linux-media.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: "Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>
Cc: Kieran Bingham <kieran.bingham@ideasonboard.com>,
	Jacopo Mondi <jacopo@jmondi.org>,
	linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH v3 4/4] i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter
Date: Mon, 05 Nov 2018 13:01:43 +0200	[thread overview]
Message-ID: <2284392.jROv1qFbmM@avalon> (raw)
In-Reply-To: <20181102160009.17267-5-niklas.soderlund+renesas@ragnatech.se>

Hi Niklas,

Thank you for the patch.

On Friday, 2 November 2018 18:00:09 EET Niklas Söderlund wrote:
> The driver fixed the TXA CSI-2 transmitter in 4-lane mode while it could
> operate using 1-, 2- and 4-lanes. Update the driver to support all modes
> the hardware does.

"all modes the hardware does" sounds weird. How about simple "all available 
modes" ?

> The driver make use of large tables of static register/value writes when

s/make/makes/

> powering up/down the TXA and TXB transmitters which include the write to
> the NUM_LANES register. By converting the tables into functions and
> using parameters the power up/down functions for TXA and TXB power
> up/down can be merged and used for both transmitters.
> 
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The code looks so much better now :-)

> ---
> * Changes since v2
> - Fix typos in comments.
> - Remove unneeded boiler plait code in adv748x_tx_power() as suggested
>   by Jacopo and Laurent.
> - Take into account the two different register used when powering up TXA
>   and TXB due to an earlier patch in this series aligns the power
>   sequence with the manual.
> 
> * Changes since v1
> - Convert tables of register/value writes into functions instead of
>   intercepting and modifying the writes to the NUM_LANES register.
> ---
>  drivers/media/i2c/adv748x/adv748x-core.c | 157 ++++++++++++-----------
>  1 file changed, 79 insertions(+), 78 deletions(-)
> 
> diff --git a/drivers/media/i2c/adv748x/adv748x-core.c
> b/drivers/media/i2c/adv748x/adv748x-core.c index
> 9d80d7f3062b16bc..d94c63cb6a2efdba 100644
> --- a/drivers/media/i2c/adv748x/adv748x-core.c
> +++ b/drivers/media/i2c/adv748x/adv748x-core.c
> @@ -125,6 +125,16 @@ int adv748x_write(struct adv748x_state *state, u8 page,
> u8 reg, u8 value) return regmap_write(state->regmap[page], reg, value);
>  }
> 
> +static int adv748x_write_check(struct adv748x_state *state, u8 page, u8
> reg,
> +			       u8 value, int *error)
> +{
> +	if (*error)
> +		return *error;
> +
> +	*error = adv748x_write(state, page, reg, value);
> +	return *error;
> +}
> +
>  /* adv748x_write_block(): Write raw data with a maximum of
> I2C_SMBUS_BLOCK_MAX * size to one or more registers.
>   *
> @@ -231,79 +241,77 @@ static int adv748x_write_regs(struct adv748x_state
> *state, * TXA and TXB
>   */
> 
> -static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = {
> -
> -	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
> -	{ADV748X_PAGE_TXA, 0x00, 0xa4},	/* Set Auto DPHY Timing */
> -	{ADV748X_PAGE_TXA, 0xdb, 0x10},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xd6, 0x07},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xc4, 0x0a},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x71, 0x33},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x72, 0x11},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
> -
> -	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x1e, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
> -	{ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXA, 0xc1, 0x2b},	/* ADI Required Write */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXA, 0x31, 0x80},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = {
> -
> -	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x1e, 0x00},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
> -	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_TXA, 0xc1, 0x3b},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = {
> -
> -	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
> -	{ADV748X_PAGE_TXB, 0x00, 0xa1},	/* Set Auto DPHY Timing */
> -	{ADV748X_PAGE_TXB, 0xd2, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xc4, 0x0a},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x71, 0x33},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x72, 0x11},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
> -
> -	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x1e, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
> -	{ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXB, 0xc1, 0x2b},	/* ADI Required Write */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXB, 0x31, 0x80},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = {
> -
> -	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x1e, 0x00},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
> -	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_TXB, 0xc1, 0x3b},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> +static int adv748x_power_up_tx(struct adv748x_csi2 *tx)
> +{
> +	struct adv748x_state *state = tx->state;
> +	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
> +	int ret = 0;
> +
> +	/* Enable n-lane MIPI */
> +	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
> +
> +	/* Set Auto DPHY Timing */
> +	adv748x_write_check(state, page, 0x00, 0xa0 | tx->num_lanes, &ret);
> +
> +	/* ADI Required Write */
> +	if (is_txa(tx)) {
> +		adv748x_write_check(state, page, 0xdb, 0x10, &ret);
> +		adv748x_write_check(state, page, 0xd6, 0x07, &ret);
> +	} else {
> +		adv748x_write_check(state, page, 0xd2, 0x40, &ret);
> +	}
> +
> +	adv748x_write_check(state, page, 0xc4, 0x0a, &ret);
> +	adv748x_write_check(state, page, 0x71, 0x33, &ret);
> +	adv748x_write_check(state, page, 0x72, 0x11, &ret);
> +
> +	/* i2c_dphy_pwdn - 1'b0 */
> +	adv748x_write_check(state, page, 0xf0, 0x00, &ret);
> +
> +	/* ADI Required Writes*/
> +	adv748x_write_check(state, page, 0x31, 0x82, &ret);
> +	adv748x_write_check(state, page, 0x1e, 0x40, &ret);
> +
> +	/* i2c_mipi_pll_en - 1'b1 */
> +	adv748x_write_check(state, page, 0xda, 0x01, &ret);
> +	usleep_range(2000, 2500);
> +
> +	/* Power-up CSI-TX */
> +	adv748x_write_check(state, page, 0x00, 0x20 | tx->num_lanes, &ret);
> +	usleep_range(1000, 1500);
> +
> +	/* ADI Required Writes */
> +	adv748x_write_check(state, page, 0xc1, 0x2b, &ret);
> +	usleep_range(1000, 1500);
> +	adv748x_write_check(state, page, 0x31, 0x80, &ret);
> +
> +	return ret;
> +}
> +
> +static int adv748x_power_down_tx(struct adv748x_csi2 *tx)
> +{
> +	struct adv748x_state *state = tx->state;
> +	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
> +	int ret = 0;
> +
> +	/* ADI Required Writes */
> +	adv748x_write_check(state, page, 0x31, 0x82, &ret);
> +	adv748x_write_check(state, page, 0x1e, 0x00, &ret);
> +
> +	/* Enable n-lane MIPI */
> +	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
> +
> +	/* i2c_mipi_pll_en - 1'b1 */
> +	adv748x_write_check(state, page, 0xda, 0x01, &ret);
> +
> +	/* ADI Required Write */
> +	adv748x_write_check(state, page, 0xc1, 0x3b, &ret);
> +
> +	return ret;
> +}
> 
>  int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
>  {
> -	struct adv748x_state *state = tx->state;
> -	const struct adv748x_reg_value *reglist;
>  	int val;
> 
>  	if (!is_tx_enabled(tx))
> @@ -321,14 +329,7 @@ int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
>  	WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN),
>  			"Enabling with unknown bit set");
> 
> -	if (on)
> -		reglist = is_txa(tx) ? adv748x_power_up_txa_4lane :
> -				       adv748x_power_up_txb_1lane;
> -	else
> -		reglist = is_txa(tx) ? adv748x_power_down_txa_4lane :
> -				       adv748x_power_down_txb_1lane;
> -
> -	return adv748x_write_regs(state, reglist);
> +	return on ? adv748x_power_up_tx(tx) : adv748x_power_down_tx(tx);
>  }
> 
>  /* ------------------------------------------------------------------------

-- 
Regards,

Laurent Pinchart

  parent reply	other threads:[~2018-11-05 20:20 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-02 16:00 [PATCH v3 0/4] i2c: adv748x: add support for CSI-2 TXA to work Niklas Söderlund
2018-11-02 16:00 ` [PATCH v3 1/4] dt-bindings: adv748x: make data-lanes property mandatory for CSI-2 endpoints Niklas Söderlund
2018-11-05  8:41   ` jacopo mondi
2018-11-05 20:39     ` Rob Herring
2018-11-05 10:43   ` Laurent Pinchart
2018-11-02 16:00 ` [PATCH v3 2/4] i2c: adv748x: reuse power up sequence when initializing CSI-2 Niklas Söderlund
2018-11-05 10:52   ` Laurent Pinchart
2018-11-02 16:00 ` [PATCH v3 3/4] i2c: adv748x: store number of CSI-2 lanes described in device tree Niklas Söderlund
2018-11-05  8:58   ` jacopo mondi
2018-11-05 10:56   ` Laurent Pinchart
2018-11-02 16:00 ` [PATCH v3 4/4] i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter Niklas Söderlund
2018-11-05  8:47   ` jacopo mondi
2018-11-05 11:01   ` Laurent Pinchart [this message]
2018-11-23 14:01   ` jacopo mondi
2018-11-23 14:43     ` Laurent Pinchart
2018-11-25 10:09       ` jacopo mondi
2018-11-05 10:19 ` [PATCH v3 0/4] i2c: adv748x: add support for CSI-2 TXA to work jacopo mondi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=2284392.jROv1qFbmM@avalon \
    --to=laurent.pinchart@ideasonboard.com \
    --cc=jacopo@jmondi.org \
    --cc=kieran.bingham@ideasonboard.com \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=niklas.soderlund+renesas@ragnatech.se \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).