From: Michael Kao <michael.kao@mediatek.com>
To: Zhang Rui <rui.zhang@intel.com>,
Eduardo Valentin <edubezval@gmail.com>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Matthias Brugger <matthias.bgg@gmail.com>, <hsinyi@chromium.org>,
<linux-pm@vger.kernel.org>, <srv_heupstream@mediatek.com>
Cc: devicetree@vger.kernel.org, linux-mediatek@lists.infradead.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
"michael.kao" <michael.kao@mediatek.com>
Subject: [PATCH v3,1/8] arm64: dts: mt8183: add thermal zone node
Date: Fri, 3 Jan 2020 14:44:00 +0800 [thread overview]
Message-ID: <20200103064407.19861-2-michael.kao@mediatek.com> (raw)
In-Reply-To: <20200103064407.19861-1-michael.kao@mediatek.com>
From: "michael.kao" <michael.kao@mediatek.com>
Add thermal zone node to Mediatek MT8183 dts file.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
---
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 85 ++++++++++++++++++++++++
1 file changed, 85 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index 10b32471bc7b..a2793cf3d994 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -570,6 +570,88 @@
status = "disabled";
};
+ thermal: thermal@1100b000 {
+ #thermal-sensor-cells = <1>;
+ compatible = "mediatek,mt8183-thermal";
+ reg = <0 0x1100b000 0 0x1000>;
+ interrupts = <0 76 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_THERM>,
+ <&infracfg CLK_INFRA_AUXADC>;
+ clock-names = "therm", "auxadc";
+ resets = <&infracfg MT8183_INFRACFG_AO_THERM_SW_RST>;
+ mediatek,auxadc = <&auxadc>;
+ mediatek,apmixedsys = <&apmixedsys>;
+ mediatek,hw-reset-temp = <117000>;
+ nvmem-cells = <&thermal_calibration>;
+ nvmem-cell-names = "calibration-data";
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu_thermal {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+ thermal-sensors = <&thermal 0>;
+ sustainable-power = <5000>;
+ };
+
+ /* The tzts1 ~ tzts6 don't need to polling */
+ /* The tzts1 ~ tzts6 don't need to thermal throttle */
+
+ tzts1: tzts1 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&thermal 1>;
+ sustainable-power = <5000>;
+ trips {};
+ cooling-maps {};
+ };
+
+ tzts2: tzts2 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&thermal 2>;
+ sustainable-power = <5000>;
+ trips {};
+ cooling-maps {};
+ };
+
+ tzts3: tzts3 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&thermal 3>;
+ sustainable-power = <5000>;
+ trips {};
+ cooling-maps {};
+ };
+
+ tzts4: tzts4 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&thermal 4>;
+ sustainable-power = <5000>;
+ trips {};
+ cooling-maps {};
+ };
+
+ tzts5: tzts5 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&thermal 5>;
+ sustainable-power = <5000>;
+ trips {};
+ cooling-maps {};
+ };
+
+ tztsABB: tztsABB {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&thermal 6>;
+ sustainable-power = <5000>;
+ trips {};
+ cooling-maps {};
+ };
+ };
+
audiosys: syscon@11220000 {
compatible = "mediatek,mt8183-audiosys", "syscon";
reg = <0 0x11220000 0 0x1000>;
@@ -580,6 +662,9 @@
compatible = "mediatek,mt8183-efuse",
"mediatek,efuse";
reg = <0 0x11f10000 0 0x1000>;
+ thermal_calibration: calib@180 {
+ reg = <0x180 0xc>;
+ };
};
mfgcfg: syscon@13000000 {
--
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
next prev parent reply other threads:[~2020-01-03 6:52 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-03 6:43 [PATCH v3,0/8] Add Mediatek thermal dirver and dtsi Michael Kao
2020-01-03 6:44 ` Michael Kao [this message]
2020-01-09 11:31 ` [PATCH v3,1/8] arm64: dts: mt8183: add thermal zone node Daniel Lezcano
2020-02-11 3:17 ` Michael Kao
2020-02-20 11:52 ` Daniel Lezcano
2020-02-20 20:57 ` Matthias Brugger
2020-02-26 1:58 ` Michael Kao
2020-02-20 20:56 ` Matthias Brugger
2020-01-03 6:44 ` [PATCH v3, 2/8] arm64: dts: mt8183: add/update dynamic power coefficients Michael Kao
2020-01-10 14:40 ` [PATCH v3,2/8] " Matthias Brugger
2020-02-11 2:05 ` Michael Kao
2020-02-20 21:06 ` Matthias Brugger
2020-01-03 6:44 ` [PATCH v3,3/8] arm64: dts: mt8183: Add #cooling-cells to CPU nodes Michael Kao
2020-02-20 21:59 ` Matthias Brugger
2020-01-03 6:44 ` [PATCH v3,4/8] arm64: dts: mt8183: Configure CPU cooling Michael Kao
2020-02-25 9:34 ` Michael Kao
2020-01-03 6:44 ` [PATCH v3, 5/8] arm64: dts: mt8183: Increase polling frequency for CPU thermal zone Michael Kao
2020-01-03 6:44 ` [PATCH v3,6/8] thermal: mediatek: mt8183: fix bank number settings Michael Kao
2020-01-08 9:58 ` [PATCH v3, 6/8] " Hsin-Yi Wang
2020-01-03 6:44 ` [PATCH v3, 7/8] thermal: mediatek: add another get_temp ops for thermal sensors Michael Kao
2020-01-03 6:44 ` [PATCH v3,8/8] thermal: mediatek: use spinlock to protect PTPCORESEL Michael Kao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200103064407.19861-2-michael.kao@mediatek.com \
--to=michael.kao@mediatek.com \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=edubezval@gmail.com \
--cc=hsinyi@chromium.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-pm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
--cc=srv_heupstream@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).