Re: [PATCH] net: dsa: mt7530: fix null pointer dereferencing in port5 setup

From: Chuanhong Guo <gch981213@gmail.com>
To: "René van Dorst" <opensource@vdorst.com>
Cc: Andrew Lunn <andrew@lunn.ch>,
	Florian Fainelli <f.fainelli@gmail.com>,
	netdev@vger.kernel.org, Sean Wang <sean.wang@mediatek.com>,
	open list <linux-kernel@vger.kernel.org>,
	stable@vger.kernel.org, "David S. Miller" <davem@davemloft.net>,
	Russell King <rmk+kernel@armlinux.org.uk>,
	linux-mediatek@lists.infradead.org,
	Matthias Brugger <matthias.bgg@gmail.com>,
	Vivien Didelot <vivien.didelot@gmail.com>,
	"moderated list:ARM/Mediatek SoC support"
	<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH] net: dsa: mt7530: fix null pointer dereferencing in port5 setup
Date: Sat, 4 Apr 2020 11:19:10 +0800	[thread overview]
Message-ID: <CAJsYDVJj1JajVxeGifaOprXYstG-gC_OYwd5LrALUY_4BdtR3A@mail.gmail.com> (raw)
In-Reply-To: <20200403180911.Horde.9xqnJvjcRDe-ttshlJbG6WE@www.vdorst.com>

Hi!

On Sat, Apr 4, 2020 at 2:09 AM René van Dorst <opensource@vdorst.com> wrote:
>
> Quoting Chuanhong Guo <gch981213@gmail.com>:
>
> Hi Chuanhong,
>
> > The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
> > and a phy-handle isn't always available.
> > Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
> > connected to switch port 5 and setup mt7530 according to phy address
> > of 2nd gmac node, causing null pointer dereferencing when phy-handle
> > isn't defined in dts.
>
> MT7530 tries to detect if 2nd GMAC is using a phy with phy-address 0 or 4.

What if the 2nd GMAC connects to an external PHY on address 0 on a
different mdio-bus? This is already happening on mt7629 where the
integrated PHY connected to gmac2 is on address 0 and gmac1
connects to external mt753x switch.
On mt7621, the RGMII2 is always wired to switch mac5 as well as
external pins, and one should disable switch mac5 in this case or
there's pin conflict.

> If so, switch port 5 needs to be setup so that PHY 0 or 4 is available
> via port 5 of the switch. Any MAC can talk to PHY 0/4 directly via port 5.
> This is also explained in the kernel docs mt7530.txt.
>
> May be there are better way to detect that any node is using phy 0/4 of
> the switch.

It should never be detected. This piece of code is to configure how
RGMII2 on mt7530 is wired: PHY0/PHY4/switch MAC5/off. And it
should be implemented as a configurable dt property. We should
not make assumption that 2 RGMIIs always connected to the two
macs on mtk_eth_soc and we should never parse parent eth dts
in DSA driver.

-- 
Regards,
Chuanhong Guo

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek