linux-mips.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v6 0/5] add dsa switch support for ar9331
@ 2019-12-17  7:23 Oleksij Rempel
  2019-12-17  7:23 ` [PATCH v6 1/5] net: ag71xx: port to phylink Oleksij Rempel
                   ` (4 more replies)
  0 siblings, 5 replies; 8+ messages in thread
From: Oleksij Rempel @ 2019-12-17  7:23 UTC (permalink / raw)
  To: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Rob Herring, Vivien Didelot
  Cc: Oleksij Rempel, Pengutronix Kernel Team, David S. Miller, netdev,
	linux-kernel, devicetree, linux-mips, Russell King

changes v6:
- rebase against net-next

changes v5:
- remote support for port5. The effort of using this port is
  questionable. Currently, it is better to not use it at all, then
  adding buggy support.
- remove port enable call back. There is nothing what we actually need
  to enable.
- rebase it against v5.5-rc1 

changes v4:
- ag71xx: ag71xx_mac_validate fix always false comparison (&& -> ||)
- tag_ar9331: use skb_pull_rcsum() instead of skb_pull().
- tag_ar9331: drop skb_set_mac_header()

changes v3:
- ag71xx: ag71xx_mac_config: ignore MLO_AN_INBAND mode. It is not
  supported by HW and SW.
- ag71xx: ag71xx_mac_validate: return all supported bits on
  PHY_INTERFACE_MODE_NA

changes v2:
- move Atheros AR9331 TAG format to separate patch
- use netdev_warn_once in the tag driver to reduce potential message spam
- typo fixes
- reorder tag driver alphabetically 
- configure switch to maximal frame size
- use mdiobus_read/write
- fail if mdio sub node is not found
- add comment for post reset state
- remove deprecated comment about device id
- remove phy-handle option for node with fixed-link
- ag71xx: set 1G support only for GMII mode

This patch series provides dsa switch support for Atheros ar9331 WiSoC.
As side effect ag71xx needed to be ported to phylink to make the switch
driver (as well phylink based) work properly.

Oleksij Rempel (5):
  net: ag71xx: port to phylink
  dt-bindings: net: dsa: qca,ar9331 switch documentation
  MIPS: ath79: ar9331: add ar9331-switch node
  net: dsa: add support for Atheros AR9331 TAG format
  net: dsa: add support for Atheros AR9331 built-in switch

 .../devicetree/bindings/net/dsa/ar9331.txt    | 148 ++++
 arch/mips/boot/dts/qca/ar9331.dtsi            | 119 ++-
 arch/mips/boot/dts/qca/ar9331_dpt_module.dts  |  13 +
 drivers/net/dsa/Kconfig                       |   2 +
 drivers/net/dsa/Makefile                      |   1 +
 drivers/net/dsa/qca/Kconfig                   |  11 +
 drivers/net/dsa/qca/Makefile                  |   2 +
 drivers/net/dsa/qca/ar9331.c                  | 817 ++++++++++++++++++
 drivers/net/ethernet/atheros/Kconfig          |   2 +-
 drivers/net/ethernet/atheros/ag71xx.c         | 147 ++--
 include/net/dsa.h                             |   2 +
 net/dsa/Kconfig                               |   6 +
 net/dsa/Makefile                              |   1 +
 net/dsa/tag_ar9331.c                          |  96 ++
 14 files changed, 1307 insertions(+), 60 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/ar9331.txt
 create mode 100644 drivers/net/dsa/qca/Kconfig
 create mode 100644 drivers/net/dsa/qca/Makefile
 create mode 100644 drivers/net/dsa/qca/ar9331.c
 create mode 100644 net/dsa/tag_ar9331.c

-- 
2.24.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v6 1/5] net: ag71xx: port to phylink
  2019-12-17  7:23 [PATCH v6 0/5] add dsa switch support for ar9331 Oleksij Rempel
@ 2019-12-17  7:23 ` Oleksij Rempel
  2019-12-17 10:00   ` Russell King - ARM Linux admin
  2019-12-17  7:23 ` [PATCH v6 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation Oleksij Rempel
                   ` (3 subsequent siblings)
  4 siblings, 1 reply; 8+ messages in thread
From: Oleksij Rempel @ 2019-12-17  7:23 UTC (permalink / raw)
  To: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Rob Herring, Vivien Didelot
  Cc: Oleksij Rempel, Pengutronix Kernel Team, David S. Miller, netdev,
	linux-kernel, devicetree, linux-mips, Russell King

The port to phylink was done as close as possible to initial
functionality.
Theoretically this HW can support flow control, practically seems to be not
enough to just enable it. So, more work should be done.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/ethernet/atheros/Kconfig  |   2 +-
 drivers/net/ethernet/atheros/ag71xx.c | 147 ++++++++++++++++----------
 2 files changed, 90 insertions(+), 59 deletions(-)

diff --git a/drivers/net/ethernet/atheros/Kconfig b/drivers/net/ethernet/atheros/Kconfig
index 0058051ba925..2720bde5034e 100644
--- a/drivers/net/ethernet/atheros/Kconfig
+++ b/drivers/net/ethernet/atheros/Kconfig
@@ -20,7 +20,7 @@ if NET_VENDOR_ATHEROS
 config AG71XX
 	tristate "Atheros AR7XXX/AR9XXX built-in ethernet mac support"
 	depends on ATH79
-	select PHYLIB
+	select PHYLINK
 	help
 	  If you wish to compile a kernel for AR7XXX/91XXX and enable
 	  ethernet support, then you should always answer Y to this.
diff --git a/drivers/net/ethernet/atheros/ag71xx.c b/drivers/net/ethernet/atheros/ag71xx.c
index ad8b0e3fcd2c..37a62283719e 100644
--- a/drivers/net/ethernet/atheros/ag71xx.c
+++ b/drivers/net/ethernet/atheros/ag71xx.c
@@ -32,6 +32,7 @@
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/of_platform.h>
+#include <linux/phylink.h>
 #include <linux/regmap.h>
 #include <linux/reset.h>
 #include <linux/clk.h>
@@ -315,6 +316,9 @@ struct ag71xx {
 
 	int phy_if_mode;
 
+	struct phylink *phylink;
+	struct phylink_config phylink_config;
+
 	struct delayed_work restart_work;
 	struct timer_list oom_timer;
 
@@ -845,24 +849,23 @@ static void ag71xx_hw_start(struct ag71xx *ag)
 	netif_wake_queue(ag->ndev);
 }
 
-static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
+static void ag71xx_mac_config(struct phylink_config *config, unsigned int mode,
+			      const struct phylink_link_state *state)
 {
-	struct phy_device *phydev = ag->ndev->phydev;
+	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
 	u32 cfg2;
 	u32 ifctl;
 	u32 fifo5;
 
-	if (!phydev->link && update) {
-		ag71xx_hw_stop(ag);
+	if (phylink_autoneg_inband(mode))
 		return;
-	}
 
 	if (!ag71xx_is(ag, AR7100) && !ag71xx_is(ag, AR9130))
 		ag71xx_fast_reset(ag);
 
 	cfg2 = ag71xx_rr(ag, AG71XX_REG_MAC_CFG2);
 	cfg2 &= ~(MAC_CFG2_IF_1000 | MAC_CFG2_IF_10_100 | MAC_CFG2_FDX);
-	cfg2 |= (phydev->duplex) ? MAC_CFG2_FDX : 0;
+	cfg2 |= (state->duplex) ? MAC_CFG2_FDX : 0;
 
 	ifctl = ag71xx_rr(ag, AG71XX_REG_MAC_IFCTL);
 	ifctl &= ~(MAC_IFCTL_SPEED);
@@ -870,7 +873,7 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
 	fifo5 = ag71xx_rr(ag, AG71XX_REG_FIFO_CFG5);
 	fifo5 &= ~FIFO_CFG5_BM;
 
-	switch (phydev->speed) {
+	switch (state->speed) {
 	case SPEED_1000:
 		cfg2 |= MAC_CFG2_IF_1000;
 		fifo5 |= FIFO_CFG5_BM;
@@ -883,7 +886,6 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
 		cfg2 |= MAC_CFG2_IF_10_100;
 		break;
 	default:
-		WARN(1, "not supported speed %i\n", phydev->speed);
 		return;
 	}
 
@@ -897,58 +899,79 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
 	ag71xx_wr(ag, AG71XX_REG_MAC_CFG2, cfg2);
 	ag71xx_wr(ag, AG71XX_REG_FIFO_CFG5, fifo5);
 	ag71xx_wr(ag, AG71XX_REG_MAC_IFCTL, ifctl);
-
-	ag71xx_hw_start(ag);
-
-	if (update)
-		phy_print_status(phydev);
 }
 
-static void ag71xx_phy_link_adjust(struct net_device *ndev)
+static void ag71xx_mac_validate(struct phylink_config *config,
+			    unsigned long *supported,
+			    struct phylink_link_state *state)
 {
-	struct ag71xx *ag = netdev_priv(ndev);
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+	if (state->interface != PHY_INTERFACE_MODE_NA &&
+	    state->interface != PHY_INTERFACE_MODE_GMII &&
+	    state->interface != PHY_INTERFACE_MODE_MII) {
+		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+		return;
+	}
+
+	phylink_set(mask, MII);
+
+	/* flow control is not supported */
+
+	phylink_set(mask, 10baseT_Half);
+	phylink_set(mask, 10baseT_Full);
+	phylink_set(mask, 100baseT_Half);
+	phylink_set(mask, 100baseT_Full);
 
-	ag71xx_link_adjust(ag, true);
+	if (state->interface == PHY_INTERFACE_MODE_NA ||
+	    state->interface == PHY_INTERFACE_MODE_GMII) {
+		phylink_set(mask, 1000baseT_Full);
+		phylink_set(mask, 1000baseX_Full);
+	}
+
+	bitmap_and(supported, supported, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+	bitmap_and(state->advertising, state->advertising, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
 }
 
-static int ag71xx_phy_connect(struct ag71xx *ag)
+static void ag71xx_mac_link_down(struct phylink_config *config,
+				 unsigned int mode, phy_interface_t interface)
 {
-	struct device_node *np = ag->pdev->dev.of_node;
-	struct net_device *ndev = ag->ndev;
-	struct device_node *phy_node;
-	struct phy_device *phydev;
-	int ret;
+	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
 
-	if (of_phy_is_fixed_link(np)) {
-		ret = of_phy_register_fixed_link(np);
-		if (ret < 0) {
-			netif_err(ag, probe, ndev, "Failed to register fixed PHY link: %d\n",
-				  ret);
-			return ret;
-		}
+	ag71xx_hw_stop(ag);
+}
 
-		phy_node = of_node_get(np);
-	} else {
-		phy_node = of_parse_phandle(np, "phy-handle", 0);
-	}
+static void ag71xx_mac_link_up(struct phylink_config *config, unsigned int mode,
+			       phy_interface_t interface,
+			       struct phy_device *phy)
+{
+	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
 
-	if (!phy_node) {
-		netif_err(ag, probe, ndev, "Could not find valid phy node\n");
-		return -ENODEV;
-	}
+	ag71xx_hw_start(ag);
+}
 
-	phydev = of_phy_connect(ag->ndev, phy_node, ag71xx_phy_link_adjust,
-				0, ag->phy_if_mode);
+static const struct phylink_mac_ops ag71xx_phylink_mac_ops = {
+	.validate = ag71xx_mac_validate,
+	.mac_config = ag71xx_mac_config,
+	.mac_link_down = ag71xx_mac_link_down,
+	.mac_link_up = ag71xx_mac_link_up,
+};
 
-	of_node_put(phy_node);
+static int ag71xx_phy_setup(struct ag71xx *ag)
+{
+	struct phylink *phylink;
 
-	if (!phydev) {
-		netif_err(ag, probe, ndev, "Could not connect to PHY device\n");
-		return -ENODEV;
-	}
+	ag->phylink_config.dev = &ag->ndev->dev;
+	ag->phylink_config.type = PHYLINK_NETDEV;
 
-	phy_attached_info(phydev);
+	phylink = phylink_create(&ag->phylink_config, ag->pdev->dev.fwnode,
+				 ag->phy_if_mode, &ag71xx_phylink_mac_ops);
+	if (IS_ERR(phylink))
+		return PTR_ERR(phylink);
 
+	ag->phylink = phylink;
 	return 0;
 }
 
@@ -1239,6 +1262,13 @@ static int ag71xx_open(struct net_device *ndev)
 	unsigned int max_frame_len;
 	int ret;
 
+	ret = phylink_of_phy_connect(ag->phylink, ag->pdev->dev.of_node, 0);
+	if (ret) {
+		netif_err(ag, link, ndev, "phylink_of_phy_connect filed with err: %i\n",
+			  ret);
+		goto err;
+	}
+
 	max_frame_len = ag71xx_max_frame_len(ndev->mtu);
 	ag->rx_buf_size =
 		SKB_DATA_ALIGN(max_frame_len + NET_SKB_PAD + NET_IP_ALIGN);
@@ -1251,11 +1281,7 @@ static int ag71xx_open(struct net_device *ndev)
 	if (ret)
 		goto err;
 
-	ret = ag71xx_phy_connect(ag);
-	if (ret)
-		goto err;
-
-	phy_start(ndev->phydev);
+	phylink_start(ag->phylink);
 
 	return 0;
 
@@ -1268,8 +1294,7 @@ static int ag71xx_stop(struct net_device *ndev)
 {
 	struct ag71xx *ag = netdev_priv(ndev);
 
-	phy_stop(ndev->phydev);
-	phy_disconnect(ndev->phydev);
+	phylink_stop(ag->phylink);
 	ag71xx_hw_disable(ag);
 
 	return 0;
@@ -1396,10 +1421,9 @@ static netdev_tx_t ag71xx_hard_start_xmit(struct sk_buff *skb,
 
 static int ag71xx_do_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
 {
-	if (!ndev->phydev)
-		return -EINVAL;
+	struct ag71xx *ag = netdev_priv(ndev);
 
-	return phy_mii_ioctl(ndev->phydev, ifr, cmd);
+	return phylink_mii_ioctl(ag->phylink, ifr, cmd);
 }
 
 static void ag71xx_oom_timer_handler(struct timer_list *t)
@@ -1422,13 +1446,14 @@ static void ag71xx_restart_work_func(struct work_struct *work)
 {
 	struct ag71xx *ag = container_of(work, struct ag71xx,
 					 restart_work.work);
-	struct net_device *ndev = ag->ndev;
 
 	rtnl_lock();
 	ag71xx_hw_disable(ag);
 	ag71xx_hw_enable(ag);
-	if (ndev->phydev->link)
-		ag71xx_link_adjust(ag, false);
+
+	phylink_stop(ag->phylink);
+	phylink_start(ag->phylink);
+
 	rtnl_unlock();
 }
 
@@ -1768,6 +1793,12 @@ static int ag71xx_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, ndev);
 
+	err = ag71xx_phy_setup(ag);
+	if (err) {
+		netif_err(ag, probe, ndev, "failed to setup phy (%d)\n", err);
+		goto err_mdio_remove;
+	}
+
 	err = register_netdev(ndev);
 	if (err) {
 		netif_err(ag, probe, ndev, "unable to register net device\n");
-- 
2.24.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v6 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation
  2019-12-17  7:23 [PATCH v6 0/5] add dsa switch support for ar9331 Oleksij Rempel
  2019-12-17  7:23 ` [PATCH v6 1/5] net: ag71xx: port to phylink Oleksij Rempel
@ 2019-12-17  7:23 ` Oleksij Rempel
  2019-12-18 20:09   ` Rob Herring
  2019-12-17  7:23 ` [PATCH v6 3/5] MIPS: ath79: ar9331: add ar9331-switch node Oleksij Rempel
                   ` (2 subsequent siblings)
  4 siblings, 1 reply; 8+ messages in thread
From: Oleksij Rempel @ 2019-12-17  7:23 UTC (permalink / raw)
  To: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Rob Herring, Vivien Didelot
  Cc: Oleksij Rempel, Pengutronix Kernel Team, David S. Miller, netdev,
	linux-kernel, devicetree, linux-mips, Russell King

Atheros AR9331 has built-in 5 port switch. The switch can be configured
to use all 5 or 4 ports. One of built-in PHYs can be used by first built-in
ethernet controller or to be used directly by the switch over second ethernet
controller.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../devicetree/bindings/net/dsa/ar9331.txt    | 148 ++++++++++++++++++
 1 file changed, 148 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/ar9331.txt

diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt
new file mode 100644
index 000000000000..3d7b346c029a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt
@@ -0,0 +1,148 @@
+Atheros AR9331 built-in switch
+=============================
+
+It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal
+MDIO bus. All PHYs are built-in as well.
+
+Required properties:
+
+ - compatible: should be: "qca,ar9331-switch" 
+ - reg: Address on the MII bus for the switch.
+ - resets : Must contain an entry for each entry in reset-names.
+ - reset-names : Must include the following entries: "switch"
+ - interrupt-parent: Phandle to the parent interrupt controller
+ - interrupts: IRQ line for the switch
+ - interrupt-controller: Indicates the switch is itself an interrupt
+   controller. This is used for the PHY interrupts.
+ - #interrupt-cells: must be 1
+ - mdio: Container of PHY and devices on the switches MDIO bus.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+Examples:
+
+eth0: ethernet@19000000 {
+	compatible = "qca,ar9330-eth";
+	reg = <0x19000000 0x200>;
+	interrupts = <4>;
+
+	resets = <&rst 9>, <&rst 22>;
+	reset-names = "mac", "mdio";
+	clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+	clock-names = "eth", "mdio";
+
+	phy-mode = "mii";
+	phy-handle = <&phy_port4>;
+};
+
+eth1: ethernet@1a000000 {
+	compatible = "qca,ar9330-eth";
+	reg = <0x1a000000 0x200>;
+	interrupts = <5>;
+	resets = <&rst 13>, <&rst 23>;
+	reset-names = "mac", "mdio";
+	clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+	clock-names = "eth", "mdio";
+
+	phy-mode = "gmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch10: switch@10 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			compatible = "qca,ar9331-switch";
+			reg = <0x10>;
+			resets = <&rst 8>;
+			reset-names = "switch";
+
+			interrupt-parent = <&miscintc>;
+			interrupts = <12>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch_port0: port@0 {
+					reg = <0x0>;
+					label = "cpu";
+					ethernet = <&eth1>;
+
+					phy-mode = "gmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				switch_port1: port@1 {
+					reg = <0x1>;
+					phy-handle = <&phy_port0>;
+					phy-mode = "internal";
+				};
+
+				switch_port2: port@2 {
+					reg = <0x2>;
+					phy-handle = <&phy_port1>;
+					phy-mode = "internal";
+				};
+
+				switch_port3: port@3 {
+					reg = <0x3>;
+					phy-handle = <&phy_port2>;
+					phy-mode = "internal";
+				};
+
+				switch_port4: port@4 {
+					reg = <0x4>;
+					phy-handle = <&phy_port3>;
+					phy-mode = "internal";
+				};
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				interrupt-parent = <&switch10>;
+
+				phy_port0: phy@0 {
+					reg = <0x0>;
+					interrupts = <0>;
+				};
+
+				phy_port1: phy@1 {
+					reg = <0x1>;
+					interrupts = <0>;
+				};
+
+				phy_port2: phy@2 {
+					reg = <0x2>;
+					interrupts = <0>;
+				};
+
+				phy_port3: phy@3 {
+					reg = <0x3>;
+					interrupts = <0>;
+				};
+
+				phy_port4: phy@4 {
+					reg = <0x4>;
+					interrupts = <0>;
+				};
+			};
+		};
+	};
+};
-- 
2.24.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v6 3/5] MIPS: ath79: ar9331: add ar9331-switch node
  2019-12-17  7:23 [PATCH v6 0/5] add dsa switch support for ar9331 Oleksij Rempel
  2019-12-17  7:23 ` [PATCH v6 1/5] net: ag71xx: port to phylink Oleksij Rempel
  2019-12-17  7:23 ` [PATCH v6 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation Oleksij Rempel
@ 2019-12-17  7:23 ` Oleksij Rempel
  2019-12-17  7:23 ` [PATCH v6 4/5] net: dsa: add support for Atheros AR9331 TAG format Oleksij Rempel
  2019-12-17  7:23 ` [PATCH v6 5/5] net: dsa: add support for Atheros AR9331 built-in switch Oleksij Rempel
  4 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2019-12-17  7:23 UTC (permalink / raw)
  To: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Rob Herring, Vivien Didelot
  Cc: Oleksij Rempel, Pengutronix Kernel Team, David S. Miller, netdev,
	linux-kernel, devicetree, linux-mips, Russell King

Add switch node supported by dsa ar9331 driver.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/mips/boot/dts/qca/ar9331.dtsi           | 119 ++++++++++++++++++-
 arch/mips/boot/dts/qca/ar9331_dpt_module.dts |  13 ++
 2 files changed, 131 insertions(+), 1 deletion(-)

diff --git a/arch/mips/boot/dts/qca/ar9331.dtsi b/arch/mips/boot/dts/qca/ar9331.dtsi
index 5cfc9d347826..8f5aed760abb 100644
--- a/arch/mips/boot/dts/qca/ar9331.dtsi
+++ b/arch/mips/boot/dts/qca/ar9331.dtsi
@@ -126,6 +126,9 @@ eth0: ethernet@19000000 {
 			clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
 			clock-names = "eth", "mdio";
 
+			phy-mode = "mii";
+			phy-handle = <&phy_port4>;
+
 			status = "disabled";
 		};
 
@@ -133,13 +136,127 @@ eth1: ethernet@1a000000 {
 			compatible = "qca,ar9330-eth";
 			reg = <0x1a000000 0x200>;
 			interrupts = <5>;
-
 			resets = <&rst 13>, <&rst 23>;
 			reset-names = "mac", "mdio";
 			clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
 			clock-names = "eth", "mdio";
 
+			phy-mode = "gmii";
+
 			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch10: switch@10 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compatible = "qca,ar9331-switch";
+					reg = <0x10>;
+					resets = <&rst 8>;
+					reset-names = "switch";
+
+					interrupt-parent = <&miscintc>;
+					interrupts = <12>;
+
+					interrupt-controller;
+					#interrupt-cells = <1>;
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						switch_port0: port@0 {
+							reg = <0x0>;
+							label = "cpu";
+							ethernet = <&eth1>;
+
+							phy-mode = "gmii";
+
+							fixed-link {
+								speed = <1000>;
+								full-duplex;
+							};
+						};
+
+						switch_port1: port@1 {
+							reg = <0x1>;
+							phy-handle = <&phy_port0>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+
+						switch_port2: port@2 {
+							reg = <0x2>;
+							phy-handle = <&phy_port1>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+
+						switch_port3: port@3 {
+							reg = <0x3>;
+							phy-handle = <&phy_port2>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+
+						switch_port4: port@4 {
+							reg = <0x4>;
+							phy-handle = <&phy_port3>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+					};
+
+					mdio {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						interrupt-parent = <&switch10>;
+
+						phy_port0: phy@0 {
+							reg = <0x0>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port1: phy@1 {
+							reg = <0x1>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port2: phy@2 {
+							reg = <0x2>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port3: phy@3 {
+							reg = <0x3>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port4: phy@4 {
+							reg = <0x4>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+					};
+				};
+			};
 		};
 
 		usb: usb@1b000100 {
diff --git a/arch/mips/boot/dts/qca/ar9331_dpt_module.dts b/arch/mips/boot/dts/qca/ar9331_dpt_module.dts
index 77bab823eb3b..0f2b20044834 100644
--- a/arch/mips/boot/dts/qca/ar9331_dpt_module.dts
+++ b/arch/mips/boot/dts/qca/ar9331_dpt_module.dts
@@ -84,3 +84,16 @@ &eth0 {
 &eth1 {
 	status = "okay";
 };
+
+&switch_port1 {
+	label = "lan0";
+	status = "okay";
+};
+
+&phy_port0 {
+	status = "okay";
+};
+
+&phy_port4 {
+	status = "okay";
+};
-- 
2.24.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v6 4/5] net: dsa: add support for Atheros AR9331 TAG format
  2019-12-17  7:23 [PATCH v6 0/5] add dsa switch support for ar9331 Oleksij Rempel
                   ` (2 preceding siblings ...)
  2019-12-17  7:23 ` [PATCH v6 3/5] MIPS: ath79: ar9331: add ar9331-switch node Oleksij Rempel
@ 2019-12-17  7:23 ` Oleksij Rempel
  2019-12-17  7:23 ` [PATCH v6 5/5] net: dsa: add support for Atheros AR9331 built-in switch Oleksij Rempel
  4 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2019-12-17  7:23 UTC (permalink / raw)
  To: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Rob Herring, Vivien Didelot
  Cc: Oleksij Rempel, Pengutronix Kernel Team, David S. Miller, netdev,
	linux-kernel, devicetree, linux-mips, Russell King

Add support for tag format used in Atheros AR9331 built-in switch.

Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 include/net/dsa.h    |  2 +
 net/dsa/Kconfig      |  6 +++
 net/dsa/Makefile     |  1 +
 net/dsa/tag_ar9331.c | 96 ++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 105 insertions(+)
 create mode 100644 net/dsa/tag_ar9331.c

diff --git a/include/net/dsa.h b/include/net/dsa.h
index 6767dc3f66c0..da5578db228e 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -43,6 +43,7 @@ struct phylink_link_state;
 #define DSA_TAG_PROTO_SJA1105_VALUE		13
 #define DSA_TAG_PROTO_KSZ8795_VALUE		14
 #define DSA_TAG_PROTO_OCELOT_VALUE		15
+#define DSA_TAG_PROTO_AR9331_VALUE		16
 
 enum dsa_tag_protocol {
 	DSA_TAG_PROTO_NONE		= DSA_TAG_PROTO_NONE_VALUE,
@@ -61,6 +62,7 @@ enum dsa_tag_protocol {
 	DSA_TAG_PROTO_SJA1105		= DSA_TAG_PROTO_SJA1105_VALUE,
 	DSA_TAG_PROTO_KSZ8795		= DSA_TAG_PROTO_KSZ8795_VALUE,
 	DSA_TAG_PROTO_OCELOT		= DSA_TAG_PROTO_OCELOT_VALUE,
+	DSA_TAG_PROTO_AR9331		= DSA_TAG_PROTO_AR9331_VALUE,
 };
 
 struct packet_type;
diff --git a/net/dsa/Kconfig b/net/dsa/Kconfig
index 1e6c3cac11e6..92663dcb3aa2 100644
--- a/net/dsa/Kconfig
+++ b/net/dsa/Kconfig
@@ -29,6 +29,12 @@ config NET_DSA_TAG_8021Q
 
 	  Drivers which use these helpers should select this as dependency.
 
+config NET_DSA_TAG_AR9331
+	tristate "Tag driver for Atheros AR9331 SoC with built-in switch"
+	help
+	  Say Y or M if you want to enable support for tagging frames for
+	  the Atheros AR9331 SoC with built-in switch.
+
 config NET_DSA_TAG_BRCM_COMMON
 	tristate
 	default n
diff --git a/net/dsa/Makefile b/net/dsa/Makefile
index 9a482c38bdb1..108486cfdeef 100644
--- a/net/dsa/Makefile
+++ b/net/dsa/Makefile
@@ -5,6 +5,7 @@ dsa_core-y += dsa.o dsa2.o master.o port.o slave.o switch.o
 
 # tagging formats
 obj-$(CONFIG_NET_DSA_TAG_8021Q) += tag_8021q.o
+obj-$(CONFIG_NET_DSA_TAG_AR9331) += tag_ar9331.o
 obj-$(CONFIG_NET_DSA_TAG_BRCM_COMMON) += tag_brcm.o
 obj-$(CONFIG_NET_DSA_TAG_DSA) += tag_dsa.o
 obj-$(CONFIG_NET_DSA_TAG_EDSA) += tag_edsa.o
diff --git a/net/dsa/tag_ar9331.c b/net/dsa/tag_ar9331.c
new file mode 100644
index 000000000000..466ffa92a474
--- /dev/null
+++ b/net/dsa/tag_ar9331.c
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
+ */
+
+
+#include <linux/bitfield.h>
+#include <linux/etherdevice.h>
+
+#include "dsa_priv.h"
+
+#define AR9331_HDR_LEN			2
+#define AR9331_HDR_VERSION		1
+
+#define AR9331_HDR_VERSION_MASK		GENMASK(15, 14)
+#define AR9331_HDR_PRIORITY_MASK	GENMASK(13, 12)
+#define AR9331_HDR_TYPE_MASK		GENMASK(10, 8)
+#define AR9331_HDR_BROADCAST		BIT(7)
+#define AR9331_HDR_FROM_CPU		BIT(6)
+/* AR9331_HDR_RESERVED - not used or may be version field.
+ * According to the AR8216 doc it should 0b10. On AR9331 it is 0b11 on RX path
+ * and should be set to 0b11 to make it work.
+ */
+#define AR9331_HDR_RESERVED_MASK	GENMASK(5, 4)
+#define AR9331_HDR_PORT_NUM_MASK	GENMASK(3, 0)
+
+static struct sk_buff *ar9331_tag_xmit(struct sk_buff *skb,
+				       struct net_device *dev)
+{
+	struct dsa_port *dp = dsa_slave_to_port(dev);
+	__le16 *phdr;
+	u16 hdr;
+
+	if (skb_cow_head(skb, 0) < 0)
+		return NULL;
+
+	phdr = skb_push(skb, AR9331_HDR_LEN);
+
+	hdr = FIELD_PREP(AR9331_HDR_VERSION_MASK, AR9331_HDR_VERSION);
+	hdr |= AR9331_HDR_FROM_CPU | dp->index;
+	/* 0b10 for AR8216 and 0b11 for AR9331 */
+	hdr |= AR9331_HDR_RESERVED_MASK;
+
+	phdr[0] = cpu_to_le16(hdr);
+
+	return skb;
+}
+
+static struct sk_buff *ar9331_tag_rcv(struct sk_buff *skb,
+				      struct net_device *ndev,
+				      struct packet_type *pt)
+{
+	u8 ver, port;
+	u16 hdr;
+
+	if (unlikely(!pskb_may_pull(skb, AR9331_HDR_LEN)))
+		return NULL;
+
+	hdr = le16_to_cpu(*(__le16 *)skb_mac_header(skb));
+
+	ver = FIELD_GET(AR9331_HDR_VERSION_MASK, hdr);
+	if (unlikely(ver != AR9331_HDR_VERSION)) {
+		netdev_warn_once(ndev, "%s:%i wrong header version 0x%2x\n",
+				 __func__, __LINE__, hdr);
+		return NULL;
+	}
+
+	if (unlikely(hdr & AR9331_HDR_FROM_CPU)) {
+		netdev_warn_once(ndev, "%s:%i packet should not be from cpu 0x%2x\n",
+				 __func__, __LINE__, hdr);
+		return NULL;
+	}
+
+	skb_pull_rcsum(skb, AR9331_HDR_LEN);
+
+	/* Get source port information */
+	port = FIELD_GET(AR9331_HDR_PORT_NUM_MASK, hdr);
+
+	skb->dev = dsa_master_find_slave(ndev, 0, port);
+	if (!skb->dev)
+		return NULL;
+
+	return skb;
+}
+
+static const struct dsa_device_ops ar9331_netdev_ops = {
+	.name	= "ar9331",
+	.proto	= DSA_TAG_PROTO_AR9331,
+	.xmit	= ar9331_tag_xmit,
+	.rcv	= ar9331_tag_rcv,
+	.overhead = AR9331_HDR_LEN,
+};
+
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_AR9331);
+module_dsa_tag_driver(ar9331_netdev_ops);
-- 
2.24.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH v6 5/5] net: dsa: add support for Atheros AR9331 built-in switch
  2019-12-17  7:23 [PATCH v6 0/5] add dsa switch support for ar9331 Oleksij Rempel
                   ` (3 preceding siblings ...)
  2019-12-17  7:23 ` [PATCH v6 4/5] net: dsa: add support for Atheros AR9331 TAG format Oleksij Rempel
@ 2019-12-17  7:23 ` Oleksij Rempel
  4 siblings, 0 replies; 8+ messages in thread
From: Oleksij Rempel @ 2019-12-17  7:23 UTC (permalink / raw)
  To: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Rob Herring, Vivien Didelot
  Cc: Oleksij Rempel, Pengutronix Kernel Team, David S. Miller, netdev,
	linux-kernel, devicetree, linux-mips, Russell King

Provide basic support for Atheros AR9331 built-in switch. So far it
works as port multiplexer without any hardware offloading support.

Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/dsa/Kconfig      |   2 +
 drivers/net/dsa/Makefile     |   1 +
 drivers/net/dsa/qca/Kconfig  |  11 +
 drivers/net/dsa/qca/Makefile |   2 +
 drivers/net/dsa/qca/ar9331.c | 817 +++++++++++++++++++++++++++++++++++
 5 files changed, 833 insertions(+)
 create mode 100644 drivers/net/dsa/qca/Kconfig
 create mode 100644 drivers/net/dsa/qca/Makefile
 create mode 100644 drivers/net/dsa/qca/ar9331.c

diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index c7667645f04a..cbd74a72d0a1 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -54,6 +54,8 @@ source "drivers/net/dsa/mv88e6xxx/Kconfig"
 
 source "drivers/net/dsa/ocelot/Kconfig"
 
+source "drivers/net/dsa/qca/Kconfig"
+
 source "drivers/net/dsa/sja1105/Kconfig"
 
 config NET_DSA_QCA8K
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index 9d384a32b3a2..4a943ccc2ca4 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -21,4 +21,5 @@ obj-y				+= b53/
 obj-y				+= microchip/
 obj-y				+= mv88e6xxx/
 obj-y				+= ocelot/
+obj-y				+= qca/
 obj-y				+= sja1105/
diff --git a/drivers/net/dsa/qca/Kconfig b/drivers/net/dsa/qca/Kconfig
new file mode 100644
index 000000000000..8bdc9adffdba
--- /dev/null
+++ b/drivers/net/dsa/qca/Kconfig
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config NET_DSA_AR9331
+	tristate "Qualcomm Atheros AR9331 Ethernet switch support"
+	depends on NET_DSA
+	select NET_DSA_TAG_AR9331
+	select REGMAP
+	---help---
+	  This enables support for the Qualcomm Atheros AR9331 built-in Ethernet
+	  switch.
+
+
diff --git a/drivers/net/dsa/qca/Makefile b/drivers/net/dsa/qca/Makefile
new file mode 100644
index 000000000000..274022319066
--- /dev/null
+++ b/drivers/net/dsa/qca/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_NET_DSA_AR9331)	+= ar9331.o
diff --git a/drivers/net/dsa/qca/ar9331.c b/drivers/net/dsa/qca/ar9331.c
new file mode 100644
index 000000000000..7ab8a6649104
--- /dev/null
+++ b/drivers/net/dsa/qca/ar9331.c
@@ -0,0 +1,817 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2019 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
+
+#include <linux/bitfield.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_mdio.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <net/dsa.h>
+
+#define AR9331_SW_NAME				"ar9331_switch"
+#define AR9331_SW_PORTS				6
+
+/* dummy reg to change page */
+#define AR9331_SW_REG_PAGE			BIT(18)
+
+/* Global Interrupt */
+#define AR9331_SW_REG_GINT			0x10
+#define AR9331_SW_REG_GINT_MASK			0x14
+#define AR9331_SW_GINT_PHY_INT			BIT(2)
+
+#define AR9331_SW_REG_FLOOD_MASK		0x2c
+#define AR9331_SW_FLOOD_MASK_BROAD_TO_CPU	BIT(26)
+
+#define AR9331_SW_REG_GLOBAL_CTRL		0x30
+#define AR9331_SW_GLOBAL_CTRL_MFS_M		GENMASK(13, 0)
+
+#define AR9331_SW_REG_MDIO_CTRL			0x98
+#define AR9331_SW_MDIO_CTRL_BUSY		BIT(31)
+#define AR9331_SW_MDIO_CTRL_MASTER_EN		BIT(30)
+#define AR9331_SW_MDIO_CTRL_CMD_READ		BIT(27)
+#define AR9331_SW_MDIO_CTRL_PHY_ADDR_M		GENMASK(25, 21)
+#define AR9331_SW_MDIO_CTRL_REG_ADDR_M		GENMASK(20, 16)
+#define AR9331_SW_MDIO_CTRL_DATA_M		GENMASK(16, 0)
+
+#define AR9331_SW_REG_PORT_STATUS(_port)	(0x100 + (_port) * 0x100)
+
+/* FLOW_LINK_EN - enable mac flow control config auto-neg with phy.
+ * If not set, mac can be config by software.
+ */
+#define AR9331_SW_PORT_STATUS_FLOW_LINK_EN	BIT(12)
+
+/* LINK_EN - If set, MAC is configured from PHY link status.
+ * If not set, MAC should be configured by software.
+ */
+#define AR9331_SW_PORT_STATUS_LINK_EN		BIT(9)
+#define AR9331_SW_PORT_STATUS_DUPLEX_MODE	BIT(6)
+#define AR9331_SW_PORT_STATUS_RX_FLOW_EN	BIT(5)
+#define AR9331_SW_PORT_STATUS_TX_FLOW_EN	BIT(4)
+#define AR9331_SW_PORT_STATUS_RXMAC		BIT(3)
+#define AR9331_SW_PORT_STATUS_TXMAC		BIT(2)
+#define AR9331_SW_PORT_STATUS_SPEED_M		GENMASK(1, 0)
+#define AR9331_SW_PORT_STATUS_SPEED_1000	2
+#define AR9331_SW_PORT_STATUS_SPEED_100		1
+#define AR9331_SW_PORT_STATUS_SPEED_10		0
+
+#define AR9331_SW_PORT_STATUS_MAC_MASK \
+	(AR9331_SW_PORT_STATUS_TXMAC | AR9331_SW_PORT_STATUS_RXMAC)
+
+#define AR9331_SW_PORT_STATUS_LINK_MASK \
+	(AR9331_SW_PORT_STATUS_LINK_EN | AR9331_SW_PORT_STATUS_FLOW_LINK_EN | \
+	 AR9331_SW_PORT_STATUS_DUPLEX_MODE | \
+	 AR9331_SW_PORT_STATUS_RX_FLOW_EN | AR9331_SW_PORT_STATUS_TX_FLOW_EN | \
+	 AR9331_SW_PORT_STATUS_SPEED_M)
+
+/* Phy bypass mode
+ * ------------------------------------------------------------------------
+ * Bit:   | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 |
+ *
+ * real   | start |   OP  | PhyAddr           |  Reg Addr         |  TA   |
+ * atheros| start |   OP  | 2'b00 |PhyAdd[2:0]|  Reg Addr[4:0]    |  TA   |
+ *
+ *
+ * Bit:   |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 |
+ * real   |  Data                                                         |
+ * atheros|  Data                                                         |
+ *
+ * ------------------------------------------------------------------------
+ * Page address mode
+ * ------------------------------------------------------------------------
+ * Bit:   | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 |
+ * real   | start |   OP  | PhyAddr           |  Reg Addr         |  TA   |
+ * atheros| start |   OP  | 2'b11 |                          8'b0 |  TA   |
+ *
+ * Bit:   |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 |
+ * real   |  Data                                                         |
+ * atheros|                       | Page [9:0]                            |
+ */
+/* In case of Page Address mode, Bit[18:9] of 32 bit register address should be
+ * written to bits[9:0] of mdio data register.
+ */
+#define AR9331_SW_ADDR_PAGE			GENMASK(18, 9)
+
+/* ------------------------------------------------------------------------
+ * Normal register access mode
+ * ------------------------------------------------------------------------
+ * Bit:   | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 |
+ * real   | start |   OP  | PhyAddr           |  Reg Addr         |  TA   |
+ * atheros| start |   OP  | 2'b10 |  low_addr[7:0]                |  TA   |
+ *
+ * Bit:   |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 |
+ * real   |  Data                                                         |
+ * atheros|  Data                                                         |
+ * ------------------------------------------------------------------------
+ */
+#define AR9331_SW_LOW_ADDR_PHY			GENMASK(8, 6)
+#define AR9331_SW_LOW_ADDR_REG			GENMASK(5, 1)
+
+#define AR9331_SW_MDIO_PHY_MODE_M		GENMASK(4, 3)
+#define AR9331_SW_MDIO_PHY_MODE_PAGE		3
+#define AR9331_SW_MDIO_PHY_MODE_REG		2
+#define AR9331_SW_MDIO_PHY_MODE_BYPASS		0
+#define AR9331_SW_MDIO_PHY_ADDR_M		GENMASK(2, 0)
+
+/* Empirical determined values */
+#define AR9331_SW_MDIO_POLL_SLEEP_US		1
+#define AR9331_SW_MDIO_POLL_TIMEOUT_US		20
+
+struct ar9331_sw_priv {
+	struct device *dev;
+	struct dsa_switch ds;
+	struct dsa_switch_ops ops;
+	struct irq_domain *irqdomain;
+	struct mii_bus *mbus; /* mdio master */
+	struct mii_bus *sbus; /* mdio slave */
+	struct regmap *regmap;
+	struct reset_control *sw_reset;
+};
+
+/* Warning: switch reset will reset last AR9331_SW_MDIO_PHY_MODE_PAGE request
+ * If some kind of optimization is used, the request should be repeated.
+ */
+static int ar9331_sw_reset(struct ar9331_sw_priv *priv)
+{
+	int ret;
+
+	ret = reset_control_assert(priv->sw_reset);
+	if (ret)
+		goto error;
+
+	/* AR9331 doc do not provide any information about proper reset
+	 * sequence. The AR8136 (the closes switch to the AR9331) doc says:
+	 * reset duration should be greater than 10ms. So, let's use this value
+	 * for now.
+	 */
+	usleep_range(10000, 15000);
+	ret = reset_control_deassert(priv->sw_reset);
+	if (ret)
+		goto error;
+	/* There is no information on how long should we wait after reset.
+	 * AR8136 has an EEPROM and there is an Interrupt for EEPROM load
+	 * status. AR9331 has no EEPROM support.
+	 * For now, do not wait. In case AR8136 will be needed, the after
+	 * reset delay can be added as well.
+	 */
+
+	return 0;
+error:
+	dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+	return ret;
+}
+
+static int ar9331_sw_mbus_write(struct mii_bus *mbus, int port, int regnum,
+				u16 data)
+{
+	struct ar9331_sw_priv *priv = mbus->priv;
+	struct regmap *regmap = priv->regmap;
+	u32 val;
+	int ret;
+
+	ret = regmap_write(regmap, AR9331_SW_REG_MDIO_CTRL,
+			   AR9331_SW_MDIO_CTRL_BUSY |
+			   AR9331_SW_MDIO_CTRL_MASTER_EN |
+			   FIELD_PREP(AR9331_SW_MDIO_CTRL_PHY_ADDR_M, port) |
+			   FIELD_PREP(AR9331_SW_MDIO_CTRL_REG_ADDR_M, regnum) |
+			   FIELD_PREP(AR9331_SW_MDIO_CTRL_DATA_M, data));
+	if (ret)
+		goto error;
+
+	ret = regmap_read_poll_timeout(regmap, AR9331_SW_REG_MDIO_CTRL, val,
+				       !(val & AR9331_SW_MDIO_CTRL_BUSY),
+				       AR9331_SW_MDIO_POLL_SLEEP_US,
+				       AR9331_SW_MDIO_POLL_TIMEOUT_US);
+	if (ret)
+		goto error;
+
+	return 0;
+error:
+	dev_err_ratelimited(priv->dev, "PHY write error: %i\n", ret);
+	return ret;
+}
+
+static int ar9331_sw_mbus_read(struct mii_bus *mbus, int port, int regnum)
+{
+	struct ar9331_sw_priv *priv = mbus->priv;
+	struct regmap *regmap = priv->regmap;
+	u32 val;
+	int ret;
+
+	ret = regmap_write(regmap, AR9331_SW_REG_MDIO_CTRL,
+			   AR9331_SW_MDIO_CTRL_BUSY |
+			   AR9331_SW_MDIO_CTRL_MASTER_EN |
+			   AR9331_SW_MDIO_CTRL_CMD_READ |
+			   FIELD_PREP(AR9331_SW_MDIO_CTRL_PHY_ADDR_M, port) |
+			   FIELD_PREP(AR9331_SW_MDIO_CTRL_REG_ADDR_M, regnum));
+	if (ret)
+		goto error;
+
+	ret = regmap_read_poll_timeout(regmap, AR9331_SW_REG_MDIO_CTRL, val,
+				       !(val & AR9331_SW_MDIO_CTRL_BUSY),
+				       AR9331_SW_MDIO_POLL_SLEEP_US,
+				       AR9331_SW_MDIO_POLL_TIMEOUT_US);
+	if (ret)
+		goto error;
+
+	ret = regmap_read(regmap, AR9331_SW_REG_MDIO_CTRL, &val);
+	if (ret)
+		goto error;
+
+	return FIELD_GET(AR9331_SW_MDIO_CTRL_DATA_M, val);
+
+error:
+	dev_err_ratelimited(priv->dev, "PHY read error: %i\n", ret);
+	return ret;
+}
+
+static int ar9331_sw_mbus_init(struct ar9331_sw_priv *priv)
+{
+	struct device *dev = priv->dev;
+	static struct mii_bus *mbus;
+	struct device_node *np, *mnp;
+	int ret;
+
+	np = dev->of_node;
+
+	mbus = devm_mdiobus_alloc(dev);
+	if (!mbus)
+		return -ENOMEM;
+
+	mbus->name = np->full_name;
+	snprintf(mbus->id, MII_BUS_ID_SIZE, "%pOF", np);
+
+	mbus->read = ar9331_sw_mbus_read;
+	mbus->write = ar9331_sw_mbus_write;
+	mbus->priv = priv;
+	mbus->parent = dev;
+
+	mnp = of_get_child_by_name(np, "mdio");
+	if (!mnp)
+		return -ENODEV;
+
+	ret = of_mdiobus_register(mbus, mnp);
+	of_node_put(mnp);
+	if (ret)
+		return ret;
+
+	priv->mbus = mbus;
+
+	return 0;
+}
+
+static int ar9331_sw_setup(struct dsa_switch *ds)
+{
+	struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+	struct regmap *regmap = priv->regmap;
+	int ret;
+
+	ret = ar9331_sw_reset(priv);
+	if (ret)
+		return ret;
+
+	/* Reset will set proper defaults. CPU - Port0 will be enabled and
+	 * configured. All other ports (ports 1 - 5) are disabled
+	 */
+	ret = ar9331_sw_mbus_init(priv);
+	if (ret)
+		return ret;
+
+	/* Do not drop broadcast frames */
+	ret = regmap_write_bits(regmap, AR9331_SW_REG_FLOOD_MASK,
+				AR9331_SW_FLOOD_MASK_BROAD_TO_CPU,
+				AR9331_SW_FLOOD_MASK_BROAD_TO_CPU);
+	if (ret)
+		goto error;
+
+	/* Set max frame size to the maximum supported value */
+	ret = regmap_write_bits(regmap, AR9331_SW_REG_GLOBAL_CTRL,
+				AR9331_SW_GLOBAL_CTRL_MFS_M,
+				AR9331_SW_GLOBAL_CTRL_MFS_M);
+	if (ret)
+		goto error;
+
+	return 0;
+error:
+	dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+	return ret;
+}
+
+static void ar9331_sw_port_disable(struct dsa_switch *ds, int port)
+{
+	struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+	struct regmap *regmap = priv->regmap;
+	int ret;
+
+	ret = regmap_write(regmap, AR9331_SW_REG_PORT_STATUS(port), 0);
+	if (ret)
+		dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static enum dsa_tag_protocol ar9331_sw_get_tag_protocol(struct dsa_switch *ds,
+							int port)
+{
+	return DSA_TAG_PROTO_AR9331;
+}
+
+static void ar9331_sw_phylink_validate(struct dsa_switch *ds, int port,
+				       unsigned long *supported,
+				       struct phylink_link_state *state)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+	switch (port) {
+	case 0:
+		if (state->interface != PHY_INTERFACE_MODE_GMII)
+			goto unsupported;
+
+		phylink_set(mask, 1000baseT_Full);
+		phylink_set(mask, 1000baseT_Half);
+		break;
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+	case 5:
+		if (state->interface != PHY_INTERFACE_MODE_INTERNAL)
+			goto unsupported;
+		break;
+	default:
+		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+		dev_err(ds->dev, "Unsupported port: %i\n", port);
+		return;
+	}
+
+	phylink_set_port_modes(mask);
+	phylink_set(mask, Pause);
+	phylink_set(mask, Asym_Pause);
+
+	phylink_set(mask, 10baseT_Half);
+	phylink_set(mask, 10baseT_Full);
+	phylink_set(mask, 100baseT_Half);
+	phylink_set(mask, 100baseT_Full);
+
+	bitmap_and(supported, supported, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+	bitmap_and(state->advertising, state->advertising, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+
+	return;
+
+unsupported:
+	bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+	dev_err(ds->dev, "Unsupported interface: %d, port: %d\n",
+		state->interface, port);
+}
+
+static void ar9331_sw_phylink_mac_config(struct dsa_switch *ds, int port,
+					 unsigned int mode,
+					 const struct phylink_link_state *state)
+{
+	struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+	struct regmap *regmap = priv->regmap;
+	int ret;
+	u32 val;
+
+	switch (state->speed) {
+	case SPEED_1000:
+		val = AR9331_SW_PORT_STATUS_SPEED_1000;
+		break;
+	case SPEED_100:
+		val = AR9331_SW_PORT_STATUS_SPEED_100;
+		break;
+	case SPEED_10:
+		val = AR9331_SW_PORT_STATUS_SPEED_10;
+		break;
+	default:
+		return;
+	}
+
+	if (state->duplex)
+		val |= AR9331_SW_PORT_STATUS_DUPLEX_MODE;
+
+	if (state->pause & MLO_PAUSE_TX)
+		val |= AR9331_SW_PORT_STATUS_TX_FLOW_EN;
+
+	if (state->pause & MLO_PAUSE_RX)
+		val |= AR9331_SW_PORT_STATUS_RX_FLOW_EN;
+
+	ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port),
+				 AR9331_SW_PORT_STATUS_LINK_MASK, val);
+	if (ret)
+		dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static void ar9331_sw_phylink_mac_link_down(struct dsa_switch *ds, int port,
+					    unsigned int mode,
+					    phy_interface_t interface)
+{
+	struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+	struct regmap *regmap = priv->regmap;
+	int ret;
+
+	ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port),
+				 AR9331_SW_PORT_STATUS_MAC_MASK, 0);
+	if (ret)
+		dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static void ar9331_sw_phylink_mac_link_up(struct dsa_switch *ds, int port,
+					  unsigned int mode,
+					  phy_interface_t interface,
+					  struct phy_device *phydev)
+{
+	struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv;
+	struct regmap *regmap = priv->regmap;
+	int ret;
+
+	ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port),
+				 AR9331_SW_PORT_STATUS_MAC_MASK,
+				 AR9331_SW_PORT_STATUS_MAC_MASK);
+	if (ret)
+		dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret);
+}
+
+static const struct dsa_switch_ops ar9331_sw_ops = {
+	.get_tag_protocol	= ar9331_sw_get_tag_protocol,
+	.setup			= ar9331_sw_setup,
+	.port_disable		= ar9331_sw_port_disable,
+	.phylink_validate	= ar9331_sw_phylink_validate,
+	.phylink_mac_config	= ar9331_sw_phylink_mac_config,
+	.phylink_mac_link_down	= ar9331_sw_phylink_mac_link_down,
+	.phylink_mac_link_up	= ar9331_sw_phylink_mac_link_up,
+};
+
+static irqreturn_t ar9331_sw_irq(int irq, void *data)
+{
+	struct ar9331_sw_priv *priv = data;
+	struct regmap *regmap = priv->regmap;
+	u32 stat;
+	int ret;
+
+	ret = regmap_read(regmap, AR9331_SW_REG_GINT, &stat);
+	if (ret) {
+		dev_err(priv->dev, "can't read interrupt status\n");
+		return IRQ_NONE;
+	}
+
+	if (!stat)
+		return IRQ_NONE;
+
+	if (stat & AR9331_SW_GINT_PHY_INT) {
+		int child_irq;
+
+		child_irq = irq_find_mapping(priv->irqdomain, 0);
+		handle_nested_irq(child_irq);
+	}
+
+	ret = regmap_write(regmap, AR9331_SW_REG_GINT, stat);
+	if (ret) {
+		dev_err(priv->dev, "can't write interrupt status\n");
+		return IRQ_NONE;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static void ar9331_sw_mask_irq(struct irq_data *d)
+{
+	struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d);
+	struct regmap *regmap = priv->regmap;
+	int ret;
+
+	ret = regmap_update_bits(regmap, AR9331_SW_REG_GINT_MASK,
+				 AR9331_SW_GINT_PHY_INT, 0);
+	if (ret)
+		dev_err(priv->dev, "could not mask IRQ\n");
+}
+
+static void ar9331_sw_unmask_irq(struct irq_data *d)
+{
+	struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d);
+	struct regmap *regmap = priv->regmap;
+	int ret;
+
+	ret = regmap_update_bits(regmap, AR9331_SW_REG_GINT_MASK,
+				 AR9331_SW_GINT_PHY_INT,
+				 AR9331_SW_GINT_PHY_INT);
+	if (ret)
+		dev_err(priv->dev, "could not unmask IRQ\n");
+}
+
+static struct irq_chip ar9331_sw_irq_chip = {
+	.name = AR9331_SW_NAME,
+	.irq_mask = ar9331_sw_mask_irq,
+	.irq_unmask = ar9331_sw_unmask_irq,
+};
+
+static int ar9331_sw_irq_map(struct irq_domain *domain, unsigned int irq,
+			     irq_hw_number_t hwirq)
+{
+	irq_set_chip_data(irq, domain->host_data);
+	irq_set_chip_and_handler(irq, &ar9331_sw_irq_chip, handle_simple_irq);
+	irq_set_nested_thread(irq, 1);
+	irq_set_noprobe(irq);
+
+	return 0;
+}
+
+static void ar9331_sw_irq_unmap(struct irq_domain *d, unsigned int irq)
+{
+	irq_set_nested_thread(irq, 0);
+	irq_set_chip_and_handler(irq, NULL, NULL);
+	irq_set_chip_data(irq, NULL);
+}
+
+static const struct irq_domain_ops ar9331_sw_irqdomain_ops = {
+	.map = ar9331_sw_irq_map,
+	.unmap = ar9331_sw_irq_unmap,
+	.xlate = irq_domain_xlate_onecell,
+};
+
+static int ar9331_sw_irq_init(struct ar9331_sw_priv *priv)
+{
+	struct device_node *np = priv->dev->of_node;
+	struct device *dev = priv->dev;
+	int ret, irq;
+
+	irq = of_irq_get(np, 0);
+	if (irq <= 0) {
+		dev_err(dev, "failed to get parent IRQ\n");
+		return irq ? irq : -EINVAL;
+	}
+
+	ret = devm_request_threaded_irq(dev, irq, NULL, ar9331_sw_irq,
+					IRQF_ONESHOT, AR9331_SW_NAME, priv);
+	if (ret) {
+		dev_err(dev, "unable to request irq: %d\n", ret);
+		return ret;
+	}
+
+	priv->irqdomain = irq_domain_add_linear(np, 1, &ar9331_sw_irqdomain_ops,
+						priv);
+	if (!priv->irqdomain) {
+		dev_err(dev, "failed to create IRQ domain\n");
+		return -EINVAL;
+	}
+
+	irq_set_parent(irq_create_mapping(priv->irqdomain, 0), irq);
+
+	return 0;
+}
+
+static int __ar9331_mdio_write(struct mii_bus *sbus, u8 mode, u16 reg, u16 val)
+{
+	u8 r, p;
+
+	p = FIELD_PREP(AR9331_SW_MDIO_PHY_MODE_M, mode) |
+		FIELD_GET(AR9331_SW_LOW_ADDR_PHY, reg);
+	r = FIELD_GET(AR9331_SW_LOW_ADDR_REG, reg);
+
+	return mdiobus_write(sbus, p, r, val);
+}
+
+static int __ar9331_mdio_read(struct mii_bus *sbus, u16 reg)
+{
+	u8 r, p;
+
+	p = FIELD_PREP(AR9331_SW_MDIO_PHY_MODE_M, AR9331_SW_MDIO_PHY_MODE_REG) |
+		FIELD_GET(AR9331_SW_LOW_ADDR_PHY, reg);
+	r = FIELD_GET(AR9331_SW_LOW_ADDR_REG, reg);
+
+	return mdiobus_read(sbus, p, r);
+}
+
+static int ar9331_mdio_read(void *ctx, const void *reg_buf, size_t reg_len,
+			    void *val_buf, size_t val_len)
+{
+	struct ar9331_sw_priv *priv = ctx;
+	struct mii_bus *sbus = priv->sbus;
+	u32 reg = *(u32 *)reg_buf;
+	int ret;
+
+	if (reg == AR9331_SW_REG_PAGE) {
+		/* We cannot read the page selector register from hardware and
+		 * we cache its value in regmap. Return all bits set here,
+		 * that regmap will always write the page on first use.
+		 */
+		*(u32 *)val_buf = GENMASK(9, 0);
+		return 0;
+	}
+
+	ret = __ar9331_mdio_read(sbus, reg);
+	if (ret < 0)
+		goto error;
+
+	*(u32 *)val_buf = ret;
+	ret = __ar9331_mdio_read(sbus, reg + 2);
+	if (ret < 0)
+		goto error;
+
+	*(u32 *)val_buf |= ret << 16;
+
+	return 0;
+error:
+	dev_err_ratelimited(&sbus->dev, "Bus error. Failed to read register.\n");
+	return ret;
+}
+
+static int ar9331_mdio_write(void *ctx, u32 reg, u32 val)
+{
+	struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ctx;
+	struct mii_bus *sbus = priv->sbus;
+	int ret;
+
+	if (reg == AR9331_SW_REG_PAGE) {
+		ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_PAGE,
+					  0, val);
+		if (ret < 0)
+			goto error;
+
+		return 0;
+	}
+
+	ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_REG, reg, val);
+	if (ret < 0)
+		goto error;
+
+	ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_REG, reg + 2,
+				  val >> 16);
+	if (ret < 0)
+		goto error;
+
+	return 0;
+error:
+	dev_err_ratelimited(&sbus->dev, "Bus error. Failed to write register.\n");
+	return ret;
+}
+
+static int ar9331_sw_bus_write(void *context, const void *data, size_t count)
+{
+	u32 reg = *(u32 *)data;
+	u32 val = *((u32 *)data + 1);
+
+	return ar9331_mdio_write(context, reg, val);
+}
+
+static const struct regmap_range ar9331_valid_regs[] = {
+	regmap_reg_range(0x0, 0x0),
+	regmap_reg_range(0x10, 0x14),
+	regmap_reg_range(0x20, 0x24),
+	regmap_reg_range(0x2c, 0x30),
+	regmap_reg_range(0x40, 0x44),
+	regmap_reg_range(0x50, 0x78),
+	regmap_reg_range(0x80, 0x98),
+
+	regmap_reg_range(0x100, 0x120),
+	regmap_reg_range(0x200, 0x220),
+	regmap_reg_range(0x300, 0x320),
+	regmap_reg_range(0x400, 0x420),
+	regmap_reg_range(0x500, 0x520),
+	regmap_reg_range(0x600, 0x620),
+
+	regmap_reg_range(0x20000, 0x200a4),
+	regmap_reg_range(0x20100, 0x201a4),
+	regmap_reg_range(0x20200, 0x202a4),
+	regmap_reg_range(0x20300, 0x203a4),
+	regmap_reg_range(0x20400, 0x204a4),
+	regmap_reg_range(0x20500, 0x205a4),
+
+	/* dummy page selector reg */
+	regmap_reg_range(AR9331_SW_REG_PAGE, AR9331_SW_REG_PAGE),
+};
+
+static const struct regmap_range ar9331_nonvolatile_regs[] = {
+	regmap_reg_range(AR9331_SW_REG_PAGE, AR9331_SW_REG_PAGE),
+};
+
+static const struct regmap_range_cfg ar9331_regmap_range[] = {
+	{
+		.selector_reg = AR9331_SW_REG_PAGE,
+		.selector_mask = GENMASK(9, 0),
+		.selector_shift = 0,
+
+		.window_start = 0,
+		.window_len = 512,
+
+		.range_min = 0,
+		.range_max = AR9331_SW_REG_PAGE - 4,
+	},
+};
+
+static const struct regmap_access_table ar9331_register_set = {
+	.yes_ranges = ar9331_valid_regs,
+	.n_yes_ranges = ARRAY_SIZE(ar9331_valid_regs),
+};
+
+static const struct regmap_access_table ar9331_volatile_set = {
+	.no_ranges = ar9331_nonvolatile_regs,
+	.n_no_ranges = ARRAY_SIZE(ar9331_nonvolatile_regs),
+};
+
+static const struct regmap_config ar9331_mdio_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = AR9331_SW_REG_PAGE,
+
+	.ranges = ar9331_regmap_range,
+	.num_ranges = ARRAY_SIZE(ar9331_regmap_range),
+
+	.volatile_table = &ar9331_volatile_set,
+	.wr_table = &ar9331_register_set,
+	.rd_table = &ar9331_register_set,
+
+	.cache_type = REGCACHE_RBTREE,
+};
+
+static struct regmap_bus ar9331_sw_bus = {
+	.reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
+	.val_format_endian_default = REGMAP_ENDIAN_NATIVE,
+	.read = ar9331_mdio_read,
+	.write = ar9331_sw_bus_write,
+	.max_raw_read = 4,
+	.max_raw_write = 4,
+};
+
+static int ar9331_sw_probe(struct mdio_device *mdiodev)
+{
+	struct ar9331_sw_priv *priv;
+	struct dsa_switch *ds;
+	int ret;
+
+	priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->regmap = devm_regmap_init(&mdiodev->dev, &ar9331_sw_bus, priv,
+					&ar9331_mdio_regmap_config);
+	if (IS_ERR(priv->regmap)) {
+		ret = PTR_ERR(priv->regmap);
+		dev_err(&mdiodev->dev, "regmap init failed: %d\n", ret);
+		return ret;
+	}
+
+	priv->sw_reset = devm_reset_control_get(&mdiodev->dev, "switch");
+	if (IS_ERR(priv->sw_reset)) {
+		dev_err(&mdiodev->dev, "missing switch reset\n");
+		return PTR_ERR(priv->sw_reset);
+	}
+
+	priv->sbus = mdiodev->bus;
+	priv->dev = &mdiodev->dev;
+
+	ret = ar9331_sw_irq_init(priv);
+	if (ret)
+		return ret;
+
+	ds = &priv->ds;
+	ds->dev = &mdiodev->dev;
+	ds->num_ports = AR9331_SW_PORTS;
+	ds->priv = priv;
+	priv->ops = ar9331_sw_ops;
+	ds->ops = &priv->ops;
+	dev_set_drvdata(&mdiodev->dev, priv);
+
+	ret = dsa_register_switch(ds);
+	if (ret)
+		goto err_remove_irq;
+
+	return 0;
+
+err_remove_irq:
+	irq_domain_remove(priv->irqdomain);
+
+	return ret;
+}
+
+static void ar9331_sw_remove(struct mdio_device *mdiodev)
+{
+	struct ar9331_sw_priv *priv = dev_get_drvdata(&mdiodev->dev);
+
+	irq_domain_remove(priv->irqdomain);
+	mdiobus_unregister(priv->mbus);
+	dsa_unregister_switch(&priv->ds);
+
+	reset_control_assert(priv->sw_reset);
+}
+
+static const struct of_device_id ar9331_sw_of_match[] = {
+	{ .compatible = "qca,ar9331-switch" },
+	{ },
+};
+
+static struct mdio_driver ar9331_sw_mdio_driver = {
+	.probe = ar9331_sw_probe,
+	.remove = ar9331_sw_remove,
+	.mdiodrv.driver = {
+		.name = AR9331_SW_NAME,
+		.of_match_table = ar9331_sw_of_match,
+	},
+};
+
+mdio_module_driver(ar9331_sw_mdio_driver);
+
+MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>");
+MODULE_DESCRIPTION("Driver for Atheros AR9331 switch");
+MODULE_LICENSE("GPL v2");
-- 
2.24.0


^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v6 1/5] net: ag71xx: port to phylink
  2019-12-17  7:23 ` [PATCH v6 1/5] net: ag71xx: port to phylink Oleksij Rempel
@ 2019-12-17 10:00   ` Russell King - ARM Linux admin
  0 siblings, 0 replies; 8+ messages in thread
From: Russell King - ARM Linux admin @ 2019-12-17 10:00 UTC (permalink / raw)
  To: Oleksij Rempel
  Cc: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Rob Herring, Vivien Didelot, Pengutronix Kernel Team,
	David S. Miller, netdev, linux-kernel, devicetree, linux-mips

On Tue, Dec 17, 2019 at 08:23:21AM +0100, Oleksij Rempel wrote:
> The port to phylink was done as close as possible to initial
> functionality.
> Theoretically this HW can support flow control, practically seems to be not
> enough to just enable it. So, more work should be done.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/ethernet/atheros/Kconfig  |   2 +-
>  drivers/net/ethernet/atheros/ag71xx.c | 147 ++++++++++++++++----------
>  2 files changed, 90 insertions(+), 59 deletions(-)
> 
> diff --git a/drivers/net/ethernet/atheros/Kconfig b/drivers/net/ethernet/atheros/Kconfig
> index 0058051ba925..2720bde5034e 100644
> --- a/drivers/net/ethernet/atheros/Kconfig
> +++ b/drivers/net/ethernet/atheros/Kconfig
> @@ -20,7 +20,7 @@ if NET_VENDOR_ATHEROS
>  config AG71XX
>  	tristate "Atheros AR7XXX/AR9XXX built-in ethernet mac support"
>  	depends on ATH79
> -	select PHYLIB
> +	select PHYLINK
>  	help
>  	  If you wish to compile a kernel for AR7XXX/91XXX and enable
>  	  ethernet support, then you should always answer Y to this.
> diff --git a/drivers/net/ethernet/atheros/ag71xx.c b/drivers/net/ethernet/atheros/ag71xx.c
> index ad8b0e3fcd2c..37a62283719e 100644
> --- a/drivers/net/ethernet/atheros/ag71xx.c
> +++ b/drivers/net/ethernet/atheros/ag71xx.c
> @@ -32,6 +32,7 @@
>  #include <linux/of_mdio.h>
>  #include <linux/of_net.h>
>  #include <linux/of_platform.h>
> +#include <linux/phylink.h>
>  #include <linux/regmap.h>
>  #include <linux/reset.h>
>  #include <linux/clk.h>
> @@ -315,6 +316,9 @@ struct ag71xx {
>  
>  	int phy_if_mode;
>  
> +	struct phylink *phylink;
> +	struct phylink_config phylink_config;
> +
>  	struct delayed_work restart_work;
>  	struct timer_list oom_timer;
>  
> @@ -845,24 +849,23 @@ static void ag71xx_hw_start(struct ag71xx *ag)
>  	netif_wake_queue(ag->ndev);
>  }
>  
> -static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
> +static void ag71xx_mac_config(struct phylink_config *config, unsigned int mode,
> +			      const struct phylink_link_state *state)
>  {
> -	struct phy_device *phydev = ag->ndev->phydev;
> +	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
>  	u32 cfg2;
>  	u32 ifctl;
>  	u32 fifo5;
>  
> -	if (!phydev->link && update) {
> -		ag71xx_hw_stop(ag);
> +	if (phylink_autoneg_inband(mode))
>  		return;
> -	}
>  
>  	if (!ag71xx_is(ag, AR7100) && !ag71xx_is(ag, AR9130))
>  		ag71xx_fast_reset(ag);
>  
>  	cfg2 = ag71xx_rr(ag, AG71XX_REG_MAC_CFG2);
>  	cfg2 &= ~(MAC_CFG2_IF_1000 | MAC_CFG2_IF_10_100 | MAC_CFG2_FDX);
> -	cfg2 |= (phydev->duplex) ? MAC_CFG2_FDX : 0;
> +	cfg2 |= (state->duplex) ? MAC_CFG2_FDX : 0;
>  
>  	ifctl = ag71xx_rr(ag, AG71XX_REG_MAC_IFCTL);
>  	ifctl &= ~(MAC_IFCTL_SPEED);
> @@ -870,7 +873,7 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
>  	fifo5 = ag71xx_rr(ag, AG71XX_REG_FIFO_CFG5);
>  	fifo5 &= ~FIFO_CFG5_BM;
>  
> -	switch (phydev->speed) {
> +	switch (state->speed) {
>  	case SPEED_1000:
>  		cfg2 |= MAC_CFG2_IF_1000;
>  		fifo5 |= FIFO_CFG5_BM;
> @@ -883,7 +886,6 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
>  		cfg2 |= MAC_CFG2_IF_10_100;
>  		break;
>  	default:
> -		WARN(1, "not supported speed %i\n", phydev->speed);
>  		return;
>  	}
>  
> @@ -897,58 +899,79 @@ static void ag71xx_link_adjust(struct ag71xx *ag, bool update)
>  	ag71xx_wr(ag, AG71XX_REG_MAC_CFG2, cfg2);
>  	ag71xx_wr(ag, AG71XX_REG_FIFO_CFG5, fifo5);
>  	ag71xx_wr(ag, AG71XX_REG_MAC_IFCTL, ifctl);
> -
> -	ag71xx_hw_start(ag);
> -
> -	if (update)
> -		phy_print_status(phydev);
>  }
>  
> -static void ag71xx_phy_link_adjust(struct net_device *ndev)
> +static void ag71xx_mac_validate(struct phylink_config *config,
> +			    unsigned long *supported,
> +			    struct phylink_link_state *state)
>  {
> -	struct ag71xx *ag = netdev_priv(ndev);
> +	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +
> +	if (state->interface != PHY_INTERFACE_MODE_NA &&
> +	    state->interface != PHY_INTERFACE_MODE_GMII &&
> +	    state->interface != PHY_INTERFACE_MODE_MII) {
> +		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> +		return;
> +	}
> +
> +	phylink_set(mask, MII);
> +
> +	/* flow control is not supported */

You should also set set the autoneg bit.

> +
> +	phylink_set(mask, 10baseT_Half);
> +	phylink_set(mask, 10baseT_Full);
> +	phylink_set(mask, 100baseT_Half);
> +	phylink_set(mask, 100baseT_Full);
>  
> -	ag71xx_link_adjust(ag, true);
> +	if (state->interface == PHY_INTERFACE_MODE_NA ||
> +	    state->interface == PHY_INTERFACE_MODE_GMII) {
> +		phylink_set(mask, 1000baseT_Full);
> +		phylink_set(mask, 1000baseX_Full);
> +	}
> +
> +	bitmap_and(supported, supported, mask,
> +		   __ETHTOOL_LINK_MODE_MASK_NBITS);
> +	bitmap_and(state->advertising, state->advertising, mask,
> +		   __ETHTOOL_LINK_MODE_MASK_NBITS);
>  }
>  
> -static int ag71xx_phy_connect(struct ag71xx *ag)
> +static void ag71xx_mac_link_down(struct phylink_config *config,
> +				 unsigned int mode, phy_interface_t interface)
>  {
> -	struct device_node *np = ag->pdev->dev.of_node;
> -	struct net_device *ndev = ag->ndev;
> -	struct device_node *phy_node;
> -	struct phy_device *phydev;
> -	int ret;
> +	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
>  
> -	if (of_phy_is_fixed_link(np)) {
> -		ret = of_phy_register_fixed_link(np);
> -		if (ret < 0) {
> -			netif_err(ag, probe, ndev, "Failed to register fixed PHY link: %d\n",
> -				  ret);
> -			return ret;
> -		}
> +	ag71xx_hw_stop(ag);
> +}
>  
> -		phy_node = of_node_get(np);
> -	} else {
> -		phy_node = of_parse_phandle(np, "phy-handle", 0);
> -	}
> +static void ag71xx_mac_link_up(struct phylink_config *config, unsigned int mode,
> +			       phy_interface_t interface,
> +			       struct phy_device *phy)
> +{
> +	struct ag71xx *ag = netdev_priv(to_net_dev(config->dev));
>  
> -	if (!phy_node) {
> -		netif_err(ag, probe, ndev, "Could not find valid phy node\n");
> -		return -ENODEV;
> -	}
> +	ag71xx_hw_start(ag);
> +}
>  
> -	phydev = of_phy_connect(ag->ndev, phy_node, ag71xx_phy_link_adjust,
> -				0, ag->phy_if_mode);
> +static const struct phylink_mac_ops ag71xx_phylink_mac_ops = {
> +	.validate = ag71xx_mac_validate,
> +	.mac_config = ag71xx_mac_config,
> +	.mac_link_down = ag71xx_mac_link_down,
> +	.mac_link_up = ag71xx_mac_link_up,

Please provide implementations for the mac_pcs_get_state and
mac_an_restart methods; these are not optional, and if phylink
decides it wants to call them, without anything here the kernel
will oops.  If you don't have anything to do for mac_pcs_get_state,
please set state->link to false.

> +};
>  
> -	of_node_put(phy_node);
> +static int ag71xx_phy_setup(struct ag71xx *ag)
> +{
> +	struct phylink *phylink;
>  
> -	if (!phydev) {
> -		netif_err(ag, probe, ndev, "Could not connect to PHY device\n");
> -		return -ENODEV;
> -	}
> +	ag->phylink_config.dev = &ag->ndev->dev;
> +	ag->phylink_config.type = PHYLINK_NETDEV;
>  
> -	phy_attached_info(phydev);
> +	phylink = phylink_create(&ag->phylink_config, ag->pdev->dev.fwnode,
> +				 ag->phy_if_mode, &ag71xx_phylink_mac_ops);
> +	if (IS_ERR(phylink))
> +		return PTR_ERR(phylink);
>  
> +	ag->phylink = phylink;
>  	return 0;
>  }
>  
> @@ -1239,6 +1262,13 @@ static int ag71xx_open(struct net_device *ndev)
>  	unsigned int max_frame_len;
>  	int ret;
>  
> +	ret = phylink_of_phy_connect(ag->phylink, ag->pdev->dev.of_node, 0);
> +	if (ret) {
> +		netif_err(ag, link, ndev, "phylink_of_phy_connect filed with err: %i\n",
> +			  ret);
> +		goto err;
> +	}
> +
>  	max_frame_len = ag71xx_max_frame_len(ndev->mtu);
>  	ag->rx_buf_size =
>  		SKB_DATA_ALIGN(max_frame_len + NET_SKB_PAD + NET_IP_ALIGN);
> @@ -1251,11 +1281,7 @@ static int ag71xx_open(struct net_device *ndev)
>  	if (ret)
>  		goto err;
>  
> -	ret = ag71xx_phy_connect(ag);
> -	if (ret)
> -		goto err;
> -
> -	phy_start(ndev->phydev);
> +	phylink_start(ag->phylink);
>  
>  	return 0;
>  
> @@ -1268,8 +1294,7 @@ static int ag71xx_stop(struct net_device *ndev)
>  {
>  	struct ag71xx *ag = netdev_priv(ndev);
>  
> -	phy_stop(ndev->phydev);
> -	phy_disconnect(ndev->phydev);
> +	phylink_stop(ag->phylink);

You connect to the phy in _open() but don't disconnect it in _stop().

>  	ag71xx_hw_disable(ag);
>  
>  	return 0;
> @@ -1396,10 +1421,9 @@ static netdev_tx_t ag71xx_hard_start_xmit(struct sk_buff *skb,
>  
>  static int ag71xx_do_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
>  {
> -	if (!ndev->phydev)
> -		return -EINVAL;
> +	struct ag71xx *ag = netdev_priv(ndev);
>  
> -	return phy_mii_ioctl(ndev->phydev, ifr, cmd);
> +	return phylink_mii_ioctl(ag->phylink, ifr, cmd);
>  }
>  
>  static void ag71xx_oom_timer_handler(struct timer_list *t)
> @@ -1422,13 +1446,14 @@ static void ag71xx_restart_work_func(struct work_struct *work)
>  {
>  	struct ag71xx *ag = container_of(work, struct ag71xx,
>  					 restart_work.work);
> -	struct net_device *ndev = ag->ndev;
>  
>  	rtnl_lock();
>  	ag71xx_hw_disable(ag);
>  	ag71xx_hw_enable(ag);
> -	if (ndev->phydev->link)
> -		ag71xx_link_adjust(ag, false);
> +
> +	phylink_stop(ag->phylink);
> +	phylink_start(ag->phylink);
> +
>  	rtnl_unlock();
>  }
>  
> @@ -1768,6 +1793,12 @@ static int ag71xx_probe(struct platform_device *pdev)
>  
>  	platform_set_drvdata(pdev, ndev);
>  
> +	err = ag71xx_phy_setup(ag);

I think this function would be better called ag71xx_phylink_setup() as
it doesn't seem to be setting up the phy at all (which happens in
_open()).

> +	if (err) {
> +		netif_err(ag, probe, ndev, "failed to setup phy (%d)\n", err);
> +		goto err_mdio_remove;
> +	}
> +
>  	err = register_netdev(ndev);
>  	if (err) {
>  		netif_err(ag, probe, ndev, "unable to register net device\n");
> -- 
> 2.24.0
> 
> 

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH v6 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation
  2019-12-17  7:23 ` [PATCH v6 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation Oleksij Rempel
@ 2019-12-18 20:09   ` Rob Herring
  0 siblings, 0 replies; 8+ messages in thread
From: Rob Herring @ 2019-12-18 20:09 UTC (permalink / raw)
  To: Oleksij Rempel
  Cc: Andrew Lunn, Chris Snook, Florian Fainelli, James Hogan,
	Jay Cliburn, Mark Rutland, Paul Burton, Ralf Baechle,
	Vivien Didelot, Oleksij Rempel, Pengutronix Kernel Team,
	David S. Miller, netdev, linux-kernel, devicetree, linux-mips,
	Russell King

On Tue, 17 Dec 2019 08:23:22 +0100, Oleksij Rempel wrote:
> Atheros AR9331 has built-in 5 port switch. The switch can be configured
> to use all 5 or 4 ports. One of built-in PHYs can be used by first built-in
> ethernet controller or to be used directly by the switch over second ethernet
> controller.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  .../devicetree/bindings/net/dsa/ar9331.txt    | 148 ++++++++++++++++++
>  1 file changed, 148 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/dsa/ar9331.txt
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, other threads:[~2019-12-18 20:09 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-17  7:23 [PATCH v6 0/5] add dsa switch support for ar9331 Oleksij Rempel
2019-12-17  7:23 ` [PATCH v6 1/5] net: ag71xx: port to phylink Oleksij Rempel
2019-12-17 10:00   ` Russell King - ARM Linux admin
2019-12-17  7:23 ` [PATCH v6 2/5] dt-bindings: net: dsa: qca,ar9331 switch documentation Oleksij Rempel
2019-12-18 20:09   ` Rob Herring
2019-12-17  7:23 ` [PATCH v6 3/5] MIPS: ath79: ar9331: add ar9331-switch node Oleksij Rempel
2019-12-17  7:23 ` [PATCH v6 4/5] net: dsa: add support for Atheros AR9331 TAG format Oleksij Rempel
2019-12-17  7:23 ` [PATCH v6 5/5] net: dsa: add support for Atheros AR9331 built-in switch Oleksij Rempel

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).