Linux-Media Archive on lore.kernel.org
 help / color / Atom feed
From: Tomasz Figa <tfiga@chromium.org>
To: Sakari Ailus <sakari.ailus@linux.intel.com>,
	Dongchun Zhu <dongchun.zhu@mediatek.com>
Cc: "Linus Walleij" <linus.walleij@linaro.org>,
	"Bartosz Golaszewski" <bgolaszewski@baylibre.com>,
	"Mauro Carvalho Chehab" <mchehab@kernel.org>,
	"Andy Shevchenko" <andriy.shevchenko@linux.intel.com>,
	"Rob Herring" <robh+dt@kernel.org>,
	"Mark Rutland" <mark.rutland@arm.com>,
	"Nicolas Boichat" <drinkcat@chromium.org>,
	"Matthias Brugger" <matthias.bgg@gmail.com>,
	"Cao Bing Bu" <bingbu.cao@intel.com>,
	srv_heupstream <srv_heupstream@mediatek.com>,
	"moderated list:ARM/Mediatek SoC support"
	<linux-mediatek@lists.infradead.org>,
	"list@263.net:IOMMU DRIVERS <iommu@lists.linux-foundation.org>,
	Joerg Roedel <joro@8bytes.org>,"
	<linux-arm-kernel@lists.infradead.org>,
	"Sj Huang" <sj.huang@mediatek.com>,
	"Linux Media Mailing List" <linux-media@vger.kernel.org>,
	linux-devicetree <devicetree@vger.kernel.org>,
	"Louis Kuo" <louis.kuo@mediatek.com>,
	"Shengnan Wang (王圣男)" <shengnan.wang@mediatek.com>
Subject: Re: [V5, 2/2] media: i2c: dw9768: Add DW9768 VCM driver
Date: Thu, 7 May 2020 15:46:31 +0200
Message-ID: <CAAFQd5DO9FGx9OF2RpcSprg0oLiVuS90w2qLAHCOSc3w6tKUWw@mail.gmail.com> (raw)
In-Reply-To: <20200507131220.GC9190@paasikivi.fi.intel.com>

Hi Sakari, Dongchun,

On Thu, May 7, 2020 at 3:12 PM Sakari Ailus
<sakari.ailus@linux.intel.com> wrote:
>
> HI Dongchun,
>
> On Thu, May 07, 2020 at 08:45:24PM +0800, Dongchun Zhu wrote:
> > Hi Sakari,
> >
> > Thanks for the review.
> >
> > On Wed, 2020-05-06 at 18:13 +0300, Sakari Ailus wrote:
> > > Hi Dongchun,
> > >
> > > On Sun, May 03, 2020 at 12:17:27AM +0800, Dongchun Zhu wrote:
> > > > Add a V4L2 sub-device driver for DW9768 voice coil motor, providing
> > > > control to set the desired focus via IIC serial interface.
> > > >
> > > > Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
> > > > ---
> > > >  MAINTAINERS                |   1 +
> > > >  drivers/media/i2c/Kconfig  |  11 ++
> > > >  drivers/media/i2c/Makefile |   1 +
> > > >  drivers/media/i2c/dw9768.c | 440 +++++++++++++++++++++++++++++++++++++++++++++
> > > >  4 files changed, 453 insertions(+)
> > > >  create mode 100644 drivers/media/i2c/dw9768.c
> > > >
> > > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > > index 8d72c41..c92dc99 100644
> > > > --- a/MAINTAINERS
> > > > +++ b/MAINTAINERS
> > > > @@ -5157,6 +5157,7 @@ L:  linux-media@vger.kernel.org
> > > >  S:       Maintained
> > > >  T:       git git://linuxtv.org/media_tree.git
> > > >  F:       Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.yaml
> > > > +F:       drivers/media/i2c/dw9768.c
> > > >
> > > >  DONGWOON DW9807 LENS VOICE COIL DRIVER
> > > >  M:       Sakari Ailus <sakari.ailus@linux.intel.com>
> > > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > > > index 125d596..6a3f9da 100644
> > > > --- a/drivers/media/i2c/Kconfig
> > > > +++ b/drivers/media/i2c/Kconfig
> > > > @@ -1040,6 +1040,17 @@ config VIDEO_DW9714
> > > >     capability. This is designed for linear control of
> > > >     voice coil motors, controlled via I2C serial interface.
> > > >
> > > > +config VIDEO_DW9768
> > > > + tristate "DW9768 lens voice coil support"
> > > > + depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER
> > > > + depends on VIDEO_V4L2_SUBDEV_API
> > >
> > > Please check how this works in the media tree master branch now --- it's
> > > largely select based.
> > >
> >
> > The actuator driver uses some structures that require the
> > VIDEO_V4L2_SUBDEV_API code, so here we add VIDEO_V4L2_SUBDEV_API
> > dependency to avoid possible build error when it's not enabled.
>
> Please make sure this works with current media tree master. Right now it
> does not.
>

Dongchun, as Sakari said, please make sure to base the patches on the
master branch of the media tree.
(https://git.linuxtv.org/media_tree.git/). The approach for Kconfig
dependency selection there seems to have changed recently.

> >
> > > In general the patch seems fine to me, but please see the other comments
> > > below, too.
> > >
> > > > + depends on PM
> > > > + help
> > > > +   This is a driver for the DW9768 camera lens voice coil.
> > > > +   DW9768 is a 10 bit DAC with 100mA output current sink
> > > > +   capability. This is designed for linear control of
> > > > +   voice coil motors, controlled via I2C serial interface.
> > > > +
> > > >  config VIDEO_DW9807_VCM
> > > >   tristate "DW9807 lens voice coil support"
> > > >   depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER
> > > > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> > > > index 77bf7d0..4057476 100644
> > > > --- a/drivers/media/i2c/Makefile
> > > > +++ b/drivers/media/i2c/Makefile
> > > > @@ -24,6 +24,7 @@ obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o
> > > >  obj-$(CONFIG_VIDEO_AD5820)  += ad5820.o
> > > >  obj-$(CONFIG_VIDEO_AK7375)  += ak7375.o
> > > >  obj-$(CONFIG_VIDEO_DW9714)  += dw9714.o
> > > > +obj-$(CONFIG_VIDEO_DW9768)  += dw9768.o
> > > >  obj-$(CONFIG_VIDEO_DW9807_VCM)  += dw9807-vcm.o
> > > >  obj-$(CONFIG_VIDEO_ADV7170) += adv7170.o
> > > >  obj-$(CONFIG_VIDEO_ADV7175) += adv7175.o
> > > > diff --git a/drivers/media/i2c/dw9768.c b/drivers/media/i2c/dw9768.c
> > > > new file mode 100644
> > > > index 0000000..dd68534
> > > > --- /dev/null
> > > > +++ b/drivers/media/i2c/dw9768.c
> > > > @@ -0,0 +1,440 @@
> > > > +// SPDX-License-Identifier: GPL-2.0
> > > > +// Copyright (c) 2020 MediaTek Inc.
> > > > +
> > > > +#include <linux/delay.h>
> > > > +#include <linux/i2c.h>
> > > > +#include <linux/module.h>
> > > > +#include <linux/pm_runtime.h>
> > > > +#include <linux/regulator/consumer.h>
> > > > +#include <media/v4l2-async.h>
> > > > +#include <media/v4l2-ctrls.h>
> > > > +#include <media/v4l2-device.h>
> > > > +#include <media/v4l2-subdev.h>
> > > > +
> > > > +#define DW9768_NAME                              "dw9768"
> > > > +#define DW9768_MAX_FOCUS_POS                     (1024 - 1)
> > > > +/*
> > > > + * This sets the minimum granularity for the focus positions.
> > > > + * A value of 1 gives maximum accuracy for a desired focus position
> > > > + */
> > > > +#define DW9768_FOCUS_STEPS                       1
> > > > +
> > > > +/*
> > > > + * Ring control and Power control register
> > > > + * Bit[1] RING_EN
> > > > + * 0: Direct mode
> > > > + * 1: AAC mode (ringing control mode)
> > > > + * Bit[0] PD
> > > > + * 0: Normal operation mode
> > > > + * 1: Power down mode
> > > > + * DW9768 requires waiting time of Topr after PD reset takes place.
> > > > + */
> > > > +#define DW9768_RING_PD_CONTROL_REG               0x02
> > > > +#define DW9768_PD_MODE_OFF                       0x00
> > > > +#define DW9768_PD_MODE_EN                        BIT(0)
> > > > +#define DW9768_AAC_MODE_EN                       BIT(1)
> > > > +
> > > > +/*
> > > > + * DW9768 separates two registers to control the VCM position.
> > > > + * One for MSB value, another is LSB value.
> > > > + * DAC_MSB: D[9:8] (ADD: 0x03)
> > > > + * DAC_LSB: D[7:0] (ADD: 0x04)
> > > > + * D[9:0] DAC data input: positive output current = D[9:0] / 1023 * 100[mA]
> > > > + */
> > > > +#define DW9768_MSB_ADDR                          0x03
> > > > +#define DW9768_LSB_ADDR                          0x04
> > > > +#define DW9768_STATUS_ADDR                       0x05
> > > > +
> > > > +/*
> > > > + * AAC mode control & prescale register
> > > > + * Bit[7:5] Namely AC[2:0], decide the VCM mode and operation time.
> > > > + * 000 Direct(default)
> > > > + * 001 AAC2 0.48xTvib
> > > > + * 010 AAC3 0.70xTvib
> > > > + * 011 AAC4 0.75xTvib
> > > > + * 100 Reserved
> > > > + * 101 AAC8 1.13xTvib
> > > > + * 110 Reserved
> > > > + * 111 Reserved
> > > > + * Bit[2:0] Namely PRESC[2:0], set the internal clock dividing rate as follow.
> > > > + * 000 2
> > > > + * 001 1(default)
> > > > + * 010 1/2
> > > > + * 011 1/4
> > > > + * 100 8
> > > > + * 101 4
> > > > + * 110 Reserved
> > > > + * 111 Reserved
> > > > + */
> > > > +#define DW9768_AAC_PRESC_REG                     0x06
> > > > +#define DW9768_AAC3_SELECT_DIVIDING_RATE_1       0x41
> > >
> > > I guess we can start with these values. But I can't think of another option
> > > than putting them into DT if there are differences between what hardware
> > > platforms require.
> > >
> >
> > Let's have a discussion about this.
> > Now these non-default register settings represent one AAC operation
> > mode, this is one option and works for a given lens or a module.
> > If sometime in the future hardware platforms require another different
> > settings, then DT properties may need to be created.
>
> If these values indeed are specific to a given lens (and presumably also a
> spring), then I'd put them to DT right now --- we don't have drivers for
> these components the drivers of which could hold this information, nor it
> makes sense to add them just for that.
>

I tend to stay on the conservative side and only add DT properties
once there is really a need to do so. Right now we haven't seen any
system which would use different values of these parameters.

Best regards,
Tomasz

> >
> > > > +
> > > > +/*
> > > > + * VCM period of vibration register
> > > > + * Bit[5:0] Defined as VCM rising periodic time (Tvib) together with PRESC[2:0]
> > > > + * Tvib = (6.3ms + AACT[5:0] * 0.1ms) * Dividing Rate
> > > > + * Dividing Rate is the internal clock dividing rate that is defined at
> > > > + * PRESCALE register (ADD: 0x06)
> > > > + */
> > > > +#define DW9768_AAC_TIME_REG                      0x07
> > > > +#define DW9768_AACT_CNT                          0x39
> > > > +
> > > > +/*
> > > > + * DW9768 requires waiting time (delay time) of t_OPR after power-up,
> > > > + * or in the case of PD reset taking place.
> > > > + */
> > > > +#define DW9768_T_OPR_US                          1000
> > > > +
> > > > +/*
> > > > + * This acts as the minimum granularity of lens movement.
> > > > + * Keep this value power of 2, so the control steps can be
> > > > + * uniformly adjusted for gradual lens movement, with desired
> > > > + * number of control steps.
> > > > + */
> > > > +#define DW9768_MOVE_STEPS                        16
> > > > +
> > > > +/*
> > > > + * DW9768_AAC_PRESC_REG & DW9768_AAC_TIME_REG determine VCM operation time.
> > > > + * If DW9768_AAC_PRESC_REG is 0x41, and DW9768_AAC_TIME_REG is 0x39, VCM mode
> > > > + * would be AAC3, Operation Time would be 0.70xTvib, that is 8.40ms.
> > > > + */
> > > > +#define DW9768_MOVE_DELAY_US                     8400
> > > > +#define DW9768_STABLE_TIME_US                    20000
> > > > +
> > > > +static const char * const dw9768_supply_names[] = {
> > > > + "vin",  /* I2C I/O interface power */
> > > > + "vdd",  /* VCM power */
> > > > +};
> > > > +
> > > > +/* dw9768 device structure */
> > > > +struct dw9768 {
> > > > + struct regulator_bulk_data supplies[ARRAY_SIZE(dw9768_supply_names)];
> > > > + struct v4l2_ctrl_handler ctrls;
> > > > + struct v4l2_ctrl *focus;
> > > > + struct v4l2_subdev sd;
> > > > +};
> > > > +
> > > > +static inline struct dw9768 *to_dw9768(struct v4l2_ctrl *ctrl)
> > > > +{
> > > > + return container_of(ctrl->handler, struct dw9768, ctrls);
> > > > +}
> > >
> > > This is used in a single place. I'd just use container_of() directly there.
> > >
> >
> > Thanks for the reminder.
> > Fixed in next release.
> >
> > > > +
> > > > +static inline struct dw9768 *sd_to_dw9768(struct v4l2_subdev *subdev)
> > > > +{
> > > > + return container_of(subdev, struct dw9768, sd);
> > > > +}
> > > > +
> > > > +struct regval_list {
> > > > + u8 reg_num;
> > > > + u8 value;
> > > > +};
> > > > +
> > > > +static const struct regval_list dw9768_init_regs[] = {
> > > > + {DW9768_RING_PD_CONTROL_REG, DW9768_AAC_MODE_EN},
> > > > + {DW9768_AAC_PRESC_REG, DW9768_AAC3_SELECT_DIVIDING_RATE_1},
> > > > + {DW9768_AAC_TIME_REG, DW9768_AACT_CNT},
> > > > +};
> > > > +
> > > > +static int dw9768_write_array(struct dw9768 *dw9768,
> > > > +                       const struct regval_list *vals, size_t len)
> > > > +{
> > > > + struct i2c_client *client = v4l2_get_subdevdata(&dw9768->sd);
> > > > + unsigned int i;
> > > > + int ret;
> > > > +
> > > > + for (i = 0; i < len; i++) {
> > > > +         ret = i2c_smbus_write_byte_data(client, vals[i].reg_num,
> > > > +                                         vals[i].value);
> > > > +         if (ret < 0)
> > > > +                 return ret;
> > > > + }
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int dw9768_set_dac(struct dw9768 *dw9768, u16 val)
> > > > +{
> > > > + struct i2c_client *client = v4l2_get_subdevdata(&dw9768->sd);
> > > > +
> > > > + /* Write VCM position to registers */
> > > > + return i2c_smbus_write_word_swapped(client, DW9768_MSB_ADDR, val);
> > > > +}
> > > > +
> > > > +static int dw9768_init(struct dw9768 *dw9768)
> > > > +{
> > > > + struct i2c_client *client = v4l2_get_subdevdata(&dw9768->sd);
> > > > + int ret, val;
> > > > +
> > > > + /* Reset DW9768_RING_PD_CONTROL_REG to default status 0x00 */
> > > > + ret = i2c_smbus_write_byte_data(client, DW9768_RING_PD_CONTROL_REG,
> > > > +                                 DW9768_PD_MODE_OFF);
> > > > + if (ret < 0)
> > > > +         return ret;
> > > > +
> > > > + /*
> > > > +  * DW9769 requires waiting delay time of t_OPR
> > > > +  * after PD reset takes place.
> > > > +  */
> > > > + usleep_range(DW9768_T_OPR_US, DW9768_T_OPR_US + 100);
> > > > +
> > > > + ret = dw9768_write_array(dw9768, dw9768_init_regs,
> > > > +                          ARRAY_SIZE(dw9768_init_regs));
> > > > + if (ret)
> > > > +         return ret;
> > > > +
> > > > + for (val = dw9768->focus->val % DW9768_MOVE_STEPS;
> > > > +      val <= dw9768->focus->val;
> > > > +      val += DW9768_MOVE_STEPS) {
> > > > +         ret = dw9768_set_dac(dw9768, val);
> > > > +         if (ret) {
> > > > +                 dev_err(&client->dev, "%s I2C failure: %d",
> > > > +                         __func__, ret);
> > > > +                 return ret;
> > > > +         }
> > > > +         usleep_range(DW9768_MOVE_DELAY_US,
> > > > +                      DW9768_MOVE_DELAY_US + 1000);
> > > > + }
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int dw9768_release(struct dw9768 *dw9768)
> > > > +{
> > > > + struct i2c_client *client = v4l2_get_subdevdata(&dw9768->sd);
> > > > + int ret, val;
> > > > +
> > > > + val = round_down(dw9768->focus->val, DW9768_MOVE_STEPS);
> > > > + for ( ; val >= 0; val -= DW9768_MOVE_STEPS) {
> > > > +         ret = dw9768_set_dac(dw9768, val);
> > > > +         if (ret) {
> > > > +                 dev_err(&client->dev, "I2C write fail: %d", ret);
> > > > +                 return ret;
> > > > +         }
> > > > +         usleep_range(DW9768_MOVE_DELAY_US, DW9768_MOVE_DELAY_US + 1000);
> > > > + }
> > > > +
> > > > + /*
> > > > +  * Wait for the motor to stabilize after the last movement
> > > > +  * to prevent the motor from shaking.
> > > > +  */
> > > > + usleep_range(DW9768_STABLE_TIME_US - DW9768_MOVE_DELAY_US,
> > > > +              DW9768_STABLE_TIME_US - DW9768_MOVE_DELAY_US + 1000);
> > > > +
> > > > + ret = i2c_smbus_write_byte_data(client, DW9768_RING_PD_CONTROL_REG,
> > > > +                                 DW9768_PD_MODE_EN);
> > > > + if (ret < 0)
> > > > +         return ret;
> > > > +
> > > > + /*
> > > > +  * DW9769 requires waiting delay time of t_OPR
> > > > +  * after PD reset takes place.
> > > > +  */
> > > > + usleep_range(DW9768_T_OPR_US, DW9768_T_OPR_US + 100);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int __maybe_unused dw9768_runtime_suspend(struct device *dev)
> > > > +{
> > > > + struct i2c_client *client = to_i2c_client(dev);
> > > > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > > > + struct dw9768 *dw9768 = sd_to_dw9768(sd);
> > > > +
> > > > + dw9768_release(dw9768);
> > > > + regulator_bulk_disable(ARRAY_SIZE(dw9768_supply_names),
> > > > +                        dw9768->supplies);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int __maybe_unused dw9768_runtime_resume(struct device *dev)
> > > > +{
> > > > + struct i2c_client *client = to_i2c_client(dev);
> > > > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > > > + struct dw9768 *dw9768 = sd_to_dw9768(sd);
> > > > + int ret;
> > > > +
> > > > + ret = regulator_bulk_enable(ARRAY_SIZE(dw9768_supply_names),
> > > > +                             dw9768->supplies);
> > > > + if (ret < 0) {
> > > > +         dev_err(dev, "failed to enable regulators\n");
> > > > +         return ret;
> > > > + }
> > > > +
> > > > + /*
> > > > +  * The datasheet refers to t_OPR that needs to be waited before sending
> > > > +  * I2C commands after power-up.
> > > > +  */
> > > > + usleep_range(DW9768_T_OPR_US, DW9768_T_OPR_US + 100);
> > > > +
> > > > + ret = dw9768_init(dw9768);
> > > > + if (ret < 0)
> > > > +         goto disable_regulator;
> > > > +
> > > > + return 0;
> > > > +
> > > > +disable_regulator:
> > > > + regulator_bulk_disable(ARRAY_SIZE(dw9768_supply_names),
> > > > +                        dw9768->supplies);
> > > > +
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static int dw9768_set_ctrl(struct v4l2_ctrl *ctrl)
> > > > +{
> > > > + struct dw9768 *dw9768 = to_dw9768(ctrl);
> > > > +
> > > > + if (ctrl->id == V4L2_CID_FOCUS_ABSOLUTE)
> > > > +         return dw9768_set_dac(dw9768, ctrl->val);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static const struct v4l2_ctrl_ops dw9768_ctrl_ops = {
> > > > + .s_ctrl = dw9768_set_ctrl,
> > > > +};
> > > > +
> > > > +static int dw9768_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> > > > +{
> > > > + int ret;
> > > > +
> > > > + ret = pm_runtime_get_sync(sd->dev);
> > > > + if (ret < 0) {
> > > > +         pm_runtime_put_noidle(sd->dev);
> > > > +         return ret;
> > > > + }
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int dw9768_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> > > > +{
> > > > + pm_runtime_put(sd->dev);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static const struct v4l2_subdev_internal_ops dw9768_int_ops = {
> > > > + .open = dw9768_open,
> > > > + .close = dw9768_close,
> > > > +};
> > > > +
> > > > +static const struct v4l2_subdev_ops dw9768_ops = { };
> > > > +
> > > > +static int dw9768_init_controls(struct dw9768 *dw9768)
> > > > +{
> > > > + struct v4l2_ctrl_handler *hdl = &dw9768->ctrls;
> > > > + const struct v4l2_ctrl_ops *ops = &dw9768_ctrl_ops;
> > > > +
> > > > + v4l2_ctrl_handler_init(hdl, 1);
> > > > +
> > > > + dw9768->focus = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_FOCUS_ABSOLUTE, 0,
> > > > +                                   DW9768_MAX_FOCUS_POS,
> > > > +                                   DW9768_FOCUS_STEPS, 0);
> > > > +
> > > > + if (hdl->error)
> > > > +         return hdl->error;
> > > > +
> > > > + dw9768->sd.ctrl_handler = hdl;
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int dw9768_probe(struct i2c_client *client)
> > > > +{
> > > > + struct device *dev = &client->dev;
> > > > + struct dw9768 *dw9768;
> > > > + unsigned int i;
> > > > + int ret;
> > > > +
> > > > + dw9768 = devm_kzalloc(dev, sizeof(*dw9768), GFP_KERNEL);
> > > > + if (!dw9768)
> > > > +         return -ENOMEM;
> > > > +
> > > > + v4l2_i2c_subdev_init(&dw9768->sd, client, &dw9768_ops);
> > > > +
> > > > + for (i = 0; i < ARRAY_SIZE(dw9768_supply_names); i++)
> > > > +         dw9768->supplies[i].supply = dw9768_supply_names[i];
> > > > +
> > > > + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(dw9768_supply_names),
> > > > +                               dw9768->supplies);
> > > > + if (ret) {
> > > > +         dev_err(dev, "failed to get regulators\n");
> > > > +         return ret;
> > > > + }
> > > > +
> > > > + ret = dw9768_init_controls(dw9768);
> > > > + if (ret)
> > > > +         goto entity_cleanup;
> > > > +
> > > > + dw9768->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > > > + dw9768->sd.internal_ops = &dw9768_int_ops;
> > > > +
> > > > + ret = media_entity_pads_init(&dw9768->sd.entity, 0, NULL);
> > > > + if (ret < 0)
> > > > +         goto entity_cleanup;
> > > > +
> > > > + dw9768->sd.entity.function = MEDIA_ENT_F_LENS;
> > > > +
> > > > + pm_runtime_enable(dev);
> > > > + if (!pm_runtime_enabled(dev)) {
> > > > +         ret = dw9768_runtime_resume(dev);
> > > > +         if (ret < 0) {
> > > > +                 dev_err(dev, "failed to power on: %d\n", ret);
> > > > +                 goto entity_cleanup;
> > > > +         }
> > > > + }
> > > > +
> > > > + ret = v4l2_async_register_subdev(&dw9768->sd);
> > > > + if (ret < 0)
> > > > +         goto entity_cleanup;
> > > > +
> > > > + return 0;
> > > > +
> > > > +entity_cleanup:
> > > > + v4l2_ctrl_handler_free(&dw9768->ctrls);
> > > > + media_entity_cleanup(&dw9768->sd.entity);
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static int dw9768_remove(struct i2c_client *client)
> > > > +{
> > > > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > > > + struct dw9768 *dw9768 = sd_to_dw9768(sd);
> > > > +
> > > > + pm_runtime_disable(&client->dev);
> > > > + v4l2_async_unregister_subdev(&dw9768->sd);
> > > > + v4l2_ctrl_handler_free(&dw9768->ctrls);
> > > > + media_entity_cleanup(&dw9768->sd.entity);
> > > > + if (!pm_runtime_status_suspended(&client->dev))
> > > > +         dw9768_runtime_suspend(&client->dev);
> > > > + pm_runtime_set_suspended(&client->dev);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static const struct of_device_id dw9768_of_table[] = {
> > > > + { .compatible = "dongwoon,dw9768" },
> > > > + {}
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, dw9768_of_table);
> > > > +
> > > > +static const struct dev_pm_ops dw9768_pm_ops = {
> > > > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> > > > +                         pm_runtime_force_resume)
> > > > + SET_RUNTIME_PM_OPS(dw9768_runtime_suspend, dw9768_runtime_resume, NULL)
> > > > +};
> > > > +
> > > > +static struct i2c_driver dw9768_i2c_driver = {
> > > > + .driver = {
> > > > +         .name = DW9768_NAME,
> > > > +         .pm = &dw9768_pm_ops,
> > > > +         .of_match_table = dw9768_of_table,
> > > > + },
> > > > + .probe_new  = dw9768_probe,
> > > > + .remove = dw9768_remove,
> > > > +};
> > > > +module_i2c_driver(dw9768_i2c_driver);
> > > > +
> > > > +MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
> > > > +MODULE_DESCRIPTION("DW9768 VCM driver");
> > > > +MODULE_LICENSE("GPL v2");
> > >
> >
>
> --
> Sakari Ailus

  reply index

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-05-02 16:17 [V5, 0/2] media: i2c: Add support for " Dongchun Zhu
2020-05-02 16:17 ` [V5, 1/2] media: dt-bindings: media: i2c: Document DW9768 bindings Dongchun Zhu
2020-05-05 19:15   ` Rob Herring
2020-05-02 16:17 ` [V5, 2/2] media: i2c: dw9768: Add DW9768 VCM driver Dongchun Zhu
2020-05-06 15:13   ` Sakari Ailus
2020-05-07 12:45     ` Dongchun Zhu
2020-05-07 13:12       ` Sakari Ailus
2020-05-07 13:46         ` Tomasz Figa [this message]
2020-05-07 14:00           ` Sakari Ailus
2020-05-08  3:27             ` Dongchun Zhu
2020-05-08  3:08           ` Dongchun Zhu
2020-05-08 21:13             ` Sakari Ailus
2020-05-09  2:23               ` Dongchun Zhu
2020-05-11 18:20                 ` Tomasz Figa
2020-05-12  3:33                   ` Dongchun Zhu
2020-05-12  8:58                     ` Sakari Ailus
2020-05-12 11:32                       ` Dongchun Zhu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CAAFQd5DO9FGx9OF2RpcSprg0oLiVuS90w2qLAHCOSc3w6tKUWw@mail.gmail.com \
    --to=tfiga@chromium.org \
    --cc=andriy.shevchenko@linux.intel.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=bingbu.cao@intel.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dongchun.zhu@mediatek.com \
    --cc=drinkcat@chromium.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-mediatek@lists.infradead.org \
    --cc=louis.kuo@mediatek.com \
    --cc=mark.rutland@arm.com \
    --cc=matthias.bgg@gmail.com \
    --cc=mchehab@kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=sakari.ailus@linux.intel.com \
    --cc=shengnan.wang@mediatek.com \
    --cc=sj.huang@mediatek.com \
    --cc=srv_heupstream@mediatek.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Media Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-media/0 linux-media/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-media linux-media/ https://lore.kernel.org/linux-media \
		linux-media@vger.kernel.org
	public-inbox-index linux-media

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-media


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git