+#define HI846_REG_TLPX			0x0915
+#define HI846_REG_TCLK_PREPARE		0x0916
+#define HI846_REG_TCLK_ZERO		0x0917
+#define HI846_REG_UNKNOWN_0918		0x0918
+#define HI846_REG_THS_PREPARE		0x0919
+#define HI846_REG_THS_ZERO		0x091a
+#define HI846_REG_THS_TRAIL		0x091b
+#define HI846_REG_TCLK_POST		0x091c
+#define HI846_REG_TCLK_TRAIL_MIN	0x091d
+#define HI846_REG_UNKNOWN_091E		0x091e
+
+#define HI846_REG_UNKNOWN_0954		0x0954
+#define HI846_REG_UNKNOWN_0956		0x0956
+#define HI846_REG_UNKNOWN_0958		0x0958
+#define HI846_REG_UNKNOWN_095A		0x095a
+
+/* ISP Common */
+#define HI846_REG_MODE_SELECT		0x0a00
+#define HI846_MODE_STANDBY		0x00
+#define HI846_MODE_STREAMING		0x01
+#define HI846_REG_FAST_STANDBY_MODE	0x0a02
+#define HI846_REG_ISP_EN_H		0x0a04
+
+/* Test Pattern Control */
+#define HI846_REG_ISP			0x0a05
+#define HI846_REG_ISP_TPG_EN		0x01
+#define HI846_REG_TEST_PATTERN		0x020a /* 1-9 */
+
+#define HI846_REG_UNKNOWN_0A0C		0x0a0c
+
+/* Windowing */
+#define HI846_REG_X_OUTPUT_SIZE_H	0x0a12
+#define HI846_REG_X_OUTPUT_SIZE_L	0x0a13
+#define HI846_REG_Y_OUTPUT_SIZE_H	0x0a14
+#define HI846_REG_Y_OUTPUT_SIZE_L	0x0a15
+
+/* ISP Common */
+#define HI846_REG_PEDESTAL_EN		0x0a1a
+
+#define HI846_REG_UNKNOWN_0A1E		0x0a1e
+
+/* Horizontal Binning Mode */
+#define HI846_REG_HBIN_MODE		0x0a22
+
+#define HI846_REG_UNKNOWN_0A24		0x0a24
+#define HI846_REG_UNKNOWN_0B02		0x0b02
+#define HI846_REG_UNKNOWN_0B10		0x0b10
+#define HI846_REG_UNKNOWN_0B12		0x0b12
+#define HI846_REG_UNKNOWN_0B14		0x0b14
+
+/* BLC (Black Level Calibration) */
+#define HI846_REG_BLC_CTL0		0x0c00
+
+#define HI846_REG_UNKNOWN_0C06		0x0c06
+#define HI846_REG_UNKNOWN_0C10		0x0c10
+#define HI846_REG_UNKNOWN_0C12		0x0c12
+#define HI846_REG_UNKNOWN_0C14		0x0c14
+#define HI846_REG_UNKNOWN_0C16		0x0c16
+
+#define HI846_REG_UNKNOWN_0E04		0x0e04
+
+#define HI846_REG_CHIP_ID_L		0x0f16
+#define HI846_REG_CHIP_ID_H		0x0f17
+#define HI846_CHIP_ID_L			0x46
+#define HI846_CHIP_ID_H			0x08
+
+#define HI846_REG_UNKNOWN_0F04		0x0f04
+#define HI846_REG_UNKNOWN_0F08		0x0f08
+
+/* PLL */
+#define HI846_REG_PLL_CFG_MIPI2_H	0x0f2a
+#define HI846_REG_PLL_CFG_MIPI2_L	0x0f2b
+
+#define HI846_REG_UNKNOWN_0F30		0x0f30
+#define HI846_REG_PLL_CFG_RAMP1_H	0x0f32
+#define HI846_REG_UNKNOWN_0F36		0x0f36
+#define HI846_REG_PLL_CFG_MIPI1_H	0x0f38
+
+#define HI846_REG_UNKNOWN_2008		0x2008
+#define HI846_REG_UNKNOWN_326E		0x326e
+
+struct hi846_reg {
+	u16 address;
+	u16 val;
+};
+
+struct hi846_reg_list {
+	u32 num_of_regs;
+	const struct hi846_reg *regs;
+};
+
+struct hi846_mode {
+	/* Frame width in pixels */
+	u32 width;
+
+	/* Frame height in pixels */
+	u32 height;
+
+	/* Horizontal timing size */
+	u32 llp;
+
+	/* Link frequency needed for this resolution */
+	u8 link_freq_index;
+
+	u16 fps;
+
+	/* vertical timining size */
+	u16 frame_len;
+
+	const struct hi846_reg_list reg_list_config;
+	const struct hi846_reg_list reg_list_2lane;
+	const struct hi846_reg_list reg_list_4lane;
+
+	/* position inside of the 3264x2448 pixel array */
+	struct v4l2_rect crop;
+};
+
+static const struct hi846_reg hi846_init_2lane[] = {
+	{HI846_REG_MODE_SELECT,		0x0000},
+	/* regs below are unknown */
+	{0x2000, 0x100a},
+	{0x2002, 0x00ff},
+	{0x2004, 0x0007},
+	{0x2006, 0x3fff},
+	{0x2008, 0x3fff},
+	{0x200a, 0xc216},
+	{0x200c, 0x1292},
+	{0x200e, 0xc01a},
+	{0x2010, 0x403d},
+	{0x2012, 0x000e},
+	{0x2014, 0x403e},
+	{0x2016, 0x0b80},
+	{0x2018, 0x403f},
+	{0x201a, 0x82ae},
+	{0x201c, 0x1292},
+	{0x201e, 0xc00c},
+	{0x2020, 0x4130},
+	{0x2022, 0x43e2},
+	{0x2024, 0x0180},
+	{0x2026, 0x4130},
+	{0x2028, 0x7400},
+	{0x202a, 0x5000},
+	{0x202c, 0x0253},
+	{0x202e, 0x0ad1},
+	{0x2030, 0x2360},
+	{0x2032, 0x0009},
+	{0x2034, 0x5020},
+	{0x2036, 0x000b},
+	{0x2038, 0x0002},
+	{0x203a, 0x0044},
+	{0x203c, 0x0016},
+	{0x203e, 0x1792},
+	{0x2040, 0x7002},
+	{0x2042, 0x154f},
+	{0x2044, 0x00d5},
+	{0x2046, 0x000b},
+	{0x2048, 0x0019},
+	{0x204a, 0x1698},
+	{0x204c, 0x000e},
+	{0x204e, 0x099a},
+	{0x2050, 0x0058},
+	{0x2052, 0x7000},
+	{0x2054, 0x1799},
+	{0x2056, 0x0310},
+	{0x2058, 0x03c3},
+	{0x205a, 0x004c},
+	{0x205c, 0x064a},
+	{0x205e, 0x0001},
+	{0x2060, 0x0007},
+	{0x2062, 0x0bc7},
+	{0x2064, 0x0055},
+	{0x2066, 0x7000},
+	{0x2068, 0x1550},
+	{0x206a, 0x158a},
+	{0x206c, 0x0004},
+	{0x206e, 0x1488},
+	{0x2070, 0x7010},
+	{0x2072, 0x1508},
+	{0x2074, 0x0004},
+	{0x2076, 0x0016},
+	{0x2078, 0x03d5},
+	{0x207a, 0x0055},
+	{0x207c, 0x08ca},
+	{0x207e, 0x2019},
+	{0x2080, 0x0007},
+	{0x2082, 0x7057},
+	{0x2084, 0x0fc7},
+	{0x2086, 0x5041},
+	{0x2088, 0x12c8},
+	{0x208a, 0x5060},
+	{0x208c, 0x5080},
+	{0x208e, 0x2084},
+	{0x2090, 0x12c8},
+	{0x2092, 0x7800},
+	{0x2094, 0x0802},
+	{0x2096, 0x040f},
+	{0x2098, 0x1007},
+	{0x209a, 0x0803},
+	{0x209c, 0x080b},
+	{0x209e, 0x3803},
+	{0x20a0, 0x0807},
+	{0x20a2, 0x0404},
+	{0x20a4, 0x0400},
+	{0x20a6, 0xffff},
+	{0x20a8, 0xf0b2},
+	{0x20aa, 0xffef},
+	{0x20ac, 0x0a84},
+	{0x20ae, 0x1292},
+	{0x20b0, 0xc02e},
+	{0x20b2, 0x4130},
+	{0x23fe, 0xc056},
+	{0x3232, 0xfc0c},
+	{0x3236, 0xfc22},
+	{0x3248, 0xfca8},
+	{0x326a, 0x8302},
+	{0x326c, 0x830a},
+	{0x326e, 0x0000},
+	{0x32ca, 0xfc28},
+	{0x32cc, 0xc3bc},
+	{0x32ce, 0xc34c},
+	{0x32d0, 0xc35a},
+	{0x32d2, 0xc368},
+	{0x32d4, 0xc376},
+	{0x32d6, 0xc3c2},
+	{0x32d8, 0xc3e6},
+	{0x32da, 0x0003},
+	{0x32dc, 0x0003},
+	{0x32de, 0x00c7},
+	{0x32e0, 0x0031},
+	{0x32e2, 0x0031},
+	{0x32e4, 0x0031},
+	{0x32e6, 0xfc28},
+	{0x32e8, 0xc3bc},
+	{0x32ea, 0xc384},
+	{0x32ec, 0xc392},
+	{0x32ee, 0xc3a0},
+	{0x32f0, 0xc3ae},
+	{0x32f2, 0xc3c4},
+	{0x32f4, 0xc3e6},
+	{0x32f6, 0x0003},
+	{0x32f8, 0x0003},
+	{0x32fa, 0x00c7},
+	{0x32fc, 0x0031},
+	{0x32fe, 0x0031},
+	{0x3300, 0x0031},
+	{0x3302, 0x82ca},
+	{0x3304, 0xc164},
+	{0x3306, 0x82e6},
+	{0x3308, 0xc19c},
+	{0x330a, 0x001f},
+	{0x330c, 0x001a},
+	{0x330e, 0x0034},
+	{0x3310, 0x0000},
+	{0x3312, 0x0000},
+	{0x3314, 0xfc94},
+	{0x3316, 0xc3d8},
+	/* regs above are unknown */
+	{HI846_REG_MODE_SELECT,			0x0000},
+	{HI846_REG_UNKNOWN_0E04,		0x0012},
+	{HI846_REG_Y_ODD_INC_FOBP,		0x1111},
+	{HI846_REG_Y_ODD_INC_VACT,		0x1111},
+	{HI846_REG_UNKNOWN_0022,		0x0008},
+	{HI846_REG_Y_ADDR_START_VACT_H,		0x0040},
+	{HI846_REG_UNKNOWN_0028,		0x0017},
+	{HI846_REG_Y_ADDR_END_VACT_H,		0x09cf},
+	{HI846_REG_UNKNOWN_005C,		0x2101},
+	{HI846_REG_FLL,				0x09de},
+	{HI846_REG_LLP,				0x0ed8},
+	{HI846_REG_IMAGE_ORIENTATION,		0x0100},
+	{HI846_REG_BINNING_MODE,		0x0022},
+	{HI846_REG_HBIN_MODE,			0x0000},
+	{HI846_REG_UNKNOWN_0A24,		0x0000},
+	{HI846_REG_X_START_H,			0x0000},
+	{HI846_REG_X_OUTPUT_SIZE_H,		0x0cc0},
+	{HI846_REG_Y_OUTPUT_SIZE_H,		0x0990},
+	{HI846_REG_EXPOSURE,			0x09d8},
+	{HI846_REG_ANALOG_GAIN,			0x0000},
+	{HI846_REG_GROUPED_PARA_HOLD,		0x0000},
+	{HI846_REG_UNKNOWN_051E,		0x0000},
+	{HI846_REG_UNKNOWN_0200,		0x0400},
+	{HI846_REG_PEDESTAL_EN,			0x0c00},
+	{HI846_REG_UNKNOWN_0A0C,		0x0010},
+	{HI846_REG_UNKNOWN_0A1E,		0x0ccf},
+	{HI846_REG_UNKNOWN_0402,		0x0110},
+	{HI846_REG_UNKNOWN_0404,		0x00f4},
+	{HI846_REG_UNKNOWN_0408,		0x0000},
+	{HI846_REG_UNKNOWN_0410,		0x008d},
+	{HI846_REG_UNKNOWN_0412,		0x011a},
+	{HI846_REG_UNKNOWN_0414,		0x864c},
+	{HI846_REG_UNKNOWN_021C,		0x0003},
+	{HI846_REG_UNKNOWN_021E,		0x0235},
+	{HI846_REG_BLC_CTL0,			0x9150},
+	{HI846_REG_UNKNOWN_0C06,		0x0021},
+	{HI846_REG_UNKNOWN_0C10,		0x0040},
+	{HI846_REG_UNKNOWN_0C12,		0x0040},
+	{HI846_REG_UNKNOWN_0C14,		0x0040},
+	{HI846_REG_UNKNOWN_0C16,		0x0040},
+	{HI846_REG_FAST_STANDBY_MODE,		0x0100},
+	{HI846_REG_ISP_EN_H,			0x014a},
+	{HI846_REG_UNKNOWN_0418,		0x0000},
+	{HI846_REG_UNKNOWN_012A,		0x03b4},
+	{HI846_REG_X_ADDR_START_HACT_H,		0x0046},
+	{HI846_REG_X_ADDR_END_HACT_H,		0x0376},
+	{HI846_REG_UNKNOWN_0B02,		0xe04d},
+	{HI846_REG_UNKNOWN_0B10,		0x6821},
+	{HI846_REG_UNKNOWN_0B12,		0x0120},
+	{HI846_REG_UNKNOWN_0B14,		0x0001},
+	{HI846_REG_UNKNOWN_2008,		0x38fd},
+	{HI846_REG_UNKNOWN_326E,		0x0000},
+	{HI846_REG_UNKNOWN_0900,		0x0320},
+	{HI846_REG_MIPI_TX_OP_MODE,		0xc31a},
+	{HI846_REG_UNKNOWN_0914,		0xc109},
+	{HI846_REG_TCLK_PREPARE,		0x061a},
+	{HI846_REG_UNKNOWN_0918,		0x0306},
+	{HI846_REG_THS_ZERO,			0x0b09},
+	{HI846_REG_TCLK_POST,			0x0c07},
+	{HI846_REG_UNKNOWN_091E,		0x0a00},
+	{HI846_REG_UNKNOWN_090C,		0x042a},
+	{HI846_REG_UNKNOWN_090E,		0x006b},
+	{HI846_REG_UNKNOWN_0954,		0x0089},
+	{HI846_REG_UNKNOWN_0956,		0x0000},
+	{HI846_REG_UNKNOWN_0958,		0xca00},
+	{HI846_REG_UNKNOWN_095A,		0x9240},
+	{HI846_REG_UNKNOWN_0F08,		0x2f04},
+	{HI846_REG_UNKNOWN_0F30,		0x001f},
+	{HI846_REG_UNKNOWN_0F36,		0x001f},
+	{HI846_REG_UNKNOWN_0F04,		0x3a00},
+	{HI846_REG_PLL_CFG_RAMP1_H,		0x025a},
+	{HI846_REG_PLL_CFG_MIPI1_H,		0x025a},
+	{HI846_REG_PLL_CFG_MIPI2_H,		0x0024},
+	{HI846_REG_UNKNOWN_006A,		0x0100},
+	{HI846_REG_TG_ENABLE,			0x0100},
+};
+
+static const struct hi846_reg hi846_init_4lane[] = {
+	{0x2000, 0x987a},
+	{0x2002, 0x00ff},
+	{0x2004, 0x0047},
+	{0x2006, 0x3fff},
+	{0x2008, 0x3fff},
+	{0x200a, 0xc216},
+	{0x200c, 0x1292},
+	{0x200e, 0xc01a},
+	{0x2010, 0x403d},
+	{0x2012, 0x000e},
+	{0x2014, 0x403e},
+	{0x2016, 0x0b80},
+	{0x2018, 0x403f},
+	{0x201a, 0x82ae},
+	{0x201c, 0x1292},
+	{0x201e, 0xc00c},
+	{0x2020, 0x4130},
+	{0x2022, 0x43e2},
+	{0x2024, 0x0180},
+	{0x2026, 0x4130},
+	{0x2028, 0x7400},
+	{0x202a, 0x5000},
+	{0x202c, 0x0253},
+	{0x202e, 0x0ad1},
+	{0x2030, 0x2360},
+	{0x2032, 0x0009},
+	{0x2034, 0x5020},
+	{0x2036, 0x000b},
+	{0x2038, 0x0002},
+	{0x203a, 0x0044},
+	{0x203c, 0x0016},
+	{0x203e, 0x1792},
+	{0x2040, 0x7002},
+	{0x2042, 0x154f},
+	{0x2044, 0x00d5},
+	{0x2046, 0x000b},
+	{0x2048, 0x0019},
+	{0x204a, 0x1698},
+	{0x204c, 0x000e},
+	{0x204e, 0x099a},
+	{0x2050, 0x0058},
+	{0x2052, 0x7000},
+	{0x2054, 0x1799},
+	{0x2056, 0x0310},
+	{0x2058, 0x03c3},
+	{0x205a, 0x004c},
+	{0x205c, 0x064a},
+	{0x205e, 0x0001},
+	{0x2060, 0x0007},
+	{0x2062, 0x0bc7},
+	{0x2064, 0x0055},
+	{0x2066, 0x7000},
+	{0x2068, 0x1550},
+	{0x206a, 0x158a},
+	{0x206c, 0x0004},
+	{0x206e, 0x1488},
+	{0x2070, 0x7010},
+	{0x2072, 0x1508},
+	{0x2074, 0x0004},
+	{0x2076, 0x0016},
+	{0x2078, 0x03d5},
+	{0x207a, 0x0055},
+	{0x207c, 0x08ca},
+	{0x207e, 0x2019},
+	{0x2080, 0x0007},
+	{0x2082, 0x7057},
+	{0x2084, 0x0fc7},
+	{0x2086, 0x5041},
+	{0x2088, 0x12c8},
+	{0x208a, 0x5060},
+	{0x208c, 0x5080},
+	{0x208e, 0x2084},
+	{0x2090, 0x12c8},
+	{0x2092, 0x7800},
+	{0x2094, 0x0802},
+	{0x2096, 0x040f},
+	{0x2098, 0x1007},
+	{0x209a, 0x0803},
+	{0x209c, 0x080b},
+	{0x209e, 0x3803},
+	{0x20a0, 0x0807},
+	{0x20a2, 0x0404},
+	{0x20a4, 0x0400},
+	{0x20a6, 0xffff},
+	{0x20a8, 0xf0b2},
+	{0x20aa, 0xffef},
+	{0x20ac, 0x0a84},
+	{0x20ae, 0x1292},
+	{0x20b0, 0xc02e},
+	{0x20b2, 0x4130},
+	{0x20b4, 0xf0b2},
+	{0x20b6, 0xffbf},
+	{0x20b8, 0x2004},
+	{0x20ba, 0x403f},
+	{0x20bc, 0x00c3},
+	{0x20be, 0x4fe2},
+	{0x20c0, 0x8318},
+	{0x20c2, 0x43cf},
+	{0x20c4, 0x0000},
+	{0x20c6, 0x9382},
+	{0x20c8, 0xc314},
+	{0x20ca, 0x2003},
+	{0x20cc, 0x12b0},
+	{0x20ce, 0xcab0},
+	{0x20d0, 0x4130},
+	{0x20d2, 0x12b0},
+	{0x20d4, 0xc90a},
+	{0x20d6, 0x4130},
+	{0x20d8, 0x42d2},
+	{0x20da, 0x8318},
+	{0x20dc, 0x00c3},
+	{0x20de, 0x9382},
+	{0x20e0, 0xc314},
+	{0x20e2, 0x2009},
+	{0x20e4, 0x120b},
+	{0x20e6, 0x120a},
+	{0x20e8, 0x1209},
+	{0x20ea, 0x1208},
+	{0x20ec, 0x1207},
+	{0x20ee, 0x1206},
+	{0x20f0, 0x4030},
+	{0x20f2, 0xc15e},
+	{0x20f4, 0x4130},
+	{0x20f6, 0x1292},
+	{0x20f8, 0xc008},
+	{0x20fa, 0x4130},
+	{0x20fc, 0x42d2},
+	{0x20fe, 0x82a1},
+	{0x2100, 0x00c2},
+	{0x2102, 0x1292},
+	{0x2104, 0xc040},
+	{0x2106, 0x4130},
+	{0x2108, 0x1292},
+	{0x210a, 0xc006},
+	{0x210c, 0x42a2},
+	{0x210e, 0x7324},
+	{0x2110, 0x9382},
+	{0x2112, 0xc314},
+	{0x2114, 0x2011},
+	{0x2116, 0x425f},
+	{0x2118, 0x82a1},
+	{0x211a, 0xf25f},
+	{0x211c, 0x00c1},
+	{0x211e, 0xf35f},
+	{0x2120, 0x2406},
+	{0x2122, 0x425f},
+	{0x2124, 0x00c0},
+	{0x2126, 0xf37f},
+	{0x2128, 0x522f},
+	{0x212a, 0x4f82},
+	{0x212c, 0x7324},
+	{0x212e, 0x425f},
+	{0x2130, 0x82d4},
+	{0x2132, 0xf35f},
+	{0x2134, 0x4fc2},
+	{0x2136, 0x01b3},
+	{0x2138, 0x93c2},
+	{0x213a, 0x829f},
+	{0x213c, 0x2421},
+	{0x213e, 0x403e},
+	{0x2140, 0xfffe},
+	{0x2142, 0x40b2},
+	{0x2144, 0xec78},
+	{0x2146, 0x831c},
+	{0x2148, 0x40b2},
+	{0x214a, 0xec78},
+	{0x214c, 0x831e},
+	{0x214e, 0x40b2},
+	{0x2150, 0xec78},
+	{0x2152, 0x8320},
+	{0x2154, 0xb3d2},
+	{0x2156, 0x008c},
+	{0x2158, 0x2405},
+	{0x215a, 0x4e0f},
+	{0x215c, 0x503f},
+	{0x215e, 0xffd8},
+	{0x2160, 0x4f82},
+	{0x2162, 0x831c},
+	{0x2164, 0x90f2},
+	{0x2166, 0x0003},
+	{0x2168, 0x008c},
+	{0x216a, 0x2401},
+	{0x216c, 0x4130},
+	{0x216e, 0x421f},
+	{0x2170, 0x831c},
+	{0x2172, 0x5e0f},
+	{0x2174, 0x4f82},
+	{0x2176, 0x831e},
+	{0x2178, 0x5e0f},
+	{0x217a, 0x4f82},
+	{0x217c, 0x8320},
+	{0x217e, 0x3ff6},
+	{0x2180, 0x432e},
+	{0x2182, 0x3fdf},
+	{0x2184, 0x421f},
+	{0x2186, 0x7100},
+	{0x2188, 0x4f0e},
+	{0x218a, 0x503e},
+	{0x218c, 0xffd8},
+	{0x218e, 0x4e82},
+	{0x2190, 0x7a04},
+	{0x2192, 0x421e},
+	{0x2194, 0x831c},
+	{0x2196, 0x5f0e},
+	{0x2198, 0x4e82},
+	{0x219a, 0x7a06},
+	{0x219c, 0x0b00},
+	{0x219e, 0x7304},
+	{0x21a0, 0x0050},
+	{0x21a2, 0x40b2},
+	{0x21a4, 0xd081},
+	{0x21a6, 0x0b88},
+	{0x21a8, 0x421e},
+	{0x21aa, 0x831e},
+	{0x21ac, 0x5f0e},
+	{0x21ae, 0x4e82},
+	{0x21b0, 0x7a0e},
+	{0x21b2, 0x521f},
+	{0x21b4, 0x8320},
+	{0x21b6, 0x4f82},
+	{0x21b8, 0x7a10},
+	{0x21ba, 0x0b00},
+	{0x21bc, 0x7304},
+	{0x21be, 0x007a},
+	{0x21c0, 0x40b2},
+	{0x21c2, 0x0081},
+	{0x21c4, 0x0b88},
+	{0x21c6, 0x4392},
+	{0x21c8, 0x7a0a},
+	{0x21ca, 0x0800},
+	{0x21cc, 0x7a0c},
+	{0x21ce, 0x0b00},
+	{0x21d0, 0x7304},
+	{0x21d2, 0x022b},
+	{0x21d4, 0x40b2},
+	{0x21d6, 0xd081},
+	{0x21d8, 0x0b88},
+	{0x21da, 0x0b00},
+	{0x21dc, 0x7304},
+	{0x21de, 0x0255},
+	{0x21e0, 0x40b2},
+	{0x21e2, 0x0081},
+	{0x21e4, 0x0b88},
+	{0x21e6, 0x4130},
+	{0x23fe, 0xc056},
+	{0x3232, 0xfc0c},
+	{0x3236, 0xfc22},
+	{0x3238, 0xfcfc},
+	{0x323a, 0xfd84},
+	{0x323c, 0xfd08},
+	{0x3246, 0xfcd8},
+	{0x3248, 0xfca8},
+	{0x324e, 0xfcb4},
+	{0x326a, 0x8302},
+	{0x326c, 0x830a},
+	{0x326e, 0x0000},
+	{0x32ca, 0xfc28},
+	{0x32cc, 0xc3bc},
+	{0x32ce, 0xc34c},
+	{0x32d0, 0xc35a},
+	{0x32d2, 0xc368},
+	{0x32d4, 0xc376},
+	{0x32d6, 0xc3c2},
+	{0x32d8, 0xc3e6},
+	{0x32da, 0x0003},
+	{0x32dc, 0x0003},
+	{0x32de, 0x00c7},
+	{0x32e0, 0x0031},
+	{0x32e2, 0x0031},
+	{0x32e4, 0x0031},
+	{0x32e6, 0xfc28},
+	{0x32e8, 0xc3bc},
+	{0x32ea, 0xc384},
+	{0x32ec, 0xc392},
+	{0x32ee, 0xc3a0},
+	{0x32f0, 0xc3ae},
+	{0x32f2, 0xc3c4},
+	{0x32f4, 0xc3e6},
+	{0x32f6, 0x0003},
+	{0x32f8, 0x0003},
+	{0x32fa, 0x00c7},
+	{0x32fc, 0x0031},
+	{0x32fe, 0x0031},
+	{0x3300, 0x0031},
+	{0x3302, 0x82ca},
+	{0x3304, 0xc164},
+	{0x3306, 0x82e6},
+	{0x3308, 0xc19c},
+	{0x330a, 0x001f},
+	{0x330c, 0x001a},
+	{0x330e, 0x0034},
+	{0x3310, 0x0000},
+	{0x3312, 0x0000},
+	{0x3314, 0xfc94},
+	{0x3316, 0xc3d8},
+
+	{0x0a00, 0x0000},
+	{0x0e04, 0x0012},
+	{0x002e, 0x1111},
+	{0x0032, 0x1111},
+	{0x0022, 0x0008},
+	{0x0026, 0x0040},
+	{0x0028, 0x0017},
+	{0x002c, 0x09cf},
+	{0x005c, 0x2101},
+	{0x0006, 0x09de},
+	{0x0008, 0x0ed8},
+	{0x000e, 0x0100},
+	{0x000c, 0x0022},
+	{0x0a22, 0x0000},
+	{0x0a24, 0x0000},
+	{0x0804, 0x0000},
+	{0x0a12, 0x0cc0},
+	{0x0a14, 0x0990},
+	{0x0074, 0x09d8},
+	{0x0076, 0x0000},
+	{0x051e, 0x0000},
+	{0x0200, 0x0400},
+	{0x0a1a, 0x0c00},
+	{0x0a0c, 0x0010},
+	{0x0a1e, 0x0ccf},
+	{0x0402, 0x0110},
+	{0x0404, 0x00f4},
+	{0x0408, 0x0000},
+	{0x0410, 0x008d},
+	{0x0412, 0x011a},
+	{0x0414, 0x864c},
+	/* for OTP */
+	{0x021c, 0x0003},
+	{0x021e, 0x0235},
+	/* for OTP */
+	{0x0c00, 0x9950},
+	{0x0c06, 0x0021},
+	{0x0c10, 0x0040},
+	{0x0c12, 0x0040},
+	{0x0c14, 0x0040},
+	{0x0c16, 0x0040},
+	{0x0a02, 0x0100},
+	{0x0a04, 0x015a},
+	{0x0418, 0x0000},
+	{0x0128, 0x0028},
+	{0x012a, 0xffff},
+	{0x0120, 0x0046},
+	{0x0122, 0x0376},
+	{0x012c, 0x0020},
+	{0x012e, 0xffff},
+	{0x0124, 0x0040},
+	{0x0126, 0x0378},
+	{0x0746, 0x0050},
+	{0x0748, 0x01d5},
+	{0x074a, 0x022b},
+	{0x074c, 0x03b0},
+	{0x0756, 0x043f},
+	{0x0758, 0x3f1d},
+	{0x0b02, 0xe04d},
+	{0x0b10, 0x6821},
+	{0x0b12, 0x0120},
+	{0x0b14, 0x0001},
+	{0x2008, 0x38fd},
+	{0x326e, 0x0000},
+	{0x0900, 0x0300},
+	{0x0902, 0xc319},
+	{0x0914, 0xc109},
+	{0x0916, 0x061a},
+	{0x0918, 0x0407},
+	{0x091a, 0x0a0b},
+	{0x091c, 0x0e08},
+	{0x091e, 0x0a00},
+	{0x090c, 0x0427},
+	{0x090e, 0x0059},
+	{0x0954, 0x0089},
+	{0x0956, 0x0000},
+	{0x0958, 0xca80},
+	{0x095a, 0x9240},
+	{0x0f08, 0x2f04},
+	{0x0f30, 0x001f},
+	{0x0f36, 0x001f},
+	{0x0f04, 0x3a00},
+	{0x0f32, 0x025a},
+	{0x0f38, 0x025a},
+	{0x0f2a, 0x4124},
+	{0x006a, 0x0100},
+	{0x004c, 0x0100},
+	{0x0044, 0x0001},
+};
+
+static const struct hi846_reg mode_640x480_config[] = {
+	{HI846_REG_MODE_SELECT,			0x0000},
+	{HI846_REG_Y_ODD_INC_FOBP,		0x7711},
+	{HI846_REG_Y_ODD_INC_VACT,		0x7711},
+	{HI846_REG_Y_ADDR_START_VACT_H,		0x0148},
+	{HI846_REG_Y_ADDR_END_VACT_H,		0x08c7},
+	{HI846_REG_UNKNOWN_005C,		0x4404},
+	{HI846_REG_FLL,				0x0277},
+	{HI846_REG_LLP,				0x0ed8},
+	{HI846_REG_BINNING_MODE,		0x0322},
+	{HI846_REG_HBIN_MODE,			0x0200},
+	{HI846_REG_UNKNOWN_0A24,		0x0000},
+	{HI846_REG_X_START_H,			0x0058},
+	{HI846_REG_X_OUTPUT_SIZE_H,		0x0280},
+	{HI846_REG_Y_OUTPUT_SIZE_H,		0x01e0},
+
+	/* For OTP */
+	{HI846_REG_UNKNOWN_021C,		0x0003},
+	{HI846_REG_UNKNOWN_021E,		0x0235},
+
+	{HI846_REG_ISP_EN_H,			0x017a},
+	{HI846_REG_UNKNOWN_0418,		0x0210},
+	{HI846_REG_UNKNOWN_0B02,		0xe04d},
+	{HI846_REG_UNKNOWN_0B10,		0x7021},
+	{HI846_REG_UNKNOWN_0B12,		0x0120},
+	{HI846_REG_UNKNOWN_0B14,		0x0001},
+	{HI846_REG_UNKNOWN_2008,		0x38fd},
+	{HI846_REG_UNKNOWN_326E,		0x0000},
+};
+
+static const struct hi846_reg mode_640x480_mipi_2lane[] = {
+	{HI846_REG_UNKNOWN_0900,		0x0300},
+	{HI846_REG_MIPI_TX_OP_MODE,		0x4319},
+	{HI846_REG_UNKNOWN_0914,		0xc105},
+	{HI846_REG_TCLK_PREPARE,		0x030c},
+	{HI846_REG_UNKNOWN_0918,		0x0304},
+	{HI846_REG_THS_ZERO,			0x0708},
+	{HI846_REG_TCLK_POST,			0x0b04},
+	{HI846_REG_UNKNOWN_091E,		0x0500},
+	{HI846_REG_UNKNOWN_090C,		0x0208},
+	{HI846_REG_UNKNOWN_090E,		0x009a},
+	{HI846_REG_UNKNOWN_0954,		0x0089},
+	{HI846_REG_UNKNOWN_0956,		0x0000},
+	{HI846_REG_UNKNOWN_0958,		0xca80},
+	{HI846_REG_UNKNOWN_095A,		0x9240},
+	{HI846_REG_PLL_CFG_MIPI2_H,		0x4924},
+	{HI846_REG_TG_ENABLE,			0x0100},
+};
+
+static const struct hi846_reg mode_1280x720_config[] = {
+	{HI846_REG_MODE_SELECT,			0x0000},
+	{HI846_REG_Y_ODD_INC_FOBP,		0x3311},
+	{HI846_REG_Y_ODD_INC_VACT,		0x3311},
+	{HI846_REG_Y_ADDR_START_VACT_H,		0x0238},
+	{HI846_REG_Y_ADDR_END_VACT_H,		0x07d7},
+	{HI846_REG_UNKNOWN_005C,		0x4202},
+	{HI846_REG_FLL,				0x034a},
+	{HI846_REG_LLP,				0x0ed8},
+	{HI846_REG_BINNING_MODE,		0x0122},
+	{HI846_REG_HBIN_MODE,			0x0100},
+	{HI846_REG_UNKNOWN_0A24,		0x0000},
+	{HI846_REG_X_START_H,			0x00b0},
+	{HI846_REG_X_OUTPUT_SIZE_H,		0x0500},
+	{HI846_REG_Y_OUTPUT_SIZE_H,		0x02d0},
+	{HI846_REG_EXPOSURE,			0x0344},
+
+	/* For OTP */
+	{HI846_REG_UNKNOWN_021C,		0x0003},
+	{HI846_REG_UNKNOWN_021E,		0x0235},
+
+	{HI846_REG_ISP_EN_H,			0x017a},
+	{HI846_REG_UNKNOWN_0418,		0x0410},
+	{HI846_REG_UNKNOWN_0B02,		0xe04d},
+	{HI846_REG_UNKNOWN_0B10,		0x6c21},
+	{HI846_REG_UNKNOWN_0B12,		0x0120},
+	{HI846_REG_UNKNOWN_0B14,		0x0005},
+	{HI846_REG_UNKNOWN_2008,		0x38fd},
+	{HI846_REG_UNKNOWN_326E,		0x0000},
+};
+
+static const struct hi846_reg mode_1280x720_mipi_2lane[] = {
+	{HI846_REG_UNKNOWN_0900,		0x0300},
+	{HI846_REG_MIPI_TX_OP_MODE,		0x4319},
+	{HI846_REG_UNKNOWN_0914,		0xc109},
+	{HI846_REG_TCLK_PREPARE,		0x061a},
+	{HI846_REG_UNKNOWN_0918,		0x0407},
+	{HI846_REG_THS_ZERO,			0x0a0b},
+	{HI846_REG_TCLK_POST,			0x0e08},
+	{HI846_REG_UNKNOWN_091E,		0x0a00},
+	{HI846_REG_UNKNOWN_090C,		0x0427},
+	{HI846_REG_UNKNOWN_090E,		0x0145},
+	{HI846_REG_UNKNOWN_0954,		0x0089},
+	{HI846_REG_UNKNOWN_0956,		0x0000},
+	{HI846_REG_UNKNOWN_0958,		0xca80},
+	{HI846_REG_UNKNOWN_095A,		0x9240},
+	{HI846_REG_PLL_CFG_MIPI2_H,		0x4124},
+	{HI846_REG_TG_ENABLE,			0x0100},
+};
+
+static const struct hi846_reg mode_1280x720_mipi_4lane[] = {
+	/* 360Mbps */
+	{HI846_REG_UNKNOWN_0900,		0x0300},
+	{HI846_REG_MIPI_TX_OP_MODE,		0xc319},
+	{HI846_REG_UNKNOWN_0914,		0xc105},
+	{HI846_REG_TCLK_PREPARE,		0x030c},
+	{HI846_REG_UNKNOWN_0918,		0x0304},
+	{HI846_REG_THS_ZERO,			0x0708},
+	{HI846_REG_TCLK_POST,			0x0b04},
+	{HI846_REG_UNKNOWN_091E,		0x0500},
+	{HI846_REG_UNKNOWN_090C,		0x0208},
+	{HI846_REG_UNKNOWN_090E,		0x008a},
+	{HI846_REG_UNKNOWN_0954,		0x0089},
+	{HI846_REG_UNKNOWN_0956,		0x0000},
+	{HI846_REG_UNKNOWN_0958,		0xca80},
+	{HI846_REG_UNKNOWN_095A,		0x9240},
+	{HI846_REG_PLL_CFG_MIPI2_H,		0x4924},
+	{HI846_REG_TG_ENABLE,			0x0100},
+};
+
+static const struct hi846_reg mode_1632x1224_config[] = {
+	{HI846_REG_MODE_SELECT,			0x0000},
+	{HI846_REG_Y_ODD_INC_FOBP,		0x3311},
+	{HI846_REG_Y_ODD_INC_VACT,		0x3311},
+	{HI846_REG_Y_ADDR_START_VACT_H,		0x0040},
+	{HI846_REG_Y_ADDR_END_VACT_H,		0x09cf},
+	{HI846_REG_UNKNOWN_005C,		0x4202},
+	{HI846_REG_FLL,				0x09de},
+	{HI846_REG_LLP,				0x0ed8},
+	{HI846_REG_BINNING_MODE,		0x0122},
+	{HI846_REG_HBIN_MODE,			0x0100},
+	{HI846_REG_UNKNOWN_0A24,		0x0000},
+	{HI846_REG_X_START_H,			0x0000},
+	{HI846_REG_X_OUTPUT_SIZE_H,		0x0660},
+	{HI846_REG_Y_OUTPUT_SIZE_H,		0x04c8},
+	{HI846_REG_EXPOSURE,			0x09d8},
+	{HI846_REG_ISP_EN_H,			0x017a},
+
+	/* For OTP */
+	{HI846_REG_UNKNOWN_021C,		0x0003},
+	{HI846_REG_UNKNOWN_021E,		0x0235},
+
+	{HI846_REG_UNKNOWN_0418,		0x0000},
+	{HI846_REG_UNKNOWN_0B02,		0xe04d},
+	{HI846_REG_UNKNOWN_0B10,		0x6c21},
+	{HI846_REG_UNKNOWN_0B12,		0x0120},
+	{HI846_REG_UNKNOWN_0B14,		0x0005},
+	{HI846_REG_UNKNOWN_2008,		0x38fd},
+	{HI846_REG_UNKNOWN_326E,		0x0000},
+};
+
+static const struct hi846_reg mode_1632x1224_mipi_2lane[] = {
+	{HI846_REG_UNKNOWN_0900,		0x0300},
+	{HI846_REG_MIPI_TX_OP_MODE,		0x4319},
+	{HI846_REG_UNKNOWN_0914,		0xc109},
+	{HI846_REG_TCLK_PREPARE,		0x061a},
+	{HI846_REG_UNKNOWN_0918,		0x0407},
+	{HI846_REG_THS_ZERO,			0x0a0b},
+	{HI846_REG_TCLK_POST,			0x0e08},
+	{HI846_REG_UNKNOWN_091E,		0x0a00},
+	{HI846_REG_UNKNOWN_090C,		0x0427},
+	{HI846_REG_UNKNOWN_090E,		0x0069},
+	{HI846_REG_UNKNOWN_0954,		0x0089},
+	{HI846_REG_UNKNOWN_0956,		0x0000},
+	{HI846_REG_UNKNOWN_0958,		0xca80},
+	{HI846_REG_UNKNOWN_095A,		0x9240},
+	{HI846_REG_PLL_CFG_MIPI2_H,		0x4124},
+	{HI846_REG_TG_ENABLE,			0x0100},
+};
+
+static const struct hi846_reg mode_1632x1224_mipi_4lane[] = {
+	{HI846_REG_UNKNOWN_0900,		0x0300},
+	{HI846_REG_MIPI_TX_OP_MODE,		0xc319},
+	{HI846_REG_UNKNOWN_0914,		0xc105},
+	{HI846_REG_TCLK_PREPARE,		0x030c},
+	{HI846_REG_UNKNOWN_0918,		0x0304},
+	{HI846_REG_THS_ZERO,			0x0708},
+	{HI846_REG_TCLK_POST,			0x0b04},
+	{HI846_REG_UNKNOWN_091E,		0x0500},
+	{HI846_REG_UNKNOWN_090C,		0x0208},
+	{HI846_REG_UNKNOWN_090E,		0x001c},
+	{HI846_REG_UNKNOWN_0954,		0x0089},
+	{HI846_REG_UNKNOWN_0956,		0x0000},
+	{HI846_REG_UNKNOWN_0958,		0xca80},
+	{HI846_REG_UNKNOWN_095A,		0x9240},
+	{HI846_REG_PLL_CFG_MIPI2_H,		0x4924},
+	{HI846_REG_TG_ENABLE,			0x0100},
+};
+
+static const char * const hi846_test_pattern_menu[] = {
+	"Disabled",
+	"Solid Colour",
+	"100% Colour Bars",
+	"Fade To Grey Colour Bars",
+	"PN9",
+	"Gradient Horizontal",
+	"Gradient Vertical",
+	"Check Board",
+	"Slant Pattern",
+	"Resolution Pattern",
+};
+
+#define FREQ_INDEX_640	0
+#define FREQ_INDEX_1280	1
+static const s64 hi846_link_freqs[] = {
+	[FREQ_INDEX_640] = 80000000,
+	[FREQ_INDEX_1280] = 200000000,
+};
+
+static const struct hi846_reg_list hi846_init_regs_list_2lane = {
+	.num_of_regs = ARRAY_SIZE(hi846_init_2lane),
+	.regs = hi846_init_2lane,
+};
+
+static const struct hi846_reg_list hi846_init_regs_list_4lane = {
+	.num_of_regs = ARRAY_SIZE(hi846_init_4lane),
+	.regs = hi846_init_4lane,
+};
+
+static const struct hi846_mode supported_modes[] = {
+	{
+		.width = 640,
+		.height = 480,
+		.link_freq_index = FREQ_INDEX_640,
+		.fps = 120,
+		.frame_len = 631,
+		.llp = HI846_LINE_LENGTH,
+		.reg_list_config = {
+			.num_of_regs = ARRAY_SIZE(mode_640x480_config),
+			.regs = mode_640x480_config,
+		},
+		.reg_list_2lane = {
+			.num_of_regs = ARRAY_SIZE(mode_640x480_mipi_2lane),
+			.regs = mode_640x480_mipi_2lane,
+		},
+		.crop = {
+			.left = 0x58,
+			.top = 0x148,
+			.width = 640 * 4,
+			.height = 480 * 4,
+		},
+	},
+	{
+		.width = 1280,
+		.height = 720,
+		.link_freq_index = FREQ_INDEX_1280,
+		.fps = 90,
+		.frame_len = 842,
+		.llp = HI846_LINE_LENGTH,
+		.reg_list_config = {
+			.num_of_regs = ARRAY_SIZE(mode_1280x720_config),
+			.regs = mode_1280x720_config,
+		},
+		.reg_list_2lane = {
+			.num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_2lane),
+			.regs = mode_1280x720_mipi_2lane,
+		},
+		.reg_list_4lane = {
+			.num_of_regs = ARRAY_SIZE(mode_1280x720_mipi_4lane),
+			.regs = mode_1280x720_mipi_4lane,
+		},
+		.crop = {
+			.left = 0xb0,
+			.top = 0x238,
+			.width = 1280 * 2,
+			.height = 720 * 2,
+		},
+	},
+	{
+		.width = 1632,
+		.height = 1224,
+		.link_freq_index = FREQ_INDEX_1280,
+		.fps = 30,
+		.frame_len = 2526,
+		.llp = HI846_LINE_LENGTH,
+		.reg_list_config = {
+			.num_of_regs = ARRAY_SIZE(mode_1632x1224_config),
+			.regs = mode_1632x1224_config,
+		},
+		.reg_list_2lane = {
+			.num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_2lane),
+			.regs = mode_1632x1224_mipi_2lane,
+		},
+		.reg_list_4lane = {
+			.num_of_regs = ARRAY_SIZE(mode_1632x1224_mipi_4lane),
+			.regs = mode_1632x1224_mipi_4lane,
+		},
+		.crop = {
+			.left = 0x0,
+			.top = 0x0,
+			.width = 1632 * 2,
+			.height = 1224 * 2,
+		},
+	}
+};
+
+struct hi846_datafmt {
+	u32 code;
+	enum v4l2_colorspace colorspace;
+};
+
+static const char * const hi846_supply_names[] = {
+	"vddi", /* Digital I/O (1.8V or 2.8V) */
+	"vdda", /* Analog (2.8V) */
+	"vddd", /* Digital Core (1.2V) */
+};
+
+#define HI846_NUM_SUPPLIES ARRAY_SIZE(hi846_supply_names)
+
+struct hi846 {
+	struct gpio_desc *rst_gpio;
+	struct gpio_desc *shutdown_gpio;
+	struct regulator_bulk_data supplies[HI846_NUM_SUPPLIES];
+	struct clk *clock;
+	const struct hi846_datafmt *fmt;
+	struct v4l2_subdev sd;
+	struct media_pad pad;
+	struct v4l2_ctrl_handler ctrl_handler;
+	u8 nr_lanes;
+
+	struct v4l2_ctrl *link_freq;
+	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *vblank;
+	struct v4l2_ctrl *hblank;
+	struct v4l2_ctrl *exposure;
+
+	struct mutex mutex; /* protect cur_mode, streaming and chip access */
+	const struct hi846_mode *cur_mode;
+	bool streaming;
+};
+
+static inline struct hi846 *to_hi846(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct hi846, sd);
+}
+
+static const struct hi846_datafmt hi846_colour_fmts[] = {
+	{ HI846_MEDIA_BUS_FORMAT, V4L2_COLORSPACE_RAW },
+};
+
+static const struct hi846_datafmt *hi846_find_datafmt(u32 code)
+{
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(hi846_colour_fmts); i++)
+		if (hi846_colour_fmts[i].code == code)
+			return &hi846_colour_fmts[i];
+
+	return NULL;
+}
+
+static inline u8 hi846_get_link_freq_index(struct hi846 *hi846)
+{
+	return hi846->cur_mode->link_freq_index;
+}
+
+static s64 hi846_get_link_freq(struct hi846 *hi846)
+{
+	u8 index = hi846_get_link_freq_index(hi846);
+
+	return hi846_link_freqs[index];
+}
+
+static u64 hi846_calc_pixel_rate(struct hi846 *hi846)
+{
+	s64 link_freq = hi846_get_link_freq(hi846);
+	u64 pixel_rate = link_freq * 2 * hi846->nr_lanes;
+
+	do_div(pixel_rate, HI846_RGB_DEPTH);
+
+	return pixel_rate;
+}
+
+static int hi846_read_reg(struct hi846 *hi846, u16 reg, u8 *val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	struct i2c_msg msgs[2];
+	u8 addr_buf[2];
+	u8 data_buf[1] = {0};
+	int ret;
+
+	put_unaligned_be16(reg, addr_buf);
+	msgs[0].addr = client->addr;
+	msgs[0].flags = 0;
+	msgs[0].len = sizeof(addr_buf);
+	msgs[0].buf = addr_buf;
+	msgs[1].addr = client->addr;
+	msgs[1].flags = I2C_M_RD;
+	msgs[1].len = 1;
+	msgs[1].buf = &data_buf[0];
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret != ARRAY_SIZE(msgs)) {
+		dev_err(&client->dev, "i2c read error: %d\n", ret);
+		return -EIO;
+	}
+
+	*val = data_buf[0];
+
+	return 0;
+}
+
+static int hi846_write_reg(struct hi846 *hi846, u16 reg, u8 val)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	u8 buf[3] = { reg >> 8, reg & 0xff, val };
+	struct i2c_msg msg[] = {
+		{ .addr = client->addr, .flags = 0,
+		  .len = ARRAY_SIZE(buf), .buf = buf },
+	};
+	int ret;
+
+	ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+	if (ret != ARRAY_SIZE(msg)) {
+		dev_err(&client->dev, "i2c write error\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static void hi846_write_reg_16(struct hi846 *hi846, u16 reg, u16 val, int *err)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	u8 buf[6];
+	int ret;
+
+	if (*err < 0)
+		return;
+
+	put_unaligned_be16(reg, buf);
+	put_unaligned_be32(val << 8 * 2, buf + 2);
+	ret = i2c_master_send(client, buf, 4);
+	if (ret != 4) {
+		dev_err(&client->dev, "i2c_master_send != 4: %d\n", ret);
+		*err = -EIO;
+	}
+}
+
+static int hi846_write_reg_list(struct hi846 *hi846,
+				const struct hi846_reg_list *r_list)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	unsigned int i;
+	int ret = 0;
+
+	for (i = 0; i < r_list->num_of_regs; i++) {
+		hi846_write_reg_16(hi846, r_list->regs[i].address,
+				   r_list->regs[i].val, &ret);
+		if (ret) {
+			dev_err_ratelimited(&client->dev,
+					    "failed to write reg 0x%4.4x. error = %d",
+					    r_list->regs[i].address, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int hi846_update_digital_gain(struct hi846 *hi846, u16 d_gain)
+{
+	int ret = 0;
+
+	hi846_write_reg_16(hi846, HI846_REG_MWB_GR_GAIN_H, d_gain, &ret);
+	hi846_write_reg_16(hi846, HI846_REG_MWB_GB_GAIN_H, d_gain, &ret);
+	hi846_write_reg_16(hi846, HI846_REG_MWB_R_GAIN_H, d_gain, &ret);
+	hi846_write_reg_16(hi846, HI846_REG_MWB_B_GAIN_H, d_gain, &ret);
+
+	return ret;
+}
+
+static int hi846_test_pattern(struct hi846 *hi846, u32 pattern)
+{
+	int ret;
+	u8 val;
+
+	if (pattern) {
+		ret = hi846_read_reg(hi846, HI846_REG_ISP, &val);
+		if (ret)
+			return ret;
+
+		ret = hi846_write_reg(hi846, HI846_REG_ISP,
+				      val | HI846_REG_ISP_TPG_EN);
+		if (ret)
+			return ret;
+	}
+
+	return hi846_write_reg(hi846, HI846_REG_TEST_PATTERN, pattern);
+}
+
+static int hi846_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+	struct hi846 *hi846 = container_of(ctrl->handler,
+					     struct hi846, ctrl_handler);
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	s64 exposure_max;
+	int ret = 0;
+	u32 shutter, frame_len;
+
+	/* Propagate change of current control to all related controls */
+	if (ctrl->id == V4L2_CID_VBLANK) {
+		/* Update max exposure while meeting expected vblanking */
+		exposure_max = hi846->cur_mode->height + ctrl->val -
+			       HI846_EXPOSURE_MAX_MARGIN;
+		__v4l2_ctrl_modify_range(hi846->exposure,
+					 hi846->exposure->minimum,
+					 exposure_max, hi846->exposure->step,
+					 exposure_max);
+	}
+
+	if (!pm_runtime_get_if_in_use(&client->dev))
+		return 0;
+
+	switch (ctrl->id) {
+	case V4L2_CID_ANALOGUE_GAIN:
+		ret = hi846_write_reg(hi846, HI846_REG_ANALOG_GAIN, ctrl->val);
+		break;
+
+	case V4L2_CID_DIGITAL_GAIN:
+		ret = hi846_update_digital_gain(hi846, ctrl->val);
+		break;
+
+	case V4L2_CID_EXPOSURE:
+		shutter = ctrl->val;
+		frame_len = hi846->cur_mode->frame_len;
+
+		if (shutter > frame_len - 6) { /* margin */
+			frame_len = shutter + 6;
+			if (frame_len > 0xffff) { /* max frame len */
+				frame_len = 0xffff;
+			}
+		}
+
+		if (shutter < 6)
+			shutter = 6;
+		if (shutter > (0xffff - 6))
+			shutter = 0xffff - 6;
+
+		hi846_write_reg_16(hi846, HI846_REG_FLL, frame_len, &ret);
+		hi846_write_reg_16(hi846, HI846_REG_EXPOSURE, shutter, &ret);
+		break;
+
+	case V4L2_CID_VBLANK:
+		/* Update FLL that meets expected vertical blanking */
+		hi846_write_reg_16(hi846, HI846_REG_FLL,
+				   hi846->cur_mode->height + ctrl->val, &ret);
+		break;
+	case V4L2_CID_TEST_PATTERN:
+		ret = hi846_test_pattern(hi846, ctrl->val);
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	pm_runtime_put(&client->dev);
+
+	return ret;
+}
+
+static const struct v4l2_ctrl_ops hi846_ctrl_ops = {
+	.s_ctrl = hi846_set_ctrl,
+};
+
+static int hi846_init_controls(struct hi846 *hi846)
+{
+	struct v4l2_ctrl_handler *ctrl_hdlr;
+	s64 exposure_max, h_blank;
+	int ret;
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+
+	ctrl_hdlr = &hi846->ctrl_handler;
+	ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8);
+	if (ret)
+		return ret;
+
+	ctrl_hdlr->lock = &hi846->mutex;
+
+	hi846->link_freq =
+		v4l2_ctrl_new_int_menu(ctrl_hdlr, &hi846_ctrl_ops,
+				       V4L2_CID_LINK_FREQ,
+				       ARRAY_SIZE(hi846_link_freqs) - 1,
+				       0, hi846_link_freqs);
+	if (hi846->link_freq)
+		hi846->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	hi846->pixel_rate =
+		v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+				  V4L2_CID_PIXEL_RATE, 0,
+				  hi846_calc_pixel_rate(hi846), 1,
+				  hi846_calc_pixel_rate(hi846));
+	hi846->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+					  V4L2_CID_VBLANK,
+					  hi846->cur_mode->frame_len -
+					  hi846->cur_mode->height,
+					  HI846_FLL_MAX -
+					  hi846->cur_mode->height, 1,
+					  hi846->cur_mode->frame_len -
+					  hi846->cur_mode->height);
+
+	h_blank = hi846->cur_mode->llp - hi846->cur_mode->width;
+
+	hi846->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+					  V4L2_CID_HBLANK, h_blank, h_blank, 1,
+					  h_blank);
+	if (hi846->hblank)
+		hi846->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+	v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+			  HI846_ANAL_GAIN_MIN, HI846_ANAL_GAIN_MAX,
+			  HI846_ANAL_GAIN_STEP, HI846_ANAL_GAIN_MIN);
+	v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+			  HI846_DGTL_GAIN_MIN, HI846_DGTL_GAIN_MAX,
+			  HI846_DGTL_GAIN_STEP, HI846_DGTL_GAIN_DEFAULT);
+	exposure_max = hi846->cur_mode->frame_len - HI846_EXPOSURE_MAX_MARGIN;
+	hi846->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &hi846_ctrl_ops,
+					    V4L2_CID_EXPOSURE,
+					    HI846_EXPOSURE_MIN, exposure_max,
+					    HI846_EXPOSURE_STEP,
+					    exposure_max);
+	v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &hi846_ctrl_ops,
+				     V4L2_CID_TEST_PATTERN,
+				     ARRAY_SIZE(hi846_test_pattern_menu) - 1,
+				     0, 0, hi846_test_pattern_menu);
+	if (ctrl_hdlr->error) {
+		dev_err(&client->dev, "v4l ctrl handler error: %d\n",
+			ctrl_hdlr->error);
+		return ctrl_hdlr->error;
+	}
+
+	hi846->sd.ctrl_handler = ctrl_hdlr;
+
+	return 0;
+}
+
+static int hi846_set_video_mode(struct hi846 *hi846, int fps)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	int frame_length;
+	int ret = 0;
+	int dummy_lines;
+	s64 link_freq = hi846_get_link_freq(hi846);
+
+	dev_dbg(&client->dev, "%s: link freq: %lld\n", __func__,
+		hi846_get_link_freq(hi846));
+
+	do_div(link_freq, fps);
+	frame_length = link_freq;
+	do_div(frame_length, HI846_LINE_LENGTH);
+
+	dummy_lines = (frame_length > hi846->cur_mode->frame_len) ?
+			(frame_length - hi846->cur_mode->frame_len) : 0;
+
+	frame_length = hi846->cur_mode->frame_len + dummy_lines;
+
+	dev_dbg(&client->dev, "%s: frame length calculated: %d\n", __func__,
+		frame_length);
+
+	hi846_write_reg_16(hi846, HI846_REG_FLL, frame_length & 0xFFFF, &ret);
+	hi846_write_reg_16(hi846, HI846_REG_LLP, HI846_LINE_LENGTH & 0xFFFF, &ret);
+
+	return ret;
+}
+
+static int hi846_start_streaming(struct hi846 *hi846)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	int ret = 0;
+	u8 val;
+
+	if (hi846->nr_lanes == 2)
+		ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_2lane);
+	else
+		ret = hi846_write_reg_list(hi846, &hi846_init_regs_list_4lane);
+	if (ret) {
+		dev_err(&client->dev, "failed to set plls: %d\n", ret);
+		return ret;
+	}
+
+	ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_config);
+	if (ret) {
+		dev_err(&client->dev, "failed to set mode: %d\n", ret);
+		return ret;
+	}
+
+	if (hi846->nr_lanes == 2) {
+		if (!&hi846->cur_mode->reg_list_2lane) {
+			dev_err(&client->dev, "2 lanes unsupported for this mode\n");
+			return -EINVAL;
+		}
+		ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_2lane);
+	} else {
+		if (!&hi846->cur_mode->reg_list_4lane) {
+			dev_err(&client->dev, "4 lanes unsupported for this mode\n");
+			return -EINVAL;
+		}
+		ret = hi846_write_reg_list(hi846, &hi846->cur_mode->reg_list_4lane);
+	}
+	if (ret) {
+		dev_err(&client->dev, "failed to set mipi mode: %d\n", ret);
+		return ret;
+	}
+
+	hi846_set_video_mode(hi846, hi846->cur_mode->fps);
+
+	ret = __v4l2_ctrl_handler_setup(hi846->sd.ctrl_handler);
+	if (ret)
+		return ret;
+
+	/*
+	 * Reading 0x0034 is purely done for debugging reasons: It is not
+	 * documented in the DS but only mentioned once:
+	 * "If 0x0034[2] bit is disabled , Visible pixel width and height is 0."
+	 * So even though that sounds like we won't see anything, we don't
+	 * know more about this, so in that case only inform the user but do
+	 * nothing more.
+	 */
+	ret = hi846_read_reg(hi846, 0x0034, &val);
+	if (ret)
+		return ret;
+	if (!(val & BIT(2)))
+		dev_info(&client->dev, "visible pixel width and height is 0\n");
+
+	ret = hi846_write_reg(hi846, HI846_REG_MODE_SELECT,
+			      HI846_MODE_STREAMING);
+	if (ret) {
+		dev_err(&client->dev, "failed to start stream");
+		return ret;
+	}
+
+	hi846->streaming = 1;
+
+	dev_dbg(&client->dev, "%s: started streaming successfully\n", __func__);
+
+	return ret;
+}
+
+static void hi846_stop_streaming(struct hi846 *hi846)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+
+	if (hi846_write_reg(hi846, HI846_REG_MODE_SELECT, HI846_MODE_STANDBY))
+		dev_err(&client->dev, "failed to stop stream");
+
+	hi846->streaming = 0;
+}
+
+static int hi846_set_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct hi846 *hi846 = to_hi846(sd);
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	int ret = 0;
+
+	if (hi846->streaming == enable)
+		return 0;
+
+	mutex_lock(&hi846->mutex);
+
+	if (enable) {
+		ret = pm_runtime_get_sync(&client->dev);
+		if (ret < 0) {
+			pm_runtime_put_noidle(&client->dev);
+			goto out;
+		}
+
+		ret = hi846_start_streaming(hi846);
+		if (ret) {
+			enable = 0;
+			hi846_stop_streaming(hi846);
+			pm_runtime_put(&client->dev);
+		}
+	} else {
+		hi846_stop_streaming(hi846);
+		pm_runtime_put(&client->dev);
+	}
+
+out:
+	mutex_unlock(&hi846->mutex);
+
+	return ret;
+}
+
+static int hi846_power_on(struct hi846 *hi846)
+{
+	int ret;
+
+	ret = regulator_bulk_enable(HI846_NUM_SUPPLIES, hi846->supplies);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_prepare_enable(hi846->clock);
+	if (ret < 0)
+		return ret;
+
+	if (hi846->shutdown_gpio)
+		gpiod_set_value_cansleep(hi846->shutdown_gpio, 0);
+
+	/* 30us = 2400 cycles at 80Mhz */
+	usleep_range(30, 60);
+	if (hi846->rst_gpio)
+		gpiod_set_value_cansleep(hi846->rst_gpio, 0);
+	usleep_range(30, 60);
+
+	return 0;
+}
+
+static void hi846_power_off(struct hi846 *hi846)
+{
+	if (hi846->rst_gpio)
+		gpiod_set_value_cansleep(hi846->rst_gpio, 1);
+
+	if (hi846->shutdown_gpio)
+		gpiod_set_value_cansleep(hi846->shutdown_gpio, 1);
+
+	clk_disable_unprepare(hi846->clock);
+	regulator_bulk_disable(HI846_NUM_SUPPLIES, hi846->supplies);
+}
+
+static int __maybe_unused hi846_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct hi846 *hi846 = to_hi846(sd);
+
+	if (hi846->streaming)
+		hi846_stop_streaming(hi846);
+
+	hi846_power_off(hi846);
+
+	return 0;
+}
+
+static int __maybe_unused hi846_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct hi846 *hi846 = to_hi846(sd);
+	int ret;
+
+	ret = hi846_power_on(hi846);
+	if (ret)
+		return ret;
+
+	if (hi846->streaming) {
+		ret = hi846_start_streaming(hi846);
+		if (ret) {
+			dev_err(dev, "%s: start streaming failed: %d\n",
+				__func__, ret);
+			goto error;
+		}
+	}
+
+	return 0;
+
+error:
+	hi846_power_off(hi846);
+	return ret;
+}
+
+static int hi846_set_format(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_pad_config *cfg,
+			    struct v4l2_subdev_format *format)
+{
+	struct hi846 *hi846 = to_hi846(sd);
+	struct v4l2_mbus_framefmt *mf = &format->format;
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	const struct hi846_datafmt *fmt = hi846_find_datafmt(mf->code);
+	u32 tgt_fps;
+	s32 vblank_def, h_blank;
+
+	if (!fmt) {
+		mf->code = hi846_colour_fmts[0].code;
+		mf->colorspace = hi846_colour_fmts[0].colorspace;
+		fmt = &hi846_colour_fmts[0];
+	}
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+		*v4l2_subdev_get_try_format(sd, cfg, format->pad) = *mf;
+		return 0;
+	}
+
+	mutex_lock(&hi846->mutex);
+
+	if (hi846->streaming) {
+		mutex_unlock(&hi846->mutex);
+		return -EBUSY;
+	}
+
+	hi846->fmt = fmt;
+
+	hi846->cur_mode =
+		v4l2_find_nearest_size(supported_modes,
+				       ARRAY_SIZE(supported_modes),
+				       width, height, mf->width, mf->height);
+	dev_dbg(&client->dev, "%s: found mode: %dx%d\n", __func__,
+		hi846->cur_mode->width, hi846->cur_mode->height);
+
+	tgt_fps = hi846->cur_mode->fps;
+	dev_dbg(&client->dev, "%s: target fps: %d\n", __func__, tgt_fps);
+
+	mf->width = hi846->cur_mode->width;
+	mf->height = hi846->cur_mode->height;
+	mf->code = HI846_MEDIA_BUS_FORMAT;
+	mf->field = V4L2_FIELD_NONE;
+
+	__v4l2_ctrl_s_ctrl(hi846->link_freq, hi846_get_link_freq_index(hi846));
+	__v4l2_ctrl_s_ctrl_int64(hi846->pixel_rate,
+				 hi846_calc_pixel_rate(hi846));
+
+	/* Update limits and set FPS to default */
+	vblank_def = hi846->cur_mode->frame_len - hi846->cur_mode->height;
+	__v4l2_ctrl_modify_range(hi846->vblank,
+				 hi846->cur_mode->frame_len - hi846->cur_mode->height,
+				 HI846_FLL_MAX - hi846->cur_mode->height, 1,
+				 vblank_def);
+	__v4l2_ctrl_s_ctrl(hi846->vblank, vblank_def);
+
+	h_blank = hi846->cur_mode->llp - hi846->cur_mode->width;
+
+	__v4l2_ctrl_modify_range(hi846->hblank, h_blank, h_blank, 1,
+				 h_blank);
+
+	dev_dbg(&client->dev, "Set fmt w=%d h=%d code=0x%x colorspace=0x%x\n",
+		mf->width, mf->height,
+		fmt->code, fmt->colorspace);
+
+	mutex_unlock(&hi846->mutex);
+
+	return 0;
+}
+
+static int hi846_get_format(struct v4l2_subdev *sd,
+			    struct v4l2_subdev_pad_config *cfg,
+			    struct v4l2_subdev_format *format)
+{
+	struct hi846 *hi846 = to_hi846(sd);
+	struct v4l2_mbus_framefmt *mf = &format->format;
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+	if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+		format->format = *v4l2_subdev_get_try_format(&hi846->sd,
+							cfg,
+							format->pad);
+		return 0;
+	}
+
+	mutex_lock(&hi846->mutex);
+	mf->code        = HI846_MEDIA_BUS_FORMAT;
+	mf->colorspace  = V4L2_COLORSPACE_RAW;
+	mf->field       = V4L2_FIELD_NONE;
+	mf->width       = hi846->cur_mode->width;
+	mf->height      = hi846->cur_mode->height;
+	mutex_unlock(&hi846->mutex);
+	dev_dbg(&client->dev,
+		"Get format w=%d h=%d code=0x%x colorspace=0x%x\n",
+		mf->width, mf->height, mf->code, mf->colorspace);
+
+	return 0;
+}
+
+static int hi846_enum_mbus_code(struct v4l2_subdev *sd,
+				struct v4l2_subdev_pad_config *cfg,
+				struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad || code->index > 0)
+		return -EINVAL;
+
+	code->code = HI846_MEDIA_BUS_FORMAT;
+
+	return 0;
+}
+
+static int hi846_enum_frame_size(struct v4l2_subdev *sd,
+				 struct v4l2_subdev_pad_config *cfg,
+				 struct v4l2_subdev_frame_size_enum *fse)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+	if (fse->pad || fse->index >= ARRAY_SIZE(supported_modes))
+		return -EINVAL;
+
+	if (fse->code != HI846_MEDIA_BUS_FORMAT) {
+		dev_err(&client->dev, "frame size enum not matching\n");
+		return -EINVAL;
+	}
+
+	fse->min_width = supported_modes[fse->index].width;
+	fse->max_width = supported_modes[fse->index].width;
+	fse->min_height = supported_modes[fse->index].height;
+	fse->max_height = supported_modes[fse->index].height;
+
+	dev_dbg(&client->dev, "%s: max width: %d max height: %d\n", __func__,
+		fse->max_width, fse->max_height);
+
+	return 0;
+}
+
+static int hi846_get_selection(struct v4l2_subdev *sd,
+			       struct v4l2_subdev_pad_config *cfg,
+			       struct v4l2_subdev_selection *sel)
+{
+	struct hi846 *hi846 = to_hi846(sd);
+
+	switch (sel->target) {
+	case V4L2_SEL_TGT_CROP:
+		mutex_lock(&hi846->mutex);
+		switch (sel->which) {
+		case V4L2_SUBDEV_FORMAT_TRY:
+			v4l2_subdev_get_try_crop(sd, cfg, sel->pad);
+			break;
+		case V4L2_SUBDEV_FORMAT_ACTIVE:
+			sel->r = hi846->cur_mode->crop;
+			break;
+		}
+		mutex_unlock(&hi846->mutex);
+		return 0;
+	case V4L2_SEL_TGT_CROP_BOUNDS:
+	case V4L2_SEL_TGT_CROP_DEFAULT:
+		sel->r.top = 0;
+		sel->r.left = 0;
+		sel->r.width = 3264;
+		sel->r.height = 2448;
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int hi846_init_cfg(struct v4l2_subdev *sd, struct v4l2_subdev_pad_config *cfg)
+{
+	struct hi846 *hi846 = to_hi846(sd);
+	struct v4l2_mbus_framefmt *mf;
+
+	mf = v4l2_subdev_get_try_format(sd, cfg, 0);
+
+	mutex_lock(&hi846->mutex);
+	mf->code        = HI846_MEDIA_BUS_FORMAT;
+	mf->colorspace  = V4L2_COLORSPACE_RAW;
+	mf->field       = V4L2_FIELD_NONE;
+	mf->width       = hi846->cur_mode->width;
+	mf->height      = hi846->cur_mode->height;
+	mutex_unlock(&hi846->mutex);
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops hi846_video_ops = {
+	.s_stream = hi846_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops hi846_pad_ops = {
+	.init_cfg = hi846_init_cfg,
+	.enum_frame_size = hi846_enum_frame_size,
+	.enum_mbus_code = hi846_enum_mbus_code,
+	.set_fmt = hi846_set_format,
+	.get_fmt = hi846_get_format,
+	.get_selection = hi846_get_selection,
+};
+
+static const struct v4l2_subdev_ops hi846_subdev_ops = {
+	.video = &hi846_video_ops,
+	.pad = &hi846_pad_ops,
+};
+
+static const struct media_entity_operations hi846_subdev_entity_ops = {
+	.link_validate = v4l2_subdev_link_validate,
+};
+
+static int hi846_identify_module(struct hi846 *hi846)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&hi846->sd);
+	int ret;
+	u8 hi, lo;
+
+	ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_L, &lo);
+	if (ret)
+		return ret;
+
+	if (lo != HI846_CHIP_ID_L) {
+		dev_err(&client->dev, "wrong chip id low byte: %x", lo);
+		return -ENXIO;
+	}
+
+	ret = hi846_read_reg(hi846, HI846_REG_CHIP_ID_H, &hi);
+	if (ret)
+		return ret;
+
+	if (hi != HI846_CHIP_ID_H) {
+		dev_err(&client->dev, "wrong chip id high byte: %x", hi);
+		return -ENXIO;
+	}
+
+	dev_info(&client->dev, "chip id %02X %02X using %d mipi lanes\n", hi, lo,
+		 hi846->nr_lanes);
+
+	return 0;
+}
+
+static int hi846_parse_dt(struct hi846 *hi846, struct device *dev)
+{
+	struct fwnode_handle *ep;
+	struct fwnode_handle *fwnode = dev_fwnode(dev);
+	struct v4l2_fwnode_endpoint bus_cfg = {
+		.bus_type = V4L2_MBUS_CSI2_DPHY
+	};
+	int ret;
+
+	ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+	if (!ep) {
+		dev_err(dev, "unable to find endpoint node\n");
+		return -ENXIO;
+	}
+
+	ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
+	fwnode_handle_put(ep);
+	if (ret) {
+		dev_err(dev, "failed to parse endpoint node: %d\n", ret);
+		return ret;
+	}
+
+	if (bus_cfg.bus.mipi_csi2.num_data_lanes != 2 &&
+	    bus_cfg.bus.mipi_csi2.num_data_lanes != 4) {
+		dev_err(dev, "number of CSI2 data lanes %d is not supported",
+			bus_cfg.bus.mipi_csi2.num_data_lanes);
+		v4l2_fwnode_endpoint_free(&bus_cfg);
+		return -EINVAL;
+	}
+
+	hi846->nr_lanes = bus_cfg.bus.mipi_csi2.num_data_lanes;
+	v4l2_fwnode_endpoint_free(&bus_cfg);
+
+	hi846->rst_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(hi846->rst_gpio)) {
+		dev_err(dev, "failed to get reset gpio: %pe\n", hi846->rst_gpio);
+		return PTR_ERR(hi846->rst_gpio);
+	}
+
+	hi846->shutdown_gpio = devm_gpiod_get_optional(dev, "shutdown", GPIOD_OUT_LOW);
+	if (IS_ERR(hi846->shutdown_gpio)) {
+		dev_err(dev, "failed to get shutdown gpio: %pe\n", hi846->shutdown_gpio);
+		return PTR_ERR(hi846->shutdown_gpio);
+	}
+
+	return 0;
+}
+
+static int hi846_probe(struct i2c_client *client)
+{
+	struct hi846 *hi846;
+	int ret;
+	int i;
+	u32 mclk_freq;
+
+	hi846 = devm_kzalloc(&client->dev, sizeof(*hi846), GFP_KERNEL);
+	if (!hi846)
+		return -ENOMEM;
+
+	ret = hi846_parse_dt(hi846, &client->dev);
+	if (ret) {
+		dev_err(&client->dev, "failed to check HW configuration: %d", ret);
+		return ret;
+	}
+
+	hi846->clock = devm_clk_get(&client->dev, NULL);
+	if (IS_ERR(hi846->clock)) {
+		dev_err(&client->dev, "failed to get clock: %pe\n", hi846->clock);
+		return PTR_ERR(hi846->clock);
+	}
+
+	mclk_freq = clk_get_rate(hi846->clock);
+	dev_dbg(&client->dev, "clk rate: %u\n", mclk_freq);
+
+	for (i = 0; i < HI846_NUM_SUPPLIES; i++)
+		hi846->supplies[i].supply = hi846_supply_names[i];
+
+	ret = devm_regulator_bulk_get(&client->dev, HI846_NUM_SUPPLIES,
+				      hi846->supplies);
+	if (ret < 0)
+		return ret;
+
+	mutex_init(&hi846->mutex);
+
+	hi846->cur_mode = &supported_modes[0];
+	ret = hi846_init_controls(hi846);
+	if (ret) {
+		dev_err(&client->dev, "failed to init controls: %d", ret);
+		return ret;
+	}
+
+	v4l2_i2c_subdev_init(&hi846->sd, client, &hi846_subdev_ops);
+	hi846->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+	hi846->sd.entity.ops = &hi846_subdev_entity_ops;
+	hi846->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+	hi846->pad.flags = MEDIA_PAD_FL_SOURCE;
+	ret = media_entity_pads_init(&hi846->sd.entity, 1, &hi846->pad);
+	if (ret) {
+		dev_err(&client->dev, "failed to init entity pads: %d", ret);
+		goto probe_error_v4l2_ctrl_handler_free;
+	}
+
+	ret = hi846_power_on(hi846);
+	if (ret)
+		goto probe_error_media_entity_cleanup;
+
+	ret = hi846_identify_module(hi846);
+	if (ret)
+		goto probe_error_media_entity_cleanup;
+
+	ret = v4l2_async_register_subdev_sensor(&hi846->sd);
+	if (ret < 0) {
+		dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+			ret);
+		goto probe_error_media_entity_cleanup;
+	}
+
+	pm_runtime_set_active(&client->dev);
+	pm_runtime_enable(&client->dev);
+	pm_runtime_idle(&client->dev);
+
+	return 0;
+
+probe_error_media_entity_cleanup:
+	hi846_power_off(hi846);
+	media_entity_cleanup(&hi846->sd.entity);
+
+probe_error_v4l2_ctrl_handler_free:
+	v4l2_ctrl_handler_free(hi846->sd.ctrl_handler);
+	mutex_destroy(&hi846->mutex);
+
+	return ret;
+}
+
+static int hi846_remove(struct i2c_client *client)
+{
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct hi846 *hi846 = to_hi846(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	media_entity_cleanup(&sd->entity);
+	v4l2_ctrl_handler_free(sd->ctrl_handler);
+
+	pm_runtime_disable(&client->dev);
+	if (!pm_runtime_status_suspended(&client->dev))
+		hi846_suspend(&client->dev);
+	pm_runtime_set_suspended(&client->dev);
+
+	mutex_destroy(&hi846->mutex);
+
+	return 0;
+}
+
+static UNIVERSAL_DEV_PM_OPS(hi846_pm_ops, hi846_suspend, hi846_resume, NULL);
+
+static const struct of_device_id hi846_of_match[] = {
+	{ .compatible = "hynix,hi846", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, hi846_of_match);
+
+static struct i2c_driver hi846_i2c_driver = {
+	.driver = {
+		.name = "hi846",
+		.pm = &hi846_pm_ops,
+		.of_match_table = of_match_ptr(hi846_of_match),
+	},
+	.probe_new = hi846_probe,
+	.remove = hi846_remove,
+};
+
+module_i2c_driver(hi846_i2c_driver);
+
+MODULE_AUTHOR("Angus Ainslie <angus@akkea.ca>");
+MODULE_AUTHOR("Martin Kepplinger <martin.kepplinger@puri.sm>");
+MODULE_DESCRIPTION("Hynix HI846 sensor driver");
+MODULE_LICENSE("GPL v2");
-- 
2.30.2

[PATCH v4 4/5] arm64: defconfig: enable VIDEO_HI846

[Martin Kepplinger]

build the driver for the Hi-846 camera by default on arm64, where it's
going to be used on at least the imx8mq-librem5 board.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 1f1cb5b0dfe0..3a838464d3c1 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -665,6 +665,7 @@ CONFIG_VIDEO_RENESAS_FCP=m
 CONFIG_VIDEO_RENESAS_VSP1=m
 CONFIG_SDR_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_RCAR_DRIF=m
+CONFIG_VIDEO_HI846=m
 CONFIG_VIDEO_IMX219=m
 CONFIG_VIDEO_OV5645=m
 CONFIG_VIDEO_QCOM_CAMSS=m
-- 
2.30.2

[PATCH v4 5/5] Documentation: i2c-cardlist: add the Hynix hi846 sensor

[Martin Kepplinger]

Add the SK Hynix Hi-846 8M Pixel CMOS image sensor to the i2c-cardlist.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
---
 Documentation/admin-guide/media/i2c-cardlist.rst | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/admin-guide/media/i2c-cardlist.rst b/Documentation/admin-guide/media/i2c-cardlist.rst
index e60d459d18a9..185e07a3da43 100644
--- a/Documentation/admin-guide/media/i2c-cardlist.rst
+++ b/Documentation/admin-guide/media/i2c-cardlist.rst
@@ -60,6 +60,7 @@ Driver        Name
 ============  ==========================================================
 et8ek8        ET8EK8 camera sensor
 hi556         Hynix Hi-556 sensor
+hi846         Hynix Hi-846 sensor
 imx214        Sony IMX214 sensor
 imx219        Sony IMX219 sensor
 imx258        Sony IMX258 sensor
-- 
2.30.2

Re: [PATCH v4 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor

[Laurent Pinchart]

Hi Martin

Thank you for the patch.

On Mon, Jun 07, 2021 at 12:52:10PM +0200, Martin Kepplinger wrote:
> Document the bindings used for the SK Hynix Hi-846 CMOS camera driver.
> 
> Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
> ---
>  .../bindings/media/i2c/hynix,hi846.yaml       | 105 ++++++++++++++++++
>  1 file changed, 105 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> new file mode 100644
> index 000000000000..19825392fb1f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> @@ -0,0 +1,105 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> +
> +maintainers:
> +  - Martin Kepplinger <martin.kepplinger@puri.sm>
> +
> +description: |-
> +  The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> +  interface and CCI (I2C compatible) control bus. The output format
> +  is raw Bayer.
> +
> +properties:
> +  compatible:
> +    const: hynix,hi846
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: Reference to the mclk clock.
> +
> +  reset-gpios:
> +    description: Reference to the GPIO connected to the RESETB pin. Active low.
> +    maxItems: 1
> +
> +  shutdown-gpios:
> +    description: Reference to the GPIO connected to the XSHUTDOWN pin. Active low.
> +    maxItems: 1
> +
> +  vddi-supply:

I think it's called vddio (seems to be a typo on page 8).

> +    description: Definition of the regulator used for the 1.8V or 2.8V I/O power supply.

You could just say "... for the VDDIO supply". Same below. Up to you.

With the name fixed and the description optionally updated,

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Please add my tag if you post a new version.

> +
> +  vdda-supply:
> +    description: Definition of the regulator used for the 2.8V analog power supply.
> +
> +  vddd-supply:
> +    description: Definition of the regulator used for the 1.2V core power supply.
> +
> +  port:
> +    $ref: /schemas/graph.yaml#/properties/port
> +
> +    properties:
> +      endpoint:
> +        $ref: /schemas/media/video-interfaces.yaml#
> +        unevaluatedProperties: false
> +
> +        properties:
> +          data-lanes:
> +            oneOf:
> +              - items:
> +                  - const: 1
> +                  - const: 2
> +                  - const: 3
> +                  - const: 4
> +              - items:
> +                  - const: 1
> +                  - const: 2
> +
> +        required:
> +          - data-lanes
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - vddi-supply
> +  - vdda-supply
> +  - vddd-supply
> +  - port
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        hi846: camera@20 {
> +            compatible = "hynix,hi846";
> +            reg = <0x20>;
> +            clocks = <&clk>;
> +            vddi-supply = <&reg_camera_pwr_en>;
> +            vdda-supply = <&reg_camera_pwr_en>;
> +            vddd-supply = <&reg_camera_pwr_en>;
> +            reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> +
> +            port {
> +                camera_out: endpoint {
> +                    remote-endpoint = <&csi1_ep1>;
> +                    data-lanes = <1 2>;
> +                };
> +            };
> +        };
> +    };
> +
> +...

-- 
Regards,

Laurent Pinchart

Re: [PATCH v4 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor

[Martin Kepplinger]

Am Dienstag, dem 08.06.2021 um 00:15 +0300 schrieb Laurent Pinchart:
> Hi Martin
> 
> Thank you for the patch.
> 
> On Mon, Jun 07, 2021 at 12:52:10PM +0200, Martin Kepplinger wrote:
> > Document the bindings used for the SK Hynix Hi-846 CMOS camera
> > driver.
> > 
> > Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
> > ---
> >  .../bindings/media/i2c/hynix,hi846.yaml       | 105
> > ++++++++++++++++++
> >  1 file changed, 105 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > 
> > diff --git
> > a/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > new file mode 100644
> > index 000000000000..19825392fb1f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> > @@ -0,0 +1,105 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/hynix,hi846.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: SK Hynix Hi-846 1/4" 8M Pixel MIPI CSI-2 sensor
> > +
> > +maintainers:
> > +  - Martin Kepplinger <martin.kepplinger@puri.sm>
> > +
> > +description: |-
> > +  The Hi-846 is a raw image sensor with an MIPI CSI-2 image data
> > +  interface and CCI (I2C compatible) control bus. The output
> > format
> > +  is raw Bayer.
> > +
> > +properties:
> > +  compatible:
> > +    const: hynix,hi846
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  clocks:
> > +    items:
> > +      - description: Reference to the mclk clock.
> > +
> > +  reset-gpios:
> > +    description: Reference to the GPIO connected to the RESETB
> > pin. Active low.
> > +    maxItems: 1
> > +
> > +  shutdown-gpios:
> > +    description: Reference to the GPIO connected to the XSHUTDOWN
> > pin. Active low.
> > +    maxItems: 1
> > +
> > +  vddi-supply:
> 
> I think it's called vddio (seems to be a typo on page 8).
> 
> > +    description: Definition of the regulator used for the 1.8V or
> > 2.8V I/O power supply.
> 
> You could just say "... for the VDDIO supply". Same below. Up to you.
> 
> With the name fixed and the description optionally updated,
> 
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> Please add my tag if you post a new version.

I'll rename the binding and add the tag. I haven't added your previous
tag because you found improvements based on the DS afterwards.

thanks again!
                              martin

Re: [PATCH v4 2/5] dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor

[Rob Herring]

On Mon, 07 Jun 2021 12:52:10 +0200, Martin Kepplinger wrote:
> Document the bindings used for the SK Hynix Hi-846 CMOS camera driver.
> 
> Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
> ---
>  .../bindings/media/i2c/hynix,hi846.yaml       | 105 ++++++++++++++++++
>  1 file changed, 105 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/hynix,hi846.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>