arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

[Markus Reichl]

Working with rootfs on two 128GB mmcs on rk3399-roc-pc.

One (mmc name 128G72, one screw hole) works fine in HS400 mode.
Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
mmc1: "running CQE recovery", even hangs with damaged fs,
when running under heavy load, e.g. compiling kernel.
Both run fine with HS200.

Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
[0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3

Therefore I propose to disable HS400 mode on roc-pc for now.

Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
---
 arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
index 29a50a083c42..33df95e384b4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
@@ -660,8 +660,6 @@
 
 &sdhci {
 	bus-width = <8>;
-	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
 	non-removable;
 	status = "okay";
 };
-- 
2.20.1

Re: arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

[Heiko Stuebner]

Hi Markus,

$subject is missing the [PATCH] prefix

Am Montag, 11. November 2019, 10:51:04 CET schrieb Markus Reichl:
> Working with rootfs on two 128GB mmcs on rk3399-roc-pc.
> 
> One (mmc name 128G72, one screw hole) works fine in HS400 mode.
> Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
> mmc1: "running CQE recovery", even hangs with damaged fs,
> when running under heavy load, e.g. compiling kernel.
> Both run fine with HS200.
> 
> Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
> [0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3

I'm hoping for some input from other people in Cc but your mail headers
also referenced the drive-impendance series from Christoph [0], which
it seems we need to poke the phy maintainer again.

Did you check if changing the impedance helped (like the signal dampening
Philipp described in one of the replies there).

[0] https://patchwork.kernel.org/patch/10835567/
most current v2 it seems is https://patchwork.kernel.org/patch/10842421/

> Therefore I propose to disable HS400 mode on roc-pc for now.

Hoping for more input :-)


Heiko


> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
> ---
>  arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi | 2 --
>  1 file changed, 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> index 29a50a083c42..33df95e384b4 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> @@ -660,8 +660,6 @@
>  
>  &sdhci {
>  	bus-width = <8>;
> -	mmc-hs400-1_8v;
> -	mmc-hs400-enhanced-strobe;
>  	non-removable;
>  	status = "okay";
>  };
> 

Re: arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

[Markus Reichl]

Hi Heiko,

Am 14.11.19 um 14:10 schrieb Heiko Stuebner:
> Hi Markus,
> 
> $subject is missing the [PATCH] prefix
will fix.
> 
> Am Montag, 11. November 2019, 10:51:04 CET schrieb Markus Reichl:
>> Working with rootfs on two 128GB mmcs on rk3399-roc-pc.
>> 
>> One (mmc name 128G72, one screw hole) works fine in HS400 mode.
>> Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
>> mmc1: "running CQE recovery", even hangs with damaged fs,
>> when running under heavy load, e.g. compiling kernel.
>> Both run fine with HS200.
>> 
>> Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
>> [0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3
> 
> I'm hoping for some input from other people in Cc but your mail headers
> also referenced the drive-impendance series from Christoph [0], which
> it seems we need to poke the phy maintainer again.
> 
> Did you check if changing the impedance helped (like the signal dampening
> Philipp described in one of the replies there).

checked with

&emmc_phy {
+       drive-impedance-ohm = <33>;

gives no improvement:
[    1.688590] mmc1: CQHCI version 5.10
[    1.714157] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    1.797822] mmc1: Command Queue Engine enabled
[    1.798259] mmc1: new HS400 Enhanced strobe MMC card at address 0001
[    1.800034] mmcblk1: mmc1:0001 DJNB4R 116 GiB 
[    1.800643] mmcblk1boot0: mmc1:0001 DJNB4R partition 1 4.00 MiB
[    1.801408] mmcblk1boot1: mmc1:0001 DJNB4R partition 2 4.00 MiB
[    1.802886] mmcblk1rpmb: mmc1:0001 DJNB4R partition 3 4.00 MiB, chardev (246:0)
...
[  100.118020] mmc1: running CQE recovery
[  100.120890] ------------[ cut here ]------------
[  100.121310] mmc1: cqhci: spurious TCN for tag 2
[  100.121802] WARNING: CPU: 0 PID: 232 at drivers/mmc/host/cqhci.c:729 cqhci_irq+0x30c/0x480
[  100.122530] Modules linked in: rfkill snd_soc_hdmi_codec dw_hdmi_i2s_audio dw_hdmi_cec rockchipdrm crct10dif_ce analogix_dp dw_mipi_dsi snd_soc_simple_card dw_hdmi cec snd_soc_rockchip_i2s snd_soc_simple_card_utils panfrost snd_soc_rockchip_pcm drm_kms_helper snd_soc_core gpu_sched snd_pcm_dmaengine syscopyarea sysfillrect sysimgblt snd_pcm fb_sys_fops snd_timer snd drm soundcore fusb302 tcpm typec rockchip_saradc drm_panel_orientation_quirks ipv6
[  100.126097] CPU: 0 PID: 232 Comm: kworker/0:2H Not tainted 5.4.0-rc7-next-20191112-00007-g2ad177c77749 #44
[  100.126946] Hardware name: Firefly ROC-RK3399-PC Board (DT)
[  100.127454] Workqueue: kblockd blk_mq_run_work_fn
[  100.127885] pstate: 20000085 (nzCv daIf -PAN -UAO)
[  100.128318] pc : cqhci_irq+0x30c/0x480
[  100.128660] lr : cqhci_irq+0x30c/0x480
[  100.128997] sp : ffff800010003d10
[  100.129298] x29: ffff800010003d10 x28: 0000000000000000 
[  100.129777] x27: 0000000000000001 x26: ffff8000108e0fe8 
[  100.130257] x25: ffff0000f5ae5c98 x24: ffff800010b7e1a8 
[  100.130737] x23: ffff800010b198c8 x22: ffff0000f5a80000 
[  100.131216] x21: 0000000000000002 x20: 0000000000000002 
[  100.131694] x19: ffff0000f5ae5c80 x18: 0000000000000010 
[  100.132173] x17: 0000000000000000 x16: 0000000000000000 
[  100.132653] x15: ffffffffffffffff x14: ffff800010b198c8 
[  100.133132] x13: ffff800090003a77 x12: ffff800010003a7f 
[  100.133612] x11: ffff800010b30000 x10: ffff800010003a00 
[  100.134092] x9 : 00000000ffffffd0 x8 : ffff80001045a060 
[  100.134571] x7 : 000000000000025f x6 : ffff800010b979e2 
[  100.135050] x5 : 0000000000000001 x4 : 0000000000000000 
[  100.135529] x3 : 0000000000000000 x2 : 0000000000000000 
[  100.136007] x1 : e005989da46f2500 x0 : 0000000000000000 
[  100.136486] Call trace:
[  100.136719]  cqhci_irq+0x30c/0x480
[  100.137033]  sdhci_arasan_cqhci_irq+0x58/0x80
[  100.137430]  sdhci_irq+0xb8/0xbb8
[  100.137742]  __handle_irq_event_percpu+0x6c/0x170
[  100.138169]  handle_irq_event_percpu+0x34/0x88
[  100.138575]  handle_irq_event+0x44/0xc8
[  100.138927]  handle_fasteoi_irq+0xb4/0x160
[  100.139302]  generic_handle_irq+0x24/0x38
[  100.139670]  __handle_domain_irq+0x60/0xb8
[  100.140045]  gic_handle_irq+0xc0/0x158
[  100.140389]  el1_irq+0xb8/0x180
[  100.140684]  _raw_spin_unlock_irqrestore+0x20/0x48
[  100.141119]  sdhci_cqe_enable+0xec/0x108
[  100.141478]  sdhci_arasan_cqe_enable+0x4c/0x58
[  100.141880]  cqhci_request+0x2d0/0x500
[  100.142226]  mmc_cqe_start_req+0x50/0x60
[  100.142585]  mmc_blk_mq_issue_rq+0x430/0x794
[  100.142974]  mmc_mq_queue_rq+0x104/0x270
[  100.143332]  blk_mq_dispatch_rq_list+0xa8/0x580
[  100.143746]  blk_mq_sched_dispatch_requests+0xf4/0x1d8
[  100.144210]  __blk_mq_run_hw_queue+0xac/0x120
[  100.144605]  blk_mq_run_work_fn+0x1c/0x28
[  100.144974]  process_one_work+0x1e0/0x358
[  100.145340]  worker_thread+0x40/0x488
[  100.145679]  kthread+0x118/0x120
[  100.145977]  ret_from_fork+0x10/0x18
[  100.146302] ---[ end trace 6277099ad751ed64 ]---
[  100.213815] mmc1: running CQE recovery
[  100.413933] mmc1: running CQE recovery

> 
> [0] https://patchwork.kernel.org/patch/10835567/
> most current v2 it seems is https://patchwork.kernel.org/patch/10842421/
> 
>> Therefore I propose to disable HS400 mode on roc-pc for now.
> 
> Hoping for more input :-)

Hoping, too.


Gruß,
-- 
Markus Reichl
> 
> 
> Heiko
> 
> 
>> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
>> ---
>>  arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi | 2 --
>>  1 file changed, 2 deletions(-)
>> 
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
>> index 29a50a083c42..33df95e384b4 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
>> @@ -660,8 +660,6 @@
>>  
>>  &sdhci {
>>  	bus-width = <8>;
>> -	mmc-hs400-1_8v;
>> -	mmc-hs400-enhanced-strobe;
>>  	non-removable;
>>  	status = "okay";
>>  };
>> 
> 

Re: arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

[Heiko Stübner]

Hi Markus,

Am Freitag, 15. November 2019, 11:37:58 CET schrieb Markus Reichl:
> Am 14.11.19 um 14:10 schrieb Heiko Stuebner:
> > $subject is missing the [PATCH] prefix
> will fix.

no need to resend just for this ... just to keep in mind for future patches ;-)


> > Am Montag, 11. November 2019, 10:51:04 CET schrieb Markus Reichl:
> >> Working with rootfs on two 128GB mmcs on rk3399-roc-pc.
> >> 
> >> One (mmc name 128G72, one screw hole) works fine in HS400 mode.
> >> Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
> >> mmc1: "running CQE recovery", even hangs with damaged fs,
> >> when running under heavy load, e.g. compiling kernel.
> >> Both run fine with HS200.
> >> 
> >> Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
> >> [0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3
> > 
> > I'm hoping for some input from other people in Cc but your mail headers
> > also referenced the drive-impendance series from Christoph [0], which
> > it seems we need to poke the phy maintainer again.
> > 
> > Did you check if changing the impedance helped (like the signal dampening
> > Philipp described in one of the replies there).
> 
> checked with
> 
> &emmc_phy {
> +       drive-impedance-ohm = <33>;
> 
> gives no improvement:

That is sad ... I guess we really should disable hs400 then ...
that may give others more incentive to dive deeper ;-)


Heiko


> [    1.688590] mmc1: CQHCI version 5.10
> [    1.714157] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
> [    1.797822] mmc1: Command Queue Engine enabled
> [    1.798259] mmc1: new HS400 Enhanced strobe MMC card at address 0001
> [    1.800034] mmcblk1: mmc1:0001 DJNB4R 116 GiB 
> [    1.800643] mmcblk1boot0: mmc1:0001 DJNB4R partition 1 4.00 MiB
> [    1.801408] mmcblk1boot1: mmc1:0001 DJNB4R partition 2 4.00 MiB
> [    1.802886] mmcblk1rpmb: mmc1:0001 DJNB4R partition 3 4.00 MiB, chardev (246:0)
> ...
> [  100.118020] mmc1: running CQE recovery
> [  100.120890] ------------[ cut here ]------------
> [  100.121310] mmc1: cqhci: spurious TCN for tag 2
> [  100.121802] WARNING: CPU: 0 PID: 232 at drivers/mmc/host/cqhci.c:729 cqhci_irq+0x30c/0x480
> [  100.122530] Modules linked in: rfkill snd_soc_hdmi_codec dw_hdmi_i2s_audio dw_hdmi_cec rockchipdrm crct10dif_ce analogix_dp dw_mipi_dsi snd_soc_simple_card dw_hdmi cec snd_soc_rockchip_i2s snd_soc_simple_card_utils panfrost snd_soc_rockchip_pcm drm_kms_helper snd_soc_core gpu_sched snd_pcm_dmaengine syscopyarea sysfillrect sysimgblt snd_pcm fb_sys_fops snd_timer snd drm soundcore fusb302 tcpm typec rockchip_saradc drm_panel_orientation_quirks ipv6
> [  100.126097] CPU: 0 PID: 232 Comm: kworker/0:2H Not tainted 5.4.0-rc7-next-20191112-00007-g2ad177c77749 #44
> [  100.126946] Hardware name: Firefly ROC-RK3399-PC Board (DT)
> [  100.127454] Workqueue: kblockd blk_mq_run_work_fn
> [  100.127885] pstate: 20000085 (nzCv daIf -PAN -UAO)
> [  100.128318] pc : cqhci_irq+0x30c/0x480
> [  100.128660] lr : cqhci_irq+0x30c/0x480
> [  100.128997] sp : ffff800010003d10
> [  100.129298] x29: ffff800010003d10 x28: 0000000000000000 
> [  100.129777] x27: 0000000000000001 x26: ffff8000108e0fe8 
> [  100.130257] x25: ffff0000f5ae5c98 x24: ffff800010b7e1a8 
> [  100.130737] x23: ffff800010b198c8 x22: ffff0000f5a80000 
> [  100.131216] x21: 0000000000000002 x20: 0000000000000002 
> [  100.131694] x19: ffff0000f5ae5c80 x18: 0000000000000010 
> [  100.132173] x17: 0000000000000000 x16: 0000000000000000 
> [  100.132653] x15: ffffffffffffffff x14: ffff800010b198c8 
> [  100.133132] x13: ffff800090003a77 x12: ffff800010003a7f 
> [  100.133612] x11: ffff800010b30000 x10: ffff800010003a00 
> [  100.134092] x9 : 00000000ffffffd0 x8 : ffff80001045a060 
> [  100.134571] x7 : 000000000000025f x6 : ffff800010b979e2 
> [  100.135050] x5 : 0000000000000001 x4 : 0000000000000000 
> [  100.135529] x3 : 0000000000000000 x2 : 0000000000000000 
> [  100.136007] x1 : e005989da46f2500 x0 : 0000000000000000 
> [  100.136486] Call trace:
> [  100.136719]  cqhci_irq+0x30c/0x480
> [  100.137033]  sdhci_arasan_cqhci_irq+0x58/0x80
> [  100.137430]  sdhci_irq+0xb8/0xbb8
> [  100.137742]  __handle_irq_event_percpu+0x6c/0x170
> [  100.138169]  handle_irq_event_percpu+0x34/0x88
> [  100.138575]  handle_irq_event+0x44/0xc8
> [  100.138927]  handle_fasteoi_irq+0xb4/0x160
> [  100.139302]  generic_handle_irq+0x24/0x38
> [  100.139670]  __handle_domain_irq+0x60/0xb8
> [  100.140045]  gic_handle_irq+0xc0/0x158
> [  100.140389]  el1_irq+0xb8/0x180
> [  100.140684]  _raw_spin_unlock_irqrestore+0x20/0x48
> [  100.141119]  sdhci_cqe_enable+0xec/0x108
> [  100.141478]  sdhci_arasan_cqe_enable+0x4c/0x58
> [  100.141880]  cqhci_request+0x2d0/0x500
> [  100.142226]  mmc_cqe_start_req+0x50/0x60
> [  100.142585]  mmc_blk_mq_issue_rq+0x430/0x794
> [  100.142974]  mmc_mq_queue_rq+0x104/0x270
> [  100.143332]  blk_mq_dispatch_rq_list+0xa8/0x580
> [  100.143746]  blk_mq_sched_dispatch_requests+0xf4/0x1d8
> [  100.144210]  __blk_mq_run_hw_queue+0xac/0x120
> [  100.144605]  blk_mq_run_work_fn+0x1c/0x28
> [  100.144974]  process_one_work+0x1e0/0x358
> [  100.145340]  worker_thread+0x40/0x488
> [  100.145679]  kthread+0x118/0x120
> [  100.145977]  ret_from_fork+0x10/0x18
> [  100.146302] ---[ end trace 6277099ad751ed64 ]---
> [  100.213815] mmc1: running CQE recovery
> [  100.413933] mmc1: running CQE recovery
> 
> > 
> > [0] https://patchwork.kernel.org/patch/10835567/
> > most current v2 it seems is https://patchwork.kernel.org/patch/10842421/
> > 
> >> Therefore I propose to disable HS400 mode on roc-pc for now.
> > 
> > Hoping for more input :-)
> 
> Hoping, too.
> 
> 
> Gruß,
> > 
> > 
> > Heiko
> > 
> > 
> >> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
> >> ---
> >>  arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi | 2 --
> >>  1 file changed, 2 deletions(-)
> >> 
> >> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> >> index 29a50a083c42..33df95e384b4 100644
> >> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> >> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> >> @@ -660,8 +660,6 @@
> >>  
> >>  &sdhci {
> >>  	bus-width = <8>;
> >> -	mmc-hs400-1_8v;
> >> -	mmc-hs400-enhanced-strobe;
> >>  	non-removable;
> >>  	status = "okay";
> >>  };
> >> 
> > 
> 
> 

Re: arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

[Doug Anderson]

Hi,


On Fri, Nov 15, 2019 at 3:19 AM Heiko Stübner <heiko@sntech.de> wrote:
>
> Hi Markus,
>
> Am Freitag, 15. November 2019, 11:37:58 CET schrieb Markus Reichl:
> > Am 14.11.19 um 14:10 schrieb Heiko Stuebner:
> > > $subject is missing the [PATCH] prefix
> > will fix.
>
> no need to resend just for this ... just to keep in mind for future patches ;-)
>
>
> > > Am Montag, 11. November 2019, 10:51:04 CET schrieb Markus Reichl:
> > >> Working with rootfs on two 128GB mmcs on rk3399-roc-pc.
> > >>
> > >> One (mmc name 128G72, one screw hole) works fine in HS400 mode.
> > >> Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
> > >> mmc1: "running CQE recovery", even hangs with damaged fs,
> > >> when running under heavy load, e.g. compiling kernel.
> > >> Both run fine with HS200.
> > >>
> > >> Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
> > >> [0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3
> > >
> > > I'm hoping for some input from other people in Cc but your mail headers
> > > also referenced the drive-impendance series from Christoph [0], which
> > > it seems we need to poke the phy maintainer again.
> > >
> > > Did you check if changing the impedance helped (like the signal dampening
> > > Philipp described in one of the replies there).
> >
> > checked with
> >
> > &emmc_phy {
> > +       drive-impedance-ohm = <33>;
> >
> > gives no improvement:
>
> That is sad ... I guess we really should disable hs400 then ...
> that may give others more incentive to dive deeper ;-)

Just out of curiosity, is the problem with the strobe line, or with
hs400?  Have you tried using the solution from "rk3399-gru.dtsi"?
Namely:

        /*
         * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
         * same (or nearly the same) performance for all eMMC that are intended
         * to be used.
         */
        assigned-clock-rates = <150000000>;

IIRC hs400 on rk3399 was a bit iffy but running at 150 MHz made it
much more reliable and still gave you 300 MB/s transfer rate (so much
better than hs200).  In reality many eMMC chips can't do > 300 MB/s
anyway.

-Doug

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

[Markus Reichl]

Hi Doug,

Am 18.11.19 um 17:08 schrieb Doug Anderson:
> Hi,
> 
> 
> On Fri, Nov 15, 2019 at 3:19 AM Heiko Stübner <heiko@sntech.de> wrote:
>>
>> Hi Markus,
>>
>> Am Freitag, 15. November 2019, 11:37:58 CET schrieb Markus Reichl:
>> > Am 14.11.19 um 14:10 schrieb Heiko Stuebner:
>> > > $subject is missing the [PATCH] prefix
>> > will fix.
>>
>> no need to resend just for this ... just to keep in mind for future patches ;-)
>>
>>
>> > > Am Montag, 11. November 2019, 10:51:04 CET schrieb Markus Reichl:
>> > >> Working with rootfs on two 128GB mmcs on rk3399-roc-pc.
>> > >>
>> > >> One (mmc name 128G72, one screw hole) works fine in HS400 mode.
>> > >> Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
>> > >> mmc1: "running CQE recovery", even hangs with damaged fs,
>> > >> when running under heavy load, e.g. compiling kernel.
>> > >> Both run fine with HS200.
>> > >>
>> > >> Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
>> > >> [0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3
>> > >
>> > > I'm hoping for some input from other people in Cc but your mail headers
>> > > also referenced the drive-impendance series from Christoph [0], which
>> > > it seems we need to poke the phy maintainer again.
>> > >
>> > > Did you check if changing the impedance helped (like the signal dampening
>> > > Philipp described in one of the replies there).
>> >
>> > checked with
>> >
>> > &emmc_phy {
>> > +       drive-impedance-ohm = <33>;
>> >
>> > gives no improvement:
>>
>> That is sad ... I guess we really should disable hs400 then ...
>> that may give others more incentive to dive deeper ;-)
> 
> Just out of curiosity, is the problem with the strobe line, or with
> hs400?  Have you tried using the solution from "rk3399-gru.dtsi"?
> Namely:
> 
>         /*
>          * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
>          * same (or nearly the same) performance for all eMMC that are intended
>          * to be used.
>          */
>         assigned-clock-rates = <150000000>;
> 
> IIRC hs400 on rk3399 was a bit iffy but running at 150 MHz made it
> much more reliable and still gave you 300 MB/s transfer rate (so much
> better than hs200).  In reality many eMMC chips can't do > 300 MB/s
> anyway.
> 
I tried 150000000 and 100000000, but it did not help.

Gruß,
--
Markus

> -Doug
> 

Re: arm64: dts: rockchip: Disable HS400 for mmc on rk3399-roc-pc

[Heiko Stuebner]

Am Montag, 11. November 2019, 10:51:04 CET schrieb Markus Reichl:
> Working with rootfs on two 128GB mmcs on rk3399-roc-pc.
> 
> One (mmc name 128G72, one screw hole) works fine in HS400 mode.
> Other (mmc name DJNB4R, firefly on pcb, two screw holes) gets lots of
> mmc1: "running CQE recovery", even hangs with damaged fs,
> when running under heavy load, e.g. compiling kernel.
> Both run fine with HS200.
> 
> Disabling CQ with patch mmc: core: Add MMC Command Queue Support kernel parameter [0] did not help.
> [0] https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commit/54e264154b87dfe32a8359b2726e2d5611adbaf3
> 
> Therefore I propose to disable HS400 mode on roc-pc for now.
> 
> Signed-off-by: Markus Reichl <m.reichl-SRyzfwRm/0rPTwkrwQOX7A@public.gmane.org>

applied for 5.6 (or maybe still 5.5)

Thanks
Heiko