[PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[Paul Cercueil]

Add compatible strings to probe the jz4780-nand and jz4780-bch drivers
from devicetree on the JZ4725B and JZ4740 SoCs from Ingenic.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

Changes:

v2: - Change 'ingenic,jz4725b-nand' compatible string to
      'ingenic,jz4740-nand' to reflect driver change
    - Add 'ingenic,jz4740-bch' compatible string
    - Document 'ingenic,oob-layout' property

v3: - Removed 'ingenic,oob-layout' property
    - Update compatible strings to what the driver supports

v4: No change

 Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
index 29ea5853ca91..a5b940f18bf6 100644
--- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
@@ -6,7 +6,10 @@ memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
 be children of the NEMC node.
 
 Required NAND controller device properties:
-- compatible: Should be set to "ingenic,jz4780-nand".
+- compatible: Should be one of:
+  * ingenic,jz4740-nand
+  * ingenic,jz4725b-nand
+  * ingenic,jz4780-nand
 - reg: For each bank with a NAND chip attached, should specify a bank number,
   an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
 
@@ -72,7 +75,10 @@ NAND devices. The following is a description of the device properties for a
 BCH controller.
 
 Required BCH properties:
-- compatible: Should be set to "ingenic,jz4780-bch".
+- compatible: Should be one of:
+  * ingenic,jz4740-ecc
+  * ingenic,jz4725b-bch
+  * ingenic,jz4780-bch
 - reg: Should specify the BCH controller registers location and length.
 - clocks: Clock for the BCH controller.
 
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 2/9] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Paul Cercueil]

The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes more
sense to use the more generic ECC term.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

Changes:

v3: New patch

v4: No change

 .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
index a5b940f18bf6..5a45cc54f46d 100644
--- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
@@ -1,4 +1,4 @@
-* Ingenic JZ4780 NAND/BCH
+* Ingenic JZ4780 NAND/ECC
 
 This file documents the device tree bindings for NAND flash devices on the
 JZ4780. NAND devices are connected to the NEMC controller (described in
@@ -14,10 +14,10 @@ Required NAND controller device properties:
   an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
 
 Optional NAND controller device properties:
-- ingenic,bch-controller: To make use of the hardware BCH controller, this
-  property must contain a phandle for the BCH controller node. The required
+- ingenic,bch-controller: To make use of the hardware ECC controller, this
+  property must contain a phandle for the ECC controller node. The required
   properties for this node are described below. If this is not specified,
-  software BCH will be used instead.
+  software ECC will be used instead.
 
 Optional children nodes:
 - Individual NAND chips are children of the NAND controller node.
@@ -70,17 +70,17 @@ nemc: nemc@13410000 {
 	};
 };
 
-The BCH controller is a separate SoC component used for error correction on
+The ECC controller is a separate SoC component used for error correction on
 NAND devices. The following is a description of the device properties for a
-BCH controller.
+ECC controller.
 
-Required BCH properties:
+Required ECC properties:
 - compatible: Should be one of:
   * ingenic,jz4740-ecc
   * ingenic,jz4725b-bch
   * ingenic,jz4780-bch
-- reg: Should specify the BCH controller registers location and length.
-- clocks: Clock for the BCH controller.
+- reg: Should specify the ECC controller registers location and length.
+- clocks: Clock for the ECC controller.
 
 Example:
 
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 2/9] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Rob Herring]

On Sat,  9 Feb 2019 16:22:58 -0300, Paul Cercueil wrote:
> The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes more
> sense to use the more generic ECC term.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> Changes:
> 
> v3: New patch
> 
> v4: No change
> 
>  .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 +++++++++---------
>  1 file changed, 9 insertions(+), 9 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 2/9] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Sat,  9 Feb 2019 16:22:58
-0300:

> The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes more
> sense to use the more generic ECC term.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> Changes:
> 
> v3: New patch
> 
> v4: No change
> 
>  .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 +++++++++---------
>  1 file changed, 9 insertions(+), 9 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> index a5b940f18bf6..5a45cc54f46d 100644
> --- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> @@ -1,4 +1,4 @@
> -* Ingenic JZ4780 NAND/BCH
> +* Ingenic JZ4780 NAND/ECC
>  
>  This file documents the device tree bindings for NAND flash devices on the
>  JZ4780. NAND devices are connected to the NEMC controller (described in
> @@ -14,10 +14,10 @@ Required NAND controller device properties:
>    an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
>  
>  Optional NAND controller device properties:
> -- ingenic,bch-controller: To make use of the hardware BCH controller, this
> -  property must contain a phandle for the BCH controller node. The required
> +- ingenic,bch-controller: To make use of the hardware ECC controller, this
> +  property must contain a phandle for the ECC controller node. The required

I think there is already a 'ecc-engine' property used by MTK and Atmel
NAND controllers to point to the ECC engine block. Please use this
property instead of the ingenic specific one.

>    properties for this node are described below. If this is not specified,
> -  software BCH will be used instead.
> +  software ECC will be used instead.
>  
>  Optional children nodes:
>  - Individual NAND chips are children of the NAND controller node.
> @@ -70,17 +70,17 @@ nemc: nemc@13410000 {
>  	};
>  };
>  
> -The BCH controller is a separate SoC component used for error correction on
> +The ECC controller is a separate SoC component used for error correction on
>  NAND devices. The following is a description of the device properties for a
> -BCH controller.
> +ECC controller.
>  
> -Required BCH properties:
> +Required ECC properties:
>  - compatible: Should be one of:
>    * ingenic,jz4740-ecc
>    * ingenic,jz4725b-bch
>    * ingenic,jz4780-bch
> -- reg: Should specify the BCH controller registers location and length.
> -- clocks: Clock for the BCH controller.
> +- reg: Should specify the ECC controller registers location and length.
> +- clocks: Clock for the ECC controller.
>  
>  Example:
>  

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 2/9] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Paul Cercueil]

On Mon, Mar 4, 2019 at 10:50 AM, Miquel Raynal 
<miquel.raynal@bootlin.com> wrote:
> Hi Paul,
> 
> Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> 
> wrote on Sat,  9 Feb 2019 16:22:58
> -0300:
> 
>>  The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes 
>> more
>>  sense to use the more generic ECC term.
>> 
>>  Signed-off-by: Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>>
>>  ---
>> 
>>  Changes:
>> 
>>  v3: New patch
>> 
>>  v4: No change
>> 
>>   .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 
>> +++++++++---------
>>   1 file changed, 9 insertions(+), 9 deletions(-)
>> 
>>  diff --git 
>> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt 
>> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  index a5b940f18bf6..5a45cc54f46d 100644
>>  --- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  @@ -1,4 +1,4 @@
>>  -* Ingenic JZ4780 NAND/BCH
>>  +* Ingenic JZ4780 NAND/ECC
>> 
>>   This file documents the device tree bindings for NAND flash 
>> devices on the
>>   JZ4780. NAND devices are connected to the NEMC controller 
>> (described in
>>  @@ -14,10 +14,10 @@ Required NAND controller device properties:
>>     an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC 
>> bank).
>> 
>>   Optional NAND controller device properties:
>>  -- ingenic,bch-controller: To make use of the hardware BCH 
>> controller, this
>>  -  property must contain a phandle for the BCH controller node. The 
>> required
>>  +- ingenic,bch-controller: To make use of the hardware ECC 
>> controller, this
>>  +  property must contain a phandle for the ECC controller node. The 
>> required
> 
> I think there is already a 'ecc-engine' property used by MTK and Atmel
> NAND controllers to point to the ECC engine block. Please use this
> property instead of the ingenic specific one.

ingenic,bch-controller is already in the devicetree ABI. I can't change 
it now...

>>     properties for this node are described below. If this is not 
>> specified,
>>  -  software BCH will be used instead.
>>  +  software ECC will be used instead.
>> 
>>   Optional children nodes:
>>   - Individual NAND chips are children of the NAND controller node.
>>  @@ -70,17 +70,17 @@ nemc: nemc@13410000 {
>>   	};
>>   };
>> 
>>  -The BCH controller is a separate SoC component used for error 
>> correction on
>>  +The ECC controller is a separate SoC component used for error 
>> correction on
>>   NAND devices. The following is a description of the device 
>> properties for a
>>  -BCH controller.
>>  +ECC controller.
>> 
>>  -Required BCH properties:
>>  +Required ECC properties:
>>   - compatible: Should be one of:
>>     * ingenic,jz4740-ecc
>>     * ingenic,jz4725b-bch
>>     * ingenic,jz4780-bch
>>  -- reg: Should specify the BCH controller registers location and 
>> length.
>>  -- clocks: Clock for the BCH controller.
>>  +- reg: Should specify the ECC controller registers location and 
>> length.
>>  +- clocks: Clock for the ECC controller.
>> 
>>   Example:
>> 
> 
> Thanks,
> Miquèl



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 2/9] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Mon, 04 Mar 2019 19:23:50
+0100:

> On Mon, Mar 4, 2019 at 10:50 AM, Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> > Hi Paul,
> > 
> > Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> > wrote on Sat,  9 Feb 2019 16:22:58
> > -0300:
> >   
> >>  The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes >> more
> >>  sense to use the more generic ECC term.  
> >> >>  Signed-off-by: Paul Cercueil <paul@crapouillou.net >> <mailto:paul@crapouillou.net>>  
> >>  ---  
> >> >>  Changes:
> >> >>  v3: New patch
> >> >>  v4: No change
> >> >>   .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 >> +++++++++---------  
> >>   1 file changed, 9 insertions(+), 9 deletions(-)  
> >> >>  diff --git >> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt >> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt  
> >>  index a5b940f18bf6..5a45cc54f46d 100644
> >>  --- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> >>  +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> >>  @@ -1,4 +1,4 @@
> >>  -* Ingenic JZ4780 NAND/BCH
> >>  +* Ingenic JZ4780 NAND/ECC  
> >> >>   This file documents the device tree bindings for NAND flash >> devices on the  
> >>   JZ4780. NAND devices are connected to the NEMC controller >> (described in
> >>  @@ -14,10 +14,10 @@ Required NAND controller device properties:
> >>     an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC >> bank).  
> >> >>   Optional NAND controller device properties:  
> >>  -- ingenic,bch-controller: To make use of the hardware BCH >> controller, this
> >>  -  property must contain a phandle for the BCH controller node. The >> required
> >>  +- ingenic,bch-controller: To make use of the hardware ECC >> controller, this
> >>  +  property must contain a phandle for the ECC controller node. The >> required  
> > 
> > I think there is already a 'ecc-engine' property used by MTK and Atmel
> > NAND controllers to point to the ECC engine block. Please use this
> > property instead of the ingenic specific one.  
> 
> ingenic,bch-controller is already in the devicetree ABI. I can't change it now...

Oh, right...

Well, same thing as before, maybe you can change it and keep the driver
backward compatible? I don't want new DT to use this property because
it is not generic and we must have a way from the core to find the ECC
engine handle when the controller does not embed one itself (thus, the
ecc-engine property which is around for quite some time already).

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 2/9] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Paul Cercueil]

Le lun. 4 mars 2019 à 15:58, Miquel Raynal <miquel.raynal@bootlin.com> 
a écrit :
> Hi Paul,
> 
> Paul Cercueil <paul@crapouillou.net> wrote on Mon, 04 Mar 2019 
> 19:23:50
> +0100:
> 
>>  On Mon, Mar 4, 2019 at 10:50 AM, Miquel Raynal 
>> <miquel.raynal@bootlin.com> wrote:
>>  > Hi Paul,
>>  >
>>  > Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>> > wrote on Sat,  9 Feb 2019 16:22:58
>>  > -0300:
>>  >
>>  >>  The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it 
>> makes >> more
>>  >>  sense to use the more generic ECC term.
>>  >> >>  Signed-off-by: Paul Cercueil <paul@crapouillou.net >> 
>> <mailto:paul@crapouillou.net>>
>>  >>  ---
>>  >> >>  Changes:
>>  >> >>  v3: New patch
>>  >> >>  v4: No change
>>  >> >>   .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 
>> >> +++++++++---------
>>  >>   1 file changed, 9 insertions(+), 9 deletions(-)
>>  >> >>  diff --git >> 
>> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt >> 
>> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  >>  index a5b940f18bf6..5a45cc54f46d 100644
>>  >>  --- 
>> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  >>  +++ 
>> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  >>  @@ -1,4 +1,4 @@
>>  >>  -* Ingenic JZ4780 NAND/BCH
>>  >>  +* Ingenic JZ4780 NAND/ECC
>>  >> >>   This file documents the device tree bindings for NAND flash 
>> >> devices on the
>>  >>   JZ4780. NAND devices are connected to the NEMC controller >> 
>> (described in
>>  >>  @@ -14,10 +14,10 @@ Required NAND controller device properties:
>>  >>     an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC 
>> >> bank).
>>  >> >>   Optional NAND controller device properties:
>>  >>  -- ingenic,bch-controller: To make use of the hardware BCH >> 
>> controller, this
>>  >>  -  property must contain a phandle for the BCH controller node. 
>> The >> required
>>  >>  +- ingenic,bch-controller: To make use of the hardware ECC >> 
>> controller, this
>>  >>  +  property must contain a phandle for the ECC controller node. 
>> The >> required
>>  >
>>  > I think there is already a 'ecc-engine' property used by MTK and 
>> Atmel
>>  > NAND controllers to point to the ECC engine block. Please use this
>>  > property instead of the ingenic specific one.
>> 
>>  ingenic,bch-controller is already in the devicetree ABI. I can't 
>> change it now...
> 
> Oh, right...
> 
> Well, same thing as before, maybe you can change it and keep the 
> driver
> backward compatible? I don't want new DT to use this property because
> it is not generic and we must have a way from the core to find the ECC
> engine handle when the controller does not embed one itself (thus, the
> ecc-engine property which is around for quite some time already).

I can do that. Will the new ECC framework work with the "ecc-engine" 
property?

-Paul


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 2/9] dt-bindings: mtd: ingenic: Change 'BCH' to 'ECC' in documentation

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Wed, 13 Mar 2019 09:59:48
-0300:

> Le lun. 4 mars 2019 à 15:58, Miquel Raynal <miquel.raynal@bootlin.com> a écrit :
> > Hi Paul,
> > 
> > Paul Cercueil <paul@crapouillou.net> wrote on Mon, 04 Mar 2019 > 19:23:50
> > +0100:
> >   
> >>  On Mon, Mar 4, 2019 at 10:50 AM, Miquel Raynal >> <miquel.raynal@bootlin.com> wrote:  
> >>  > Hi Paul,
> >>  >
> >>  > Paul Cercueil <paul@crapouillou.net >> <mailto:paul@crapouillou.net>> > wrote on Sat,  9 Feb 2019 16:22:58
> >>  > -0300:
> >>  >  
> >>  >>  The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it >> makes >> more
> >>  >>  sense to use the more generic ECC term.  
> >>  >> >>  Signed-off-by: Paul Cercueil <paul@crapouillou.net >> >> <mailto:paul@crapouillou.net>>  
> >>  >>  ---  
> >>  >> >>  Changes:
> >>  >> >>  v3: New patch
> >>  >> >>  v4: No change
> >>  >> >>   .../devicetree/bindings/mtd/ingenic,jz4780-nand.txt    | 18 >> >> +++++++++---------  
> >>  >>   1 file changed, 9 insertions(+), 9 deletions(-)  
> >>  >> >>  diff --git >> >> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt >> >> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt  
> >>  >>  index a5b940f18bf6..5a45cc54f46d 100644  
> >>  >>  --- >> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt  
> >>  >>  +++ >> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> >>  >>  @@ -1,4 +1,4 @@
> >>  >>  -* Ingenic JZ4780 NAND/BCH
> >>  >>  +* Ingenic JZ4780 NAND/ECC  
> >>  >> >>   This file documents the device tree bindings for NAND flash >> >> devices on the  
> >>  >>   JZ4780. NAND devices are connected to the NEMC controller >> >> (described in
> >>  >>  @@ -14,10 +14,10 @@ Required NAND controller device properties:
> >>  >>     an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC >> >> bank).  
> >>  >> >>   Optional NAND controller device properties:  
> >>  >>  -- ingenic,bch-controller: To make use of the hardware BCH >> >> controller, this
> >>  >>  -  property must contain a phandle for the BCH controller node. >> The >> required
> >>  >>  +- ingenic,bch-controller: To make use of the hardware ECC >> >> controller, this
> >>  >>  +  property must contain a phandle for the ECC controller node. >> The >> required  
> >>  >
> >>  > I think there is already a 'ecc-engine' property used by MTK and >> Atmel
> >>  > NAND controllers to point to the ECC engine block. Please use this
> >>  > property instead of the ingenic specific one.  
> >> >>  ingenic,bch-controller is already in the devicetree ABI. I can't >> change it now...  
> > 
> > Oh, right...
> > 
> > Well, same thing as before, maybe you can change it and keep the > driver
> > backward compatible? I don't want new DT to use this property because
> > it is not generic and we must have a way from the core to find the ECC
> > engine handle when the controller does not embed one itself (thus, the
> > ecc-engine property which is around for quite some time already).  
> 
> I can do that. Will the new ECC framework work with the "ecc-engine" property?

Yes.

Right now it does not, but when supporting raw NAND devices, it will
have to.


Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 3/9] mtd: rawnand: Move drivers for Ingenic SoCs to subfolder

[Paul Cercueil]

Before adding support for more SoCs and seeing the number of files for
these drivers grow, we move them to their own subfolder to keep it tidy.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

Changes:

v2: New patch

v3: No change

v4: No change

 drivers/mtd/nand/raw/Kconfig                     | 14 +-------------
 drivers/mtd/nand/raw/Makefile                    |  3 +--
 drivers/mtd/nand/raw/ingenic/Kconfig             | 13 +++++++++++++
 drivers/mtd/nand/raw/ingenic/Makefile            |  2 ++
 drivers/mtd/nand/raw/{ => ingenic}/jz4740_nand.c |  0
 drivers/mtd/nand/raw/{ => ingenic}/jz4780_bch.c  |  0
 drivers/mtd/nand/raw/{ => ingenic}/jz4780_bch.h  |  0
 drivers/mtd/nand/raw/{ => ingenic}/jz4780_nand.c |  0
 8 files changed, 17 insertions(+), 15 deletions(-)
 create mode 100644 drivers/mtd/nand/raw/ingenic/Kconfig
 create mode 100644 drivers/mtd/nand/raw/ingenic/Makefile
 rename drivers/mtd/nand/raw/{ => ingenic}/jz4740_nand.c (100%)
 rename drivers/mtd/nand/raw/{ => ingenic}/jz4780_bch.c (100%)
 rename drivers/mtd/nand/raw/{ => ingenic}/jz4780_bch.h (100%)
 rename drivers/mtd/nand/raw/{ => ingenic}/jz4780_nand.c (100%)

diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 1a55d3e3d4c5..d886be2fc174 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -470,19 +470,7 @@ config MTD_NAND_NUC900
 	  This enables the driver for the NAND Flash on evaluation board based
 	  on w90p910 / NUC9xx.
 
-config MTD_NAND_JZ4740
-	tristate "Support for JZ4740 SoC NAND controller"
-	depends on MACH_JZ4740 || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  Enables support for NAND Flash on JZ4740 SoC based boards.
-
-config MTD_NAND_JZ4780
-	tristate "Support for NAND on JZ4780 SoC"
-	depends on JZ4780_NEMC
-	help
-	  Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
-	  based boards, using the BCH controller for hardware error correction.
+source "drivers/mtd/nand/raw/ingenic/Kconfig"
 
 config MTD_NAND_FSMC
 	tristate "Support for NAND on ST Micros FSMC"
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
index 57159b349054..f419d373d090 100644
--- a/drivers/mtd/nand/raw/Makefile
+++ b/drivers/mtd/nand/raw/Makefile
@@ -45,8 +45,7 @@ obj-$(CONFIG_MTD_NAND_NUC900)		+= nuc900_nand.o
 obj-$(CONFIG_MTD_NAND_MPC5121_NFC)	+= mpc5121_nfc.o
 obj-$(CONFIG_MTD_NAND_VF610_NFC)	+= vf610_nfc.o
 obj-$(CONFIG_MTD_NAND_RICOH)		+= r852.o
-obj-$(CONFIG_MTD_NAND_JZ4740)		+= jz4740_nand.o
-obj-$(CONFIG_MTD_NAND_JZ4780)		+= jz4780_nand.o jz4780_bch.o
+obj-y					+= ingenic/
 obj-$(CONFIG_MTD_NAND_GPMI_NAND)	+= gpmi-nand/
 obj-$(CONFIG_MTD_NAND_XWAY)		+= xway_nand.o
 obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH)	+= bcm47xxnflash/
diff --git a/drivers/mtd/nand/raw/ingenic/Kconfig b/drivers/mtd/nand/raw/ingenic/Kconfig
new file mode 100644
index 000000000000..67806c87b2c4
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/Kconfig
@@ -0,0 +1,13 @@
+config MTD_NAND_JZ4740
+	tristate "Support for JZ4740 SoC NAND controller"
+	depends on MACH_JZ4740 || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  Enables support for NAND Flash on JZ4740 SoC based boards.
+
+config MTD_NAND_JZ4780
+	tristate "Support for NAND on JZ4780 SoC"
+	depends on JZ4780_NEMC
+	help
+	  Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
+	  based boards, using the BCH controller for hardware error correction.
diff --git a/drivers/mtd/nand/raw/ingenic/Makefile b/drivers/mtd/nand/raw/ingenic/Makefile
new file mode 100644
index 000000000000..44c2ca053d24
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
+obj-$(CONFIG_MTD_NAND_JZ4780) += jz4780_nand.o jz4780_bch.o
diff --git a/drivers/mtd/nand/raw/jz4740_nand.c b/drivers/mtd/nand/raw/ingenic/jz4740_nand.c
similarity index 100%
rename from drivers/mtd/nand/raw/jz4740_nand.c
rename to drivers/mtd/nand/raw/ingenic/jz4740_nand.c
diff --git a/drivers/mtd/nand/raw/jz4780_bch.c b/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
similarity index 100%
rename from drivers/mtd/nand/raw/jz4780_bch.c
rename to drivers/mtd/nand/raw/ingenic/jz4780_bch.c
diff --git a/drivers/mtd/nand/raw/jz4780_bch.h b/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
similarity index 100%
rename from drivers/mtd/nand/raw/jz4780_bch.h
rename to drivers/mtd/nand/raw/ingenic/jz4780_bch.h
diff --git a/drivers/mtd/nand/raw/jz4780_nand.c b/drivers/mtd/nand/raw/ingenic/jz4780_nand.c
similarity index 100%
rename from drivers/mtd/nand/raw/jz4780_nand.c
rename to drivers/mtd/nand/raw/ingenic/jz4780_nand.c
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 4/9] mtd: rawnand: ingenic: Use SPDX license notifiers

[Paul Cercueil]

Use SPDX license notifiers instead of GPLv2 license text in the headers.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
---

v2: No changes

v3: No changes

v4: No changes

 drivers/mtd/nand/raw/ingenic/jz4780_bch.c  | 5 +----
 drivers/mtd/nand/raw/ingenic/jz4780_bch.h  | 5 +----
 drivers/mtd/nand/raw/ingenic/jz4780_nand.c | 5 +----
 3 files changed, 3 insertions(+), 12 deletions(-)

diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_bch.c b/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
index 7201827809e9..7e4e5e627603 100644
--- a/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
+++ b/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * JZ4780 BCH controller
  *
  * Copyright (c) 2015 Imagination Technologies
  * Author: Alex Smith <alex.smith@imgtec.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
  */
 
 #include <linux/bitops.h>
diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_bch.h b/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
index bf4718088a3a..451e0c770160 100644
--- a/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
+++ b/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
@@ -1,12 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
 /*
  * JZ4780 BCH controller
  *
  * Copyright (c) 2015 Imagination Technologies
  * Author: Alex Smith <alex.smith@imgtec.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
  */
 
 #ifndef __DRIVERS_MTD_NAND_JZ4780_BCH_H__
diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_nand.c b/drivers/mtd/nand/raw/ingenic/jz4780_nand.c
index 22e58975f0d5..7f55358b860f 100644
--- a/drivers/mtd/nand/raw/ingenic/jz4780_nand.c
+++ b/drivers/mtd/nand/raw/ingenic/jz4780_nand.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * JZ4780 NAND driver
  *
  * Copyright (c) 2015 Imagination Technologies
  * Author: Alex Smith <alex.smith@imgtec.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
  */
 
 #include <linux/delay.h>
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 5/9] mtd: rawnand: ingenic: Rename jz4780_nand driver to ingenic_nand

[Paul Cercueil]

The jz4780_nand driver will be modified to handle all the Ingenic
JZ47xx SoCs that the upstream Linux kernel supports (JZ4740, JZ4725B,
JZ4770, JZ4780), so it makes sense to rename it.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

v3: New patch

v4: No changes

 drivers/mtd/nand/raw/ingenic/Makefile              |   2 +-
 .../raw/ingenic/{jz4780_nand.c => ingenic_nand.c}  | 146 ++++++++++-----------
 2 files changed, 74 insertions(+), 74 deletions(-)
 rename drivers/mtd/nand/raw/ingenic/{jz4780_nand.c => ingenic_nand.c} (63%)

diff --git a/drivers/mtd/nand/raw/ingenic/Makefile b/drivers/mtd/nand/raw/ingenic/Makefile
index 44c2ca053d24..af2d5de21f60 100644
--- a/drivers/mtd/nand/raw/ingenic/Makefile
+++ b/drivers/mtd/nand/raw/ingenic/Makefile
@@ -1,2 +1,2 @@
 obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
-obj-$(CONFIG_MTD_NAND_JZ4780) += jz4780_nand.o jz4780_bch.o
+obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o jz4780_bch.o
diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_nand.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
similarity index 63%
rename from drivers/mtd/nand/raw/ingenic/jz4780_nand.c
rename to drivers/mtd/nand/raw/ingenic/ingenic_nand.c
index 7f55358b860f..8c73f7c5be9a 100644
--- a/drivers/mtd/nand/raw/ingenic/jz4780_nand.c
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * JZ4780 NAND driver
+ * Ingenic JZ47xx NAND driver
  *
  * Copyright (c) 2015 Imagination Technologies
  * Author: Alex Smith <alex.smith@imgtec.com>
@@ -24,7 +24,7 @@
 
 #include "jz4780_bch.h"
 
-#define DRV_NAME	"jz4780-nand"
+#define DRV_NAME	"ingenic-nand"
 
 #define OFFSET_DATA	0x00000000
 #define OFFSET_CMD	0x00400000
@@ -33,22 +33,22 @@
 /* Command delay when there is no R/B pin. */
 #define RB_DELAY_US	100
 
-struct jz4780_nand_cs {
+struct ingenic_nand_cs {
 	unsigned int bank;
 	void __iomem *base;
 };
 
-struct jz4780_nand_controller {
+struct ingenic_nfc {
 	struct device *dev;
 	struct jz4780_bch *bch;
 	struct nand_controller controller;
 	unsigned int num_banks;
 	struct list_head chips;
 	int selected;
-	struct jz4780_nand_cs cs[];
+	struct ingenic_nand_cs cs[];
 };
 
-struct jz4780_nand_chip {
+struct ingenic_nand {
 	struct nand_chip chip;
 	struct list_head chip_list;
 
@@ -57,22 +57,21 @@ struct jz4780_nand_chip {
 	unsigned int reading: 1;
 };
 
-static inline struct jz4780_nand_chip *to_jz4780_nand_chip(struct mtd_info *mtd)
+static inline struct ingenic_nand *to_ingenic_nand(struct mtd_info *mtd)
 {
-	return container_of(mtd_to_nand(mtd), struct jz4780_nand_chip, chip);
+	return container_of(mtd_to_nand(mtd), struct ingenic_nand, chip);
 }
 
-static inline struct jz4780_nand_controller
-*to_jz4780_nand_controller(struct nand_controller *ctrl)
+static inline struct ingenic_nfc *to_ingenic_nfc(struct nand_controller *ctrl)
 {
-	return container_of(ctrl, struct jz4780_nand_controller, controller);
+	return container_of(ctrl, struct ingenic_nfc, controller);
 }
 
-static void jz4780_nand_select_chip(struct nand_chip *chip, int chipnr)
+static void ingenic_nand_select_chip(struct nand_chip *chip, int chipnr)
 {
-	struct jz4780_nand_chip *nand = to_jz4780_nand_chip(nand_to_mtd(chip));
-	struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(nand->chip.controller);
-	struct jz4780_nand_cs *cs;
+	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
+	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
+	struct ingenic_nand_cs *cs;
 
 	/* Ensure the currently selected chip is deasserted. */
 	if (chipnr == -1 && nfc->selected >= 0) {
@@ -83,12 +82,12 @@ static void jz4780_nand_select_chip(struct nand_chip *chip, int chipnr)
 	nfc->selected = chipnr;
 }
 
-static void jz4780_nand_cmd_ctrl(struct nand_chip *chip, int cmd,
-				 unsigned int ctrl)
+static void ingenic_nand_cmd_ctrl(struct nand_chip *chip, int cmd,
+				  unsigned int ctrl)
 {
-	struct jz4780_nand_chip *nand = to_jz4780_nand_chip(nand_to_mtd(chip));
-	struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(nand->chip.controller);
-	struct jz4780_nand_cs *cs;
+	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
+	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
+	struct ingenic_nand_cs *cs;
 
 	if (WARN_ON(nfc->selected < 0))
 		return;
@@ -106,25 +105,25 @@ static void jz4780_nand_cmd_ctrl(struct nand_chip *chip, int cmd,
 		writeb(cmd, cs->base + OFFSET_CMD);
 }
 
-static int jz4780_nand_dev_ready(struct nand_chip *chip)
+static int ingenic_nand_dev_ready(struct nand_chip *chip)
 {
-	struct jz4780_nand_chip *nand = to_jz4780_nand_chip(nand_to_mtd(chip));
+	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
 
 	return !gpiod_get_value_cansleep(nand->busy_gpio);
 }
 
-static void jz4780_nand_ecc_hwctl(struct nand_chip *chip, int mode)
+static void ingenic_nand_ecc_hwctl(struct nand_chip *chip, int mode)
 {
-	struct jz4780_nand_chip *nand = to_jz4780_nand_chip(nand_to_mtd(chip));
+	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
 
 	nand->reading = (mode == NAND_ECC_READ);
 }
 
-static int jz4780_nand_ecc_calculate(struct nand_chip *chip, const u8 *dat,
-				     u8 *ecc_code)
+static int ingenic_nand_ecc_calculate(struct nand_chip *chip, const u8 *dat,
+				      u8 *ecc_code)
 {
-	struct jz4780_nand_chip *nand = to_jz4780_nand_chip(nand_to_mtd(chip));
-	struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(nand->chip.controller);
+	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
+	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
 	struct jz4780_bch_params params;
 
 	/*
@@ -141,11 +140,11 @@ static int jz4780_nand_ecc_calculate(struct nand_chip *chip, const u8 *dat,
 	return jz4780_bch_calculate(nfc->bch, &params, dat, ecc_code);
 }
 
-static int jz4780_nand_ecc_correct(struct nand_chip *chip, u8 *dat,
-				   u8 *read_ecc, u8 *calc_ecc)
+static int ingenic_nand_ecc_correct(struct nand_chip *chip, u8 *dat,
+				    u8 *read_ecc, u8 *calc_ecc)
 {
-	struct jz4780_nand_chip *nand = to_jz4780_nand_chip(nand_to_mtd(chip));
-	struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(nand->chip.controller);
+	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
+	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
 	struct jz4780_bch_params params;
 
 	params.size = nand->chip.ecc.size;
@@ -155,10 +154,10 @@ static int jz4780_nand_ecc_correct(struct nand_chip *chip, u8 *dat,
 	return jz4780_bch_correct(nfc->bch, &params, dat, read_ecc);
 }
 
-static int jz4780_nand_attach_chip(struct nand_chip *chip)
+static int ingenic_nand_attach_chip(struct nand_chip *chip)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
-	struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(chip->controller);
+	struct ingenic_nfc *nfc = to_ingenic_nfc(chip->controller);
 	int eccbytes;
 
 	chip->ecc.bytes = fls((1 + 8) * chip->ecc.size)	*
@@ -167,14 +166,13 @@ static int jz4780_nand_attach_chip(struct nand_chip *chip)
 	switch (chip->ecc.mode) {
 	case NAND_ECC_HW:
 		if (!nfc->bch) {
-			dev_err(nfc->dev,
-				"HW BCH selected, but BCH controller not found\n");
+			dev_err(nfc->dev, "HW BCH selected, but BCH controller not found\n");
 			return -ENODEV;
 		}
 
-		chip->ecc.hwctl = jz4780_nand_ecc_hwctl;
-		chip->ecc.calculate = jz4780_nand_ecc_calculate;
-		chip->ecc.correct = jz4780_nand_ecc_correct;
+		chip->ecc.hwctl = ingenic_nand_ecc_hwctl;
+		chip->ecc.calculate = ingenic_nand_ecc_calculate;
+		chip->ecc.correct = ingenic_nand_ecc_correct;
 		/* fall through */
 	case NAND_ECC_SOFT:
 		dev_info(nfc->dev, "using %s (strength %d, size %d, bytes %d)\n",
@@ -209,18 +207,18 @@ static int jz4780_nand_attach_chip(struct nand_chip *chip)
 	return 0;
 }
 
-static const struct nand_controller_ops jz4780_nand_controller_ops = {
-	.attach_chip = jz4780_nand_attach_chip,
+static const struct nand_controller_ops ingenic_nand_controller_ops = {
+	.attach_chip = ingenic_nand_attach_chip,
 };
 
-static int jz4780_nand_init_chip(struct platform_device *pdev,
-				struct jz4780_nand_controller *nfc,
-				struct device_node *np,
-				unsigned int chipnr)
+static int ingenic_nand_init_chip(struct platform_device *pdev,
+				  struct ingenic_nfc *nfc,
+				  struct device_node *np,
+				  unsigned int chipnr)
 {
 	struct device *dev = &pdev->dev;
-	struct jz4780_nand_chip *nand;
-	struct jz4780_nand_cs *cs;
+	struct ingenic_nand *nand;
+	struct ingenic_nand_cs *cs;
 	struct resource *res;
 	struct nand_chip *chip;
 	struct mtd_info *mtd;
@@ -253,7 +251,7 @@ static int jz4780_nand_init_chip(struct platform_device *pdev,
 		dev_err(dev, "failed to request busy GPIO: %d\n", ret);
 		return ret;
 	} else if (nand->busy_gpio) {
-		nand->chip.legacy.dev_ready = jz4780_nand_dev_ready;
+		nand->chip.legacy.dev_ready = ingenic_nand_dev_ready;
 	}
 
 	nand->wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_OUT_LOW);
@@ -276,13 +274,13 @@ static int jz4780_nand_init_chip(struct platform_device *pdev,
 	chip->legacy.IO_ADDR_W = cs->base + OFFSET_DATA;
 	chip->legacy.chip_delay = RB_DELAY_US;
 	chip->options = NAND_NO_SUBPAGE_WRITE;
-	chip->legacy.select_chip = jz4780_nand_select_chip;
-	chip->legacy.cmd_ctrl = jz4780_nand_cmd_ctrl;
+	chip->legacy.select_chip = ingenic_nand_select_chip;
+	chip->legacy.cmd_ctrl = ingenic_nand_cmd_ctrl;
 	chip->ecc.mode = NAND_ECC_HW;
 	chip->controller = &nfc->controller;
 	nand_set_flash_node(chip, np);
 
-	chip->controller->ops = &jz4780_nand_controller_ops;
+	chip->controller->ops = &ingenic_nand_controller_ops;
 	ret = nand_scan(chip, 1);
 	if (ret)
 		return ret;
@@ -298,19 +296,20 @@ static int jz4780_nand_init_chip(struct platform_device *pdev,
 	return 0;
 }
 
-static void jz4780_nand_cleanup_chips(struct jz4780_nand_controller *nfc)
+static void ingenic_nand_cleanup_chips(struct ingenic_nfc *nfc)
 {
-	struct jz4780_nand_chip *chip;
+	struct ingenic_nand *chip;
 
 	while (!list_empty(&nfc->chips)) {
-		chip = list_first_entry(&nfc->chips, struct jz4780_nand_chip, chip_list);
+		chip = list_first_entry(&nfc->chips,
+					struct ingenic_nand, chip_list);
 		nand_release(&chip->chip);
 		list_del(&chip->chip_list);
 	}
 }
 
-static int jz4780_nand_init_chips(struct jz4780_nand_controller *nfc,
-				  struct platform_device *pdev)
+static int ingenic_nand_init_chips(struct ingenic_nfc *nfc,
+				   struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np;
@@ -319,14 +318,15 @@ static int jz4780_nand_init_chips(struct jz4780_nand_controller *nfc,
 	int num_chips = of_get_child_count(dev->of_node);
 
 	if (num_chips > nfc->num_banks) {
-		dev_err(dev, "found %d chips but only %d banks\n", num_chips, nfc->num_banks);
+		dev_err(dev, "found %d chips but only %d banks\n",
+			num_chips, nfc->num_banks);
 		return -EINVAL;
 	}
 
 	for_each_child_of_node(dev->of_node, np) {
-		ret = jz4780_nand_init_chip(pdev, nfc, np, i);
+		ret = ingenic_nand_init_chip(pdev, nfc, np, i);
 		if (ret) {
-			jz4780_nand_cleanup_chips(nfc);
+			ingenic_nand_cleanup_chips(nfc);
 			return ret;
 		}
 
@@ -336,11 +336,11 @@ static int jz4780_nand_init_chips(struct jz4780_nand_controller *nfc,
 	return 0;
 }
 
-static int jz4780_nand_probe(struct platform_device *pdev)
+static int ingenic_nand_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	unsigned int num_banks;
-	struct jz4780_nand_controller *nfc;
+	struct ingenic_nfc *nfc;
 	int ret;
 
 	num_banks = jz4780_nemc_num_banks(dev);
@@ -367,7 +367,7 @@ static int jz4780_nand_probe(struct platform_device *pdev)
 	nand_controller_init(&nfc->controller);
 	INIT_LIST_HEAD(&nfc->chips);
 
-	ret = jz4780_nand_init_chips(nfc, pdev);
+	ret = ingenic_nand_init_chips(nfc, pdev);
 	if (ret) {
 		if (nfc->bch)
 			jz4780_bch_release(nfc->bch);
@@ -378,35 +378,35 @@ static int jz4780_nand_probe(struct platform_device *pdev)
 	return 0;
 }
 
-static int jz4780_nand_remove(struct platform_device *pdev)
+static int ingenic_nand_remove(struct platform_device *pdev)
 {
-	struct jz4780_nand_controller *nfc = platform_get_drvdata(pdev);
+	struct ingenic_nfc *nfc = platform_get_drvdata(pdev);
 
 	if (nfc->bch)
 		jz4780_bch_release(nfc->bch);
 
-	jz4780_nand_cleanup_chips(nfc);
+	ingenic_nand_cleanup_chips(nfc);
 
 	return 0;
 }
 
-static const struct of_device_id jz4780_nand_dt_match[] = {
+static const struct of_device_id ingenic_nand_dt_match[] = {
 	{ .compatible = "ingenic,jz4780-nand" },
 	{},
 };
-MODULE_DEVICE_TABLE(of, jz4780_nand_dt_match);
+MODULE_DEVICE_TABLE(of, ingenic_nand_dt_match);
 
-static struct platform_driver jz4780_nand_driver = {
-	.probe		= jz4780_nand_probe,
-	.remove		= jz4780_nand_remove,
+static struct platform_driver ingenic_nand_driver = {
+	.probe		= ingenic_nand_probe,
+	.remove		= ingenic_nand_remove,
 	.driver	= {
 		.name	= DRV_NAME,
-		.of_match_table = of_match_ptr(jz4780_nand_dt_match),
+		.of_match_table = of_match_ptr(ingenic_nand_dt_match),
 	},
 };
-module_platform_driver(jz4780_nand_driver);
+module_platform_driver(ingenic_nand_driver);
 
 MODULE_AUTHOR("Alex Smith <alex@alex-smith.me.uk>");
 MODULE_AUTHOR("Harvey Hunt <harveyhuntnexus@gmail.com>");
-MODULE_DESCRIPTION("Ingenic JZ4780 NAND driver");
+MODULE_DESCRIPTION("Ingenic JZ47xx NAND driver");
 MODULE_LICENSE("GPL v2");
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 6/9] mtd: rawnand: ingenic: Separate top-level and SoC specific code

[Paul Cercueil]

The ingenic-nand driver uses an API provided by the jz4780-bch driver.
This makes it difficult to support other SoCs in the jz4780-bch driver.
To work around this, we separate the API functions from the SoC-specific
code, so that these API functions are SoC-agnostic.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

v2: Add an optional .probe() callback. It is used for instance to set
    the clock rate in the JZ4780 backend.

v3: The common code is now inside the ingenic-ecc module. Each
    SoC-specific ECC code is now in its own module, which leaves to the
    user the choice of which (if any) ECC code should be supported.

v4: No change

 drivers/mtd/nand/raw/ingenic/Kconfig        |  17 +++
 drivers/mtd/nand/raw/ingenic/Makefile       |   5 +-
 drivers/mtd/nand/raw/ingenic/ingenic_ecc.c  | 157 +++++++++++++++++++++++++
 drivers/mtd/nand/raw/ingenic/ingenic_ecc.h  |  84 ++++++++++++++
 drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  38 +++----
 drivers/mtd/nand/raw/ingenic/jz4780_bch.c   | 170 +++++-----------------------
 drivers/mtd/nand/raw/ingenic/jz4780_bch.h   |  40 -------
 7 files changed, 308 insertions(+), 203 deletions(-)
 create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
 create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
 delete mode 100644 drivers/mtd/nand/raw/ingenic/jz4780_bch.h

diff --git a/drivers/mtd/nand/raw/ingenic/Kconfig b/drivers/mtd/nand/raw/ingenic/Kconfig
index 67806c87b2c4..4bf7d7af3b0a 100644
--- a/drivers/mtd/nand/raw/ingenic/Kconfig
+++ b/drivers/mtd/nand/raw/ingenic/Kconfig
@@ -11,3 +11,20 @@ config MTD_NAND_JZ4780
 	help
 	  Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
 	  based boards, using the BCH controller for hardware error correction.
+
+if MTD_NAND_JZ4780
+
+config MTD_NAND_INGENIC_ECC
+	tristate
+
+config MTD_NAND_JZ4780_BCH
+	tristate "Hardware BCH support for JZ4780 SoC"
+	select MTD_NAND_INGENIC_ECC
+	help
+	  Enable this driver to support the BCH error-correction hardware
+	  present on the JZ4780 SoC from Ingenic.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called jz4780-bch.
+
+endif # MTD_NAND_JZ4780
diff --git a/drivers/mtd/nand/raw/ingenic/Makefile b/drivers/mtd/nand/raw/ingenic/Makefile
index af2d5de21f60..f3c3c0f230b0 100644
--- a/drivers/mtd/nand/raw/ingenic/Makefile
+++ b/drivers/mtd/nand/raw/ingenic/Makefile
@@ -1,2 +1,5 @@
 obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
-obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o jz4780_bch.o
+obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o
+
+obj-$(CONFIG_MTD_NAND_INGENIC_ECC) += ingenic_ecc.o
+obj-$(CONFIG_MTD_NAND_JZ4780_BCH) += jz4780_bch.o
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
new file mode 100644
index 000000000000..a5b2f31803ff
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * JZ47xx ECC common code
+ *
+ * Copyright (c) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/init.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include "ingenic_ecc.h"
+
+/**
+ * ingenic_ecc_calculate() - calculate ECC for a data buffer
+ * @ecc: ECC device.
+ * @params: ECC parameters.
+ * @buf: input buffer with raw data.
+ * @ecc_code: output buffer with ECC.
+ *
+ * Return: 0 on success, -ETIMEDOUT if timed out while waiting for ECC
+ * controller.
+ */
+int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
+			  struct ingenic_ecc_params *params,
+			  const u8 *buf, u8 *ecc_code)
+{
+	return ecc->ops->calculate(ecc, params, buf, ecc_code);
+}
+EXPORT_SYMBOL(ingenic_ecc_calculate);
+
+/**
+ * ingenic_ecc_correct() - detect and correct bit errors
+ * @ecc: ECC device.
+ * @params: ECC parameters.
+ * @buf: raw data read from the chip.
+ * @ecc_code: ECC read from the chip.
+ *
+ * Given the raw data and the ECC read from the NAND device, detects and
+ * corrects errors in the data.
+ *
+ * Return: the number of bit errors corrected, -EBADMSG if there are too many
+ * errors to correct or -ETIMEDOUT if we timed out waiting for the controller.
+ */
+int ingenic_ecc_correct(struct ingenic_ecc *ecc,
+			struct ingenic_ecc_params *params,
+			u8 *buf, u8 *ecc_code)
+{
+	return ecc->ops->correct(ecc, params, buf, ecc_code);
+}
+EXPORT_SYMBOL(ingenic_ecc_correct);
+
+/**
+ * ingenic_ecc_get() - get the ECC controller device
+ * @np: ECC device tree node.
+ *
+ * Gets the ECC controller device from the specified device tree node. The
+ * device must be released with ingenic_ecc_release() when it is no longer being
+ * used.
+ *
+ * Return: a pointer to ingenic_ecc, errors are encoded into the pointer.
+ * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
+ */
+static struct ingenic_ecc *ingenic_ecc_get(struct device_node *np)
+{
+	struct platform_device *pdev;
+	struct ingenic_ecc *ecc;
+
+	pdev = of_find_device_by_node(np);
+	if (!pdev || !platform_get_drvdata(pdev))
+		return ERR_PTR(-EPROBE_DEFER);
+
+	get_device(&pdev->dev);
+
+	ecc = platform_get_drvdata(pdev);
+	clk_prepare_enable(ecc->clk);
+
+	return ecc;
+}
+
+/**
+ * of_ingenic_ecc_get() - get the ECC controller from a DT node
+ * @of_node: the node that contains a bch-controller property.
+ *
+ * Get the bch-controller property from the given device tree
+ * node and pass it to ingenic_ecc_get to do the work.
+ *
+ * Return: a pointer to ingenic_ecc, errors are encoded into the pointer.
+ * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
+ */
+struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *of_node)
+{
+	struct ingenic_ecc *ecc = NULL;
+	struct device_node *np;
+
+	np = of_parse_phandle(of_node, "ingenic,bch-controller", 0);
+
+	if (np) {
+		ecc = ingenic_ecc_get(np);
+		of_node_put(np);
+	}
+	return ecc;
+}
+EXPORT_SYMBOL(of_ingenic_ecc_get);
+
+/**
+ * ingenic_ecc_release() - release the ECC controller device
+ * @ecc: ECC device.
+ */
+void ingenic_ecc_release(struct ingenic_ecc *ecc)
+{
+	clk_disable_unprepare(ecc->clk);
+	put_device(ecc->dev);
+}
+EXPORT_SYMBOL(ingenic_ecc_release);
+
+int ingenic_ecc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ingenic_ecc *ecc;
+	struct resource *res;
+	int ret = 0;
+
+	ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL);
+	if (!ecc)
+		return -ENOMEM;
+
+	ecc->ops = device_get_match_data(dev);
+	if (!ecc->ops)
+		return -EINVAL;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ecc->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(ecc->base))
+		return PTR_ERR(ecc->base);
+
+	ecc->ops->disable(ecc);
+
+	ecc->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(ecc->clk)) {
+		dev_err(dev, "failed to get clock: %ld\n", PTR_ERR(ecc->clk));
+		return PTR_ERR(ecc->clk);
+	}
+
+	mutex_init(&ecc->lock);
+
+	ecc->dev = dev;
+	platform_set_drvdata(pdev, ecc);
+
+	if (ecc->ops->probe)
+		ret = ecc->ops->probe(ecc);
+
+	return ret;
+}
+EXPORT_SYMBOL(ingenic_ecc_probe);
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
new file mode 100644
index 000000000000..6dfb19f54c9b
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
@@ -0,0 +1,84 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DRIVERS_MTD_NAND_INGENIC_ECC_INTERNAL_H__
+#define __DRIVERS_MTD_NAND_INGENIC_ECC_INTERNAL_H__
+
+#include <linux/compiler_types.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/types.h>
+#include <uapi/asm-generic/errno-base.h>
+
+struct clk;
+struct device;
+struct ingenic_ecc;
+struct platform_device;
+
+/**
+ * struct ingenic_ecc_params - ECC parameters
+ * @size: data bytes per ECC step.
+ * @bytes: ECC bytes per step.
+ * @strength: number of correctable bits per ECC step.
+ */
+struct ingenic_ecc_params {
+	int size;
+	int bytes;
+	int strength;
+};
+
+#ifdef CONFIG_MTD_NAND_INGENIC_ECC
+int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
+			  struct ingenic_ecc_params *params,
+			  const u8 *buf, u8 *ecc_code);
+int ingenic_ecc_correct(struct ingenic_ecc *ecc,
+			struct ingenic_ecc_params *params, u8 *buf,
+			u8 *ecc_code);
+
+void ingenic_ecc_release(struct ingenic_ecc *ecc);
+struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *np);
+#else /* CONFIG_MTD_NAND_INGENIC_ECC */
+int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
+			  struct ingenic_ecc_params *params,
+			  const u8 *buf, u8 *ecc_code)
+{
+	return -ENODEV;
+}
+
+int ingenic_ecc_correct(struct ingenic_ecc *ecc,
+			struct ingenic_ecc_params *params, u8 *buf,
+			u8 *ecc_code)
+{
+	return -ENODEV;
+}
+
+void ingenic_ecc_release(struct ingenic_ecc *ecc)
+{
+}
+
+struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *np)
+{
+	return ERR_PTR(-ENODEV);
+}
+#endif /* CONFIG_MTD_NAND_INGENIC_ECC */
+
+struct ingenic_ecc_ops {
+	int (*probe)(struct ingenic_ecc *ecc);
+	void (*disable)(struct ingenic_ecc *ecc);
+	int (*calculate)(struct ingenic_ecc *ecc,
+			 struct ingenic_ecc_params *params,
+			 const u8 *buf, u8 *ecc_code);
+	int (*correct)(struct ingenic_ecc *ecc,
+			struct ingenic_ecc_params *params,
+			u8 *buf, u8 *ecc_code);
+};
+
+struct ingenic_ecc {
+	struct device *dev;
+	const struct ingenic_ecc_ops *ops;
+	void __iomem *base;
+	struct clk *clk;
+	struct mutex lock;
+};
+
+int ingenic_ecc_probe(struct platform_device *pdev);
+
+#endif /* __DRIVERS_MTD_NAND_INGENIC_ECC_INTERNAL_H__ */
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
index 8c73f7c5be9a..0f51fd15fe79 100644
--- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
@@ -22,7 +22,7 @@
 
 #include <linux/jz4780-nemc.h>
 
-#include "jz4780_bch.h"
+#include "ingenic_ecc.h"
 
 #define DRV_NAME	"ingenic-nand"
 
@@ -40,7 +40,7 @@ struct ingenic_nand_cs {
 
 struct ingenic_nfc {
 	struct device *dev;
-	struct jz4780_bch *bch;
+	struct ingenic_ecc *ecc;
 	struct nand_controller controller;
 	unsigned int num_banks;
 	struct list_head chips;
@@ -124,10 +124,10 @@ static int ingenic_nand_ecc_calculate(struct nand_chip *chip, const u8 *dat,
 {
 	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
 	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
-	struct jz4780_bch_params params;
+	struct ingenic_ecc_params params;
 
 	/*
-	 * Don't need to generate the ECC when reading, BCH does it for us as
+	 * Don't need to generate the ECC when reading, ECC does it for us as
 	 * part of decoding/correction.
 	 */
 	if (nand->reading)
@@ -137,7 +137,7 @@ static int ingenic_nand_ecc_calculate(struct nand_chip *chip, const u8 *dat,
 	params.bytes = nand->chip.ecc.bytes;
 	params.strength = nand->chip.ecc.strength;
 
-	return jz4780_bch_calculate(nfc->bch, &params, dat, ecc_code);
+	return ingenic_ecc_calculate(nfc->ecc, &params, dat, ecc_code);
 }
 
 static int ingenic_nand_ecc_correct(struct nand_chip *chip, u8 *dat,
@@ -145,13 +145,13 @@ static int ingenic_nand_ecc_correct(struct nand_chip *chip, u8 *dat,
 {
 	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
 	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
-	struct jz4780_bch_params params;
+	struct ingenic_ecc_params params;
 
 	params.size = nand->chip.ecc.size;
 	params.bytes = nand->chip.ecc.bytes;
 	params.strength = nand->chip.ecc.strength;
 
-	return jz4780_bch_correct(nfc->bch, &params, dat, read_ecc);
+	return ingenic_ecc_correct(nfc->ecc, &params, dat, read_ecc);
 }
 
 static int ingenic_nand_attach_chip(struct nand_chip *chip)
@@ -165,8 +165,8 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
 
 	switch (chip->ecc.mode) {
 	case NAND_ECC_HW:
-		if (!nfc->bch) {
-			dev_err(nfc->dev, "HW BCH selected, but BCH controller not found\n");
+		if (!nfc->ecc) {
+			dev_err(nfc->dev, "HW ECC selected, but ECC controller not found\n");
 			return -ENODEV;
 		}
 
@@ -176,7 +176,7 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
 		/* fall through */
 	case NAND_ECC_SOFT:
 		dev_info(nfc->dev, "using %s (strength %d, size %d, bytes %d)\n",
-			 (nfc->bch) ? "hardware BCH" : "software ECC",
+			 (nfc->ecc) ? "hardware ECC" : "software ECC",
 			 chip->ecc.strength, chip->ecc.size, chip->ecc.bytes);
 		break;
 	case NAND_ECC_NONE:
@@ -354,12 +354,12 @@ static int ingenic_nand_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	/*
-	 * Check for BCH HW before we call nand_scan_ident, to prevent us from
-	 * having to call it again if the BCH driver returns -EPROBE_DEFER.
+	 * Check for ECC HW before we call nand_scan_ident, to prevent us from
+	 * having to call it again if the ECC driver returns -EPROBE_DEFER.
 	 */
-	nfc->bch = of_jz4780_bch_get(dev->of_node);
-	if (IS_ERR(nfc->bch))
-		return PTR_ERR(nfc->bch);
+	nfc->ecc = of_ingenic_ecc_get(dev->of_node);
+	if (IS_ERR(nfc->ecc))
+		return PTR_ERR(nfc->ecc);
 
 	nfc->dev = dev;
 	nfc->num_banks = num_banks;
@@ -369,8 +369,8 @@ static int ingenic_nand_probe(struct platform_device *pdev)
 
 	ret = ingenic_nand_init_chips(nfc, pdev);
 	if (ret) {
-		if (nfc->bch)
-			jz4780_bch_release(nfc->bch);
+		if (nfc->ecc)
+			ingenic_ecc_release(nfc->ecc);
 		return ret;
 	}
 
@@ -382,8 +382,8 @@ static int ingenic_nand_remove(struct platform_device *pdev)
 {
 	struct ingenic_nfc *nfc = platform_get_drvdata(pdev);
 
-	if (nfc->bch)
-		jz4780_bch_release(nfc->bch);
+	if (nfc->ecc)
+		ingenic_ecc_release(nfc->ecc);
 
 	ingenic_nand_cleanup_chips(nfc);
 
diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_bch.c b/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
index 7e4e5e627603..1e86a1037d62 100644
--- a/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
+++ b/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * JZ4780 BCH controller
+ * JZ4780 BCH controller driver
  *
  * Copyright (c) 2015 Imagination Technologies
  * Author: Alex Smith <alex.smith@imgtec.com>
@@ -8,18 +8,15 @@
 
 #include <linux/bitops.h>
 #include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/io.h>
 #include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
-#include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
 
-#include "jz4780_bch.h"
+#include "ingenic_ecc.h"
 
 #define BCH_BHCR			0x0
 #define BCH_BHCCR			0x8
@@ -62,15 +59,8 @@
 /* Timeout for BCH calculation/correction. */
 #define BCH_TIMEOUT_US			100000
 
-struct jz4780_bch {
-	struct device *dev;
-	void __iomem *base;
-	struct clk *clk;
-	struct mutex lock;
-};
-
-static void jz4780_bch_init(struct jz4780_bch *bch,
-			    struct jz4780_bch_params *params, bool encode)
+static void jz4780_bch_init(struct ingenic_ecc *bch,
+			    struct ingenic_ecc_params *params, bool encode)
 {
 	u32 reg;
 
@@ -90,13 +80,13 @@ static void jz4780_bch_init(struct jz4780_bch *bch,
 	writel(reg, bch->base + BCH_BHCR);
 }
 
-static void jz4780_bch_disable(struct jz4780_bch *bch)
+static void jz4780_bch_disable(struct ingenic_ecc *bch)
 {
 	writel(readl(bch->base + BCH_BHINT), bch->base + BCH_BHINT);
 	writel(BCH_BHCR_BCHE, bch->base + BCH_BHCCR);
 }
 
-static void jz4780_bch_write_data(struct jz4780_bch *bch, const void *buf,
+static void jz4780_bch_write_data(struct ingenic_ecc *bch, const void *buf,
 				  size_t size)
 {
 	size_t size32 = size / sizeof(u32);
@@ -113,7 +103,7 @@ static void jz4780_bch_write_data(struct jz4780_bch *bch, const void *buf,
 		writeb(*src8++, bch->base + BCH_BHDR);
 }
 
-static void jz4780_bch_read_parity(struct jz4780_bch *bch, void *buf,
+static void jz4780_bch_read_parity(struct ingenic_ecc *bch, void *buf,
 				   size_t size)
 {
 	size_t size32 = size / sizeof(u32);
@@ -143,7 +133,7 @@ static void jz4780_bch_read_parity(struct jz4780_bch *bch, void *buf,
 	}
 }
 
-static bool jz4780_bch_wait_complete(struct jz4780_bch *bch, unsigned int irq,
+static bool jz4780_bch_wait_complete(struct ingenic_ecc *bch, unsigned int irq,
 				     u32 *status)
 {
 	u32 reg;
@@ -167,18 +157,9 @@ static bool jz4780_bch_wait_complete(struct jz4780_bch *bch, unsigned int irq,
 	return true;
 }
 
-/**
- * jz4780_bch_calculate() - calculate ECC for a data buffer
- * @bch: BCH device.
- * @params: BCH parameters.
- * @buf: input buffer with raw data.
- * @ecc_code: output buffer with ECC.
- *
- * Return: 0 on success, -ETIMEDOUT if timed out while waiting for BCH
- * controller.
- */
-int jz4780_bch_calculate(struct jz4780_bch *bch, struct jz4780_bch_params *params,
-			 const u8 *buf, u8 *ecc_code)
+static int jz4780_calculate(struct ingenic_ecc *bch,
+			    struct ingenic_ecc_params *params,
+			    const u8 *buf, u8 *ecc_code)
 {
 	int ret = 0;
 
@@ -197,23 +178,10 @@ int jz4780_bch_calculate(struct jz4780_bch *bch, struct jz4780_bch_params *param
 	mutex_unlock(&bch->lock);
 	return ret;
 }
-EXPORT_SYMBOL(jz4780_bch_calculate);
-
-/**
- * jz4780_bch_correct() - detect and correct bit errors
- * @bch: BCH device.
- * @params: BCH parameters.
- * @buf: raw data read from the chip.
- * @ecc_code: ECC read from the chip.
- *
- * Given the raw data and the ECC read from the NAND device, detects and
- * corrects errors in the data.
- *
- * Return: the number of bit errors corrected, -EBADMSG if there are too many
- * errors to correct or -ETIMEDOUT if we timed out waiting for the controller.
- */
-int jz4780_bch_correct(struct jz4780_bch *bch, struct jz4780_bch_params *params,
-		       u8 *buf, u8 *ecc_code)
+
+static int jz4780_correct(struct ingenic_ecc *bch,
+			  struct ingenic_ecc_params *params,
+			  u8 *buf, u8 *ecc_code)
 {
 	u32 reg, mask, index;
 	int i, ret, count;
@@ -259,113 +227,29 @@ int jz4780_bch_correct(struct jz4780_bch *bch, struct jz4780_bch_params *params,
 	mutex_unlock(&bch->lock);
 	return ret;
 }
-EXPORT_SYMBOL(jz4780_bch_correct);
-
-/**
- * jz4780_bch_get() - get the BCH controller device
- * @np: BCH device tree node.
- *
- * Gets the BCH controller device from the specified device tree node. The
- * device must be released with jz4780_bch_release() when it is no longer being
- * used.
- *
- * Return: a pointer to jz4780_bch, errors are encoded into the pointer.
- * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
- */
-static struct jz4780_bch *jz4780_bch_get(struct device_node *np)
-{
-	struct platform_device *pdev;
-	struct jz4780_bch *bch;
-
-	pdev = of_find_device_by_node(np);
-	if (!pdev || !platform_get_drvdata(pdev))
-		return ERR_PTR(-EPROBE_DEFER);
-
-	get_device(&pdev->dev);
-
-	bch = platform_get_drvdata(pdev);
-	clk_prepare_enable(bch->clk);
-
-	return bch;
-}
-
-/**
- * of_jz4780_bch_get() - get the BCH controller from a DT node
- * @of_node: the node that contains a bch-controller property.
- *
- * Get the bch-controller property from the given device tree
- * node and pass it to jz4780_bch_get to do the work.
- *
- * Return: a pointer to jz4780_bch, errors are encoded into the pointer.
- * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
- */
-struct jz4780_bch *of_jz4780_bch_get(struct device_node *of_node)
-{
-	struct jz4780_bch *bch = NULL;
-	struct device_node *np;
-
-	np = of_parse_phandle(of_node, "ingenic,bch-controller", 0);
-
-	if (np) {
-		bch = jz4780_bch_get(np);
-		of_node_put(np);
-	}
-	return bch;
-}
-EXPORT_SYMBOL(of_jz4780_bch_get);
 
-/**
- * jz4780_bch_release() - release the BCH controller device
- * @bch: BCH device.
- */
-void jz4780_bch_release(struct jz4780_bch *bch)
+static int jz4780_bch_probe(struct ingenic_ecc *bch)
 {
-	clk_disable_unprepare(bch->clk);
-	put_device(bch->dev);
-}
-EXPORT_SYMBOL(jz4780_bch_release);
-
-static int jz4780_bch_probe(struct platform_device *pdev)
-{
-	struct device *dev = &pdev->dev;
-	struct jz4780_bch *bch;
-	struct resource *res;
-
-	bch = devm_kzalloc(dev, sizeof(*bch), GFP_KERNEL);
-	if (!bch)
-		return -ENOMEM;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	bch->base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(bch->base))
-		return PTR_ERR(bch->base);
-
-	jz4780_bch_disable(bch);
-
-	bch->clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(bch->clk)) {
-		dev_err(dev, "failed to get clock: %ld\n", PTR_ERR(bch->clk));
-		return PTR_ERR(bch->clk);
-	}
-
 	clk_set_rate(bch->clk, BCH_CLK_RATE);
 
-	mutex_init(&bch->lock);
-
-	bch->dev = dev;
-	platform_set_drvdata(pdev, bch);
-
 	return 0;
 }
 
+static const struct ingenic_ecc_ops jz4780_bch_ops = {
+	.probe = jz4780_bch_probe,
+	.disable = jz4780_bch_disable,
+	.calculate = jz4780_calculate,
+	.correct = jz4780_correct,
+};
+
 static const struct of_device_id jz4780_bch_dt_match[] = {
-	{ .compatible = "ingenic,jz4780-bch" },
+	{ .compatible = "ingenic,jz4780-bch", .data = &jz4780_bch_ops },
 	{},
 };
 MODULE_DEVICE_TABLE(of, jz4780_bch_dt_match);
 
 static struct platform_driver jz4780_bch_driver = {
-	.probe		= jz4780_bch_probe,
+	.probe		= ingenic_ecc_probe,
 	.driver	= {
 		.name	= "jz4780-bch",
 		.of_match_table = of_match_ptr(jz4780_bch_dt_match),
diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_bch.h b/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
deleted file mode 100644
index 451e0c770160..000000000000
--- a/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
+++ /dev/null
@@ -1,40 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * JZ4780 BCH controller
- *
- * Copyright (c) 2015 Imagination Technologies
- * Author: Alex Smith <alex.smith@imgtec.com>
- */
-
-#ifndef __DRIVERS_MTD_NAND_JZ4780_BCH_H__
-#define __DRIVERS_MTD_NAND_JZ4780_BCH_H__
-
-#include <linux/types.h>
-
-struct device;
-struct device_node;
-struct jz4780_bch;
-
-/**
- * struct jz4780_bch_params - BCH parameters
- * @size: data bytes per ECC step.
- * @bytes: ECC bytes per step.
- * @strength: number of correctable bits per ECC step.
- */
-struct jz4780_bch_params {
-	int size;
-	int bytes;
-	int strength;
-};
-
-int jz4780_bch_calculate(struct jz4780_bch *bch,
-				struct jz4780_bch_params *params,
-				const u8 *buf, u8 *ecc_code);
-int jz4780_bch_correct(struct jz4780_bch *bch,
-			      struct jz4780_bch_params *params, u8 *buf,
-			      u8 *ecc_code);
-
-void jz4780_bch_release(struct jz4780_bch *bch);
-struct jz4780_bch *of_jz4780_bch_get(struct device_node *np);
-
-#endif /* __DRIVERS_MTD_NAND_JZ4780_BCH_H__ */
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 6/9] mtd: rawnand: ingenic: Separate top-level and SoC specific code

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Sat,  9 Feb 2019 16:23:02
-0300:

> The ingenic-nand driver uses an API provided by the jz4780-bch driver.
> This makes it difficult to support other SoCs in the jz4780-bch driver.
> To work around this, we separate the API functions from the SoC-specific
> code, so that these API functions are SoC-agnostic.
> 

I like the idea, actually I am working on this separation (see
[1]) and I would really appreciate that you try to implement the
interface when it will be available (v2 is coming this week, I think v3
will be the one to test when raw NAND devices will be properly
supported). I will add you in Cc: if you want to follow/review.

[1] http://lists.infradead.org/pipermail/linux-mtd/2019-February/087815.html

> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> v2: Add an optional .probe() callback. It is used for instance to set
>     the clock rate in the JZ4780 backend.
> 
> v3: The common code is now inside the ingenic-ecc module. Each
>     SoC-specific ECC code is now in its own module, which leaves to the
>     user the choice of which (if any) ECC code should be supported.
> 
> v4: No change
> 
>  drivers/mtd/nand/raw/ingenic/Kconfig        |  17 +++
>  drivers/mtd/nand/raw/ingenic/Makefile       |   5 +-
>  drivers/mtd/nand/raw/ingenic/ingenic_ecc.c  | 157 +++++++++++++++++++++++++
>  drivers/mtd/nand/raw/ingenic/ingenic_ecc.h  |  84 ++++++++++++++
>  drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  38 +++----
>  drivers/mtd/nand/raw/ingenic/jz4780_bch.c   | 170 +++++-----------------------
>  drivers/mtd/nand/raw/ingenic/jz4780_bch.h   |  40 -------
>  7 files changed, 308 insertions(+), 203 deletions(-)
>  create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
>  create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
>  delete mode 100644 drivers/mtd/nand/raw/ingenic/jz4780_bch.h
> 

[...]

> diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
> index 8c73f7c5be9a..0f51fd15fe79 100644
> --- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
> +++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
> @@ -22,7 +22,7 @@
>  
>  #include <linux/jz4780-nemc.h>
>  
> -#include "jz4780_bch.h"
> +#include "ingenic_ecc.h"
>  
>  #define DRV_NAME	"ingenic-nand"
>  
> @@ -40,7 +40,7 @@ struct ingenic_nand_cs {
>  
>  struct ingenic_nfc {
>  	struct device *dev;
> -	struct jz4780_bch *bch;
> +	struct ingenic_ecc *ecc;
>  	struct nand_controller controller;
>  	unsigned int num_banks;
>  	struct list_head chips;
> @@ -124,10 +124,10 @@ static int ingenic_nand_ecc_calculate(struct nand_chip *chip, const u8 *dat,
>  {
>  	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
>  	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
> -	struct jz4780_bch_params params;
> +	struct ingenic_ecc_params params;
>  
>  	/*
> -	 * Don't need to generate the ECC when reading, BCH does it for us as
> +	 * Don't need to generate the ECC when reading, ECC does it for us as

"the ECC engine does it for us" would be more meaningful.

>  	 * part of decoding/correction.
>  	 */
>  	if (nand->reading)
> @@ -137,7 +137,7 @@ static int ingenic_nand_ecc_calculate(struct nand_chip *chip, const u8 *dat,
>  	params.bytes = nand->chip.ecc.bytes;
>  	params.strength = nand->chip.ecc.strength;
>  
> -	return jz4780_bch_calculate(nfc->bch, &params, dat, ecc_code);
> +	return ingenic_ecc_calculate(nfc->ecc, &params, dat, ecc_code);
>  }
>  

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 6/9] mtd: rawnand: ingenic: Separate top-level and SoC specific code

[Paul Cercueil]

On Mon, Mar 4, 2019 at 11:20 AM, Miquel Raynal 
<miquel.raynal@bootlin.com> wrote:
> Hi Paul,
> 
> Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> 
> wrote on Sat,  9 Feb 2019 16:23:02
> -0300:
> 
>>  The ingenic-nand driver uses an API provided by the jz4780-bch 
>> driver.
>>  This makes it difficult to support other SoCs in the jz4780-bch 
>> driver.
>>  To work around this, we separate the API functions from the 
>> SoC-specific
>>  code, so that these API functions are SoC-agnostic.
>> 
> 
> I like the idea, actually I am working on this separation (see
> [1]) and I would really appreciate that you try to implement the
> interface when it will be available (v2 is coming this week, I think 
> v3
> will be the one to test when raw NAND devices will be properly
> supported). I will add you in Cc: if you want to follow/review.
> 
> [1] 
> <http://lists.infradead.org/pipermail/linux-mtd/2019-February/087815.html>

Do you think this will be ready for 5.2?

You can add me in Cc:.

>>  Signed-off-by: Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>>
>>  ---
>> 
>>  v2: Add an optional .probe() callback. It is used for instance to 
>> set
>>      the clock rate in the JZ4780 backend.
>> 
>>  v3: The common code is now inside the ingenic-ecc module. Each
>>      SoC-specific ECC code is now in its own module, which leaves to 
>> the
>>      user the choice of which (if any) ECC code should be supported.
>> 
>>  v4: No change
>> 
>>   drivers/mtd/nand/raw/ingenic/Kconfig        |  17 +++
>>   drivers/mtd/nand/raw/ingenic/Makefile       |   5 +-
>>   drivers/mtd/nand/raw/ingenic/ingenic_ecc.c  | 157 
>> +++++++++++++++++++++++++
>>   drivers/mtd/nand/raw/ingenic/ingenic_ecc.h  |  84 ++++++++++++++
>>   drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  38 +++----
>>   drivers/mtd/nand/raw/ingenic/jz4780_bch.c   | 170 
>> +++++-----------------------
>>   drivers/mtd/nand/raw/ingenic/jz4780_bch.h   |  40 -------
>>   7 files changed, 308 insertions(+), 203 deletions(-)
>>   create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
>>   create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
>>   delete mode 100644 drivers/mtd/nand/raw/ingenic/jz4780_bch.h
>> 
> 
> [...]
> 
>>  diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c 
>> b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
>>  index 8c73f7c5be9a..0f51fd15fe79 100644
>>  --- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
>>  +++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
>>  @@ -22,7 +22,7 @@
>> 
>>   #include <linux/jz4780-nemc.h>
>> 
>>  -#include "jz4780_bch.h"
>>  +#include "ingenic_ecc.h"
>> 
>>   #define DRV_NAME	"ingenic-nand"
>> 
>>  @@ -40,7 +40,7 @@ struct ingenic_nand_cs {
>> 
>>   struct ingenic_nfc {
>>   	struct device *dev;
>>  -	struct jz4780_bch *bch;
>>  +	struct ingenic_ecc *ecc;
>>   	struct nand_controller controller;
>>   	unsigned int num_banks;
>>   	struct list_head chips;
>>  @@ -124,10 +124,10 @@ static int ingenic_nand_ecc_calculate(struct 
>> nand_chip *chip, const u8 *dat,
>>   {
>>   	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
>>   	struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
>>  -	struct jz4780_bch_params params;
>>  +	struct ingenic_ecc_params params;
>> 
>>   	/*
>>  -	 * Don't need to generate the ECC when reading, BCH does it for 
>> us as
>>  +	 * Don't need to generate the ECC when reading, ECC does it for 
>> us as
> 
> "the ECC engine does it for us" would be more meaningful.

OK.

>>   	 * part of decoding/correction.
>>   	 */
>>   	if (nand->reading)
>>  @@ -137,7 +137,7 @@ static int ingenic_nand_ecc_calculate(struct 
>> nand_chip *chip, const u8 *dat,
>>   	params.bytes = nand->chip.ecc.bytes;
>>   	params.strength = nand->chip.ecc.strength;
>> 
>>  -	return jz4780_bch_calculate(nfc->bch, &params, dat, ecc_code);
>>  +	return ingenic_ecc_calculate(nfc->ecc, &params, dat, ecc_code);
>>   }
>> 
> 
> Thanks,
> Miquèl



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 6/9] mtd: rawnand: ingenic: Separate top-level and SoC specific code

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Mon, 04 Mar 2019 19:26:08
+0100:

> On Mon, Mar 4, 2019 at 11:20 AM, Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> > Hi Paul,
> > 
> > Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> > wrote on Sat,  9 Feb 2019 16:23:02
> > -0300:
> >   
> >>  The ingenic-nand driver uses an API provided by the jz4780-bch >> driver.
> >>  This makes it difficult to support other SoCs in the jz4780-bch >> driver.
> >>  To work around this, we separate the API functions from the >> SoC-specific
> >>  code, so that these API functions are SoC-agnostic.  
> >> >   
> > I like the idea, actually I am working on this separation (see
> > [1]) and I would really appreciate that you try to implement the
> > interface when it will be available (v2 is coming this week, I think > v3
> > will be the one to test when raw NAND devices will be properly
> > supported). I will add you in Cc: if you want to follow/review.
> > 
> > [1] > <http://lists.infradead.org/pipermail/linux-mtd/2019-February/087815.html
> >  
> 
> Do you think this will be ready for 5.2?

Maybe, but I can't tell for sure. It will depend on how invasive the
raw NAND conversion is. I don't want to delay your work but maybe once
the interface will be ready to be implemented it would be a great
opportunity to do it with the Ingenic driver.

> 
> You can add me in Cc:.

Thanks!
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 7/9] mtd: rawnand: ingenic: Add support for the JZ4740

[Paul Cercueil]

Add support for probing the ingenic-nand driver on the JZ4740 SoC from
Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
ECC hardware.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

Changes:

v2: New patch

v3: Also add support for the hardware ECC of the JZ4740 in this patch

v4: - Fix formatting issues
    - Add MODULE_* macros

 drivers/mtd/nand/raw/ingenic/Kconfig        |  10 ++
 drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
 drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 +++++--
 drivers/mtd/nand/raw/ingenic/jz4740_ecc.c   | 196 ++++++++++++++++++++++++++++
 4 files changed, 244 insertions(+), 11 deletions(-)
 create mode 100644 drivers/mtd/nand/raw/ingenic/jz4740_ecc.c

diff --git a/drivers/mtd/nand/raw/ingenic/Kconfig b/drivers/mtd/nand/raw/ingenic/Kconfig
index 4bf7d7af3b0a..cc663cc15119 100644
--- a/drivers/mtd/nand/raw/ingenic/Kconfig
+++ b/drivers/mtd/nand/raw/ingenic/Kconfig
@@ -17,6 +17,16 @@ if MTD_NAND_JZ4780
 config MTD_NAND_INGENIC_ECC
 	tristate
 
+config MTD_NAND_JZ4740_ECC
+	tristate "Hardware BCH support for JZ4740 SoC"
+	select MTD_NAND_INGENIC_ECC
+	help
+	  Enable this driver to support the Reed-Solomon error-correction
+	  hardware present on the JZ4740 SoC from Ingenic.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called jz4740-ecc.
+
 config MTD_NAND_JZ4780_BCH
 	tristate "Hardware BCH support for JZ4780 SoC"
 	select MTD_NAND_INGENIC_ECC
diff --git a/drivers/mtd/nand/raw/ingenic/Makefile b/drivers/mtd/nand/raw/ingenic/Makefile
index f3c3c0f230b0..563b7effcf59 100644
--- a/drivers/mtd/nand/raw/ingenic/Makefile
+++ b/drivers/mtd/nand/raw/ingenic/Makefile
@@ -2,4 +2,5 @@ obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
 obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o
 
 obj-$(CONFIG_MTD_NAND_INGENIC_ECC) += ingenic_ecc.o
+obj-$(CONFIG_MTD_NAND_JZ4740_ECC) += jz4740_ecc.o
 obj-$(CONFIG_MTD_NAND_JZ4780_BCH) += jz4780_bch.o
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
index 0f51fd15fe79..036938fdad51 100644
--- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/gpio/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
@@ -26,13 +27,15 @@
 
 #define DRV_NAME	"ingenic-nand"
 
-#define OFFSET_DATA	0x00000000
-#define OFFSET_CMD	0x00400000
-#define OFFSET_ADDR	0x00800000
-
 /* Command delay when there is no R/B pin. */
 #define RB_DELAY_US	100
 
+struct jz_soc_info {
+	unsigned long data_offset;
+	unsigned long addr_offset;
+	unsigned long cmd_offset;
+};
+
 struct ingenic_nand_cs {
 	unsigned int bank;
 	void __iomem *base;
@@ -41,6 +44,7 @@ struct ingenic_nand_cs {
 struct ingenic_nfc {
 	struct device *dev;
 	struct ingenic_ecc *ecc;
+	const struct jz_soc_info *soc_info;
 	struct nand_controller controller;
 	unsigned int num_banks;
 	struct list_head chips;
@@ -100,9 +104,9 @@ static void ingenic_nand_cmd_ctrl(struct nand_chip *chip, int cmd,
 		return;
 
 	if (ctrl & NAND_ALE)
-		writeb(cmd, cs->base + OFFSET_ADDR);
+		writeb(cmd, cs->base + nfc->soc_info->addr_offset);
 	else if (ctrl & NAND_CLE)
-		writeb(cmd, cs->base + OFFSET_CMD);
+		writeb(cmd, cs->base + nfc->soc_info->cmd_offset);
 }
 
 static int ingenic_nand_dev_ready(struct nand_chip *chip)
@@ -160,8 +164,13 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
 	struct ingenic_nfc *nfc = to_ingenic_nfc(chip->controller);
 	int eccbytes;
 
-	chip->ecc.bytes = fls((1 + 8) * chip->ecc.size)	*
-				(chip->ecc.strength / 8);
+	if (chip->ecc.strength == 4) {
+		/* JZ4740 uses 9 bytes of ECC to correct maximum 4 errors */
+		chip->ecc.bytes = 9;
+	} else {
+		chip->ecc.bytes = fls((1 + 8) * chip->ecc.size)	*
+				  (chip->ecc.strength / 8);
+	}
 
 	switch (chip->ecc.mode) {
 	case NAND_ECC_HW:
@@ -270,8 +279,8 @@ static int ingenic_nand_init_chip(struct platform_device *pdev,
 		return -ENOMEM;
 	mtd->dev.parent = dev;
 
-	chip->legacy.IO_ADDR_R = cs->base + OFFSET_DATA;
-	chip->legacy.IO_ADDR_W = cs->base + OFFSET_DATA;
+	chip->legacy.IO_ADDR_R = cs->base + nfc->soc_info->data_offset;
+	chip->legacy.IO_ADDR_W = cs->base + nfc->soc_info->data_offset;
 	chip->legacy.chip_delay = RB_DELAY_US;
 	chip->options = NAND_NO_SUBPAGE_WRITE;
 	chip->legacy.select_chip = ingenic_nand_select_chip;
@@ -353,6 +362,10 @@ static int ingenic_nand_probe(struct platform_device *pdev)
 	if (!nfc)
 		return -ENOMEM;
 
+	nfc->soc_info = device_get_match_data(dev);
+	if (!nfc->soc_info)
+		return -EINVAL;
+
 	/*
 	 * Check for ECC HW before we call nand_scan_ident, to prevent us from
 	 * having to call it again if the ECC driver returns -EPROBE_DEFER.
@@ -390,8 +403,21 @@ static int ingenic_nand_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct jz_soc_info jz4740_soc_info = {
+	.data_offset = 0x00000000,
+	.cmd_offset = 0x00008000,
+	.addr_offset = 0x00010000,
+};
+
+static const struct jz_soc_info jz4780_soc_info = {
+	.data_offset = 0x00000000,
+	.cmd_offset = 0x00400000,
+	.addr_offset = 0x00800000,
+};
+
 static const struct of_device_id ingenic_nand_dt_match[] = {
-	{ .compatible = "ingenic,jz4780-nand" },
+	{ .compatible = "ingenic,jz4740-nand", .data = &jz4740_soc_info },
+	{ .compatible = "ingenic,jz4780-nand", .data = &jz4780_soc_info },
 	{},
 };
 MODULE_DEVICE_TABLE(of, ingenic_nand_dt_match);
diff --git a/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
new file mode 100644
index 000000000000..83b42881720e
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * JZ4740 ECC controller driver
+ *
+ * Copyright (c) 2019 Paul Cercueil <paul@crapouillou.net>
+ *
+ * based on jz4740-nand.c
+ */
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include "ingenic_ecc.h"
+
+#define JZ_REG_NAND_ECC_CTRL	0x00
+#define JZ_REG_NAND_DATA	0x04
+#define JZ_REG_NAND_PAR0	0x08
+#define JZ_REG_NAND_PAR1	0x0C
+#define JZ_REG_NAND_PAR2	0x10
+#define JZ_REG_NAND_IRQ_STAT	0x14
+#define JZ_REG_NAND_IRQ_CTRL	0x18
+#define JZ_REG_NAND_ERR(x)	(0x1C + ((x) << 2))
+
+#define JZ_NAND_ECC_CTRL_PAR_READY	BIT(4)
+#define JZ_NAND_ECC_CTRL_ENCODING	BIT(3)
+#define JZ_NAND_ECC_CTRL_RS		BIT(2)
+#define JZ_NAND_ECC_CTRL_RESET		BIT(1)
+#define JZ_NAND_ECC_CTRL_ENABLE		BIT(0)
+
+#define JZ_NAND_STATUS_ERR_COUNT	(BIT(31) | BIT(30) | BIT(29))
+#define JZ_NAND_STATUS_PAD_FINISH	BIT(4)
+#define JZ_NAND_STATUS_DEC_FINISH	BIT(3)
+#define JZ_NAND_STATUS_ENC_FINISH	BIT(2)
+#define JZ_NAND_STATUS_UNCOR_ERROR	BIT(1)
+#define JZ_NAND_STATUS_ERROR		BIT(0)
+
+static const uint8_t empty_block_ecc[] = {
+	0xcd, 0x9d, 0x90, 0x58, 0xf4, 0x8b, 0xff, 0xb7, 0x6f
+};
+
+static void jz4740_ecc_init(struct ingenic_ecc *ecc, bool encode)
+{
+	uint32_t reg;
+
+	/* Clear interrupt status */
+	writel(0, ecc->base + JZ_REG_NAND_IRQ_STAT);
+
+	/* Initialize and enable ECC hardware */
+	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
+	reg |= JZ_NAND_ECC_CTRL_RESET;
+	reg |= JZ_NAND_ECC_CTRL_ENABLE;
+	reg |= JZ_NAND_ECC_CTRL_RS;
+	if (encode)
+		reg |= JZ_NAND_ECC_CTRL_ENCODING;
+	else
+		reg &= ~JZ_NAND_ECC_CTRL_ENCODING;
+
+	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
+}
+
+static int jz4740_ecc_calculate(struct ingenic_ecc *ecc,
+				struct ingenic_ecc_params *params,
+				const u8 *buf, u8 *ecc_code)
+{
+	uint32_t reg, status;
+	unsigned int timeout = 1000;
+	int i;
+
+	jz4740_ecc_init(ecc, true);
+
+	do {
+		status = readl(ecc->base + JZ_REG_NAND_IRQ_STAT);
+	} while (!(status & JZ_NAND_STATUS_ENC_FINISH) && --timeout);
+
+	if (timeout == 0)
+		return -ETIMEDOUT;
+
+	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
+	reg &= ~JZ_NAND_ECC_CTRL_ENABLE;
+	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
+
+	for (i = 0; i < params->bytes; ++i)
+		ecc_code[i] = readb(ecc->base + JZ_REG_NAND_PAR0 + i);
+
+	/* If the written data is completely 0xff, we also want to write 0xff as
+	 * ecc, otherwise we will get in trouble when doing subpage writes.
+	 */
+	if (memcmp(ecc_code, empty_block_ecc, ARRAY_SIZE(empty_block_ecc)) == 0)
+		memset(ecc_code, 0xff, ARRAY_SIZE(empty_block_ecc));
+
+	return 0;
+}
+
+static void jz_nand_correct_data(uint8_t *buf, int index, int mask)
+{
+	int offset = index & 0x7;
+	uint16_t data;
+
+	index += (index >> 3);
+
+	data = buf[index];
+	data |= buf[index + 1] << 8;
+
+	mask ^= (data >> offset) & 0x1ff;
+	data &= ~(0x1ff << offset);
+	data |= (mask << offset);
+
+	buf[index] = data & 0xff;
+	buf[index + 1] = (data >> 8) & 0xff;
+}
+
+static int jz4740_ecc_correct(struct ingenic_ecc *ecc,
+			      struct ingenic_ecc_params *params,
+			      u8 *buf, u8 *ecc_code)
+{
+	int i, error_count, index;
+	uint32_t reg, status, error;
+	unsigned int timeout = 1000;
+
+	jz4740_ecc_init(ecc, false);
+
+	for (i = 0; i < params->bytes; ++i)
+		writeb(ecc_code[i], ecc->base + JZ_REG_NAND_PAR0 + i);
+
+	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
+	reg |= JZ_NAND_ECC_CTRL_PAR_READY;
+	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
+
+	do {
+		status = readl(ecc->base + JZ_REG_NAND_IRQ_STAT);
+	} while (!(status & JZ_NAND_STATUS_DEC_FINISH) && --timeout);
+
+	if (timeout == 0)
+		return -ETIMEDOUT;
+
+	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
+	reg &= ~JZ_NAND_ECC_CTRL_ENABLE;
+	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
+
+	if (status & JZ_NAND_STATUS_ERROR) {
+		if (status & JZ_NAND_STATUS_UNCOR_ERROR)
+			return -EBADMSG;
+
+		error_count = (status & JZ_NAND_STATUS_ERR_COUNT) >> 29;
+
+		for (i = 0; i < error_count; ++i) {
+			error = readl(ecc->base + JZ_REG_NAND_ERR(i));
+			index = ((error >> 16) & 0x1ff) - 1;
+			if (index >= 0 && index < params->size)
+				jz_nand_correct_data(buf, index, error & 0x1ff);
+		}
+
+		return error_count;
+	}
+
+	return 0;
+}
+
+static void jz4740_ecc_disable(struct ingenic_ecc *ecc)
+{
+	u32 reg;
+
+	writel(0, ecc->base + JZ_REG_NAND_IRQ_STAT);
+	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
+	reg &= ~JZ_NAND_ECC_CTRL_ENABLE;
+	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
+}
+
+static const struct ingenic_ecc_ops jz4740_ecc_ops = {
+	.disable = jz4740_ecc_disable,
+	.calculate = jz4740_ecc_calculate,
+	.correct = jz4740_ecc_correct,
+};
+
+static const struct of_device_id jz4740_ecc_dt_match[] = {
+	{ .compatible = "ingenic,jz4740-ecc", .data = &jz4740_ecc_ops },
+	{},
+};
+MODULE_DEVICE_TABLE(of, jz4740_ecc_dt_match);
+
+static struct platform_driver jz4740_ecc_driver = {
+	.probe		= ingenic_ecc_probe,
+	.driver	= {
+		.name	= "jz4740-ecc",
+		.of_match_table = jz4740_ecc_dt_match,
+	},
+};
+module_platform_driver(jz4740_ecc_driver);
+
+MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
+MODULE_DESCRIPTION("Ingenic JZ4740 ECC controller driver");
+MODULE_LICENSE("GPL v2");
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 7/9] mtd: rawnand: ingenic: Add support for the JZ4740

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Sat,  9 Feb 2019 16:23:03
-0300:

> Add support for probing the ingenic-nand driver on the JZ4740 SoC from
> Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
> ECC hardware.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> Changes:
> 
> v2: New patch
> 
> v3: Also add support for the hardware ECC of the JZ4740 in this patch
> 
> v4: - Fix formatting issues
>     - Add MODULE_* macros
> 
>  drivers/mtd/nand/raw/ingenic/Kconfig        |  10 ++
>  drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
>  drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 +++++--
>  drivers/mtd/nand/raw/ingenic/jz4740_ecc.c   | 196 ++++++++++++++++++++++++++++
>  4 files changed, 244 insertions(+), 11 deletions(-)
>  create mode 100644 drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
> 

[...]

>  	switch (chip->ecc.mode) {
>  	case NAND_ECC_HW:
> @@ -270,8 +279,8 @@ static int ingenic_nand_init_chip(struct platform_device *pdev,
>  		return -ENOMEM;
>  	mtd->dev.parent = dev;
>  
> -	chip->legacy.IO_ADDR_R = cs->base + OFFSET_DATA;
> -	chip->legacy.IO_ADDR_W = cs->base + OFFSET_DATA;
> +	chip->legacy.IO_ADDR_R = cs->base + nfc->soc_info->data_offset;
> +	chip->legacy.IO_ADDR_W = cs->base + nfc->soc_info->data_offset;
>  	chip->legacy.chip_delay = RB_DELAY_US;
>  	chip->options = NAND_NO_SUBPAGE_WRITE;
>  	chip->legacy.select_chip = ingenic_nand_select_chip;

I think Boris already asked for it, but it would be really great that
you update this driver to not use any legacy interface anymore.

> diff --git a/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
> new file mode 100644
> index 000000000000..83b42881720e
> --- /dev/null
> +++ b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
> @@ -0,0 +1,196 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * JZ4740 ECC controller driver
> + *
> + * Copyright (c) 2019 Paul Cercueil <paul@crapouillou.net>
> + *
> + * based on jz4740-nand.c
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/device.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +
> +#include "ingenic_ecc.h"
> +
> +#define JZ_REG_NAND_ECC_CTRL	0x00
> +#define JZ_REG_NAND_DATA	0x04
> +#define JZ_REG_NAND_PAR0	0x08
> +#define JZ_REG_NAND_PAR1	0x0C
> +#define JZ_REG_NAND_PAR2	0x10
> +#define JZ_REG_NAND_IRQ_STAT	0x14
> +#define JZ_REG_NAND_IRQ_CTRL	0x18
> +#define JZ_REG_NAND_ERR(x)	(0x1C + ((x) << 2))
> +
> +#define JZ_NAND_ECC_CTRL_PAR_READY	BIT(4)
> +#define JZ_NAND_ECC_CTRL_ENCODING	BIT(3)
> +#define JZ_NAND_ECC_CTRL_RS		BIT(2)
> +#define JZ_NAND_ECC_CTRL_RESET		BIT(1)
> +#define JZ_NAND_ECC_CTRL_ENABLE		BIT(0)
> +
> +#define JZ_NAND_STATUS_ERR_COUNT	(BIT(31) | BIT(30) | BIT(29))
> +#define JZ_NAND_STATUS_PAD_FINISH	BIT(4)
> +#define JZ_NAND_STATUS_DEC_FINISH	BIT(3)
> +#define JZ_NAND_STATUS_ENC_FINISH	BIT(2)
> +#define JZ_NAND_STATUS_UNCOR_ERROR	BIT(1)
> +#define JZ_NAND_STATUS_ERROR		BIT(0)
> +
> +static const uint8_t empty_block_ecc[] = {
> +	0xcd, 0x9d, 0x90, 0x58, 0xf4, 0x8b, 0xff, 0xb7, 0x6f
> +};
> +
> +static void jz4740_ecc_init(struct ingenic_ecc *ecc, bool encode)
> +{
> +	uint32_t reg;
> +
> +	/* Clear interrupt status */
> +	writel(0, ecc->base + JZ_REG_NAND_IRQ_STAT);
> +
> +	/* Initialize and enable ECC hardware */
> +	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
> +	reg |= JZ_NAND_ECC_CTRL_RESET;
> +	reg |= JZ_NAND_ECC_CTRL_ENABLE;
> +	reg |= JZ_NAND_ECC_CTRL_RS;
> +	if (encode)
> +		reg |= JZ_NAND_ECC_CTRL_ENCODING;
> +	else
> +		reg &= ~JZ_NAND_ECC_CTRL_ENCODING;
> +
> +	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
> +}
> +
> +static int jz4740_ecc_calculate(struct ingenic_ecc *ecc,
> +				struct ingenic_ecc_params *params,
> +				const u8 *buf, u8 *ecc_code)
> +{
> +	uint32_t reg, status;
> +	unsigned int timeout = 1000;
> +	int i;
> +
> +	jz4740_ecc_init(ecc, true);
> +
> +	do {
> +		status = readl(ecc->base + JZ_REG_NAND_IRQ_STAT);
> +	} while (!(status & JZ_NAND_STATUS_ENC_FINISH) && --timeout);
> +
> +	if (timeout == 0)
> +		return -ETIMEDOUT;
> +
> +	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
> +	reg &= ~JZ_NAND_ECC_CTRL_ENABLE;
> +	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
> +
> +	for (i = 0; i < params->bytes; ++i)
> +		ecc_code[i] = readb(ecc->base + JZ_REG_NAND_PAR0 + i);
> +
> +	/* If the written data is completely 0xff, we also want to write 0xff as
> +	 * ecc, otherwise we will get in trouble when doing subpage writes.
> +	 */

Comment formatting

s/ecc/ECC/ in plain English

> +	if (memcmp(ecc_code, empty_block_ecc, ARRAY_SIZE(empty_block_ecc)) == 0)
> +		memset(ecc_code, 0xff, ARRAY_SIZE(empty_block_ecc));
> +
> +	return 0;
> +}
> +


Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 7/9] mtd: rawnand: ingenic: Add support for the JZ4740

[Paul Cercueil]

On Mon, Mar 4, 2019 at 11:34 AM, Miquel Raynal 
<miquel.raynal@bootlin.com> wrote:
> Hi Paul,
> 
> Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> 
> wrote on Sat,  9 Feb 2019 16:23:03
> -0300:
> 
>>  Add support for probing the ingenic-nand driver on the JZ4740 SoC 
>> from
>>  Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
>>  ECC hardware.
>> 
>>  Signed-off-by: Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>>
>>  ---
>> 
>>  Changes:
>> 
>>  v2: New patch
>> 
>>  v3: Also add support for the hardware ECC of the JZ4740 in this 
>> patch
>> 
>>  v4: - Fix formatting issues
>>      - Add MODULE_* macros
>> 
>>   drivers/mtd/nand/raw/ingenic/Kconfig        |  10 ++
>>   drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
>>   drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 +++++--
>>   drivers/mtd/nand/raw/ingenic/jz4740_ecc.c   | 196 
>> ++++++++++++++++++++++++++++
>>   4 files changed, 244 insertions(+), 11 deletions(-)
>>   create mode 100644 drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
>> 
> 
> [...]
> 
>>   	switch (chip->ecc.mode) {
>>   	case NAND_ECC_HW:
>>  @@ -270,8 +279,8 @@ static int ingenic_nand_init_chip(struct 
>> platform_device *pdev,
>>   		return -ENOMEM;
>>   	mtd->dev.parent = dev;
>> 
>>  -	chip->legacy.IO_ADDR_R = cs->base + OFFSET_DATA;
>>  -	chip->legacy.IO_ADDR_W = cs->base + OFFSET_DATA;
>>  +	chip->legacy.IO_ADDR_R = cs->base + nfc->soc_info->data_offset;
>>  +	chip->legacy.IO_ADDR_W = cs->base + nfc->soc_info->data_offset;
>>   	chip->legacy.chip_delay = RB_DELAY_US;
>>   	chip->options = NAND_NO_SUBPAGE_WRITE;
>>   	chip->legacy.select_chip = ingenic_nand_select_chip;
> 
> I think Boris already asked for it, but it would be really great that
> you update this driver to not use any legacy interface anymore.

I thought I'd send a patch later. But I don't mind doing the update in
this patchset.

>>  diff --git a/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c 
>> b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
>>  new file mode 100644
>>  index 000000000000..83b42881720e
>>  --- /dev/null
>>  +++ b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
>>  @@ -0,0 +1,196 @@
>>  +// SPDX-License-Identifier: GPL-2.0
>>  +/*
>>  + * JZ4740 ECC controller driver
>>  + *
>>  + * Copyright (c) 2019 Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>>
>>  + *
>>  + * based on jz4740-nand.c
>>  + */
>>  +
>>  +#include <linux/bitops.h>
>>  +#include <linux/device.h>
>>  +#include <linux/io.h>
>>  +#include <linux/module.h>
>>  +#include <linux/of_platform.h>
>>  +#include <linux/platform_device.h>
>>  +
>>  +#include "ingenic_ecc.h"
>>  +
>>  +#define JZ_REG_NAND_ECC_CTRL	0x00
>>  +#define JZ_REG_NAND_DATA	0x04
>>  +#define JZ_REG_NAND_PAR0	0x08
>>  +#define JZ_REG_NAND_PAR1	0x0C
>>  +#define JZ_REG_NAND_PAR2	0x10
>>  +#define JZ_REG_NAND_IRQ_STAT	0x14
>>  +#define JZ_REG_NAND_IRQ_CTRL	0x18
>>  +#define JZ_REG_NAND_ERR(x)	(0x1C + ((x) << 2))
>>  +
>>  +#define JZ_NAND_ECC_CTRL_PAR_READY	BIT(4)
>>  +#define JZ_NAND_ECC_CTRL_ENCODING	BIT(3)
>>  +#define JZ_NAND_ECC_CTRL_RS		BIT(2)
>>  +#define JZ_NAND_ECC_CTRL_RESET		BIT(1)
>>  +#define JZ_NAND_ECC_CTRL_ENABLE		BIT(0)
>>  +
>>  +#define JZ_NAND_STATUS_ERR_COUNT	(BIT(31) | BIT(30) | BIT(29))
>>  +#define JZ_NAND_STATUS_PAD_FINISH	BIT(4)
>>  +#define JZ_NAND_STATUS_DEC_FINISH	BIT(3)
>>  +#define JZ_NAND_STATUS_ENC_FINISH	BIT(2)
>>  +#define JZ_NAND_STATUS_UNCOR_ERROR	BIT(1)
>>  +#define JZ_NAND_STATUS_ERROR		BIT(0)
>>  +
>>  +static const uint8_t empty_block_ecc[] = {
>>  +	0xcd, 0x9d, 0x90, 0x58, 0xf4, 0x8b, 0xff, 0xb7, 0x6f
>>  +};
>>  +
>>  +static void jz4740_ecc_init(struct ingenic_ecc *ecc, bool encode)
>>  +{
>>  +	uint32_t reg;
>>  +
>>  +	/* Clear interrupt status */
>>  +	writel(0, ecc->base + JZ_REG_NAND_IRQ_STAT);
>>  +
>>  +	/* Initialize and enable ECC hardware */
>>  +	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
>>  +	reg |= JZ_NAND_ECC_CTRL_RESET;
>>  +	reg |= JZ_NAND_ECC_CTRL_ENABLE;
>>  +	reg |= JZ_NAND_ECC_CTRL_RS;
>>  +	if (encode)
>>  +		reg |= JZ_NAND_ECC_CTRL_ENCODING;
>>  +	else
>>  +		reg &= ~JZ_NAND_ECC_CTRL_ENCODING;
>>  +
>>  +	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
>>  +}
>>  +
>>  +static int jz4740_ecc_calculate(struct ingenic_ecc *ecc,
>>  +				struct ingenic_ecc_params *params,
>>  +				const u8 *buf, u8 *ecc_code)
>>  +{
>>  +	uint32_t reg, status;
>>  +	unsigned int timeout = 1000;
>>  +	int i;
>>  +
>>  +	jz4740_ecc_init(ecc, true);
>>  +
>>  +	do {
>>  +		status = readl(ecc->base + JZ_REG_NAND_IRQ_STAT);
>>  +	} while (!(status & JZ_NAND_STATUS_ENC_FINISH) && --timeout);
>>  +
>>  +	if (timeout == 0)
>>  +		return -ETIMEDOUT;
>>  +
>>  +	reg = readl(ecc->base + JZ_REG_NAND_ECC_CTRL);
>>  +	reg &= ~JZ_NAND_ECC_CTRL_ENABLE;
>>  +	writel(reg, ecc->base + JZ_REG_NAND_ECC_CTRL);
>>  +
>>  +	for (i = 0; i < params->bytes; ++i)
>>  +		ecc_code[i] = readb(ecc->base + JZ_REG_NAND_PAR0 + i);
>>  +
>>  +	/* If the written data is completely 0xff, we also want to write 
>> 0xff as
>>  +	 * ecc, otherwise we will get in trouble when doing subpage 
>> writes.
>>  +	 */
> 
> Comment formatting
> 
> s/ecc/ECC/ in plain English
> 
>>  +	if (memcmp(ecc_code, empty_block_ecc, 
>> ARRAY_SIZE(empty_block_ecc)) == 0)
>>  +		memset(ecc_code, 0xff, ARRAY_SIZE(empty_block_ecc));
>>  +
>>  +	return 0;
>>  +}
>>  +
> 
> 
> Thanks,
> Miquèl



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 7/9] mtd: rawnand: ingenic: Add support for the JZ4740

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Mon, 04 Mar 2019 19:28:49
+0100:

> On Mon, Mar 4, 2019 at 11:34 AM, Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> > Hi Paul,
> > 
> > Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> > wrote on Sat,  9 Feb 2019 16:23:03
> > -0300:
> >   
> >>  Add support for probing the ingenic-nand driver on the JZ4740 SoC >> from
> >>  Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
> >>  ECC hardware.  
> >> >>  Signed-off-by: Paul Cercueil <paul@crapouillou.net >> <mailto:paul@crapouillou.net>>  
> >>  ---  
> >> >>  Changes:
> >> >>  v2: New patch
> >> >>  v3: Also add support for the hardware ECC of the JZ4740 in this >> patch
> >> >>  v4: - Fix formatting issues  
> >>      - Add MODULE_* macros  
> >> >>   drivers/mtd/nand/raw/ingenic/Kconfig        |  10 ++  
> >>   drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
> >>   drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 +++++--
> >>   drivers/mtd/nand/raw/ingenic/jz4740_ecc.c   | 196 >> ++++++++++++++++++++++++++++
> >>   4 files changed, 244 insertions(+), 11 deletions(-)
> >>   create mode 100644 drivers/mtd/nand/raw/ingenic/jz4740_ecc.c  
> >> >   
> > [...]
> >   
> >>   	switch (chip->ecc.mode) {
> >>   	case NAND_ECC_HW:
> >>  @@ -270,8 +279,8 @@ static int ingenic_nand_init_chip(struct >> platform_device *pdev,
> >>   		return -ENOMEM;
> >>   	mtd->dev.parent = dev;  
> >> >>  -	chip->legacy.IO_ADDR_R = cs->base + OFFSET_DATA;  
> >>  -	chip->legacy.IO_ADDR_W = cs->base + OFFSET_DATA;
> >>  +	chip->legacy.IO_ADDR_R = cs->base + nfc->soc_info->data_offset;
> >>  +	chip->legacy.IO_ADDR_W = cs->base + nfc->soc_info->data_offset;
> >>   	chip->legacy.chip_delay = RB_DELAY_US;
> >>   	chip->options = NAND_NO_SUBPAGE_WRITE;
> >>   	chip->legacy.select_chip = ingenic_nand_select_chip;  
> > 
> > I think Boris already asked for it, but it would be really great that
> > you update this driver to not use any legacy interface anymore.  
> 
> I thought I'd send a patch later. But I don't mind doing the update in
> this patchset.

Great! No it's okay, don't delay this patch set, doing it in another
thread is fine.


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 8/9] mtd: rawnand: ingenic: Add support for the JZ4725B

[Paul Cercueil]

The boot ROM of the JZ4725B SoC expects a specific OOB layout on the
NAND, so we use it unconditionally in the ingenic-nand driver.

Also add the jz4725b-bch driver to support the JZ4725B-specific BCH
hardware.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

Changes:

v2: Instead of forcing the OOB layout, leave it to the board code or
    devicetree to decide if the jz4725b-specific layout should be used
    or not.

v3: - Revert the change in v2, as the previous behaviour was correct.
    - Also add support for the hardware BCH of the JZ4725B in this
      patch.

v4: - Add MODULE_* macros
    - Add tweaks suggested by upstream feedback

 drivers/mtd/nand/raw/ingenic/Kconfig        |  10 +
 drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
 drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 ++++-
 drivers/mtd/nand/raw/ingenic/jz4725b_bch.c  | 292 ++++++++++++++++++++++++++++
 4 files changed, 350 insertions(+), 1 deletion(-)
 create mode 100644 drivers/mtd/nand/raw/ingenic/jz4725b_bch.c

diff --git a/drivers/mtd/nand/raw/ingenic/Kconfig b/drivers/mtd/nand/raw/ingenic/Kconfig
index cc663cc15119..497b46b144f2 100644
--- a/drivers/mtd/nand/raw/ingenic/Kconfig
+++ b/drivers/mtd/nand/raw/ingenic/Kconfig
@@ -27,6 +27,16 @@ config MTD_NAND_JZ4740_ECC
 	  This driver can also be built as a module. If so, the module
 	  will be called jz4740-ecc.
 
+config MTD_NAND_JZ4725B_BCH
+	tristate "Hardware BCH support for JZ4725B SoC"
+	select MTD_NAND_INGENIC_ECC
+	help
+	  Enable this driver to support the BCH error-correction hardware
+	  present on the JZ4725B SoC from Ingenic.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called jz4725b-bch.
+
 config MTD_NAND_JZ4780_BCH
 	tristate "Hardware BCH support for JZ4780 SoC"
 	select MTD_NAND_INGENIC_ECC
diff --git a/drivers/mtd/nand/raw/ingenic/Makefile b/drivers/mtd/nand/raw/ingenic/Makefile
index 563b7effcf59..ab2c5f47e5b7 100644
--- a/drivers/mtd/nand/raw/ingenic/Makefile
+++ b/drivers/mtd/nand/raw/ingenic/Makefile
@@ -3,4 +3,5 @@ obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o
 
 obj-$(CONFIG_MTD_NAND_INGENIC_ECC) += ingenic_ecc.o
 obj-$(CONFIG_MTD_NAND_JZ4740_ECC) += jz4740_ecc.o
+obj-$(CONFIG_MTD_NAND_JZ4725B_BCH) += jz4725b_bch.o
 obj-$(CONFIG_MTD_NAND_JZ4780_BCH) += jz4780_bch.o
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
index 036938fdad51..4837bbce7099 100644
--- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
@@ -34,6 +34,7 @@ struct jz_soc_info {
 	unsigned long data_offset;
 	unsigned long addr_offset;
 	unsigned long cmd_offset;
+	const struct mtd_ooblayout_ops *oob_layout;
 };
 
 struct ingenic_nand_cs {
@@ -71,6 +72,41 @@ static inline struct ingenic_nfc *to_ingenic_nfc(struct nand_controller *ctrl)
 	return container_of(ctrl, struct ingenic_nfc, controller);
 }
 
+static int jz4725b_ooblayout_ecc(struct mtd_info *mtd, int section,
+				 struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct nand_ecc_ctrl *ecc = &chip->ecc;
+
+	if (section || !ecc->total)
+		return -ERANGE;
+
+	oobregion->length = ecc->total;
+	oobregion->offset = 3;
+
+	return 0;
+}
+
+static int jz4725b_ooblayout_free(struct mtd_info *mtd, int section,
+				  struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct nand_ecc_ctrl *ecc = &chip->ecc;
+
+	if (section)
+		return -ERANGE;
+
+	oobregion->length = mtd->oobsize - ecc->total - 3;
+	oobregion->offset = 3 + ecc->total;
+
+	return 0;
+}
+
+const struct mtd_ooblayout_ops jz4725b_ooblayout_ops = {
+	.ecc = jz4725b_ooblayout_ecc,
+	.free = jz4725b_ooblayout_free,
+};
+
 static void ingenic_nand_select_chip(struct nand_chip *chip, int chipnr)
 {
 	struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
@@ -211,7 +247,7 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
 		return -EINVAL;
 	}
 
-	mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops);
+	mtd_set_ooblayout(mtd, nfc->soc_info->oob_layout);
 
 	return 0;
 }
@@ -407,16 +443,26 @@ static const struct jz_soc_info jz4740_soc_info = {
 	.data_offset = 0x00000000,
 	.cmd_offset = 0x00008000,
 	.addr_offset = 0x00010000,
+	.oob_layout = &nand_ooblayout_lp_ops,
+};
+
+static const struct jz_soc_info jz4725b_soc_info = {
+	.data_offset = 0x00000000,
+	.cmd_offset = 0x00008000,
+	.addr_offset = 0x00010000,
+	.oob_layout = &jz4725b_ooblayout_ops,
 };
 
 static const struct jz_soc_info jz4780_soc_info = {
 	.data_offset = 0x00000000,
 	.cmd_offset = 0x00400000,
 	.addr_offset = 0x00800000,
+	.oob_layout = &nand_ooblayout_lp_ops,
 };
 
 static const struct of_device_id ingenic_nand_dt_match[] = {
 	{ .compatible = "ingenic,jz4740-nand", .data = &jz4740_soc_info },
+	{ .compatible = "ingenic,jz4725b-nand", .data = &jz4725b_soc_info },
 	{ .compatible = "ingenic,jz4780-nand", .data = &jz4780_soc_info },
 	{},
 };
diff --git a/drivers/mtd/nand/raw/ingenic/jz4725b_bch.c b/drivers/mtd/nand/raw/ingenic/jz4725b_bch.c
new file mode 100644
index 000000000000..f7094c34b5df
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/jz4725b_bch.c
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * JZ4725B BCH controller driver
+ *
+ * Copyright (C) 2019 Paul Cercueil <paul@crapouillou.net>
+ *
+ * Based on jz4780_bch.c
+ */
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include "ingenic_ecc.h"
+
+#define BCH_BHCR			0x0
+#define BCH_BHCSR			0x4
+#define BCH_BHCCR			0x8
+#define BCH_BHCNT			0xc
+#define BCH_BHDR			0x10
+#define BCH_BHPAR0			0x14
+#define BCH_BHERR0			0x28
+#define BCH_BHINT			0x24
+#define BCH_BHINTES			0x3c
+#define BCH_BHINTEC			0x40
+#define BCH_BHINTE			0x38
+
+#define BCH_BHCR_ENCE			BIT(3)
+#define BCH_BHCR_BSEL			BIT(2)
+#define BCH_BHCR_INIT			BIT(1)
+#define BCH_BHCR_BCHE			BIT(0)
+
+#define BCH_BHCNT_DEC_COUNT_SHIFT	16
+#define BCH_BHCNT_DEC_COUNT_MASK	(0x3ff << BCH_BHCNT_DEC_COUNT_SHIFT)
+#define BCH_BHCNT_ENC_COUNT_SHIFT	0
+#define BCH_BHCNT_ENC_COUNT_MASK	(0x3ff << BCH_BHCNT_ENC_COUNT_SHIFT)
+
+#define BCH_BHERR_INDEX0_SHIFT		0
+#define BCH_BHERR_INDEX0_MASK		(0x1fff << BCH_BHERR_INDEX0_SHIFT)
+#define BCH_BHERR_INDEX1_SHIFT		16
+#define BCH_BHERR_INDEX1_MASK		(0x1fff << BCH_BHERR_INDEX1_SHIFT)
+
+#define BCH_BHINT_ERRC_SHIFT		28
+#define BCH_BHINT_ERRC_MASK		(0xf << BCH_BHINT_ERRC_SHIFT)
+#define BCH_BHINT_TERRC_SHIFT		16
+#define BCH_BHINT_TERRC_MASK		(0x7f << BCH_BHINT_TERRC_SHIFT)
+#define BCH_BHINT_ALL_0			BIT(5)
+#define BCH_BHINT_ALL_F			BIT(4)
+#define BCH_BHINT_DECF			BIT(3)
+#define BCH_BHINT_ENCF			BIT(2)
+#define BCH_BHINT_UNCOR			BIT(1)
+#define BCH_BHINT_ERR			BIT(0)
+
+/* Timeout for BCH calculation/correction. */
+#define BCH_TIMEOUT_US			100000
+
+static inline void jz4725b_bch_config_set(struct ingenic_ecc *bch, u32 cfg)
+{
+	writel(cfg, bch->base + BCH_BHCSR);
+}
+
+static inline void jz4725b_bch_config_clear(struct ingenic_ecc *bch, u32 cfg)
+{
+	writel(cfg, bch->base + BCH_BHCCR);
+}
+
+static int jz4725b_bch_init(struct ingenic_ecc *bch,
+			    struct ingenic_ecc_params *params, bool calc_ecc)
+{
+	u32 reg, max_value;
+
+	/* Clear interrupt status. */
+	writel(readl(bch->base + BCH_BHINT), bch->base + BCH_BHINT);
+
+	/* Initialise and enable BCH. */
+	jz4725b_bch_config_clear(bch, 0x1f);
+	jz4725b_bch_config_set(bch, BCH_BHCR_BCHE);
+
+	if (params->strength == 8)
+		jz4725b_bch_config_set(bch, BCH_BHCR_BSEL);
+	else
+		jz4725b_bch_config_clear(bch, BCH_BHCR_BSEL);
+
+	if (calc_ecc) /* calculate ECC from data */
+		jz4725b_bch_config_set(bch, BCH_BHCR_ENCE);
+	else /* correct data from ECC */
+		jz4725b_bch_config_clear(bch, BCH_BHCR_ENCE);
+
+	jz4725b_bch_config_set(bch, BCH_BHCR_INIT);
+
+	max_value = BCH_BHCNT_ENC_COUNT_MASK >> BCH_BHCNT_ENC_COUNT_SHIFT;
+	if (params->size > max_value)
+		return -EINVAL;
+
+	max_value = BCH_BHCNT_DEC_COUNT_MASK >> BCH_BHCNT_DEC_COUNT_SHIFT;
+	if (params->size + params->bytes > max_value)
+		return -EINVAL;
+
+	/* Set up BCH count register. */
+	reg = params->size << BCH_BHCNT_ENC_COUNT_SHIFT;
+	reg |= (params->size + params->bytes) << BCH_BHCNT_DEC_COUNT_SHIFT;
+	writel(reg, bch->base + BCH_BHCNT);
+
+	return 0;
+}
+
+static void jz4725b_bch_disable(struct ingenic_ecc *bch)
+{
+	/* Clear interrupts */
+	writel(readl(bch->base + BCH_BHINT), bch->base + BCH_BHINT);
+
+	/* Disable the hardware */
+	jz4725b_bch_config_clear(bch, BCH_BHCR_BCHE);
+}
+
+static void jz4725b_bch_write_data(struct ingenic_ecc *bch, const u8 *buf,
+				   size_t size)
+{
+	while (size--)
+		writeb(*buf++, bch->base + BCH_BHDR);
+}
+
+static void jz4725b_bch_read_parity(struct ingenic_ecc *bch, u8 *buf,
+				    size_t size)
+{
+	size_t size32 = size / sizeof(u32);
+	size_t size8 = size % sizeof(u32);
+	u32 *dest32;
+	u8 *dest8;
+	u32 val, offset = 0;
+
+	dest32 = (u32 *)buf;
+	while (size32--) {
+		*dest32++ = readl_relaxed(bch->base + BCH_BHPAR0 + offset);
+		offset += sizeof(u32);
+	}
+
+	dest8 = (u8 *)dest32;
+	val = readl_relaxed(bch->base + BCH_BHPAR0 + offset);
+	switch (size8) {
+	case 3:
+		dest8[2] = (val >> 16) & 0xff;
+	case 2: /* fall-through */
+		dest8[1] = (val >> 8) & 0xff;
+	case 1: /* fall-through */
+		dest8[0] = val & 0xff;
+		break;
+	}
+}
+
+static int jz4725b_bch_wait_complete(struct ingenic_ecc *bch, unsigned int irq,
+				     u32 *status)
+{
+	u32 reg;
+	int ret;
+
+	/*
+	 * While we could use interrupts here and sleep until the operation
+	 * completes, the controller works fairly quickly (usually a few
+	 * microseconds) and so the overhead of sleeping until we get an
+	 * interrupt quite noticeably decreases performance.
+	 */
+	ret = readl_relaxed_poll_timeout(bch->base + BCH_BHINT, reg,
+					 reg & irq, 0, BCH_TIMEOUT_US);
+	if (ret)
+		return ret;
+
+	if (status)
+		*status = reg;
+
+	writel(reg, bch->base + BCH_BHINT);
+
+	return 0;
+}
+
+static int jz4725b_calculate(struct ingenic_ecc *bch,
+			     struct ingenic_ecc_params *params,
+			     const u8 *buf, u8 *ecc_code)
+{
+	int ret;
+
+	mutex_lock(&bch->lock);
+	ret = jz4725b_bch_init(bch, params, true);
+	if (ret) {
+		dev_err(bch->dev, "Unable to init BCH with given parameters\n");
+		goto out_disable;
+	}
+
+	jz4725b_bch_write_data(bch, buf, params->size);
+
+	ret = jz4725b_bch_wait_complete(bch, BCH_BHINT_ENCF, NULL);
+	if (ret) {
+		dev_err(bch->dev, "timed out while calculating ECC\n");
+		goto out_disable;
+	}
+
+	jz4725b_bch_read_parity(bch, ecc_code, params->bytes);
+
+out_disable:
+	jz4725b_bch_disable(bch);
+	mutex_unlock(&bch->lock);
+
+	return ret;
+}
+
+static int jz4725b_correct(struct ingenic_ecc *bch,
+			   struct ingenic_ecc_params *params,
+			   u8 *buf, u8 *ecc_code)
+{
+	u32 reg, errors, bit;
+	unsigned int i;
+	int ret;
+
+	mutex_lock(&bch->lock);
+
+	ret = jz4725b_bch_init(bch, params, false);
+	if (ret) {
+		dev_err(bch->dev, "Unable to init BCH with given parameters\n");
+		goto out;
+	}
+
+	jz4725b_bch_write_data(bch, buf, params->size);
+	jz4725b_bch_write_data(bch, ecc_code, params->bytes);
+
+	ret = jz4725b_bch_wait_complete(bch, BCH_BHINT_DECF, &reg);
+	if (ret) {
+		dev_err(bch->dev, "timed out while correcting data\n");
+		goto out;
+	}
+
+	if (reg & (BCH_BHINT_ALL_F | BCH_BHINT_ALL_0)) {
+		/* Data and ECC is all 0xff or 0x00 - nothing to correct */
+		ret = 0;
+		goto out;
+	}
+
+	if (reg & BCH_BHINT_UNCOR) {
+		/* Uncorrectable ECC error */
+		ret = -EBADMSG;
+		goto out;
+	}
+
+	errors = (reg & BCH_BHINT_ERRC_MASK) >> BCH_BHINT_ERRC_SHIFT;
+
+	/* Correct any detected errors. */
+	for (i = 0; i < errors; i++) {
+		if (i & 1) {
+			bit = (reg & BCH_BHERR_INDEX1_MASK) >> BCH_BHERR_INDEX1_SHIFT;
+		} else {
+			reg = readl(bch->base + BCH_BHERR0 + (i * 4));
+			bit = (reg & BCH_BHERR_INDEX0_MASK) >> BCH_BHERR_INDEX0_SHIFT;
+		}
+
+		buf[(bit >> 3)] ^= BIT(bit & 0x7);
+	}
+
+out:
+	jz4725b_bch_disable(bch);
+	mutex_unlock(&bch->lock);
+
+	return ret;
+}
+
+static const struct ingenic_ecc_ops jz4725b_bch_ops = {
+	.disable = jz4725b_bch_disable,
+	.calculate = jz4725b_calculate,
+	.correct = jz4725b_correct,
+};
+
+static const struct of_device_id jz4725b_bch_dt_match[] = {
+	{ .compatible = "ingenic,jz4725b-bch", .data = &jz4725b_bch_ops },
+	{},
+};
+MODULE_DEVICE_TABLE(of, jz4725b_bch_dt_match);
+
+static struct platform_driver jz4725b_bch_driver = {
+	.probe		= ingenic_ecc_probe,
+	.driver	= {
+		.name	= "jz4725b-bch",
+		.of_match_table = jz4725b_bch_dt_match,
+	},
+};
+module_platform_driver(jz4725b_bch_driver);
+
+MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
+MODULE_DESCRIPTION("Ingenic JZ4725B BCH controller driver");
+MODULE_LICENSE("GPL v2");
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 8/9] mtd: rawnand: ingenic: Add support for the JZ4725B

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Sat,  9 Feb 2019 16:23:04
-0300:

> The boot ROM of the JZ4725B SoC expects a specific OOB layout on the
> NAND, so we use it unconditionally in the ingenic-nand driver.
> 
> Also add the jz4725b-bch driver to support the JZ4725B-specific BCH
> hardware.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> Changes:
> 
> v2: Instead of forcing the OOB layout, leave it to the board code or
>     devicetree to decide if the jz4725b-specific layout should be used
>     or not.
> 
> v3: - Revert the change in v2, as the previous behaviour was correct.
>     - Also add support for the hardware BCH of the JZ4725B in this
>       patch.
> 
> v4: - Add MODULE_* macros
>     - Add tweaks suggested by upstream feedback
> 
>  drivers/mtd/nand/raw/ingenic/Kconfig        |  10 +
>  drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
>  drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 ++++-
>  drivers/mtd/nand/raw/ingenic/jz4725b_bch.c  | 292 ++++++++++++++++++++++++++++
>  4 files changed, 350 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/mtd/nand/raw/ingenic/jz4725b_bch.c
> 

[...]

> +static int jz4725b_calculate(struct ingenic_ecc *bch,
> +			     struct ingenic_ecc_params *params,
> +			     const u8 *buf, u8 *ecc_code)
> +{
> +	int ret;
> +
> +	mutex_lock(&bch->lock);
> +	ret = jz4725b_bch_init(bch, params, true);

I really don't like this bch_init name. A BCH initialization is what is
supposed to be done only once (probably at boot time), can you find a
better name or a better organization of the correct/calculate path?

> +	if (ret) {
> +		dev_err(bch->dev, "Unable to init BCH with given parameters\n");
> +		goto out_disable;
> +	}
> +
> +	jz4725b_bch_write_data(bch, buf, params->size);
> +
> +	ret = jz4725b_bch_wait_complete(bch, BCH_BHINT_ENCF, NULL);
> +	if (ret) {
> +		dev_err(bch->dev, "timed out while calculating ECC\n");
> +		goto out_disable;
> +	}
> +
> +	jz4725b_bch_read_parity(bch, ecc_code, params->bytes);
> +
> +out_disable:
> +	jz4725b_bch_disable(bch);
> +	mutex_unlock(&bch->lock);
> +
> +	return ret;
> +}
> +

[...]

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 8/9] mtd: rawnand: ingenic: Add support for the JZ4725B

[Paul Cercueil]

On Mon, Mar 4, 2019 at 11:35 AM, Miquel Raynal 
<miquel.raynal@bootlin.com> wrote:
> Hi Paul,
> 
> Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> 
> wrote on Sat,  9 Feb 2019 16:23:04
> -0300:
> 
>>  The boot ROM of the JZ4725B SoC expects a specific OOB layout on the
>>  NAND, so we use it unconditionally in the ingenic-nand driver.
>> 
>>  Also add the jz4725b-bch driver to support the JZ4725B-specific BCH
>>  hardware.
>> 
>>  Signed-off-by: Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>>
>>  ---
>> 
>>  Changes:
>> 
>>  v2: Instead of forcing the OOB layout, leave it to the board code or
>>      devicetree to decide if the jz4725b-specific layout should be 
>> used
>>      or not.
>> 
>>  v3: - Revert the change in v2, as the previous behaviour was 
>> correct.
>>      - Also add support for the hardware BCH of the JZ4725B in this
>>        patch.
>> 
>>  v4: - Add MODULE_* macros
>>      - Add tweaks suggested by upstream feedback
>> 
>>   drivers/mtd/nand/raw/ingenic/Kconfig        |  10 +
>>   drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
>>   drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 ++++-
>>   drivers/mtd/nand/raw/ingenic/jz4725b_bch.c  | 292 
>> ++++++++++++++++++++++++++++
>>   4 files changed, 350 insertions(+), 1 deletion(-)
>>   create mode 100644 drivers/mtd/nand/raw/ingenic/jz4725b_bch.c
>> 
> 
> [...]
> 
>>  +static int jz4725b_calculate(struct ingenic_ecc *bch,
>>  +			     struct ingenic_ecc_params *params,
>>  +			     const u8 *buf, u8 *ecc_code)
>>  +{
>>  +	int ret;
>>  +
>>  +	mutex_lock(&bch->lock);
>>  +	ret = jz4725b_bch_init(bch, params, true);
> 
> I really don't like this bch_init name. A BCH initialization is what 
> is
> supposed to be done only once (probably at boot time), can you find a
> better name or a better organization of the correct/calculate path?

jz4725b_bch_setup() maybe?

>>  +	if (ret) {
>>  +		dev_err(bch->dev, "Unable to init BCH with given parameters\n");
>>  +		goto out_disable;
>>  +	}
>>  +
>>  +	jz4725b_bch_write_data(bch, buf, params->size);
>>  +
>>  +	ret = jz4725b_bch_wait_complete(bch, BCH_BHINT_ENCF, NULL);
>>  +	if (ret) {
>>  +		dev_err(bch->dev, "timed out while calculating ECC\n");
>>  +		goto out_disable;
>>  +	}
>>  +
>>  +	jz4725b_bch_read_parity(bch, ecc_code, params->bytes);
>>  +
>>  +out_disable:
>>  +	jz4725b_bch_disable(bch);
>>  +	mutex_unlock(&bch->lock);
>>  +
>>  +	return ret;
>>  +}
>>  +
> 
> [...]
> 
> Thanks,
> Miquèl



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 8/9] mtd: rawnand: ingenic: Add support for the JZ4725B

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Mon, 04 Mar 2019 19:30:04
+0100:

> On Mon, Mar 4, 2019 at 11:35 AM, Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> > Hi Paul,
> > 
> > Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> > wrote on Sat,  9 Feb 2019 16:23:04
> > -0300:
> >   
> >>  The boot ROM of the JZ4725B SoC expects a specific OOB layout on the
> >>  NAND, so we use it unconditionally in the ingenic-nand driver.  
> >> >>  Also add the jz4725b-bch driver to support the JZ4725B-specific BCH  
> >>  hardware.  
> >> >>  Signed-off-by: Paul Cercueil <paul@crapouillou.net >> <mailto:paul@crapouillou.net>>  
> >>  ---  
> >> >>  Changes:
> >> >>  v2: Instead of forcing the OOB layout, leave it to the board code or  
> >>      devicetree to decide if the jz4725b-specific layout should be >> used
> >>      or not.  
> >> >>  v3: - Revert the change in v2, as the previous behaviour was >> correct.  
> >>      - Also add support for the hardware BCH of the JZ4725B in this
> >>        patch.  
> >> >>  v4: - Add MODULE_* macros  
> >>      - Add tweaks suggested by upstream feedback  
> >> >>   drivers/mtd/nand/raw/ingenic/Kconfig        |  10 +  
> >>   drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
> >>   drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 ++++-
> >>   drivers/mtd/nand/raw/ingenic/jz4725b_bch.c  | 292 >> ++++++++++++++++++++++++++++
> >>   4 files changed, 350 insertions(+), 1 deletion(-)
> >>   create mode 100644 drivers/mtd/nand/raw/ingenic/jz4725b_bch.c  
> >> >   
> > [...]
> >   
> >>  +static int jz4725b_calculate(struct ingenic_ecc *bch,
> >>  +			     struct ingenic_ecc_params *params,
> >>  +			     const u8 *buf, u8 *ecc_code)
> >>  +{
> >>  +	int ret;
> >>  +
> >>  +	mutex_lock(&bch->lock);
> >>  +	ret = jz4725b_bch_init(bch, params, true);  
> > 
> > I really don't like this bch_init name. A BCH initialization is what > is
> > supposed to be done only once (probably at boot time), can you find a
> > better name or a better organization of the correct/calculate path?  
> 
> jz4725b_bch_setup() maybe?

Unless I am not understanding what this does, I don't get why you would
need to do this setup everytime you want to use the ECC engine. Are you
sure this is needed?


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 8/9] mtd: rawnand: ingenic: Add support for the JZ4725B

[Paul Cercueil]

Hi Miquel,

Le lun. 4 mars 2019 à 16:09, Miquel Raynal <miquel.raynal@bootlin.com> 
a écrit :
> Hi Paul,
> 
> Paul Cercueil <paul@crapouillou.net> wrote on Mon, 04 Mar 2019 
> 19:30:04
> +0100:
> 
>>  On Mon, Mar 4, 2019 at 11:35 AM, Miquel Raynal 
>> <miquel.raynal@bootlin.com> wrote:
>>  > Hi Paul,
>>  >
>>  > Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>> > wrote on Sat,  9 Feb 2019 16:23:04
>>  > -0300:
>>  >
>>  >>  The boot ROM of the JZ4725B SoC expects a specific OOB layout 
>> on the
>>  >>  NAND, so we use it unconditionally in the ingenic-nand driver.
>>  >> >>  Also add the jz4725b-bch driver to support the 
>> JZ4725B-specific BCH
>>  >>  hardware.
>>  >> >>  Signed-off-by: Paul Cercueil <paul@crapouillou.net >> 
>> <mailto:paul@crapouillou.net>>
>>  >>  ---
>>  >> >>  Changes:
>>  >> >>  v2: Instead of forcing the OOB layout, leave it to the board 
>> code or
>>  >>      devicetree to decide if the jz4725b-specific layout should 
>> be >> used
>>  >>      or not.
>>  >> >>  v3: - Revert the change in v2, as the previous behaviour was 
>> >> correct.
>>  >>      - Also add support for the hardware BCH of the JZ4725B in 
>> this
>>  >>        patch.
>>  >> >>  v4: - Add MODULE_* macros
>>  >>      - Add tweaks suggested by upstream feedback
>>  >> >>   drivers/mtd/nand/raw/ingenic/Kconfig        |  10 +
>>  >>   drivers/mtd/nand/raw/ingenic/Makefile       |   1 +
>>  >>   drivers/mtd/nand/raw/ingenic/ingenic_nand.c |  48 ++++-
>>  >>   drivers/mtd/nand/raw/ingenic/jz4725b_bch.c  | 292 >> 
>> ++++++++++++++++++++++++++++
>>  >>   4 files changed, 350 insertions(+), 1 deletion(-)
>>  >>   create mode 100644 drivers/mtd/nand/raw/ingenic/jz4725b_bch.c
>>  >> >
>>  > [...]
>>  >
>>  >>  +static int jz4725b_calculate(struct ingenic_ecc *bch,
>>  >>  +			     struct ingenic_ecc_params *params,
>>  >>  +			     const u8 *buf, u8 *ecc_code)
>>  >>  +{
>>  >>  +	int ret;
>>  >>  +
>>  >>  +	mutex_lock(&bch->lock);
>>  >>  +	ret = jz4725b_bch_init(bch, params, true);
>>  >
>>  > I really don't like this bch_init name. A BCH initialization is 
>> what > is
>>  > supposed to be done only once (probably at boot time), can you 
>> find a
>>  > better name or a better organization of the correct/calculate 
>> path?
>> 
>>  jz4725b_bch_setup() maybe?
> 
> Unless I am not understanding what this does, I don't get why you 
> would
> need to do this setup everytime you want to use the ECC engine. Are 
> you
> sure this is needed?

It configures the hardware for a new ECC encoding or decoding sequence, 
so
yes, it has to be done everytime.

-Paul


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 9/9] mtd: rawnand: ingenic: Add ooblayout for the Qi Ben Nanonote

[Paul Cercueil]

The Ben Nanonote from Qi Hardware expects a specific OOB layout on its
NAND.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---

Changes:

v2: New patch

v3: Use the qi,lb60 layout unconditionally if we detect that we're
    running on that board.

v4: No change

 drivers/mtd/nand/raw/ingenic/ingenic_nand.c | 41 ++++++++++++++++++++++++++++-
 1 file changed, 40 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
index 4837bbce7099..3c4ad6d79764 100644
--- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
@@ -72,6 +72,41 @@ static inline struct ingenic_nfc *to_ingenic_nfc(struct nand_controller *ctrl)
 	return container_of(ctrl, struct ingenic_nfc, controller);
 }
 
+static int qi_lb60_ooblayout_ecc(struct mtd_info *mtd, int section,
+				 struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct nand_ecc_ctrl *ecc = &chip->ecc;
+
+	if (section || !ecc->total)
+		return -ERANGE;
+
+	oobregion->length = ecc->total;
+	oobregion->offset = 12;
+
+	return 0;
+}
+
+static int qi_lb60_ooblayout_free(struct mtd_info *mtd, int section,
+				  struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct nand_ecc_ctrl *ecc = &chip->ecc;
+
+	if (section)
+		return -ERANGE;
+
+	oobregion->length = mtd->oobsize - ecc->total - 12;
+	oobregion->offset = 12 + ecc->total;
+
+	return 0;
+}
+
+const struct mtd_ooblayout_ops qi_lb60_ooblayout_ops = {
+	.ecc = qi_lb60_ooblayout_ecc,
+	.free = qi_lb60_ooblayout_free,
+};
+
 static int jz4725b_ooblayout_ecc(struct mtd_info *mtd, int section,
 				 struct mtd_oob_region *oobregion)
 {
@@ -247,7 +282,11 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
 		return -EINVAL;
 	}
 
-	mtd_set_ooblayout(mtd, nfc->soc_info->oob_layout);
+	/* For legacy reasons we use a different layout on the qi,lb60 board. */
+	if (of_machine_is_compatible("qi,lb60"))
+		mtd_set_ooblayout(mtd, &qi_lb60_ooblayout_ops);
+	else
+		mtd_set_ooblayout(mtd, nfc->soc_info->oob_layout);
 
 	return 0;
 }
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[Rob Herring]

On Sat,  9 Feb 2019 16:22:57 -0300, Paul Cercueil wrote:
> Add compatible strings to probe the jz4780-nand and jz4780-bch drivers
> from devicetree on the JZ4725B and JZ4740 SoCs from Ingenic.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> Changes:
> 
> v2: - Change 'ingenic,jz4725b-nand' compatible string to
>       'ingenic,jz4740-nand' to reflect driver change
>     - Add 'ingenic,jz4740-bch' compatible string
>     - Document 'ingenic,oob-layout' property
> 
> v3: - Removed 'ingenic,oob-layout' property
>     - Update compatible strings to what the driver supports
> 
> v4: No change
> 
>  Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt | 10 ++++++++--
>  1 file changed, 8 insertions(+), 2 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[Miquel Raynal]

Hi Paul,

Paul Cercueil <paul@crapouillou.net> wrote on Sat,  9 Feb 2019 16:22:57
-0300:

> Add compatible strings to probe the jz4780-nand and jz4780-bch drivers
> from devicetree on the JZ4725B and JZ4740 SoCs from Ingenic.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> 
> Changes:
> 
> v2: - Change 'ingenic,jz4725b-nand' compatible string to
>       'ingenic,jz4740-nand' to reflect driver change
>     - Add 'ingenic,jz4740-bch' compatible string
>     - Document 'ingenic,oob-layout' property
> 
> v3: - Removed 'ingenic,oob-layout' property
>     - Update compatible strings to what the driver supports
> 
> v4: No change
> 
>  Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt | 10 ++++++++--
>  1 file changed, 8 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> index 29ea5853ca91..a5b940f18bf6 100644
> --- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> @@ -6,7 +6,10 @@ memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
>  be children of the NEMC node.
>  
>  Required NAND controller device properties:
> -- compatible: Should be set to "ingenic,jz4780-nand".
> +- compatible: Should be one of:
> +  * ingenic,jz4740-nand
> +  * ingenic,jz4725b-nand
> +  * ingenic,jz4780-nand

Wouldn't "-nand-controller" suffix be better? Of course in the driver
you should still check for jz4780-nand.

>  - reg: For each bank with a NAND chip attached, should specify a bank number,
>    an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
>  
> @@ -72,7 +75,10 @@ NAND devices. The following is a description of the device properties for a
>  BCH controller.
>  
>  Required BCH properties:
> -- compatible: Should be set to "ingenic,jz4780-bch".
> +- compatible: Should be one of:
> +  * ingenic,jz4740-ecc
> +  * ingenic,jz4725b-bch
> +  * ingenic,jz4780-bch
>  - reg: Should specify the BCH controller registers location and length.
>  - clocks: Clock for the BCH controller.
>  

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[Paul Cercueil]

Hi Miquel,

On Mon, Mar 4, 2019 at 10:45 AM, Miquel Raynal 
<miquel.raynal@bootlin.com> wrote:
> Hi Paul,
> 
> Paul Cercueil <paul@crapouillou.net <mailto:paul@crapouillou.net>> 
> wrote on Sat,  9 Feb 2019 16:22:57
> -0300:
> 
>>  Add compatible strings to probe the jz4780-nand and jz4780-bch 
>> drivers
>>  from devicetree on the JZ4725B and JZ4740 SoCs from Ingenic.
>> 
>>  Signed-off-by: Paul Cercueil <paul@crapouillou.net 
>> <mailto:paul@crapouillou.net>>
>>  ---
>> 
>>  Changes:
>> 
>>  v2: - Change 'ingenic,jz4725b-nand' compatible string to
>>        'ingenic,jz4740-nand' to reflect driver change
>>      - Add 'ingenic,jz4740-bch' compatible string
>>      - Document 'ingenic,oob-layout' property
>> 
>>  v3: - Removed 'ingenic,oob-layout' property
>>      - Update compatible strings to what the driver supports
>> 
>>  v4: No change
>> 
>>   Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt | 10 
>> ++++++++--
>>   1 file changed, 8 insertions(+), 2 deletions(-)
>> 
>>  diff --git 
>> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt 
>> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  index 29ea5853ca91..a5b940f18bf6 100644
>>  --- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  @@ -6,7 +6,10 @@ memory-controllers/ingenic,jz4780-nemc.txt), and 
>> thus NAND device nodes must
>>   be children of the NEMC node.
>> 
>>   Required NAND controller device properties:
>>  -- compatible: Should be set to "ingenic,jz4780-nand".
>>  +- compatible: Should be one of:
>>  +  * ingenic,jz4740-nand
>>  +  * ingenic,jz4725b-nand
>>  +  * ingenic,jz4780-nand
> 
> Wouldn't "-nand-controller" suffix be better? Of course in the driver
> you should still check for jz4780-nand.

So I would be compatible with:
* ingenic,jz4740-nand-controller
* ingenic,jz4725b-nand-controller
* ingenic,jz4780-nand
?

>>   - reg: For each bank with a NAND chip attached, should specify a 
>> bank number,
>>     an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC 
>> bank).
>> 
>>  @@ -72,7 +75,10 @@ NAND devices. The following is a description of 
>> the device properties for a
>>   BCH controller.
>> 
>>   Required BCH properties:
>>  -- compatible: Should be set to "ingenic,jz4780-bch".
>>  +- compatible: Should be one of:
>>  +  * ingenic,jz4740-ecc
>>  +  * ingenic,jz4725b-bch
>>  +  * ingenic,jz4780-bch
>>   - reg: Should specify the BCH controller registers location and 
>> length.
>>   - clocks: Clock for the BCH controller.
>> 
> 
> Thanks,
> Miquèl



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[Miquel Raynal]

Hi Paul,

> >>  --- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> >>  +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> >>  @@ -6,7 +6,10 @@ memory-controllers/ingenic,jz4780-nemc.txt), and >> thus NAND device nodes must
> >>   be children of the NEMC node.  
> >> >>   Required NAND controller device properties:  
> >>  -- compatible: Should be set to "ingenic,jz4780-nand".
> >>  +- compatible: Should be one of:
> >>  +  * ingenic,jz4740-nand
> >>  +  * ingenic,jz4725b-nand
> >>  +  * ingenic,jz4780-nand  
> > 
> > Wouldn't "-nand-controller" suffix be better? Of course in the driver
> > you should still check for jz4780-nand.  
> 
> So I would be compatible with:
> * ingenic,jz4740-nand-controller
> * ingenic,jz4725b-nand-controller
> * ingenic,jz4780-nand
> ?

From a driver POV I would even prefer ingenic,jz4780-nand-controller. I
don't know what's best here. Maybe Boris or Rob can help?


Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[Paul Cercueil]

Hi,

Le lun. 4 mars 2019 à 15:51, Miquel Raynal <miquel.raynal@bootlin.com> 
a écrit :
> Hi Paul,
> 
>>  >>  --- 
>> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  >>  +++ 
>> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
>>  >>  @@ -6,7 +6,10 @@ memory-controllers/ingenic,jz4780-nemc.txt), 
>> and >> thus NAND device nodes must
>>  >>   be children of the NEMC node.
>>  >> >>   Required NAND controller device properties:
>>  >>  -- compatible: Should be set to "ingenic,jz4780-nand".
>>  >>  +- compatible: Should be one of:
>>  >>  +  * ingenic,jz4740-nand
>>  >>  +  * ingenic,jz4725b-nand
>>  >>  +  * ingenic,jz4780-nand
>>  >
>>  > Wouldn't "-nand-controller" suffix be better? Of course in the 
>> driver
>>  > you should still check for jz4780-nand.
>> 
>>  So I would be compatible with:
>>  * ingenic,jz4740-nand-controller
>>  * ingenic,jz4725b-nand-controller
>>  * ingenic,jz4780-nand
>>  ?
> 
> From a driver POV I would even prefer ingenic,jz4780-nand-controller. 
> I
> don't know what's best here. Maybe Boris or Rob can help?

The "ingenic,jz4780-nand" compatible string is already out there and 
used
in devicetree files, so I wouldn't change it just for the sake of it.

-Paul


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] dt-bindings: mtd: ingenic: Add compatible strings for JZ4740 and JZ4725B

[Boris Brezillon]

On Wed, 13 Mar 2019 09:55:34 -0300
Paul Cercueil <paul@crapouillou.net> wrote:

> Hi,
> 
> Le lun. 4 mars 2019 à 15:51, Miquel Raynal <miquel.raynal@bootlin.com> 
> a écrit :
> > Hi Paul,
> >   
> >>  >>  ---   
> >> a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt  
> >>  >>  +++   
> >> b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt  
> >>  >>  @@ -6,7 +6,10 @@ memory-controllers/ingenic,jz4780-nemc.txt),   
> >> and >> thus NAND device nodes must  
> >>  >>   be children of the NEMC node.  
> >>  >> >>   Required NAND controller device properties:  
> >>  >>  -- compatible: Should be set to "ingenic,jz4780-nand".
> >>  >>  +- compatible: Should be one of:
> >>  >>  +  * ingenic,jz4740-nand
> >>  >>  +  * ingenic,jz4725b-nand
> >>  >>  +  * ingenic,jz4780-nand  
> >>  >
> >>  > Wouldn't "-nand-controller" suffix be better? Of course in the   
> >> driver  
> >>  > you should still check for jz4780-nand.  
> >> 
> >>  So I would be compatible with:
> >>  * ingenic,jz4740-nand-controller
> >>  * ingenic,jz4725b-nand-controller
> >>  * ingenic,jz4780-nand
> >>  ?  
> > 
> > From a driver POV I would even prefer ingenic,jz4780-nand-controller. 
> > I
> > don't know what's best here. Maybe Boris or Rob can help?

Let's keep it consistent and have all compatibles follow the old
naming scheme (ingenic,<soc>-nand). But yes, for new drivers, I agree
that -nand-controller is better than just -nand.


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/