linux-mips.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Oleksij Rempel <o.rempel@pengutronix.de>
To: Andrew Lunn <andrew@lunn.ch>, Chris Snook <chris.snook@gmail.com>,
	Florian Fainelli <f.fainelli@gmail.com>,
	James Hogan <jhogan@kernel.org>, Jay Cliburn <jcliburn@gmail.com>,
	Mark Rutland <mark.rutland@arm.com>,
	Paul Burton <paul.burton@mips.com>,
	Ralf Baechle <ralf@linux-mips.org>,
	Rob Herring <robh+dt@kernel.org>,
	Vivien Didelot <vivien.didelot@gmail.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	"David S. Miller" <davem@davemloft.net>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, linux-mips@vger.kernel.org,
	Russell King <linux@armlinux.org.uk>
Subject: [PATCH v4 1/5] net: ag71xx: port to phylink
Date: Tue, 22 Oct 2019 07:57:39 +0200	[thread overview]
Message-ID: <20191022055743.6832-2-o.rempel@pengutronix.de> (raw)
In-Reply-To: <20191022055743.6832-1-o.rempel@pengutronix.de>

The port to phylink was done as close as possible to initial
functionality.
Theoretically this HW can support flow control, practically seems to be not
enough to just enable it. So, more work should be done.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/ethernet/atheros/Kconfig  |   2 +-
 drivers/net/ethernet/atheros/ag71xx.c | 146 ++++++++++++++++----------
 2 files changed, 89 insertions(+), 59 deletions(-)

diff --git a/drivers/net/ethernet/atheros/Kconfig b/drivers/net/ethernet/atheros/Kconfig
index 0058051ba925..2720bde5034e 100644
--- a/drivers/net/ethernet/atheros/Kconfig
+++ b/drivers/net/ethernet/atheros/Kconfig
@@ -20,7 +20,7 @@ if NET_VENDOR_ATHEROS
 config AG71XX
 	tristate "Atheros AR7XXX/AR9XXX built-in ethernet mac support"
 	depends on ATH79
-	select PHYLIB
+	select PHYLINK
 	help
 	  If you wish to compile a kernel for AR7XXX/91XXX and enable
 	  ethernet support, then you should always answer Y to this.
diff --git a/drivers/net/ethernet/atheros/ag71xx.c b/drivers/net/ethernet/atheros/ag71xx.c
index 1b1a09095c0d..9d766d73a89b 100644
--- a/drivers/net/ethernet/atheros/ag71xx.c
+++ b/drivers/net/ethernet/atheros/ag71xx.c
@@ -32,6 +32,7 @@
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/of_platform.h>
+#include <linux/phylink.h>
 #include <linux/regmap.h>
 #include <linux/reset.h>
 #include <linux/clk.h>
@@ -314,6 +315,8 @@ struct ag71xx {
 	dma_addr_t stop_desc_dma;
 
 	int phy_if_mode;
+	struct phylink *phylink;
+	struct phylink_config phylink_config;
 
 	struct delayed_work restart_work;
 	struct timer_list oom_timer;
@@ -845,24 +848,23 @@ static void ag71xx_hw_start(struct ag71xx *ag)
 	netif_wake_queue(ag->ndev);
 }
 
-static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
+static void ag71xx_mac_config(struct phylink_config *config, unsigned int mode,
+			      const struct phylink_link_state *state)
 {
-	struct phy_device *phydev = ag->ndev->phydev;
+	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
 	u32 cfg2;
 	u32 ifctl;
 	u32 fifo5;
 
-	if (!phydev->link && update) {
-		ag71xx_hw_stop(ag);
+	if (phylink_autoneg_inband(mode))
 		return;
-	}
 
 	if (!ag71xx_is(ag, AR7100) && !ag71xx_is(ag, AR9130))
 		ag71xx_fast_reset(ag);
 
 	cfg2 = ag71xx_rr(ag, AG71XX_REG_MAC_CFG2);
 	cfg2 &= ~(MAC_CFG2_IF_1000 | MAC_CFG2_IF_10_100 | MAC_CFG2_FDX);
-	cfg2 |= (phydev->duplex) ? MAC_CFG2_FDX : 0;
+	cfg2 |= (state->duplex) ? MAC_CFG2_FDX : 0;
 
 	ifctl = ag71xx_rr(ag, AG71XX_REG_MAC_IFCTL);
 	ifctl &= ~(MAC_IFCTL_SPEED);
@@ -870,7 +872,7 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
 	fifo5 = ag71xx_rr(ag, AG71XX_REG_FIFO_CFG5);
 	fifo5 &= ~FIFO_CFG5_BM;
 
-	switch (phydev->speed) {
+	switch (state->speed) {
 	case SPEED_1000:
 		cfg2 |= MAC_CFG2_IF_1000;
 		fifo5 |= FIFO_CFG5_BM;
@@ -883,7 +885,6 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
 		cfg2 |= MAC_CFG2_IF_10_100;
 		break;
 	default:
-		WARN(1, "not supported speed %i\n", phydev->speed);
 		return;
 	}
 
@@ -897,58 +898,79 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
 	ag71xx_wr(ag, AG71XX_REG_MAC_CFG2, cfg2);
 	ag71xx_wr(ag, AG71XX_REG_FIFO_CFG5, fifo5);
 	ag71xx_wr(ag, AG71XX_REG_MAC_IFCTL, ifctl);
-
-	ag71xx_hw_start(ag);
-
-	if (update)
-		phy_print_status(phydev);
 }
 
-static void ag71xx_phy_link_adjust(struct net_device *ndev)
+static void ag71xx_mac_validate(struct phylink_config *config,
+			    unsigned long *supported,
+			    struct phylink_link_state *state)
 {
-	struct ag71xx *ag = netdev_priv(ndev);
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+	if (state->interface != PHY_INTERFACE_MODE_NA &&
+	    state->interface != PHY_INTERFACE_MODE_GMII &&
+	    state->interface != PHY_INTERFACE_MODE_MII) {
+		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+		return;
+	}
+
+	phylink_set(mask, MII);
+
+	/* flow control is not supported */
+
+	phylink_set(mask, 10baseT_Half);
+	phylink_set(mask, 10baseT_Full);
+	phylink_set(mask, 100baseT_Half);
+	phylink_set(mask, 100baseT_Full);
 
-	ag71xx_link_adjust(ag, true);
+	if (state->interface == PHY_INTERFACE_MODE_NA ||
+	    state->interface == PHY_INTERFACE_MODE_GMII) {
+		phylink_set(mask, 1000baseT_Full);
+		phylink_set(mask, 1000baseX_Full);
+	}
+
+	bitmap_and(supported, supported, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+	bitmap_and(state->advertising, state->advertising, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
 }
 
-static int ag71xx_phy_connect(struct ag71xx *ag)
+static void ag71xx_mac_link_down(struct phylink_config *config,
+				 unsigned int mode, phy_interface_t interface)
 {
-	struct device_node *np = ag->pdev->dev.of_node;
-	struct net_device *ndev = ag->ndev;
-	struct device_node *phy_node;
-	struct phy_device *phydev;
-	int ret;
+	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
 
-	if (of_phy_is_fixed_link(np)) {
-		ret = of_phy_register_fixed_link(np);
-		if (ret < 0) {
-			netif_err(ag, probe, ndev, "Failed to register fixed PHY link: %d\n",
-				  ret);
-			return ret;
-		}
+	ag71xx_hw_stop(ag);
+}
 
-		phy_node = of_node_get(np);
-	} else {
-		phy_node = of_parse_phandle(np, "phy-handle", 0);
-	}
+static void ag71xx_mac_link_up(struct phylink_config *config, unsigned int mode,
+			       phy_interface_t interface,
+			       struct phy_device *phy)
+{
+	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
 
-	if (!phy_node) {
-		netif_err(ag, probe, ndev, "Could not find valid phy node\n");
-		return -ENODEV;
-	}
+	ag71xx_hw_start(ag);
+}
 
-	phydev = of_phy_connect(ag->ndev, phy_node, ag71xx_phy_link_adjust,
-				0, ag->phy_if_mode);
+static const struct phylink_mac_ops ag71xx_phylink_mac_ops = {
+	.validate = ag71xx_mac_validate,
+	.mac_config = ag71xx_mac_config,
+	.mac_link_down = ag71xx_mac_link_down,
+	.mac_link_up = ag71xx_mac_link_up,
+};
 
-	of_node_put(phy_node);
+static int ag71xx_phy_setup(struct ag71xx *ag)
+{
+	struct phylink *phylink;
 
-	if (!phydev) {
-		netif_err(ag, probe, ndev, "Could not connect to PHY device\n");
-		return -ENODEV;
-	}
+	ag->phylink_config.dev = &ag->ndev->dev;
+	ag->phylink_config.type = PHYLINK_NETDEV;
 
-	phy_attached_info(phydev);
+	phylink = phylink_create(&ag->phylink_config, ag->pdev->dev.fwnode,
+				 ag->phy_if_mode, &ag71xx_phylink_mac_ops);
+	if (IS_ERR(phylink))
+		return PTR_ERR(phylink);
 
+	ag->phylink = phylink;
 	return 0;
 }
 
@@ -1239,6 +1261,13 @@ static int ag71xx_open(struct net_device *ndev)
 	unsigned int max_frame_len;
 	int ret;
 
+	ret = phylink_of_phy_connect(ag->phylink, ag->pdev->dev.of_node, 0);
+	if (ret) {
+		netif_err(ag, link, ndev, "phylink_of_phy_connect filed with err: %i\n",
+			  ret);
+		goto err;
+	}
+
 	max_frame_len = ag71xx_max_frame_len(ndev->mtu);
 	ag->rx_buf_size =
 		SKB_DATA_ALIGN(max_frame_len + NET_SKB_PAD + NET_IP_ALIGN);
@@ -1251,11 +1280,7 @@ static int ag71xx_open(struct net_device *ndev)
 	if (ret)
 		goto err;
 
-	ret = ag71xx_phy_connect(ag);
-	if (ret)
-		goto err;
-
-	phy_start(ndev->phydev);
+	phylink_start(ag->phylink);
 
 	return 0;
 
@@ -1268,8 +1293,7 @@ static int ag71xx_stop(struct net_device *ndev)
 {
 	struct ag71xx *ag = netdev_priv(ndev);
 
-	phy_stop(ndev->phydev);
-	phy_disconnect(ndev->phydev);
+	phylink_stop(ag->phylink);
 	ag71xx_hw_disable(ag);
 
 	return 0;
@@ -1396,10 +1420,9 @@ static netdev_tx_t ag71xx_hard_start_xmit(struct sk_buff *skb,
 
 static int ag71xx_do_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
 {
-	if (!ndev->phydev)
-		return -EINVAL;
+	struct ag71xx *ag = netdev_priv(ndev);
 
-	return phy_mii_ioctl(ndev->phydev, ifr, cmd);
+	return phylink_mii_ioctl(ag->phylink, ifr, cmd);
 }
 
 static void ag71xx_oom_timer_handler(struct timer_list *t)
@@ -1422,13 +1445,14 @@ static void ag71xx_restart_work_func(struct work_struct *work)
 {
 	struct ag71xx *ag = container_of(work, struct ag71xx,
 					 restart_work.work);
-	struct net_device *ndev = ag->ndev;
 
 	rtnl_lock();
 	ag71xx_hw_disable(ag);
 	ag71xx_hw_enable(ag);
-	if (ndev->phydev->link)
-		ag71xx_link_adjust(ag, false);
+
+	phylink_stop(ag->phylink);
+	phylink_start(ag->phylink);
+
 	rtnl_unlock();
 }
 
@@ -1769,6 +1793,12 @@ static int ag71xx_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, ndev);
 
+	err = ag71xx_phy_setup(ag);
+	if (err) {
+		netif_err(ag, probe, ndev, "failed to setup phy (%d)\n", err);
+		goto err_mdio_remove;
+	}
+
 	err = register_netdev(ndev);
 	if (err) {
 		netif_err(ag, probe, ndev, "unable to register net device\n");
-- 
2.23.0


  reply	other threads:[~2019-10-22  5:58 UTC|newest]

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-22  5:57 [PATCH v4 0/5] add dsa switch support for ar9331 Oleksij Rempel
2019-10-22  5:57 ` Oleksij Rempel [this message]
2019-10-22  5:57 ` [PATCH v4 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation Oleksij Rempel
2019-10-23  0:35   ` Andrew Lunn
2019-10-29  7:34     ` Oleksij Rempel
2019-12-15 14:57       ` Oleksij Rempel
2019-12-17  8:44         ` Andrew Lunn
2019-10-22  5:57 ` [PATCH v4 3/5] MIPS: ath79: ar9331: add ar9331-switch node Oleksij Rempel
2019-10-22  5:57 ` [PATCH v4 4/5] net: dsa: add support for Atheros AR9331 TAG format Oleksij Rempel
2019-10-22  6:10   ` Randy Dunlap
2019-10-23  0:37   ` Andrew Lunn
2019-10-22  5:57 ` [PATCH v4 5/5] net: dsa: add support for Atheros AR9331 build-in switch Oleksij Rempel
2019-10-22  6:10   ` Randy Dunlap
2019-10-23  0:58   ` Andrew Lunn
2019-10-29  7:14     ` Oleksij Rempel
2019-10-29 12:38       ` Andrew Lunn

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191022055743.6832-2-o.rempel@pengutronix.de \
    --to=o.rempel@pengutronix.de \
    --cc=andrew@lunn.ch \
    --cc=chris.snook@gmail.com \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=f.fainelli@gmail.com \
    --cc=jcliburn@gmail.com \
    --cc=jhogan@kernel.org \
    --cc=kernel@pengutronix.de \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mips@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=mark.rutland@arm.com \
    --cc=netdev@vger.kernel.org \
    --cc=paul.burton@mips.com \
    --cc=ralf@linux-mips.org \
    --cc=robh+dt@kernel.org \
    --cc=vivien.didelot@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).