From: Jacopo Mondi <jacopo@jmondi.org>
To: "Krzysztof Hałasa" <khalasa@piap.pl>,
"Mauro Carvalho Chehab" <mchehab@kernel.org>,
"Sakari Ailus" <sakari.ailus@iki.fi>,
"Laurent Pinchart" <laurent.pinchart@ideasonboard.com>
Cc: Jacopo Mondi <jacopo@jmondi.org>, linux-media@vger.kernel.org
Subject: [PATCH 09/10] media: ar0521: Rework startup sequence
Date: Wed, 5 Oct 2022 21:06:12 +0200 [thread overview]
Message-ID: <20221005190613.394277-10-jacopo@jmondi.org> (raw)
In-Reply-To: <20221005190613.394277-1-jacopo@jmondi.org>
The ar0521_write_mode() function explicitly programs the exposure time
register and the test pattern register, which are now setup by the call
to __v4l2_ctrl_handler_setup() in ar0521_set_stream().
Removing those register writes from ar0521_write_mode() reduces the
function to two operations: geometry configuration and pll
configuration.
Move those operations in the ar0521_set_stream() caller and remove
ar0521_write_mode(). However maintain the ar0521_calc_pll() function
separated as it is used during pad format configuration to update the
PIXEL_RATE control value.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
---
drivers/media/i2c/ar0521.c | 50 ++++++++++++--------------------------
1 file changed, 16 insertions(+), 34 deletions(-)
diff --git a/drivers/media/i2c/ar0521.c b/drivers/media/i2c/ar0521.c
index d46a51332964..670fa33acc6f 100644
--- a/drivers/media/i2c/ar0521.c
+++ b/drivers/media/i2c/ar0521.c
@@ -329,7 +329,7 @@ static u32 calc_pll(struct ar0521_dev *sensor, u32 freq, u16 *pre_ptr, u16 *mult
return pll;
}
-static void ar0521_calc_mode(struct ar0521_dev *sensor)
+static void ar0521_calc_pll(struct ar0521_dev *sensor)
{
unsigned int pixel_clock;
unsigned int link_freq;
@@ -403,7 +403,7 @@ static void ar0521_calc_mode(struct ar0521_dev *sensor)
sensor->pll.mult = sensor->pll.mult2 = mult;
}
-static int ar0521_write_mode(struct ar0521_dev *sensor)
+static int ar0521_pll_config(struct ar0521_dev *sensor)
{
__be16 pll_regs[] = {
be(AR0521_REG_VT_PIX_CLK_DIV),
@@ -414,36 +414,9 @@ static int ar0521_write_mode(struct ar0521_dev *sensor)
/* 0x308 */ be(sensor->pll.vt_pix * 2), /* op_pix_clk_div = 2 * vt_pix_clk_div */
/* 0x30A */ be(1) /* op_sys_clk_div */
};
- int ret;
-
- /* Stop streaming for just a moment */
- ret = ar0521_write_reg(sensor, AR0521_REG_RESET,
- AR0521_REG_RESET_DEFAULTS);
- if (ret)
- return ret;
-
- ret = ar0521_set_geometry(sensor);
- if (ret)
- return ret;
-
- ret = ar0521_write_regs(sensor, pll_regs, ARRAY_SIZE(pll_regs));
- if (ret)
- return ret;
-
- ret = ar0521_write_reg(sensor, AR0521_REG_COARSE_INTEGRATION_TIME,
- sensor->ctrls.exposure->val);
- if (ret)
- return ret;
-
- ret = ar0521_write_reg(sensor, AR0521_REG_RESET,
- AR0521_REG_RESET_DEFAULTS |
- AR0521_REG_RESET_STREAM);
- if (ret)
- return ret;
- ret = ar0521_write_reg(sensor, AR0521_REG_TEST_PATTERN_MODE,
- sensor->ctrls.test_pattern->val);
- return ret;
+ ar0521_calc_pll(sensor);
+ return ar0521_write_regs(sensor, pll_regs, ARRAY_SIZE(pll_regs));
}
static int ar0521_set_stream(struct ar0521_dev *sensor, bool on)
@@ -455,8 +428,17 @@ static int ar0521_set_stream(struct ar0521_dev *sensor, bool on)
if (ret < 0)
return ret;
- ar0521_calc_mode(sensor);
- ret = ar0521_write_mode(sensor);
+ /* Stop streaming for just a moment */
+ ret = ar0521_write_reg(sensor, AR0521_REG_RESET,
+ AR0521_REG_RESET_DEFAULTS);
+ if (ret)
+ return ret;
+
+ ret = ar0521_set_geometry(sensor);
+ if (ret)
+ return ret;
+
+ ret = ar0521_pll_config(sensor);
if (ret)
goto err;
@@ -562,7 +544,7 @@ static int ar0521_set_fmt(struct v4l2_subdev *sd,
}
sensor->fmt = format->format;
- ar0521_calc_mode(sensor);
+ ar0521_calc_pll(sensor);
/*
* Update the exposure and blankings limits. Blankings are also reset
--
2.37.3
next prev parent reply other threads:[~2022-10-05 19:07 UTC|newest]
Thread overview: 71+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-05 19:06 [PATCH 00/10] media: ar0521: Add analog gain, rework clock tree Jacopo Mondi
2022-10-05 19:06 ` [PATCH 01/10] media: ar0521: Implement enum_frame_sizes Jacopo Mondi
2022-10-06 14:37 ` Dave Stevenson
2022-10-06 16:33 ` Laurent Pinchart
2022-10-07 4:57 ` Krzysztof Hałasa
2022-10-07 8:08 ` Laurent Pinchart
2022-10-07 7:29 ` Jacopo Mondi
2022-10-07 8:11 ` Laurent Pinchart
2022-10-07 10:32 ` Dave Stevenson
2022-10-07 12:05 ` Sakari Ailus
2022-10-07 12:12 ` Laurent Pinchart
2022-10-05 19:06 ` [PATCH 02/10] media: ar0521: Add V4L2_CID_ANALOG_GAIN Jacopo Mondi
2022-10-06 14:44 ` Dave Stevenson
2022-10-06 15:00 ` Jacopo Mondi
2022-10-06 15:05 ` Laurent Pinchart
2022-10-07 5:28 ` Krzysztof Hałasa
2022-10-07 8:20 ` Laurent Pinchart
2022-10-12 18:54 ` Sakari Ailus
2022-10-13 9:30 ` Laurent Pinchart
2022-10-07 5:20 ` Krzysztof Hałasa
2022-10-07 7:17 ` Jacopo Mondi
2022-10-07 8:30 ` Laurent Pinchart
2022-10-07 12:01 ` Krzysztof Hałasa
2022-10-07 12:07 ` Laurent Pinchart
2022-10-07 14:02 ` Krzysztof Hałasa
2022-10-17 15:10 ` Jacopo Mondi
2022-10-17 15:57 ` Sakari Ailus
2022-10-17 16:31 ` Jacopo Mondi
2022-10-17 16:37 ` Sakari Ailus
2022-10-17 16:42 ` Dave Stevenson
2022-10-07 11:56 ` Krzysztof Hałasa
2022-10-07 12:11 ` Laurent Pinchart
2022-10-07 14:00 ` Krzysztof Hałasa
2022-10-05 19:06 ` [PATCH 03/10] media: ar0521: Set maximum resolution to 2592x1944 Jacopo Mondi
2022-10-06 14:57 ` Dave Stevenson
2022-10-07 13:06 ` Laurent Pinchart
2022-10-20 11:23 ` Jacopo Mondi
2022-10-07 5:33 ` Krzysztof Hałasa
2022-10-07 12:42 ` Jacopo Mondi
2022-10-07 14:07 ` Krzysztof Hałasa
2022-10-05 19:06 ` [PATCH 04/10] media: ar0521: Rework PLL computation Jacopo Mondi
2022-10-07 13:56 ` Laurent Pinchart
2022-10-12 19:02 ` Sakari Ailus
2022-10-13 9:31 ` Laurent Pinchart
2022-10-05 19:06 ` [PATCH 05/10] media: ar0521: Add LINK_FREQ control Jacopo Mondi
2022-10-06 15:10 ` Dave Stevenson
2022-10-07 14:01 ` Laurent Pinchart
2022-10-07 14:26 ` Dave Stevenson
2022-10-16 1:53 ` Laurent Pinchart
2022-10-17 11:21 ` Dave Stevenson
2022-10-17 9:24 ` Jacopo Mondi
2022-10-17 11:00 ` Dave Stevenson
2022-10-17 12:00 ` Jacopo Mondi
2022-10-05 19:06 ` [PATCH 06/10] media: ar0521: Configure pixel rate using LINK_FREQ Jacopo Mondi
2022-10-06 5:51 ` kernel test robot
2022-10-06 15:42 ` Sakari Ailus
2022-10-07 7:25 ` Jacopo Mondi
2022-10-07 5:52 ` Krzysztof Hałasa
2022-10-05 19:06 ` [PATCH 07/10] media: ar0521: Adjust exposure and blankings limits Jacopo Mondi
2022-10-06 2:08 ` kernel test robot
2022-10-06 4:17 ` kernel test robot
2022-10-06 15:41 ` Dave Stevenson
2022-10-05 19:06 ` [PATCH 08/10] media: ar0521: Setup controls at s_stream time Jacopo Mondi
2022-10-06 15:43 ` Dave Stevenson
2022-10-07 7:23 ` Jacopo Mondi
2022-10-05 19:06 ` Jacopo Mondi [this message]
2022-10-06 15:45 ` [PATCH 09/10] media: ar0521: Rework startup sequence Dave Stevenson
2022-10-05 19:06 ` [PATCH 10/10] media: ar0521: Tab-align definitions Jacopo Mondi
2022-10-06 15:48 ` Dave Stevenson
2022-10-06 16:11 ` Laurent Pinchart
2022-10-07 5:42 ` Krzysztof Hałasa
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221005190613.394277-10-jacopo@jmondi.org \
--to=jacopo@jmondi.org \
--cc=khalasa@piap.pl \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=sakari.ailus@iki.fi \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).