From: Ludovic Barre <ludovic.barre@st.com>
To: Ulf Hansson <ulf.hansson@linaro.org>, Rob Herring <robh+dt@kernel.org>
Cc: <srinivas.kandagatla@linaro.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-mmc@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
Ludovic Barre <ludovic.barre@st.com>
Subject: [PATCH 6/9] mmc: mmci: sdmmc: add execute tuning with delay block
Date: Fri, 10 Jan 2020 14:48:20 +0100 [thread overview]
Message-ID: <20200110134823.14882-7-ludovic.barre@st.com> (raw)
In-Reply-To: <20200110134823.14882-1-ludovic.barre@st.com>
The hardware delay block is used to align the sampling clock on
the data received by SDMMC. It is mandatory for SDMMC to
support the SDR104 mode. The delay block is used to generate
an output clock which is dephased from the input clock.
The phase of the output clock must be programmed by the execute
tuning interface.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
drivers/mmc/host/mmci_stm32_sdmmc.c | 147 ++++++++++++++++++++++++++++
1 file changed, 147 insertions(+)
diff --git a/drivers/mmc/host/mmci_stm32_sdmmc.c b/drivers/mmc/host/mmci_stm32_sdmmc.c
index df08f6662431..10059fa19f4a 100644
--- a/drivers/mmc/host/mmci_stm32_sdmmc.c
+++ b/drivers/mmc/host/mmci_stm32_sdmmc.c
@@ -3,10 +3,13 @@
* Copyright (C) STMicroelectronics 2018 - All Rights Reserved
* Author: Ludovic.barre@st.com for STMicroelectronics.
*/
+#include <linux/bitfield.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
#include <linux/mmc/host.h>
#include <linux/mmc/card.h>
+#include <linux/of_address.h>
#include <linux/reset.h>
#include <linux/scatterlist.h>
#include "mmci.h"
@@ -14,6 +17,20 @@
#define SDMMC_LLI_BUF_LEN PAGE_SIZE
#define SDMMC_IDMA_BURST BIT(MMCI_STM32_IDMABNDT_SHIFT)
+#define DLYB_CR 0x0
+#define DLYB_CR_DEN BIT(0)
+#define DLYB_CR_SEN BIT(1)
+
+#define DLYB_CFGR 0x4
+#define DLYB_CFGR_SEL_MASK GENMASK(3, 0)
+#define DLYB_CFGR_UNIT_MASK GENMASK(14, 8)
+#define DLYB_CFGR_LNG_MASK GENMASK(27, 16)
+#define DLYB_CFGR_LNGF BIT(31)
+
+#define DLYB_NB_DELAY 11
+#define DLYB_CFGR_SEL_MAX (DLYB_NB_DELAY + 1)
+#define DLYB_CFGR_UNIT_MAX 127
+
struct sdmmc_lli_desc {
u32 idmalar;
u32 idmabase;
@@ -25,6 +42,12 @@ struct sdmmc_idma {
void *sg_cpu;
};
+struct sdmmc_dlyb {
+ void __iomem *base;
+ u32 unit;
+ u32 max;
+};
+
static int sdmmc_idma_validate_data(struct mmci_host *host,
struct mmc_data *data)
{
@@ -226,12 +249,24 @@ static void mmci_sdmmc_set_clkreg(struct mmci_host *host, unsigned int desired)
mmci_write_clkreg(host, clk);
}
+static void sdmmc_dlyb_input_ck(struct sdmmc_dlyb *dlyb)
+{
+ if (!dlyb || !dlyb->base)
+ return;
+
+ /* Output clock = Input clock */
+ writel_relaxed(0, dlyb->base + DLYB_CR);
+}
+
static void mmci_sdmmc_set_pwrreg(struct mmci_host *host, unsigned int pwr)
{
struct mmc_ios ios = host->mmc->ios;
+ struct sdmmc_dlyb *dlyb = host->variant_priv;
pwr = host->pwr_reg_add;
+ sdmmc_dlyb_input_ck(dlyb);
+
if (ios.power_mode == MMC_POWER_OFF) {
/* Only a reset could power-off sdmmc */
reset_control_assert(host->rst);
@@ -323,6 +358,102 @@ static bool sdmmc_busy_complete(struct mmci_host *host, u32 status, u32 err_msk)
return true;
}
+static void sdmmc_dlyb_set_cfgr(struct sdmmc_dlyb *dlyb,
+ int unit, int phase, bool sampler)
+{
+ u32 cfgr;
+
+ writel_relaxed(DLYB_CR_SEN | DLYB_CR_DEN, dlyb->base + DLYB_CR);
+
+ cfgr = FIELD_PREP(DLYB_CFGR_UNIT_MASK, unit) |
+ FIELD_PREP(DLYB_CFGR_SEL_MASK, phase);
+ writel_relaxed(cfgr, dlyb->base + DLYB_CFGR);
+
+ if (!sampler)
+ writel_relaxed(DLYB_CR_DEN, dlyb->base + DLYB_CR);
+}
+
+static int sdmmc_dlyb_lng_tuning(struct mmci_host *host)
+{
+ struct sdmmc_dlyb *dlyb = host->variant_priv;
+ u32 cfgr;
+ int i, lng, ret;
+
+ for (i = 0; i <= DLYB_CFGR_UNIT_MAX; i++) {
+ sdmmc_dlyb_set_cfgr(dlyb, i, DLYB_CFGR_SEL_MAX, true);
+
+ ret = readl_relaxed_poll_timeout(dlyb->base + DLYB_CFGR, cfgr,
+ (cfgr & DLYB_CFGR_LNGF),
+ 1, 1000);
+ if (ret) {
+ dev_warn(mmc_dev(host->mmc),
+ "delay line cfg timeout unit:%d cfgr:%d\n",
+ i, cfgr);
+ continue;
+ }
+
+ lng = FIELD_GET(DLYB_CFGR_LNG_MASK, cfgr);
+ if (lng < BIT(DLYB_NB_DELAY) && lng > 0)
+ break;
+ }
+
+ if (i > DLYB_CFGR_UNIT_MAX)
+ return -EINVAL;
+
+ dlyb->unit = i;
+ dlyb->max = __fls(lng);
+
+ return 0;
+}
+
+static int sdmmc_dlyb_phase_tuning(struct mmci_host *host, u32 opcode)
+{
+ struct sdmmc_dlyb *dlyb = host->variant_priv;
+ int cur_len = 0, max_len = 0, end_of_len = 0;
+ int phase;
+
+ for (phase = 0; phase <= dlyb->max; phase++) {
+ sdmmc_dlyb_set_cfgr(dlyb, dlyb->unit, phase, false);
+
+ if (mmc_send_tuning(host->mmc, opcode, NULL)) {
+ cur_len = 0;
+ } else {
+ cur_len++;
+ if (cur_len > max_len) {
+ max_len = cur_len;
+ end_of_len = phase;
+ }
+ }
+ }
+
+ if (!max_len) {
+ dev_err(mmc_dev(host->mmc), "no tuning point found\n");
+ return -EINVAL;
+ }
+
+ phase = end_of_len - max_len / 2;
+ sdmmc_dlyb_set_cfgr(dlyb, dlyb->unit, phase, false);
+
+ dev_dbg(mmc_dev(host->mmc), "unit:%d max_dly:%d phase:%d\n",
+ dlyb->unit, dlyb->max, phase);
+
+ return 0;
+}
+
+static int sdmmc_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct mmci_host *host = mmc_priv(mmc);
+ struct sdmmc_dlyb *dlyb = host->variant_priv;
+
+ if (!dlyb || !dlyb->base)
+ return -EINVAL;
+
+ if (sdmmc_dlyb_lng_tuning(host))
+ return -EINVAL;
+
+ return sdmmc_dlyb_phase_tuning(host, opcode);
+}
+
static struct mmci_host_ops sdmmc_variant_ops = {
.validate_data = sdmmc_idma_validate_data,
.prep_data = sdmmc_idma_prep_data,
@@ -338,5 +469,21 @@ static struct mmci_host_ops sdmmc_variant_ops = {
void sdmmc_variant_init(struct mmci_host *host)
{
+ struct device_node *np = host->mmc->parent->of_node;
+ void __iomem *base_dlyb;
+ struct sdmmc_dlyb *dlyb;
+
host->ops = &sdmmc_variant_ops;
+
+ base_dlyb = devm_of_iomap(mmc_dev(host->mmc), np, 1, NULL);
+ if (IS_ERR(base_dlyb))
+ return;
+
+ dlyb = devm_kzalloc(mmc_dev(host->mmc), sizeof(*dlyb), GFP_KERNEL);
+ if (!dlyb)
+ return;
+
+ dlyb->base = base_dlyb;
+ host->variant_priv = dlyb;
+ host->mmc_ops->execute_tuning = sdmmc_execute_tuning;
}
--
2.17.1
next prev parent reply other threads:[~2020-01-10 13:49 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-10 13:48 [PATCH 0/9] mmc: mmci: sdmmc: add sdr104 support Ludovic Barre
2020-01-10 13:48 ` [PATCH 1/9] mmc: mmci: sdmmc: replace sg_dma_xxx macros Ludovic Barre
2020-01-10 13:48 ` [PATCH 2/9] mmc: mmci: sdmmc: rename sdmmc_priv struct to sdmmc_idma Ludovic Barre
2020-01-10 13:48 ` [PATCH 3/9] mmc: mmci: add a reference at mmc_host_ops in mmci struct Ludovic Barre
2020-01-24 13:09 ` Ulf Hansson
2020-01-27 10:57 ` Ludovic BARRE
2020-01-10 13:48 ` [PATCH 4/9] mmc: mmci: add private pointer for variant Ludovic Barre
2020-01-10 13:48 ` [PATCH 5/9] dt-bindings: mmc: mmci: add delay block base register for sdmmc Ludovic Barre
2020-01-15 14:56 ` Rob Herring
2020-01-16 9:20 ` Ludovic BARRE
2020-01-16 14:33 ` Rob Herring
2020-01-16 14:52 ` Ludovic BARRE
2020-01-10 13:48 ` Ludovic Barre [this message]
2020-01-24 13:10 ` [PATCH 6/9] mmc: mmci: sdmmc: add execute tuning with delay block Ulf Hansson
2020-01-27 13:19 ` Ludovic BARRE
2020-01-10 13:48 ` [PATCH 7/9] mmc: mmci: add volt_switch callbacks Ludovic Barre
2020-01-24 13:12 ` Ulf Hansson
2020-01-27 13:21 ` Ludovic BARRE
2020-01-10 13:48 ` [PATCH 8/9] mmc: mmci: sdmmc: add voltage switch functions Ludovic Barre
2020-01-24 13:16 ` Ulf Hansson
2020-01-27 13:50 ` Ludovic BARRE
2020-01-10 13:48 ` [PATCH 9/9] mmc: mmci: add sdmmc variant revision 2.0 Ludovic Barre
2020-01-24 12:55 ` [PATCH 0/9] mmc: mmci: sdmmc: add sdr104 support Ludovic BARRE
2020-01-24 13:19 ` Ulf Hansson
2020-01-27 13:52 ` Ludovic BARRE
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200110134823.14882-7-ludovic.barre@st.com \
--to=ludovic.barre@st.com \
--cc=alexandre.torgue@st.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=robh+dt@kernel.org \
--cc=srinivas.kandagatla@linaro.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).