linux-mmc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Adrian Hunter <adrian.hunter@intel.com>
To: Lars Povlsen <lars.povlsen@microchip.com>,
	Ulf Hansson <ulf.hansson@linaro.org>, SoC Team <soc@kernel.org>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>,
	linux-mmc@vger.kernel.org, devicetree@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org,
	Alexandre Belloni <alexandre.belloni@bootlin.com>
Subject: Re: [PATCH v4 2/3] sdhci: sparx5: Add Sparx5 SoC eMMC driver
Date: Thu, 18 Jun 2020 17:43:27 +0300	[thread overview]
Message-ID: <aee90bbf-f0ff-b0cb-b10a-9a2f3bb6acca@intel.com> (raw)
In-Reply-To: <20200618141326.25723-3-lars.povlsen@microchip.com>

On 18/06/20 5:13 pm, Lars Povlsen wrote:
> This adds the eMMC driver for the Sparx5 SoC. It is based upon the
> designware IP, but requires some extra initialization and quirks.
> 
> Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>

Acked-by: Adrian Hunter <adrian.hunter@intel.com>

> ---
>  drivers/mmc/host/Kconfig           |  13 ++
>  drivers/mmc/host/Makefile          |   1 +
>  drivers/mmc/host/sdhci-of-sparx5.c | 269 +++++++++++++++++++++++++++++
>  3 files changed, 283 insertions(+)
>  create mode 100644 drivers/mmc/host/sdhci-of-sparx5.c
> 
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 3b706af35ec31..a3bad4b4ed7ea 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -213,6 +213,19 @@ config MMC_SDHCI_OF_DWCMSHC
>  	  If you have a controller with this interface, say Y or M here.
>  	  If unsure, say N.
>  
> +config MMC_SDHCI_OF_SPARX5
> +	tristate "SDHCI OF support for the MCHP Sparx5 SoC"
> +	depends on MMC_SDHCI_PLTFM
> +	depends on ARCH_SPARX5
> +	select MMC_SDHCI_IO_ACCESSORS
> +	help
> +	  This selects the Secure Digital Host Controller Interface (SDHCI)
> +	  found in the MCHP Sparx5 SoC.
> +
> +	  If you have a Sparx5 SoC with this interface, say Y or M here.
> +
> +	  If unsure, say N.
> +
>  config MMC_SDHCI_CADENCE
>  	tristate "SDHCI support for the Cadence SD/SDIO/eMMC controller"
>  	depends on MMC_SDHCI_PLTFM
> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
> index 4d5bcb0144a0a..451c25fc2c692 100644
> --- a/drivers/mmc/host/Makefile
> +++ b/drivers/mmc/host/Makefile
> @@ -94,6 +94,7 @@ obj-$(CONFIG_MMC_SDHCI_OF_AT91)		+= sdhci-of-at91.o
>  obj-$(CONFIG_MMC_SDHCI_OF_ESDHC)	+= sdhci-of-esdhc.o
>  obj-$(CONFIG_MMC_SDHCI_OF_HLWD)		+= sdhci-of-hlwd.o
>  obj-$(CONFIG_MMC_SDHCI_OF_DWCMSHC)	+= sdhci-of-dwcmshc.o
> +obj-$(CONFIG_MMC_SDHCI_OF_SPARX5)	+= sdhci-of-sparx5.o
>  obj-$(CONFIG_MMC_SDHCI_BCM_KONA)	+= sdhci-bcm-kona.o
>  obj-$(CONFIG_MMC_SDHCI_IPROC)		+= sdhci-iproc.o
>  obj-$(CONFIG_MMC_SDHCI_MSM)		+= sdhci-msm.o
> diff --git a/drivers/mmc/host/sdhci-of-sparx5.c b/drivers/mmc/host/sdhci-of-sparx5.c
> new file mode 100644
> index 0000000000000..2b262c12e5530
> --- /dev/null
> +++ b/drivers/mmc/host/sdhci-of-sparx5.c
> @@ -0,0 +1,269 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * drivers/mmc/host/sdhci-of-sparx5.c
> + *
> + * MCHP Sparx5 SoC Secure Digital Host Controller Interface.
> + *
> + * Copyright (c) 2019 Microchip Inc.
> + *
> + * Author: Lars Povlsen <lars.povlsen@microchip.com>
> + */
> +
> +#include <linux/sizes.h>
> +#include <linux/delay.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/of_device.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/dma-mapping.h>
> +
> +#include "sdhci-pltfm.h"
> +
> +#define CPU_REGS_GENERAL_CTRL	(0x22 * 4)
> +#define  MSHC_DLY_CC_MASK	GENMASK(16, 13)
> +#define  MSHC_DLY_CC_SHIFT	13
> +#define  MSHC_DLY_CC_MAX	15
> +
> +#define CPU_REGS_PROC_CTRL	(0x2C * 4)
> +#define  ACP_CACHE_FORCE_ENA	BIT(4)
> +#define  ACP_AWCACHE		BIT(3)
> +#define  ACP_ARCACHE		BIT(2)
> +#define  ACP_CACHE_MASK		(ACP_CACHE_FORCE_ENA|ACP_AWCACHE|ACP_ARCACHE)
> +
> +#define MSHC2_VERSION			0x500	/* Off 0x140, reg 0x0 */
> +#define MSHC2_TYPE			0x504	/* Off 0x140, reg 0x1 */
> +#define MSHC2_EMMC_CTRL			0x52c	/* Off 0x140, reg 0xB */
> +#define  MSHC2_EMMC_CTRL_EMMC_RST_N	BIT(2)
> +#define  MSHC2_EMMC_CTRL_IS_EMMC	BIT(0)
> +
> +struct sdhci_sparx5_data {
> +	struct sdhci_host *host;
> +	struct regmap *cpu_ctrl;
> +	int delay_clock;
> +};
> +
> +#define BOUNDARY_OK(addr, len) \
> +	((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1)))
> +
> +/*
> + * If DMA addr spans 128MB boundary, we split the DMA transfer into two
> + * so that each DMA transfer doesn't exceed the boundary.
> + */
> +static void sdhci_sparx5_adma_write_desc(struct sdhci_host *host, void **desc,
> +					  dma_addr_t addr, int len,
> +					  unsigned int cmd)
> +{
> +	int tmplen, offset;
> +
> +	if (likely(!len || BOUNDARY_OK(addr, len))) {
> +		sdhci_adma_write_desc(host, desc, addr, len, cmd);
> +		return;
> +	}
> +
> +	pr_debug("%s: write_desc: splitting dma len %d, offset 0x%0llx\n",
> +		 mmc_hostname(host->mmc), len, addr);
> +
> +	offset = addr & (SZ_128M - 1);
> +	tmplen = SZ_128M - offset;
> +	sdhci_adma_write_desc(host, desc, addr, tmplen, cmd);
> +
> +	addr += tmplen;
> +	len -= tmplen;
> +	sdhci_adma_write_desc(host, desc, addr, len, cmd);
> +}
> +
> +static void sparx5_set_cacheable(struct sdhci_host *host, u32 value)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_sparx5_data *sdhci_sparx5 = sdhci_pltfm_priv(pltfm_host);
> +
> +	pr_debug("%s: Set Cacheable = 0x%x\n", mmc_hostname(host->mmc), value);
> +
> +	/* Update ACP caching attributes in HW */
> +	regmap_update_bits(sdhci_sparx5->cpu_ctrl,
> +			   CPU_REGS_PROC_CTRL, ACP_CACHE_MASK, value);
> +}
> +
> +static void sparx5_set_delay(struct sdhci_host *host, u8 value)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_sparx5_data *sdhci_sparx5 = sdhci_pltfm_priv(pltfm_host);
> +
> +	pr_debug("%s: Set DLY_CC = %u\n", mmc_hostname(host->mmc), value);
> +
> +	/* Update DLY_CC in HW */
> +	regmap_update_bits(sdhci_sparx5->cpu_ctrl,
> +			   CPU_REGS_GENERAL_CTRL,
> +			   MSHC_DLY_CC_MASK,
> +			   (value << MSHC_DLY_CC_SHIFT));
> +}
> +
> +static void sdhci_sparx5_set_emmc(struct sdhci_host *host)
> +{
> +	if (!mmc_card_is_removable(host->mmc)) {
> +		u8 value;
> +
> +		value = sdhci_readb(host, MSHC2_EMMC_CTRL);
> +		if (!(value & MSHC2_EMMC_CTRL_IS_EMMC)) {
> +			value |= MSHC2_EMMC_CTRL_IS_EMMC;
> +			pr_debug("%s: Set EMMC_CTRL: 0x%08x\n",
> +				 mmc_hostname(host->mmc), value);
> +			sdhci_writeb(host, value, MSHC2_EMMC_CTRL);
> +		}
> +	}
> +}
> +
> +static void sdhci_sparx5_reset_emmc(struct sdhci_host *host)
> +{
> +	u8 value;
> +
> +	pr_debug("%s: Toggle EMMC_CTRL.EMMC_RST_N\n", mmc_hostname(host->mmc));
> +	value = sdhci_readb(host, MSHC2_EMMC_CTRL) &
> +		~MSHC2_EMMC_CTRL_EMMC_RST_N;
> +	sdhci_writeb(host, value, MSHC2_EMMC_CTRL);
> +	/* For eMMC, minimum is 1us but give it 10us for good measure */
> +	usleep_range(10, 20);
> +	sdhci_writeb(host, value | MSHC2_EMMC_CTRL_EMMC_RST_N,
> +		     MSHC2_EMMC_CTRL);
> +	/* For eMMC, minimum is 200us but give it 300us for good measure */
> +	usleep_range(300, 400);
> +}
> +
> +static void sdhci_sparx5_reset(struct sdhci_host *host, u8 mask)
> +{
> +	pr_debug("%s: *** RESET: mask %d\n", mmc_hostname(host->mmc), mask);
> +
> +	sdhci_reset(host, mask);
> +
> +	/* Be sure CARD_IS_EMMC stays set */
> +	sdhci_sparx5_set_emmc(host);
> +}
> +
> +static const struct sdhci_ops sdhci_sparx5_ops = {
> +	.set_clock		= sdhci_set_clock,
> +	.set_bus_width		= sdhci_set_bus_width,
> +	.set_uhs_signaling	= sdhci_set_uhs_signaling,
> +	.get_max_clock		= sdhci_pltfm_clk_get_max_clock,
> +	.reset			= sdhci_sparx5_reset,
> +	.adma_write_desc	= sdhci_sparx5_adma_write_desc,
> +};
> +
> +static const struct sdhci_pltfm_data sdhci_sparx5_pdata = {
> +	.quirks  = 0,
> +	.quirks2 = SDHCI_QUIRK2_HOST_NO_CMD23 | /* Controller issue */
> +		   SDHCI_QUIRK2_NO_1_8_V, /* No sdr104, ddr50, etc */
> +	.ops = &sdhci_sparx5_ops,
> +};
> +
> +int sdhci_sparx5_probe(struct platform_device *pdev)
> +{
> +	int ret;
> +	const char *syscon = "microchip,sparx5-cpu-syscon";
> +	struct sdhci_host *host;
> +	struct sdhci_pltfm_host *pltfm_host;
> +	struct sdhci_sparx5_data *sdhci_sparx5;
> +	struct device_node *np = pdev->dev.of_node;
> +	u32 value;
> +	u32 extra;
> +
> +	host = sdhci_pltfm_init(pdev, &sdhci_sparx5_pdata,
> +				sizeof(*sdhci_sparx5));
> +
> +	if (IS_ERR(host))
> +		return PTR_ERR(host);
> +
> +	/*
> +	 * extra adma table cnt for cross 128M boundary handling.
> +	 */
> +	extra = DIV_ROUND_UP_ULL(dma_get_required_mask(&pdev->dev), SZ_128M);
> +	if (extra > SDHCI_MAX_SEGS)
> +		extra = SDHCI_MAX_SEGS;
> +	host->adma_table_cnt += extra;
> +
> +	pltfm_host = sdhci_priv(host);
> +	sdhci_sparx5 = sdhci_pltfm_priv(pltfm_host);
> +	sdhci_sparx5->host = host;
> +
> +	pltfm_host->clk = devm_clk_get(&pdev->dev, "core");
> +	if (IS_ERR(pltfm_host->clk)) {
> +		ret = PTR_ERR(pltfm_host->clk);
> +		dev_err(&pdev->dev, "failed to get core clk: %d\n", ret);
> +		goto free_pltfm;
> +	}
> +	ret = clk_prepare_enable(pltfm_host->clk);
> +	if (ret)
> +		goto free_pltfm;
> +
> +	if (!of_property_read_u32(np, "microchip,clock-delay", &value) &&
> +	    (value > 0 && value <= MSHC_DLY_CC_MAX))
> +		sdhci_sparx5->delay_clock = value;
> +
> +	sdhci_get_of_property(pdev);
> +
> +	ret = mmc_of_parse(host->mmc);
> +	if (ret)
> +		goto err_clk;
> +
> +	sdhci_sparx5->cpu_ctrl = syscon_regmap_lookup_by_compatible(syscon);
> +	if (IS_ERR(sdhci_sparx5->cpu_ctrl)) {
> +		dev_err(&pdev->dev, "No CPU syscon regmap !\n");
> +		ret = PTR_ERR(sdhci_sparx5->cpu_ctrl);
> +		goto err_clk;
> +	}
> +
> +	if (sdhci_sparx5->delay_clock >= 0)
> +		sparx5_set_delay(host, sdhci_sparx5->delay_clock);
> +
> +	if (!mmc_card_is_removable(host->mmc)) {
> +		/* Do a HW reset of eMMC card */
> +		sdhci_sparx5_reset_emmc(host);
> +		/* Update EMMC_CTRL */
> +		sdhci_sparx5_set_emmc(host);
> +		/* If eMMC, disable SD and SDIO */
> +		host->mmc->caps2 |= (MMC_CAP2_NO_SDIO|MMC_CAP2_NO_SD);
> +	}
> +
> +	ret = sdhci_add_host(host);
> +	if (ret)
> +		goto err_clk;
> +
> +	/* Set AXI bus master to use un-cached access (for DMA) */
> +	if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA) &&
> +	    IS_ENABLED(CONFIG_DMA_DECLARE_COHERENT))
> +		sparx5_set_cacheable(host, ACP_CACHE_FORCE_ENA);
> +
> +	pr_debug("%s: SDHC version: 0x%08x\n",
> +		 mmc_hostname(host->mmc), sdhci_readl(host, MSHC2_VERSION));
> +	pr_debug("%s: SDHC type:    0x%08x\n",
> +		 mmc_hostname(host->mmc), sdhci_readl(host, MSHC2_TYPE));
> +
> +	return ret;
> +
> +err_clk:
> +	clk_disable_unprepare(pltfm_host->clk);
> +free_pltfm:
> +	sdhci_pltfm_free(pdev);
> +	return ret;
> +}
> +
> +static const struct of_device_id sdhci_sparx5_of_match[] = {
> +	{ .compatible = "microchip,dw-sparx5-sdhci" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, sdhci_sparx5_of_match);
> +
> +static struct platform_driver sdhci_sparx5_driver = {
> +	.driver = {
> +		.name = "sdhci-sparx5",
> +		.of_match_table = sdhci_sparx5_of_match,
> +		.pm = &sdhci_pltfm_pmops,
> +	},
> +	.probe = sdhci_sparx5_probe,
> +	.remove = sdhci_pltfm_unregister,
> +};
> +
> +module_platform_driver(sdhci_sparx5_driver);
> +
> +MODULE_DESCRIPTION("Sparx5 SDHCI OF driver");
> +MODULE_AUTHOR("Lars Povlsen <lars.povlsen@microchip.com>");
> +MODULE_LICENSE("GPL v2");
> 


  reply	other threads:[~2020-06-18 14:46 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-06-18 14:13 [PATCH v4 0/3] mmc: Adding support for Microchip Sparx5 SoC Lars Povlsen
2020-06-18 14:13 ` [PATCH v4 1/3] dt-bindings: mmc: Add Sparx5 SDHCI controller bindings Lars Povlsen
2020-06-29 21:54   ` Rob Herring
2020-06-18 14:13 ` [PATCH v4 2/3] sdhci: sparx5: Add Sparx5 SoC eMMC driver Lars Povlsen
2020-06-18 14:43   ` Adrian Hunter [this message]
2020-07-22 11:54     ` Lars Povlsen
2020-07-24 10:47       ` Ulf Hansson
2020-07-24 11:32         ` Lars Povlsen
2020-07-24 12:43           ` Ulf Hansson
2020-06-18 14:13 ` [PATCH v4 3/3] arm64: dts: sparx5: Add Sparx5 eMMC support Lars Povlsen
2020-08-24 15:10 [PATCH v4 0/3] mmc: Adding support for Microchip Sparx5 SoC Lars Povlsen
2020-08-24 15:10 ` [PATCH v4 2/3] sdhci: sparx5: Add Sparx5 SoC eMMC driver Lars Povlsen
2020-08-24 15:50   ` Adrian Hunter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=aee90bbf-f0ff-b0cb-b10a-9a2f3bb6acca@intel.com \
    --to=adrian.hunter@intel.com \
    --cc=UNGLinuxDriver@microchip.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=devicetree@vger.kernel.org \
    --cc=lars.povlsen@microchip.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=soc@kernel.org \
    --cc=ulf.hansson@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).