Linux-mmc Archive on lore.kernel.org
 help / color / Atom feed
From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Cc: adrian.hunter@intel.com, ulf.hansson@linaro.org,
	robh+dt@kernel.org, linux-mmc@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	devicetree@vger.kernel.org, Asutosh Das <asutoshd@codeaurora.org>,
	Vijay Viswanath <vviswana@codeaurora.org>,
	Andy Gross <agross@kernel.org>
Subject: Re: [PATCH V2 2/3] mmc: sdhci-msm: Use internal voltage control
Date: Fri, 22 May 2020 10:04:15 -0700
Message-ID: <20200522170415.GI11847@yoga> (raw)
In-Reply-To: <08d11687-7aee-2c62-9435-670be1afb21e@codeaurora.org>

On Fri 22 May 06:27 PDT 2020, Veerabhadrarao Badiganti wrote:

> Hi Bjorn,
> 
> On 5/22/2020 12:37 AM, Bjorn Andersson wrote:
> > On Thu 21 May 08:23 PDT 2020, Veerabhadrarao Badiganti wrote:
> > 
> > > On qcom SD host controllers voltage switching be done after the HW
> > > is ready for it. The HW informs its readiness through power irq.
> > > The voltage switching should happen only then.
> > > 
> > > Use the internal voltage switching and then control the voltage
> > > switching using power irq.
> > > 
> > > Set the regulator load as well so that regulator can be configured
> > > in LPM mode when in is not being used.
> > > 
> > > Co-developed-by: Asutosh Das <asutoshd@codeaurora.org>
> > > Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
> > > Co-developed-by: Vijay Viswanath <vviswana@codeaurora.org>
> > > Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
> > > Co-developed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
> > > Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
> > Looks better, thanks.
> > 
> > > ---
> > >   drivers/mmc/host/sdhci-msm.c | 207 +++++++++++++++++++++++++++++++++++++++++--
> > >   1 file changed, 198 insertions(+), 9 deletions(-)
> > > 
> > > diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
> > [..]
> > >   static const struct sdhci_msm_offset *sdhci_priv_msm_offset(struct sdhci_host *host)
> > > @@ -1298,6 +1302,71 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
> > >   		sdhci_msm_hs400(host, &mmc->ios);
> > >   }
> > > +static int sdhci_msm_set_vmmc(struct mmc_host *mmc)
> > > +{
> > > +	int ret;
> > > +
> > > +	if (IS_ERR(mmc->supply.vmmc))
> > > +		return 0;
> > > +
> > > +	ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd);
> > > +	if (ret)
> > > +		dev_err(mmc_dev(mmc), "%s: vmmc set ocr with vdd=%d failed: %d\n",
> > > +			mmc_hostname(mmc), mmc->ios.vdd, ret);
> > Missed this one on v1, in the event that mmc_regulator_set_ocr() return
> > a non-zero value it has already printed an error message. So please
> > replace the tail with just:
> > 
> > 	return mmc_regulator_set_ocr(...);
> > 
> > > +
> > > +	return ret;
> > > +}
> > > +
> > > +static int sdhci_msm_set_vqmmc(struct sdhci_msm_host *msm_host,
> > > +			      struct mmc_host *mmc, bool level)
> > > +{
> > > +	int load, ret;
> > > +	struct mmc_ios ios;
> > > +
> > > +	if (IS_ERR(mmc->supply.vqmmc)			 ||
> > > +	    (mmc->ios.power_mode == MMC_POWER_UNDEFINED) ||
> > > +	    (msm_host->vqmmc_enabled == level))
> > > +		return 0;
> > > +
> > > +	if (msm_host->vqmmc_load) {
> > > +		load = level ? msm_host->vqmmc_load : 0;
> > > +		ret = regulator_set_load(mmc->supply.vqmmc, load);
> > Sorry for the late reply on v1, but please see my explanation regarding
> > load and always-on regulators there.
> 
> <Merging your comment from V1 here>
> 
> >> You should still call regulator_enable()/regulator_disable() on your
> >> consumer regulator in this driver. When you do this the regulator core
> >> will conclude that the regulator_dev (i.e. the part that represents the
> >> hardware) is marked always_on and will not enable/disable the regulator.
> 
> >> But it will still invoke _regulator_handle_consumer_enable() and
> >> _regulator_handle_consumer_disable(), which will aggregate the "load" of
> >> all client regulators and update the regulator's load.
> 
> >> So this will apply the load as you expect regardless of it being
> >> supplied by a regulator marked as always_on.
> 
> Since I'm not turning off this regulator for eMMC, I wanted to keep it in
> LPM mode
> to save some power.
> When the regulator configured in auto mode (RPMH_REGULATOR_MODE_AUTO) it
> switches to LPM/HPM mode based on the active load.
> So i have to minimize my driver load requirement so that I can let this
> regulator
> in LPM mode.
> So i need to set load every-time I disable/enable the regulator.
> 

You call regulator_enable(vqmmc) and regulator_disable() below, so you
are telling the regulator framework that your struct regulator should be
"on" or "off".

This will cause the sum of all struct regulator's for the underlying
struct regulator_dev to be recalculated. So after calling
regulator_disable() below your effective addition to the load
calculation is 0, regardless of which load you have specified.

Independent of this the property regulator-always-on (always_on in
struct regulator_dev) will determine if the enable/disable request will
actually be sent to the RPMh.


So, if you where to not call regulator_disable() for eMMC your argument
is correct, but as far as I can see you are and you're relying on the
regulator core to keep it always-on - and then the load logic is in
effect still.

Regards,
Bjorn

> > > +		if (ret) {
> > > +			dev_err(mmc_dev(mmc), "%s: vqmmc set load failed: %d\n",
> > > +				mmc_hostname(mmc), ret);
> > > +			goto out;
> > > +		}
> > > +	}
> > > +
> > > +	if (level) {
> > > +		/* Set the IO voltage regulator to default voltage level */
> > > +		if (msm_host->caps_0 & CORE_3_0V_SUPPORT)
> > > +			ios.signal_voltage = MMC_SIGNAL_VOLTAGE_330;
> > > +		else if (msm_host->caps_0 & CORE_1_8V_SUPPORT)
> > > +			ios.signal_voltage = MMC_SIGNAL_VOLTAGE_180;
> > > +
> > > +		if (msm_host->caps_0 & CORE_VOLT_SUPPORT) {
> > > +			ret = mmc_regulator_set_vqmmc(mmc, &ios);
> > > +			if (ret < 0) {
> > > +				dev_err(mmc_dev(mmc), "%s: vqmmc set volgate failed: %d\n",
> > > +					mmc_hostname(mmc), ret);
> > > +				goto out;
> > > +			}
> > > +		}
> > > +		ret = regulator_enable(mmc->supply.vqmmc);
> > > +	} else {
> > > +		ret = regulator_disable(mmc->supply.vqmmc);
> > > +	}
> > > +
> > > +	if (ret)
> > > +		dev_err(mmc_dev(mmc), "%s: vqmm %sable failed: %d\n",
> > > +			mmc_hostname(mmc), level ? "en":"dis", ret);
> > > +	else
> > > +		msm_host->vqmmc_enabled = level;
> > > +out:
> > > +	return ret;
> > > +}

  reply index

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-05-15 11:18 [PATCH V1 0/3] Internal voltage control for qcom SDHC Veerabhadrarao Badiganti
2020-05-15 11:18 ` [PATCH V1 1/3] dt-bindings: mmc: Supply max load for mmc supplies Veerabhadrarao Badiganti
2020-05-15 11:18 ` [PATCH V1 2/3] mmc: sdhci-msm: Use internal voltage control Veerabhadrarao Badiganti
2020-05-18 19:57   ` Bjorn Andersson
2020-05-19  3:11     ` Bjorn Andersson
2020-05-20 11:16     ` Veerabhadrarao Badiganti
2020-05-21 18:21       ` Bjorn Andersson
2020-05-15 11:18 ` [PATCH V1 3/3] mmc: sdhci: Allow platform controlled voltage switching Veerabhadrarao Badiganti
2020-05-19  6:06   ` Adrian Hunter
2020-05-20 11:19     ` Veerabhadrarao Badiganti
2020-05-21 15:23 ` [PATCH V2 0/3] Internal voltage control for qcom SDHC Veerabhadrarao Badiganti
2020-05-21 15:23   ` [PATCH V2 1/3] dt-bindings: mmc: Supply max load for mmc supplies Veerabhadrarao Badiganti
2020-05-21 15:23   ` [PATCH V2 2/3] mmc: sdhci-msm: Use internal voltage control Veerabhadrarao Badiganti
2020-05-21 19:07     ` Bjorn Andersson
2020-05-22 13:27       ` Veerabhadrarao Badiganti
2020-05-22 17:04         ` Bjorn Andersson [this message]
2020-05-21 15:23   ` [PATCH V2 3/3] mmc: sdhci: Allow platform controlled voltage switching Veerabhadrarao Badiganti
2020-05-25  5:42     ` Adrian Hunter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200522170415.GI11847@yoga \
    --to=bjorn.andersson@linaro.org \
    --cc=adrian.hunter@intel.com \
    --cc=agross@kernel.org \
    --cc=asutoshd@codeaurora.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=ulf.hansson@linaro.org \
    --cc=vbadigan@codeaurora.org \
    --cc=vviswana@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-mmc Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-mmc/0 linux-mmc/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-mmc linux-mmc/ https://lore.kernel.org/linux-mmc \
		linux-mmc@vger.kernel.org
	public-inbox-index linux-mmc

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-mmc


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git