* [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook
@ 2020-06-25 10:17 Enric Balletbo i Serra
2020-06-25 10:17 ` [PATCH v2 1/7] dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-krane-sku176 Enric Balletbo i Serra
` (7 more replies)
0 siblings, 8 replies; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Sean Wang, Rob Herring,
Mars Cheng, hsinyi, matthias.bgg, linux-mediatek,
Collabora Kernel ML, linux-arm-kernel
These series adds basic support for the Lenovo IdeaPad Duet Chromebook, a
2-in-1 detachable devices using the MediaTek MT8183 SoC. The first patch
only adds the new compatible names in the mediatek binding. The second
patch, adds the missing compatible to instantiate the PMIC regulators.
The next patch adds missing devices to support better the board and fixes
some warnings found running dtbs_check. And finally, the latest
introduces support for the board itself.
All the patches has been tested on Lenovo IdeaPad Duet Chromebook with
the patches applied on top of 5.8-rc1 and with serial console, booting
without problems and being able to go to the login prompt.
Best regards,
Enric
Changes in v2:
- Replace cluster-sleepX for cluster-sleep-x (Matthias Brugger)
- [6/7] Move adding #phy-cells to this patch. (Matthias Brugger)
- [7/7] Move adding #phy-cells out of this patch. (Matthias Brugger)
Enric Balletbo i Serra (7):
dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-krane-sku176
arm64: dts: mt6358: Add the compatible for the regulators
arm64: dts: mt8183: Add MediaTek's peripheral configuration controller
arm64: dts: mt8183: Fix unit name warnings
arm64: dts: mt8183-evb: Fix unit name warnings
arm64: dts: mt8183: Add USB3.0 support
arm64: dts: mt8183: Add krane-sku176 board
.../devicetree/bindings/arm/mediatek.yaml | 5 +
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt6358.dtsi | 2 +
arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 4 +-
.../mediatek/mt8183-kukui-krane-sku176.dts | 18 +
.../boot/dts/mediatek/mt8183-kukui-krane.dtsi | 343 ++++++++
.../arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 788 ++++++++++++++++++
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 68 +-
8 files changed, 1225 insertions(+), 4 deletions(-)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2 1/7] dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-krane-sku176
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
@ 2020-06-25 10:17 ` Enric Balletbo i Serra
2020-06-25 10:17 ` [PATCH v2 2/7] arm64: dts: mt6358: Add the compatible for the regulators Enric Balletbo i Serra
` (6 subsequent siblings)
7 siblings, 0 replies; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Sean Wang, Rob Herring,
Mars Cheng, hsinyi, matthias.bgg, linux-mediatek,
Collabora Kernel ML, linux-arm-kernel
The krane-sku176 is the Lenovo IdeaPad Duet Chromebook. A 2-in-1
detachable device using the MediaTek MT8183 SoC.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---
Changes in v2: None
Documentation/devicetree/bindings/arm/mediatek.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
index abc544dde6920..30908963ae261 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -114,4 +114,9 @@ properties:
- enum:
- mediatek,mt8183-evb
- const: mediatek,mt8183
+ - description: Google Krane (Lenovo IdeaPad Duet, 10e,...)
+ items:
+ - const: google,krane-sku176
+ - const: google,krane
+ - const: mediatek,mt8183
...
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2 2/7] arm64: dts: mt6358: Add the compatible for the regulators
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
2020-06-25 10:17 ` [PATCH v2 1/7] dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-krane-sku176 Enric Balletbo i Serra
@ 2020-06-25 10:17 ` Enric Balletbo i Serra
2020-07-02 5:04 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 3/7] arm64: dts: mt8183: Add MediaTek's peripheral configuration controller Enric Balletbo i Serra
` (5 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Rob Herring, linux-mediatek,
hsinyi, matthias.bgg, Collabora Kernel ML, linux-arm-kernel
The regulators are expected to be instantiated with matching the
device-tree compatible, so add the proper compatible name under the
regulators node.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---
Changes in v2: None
arch/arm64/boot/dts/mediatek/mt6358.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt6358.dtsi b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
index 9361ada0c497e..fa159b20379e4 100644
--- a/arch/arm64/boot/dts/mediatek/mt6358.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
@@ -16,6 +16,8 @@ mt6358codec: mt6358codec {
};
mt6358regulator: mt6358regulator {
+ compatible = "mediatek,mt6358-regulator";
+
mt6358_vdram1_reg: buck_vdram1 {
regulator-name = "vdram1";
regulator-min-microvolt = <500000>;
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2 3/7] arm64: dts: mt8183: Add MediaTek's peripheral configuration controller
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
2020-06-25 10:17 ` [PATCH v2 1/7] dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-krane-sku176 Enric Balletbo i Serra
2020-06-25 10:17 ` [PATCH v2 2/7] arm64: dts: mt6358: Add the compatible for the regulators Enric Balletbo i Serra
@ 2020-06-25 10:17 ` Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 4/7] arm64: dts: mt8183: Fix unit name warnings Enric Balletbo i Serra
` (4 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Rob Herring, linux-mediatek,
hsinyi, matthias.bgg, Collabora Kernel ML, linux-arm-kernel
The MediaTek's peripheral configuration controller is present on the
MT8183 SoC. Add the node for that controller.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---
Changes in v2: None
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index 1e03c849dc5d6..00137ec61164d 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -285,6 +285,12 @@ infracfg: syscon@10001000 {
#reset-cells = <1>;
};
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8183-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
pio: pinctrl@10005000 {
compatible = "mediatek,mt8183-pinctrl";
reg = <0 0x10005000 0 0x1000>,
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2 4/7] arm64: dts: mt8183: Fix unit name warnings
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
` (2 preceding siblings ...)
2020-06-25 10:17 ` [PATCH v2 3/7] arm64: dts: mt8183: Add MediaTek's peripheral configuration controller Enric Balletbo i Serra
@ 2020-06-25 10:17 ` Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 5/7] arm64: dts: mt8183-evb: " Enric Balletbo i Serra
` (3 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Rob Herring, linux-mediatek,
hsinyi, matthias.bgg, Collabora Kernel ML, linux-arm-kernel
Remove the unit address from the DT nodes that doesn't have a reg
property. This fixes the following unit name warnings:
Warning (unit_address_vs_reg): /cpus/idle-states/cluster-sleep@0: node has a unit name, but no reg or ranges property
Warning (unit_address_vs_reg): /cpus/idle-states/cluster-sleep@1: node has a unit name, but no reg or ranges property
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---
Changes in v2:
- Replace cluster-sleepX for cluster-sleep-x (Matthias Brugger)
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index 00137ec61164d..6c00ffa275202 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -168,7 +168,7 @@ CPU_SLEEP: cpu-sleep {
min-residency-us = <800>;
};
- CLUSTER_SLEEP0: cluster-sleep@0 {
+ CLUSTER_SLEEP0: cluster-sleep-0 {
compatible = "arm,idle-state";
local-timer-stop;
arm,psci-suspend-param = <0x01010001>;
@@ -176,7 +176,7 @@ CLUSTER_SLEEP0: cluster-sleep@0 {
exit-latency-us = <400>;
min-residency-us = <1000>;
};
- CLUSTER_SLEEP1: cluster-sleep@1 {
+ CLUSTER_SLEEP1: cluster-sleep-1 {
compatible = "arm,idle-state";
local-timer-stop;
arm,psci-suspend-param = <0x01010001>;
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2 5/7] arm64: dts: mt8183-evb: Fix unit name warnings
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
` (3 preceding siblings ...)
2020-06-25 10:17 ` [PATCH v2 4/7] arm64: dts: mt8183: Fix unit name warnings Enric Balletbo i Serra
@ 2020-06-25 10:17 ` Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 6/7] arm64: dts: mt8183: Add USB3.0 support Enric Balletbo i Serra
` (2 subsequent siblings)
7 siblings, 1 reply; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Rob Herring, linux-mediatek,
hsinyi, matthias.bgg, Collabora Kernel ML, linux-arm-kernel
Remove the unit address from the DT nodes that doesn't have a reg
property. This fixes the following unit name warnings:
Warning (unit_address_vs_reg): /soc/pinctrl@10005000/mmc0@0: node has a unit name, but no reg or ranges property
Warning (unit_address_vs_reg): /soc/pinctrl@10005000/mmc1@0: node has a unit name, but no reg or ranges property
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---
Changes in v2: None
arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
index afd6ddbcbdf2c..ae405bd8f06b0 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
@@ -205,7 +205,7 @@ pins_rst {
};
};
- mmc0_pins_uhs: mmc0@0{
+ mmc0_pins_uhs: mmc0 {
pins_cmd_dat {
pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
<PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
@@ -264,7 +264,7 @@ pins_pmu {
};
};
- mmc1_pins_uhs: mmc1@0{
+ mmc1_pins_uhs: mmc1 {
pins_cmd_dat {
pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
<PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2 6/7] arm64: dts: mt8183: Add USB3.0 support
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
` (4 preceding siblings ...)
2020-06-25 10:17 ` [PATCH v2 5/7] arm64: dts: mt8183-evb: " Enric Balletbo i Serra
@ 2020-06-25 10:17 ` Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 7/7] arm64: dts: mt8183: Add krane-sku176 board Enric Balletbo i Serra
2020-07-10 13:35 ` [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Matthias Brugger
7 siblings, 1 reply; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Rob Herring, linux-mediatek,
hsinyi, matthias.bgg, Collabora Kernel ML, linux-arm-kernel
Add the USB3.0 phyter and controller for the MediaTek's MT8183 SoC.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---
Changes in v2:
- Move adding #phy-cells to this patch. (Matthias Brugger)
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 58 ++++++++++++++++++++++++
1 file changed, 58 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index 6c00ffa275202..102105871db25 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/reset-controller/mt8183-resets.h>
+#include <dt-bindings/phy/phy.h>
#include "mt8183-pinfunc.h"
/ {
@@ -648,6 +649,36 @@ i2c8: i2c@1101b000 {
status = "disabled";
};
+ ssusb: usb@11201000 {
+ compatible ="mediatek,mt8183-mtu3", "mediatek,mtu3";
+ reg = <0 0x11201000 0 0x2e00>,
+ <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u3port0 PHY_TYPE_USB3>;
+ clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>,
+ <&infracfg CLK_INFRA_USB>;
+ clock-names = "sys_ck", "ref_ck";
+ mediatek,syscon-wakeup = <&pericfg 0x400 0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: xhci@11200000 {
+ compatible = "mediatek,mt8183-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>,
+ <&infracfg CLK_INFRA_USB>;
+ clock-names = "sys_ck", "ref_ck";
+ status = "disabled";
+ };
+ };
+
audiosys: syscon@11220000 {
compatible = "mediatek,mt8183-audiosys", "syscon";
reg = <0 0x11220000 0 0x1000>;
@@ -684,6 +715,33 @@ efuse: efuse@11f10000 {
reg = <0 0x11f10000 0 0x1000>;
};
+ u3phy: usb-phy@11f40000 {
+ compatible = "mediatek,mt8183-tphy",
+ "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #phy-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11f40000 0x1000>;
+ status = "okay";
+
+ u2port0: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ mediatek,discth = <15>;
+ status = "okay";
+ };
+
+ u3port0: usb-phy@0700 {
+ reg = <0x0700 0x900>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+ };
+
mfgcfg: syscon@13000000 {
compatible = "mediatek,mt8183-mfgcfg", "syscon";
reg = <0 0x13000000 0 0x1000>;
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v2 7/7] arm64: dts: mt8183: Add krane-sku176 board
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
` (5 preceding siblings ...)
2020-06-25 10:17 ` [PATCH v2 6/7] arm64: dts: mt8183: Add USB3.0 support Enric Balletbo i Serra
@ 2020-06-25 10:17 ` Enric Balletbo i Serra
2020-07-02 5:07 ` Hsin-Yi Wang
2020-07-10 13:35 ` [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Matthias Brugger
7 siblings, 1 reply; 15+ messages in thread
From: Enric Balletbo i Serra @ 2020-06-25 10:17 UTC (permalink / raw)
To: linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Ben Ho, Rob Herring,
linux-mediatek, hsinyi, matthias.bgg, Collabora Kernel ML,
linux-arm-kernel
Also known as the Lenovo IdeaPad Duet Chromebook.
There are different krane boards with shared resources, hence a
mt8183-kukui-krane.dtsi was created for easily introduce future new
boards. The same happens with the baseboard codenamed kukui where
different variants, apart from kukui variant can take advantage of the
shared resources.
Signed-off-by: Ben Ho <Ben.Ho@mediatek.com>
[originally created by Ben Ho but adapted and ported to mainline]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---
Changes in v2:
- Move adding #phy-cells out of this patch. (Matthias Brugger)
arch/arm64/boot/dts/mediatek/Makefile | 1 +
.../mediatek/mt8183-kukui-krane-sku176.dts | 18 +
.../boot/dts/mediatek/mt8183-kukui-krane.dtsi | 343 ++++++++
.../arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 788 ++++++++++++++++++
4 files changed, 1150 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 848218f55bc1d..708fc60fa589a 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -12,4 +12,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
new file mode 100644
index 0000000000000..47113e275cb52
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2019 Google LLC
+ *
+ * Device-tree for Krane sku176.
+ *
+ * SKU is a 8-bit value (0xb0 == 176):
+ * - Bits 7..4: Panel ID: 0xb (BOE)
+ * - Bits 3..0: SKU ID: 0x0 (default)
+ */
+
+/dts-v1/;
+#include "mt8183-kukui-krane.dtsi"
+
+/ {
+ model = "MediaTek krane sku176 board";
+ compatible = "google,krane-sku176", "google,krane", "mediatek,mt8183";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
new file mode 100644
index 0000000000000..fbc471ccf805f
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2019 Google LLC
+ */
+
+#include "mt8183-kukui.dtsi"
+
+/ {
+ ppvarn_lcd: ppvarn-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvarn_lcd";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ppvarn_lcd_en>;
+
+ enable-active-high;
+
+ gpio = <&pio 66 GPIO_ACTIVE_HIGH>;
+ };
+
+ ppvarp_lcd: ppvarp-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvarp_lcd";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ppvarp_lcd_en>;
+
+ enable-active-high;
+
+ gpio = <&pio 166 GPIO_ACTIVE_HIGH>;
+ };
+
+ pp1800_lcd: pp1800-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1800_lcd";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pp1800_lcd_en>;
+
+ enable-active-high;
+
+ gpio = <&pio 36 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&bluetooth {
+ firmware-name = "nvm_00440302_i2s_eu.bin";
+};
+
+&i2c0 {
+ status = "okay";
+
+ touchscreen4: touchscreen@5d {
+ compatible = "hid-over-i2c";
+ reg = <0x5d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&open_touch>;
+
+ interrupt-parent = <&pio>;
+ interrupts = <155 IRQ_TYPE_EDGE_FALLING>;
+
+ post-power-on-delay-ms = <10>;
+ hid-descr-addr = <0x0001>;
+ };
+};
+
+&mt6358_vcama2_reg {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom@58 {
+ compatible = "atmel,24c32";
+ reg = <0x58>;
+ pagesize = <32>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom@54 {
+ compatible = "atmel,24c32";
+ reg = <0x54>;
+ pagesize = <32>;
+ };
+};
+
+&pio {
+ /* 192 lines */
+ gpio-line-names =
+ "SPI_AP_EC_CS_L",
+ "SPI_AP_EC_MOSI",
+ "SPI_AP_EC_CLK",
+ "I2S3_DO",
+ "USB_PD_INT_ODL",
+ "",
+ "",
+ "",
+ "",
+ "IT6505_HPD_L",
+ "I2S3_TDM_D3",
+ "SOC_I2C6_1V8_SCL",
+ "SOC_I2C6_1V8_SDA",
+ "DPI_D0",
+ "DPI_D1",
+ "DPI_D2",
+ "DPI_D3",
+ "DPI_D4",
+ "DPI_D5",
+ "DPI_D6",
+ "DPI_D7",
+ "DPI_D8",
+ "DPI_D9",
+ "DPI_D10",
+ "DPI_D11",
+ "DPI_HSYNC",
+ "DPI_VSYNC",
+ "DPI_DE",
+ "DPI_CK",
+ "AP_MSDC1_CLK",
+ "AP_MSDC1_DAT3",
+ "AP_MSDC1_CMD",
+ "AP_MSDC1_DAT0",
+ "AP_MSDC1_DAT2",
+ "AP_MSDC1_DAT1",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "OTG_EN",
+ "DRVBUS",
+ "DISP_PWM",
+ "DSI_TE",
+ "LCM_RST_1V8",
+ "AP_CTS_WIFI_RTS",
+ "AP_RTS_WIFI_CTS",
+ "SOC_I2C5_1V8_SCL",
+ "SOC_I2C5_1V8_SDA",
+ "SOC_I2C3_1V8_SCL",
+ "SOC_I2C3_1V8_SDA",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "SOC_I2C1_1V8_SDA",
+ "SOC_I2C0_1V8_SDA",
+ "SOC_I2C0_1V8_SCL",
+ "SOC_I2C1_1V8_SCL",
+ "AP_SPI_H1_MISO",
+ "AP_SPI_H1_CS_L",
+ "AP_SPI_H1_MOSI",
+ "AP_SPI_H1_CLK",
+ "I2S5_BCK",
+ "I2S5_LRCK",
+ "I2S5_DO",
+ "BOOTBLOCK_EN_L",
+ "MT8183_KPCOL0",
+ "SPI_AP_EC_MISO",
+ "UART_DBG_TX_AP_RX",
+ "UART_AP_TX_DBG_RX",
+ "I2S2_MCK",
+ "I2S2_BCK",
+ "CLK_5M_WCAM",
+ "CLK_2M_UCAM",
+ "I2S2_LRCK",
+ "I2S2_DI",
+ "SOC_I2C2_1V8_SCL",
+ "SOC_I2C2_1V8_SDA",
+ "SOC_I2C4_1V8_SCL",
+ "SOC_I2C4_1V8_SDA",
+ "",
+ "SCL8",
+ "SDA8",
+ "FCAM_PWDN_L",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "I2S_PMIC",
+ "I2S_PMIC",
+ "I2S_PMIC",
+ "I2S_PMIC",
+ "I2S_PMIC",
+ "I2S_PMIC",
+ "I2S_PMIC",
+ "I2S_PMIC",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ /*
+ * AP_FLASH_WP_L is crossystem ABI. Rev1 schematics
+ * call it BIOS_FLASH_WP_R_L.
+ */
+ "AP_FLASH_WP_L",
+ "EC_AP_INT_ODL",
+ "IT6505_INT_ODL",
+ "H1_INT_OD_L",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "AP_SPI_FLASH_MISO",
+ "AP_SPI_FLASH_CS_L",
+ "AP_SPI_FLASH_MOSI",
+ "AP_SPI_FLASH_CLK",
+ "DA7219_IRQ",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "";
+
+ ppvarp_lcd_en: ppvarp-lcd-en {
+ pins1 {
+ pinmux = <PINMUX_GPIO66__FUNC_GPIO66>;
+ output-low;
+ };
+ };
+
+ ppvarn_lcd_en: ppvarn-lcd-en {
+ pins1 {
+ pinmux = <PINMUX_GPIO166__FUNC_GPIO166>;
+ output-low;
+ };
+ };
+
+ pp1800_lcd_en: pp1800-lcd-en {
+ pins1 {
+ pinmux = <PINMUX_GPIO36__FUNC_GPIO36>;
+ output-low;
+ };
+ };
+
+ open_touch: open_touch {
+ irq_pin {
+ pinmux = <PINMUX_GPIO155__FUNC_GPIO155>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ rst_pin {
+ pinmux = <PINMUX_GPIO156__FUNC_GPIO156>;
+
+ /*
+ * The pen driver doesn't currently support driving
+ * this reset line. By specifying output-high here
+ * we're relying on the fact that this pin has a default
+ * pulldown at boot (which makes sure the pen was in
+ * reset if it was powered) and then we set it high here
+ * to take it out of reset. Better would be if the pen
+ * driver could control this and we could remove
+ * "output-high" here.
+ */
+ output-high;
+ };
+ };
+};
+
+&qca_wifi {
+ qcom,ath10k-calibration-variant = "LE_Krane";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
new file mode 100644
index 0000000000000..f0a070535b340
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
@@ -0,0 +1,788 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (c) 2018 MediaTek Inc.
+ * Author: Ben Ho <ben.ho@mediatek.com>
+ * Erin Lo <erin.lo@mediatek.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "mt8183.dtsi"
+#include "mt6358.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x80000000>;
+ };
+
+ clk32k: oscillator1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "clk32k";
+ };
+
+ it6505_pp18_reg: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "it6505_pp18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&pio 178 0>;
+ enable-active-high;
+ };
+
+ lcd_pp3300: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_pp3300";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ bl_pp5000: regulator2 {
+ compatible = "regulator-fixed";
+ regulator-name = "bl_pp5000";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ mmc1_fixed_power: regulator3 {
+ compatible = "regulator-fixed";
+ regulator-name = "mmc1_power";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ mmc1_fixed_io: regulator4 {
+ compatible = "regulator-fixed";
+ regulator-name = "mmc1_io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pp1800_alw: regulator5 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1800_alw";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pp3300_alw: regulator6 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_alw";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ max98357a: codec0 {
+ compatible = "maxim,max98357a";
+ sdmode-gpios = <&pio 175 0>;
+ };
+
+ btsco: codec1 {
+ compatible = "linux,bt-sco";
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pins_pwrseq>;
+
+ /* Toggle WIFI_ENABLE to reset the chip. */
+ reset-gpios = <&pio 119 1>;
+ };
+
+ wifi_wakeup: wifi-wakeup {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pins_wakeup>;
+
+ wowlan {
+ label = "Wake on WiFi";
+ gpios = <&pio 113 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+ };
+
+ tboard_thermistor1: thermal-sensor1 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&auxadc 0>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-5000) 4241
+ 0 4063
+ 5000 3856
+ 10000 3621
+ 15000 3364
+ 20000 3091
+ 25000 2810
+ 30000 2526
+ 35000 2247
+ 40000 1982
+ 45000 1734
+ 50000 1507
+ 55000 1305
+ 60000 1122
+ 65000 964
+ 70000 827
+ 75000 710
+ 80000 606
+ 85000 519
+ 90000 445
+ 95000 382
+ 100000 330
+ 105000 284
+ 110000 245
+ 115000 213
+ 120000 183
+ 125000 161>;
+ };
+
+ tboard_thermistor2: thermal-sensor2 {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&auxadc 1>;
+ io-channel-names = "sensor-channel";
+ temperature-lookup-table = < (-5000) 4241
+ 0 4063
+ 5000 3856
+ 10000 3621
+ 15000 3364
+ 20000 3091
+ 25000 2810
+ 30000 2526
+ 35000 2247
+ 40000 1982
+ 45000 1734
+ 50000 1507
+ 55000 1305
+ 60000 1122
+ 65000 964
+ 70000 827
+ 75000 710
+ 80000 606
+ 85000 519
+ 90000 445
+ 95000 382
+ 100000 330
+ 105000 284
+ 110000 245
+ 115000 213
+ 120000 183
+ 125000 161>;
+ };
+};
+
+&auxadc {
+ status = "okay";
+};
+
+&cpu0 {
+ proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu1 {
+ proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu2 {
+ proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu3 {
+ proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu4 {
+ proc-supply = <&mt6358_vproc11_reg>;
+};
+
+&cpu5 {
+ proc-supply = <&mt6358_vproc11_reg>;
+};
+
+&cpu6 {
+ proc-supply = <&mt6358_vproc11_reg>;
+};
+
+&cpu7 {
+ proc-supply = <&mt6358_vproc11_reg>;
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+ clock-frequency = <400000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
+
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
+
+&i2c6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&mmc0 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ cap-mmc-hw-reset;
+ no-sdio;
+ no-sd;
+ hs400-ds-delay = <0x12814>;
+ vmmc-supply = <&mt6358_vemc_reg>;
+ vqmmc-supply = <&mt6358_vio18_reg>;
+ assigned-clocks = <&topckgen CLK_TOP_MUX_MSDC50_0>;
+ assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_CK>;
+ non-removable;
+};
+
+&mmc1 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_uhs>;
+ vmmc-supply = <&mmc1_fixed_power>;
+ vqmmc-supply = <&mmc1_fixed_io>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ max-frequency = <200000000>;
+ drv-type = <2>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ cap-sdio-irq;
+ non-removable;
+ no-mmc;
+ no-sd;
+ assigned-clocks = <&topckgen CLK_TOP_MUX_MSDC30_1>;
+ assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qca_wifi: qca-wifi@1 {
+ compatible = "qcom,ath10k";
+ reg = <1>;
+ };
+};
+
+&mt6358_vdram2_reg {
+ regulator-always-on;
+};
+
+&mt6358codec {
+ Avdd-supply = <&mt6358_vaud28_reg>;
+};
+
+&mt6358_vsim1_reg {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+};
+
+&mt6358_vsim2_reg {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+};
+
+&pio {
+ bt_pins: bt-pins {
+ pins_bt_en {
+ pinmux = <PINMUX_GPIO120__FUNC_GPIO120>;
+ output-low;
+ };
+ };
+
+ ec_ap_int_odl: ec_ap_int_odl {
+ pins1 {
+ pinmux = <PINMUX_GPIO151__FUNC_GPIO151>;
+ input-enable;
+ bias-pull-up;
+ };
+ };
+
+ h1_int_od_l: h1_int_od_l {
+ pins1 {
+ pinmux = <PINMUX_GPIO153__FUNC_GPIO153>;
+ input-enable;
+ };
+ };
+
+ i2c0_pins: i2c0 {
+ pins_bus {
+ pinmux = <PINMUX_GPIO82__FUNC_SDA0>,
+ <PINMUX_GPIO83__FUNC_SCL0>;
+ mediatek,pull-up-adv = <3>;
+ mediatek,drive-strength-adv = <00>;
+ };
+ };
+
+ i2c1_pins: i2c1 {
+ pins_bus {
+ pinmux = <PINMUX_GPIO81__FUNC_SDA1>,
+ <PINMUX_GPIO84__FUNC_SCL1>;
+ mediatek,pull-up-adv = <3>;
+ mediatek,drive-strength-adv = <00>;
+ };
+ };
+
+ i2c2_pins: i2c2 {
+ pins_bus {
+ pinmux = <PINMUX_GPIO103__FUNC_SCL2>,
+ <PINMUX_GPIO104__FUNC_SDA2>;
+ bias-disable;
+ mediatek,drive-strength-adv = <00>;
+ };
+ };
+
+ i2c3_pins: i2c3 {
+ pins_bus {
+ pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
+ <PINMUX_GPIO51__FUNC_SDA3>;
+ mediatek,pull-up-adv = <3>;
+ mediatek,drive-strength-adv = <00>;
+ };
+ };
+
+ i2c4_pins: i2c4 {
+ pins_bus {
+ pinmux = <PINMUX_GPIO105__FUNC_SCL4>,
+ <PINMUX_GPIO106__FUNC_SDA4>;
+ bias-disable;
+ mediatek,drive-strength-adv = <00>;
+ };
+ };
+
+ i2c5_pins: i2c5 {
+ pins_bus {
+ pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
+ <PINMUX_GPIO49__FUNC_SDA5>;
+ mediatek,pull-up-adv = <3>;
+ mediatek,drive-strength-adv = <00>;
+ };
+ };
+
+ i2c6_pins: i2c6 {
+ pins_bus {
+ pinmux = <PINMUX_GPIO11__FUNC_SCL6>,
+ <PINMUX_GPIO12__FUNC_SDA6>;
+ bias-disable;
+ };
+ };
+
+ mmc0_pins_default: mmc0-pins-default {
+ pins_cmd_dat {
+ pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
+ <PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
+ <PINMUX_GPIO125__FUNC_MSDC0_DAT2>,
+ <PINMUX_GPIO132__FUNC_MSDC0_DAT3>,
+ <PINMUX_GPIO126__FUNC_MSDC0_DAT4>,
+ <PINMUX_GPIO129__FUNC_MSDC0_DAT5>,
+ <PINMUX_GPIO127__FUNC_MSDC0_DAT6>,
+ <PINMUX_GPIO130__FUNC_MSDC0_DAT7>,
+ <PINMUX_GPIO122__FUNC_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_14mA>;
+ mediatek,pull-up-adv = <01>;
+ };
+
+ pins_clk {
+ pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_14mA>;
+ mediatek,pull-down-adv = <10>;
+ };
+
+ pins_rst {
+ pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
+ drive-strength = <MTK_DRIVE_14mA>;
+ mediatek,pull-down-adv = <01>;
+ };
+ };
+
+ mmc0_pins_uhs: mmc0-pins-uhs {
+ pins_cmd_dat {
+ pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
+ <PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
+ <PINMUX_GPIO125__FUNC_MSDC0_DAT2>,
+ <PINMUX_GPIO132__FUNC_MSDC0_DAT3>,
+ <PINMUX_GPIO126__FUNC_MSDC0_DAT4>,
+ <PINMUX_GPIO129__FUNC_MSDC0_DAT5>,
+ <PINMUX_GPIO127__FUNC_MSDC0_DAT6>,
+ <PINMUX_GPIO130__FUNC_MSDC0_DAT7>,
+ <PINMUX_GPIO122__FUNC_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_14mA>;
+ mediatek,pull-up-adv = <01>;
+ };
+
+ pins_clk {
+ pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_14mA>;
+ mediatek,pull-down-adv = <10>;
+ };
+
+ pins_ds {
+ pinmux = <PINMUX_GPIO131__FUNC_MSDC0_DSL>;
+ drive-strength = <MTK_DRIVE_14mA>;
+ mediatek,pull-down-adv = <10>;
+ };
+
+ pins_rst {
+ pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
+ drive-strength = <MTK_DRIVE_14mA>;
+ mediatek,pull-up-adv = <01>;
+ };
+ };
+
+ mmc1_pins_default: mmc1-pins-default {
+ pins_cmd_dat {
+ pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
+ <PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
+ <PINMUX_GPIO34__FUNC_MSDC1_DAT1>,
+ <PINMUX_GPIO33__FUNC_MSDC1_DAT2>,
+ <PINMUX_GPIO30__FUNC_MSDC1_DAT3>;
+ input-enable;
+ mediatek,pull-up-adv = <10>;
+ };
+
+ pins_clk {
+ pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
+ input-enable;
+ mediatek,pull-down-adv = <10>;
+ };
+ };
+
+ mmc1_pins_uhs: mmc1-pins-uhs {
+ pins_cmd_dat {
+ pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
+ <PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
+ <PINMUX_GPIO34__FUNC_MSDC1_DAT1>,
+ <PINMUX_GPIO33__FUNC_MSDC1_DAT2>,
+ <PINMUX_GPIO30__FUNC_MSDC1_DAT3>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ input-enable;
+ mediatek,pull-up-adv = <10>;
+ };
+
+ pins_clk {
+ pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ mediatek,pull-down-adv = <10>;
+ input-enable;
+ };
+ };
+
+ spi0_pins: spi0 {
+ pins_spi{
+ pinmux = <PINMUX_GPIO85__FUNC_SPI0_MI>,
+ <PINMUX_GPIO86__FUNC_GPIO86>,
+ <PINMUX_GPIO87__FUNC_SPI0_MO>,
+ <PINMUX_GPIO88__FUNC_SPI0_CLK>;
+ bias-disable;
+ };
+ };
+
+ spi1_pins: spi1 {
+ pins_spi{
+ pinmux = <PINMUX_GPIO161__FUNC_SPI1_A_MI>,
+ <PINMUX_GPIO162__FUNC_SPI1_A_CSB>,
+ <PINMUX_GPIO163__FUNC_SPI1_A_MO>,
+ <PINMUX_GPIO164__FUNC_SPI1_A_CLK>;
+ bias-disable;
+ };
+ };
+
+ spi2_pins: spi2 {
+ pins_spi{
+ pinmux = <PINMUX_GPIO0__FUNC_SPI2_CSB>,
+ <PINMUX_GPIO1__FUNC_SPI2_MO>,
+ <PINMUX_GPIO2__FUNC_SPI2_CLK>;
+ bias-disable;
+ };
+ pins_spi_mi {
+ pinmux = <PINMUX_GPIO94__FUNC_SPI2_MI>;
+ mediatek,pull-down-adv = <00>;
+ };
+ };
+
+ spi3_pins: spi3 {
+ pins_spi{
+ pinmux = <PINMUX_GPIO21__FUNC_SPI3_MI>,
+ <PINMUX_GPIO22__FUNC_SPI3_CSB>,
+ <PINMUX_GPIO23__FUNC_SPI3_MO>,
+ <PINMUX_GPIO24__FUNC_SPI3_CLK>;
+ bias-disable;
+ };
+ };
+
+ spi4_pins: spi4 {
+ pins_spi{
+ pinmux = <PINMUX_GPIO17__FUNC_SPI4_MI>,
+ <PINMUX_GPIO18__FUNC_SPI4_CSB>,
+ <PINMUX_GPIO19__FUNC_SPI4_MO>,
+ <PINMUX_GPIO20__FUNC_SPI4_CLK>;
+ bias-disable;
+ };
+ };
+
+ spi5_pins: spi5 {
+ pins_spi{
+ pinmux = <PINMUX_GPIO13__FUNC_SPI5_MI>,
+ <PINMUX_GPIO14__FUNC_SPI5_CSB>,
+ <PINMUX_GPIO15__FUNC_SPI5_MO>,
+ <PINMUX_GPIO16__FUNC_SPI5_CLK>;
+ bias-disable;
+ };
+ };
+
+ uart0_pins_default: uart0-pins-default {
+ pins_rx {
+ pinmux = <PINMUX_GPIO95__FUNC_URXD0>;
+ input-enable;
+ bias-pull-up;
+ };
+ pins_tx {
+ pinmux = <PINMUX_GPIO96__FUNC_UTXD0>;
+ };
+ };
+
+ uart1_pins_default: uart1-pins-default {
+ pins_rx {
+ pinmux = <PINMUX_GPIO121__FUNC_URXD1>;
+ input-enable;
+ bias-pull-up;
+ };
+ pins_tx {
+ pinmux = <PINMUX_GPIO115__FUNC_UTXD1>;
+ };
+ pins_rts {
+ pinmux = <PINMUX_GPIO47__FUNC_URTS1>;
+ output-enable;
+ };
+ pins_cts {
+ pinmux = <PINMUX_GPIO46__FUNC_UCTS1>;
+ input-enable;
+ };
+ };
+
+ uart1_pins_sleep: uart1-pins-sleep {
+ pins_rx {
+ pinmux = <PINMUX_GPIO121__FUNC_GPIO121>;
+ input-enable;
+ bias-pull-up;
+ };
+ pins_tx {
+ pinmux = <PINMUX_GPIO115__FUNC_UTXD1>;
+ };
+ pins_rts {
+ pinmux = <PINMUX_GPIO47__FUNC_URTS1>;
+ output-enable;
+ };
+ pins_cts {
+ pinmux = <PINMUX_GPIO46__FUNC_UCTS1>;
+ input-enable;
+ };
+ };
+
+ wifi_pins_pwrseq: wifi-pins-pwrseq {
+ pins_wifi_enable {
+ pinmux = <PINMUX_GPIO119__FUNC_GPIO119>;
+ output-low;
+ };
+ };
+
+ wifi_pins_wakeup: wifi-pins-wakeup {
+ pins_wifi_wakeup {
+ pinmux = <PINMUX_GPIO113__FUNC_GPIO113>;
+ input-enable;
+ };
+ };
+};
+
+&soc_data {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ mediatek,pad-select = <0>;
+ status = "okay";
+ cs-gpios = <&pio 86 GPIO_ACTIVE_LOW>;
+
+ cr50@0 {
+ compatible = "google,cr50";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&h1_int_od_l>;
+ interrupt-parent = <&pio>;
+ interrupts = <153 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ mediatek,pad-select = <0>;
+ status = "okay";
+
+ w25q64dw: spi-flash@0 {
+ compatible = "winbond,w25q64dw", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+ };
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins>;
+ mediatek,pad-select = <0>;
+ status = "okay";
+
+ cros_ec: cros-ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0>;
+ spi-max-frequency = <3000000>;
+ interrupt-parent = <&pio>;
+ interrupts = <151 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_ap_int_odl>;
+
+ i2c_tunnel: i2c-tunnel {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbc_extcon: extcon0 {
+ compatible = "google,extcon-usbc-cros-ec";
+ google,usb-port-id = <0>;
+ };
+ };
+};
+
+&spi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pins>;
+ mediatek,pad-select = <0>;
+ status = "disabled";
+};
+
+&spi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi4_pins>;
+ mediatek,pad-select = <0>;
+ status = "disabled";
+};
+
+&spi5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi5_pins>;
+ mediatek,pad-select = <0>;
+ status = "disabled";
+};
+
+&ssusb {
+ dr_mode = "host";
+ wakeup-source;
+ vusb33-supply = <&mt6358_vusb_reg>;
+ status = "okay";
+};
+
+&u3phy {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_default>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_pins_default>;
+ pinctrl-1 = <&uart1_pins_sleep>;
+ status = "okay";
+ interrupts-extended = <&sysirq GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>,
+ <&pio 121 IRQ_TYPE_EDGE_FALLING>;
+
+ bluetooth: bluetooth {
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_pins>;
+ status = "okay";
+ compatible = "qcom,qca6174-bt";
+ enable-gpios = <&pio 120 0>;
+ clocks = <&clk32k>;
+ firmware-name = "nvm_00440302_i2s.bin";
+ };
+};
+
+&usb_host {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ vusb33-supply = <&mt6358_vusb_reg>;
+ status = "okay";
+
+ hub@1 {
+ compatible = "usb5e3,610";
+ reg = <1>;
+ };
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
--
2.27.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v2 2/7] arm64: dts: mt6358: Add the compatible for the regulators
2020-06-25 10:17 ` [PATCH v2 2/7] arm64: dts: mt6358: Add the compatible for the regulators Enric Balletbo i Serra
@ 2020-07-02 5:04 ` Hsin-Yi Wang
0 siblings, 0 replies; 15+ messages in thread
From: Hsin-Yi Wang @ 2020-07-02 5:04 UTC (permalink / raw)
To: Enric Balletbo i Serra
Cc: erwanaliasr1, Nicolas Boichat, Devicetree List, lkml,
Rob Herring, moderated list:ARM/Mediatek SoC support,
Matthias Brugger, Collabora Kernel ML,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Thu, Jun 25, 2020 at 6:18 PM Enric Balletbo i Serra
<enric.balletbo@collabora.com> wrote:
>
> The regulators are expected to be instantiated with matching the
> device-tree compatible, so add the proper compatible name under the
> regulators node.
>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/arm64/boot/dts/mediatek/mt6358.dtsi | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt6358.dtsi b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
> index 9361ada0c497e..fa159b20379e4 100644
> --- a/arch/arm64/boot/dts/mediatek/mt6358.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
> @@ -16,6 +16,8 @@ mt6358codec: mt6358codec {
> };
>
> mt6358regulator: mt6358regulator {
> + compatible = "mediatek,mt6358-regulator";
> +
> mt6358_vdram1_reg: buck_vdram1 {
> regulator-name = "vdram1";
> regulator-min-microvolt = <500000>;
> --
> 2.27.0
>
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2 3/7] arm64: dts: mt8183: Add MediaTek's peripheral configuration controller
2020-06-25 10:17 ` [PATCH v2 3/7] arm64: dts: mt8183: Add MediaTek's peripheral configuration controller Enric Balletbo i Serra
@ 2020-07-02 5:06 ` Hsin-Yi Wang
0 siblings, 0 replies; 15+ messages in thread
From: Hsin-Yi Wang @ 2020-07-02 5:06 UTC (permalink / raw)
To: Enric Balletbo i Serra
Cc: erwanaliasr1, Nicolas Boichat, Devicetree List, lkml,
Rob Herring, moderated list:ARM/Mediatek SoC support,
Matthias Brugger, Collabora Kernel ML,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Thu, Jun 25, 2020 at 6:18 PM Enric Balletbo i Serra
<enric.balletbo@collabora.com> wrote:
>
> The MediaTek's peripheral configuration controller is present on the
> MT8183 SoC. Add the node for that controller.
>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/arm64/boot/dts/mediatek/mt8183.dtsi | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> index 1e03c849dc5d6..00137ec61164d 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> @@ -285,6 +285,12 @@ infracfg: syscon@10001000 {
> #reset-cells = <1>;
> };
>
> + pericfg: syscon@10003000 {
> + compatible = "mediatek,mt8183-pericfg", "syscon";
> + reg = <0 0x10003000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> pio: pinctrl@10005000 {
> compatible = "mediatek,mt8183-pinctrl";
> reg = <0 0x10005000 0 0x1000>,
> --
> 2.27.0
>
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2 4/7] arm64: dts: mt8183: Fix unit name warnings
2020-06-25 10:17 ` [PATCH v2 4/7] arm64: dts: mt8183: Fix unit name warnings Enric Balletbo i Serra
@ 2020-07-02 5:06 ` Hsin-Yi Wang
0 siblings, 0 replies; 15+ messages in thread
From: Hsin-Yi Wang @ 2020-07-02 5:06 UTC (permalink / raw)
To: Enric Balletbo i Serra
Cc: erwanaliasr1, Nicolas Boichat, Devicetree List, lkml,
Rob Herring, moderated list:ARM/Mediatek SoC support,
Matthias Brugger, Collabora Kernel ML,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Thu, Jun 25, 2020 at 6:18 PM Enric Balletbo i Serra
<enric.balletbo@collabora.com> wrote:
>
> Remove the unit address from the DT nodes that doesn't have a reg
> property. This fixes the following unit name warnings:
>
> Warning (unit_address_vs_reg): /cpus/idle-states/cluster-sleep@0: node has a unit name, but no reg or ranges property
> Warning (unit_address_vs_reg): /cpus/idle-states/cluster-sleep@1: node has a unit name, but no reg or ranges property
>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
>
> Changes in v2:
> - Replace cluster-sleepX for cluster-sleep-x (Matthias Brugger)
>
> arch/arm64/boot/dts/mediatek/mt8183.dtsi | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> index 00137ec61164d..6c00ffa275202 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> @@ -168,7 +168,7 @@ CPU_SLEEP: cpu-sleep {
> min-residency-us = <800>;
> };
>
> - CLUSTER_SLEEP0: cluster-sleep@0 {
> + CLUSTER_SLEEP0: cluster-sleep-0 {
> compatible = "arm,idle-state";
> local-timer-stop;
> arm,psci-suspend-param = <0x01010001>;
> @@ -176,7 +176,7 @@ CLUSTER_SLEEP0: cluster-sleep@0 {
> exit-latency-us = <400>;
> min-residency-us = <1000>;
> };
> - CLUSTER_SLEEP1: cluster-sleep@1 {
> + CLUSTER_SLEEP1: cluster-sleep-1 {
> compatible = "arm,idle-state";
> local-timer-stop;
> arm,psci-suspend-param = <0x01010001>;
> --
> 2.27.0
>
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2 5/7] arm64: dts: mt8183-evb: Fix unit name warnings
2020-06-25 10:17 ` [PATCH v2 5/7] arm64: dts: mt8183-evb: " Enric Balletbo i Serra
@ 2020-07-02 5:06 ` Hsin-Yi Wang
0 siblings, 0 replies; 15+ messages in thread
From: Hsin-Yi Wang @ 2020-07-02 5:06 UTC (permalink / raw)
To: Enric Balletbo i Serra
Cc: erwanaliasr1, Nicolas Boichat, Devicetree List, lkml,
Rob Herring, moderated list:ARM/Mediatek SoC support,
Matthias Brugger, Collabora Kernel ML,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Thu, Jun 25, 2020 at 6:18 PM Enric Balletbo i Serra
<enric.balletbo@collabora.com> wrote:
>
> Remove the unit address from the DT nodes that doesn't have a reg
> property. This fixes the following unit name warnings:
>
> Warning (unit_address_vs_reg): /soc/pinctrl@10005000/mmc0@0: node has a unit name, but no reg or ranges property
> Warning (unit_address_vs_reg): /soc/pinctrl@10005000/mmc1@0: node has a unit name, but no reg or ranges property
>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
>
> Changes in v2: None
>
> arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
> index afd6ddbcbdf2c..ae405bd8f06b0 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
> @@ -205,7 +205,7 @@ pins_rst {
> };
> };
>
> - mmc0_pins_uhs: mmc0@0{
> + mmc0_pins_uhs: mmc0 {
> pins_cmd_dat {
> pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
> <PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
> @@ -264,7 +264,7 @@ pins_pmu {
> };
> };
>
> - mmc1_pins_uhs: mmc1@0{
> + mmc1_pins_uhs: mmc1 {
> pins_cmd_dat {
> pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
> <PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
> --
> 2.27.0
>
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2 6/7] arm64: dts: mt8183: Add USB3.0 support
2020-06-25 10:17 ` [PATCH v2 6/7] arm64: dts: mt8183: Add USB3.0 support Enric Balletbo i Serra
@ 2020-07-02 5:06 ` Hsin-Yi Wang
0 siblings, 0 replies; 15+ messages in thread
From: Hsin-Yi Wang @ 2020-07-02 5:06 UTC (permalink / raw)
To: Enric Balletbo i Serra
Cc: erwanaliasr1, Nicolas Boichat, Devicetree List, lkml,
Rob Herring, moderated list:ARM/Mediatek SoC support,
Matthias Brugger, Collabora Kernel ML,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Thu, Jun 25, 2020 at 6:18 PM Enric Balletbo i Serra
<enric.balletbo@collabora.com> wrote:
>
> Add the USB3.0 phyter and controller for the MediaTek's MT8183 SoC.
>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
>
> Changes in v2:
> - Move adding #phy-cells to this patch. (Matthias Brugger)
>
> arch/arm64/boot/dts/mediatek/mt8183.dtsi | 58 ++++++++++++++++++++++++
> 1 file changed, 58 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> index 6c00ffa275202..102105871db25 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
> @@ -9,6 +9,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/reset-controller/mt8183-resets.h>
> +#include <dt-bindings/phy/phy.h>
> #include "mt8183-pinfunc.h"
>
> / {
> @@ -648,6 +649,36 @@ i2c8: i2c@1101b000 {
> status = "disabled";
> };
>
> + ssusb: usb@11201000 {
> + compatible ="mediatek,mt8183-mtu3", "mediatek,mtu3";
> + reg = <0 0x11201000 0 0x2e00>,
> + <0 0x11203e00 0 0x0100>;
> + reg-names = "mac", "ippc";
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
> + phys = <&u2port0 PHY_TYPE_USB2>,
> + <&u3port0 PHY_TYPE_USB3>;
> + clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>,
> + <&infracfg CLK_INFRA_USB>;
> + clock-names = "sys_ck", "ref_ck";
> + mediatek,syscon-wakeup = <&pericfg 0x400 0>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + status = "disabled";
> +
> + usb_host: xhci@11200000 {
> + compatible = "mediatek,mt8183-xhci",
> + "mediatek,mtk-xhci";
> + reg = <0 0x11200000 0 0x1000>;
> + reg-names = "mac";
> + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>,
> + <&infracfg CLK_INFRA_USB>;
> + clock-names = "sys_ck", "ref_ck";
> + status = "disabled";
> + };
> + };
> +
> audiosys: syscon@11220000 {
> compatible = "mediatek,mt8183-audiosys", "syscon";
> reg = <0 0x11220000 0 0x1000>;
> @@ -684,6 +715,33 @@ efuse: efuse@11f10000 {
> reg = <0 0x11f10000 0 0x1000>;
> };
>
> + u3phy: usb-phy@11f40000 {
> + compatible = "mediatek,mt8183-tphy",
> + "mediatek,generic-tphy-v2";
> + #address-cells = <1>;
> + #phy-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0 0x11f40000 0x1000>;
> + status = "okay";
> +
> + u2port0: usb-phy@0 {
> + reg = <0x0 0x700>;
> + clocks = <&clk26m>;
> + clock-names = "ref";
> + #phy-cells = <1>;
> + mediatek,discth = <15>;
> + status = "okay";
> + };
> +
> + u3port0: usb-phy@0700 {
> + reg = <0x0700 0x900>;
> + clocks = <&clk26m>;
> + clock-names = "ref";
> + #phy-cells = <1>;
> + status = "okay";
> + };
> + };
> +
> mfgcfg: syscon@13000000 {
> compatible = "mediatek,mt8183-mfgcfg", "syscon";
> reg = <0 0x13000000 0 0x1000>;
> --
> 2.27.0
>
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2 7/7] arm64: dts: mt8183: Add krane-sku176 board
2020-06-25 10:17 ` [PATCH v2 7/7] arm64: dts: mt8183: Add krane-sku176 board Enric Balletbo i Serra
@ 2020-07-02 5:07 ` Hsin-Yi Wang
0 siblings, 0 replies; 15+ messages in thread
From: Hsin-Yi Wang @ 2020-07-02 5:07 UTC (permalink / raw)
To: Enric Balletbo i Serra
Cc: erwanaliasr1, Nicolas Boichat, Devicetree List, Ben Ho, lkml,
Rob Herring, moderated list:ARM/Mediatek SoC support,
Matthias Brugger, Collabora Kernel ML,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
On Thu, Jun 25, 2020 at 6:18 PM Enric Balletbo i Serra
<enric.balletbo@collabora.com> wrote:
>
> Also known as the Lenovo IdeaPad Duet Chromebook.
>
> There are different krane boards with shared resources, hence a
> mt8183-kukui-krane.dtsi was created for easily introduce future new
> boards. The same happens with the baseboard codenamed kukui where
> different variants, apart from kukui variant can take advantage of the
> shared resources.
>
> Signed-off-by: Ben Ho <Ben.Ho@mediatek.com>
> [originally created by Ben Ho but adapted and ported to mainline]
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
> ---
>
> Changes in v2:
> - Move adding #phy-cells out of this patch. (Matthias Brugger)
>
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> .../mediatek/mt8183-kukui-krane-sku176.dts | 18 +
> .../boot/dts/mediatek/mt8183-kukui-krane.dtsi | 343 ++++++++
> .../arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 788 ++++++++++++++++++
> 4 files changed, 1150 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 848218f55bc1d..708fc60fa589a 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -12,4 +12,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
> new file mode 100644
> index 0000000000000..47113e275cb52
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
> @@ -0,0 +1,18 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2019 Google LLC
> + *
> + * Device-tree for Krane sku176.
> + *
> + * SKU is a 8-bit value (0xb0 == 176):
> + * - Bits 7..4: Panel ID: 0xb (BOE)
> + * - Bits 3..0: SKU ID: 0x0 (default)
> + */
> +
> +/dts-v1/;
> +#include "mt8183-kukui-krane.dtsi"
> +
> +/ {
> + model = "MediaTek krane sku176 board";
> + compatible = "google,krane-sku176", "google,krane", "mediatek,mt8183";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
> new file mode 100644
> index 0000000000000..fbc471ccf805f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
> @@ -0,0 +1,343 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2019 Google LLC
> + */
> +
> +#include "mt8183-kukui.dtsi"
> +
> +/ {
> + ppvarn_lcd: ppvarn-lcd {
> + compatible = "regulator-fixed";
> + regulator-name = "ppvarn_lcd";
> + pinctrl-names = "default";
> + pinctrl-0 = <&ppvarn_lcd_en>;
> +
> + enable-active-high;
> +
> + gpio = <&pio 66 GPIO_ACTIVE_HIGH>;
> + };
> +
> + ppvarp_lcd: ppvarp-lcd {
> + compatible = "regulator-fixed";
> + regulator-name = "ppvarp_lcd";
> + pinctrl-names = "default";
> + pinctrl-0 = <&ppvarp_lcd_en>;
> +
> + enable-active-high;
> +
> + gpio = <&pio 166 GPIO_ACTIVE_HIGH>;
> + };
> +
> + pp1800_lcd: pp1800-lcd {
> + compatible = "regulator-fixed";
> + regulator-name = "pp1800_lcd";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pp1800_lcd_en>;
> +
> + enable-active-high;
> +
> + gpio = <&pio 36 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&bluetooth {
> + firmware-name = "nvm_00440302_i2s_eu.bin";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + touchscreen4: touchscreen@5d {
> + compatible = "hid-over-i2c";
> + reg = <0x5d>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&open_touch>;
> +
> + interrupt-parent = <&pio>;
> + interrupts = <155 IRQ_TYPE_EDGE_FALLING>;
> +
> + post-power-on-delay-ms = <10>;
> + hid-descr-addr = <0x0001>;
> + };
> +};
> +
> +&mt6358_vcama2_reg {
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + eeprom@58 {
> + compatible = "atmel,24c32";
> + reg = <0x58>;
> + pagesize = <32>;
> + };
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4_pins>;
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + eeprom@54 {
> + compatible = "atmel,24c32";
> + reg = <0x54>;
> + pagesize = <32>;
> + };
> +};
> +
> +&pio {
> + /* 192 lines */
> + gpio-line-names =
> + "SPI_AP_EC_CS_L",
> + "SPI_AP_EC_MOSI",
> + "SPI_AP_EC_CLK",
> + "I2S3_DO",
> + "USB_PD_INT_ODL",
> + "",
> + "",
> + "",
> + "",
> + "IT6505_HPD_L",
> + "I2S3_TDM_D3",
> + "SOC_I2C6_1V8_SCL",
> + "SOC_I2C6_1V8_SDA",
> + "DPI_D0",
> + "DPI_D1",
> + "DPI_D2",
> + "DPI_D3",
> + "DPI_D4",
> + "DPI_D5",
> + "DPI_D6",
> + "DPI_D7",
> + "DPI_D8",
> + "DPI_D9",
> + "DPI_D10",
> + "DPI_D11",
> + "DPI_HSYNC",
> + "DPI_VSYNC",
> + "DPI_DE",
> + "DPI_CK",
> + "AP_MSDC1_CLK",
> + "AP_MSDC1_DAT3",
> + "AP_MSDC1_CMD",
> + "AP_MSDC1_DAT0",
> + "AP_MSDC1_DAT2",
> + "AP_MSDC1_DAT1",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "OTG_EN",
> + "DRVBUS",
> + "DISP_PWM",
> + "DSI_TE",
> + "LCM_RST_1V8",
> + "AP_CTS_WIFI_RTS",
> + "AP_RTS_WIFI_CTS",
> + "SOC_I2C5_1V8_SCL",
> + "SOC_I2C5_1V8_SDA",
> + "SOC_I2C3_1V8_SCL",
> + "SOC_I2C3_1V8_SDA",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "SOC_I2C1_1V8_SDA",
> + "SOC_I2C0_1V8_SDA",
> + "SOC_I2C0_1V8_SCL",
> + "SOC_I2C1_1V8_SCL",
> + "AP_SPI_H1_MISO",
> + "AP_SPI_H1_CS_L",
> + "AP_SPI_H1_MOSI",
> + "AP_SPI_H1_CLK",
> + "I2S5_BCK",
> + "I2S5_LRCK",
> + "I2S5_DO",
> + "BOOTBLOCK_EN_L",
> + "MT8183_KPCOL0",
> + "SPI_AP_EC_MISO",
> + "UART_DBG_TX_AP_RX",
> + "UART_AP_TX_DBG_RX",
> + "I2S2_MCK",
> + "I2S2_BCK",
> + "CLK_5M_WCAM",
> + "CLK_2M_UCAM",
> + "I2S2_LRCK",
> + "I2S2_DI",
> + "SOC_I2C2_1V8_SCL",
> + "SOC_I2C2_1V8_SDA",
> + "SOC_I2C4_1V8_SCL",
> + "SOC_I2C4_1V8_SDA",
> + "",
> + "SCL8",
> + "SDA8",
> + "FCAM_PWDN_L",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "I2S_PMIC",
> + "I2S_PMIC",
> + "I2S_PMIC",
> + "I2S_PMIC",
> + "I2S_PMIC",
> + "I2S_PMIC",
> + "I2S_PMIC",
> + "I2S_PMIC",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + /*
> + * AP_FLASH_WP_L is crossystem ABI. Rev1 schematics
> + * call it BIOS_FLASH_WP_R_L.
> + */
> + "AP_FLASH_WP_L",
> + "EC_AP_INT_ODL",
> + "IT6505_INT_ODL",
> + "H1_INT_OD_L",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "AP_SPI_FLASH_MISO",
> + "AP_SPI_FLASH_CS_L",
> + "AP_SPI_FLASH_MOSI",
> + "AP_SPI_FLASH_CLK",
> + "DA7219_IRQ",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "",
> + "";
> +
> + ppvarp_lcd_en: ppvarp-lcd-en {
> + pins1 {
> + pinmux = <PINMUX_GPIO66__FUNC_GPIO66>;
> + output-low;
> + };
> + };
> +
> + ppvarn_lcd_en: ppvarn-lcd-en {
> + pins1 {
> + pinmux = <PINMUX_GPIO166__FUNC_GPIO166>;
> + output-low;
> + };
> + };
> +
> + pp1800_lcd_en: pp1800-lcd-en {
> + pins1 {
> + pinmux = <PINMUX_GPIO36__FUNC_GPIO36>;
> + output-low;
> + };
> + };
> +
> + open_touch: open_touch {
> + irq_pin {
> + pinmux = <PINMUX_GPIO155__FUNC_GPIO155>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + rst_pin {
> + pinmux = <PINMUX_GPIO156__FUNC_GPIO156>;
> +
> + /*
> + * The pen driver doesn't currently support driving
> + * this reset line. By specifying output-high here
> + * we're relying on the fact that this pin has a default
> + * pulldown at boot (which makes sure the pen was in
> + * reset if it was powered) and then we set it high here
> + * to take it out of reset. Better would be if the pen
> + * driver could control this and we could remove
> + * "output-high" here.
> + */
> + output-high;
> + };
> + };
> +};
> +
> +&qca_wifi {
> + qcom,ath10k-calibration-variant = "LE_Krane";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
> new file mode 100644
> index 0000000000000..f0a070535b340
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
> @@ -0,0 +1,788 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (c) 2018 MediaTek Inc.
> + * Author: Ben Ho <ben.ho@mediatek.com>
> + * Erin Lo <erin.lo@mediatek.com>
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "mt8183.dtsi"
> +#include "mt6358.dtsi"
> +
> +/ {
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +
> + clk32k: oscillator1 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "clk32k";
> + };
> +
> + it6505_pp18_reg: regulator0 {
> + compatible = "regulator-fixed";
> + regulator-name = "it6505_pp18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&pio 178 0>;
> + enable-active-high;
> + };
> +
> + lcd_pp3300: regulator1 {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd_pp3300";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + bl_pp5000: regulator2 {
> + compatible = "regulator-fixed";
> + regulator-name = "bl_pp5000";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + mmc1_fixed_power: regulator3 {
> + compatible = "regulator-fixed";
> + regulator-name = "mmc1_power";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + mmc1_fixed_io: regulator4 {
> + compatible = "regulator-fixed";
> + regulator-name = "mmc1_io";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + pp1800_alw: regulator5 {
> + compatible = "regulator-fixed";
> + regulator-name = "pp1800_alw";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + pp3300_alw: regulator6 {
> + compatible = "regulator-fixed";
> + regulator-name = "pp3300_alw";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + max98357a: codec0 {
> + compatible = "maxim,max98357a";
> + sdmode-gpios = <&pio 175 0>;
> + };
> +
> + btsco: codec1 {
> + compatible = "linux,bt-sco";
> + };
> +
> + wifi_pwrseq: wifi-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_pins_pwrseq>;
> +
> + /* Toggle WIFI_ENABLE to reset the chip. */
> + reset-gpios = <&pio 119 1>;
> + };
> +
> + wifi_wakeup: wifi-wakeup {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_pins_wakeup>;
> +
> + wowlan {
> + label = "Wake on WiFi";
> + gpios = <&pio 113 GPIO_ACTIVE_HIGH>;
> + linux,code = <KEY_WAKEUP>;
> + wakeup-source;
> + };
> + };
> +
> + tboard_thermistor1: thermal-sensor1 {
> + compatible = "generic-adc-thermal";
> + #thermal-sensor-cells = <0>;
> + io-channels = <&auxadc 0>;
> + io-channel-names = "sensor-channel";
> + temperature-lookup-table = < (-5000) 4241
> + 0 4063
> + 5000 3856
> + 10000 3621
> + 15000 3364
> + 20000 3091
> + 25000 2810
> + 30000 2526
> + 35000 2247
> + 40000 1982
> + 45000 1734
> + 50000 1507
> + 55000 1305
> + 60000 1122
> + 65000 964
> + 70000 827
> + 75000 710
> + 80000 606
> + 85000 519
> + 90000 445
> + 95000 382
> + 100000 330
> + 105000 284
> + 110000 245
> + 115000 213
> + 120000 183
> + 125000 161>;
> + };
> +
> + tboard_thermistor2: thermal-sensor2 {
> + compatible = "generic-adc-thermal";
> + #thermal-sensor-cells = <0>;
> + io-channels = <&auxadc 1>;
> + io-channel-names = "sensor-channel";
> + temperature-lookup-table = < (-5000) 4241
> + 0 4063
> + 5000 3856
> + 10000 3621
> + 15000 3364
> + 20000 3091
> + 25000 2810
> + 30000 2526
> + 35000 2247
> + 40000 1982
> + 45000 1734
> + 50000 1507
> + 55000 1305
> + 60000 1122
> + 65000 964
> + 70000 827
> + 75000 710
> + 80000 606
> + 85000 519
> + 90000 445
> + 95000 382
> + 100000 330
> + 105000 284
> + 110000 245
> + 115000 213
> + 120000 183
> + 125000 161>;
> + };
> +};
> +
> +&auxadc {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + proc-supply = <&mt6358_vproc12_reg>;
> +};
> +
> +&cpu1 {
> + proc-supply = <&mt6358_vproc12_reg>;
> +};
> +
> +&cpu2 {
> + proc-supply = <&mt6358_vproc12_reg>;
> +};
> +
> +&cpu3 {
> + proc-supply = <&mt6358_vproc12_reg>;
> +};
> +
> +&cpu4 {
> + proc-supply = <&mt6358_vproc11_reg>;
> +};
> +
> +&cpu5 {
> + proc-supply = <&mt6358_vproc11_reg>;
> +};
> +
> +&cpu6 {
> + proc-supply = <&mt6358_vproc11_reg>;
> +};
> +
> +&cpu7 {
> + proc-supply = <&mt6358_vproc11_reg>;
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + status = "okay";
> + clock-frequency = <400000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + status = "okay";
> + clock-frequency = <100000>;
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> + status = "okay";
> + clock-frequency = <100000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +};
> +
> +&i2c5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c5_pins>;
> + status = "okay";
> + clock-frequency = <100000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +};
> +
> +&i2c6 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c6_pins>;
> + status = "okay";
> + clock-frequency = <100000>;
> +};
> +
> +&mmc0 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc0_pins_default>;
> + pinctrl-1 = <&mmc0_pins_uhs>;
> + bus-width = <8>;
> + max-frequency = <200000000>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + cap-mmc-hw-reset;
> + no-sdio;
> + no-sd;
> + hs400-ds-delay = <0x12814>;
> + vmmc-supply = <&mt6358_vemc_reg>;
> + vqmmc-supply = <&mt6358_vio18_reg>;
> + assigned-clocks = <&topckgen CLK_TOP_MUX_MSDC50_0>;
> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_CK>;
> + non-removable;
> +};
> +
> +&mmc1 {
> + status = "okay";
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc1_pins_default>;
> + pinctrl-1 = <&mmc1_pins_uhs>;
> + vmmc-supply = <&mmc1_fixed_power>;
> + vqmmc-supply = <&mmc1_fixed_io>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + drv-type = <2>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + keep-power-in-suspend;
> + enable-sdio-wakeup;
> + cap-sdio-irq;
> + non-removable;
> + no-mmc;
> + no-sd;
> + assigned-clocks = <&topckgen CLK_TOP_MUX_MSDC30_1>;
> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + qca_wifi: qca-wifi@1 {
> + compatible = "qcom,ath10k";
> + reg = <1>;
> + };
> +};
> +
> +&mt6358_vdram2_reg {
> + regulator-always-on;
> +};
> +
> +&mt6358codec {
> + Avdd-supply = <&mt6358_vaud28_reg>;
> +};
> +
> +&mt6358_vsim1_reg {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2700000>;
> +};
> +
> +&mt6358_vsim2_reg {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2700000>;
> +};
> +
> +&pio {
> + bt_pins: bt-pins {
> + pins_bt_en {
> + pinmux = <PINMUX_GPIO120__FUNC_GPIO120>;
> + output-low;
> + };
> + };
> +
> + ec_ap_int_odl: ec_ap_int_odl {
> + pins1 {
> + pinmux = <PINMUX_GPIO151__FUNC_GPIO151>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +
> + h1_int_od_l: h1_int_od_l {
> + pins1 {
> + pinmux = <PINMUX_GPIO153__FUNC_GPIO153>;
> + input-enable;
> + };
> + };
> +
> + i2c0_pins: i2c0 {
> + pins_bus {
> + pinmux = <PINMUX_GPIO82__FUNC_SDA0>,
> + <PINMUX_GPIO83__FUNC_SCL0>;
> + mediatek,pull-up-adv = <3>;
> + mediatek,drive-strength-adv = <00>;
> + };
> + };
> +
> + i2c1_pins: i2c1 {
> + pins_bus {
> + pinmux = <PINMUX_GPIO81__FUNC_SDA1>,
> + <PINMUX_GPIO84__FUNC_SCL1>;
> + mediatek,pull-up-adv = <3>;
> + mediatek,drive-strength-adv = <00>;
> + };
> + };
> +
> + i2c2_pins: i2c2 {
> + pins_bus {
> + pinmux = <PINMUX_GPIO103__FUNC_SCL2>,
> + <PINMUX_GPIO104__FUNC_SDA2>;
> + bias-disable;
> + mediatek,drive-strength-adv = <00>;
> + };
> + };
> +
> + i2c3_pins: i2c3 {
> + pins_bus {
> + pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
> + <PINMUX_GPIO51__FUNC_SDA3>;
> + mediatek,pull-up-adv = <3>;
> + mediatek,drive-strength-adv = <00>;
> + };
> + };
> +
> + i2c4_pins: i2c4 {
> + pins_bus {
> + pinmux = <PINMUX_GPIO105__FUNC_SCL4>,
> + <PINMUX_GPIO106__FUNC_SDA4>;
> + bias-disable;
> + mediatek,drive-strength-adv = <00>;
> + };
> + };
> +
> + i2c5_pins: i2c5 {
> + pins_bus {
> + pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
> + <PINMUX_GPIO49__FUNC_SDA5>;
> + mediatek,pull-up-adv = <3>;
> + mediatek,drive-strength-adv = <00>;
> + };
> + };
> +
> + i2c6_pins: i2c6 {
> + pins_bus {
> + pinmux = <PINMUX_GPIO11__FUNC_SCL6>,
> + <PINMUX_GPIO12__FUNC_SDA6>;
> + bias-disable;
> + };
> + };
> +
> + mmc0_pins_default: mmc0-pins-default {
> + pins_cmd_dat {
> + pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
> + <PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
> + <PINMUX_GPIO125__FUNC_MSDC0_DAT2>,
> + <PINMUX_GPIO132__FUNC_MSDC0_DAT3>,
> + <PINMUX_GPIO126__FUNC_MSDC0_DAT4>,
> + <PINMUX_GPIO129__FUNC_MSDC0_DAT5>,
> + <PINMUX_GPIO127__FUNC_MSDC0_DAT6>,
> + <PINMUX_GPIO130__FUNC_MSDC0_DAT7>,
> + <PINMUX_GPIO122__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_14mA>;
> + mediatek,pull-up-adv = <01>;
> + };
> +
> + pins_clk {
> + pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
> + drive-strength = <MTK_DRIVE_14mA>;
> + mediatek,pull-down-adv = <10>;
> + };
> +
> + pins_rst {
> + pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
> + drive-strength = <MTK_DRIVE_14mA>;
> + mediatek,pull-down-adv = <01>;
> + };
> + };
> +
> + mmc0_pins_uhs: mmc0-pins-uhs {
> + pins_cmd_dat {
> + pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
> + <PINMUX_GPIO128__FUNC_MSDC0_DAT1>,
> + <PINMUX_GPIO125__FUNC_MSDC0_DAT2>,
> + <PINMUX_GPIO132__FUNC_MSDC0_DAT3>,
> + <PINMUX_GPIO126__FUNC_MSDC0_DAT4>,
> + <PINMUX_GPIO129__FUNC_MSDC0_DAT5>,
> + <PINMUX_GPIO127__FUNC_MSDC0_DAT6>,
> + <PINMUX_GPIO130__FUNC_MSDC0_DAT7>,
> + <PINMUX_GPIO122__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_14mA>;
> + mediatek,pull-up-adv = <01>;
> + };
> +
> + pins_clk {
> + pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>;
> + drive-strength = <MTK_DRIVE_14mA>;
> + mediatek,pull-down-adv = <10>;
> + };
> +
> + pins_ds {
> + pinmux = <PINMUX_GPIO131__FUNC_MSDC0_DSL>;
> + drive-strength = <MTK_DRIVE_14mA>;
> + mediatek,pull-down-adv = <10>;
> + };
> +
> + pins_rst {
> + pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>;
> + drive-strength = <MTK_DRIVE_14mA>;
> + mediatek,pull-up-adv = <01>;
> + };
> + };
> +
> + mmc1_pins_default: mmc1-pins-default {
> + pins_cmd_dat {
> + pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
> + <PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO34__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO33__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO30__FUNC_MSDC1_DAT3>;
> + input-enable;
> + mediatek,pull-up-adv = <10>;
> + };
> +
> + pins_clk {
> + pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
> + input-enable;
> + mediatek,pull-down-adv = <10>;
> + };
> + };
> +
> + mmc1_pins_uhs: mmc1-pins-uhs {
> + pins_cmd_dat {
> + pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>,
> + <PINMUX_GPIO32__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO34__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO33__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO30__FUNC_MSDC1_DAT3>;
> + drive-strength = <MTK_DRIVE_6mA>;
> + input-enable;
> + mediatek,pull-up-adv = <10>;
> + };
> +
> + pins_clk {
> + pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + mediatek,pull-down-adv = <10>;
> + input-enable;
> + };
> + };
> +
> + spi0_pins: spi0 {
> + pins_spi{
> + pinmux = <PINMUX_GPIO85__FUNC_SPI0_MI>,
> + <PINMUX_GPIO86__FUNC_GPIO86>,
> + <PINMUX_GPIO87__FUNC_SPI0_MO>,
> + <PINMUX_GPIO88__FUNC_SPI0_CLK>;
> + bias-disable;
> + };
> + };
> +
> + spi1_pins: spi1 {
> + pins_spi{
> + pinmux = <PINMUX_GPIO161__FUNC_SPI1_A_MI>,
> + <PINMUX_GPIO162__FUNC_SPI1_A_CSB>,
> + <PINMUX_GPIO163__FUNC_SPI1_A_MO>,
> + <PINMUX_GPIO164__FUNC_SPI1_A_CLK>;
> + bias-disable;
> + };
> + };
> +
> + spi2_pins: spi2 {
> + pins_spi{
> + pinmux = <PINMUX_GPIO0__FUNC_SPI2_CSB>,
> + <PINMUX_GPIO1__FUNC_SPI2_MO>,
> + <PINMUX_GPIO2__FUNC_SPI2_CLK>;
> + bias-disable;
> + };
> + pins_spi_mi {
> + pinmux = <PINMUX_GPIO94__FUNC_SPI2_MI>;
> + mediatek,pull-down-adv = <00>;
> + };
> + };
> +
> + spi3_pins: spi3 {
> + pins_spi{
> + pinmux = <PINMUX_GPIO21__FUNC_SPI3_MI>,
> + <PINMUX_GPIO22__FUNC_SPI3_CSB>,
> + <PINMUX_GPIO23__FUNC_SPI3_MO>,
> + <PINMUX_GPIO24__FUNC_SPI3_CLK>;
> + bias-disable;
> + };
> + };
> +
> + spi4_pins: spi4 {
> + pins_spi{
> + pinmux = <PINMUX_GPIO17__FUNC_SPI4_MI>,
> + <PINMUX_GPIO18__FUNC_SPI4_CSB>,
> + <PINMUX_GPIO19__FUNC_SPI4_MO>,
> + <PINMUX_GPIO20__FUNC_SPI4_CLK>;
> + bias-disable;
> + };
> + };
> +
> + spi5_pins: spi5 {
> + pins_spi{
> + pinmux = <PINMUX_GPIO13__FUNC_SPI5_MI>,
> + <PINMUX_GPIO14__FUNC_SPI5_CSB>,
> + <PINMUX_GPIO15__FUNC_SPI5_MO>,
> + <PINMUX_GPIO16__FUNC_SPI5_CLK>;
> + bias-disable;
> + };
> + };
> +
> + uart0_pins_default: uart0-pins-default {
> + pins_rx {
> + pinmux = <PINMUX_GPIO95__FUNC_URXD0>;
> + input-enable;
> + bias-pull-up;
> + };
> + pins_tx {
> + pinmux = <PINMUX_GPIO96__FUNC_UTXD0>;
> + };
> + };
> +
> + uart1_pins_default: uart1-pins-default {
> + pins_rx {
> + pinmux = <PINMUX_GPIO121__FUNC_URXD1>;
> + input-enable;
> + bias-pull-up;
> + };
> + pins_tx {
> + pinmux = <PINMUX_GPIO115__FUNC_UTXD1>;
> + };
> + pins_rts {
> + pinmux = <PINMUX_GPIO47__FUNC_URTS1>;
> + output-enable;
> + };
> + pins_cts {
> + pinmux = <PINMUX_GPIO46__FUNC_UCTS1>;
> + input-enable;
> + };
> + };
> +
> + uart1_pins_sleep: uart1-pins-sleep {
> + pins_rx {
> + pinmux = <PINMUX_GPIO121__FUNC_GPIO121>;
> + input-enable;
> + bias-pull-up;
> + };
> + pins_tx {
> + pinmux = <PINMUX_GPIO115__FUNC_UTXD1>;
> + };
> + pins_rts {
> + pinmux = <PINMUX_GPIO47__FUNC_URTS1>;
> + output-enable;
> + };
> + pins_cts {
> + pinmux = <PINMUX_GPIO46__FUNC_UCTS1>;
> + input-enable;
> + };
> + };
> +
> + wifi_pins_pwrseq: wifi-pins-pwrseq {
> + pins_wifi_enable {
> + pinmux = <PINMUX_GPIO119__FUNC_GPIO119>;
> + output-low;
> + };
> + };
> +
> + wifi_pins_wakeup: wifi-pins-wakeup {
> + pins_wifi_wakeup {
> + pinmux = <PINMUX_GPIO113__FUNC_GPIO113>;
> + input-enable;
> + };
> + };
> +};
> +
> +&soc_data {
> + status = "okay";
> +};
> +
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi0_pins>;
> + mediatek,pad-select = <0>;
> + status = "okay";
> + cs-gpios = <&pio 86 GPIO_ACTIVE_LOW>;
> +
> + cr50@0 {
> + compatible = "google,cr50";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&h1_int_od_l>;
> + interrupt-parent = <&pio>;
> + interrupts = <153 IRQ_TYPE_EDGE_RISING>;
> + };
> +};
> +
> +&spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_pins>;
> + mediatek,pad-select = <0>;
> + status = "okay";
> +
> + w25q64dw: spi-flash@0 {
> + compatible = "winbond,w25q64dw", "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> + };
> +};
> +
> +&spi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2_pins>;
> + mediatek,pad-select = <0>;
> + status = "okay";
> +
> + cros_ec: cros-ec@0 {
> + compatible = "google,cros-ec-spi";
> + reg = <0>;
> + spi-max-frequency = <3000000>;
> + interrupt-parent = <&pio>;
> + interrupts = <151 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ec_ap_int_odl>;
> +
> + i2c_tunnel: i2c-tunnel {
> + compatible = "google,cros-ec-i2c-tunnel";
> + google,remote-bus = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + usbc_extcon: extcon0 {
> + compatible = "google,extcon-usbc-cros-ec";
> + google,usb-port-id = <0>;
> + };
> + };
> +};
> +
> +&spi3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi3_pins>;
> + mediatek,pad-select = <0>;
> + status = "disabled";
> +};
> +
> +&spi4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi4_pins>;
> + mediatek,pad-select = <0>;
> + status = "disabled";
> +};
> +
> +&spi5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi5_pins>;
> + mediatek,pad-select = <0>;
> + status = "disabled";
> +};
> +
> +&ssusb {
> + dr_mode = "host";
> + wakeup-source;
> + vusb33-supply = <&mt6358_vusb_reg>;
> + status = "okay";
> +};
> +
> +&u3phy {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_default>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&uart1_pins_default>;
> + pinctrl-1 = <&uart1_pins_sleep>;
> + status = "okay";
> + interrupts-extended = <&sysirq GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>,
> + <&pio 121 IRQ_TYPE_EDGE_FALLING>;
> +
> + bluetooth: bluetooth {
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_pins>;
> + status = "okay";
> + compatible = "qcom,qca6174-bt";
> + enable-gpios = <&pio 120 0>;
> + clocks = <&clk32k>;
> + firmware-name = "nvm_00440302_i2s.bin";
> + };
> +};
> +
> +&usb_host {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + vusb33-supply = <&mt6358_vusb_reg>;
> + status = "okay";
> +
> + hub@1 {
> + compatible = "usb5e3,610";
> + reg = <1>;
> + };
> +};
> +
> +#include <arm/cros-ec-keyboard.dtsi>
> +#include <arm/cros-ec-sbs.dtsi>
> --
> 2.27.0
>
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
` (6 preceding siblings ...)
2020-06-25 10:17 ` [PATCH v2 7/7] arm64: dts: mt8183: Add krane-sku176 board Enric Balletbo i Serra
@ 2020-07-10 13:35 ` Matthias Brugger
7 siblings, 0 replies; 15+ messages in thread
From: Matthias Brugger @ 2020-07-10 13:35 UTC (permalink / raw)
To: Enric Balletbo i Serra, linux-kernel
Cc: erwanaliasr1, drinkcat, devicetree, Sean Wang, Rob Herring,
Mars Cheng, hsinyi, linux-mediatek, Collabora Kernel ML,
linux-arm-kernel
On 25/06/2020 12:17, Enric Balletbo i Serra wrote:
> These series adds basic support for the Lenovo IdeaPad Duet Chromebook, a
> 2-in-1 detachable devices using the MediaTek MT8183 SoC. The first patch
> only adds the new compatible names in the mediatek binding. The second
> patch, adds the missing compatible to instantiate the PMIC regulators.
> The next patch adds missing devices to support better the board and fixes
> some warnings found running dtbs_check. And finally, the latest
> introduces support for the board itself.
>
> All the patches has been tested on Lenovo IdeaPad Duet Chromebook with
> the patches applied on top of 5.8-rc1 and with serial console, booting
> without problems and being able to go to the login prompt.
>
> Best regards,
> Enric
>
> Changes in v2:
> - Replace cluster-sleepX for cluster-sleep-x (Matthias Brugger)
> - [6/7] Move adding #phy-cells to this patch. (Matthias Brugger)
> - [7/7] Move adding #phy-cells out of this patch. (Matthias Brugger)
>
> Enric Balletbo i Serra (7):
> dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-krane-sku176
> arm64: dts: mt6358: Add the compatible for the regulators
> arm64: dts: mt8183: Add MediaTek's peripheral configuration controller
> arm64: dts: mt8183: Fix unit name warnings
> arm64: dts: mt8183-evb: Fix unit name warnings
> arm64: dts: mt8183: Add USB3.0 support
> arm64: dts: mt8183: Add krane-sku176 board
>
Whole series applied to v5.8-next/dts64
Thanks!
> .../devicetree/bindings/arm/mediatek.yaml | 5 +
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt6358.dtsi | 2 +
> arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 4 +-
> .../mediatek/mt8183-kukui-krane-sku176.dts | 18 +
> .../boot/dts/mediatek/mt8183-kukui-krane.dtsi | 343 ++++++++
> .../arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 788 ++++++++++++++++++
> arch/arm64/boot/dts/mediatek/mt8183.dtsi | 68 +-
> 8 files changed, 1225 insertions(+), 4 deletions(-)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
>
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2020-07-10 13:35 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-25 10:17 [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Enric Balletbo i Serra
2020-06-25 10:17 ` [PATCH v2 1/7] dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-krane-sku176 Enric Balletbo i Serra
2020-06-25 10:17 ` [PATCH v2 2/7] arm64: dts: mt6358: Add the compatible for the regulators Enric Balletbo i Serra
2020-07-02 5:04 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 3/7] arm64: dts: mt8183: Add MediaTek's peripheral configuration controller Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 4/7] arm64: dts: mt8183: Fix unit name warnings Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 5/7] arm64: dts: mt8183-evb: " Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 6/7] arm64: dts: mt8183: Add USB3.0 support Enric Balletbo i Serra
2020-07-02 5:06 ` Hsin-Yi Wang
2020-06-25 10:17 ` [PATCH v2 7/7] arm64: dts: mt8183: Add krane-sku176 board Enric Balletbo i Serra
2020-07-02 5:07 ` Hsin-Yi Wang
2020-07-10 13:35 ` [PATCH v2 0/7] arm64: dts: mediatek: Add support for Lenovo IdeaPad Duet Chromebook Matthias Brugger
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).