linux-mtd.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Boris Brezillon <boris.brezillon@collabora.com>
To: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: s.hauer@pengutronix.de, Greg Ungerer <gerg@kernel.org>,
	linux-mtd@lists.infradead.org,
	Michael Nazzareno Trimarchi <michael@amarulasolutions.com>,
	Boris Brezillon <bbrezillon@kernel.org>
Subject: Re: GPMI iMX6ull timeout on DMA
Date: Tue, 30 Jul 2019 10:58:43 +0200	[thread overview]
Message-ID: <20190730105843.1f587554@collabora.com> (raw)
In-Reply-To: <20190730103822.7576645d@xps13>

On Tue, 30 Jul 2019 10:38:22 +0200
Miquel Raynal <miquel.raynal@bootlin.com> wrote:

> Hi Greg,
> 
> Greg Ungerer <gerg@kernel.org> wrote on Tue, 30 Jul 2019 16:06:55 +1000:
> 
> > Hi Miquel,
> > 
> > On 30/7/19 10:41 am, Greg Ungerer wrote:  
> > > On 30/7/19 10:28 am, Greg Ungerer wrote:    
> > >> On 29/7/19 10:47 pm, Miquel Raynal wrote:    
> > >>> Greg Ungerer <gerg@kernel.org> wrote on Mon, 29 Jul 2019 22:33:56 +1000:    
> > >>>> On 29/7/19 6:36 pm, Miquel Raynal wrote:    
> > >>>>> Greg Ungerer <gerg@kernel.org> wrote on Mon, 29 Jul 2019 16:41:51 +1000:    
> > > [snip]    
> > >>>>>> nand: timing mode 5 not acknowledged by the NAND chip    
> > >>>>>
> > >>>>> What is the final timing mode used? Most of us tested in mode 5 I
> > >>>>> guess, maybe mode 4 is broken (don't know if this is the one used here,
> > >>>>> neither why mode 5 is refused). Can you please try by limiting the mode
> > >>>>> to 0, 1, 2... until, hopefully, we narrow down to the failing mode.    
> > >>>>
> > >>>> Sure, how to do that?    
> > >>>
> > >>> This loop [1] tries to configure each mode (5, 4, ...) until one
> > >>> succeeds (default is 0: must always work). Please try to limit mode to
> > >>> 0, 1, etc.
> > >>>
> > >>> Mode 0 should work.
> > >>>
> > >>> [1] https://elixir.bootlin.com/linux/v5.3-rc1/source/drivers/mtd/nand/raw/nand_base.c#L933    
> > >>
> > >> The normal behavior - which usually works - has
> > >> chip->onfi_timing_mode_default=5 here. So in other words on the first pass
> > >> through this loop it is checking mode 5, and setting it as the default.
> > >>
> > >> I am running a test/reboot loop now waiting for failure to see
> > >> if it is still using mode 5 in that case.    
> > > 
> > > With this trace in place:
> > > 
> > > --- a/linux/drivers/mtd/nand/raw/nand_base.c
> > > +++ b/linux/drivers/mtd/nand/raw/nand_base.c
> > > @@ -910,6 +910,7 @@ static int nand_init_data_interface(struct nand_chip *chip)
> > >          }
> > > 
> > >          for (mode = fls(modes) - 1; mode >= 0; mode--) {
> > > +               printk("%s(%d): checking mode=%d\n", __FILE__, __LINE__, mode);
> > >                  ret = onfi_fill_data_interface(chip, NAND_SDR_IFACE, mode);
> > >                  if (ret)
> > >                          continue;
> > > @@ -923,10 +924,12 @@ static int nand_init_data_interface(struct nand_chip *chip)
> > >                                                   &chip->data_interface);
> > >                  if (!ret) {
> > >                          chip->onfi_timing_mode_default = mode;
> > > +                       printk("%s(%d): BREAKING AT mode=%d\n", __FILE__, __LINE__, mode);
> > >                          break;
> > >                  }
> > >          }
> > > 
> > > +       printk("%s(%d): chip->onfi_timing_mode_default=%d\n", __FILE__, __LINE__, chip->onfi_timing_mode_default);
> > >          return 0;
> > >   }
> > > 
> > > 
> > > First NAND failure gives this:
> > > 
> > > nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
> > > nand: Micron MT29F2G08ABAEAWP
> > > nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
> > > gpmi-nand 1806000.gpmi-nand: use legacy bch geometry
> > > drivers/mtd/nand/raw/nand_base.c(913): checking mode=5
> > > drivers/mtd/nand/raw/nand_base.c(927): BREAKING AT mode=5
> > > drivers/mtd/nand/raw/nand_base.c(932): chip->onfi_timing_mode_default=5
> > > gpmi-nand 1806000.gpmi-nand: DMA timeout, last DMA
> > > gpmi-nand 1806000.gpmi-nand: Show GPMI registers :
> > > gpmi-nand 1806000.gpmi-nand: offset 0x000 : 0x20830002
> > > gpmi-nand 1806000.gpmi-nand: offset 0x010 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x020 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x030 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x040 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x050 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x060 : 0x01c6800c
> > > gpmi-nand 1806000.gpmi-nand: offset 0x070 : 0x00010101
> > > gpmi-nand 1806000.gpmi-nand: offset 0x080 : 0xe0000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x090 : 0x23023336
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0a0 : 0x000001ee
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0b0 : 0xff000001
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0c0 : 0x00000100
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0d0 : 0x05020000
> > > gpmi-nand 1806000.gpmi-nand: Show BCH registers :
> > > gpmi-nand 1806000.gpmi-nand: offset 0x000 : 0x00000100
> > > gpmi-nand 1806000.gpmi-nand: offset 0x010 : 0x00000010
> > > gpmi-nand 1806000.gpmi-nand: offset 0x020 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x030 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x040 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x050 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x060 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x070 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x080 : 0x030a2080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x090 : 0x083e2080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0a0 : 0x070a4080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0b0 : 0x10da4080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0c0 : 0x070a4080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0d0 : 0x10da4080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0e0 : 0x070a4080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x0f0 : 0x10da4080
> > > gpmi-nand 1806000.gpmi-nand: offset 0x100 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x110 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x120 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x130 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x140 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x150 : 0x20484342
> > > gpmi-nand 1806000.gpmi-nand: offset 0x160 : 0x01000000
> > > gpmi-nand 1806000.gpmi-nand: offset 0x170 : 0x00000000
> > > gpmi-nand 1806000.gpmi-nand: BCH Geometry :
> > > GF length              : 13
> > > ECC Strength           : 8
> > > Page Size in Bytes     : 2110
> > > Metadata Size in Bytes : 10
> > > ECC Chunk0 Size in Bytes: 512
> > > ECC Chunkn Size in Bytes: 512
> > > ECC Chunk Count        : 4
> > > Payload Size in Bytes  : 2048
> > > Auxiliary Size in Bytes: 16
> > > Auxiliary Status Offset: 12
> > > Block Mark Byte Offset : 1999
> > > Block Mark Bit Offset  : 0
> > > gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -110
> > > nand: timing mode 5 not acknowledged by the NAND chip
> > > gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22    
> > 
> > Not sure if this is a useful data point... But I modified that
> > nand_init_data_interface() loop to start checking from data mode 4.
> > So now on every boot it defaults to mode 4. That has been running
> > most of the day, up to 900 boot cycles now, no failures.  
> 
> Ok so after having chatted quite a bit with Boris, it is very likely
> that, for these chips, the timings in mode 5 are too tight. It could
> fail the GET_FEATURES once in mode 5. Can you please dump every single
> intermediate value in gpmi_nfc_compute_timings() (period, *_cycles,
> use of half pêriods, tRP, sample delay, etc) as well as the content
> of /sys/kernel/debug/clk/clk_summary (you'll need debugfs support
> enabled and mounted).

Not sure the clk will stay at the rate it was set during the timing
selection. Can you also add a trace printing the result of
clk_get_rate(r->clock[0], hw->clk_rate) here [1]?

[1]https://elixir.bootlin.com/linux/v5.3-rc1/source/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c#L711

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

  reply	other threads:[~2019-07-30  8:59 UTC|newest]

Thread overview: 85+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-29  6:41 GPMI iMX6ull timeout on DMA Greg Ungerer
2019-07-29  8:36 ` Miquel Raynal
2019-07-29  8:42   ` Michael Nazzareno Trimarchi
2019-07-29 12:18     ` Greg Ungerer
2019-07-29 12:20       ` Michael Nazzareno Trimarchi
2019-07-29 12:33   ` Greg Ungerer
2019-07-29 12:47     ` Miquel Raynal
2019-07-29 12:49       ` Michael Nazzareno Trimarchi
2019-07-29 12:55         ` Miquel Raynal
2019-07-29 13:00           ` Michael Nazzareno Trimarchi
2019-07-29 13:22             ` Miquel Raynal
2019-07-29 20:00               ` Michael Nazzareno Trimarchi
2019-07-29 21:02                 ` Miquel Raynal
2019-07-30  0:28       ` Greg Ungerer
2019-07-30  0:41         ` Greg Ungerer
2019-07-30  6:06           ` Greg Ungerer
2019-07-30  8:38             ` Miquel Raynal
2019-07-30  8:58               ` Boris Brezillon [this message]
2019-07-31  2:05               ` Greg Ungerer
2019-07-31  6:28                 ` Boris Brezillon
2019-08-02  7:19                   ` Greg Ungerer
2019-08-02 12:34                   ` Greg Ungerer
2019-08-02 12:51                     ` Boris Brezillon
2019-08-05  5:51                       ` Greg Ungerer
2019-08-07 16:05                         ` Miquel Raynal
2019-08-08  0:43                           ` Greg Ungerer
2019-08-08 16:36                         ` Boris Brezillon
2019-08-09  5:20                           ` Greg Ungerer
2019-08-09  6:23                             ` Boris Brezillon
2019-08-09  6:55                               ` Greg Ungerer
2019-08-09  7:32                                 ` Boris Brezillon
2019-08-09 13:57                                   ` Greg Ungerer
2019-08-09 13:59                                     ` Boris Brezillon
2019-08-12  2:50                                       ` Greg Ungerer
2019-08-12  4:04                                         ` Greg Ungerer
2019-08-12  7:31                                         ` Boris Brezillon
2019-08-13  0:50                                           ` Greg Ungerer
2021-01-28  9:45                                             ` Michael Nazzareno Trimarchi
2021-01-28 10:26                                               ` Miquel Raynal
2021-01-28 10:35                                                 ` Michael Nazzareno Trimarchi
2021-01-28 11:55                                                   ` Michael Nazzareno Trimarchi
2021-01-29 12:43                                               ` Greg Ungerer
2021-01-30  9:41                                                 ` Michael Nazzareno Trimarchi
2021-02-01 14:13                                                   ` Miquel Raynal
2021-02-01 14:32                                                     ` Michael Nazzareno Trimarchi
2021-02-01 15:08                                                       ` Michael Nazzareno Trimarchi
2021-02-01 15:14                                                         ` Miquel Raynal
2021-02-01 15:17                                                           ` Michael Nazzareno Trimarchi
2021-10-15 20:05                                                           ` Michael Trimarchi
2021-10-15 20:12                                                             ` Michael Nazzareno Trimarchi
2021-10-18  7:19                                                             ` Miquel Raynal
2021-10-18  7:33                                                               ` Michael Nazzareno Trimarchi
2021-10-18  7:43                                                                 ` Miquel Raynal
2021-10-04  5:54 ` Christian Eggers
2021-10-04  6:27   ` Michael Nazzareno Trimarchi
2021-10-04 15:33     ` Miquel Raynal
2021-10-04 16:06       ` Han Xu
2021-10-05  6:02         ` Christian Eggers
2021-10-08  9:55         ` Christian Eggers
2021-10-08 12:08           ` Stefan Riedmüller
2021-10-08 12:27             ` Miquel Raynal
2021-10-08 13:11               ` Christian Eggers
2021-10-08 13:29                 ` Miquel Raynal
2021-10-08 13:36                   ` Miquel Raynal
2021-10-08 13:49                     ` Christian Eggers
2021-10-08 16:07                       ` Miquel Raynal
2021-10-09  5:53                         ` Michael Nazzareno Trimarchi
2021-10-11  6:46                           ` Miquel Raynal
2021-10-12  9:02                             ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Stefan Riedmueller
2021-10-12  9:02                               ` [RFC PATCH 2/2] gpmi-nand: Add ERR007117 protection for nfc_apply_timings Stefan Riedmueller
2021-10-13  5:01                                 ` Han Xu
2021-10-22  8:45                                   ` Stefan Riedmüller
2021-10-22 14:35                                     ` han.xu
2021-10-25  9:39                                       ` Stefan Riedmüller
2021-10-28  9:28                                       ` Stefan Riedmüller
2021-11-01  4:01                                         ` han.xu
2021-10-13  6:10                                 ` Christian Eggers
2021-10-13  6:00                               ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Christian Eggers
2021-10-09  6:26                         ` GPMI iMX6ull timeout on DMA Christian Eggers
2021-10-13  6:15                           ` Christian Eggers
2021-10-08 13:13               ` Christian Eggers
2021-10-08 13:30                 ` Miquel Raynal
2021-10-09  6:33             ` Christian Eggers
  -- strict thread matches above, loose matches on Subject: below --
2018-10-02 13:22 GPMI IMX6ull timeout on dma Michael Nazzareno Trimarchi
2018-10-04 14:36 ` Michael Nazzareno Trimarchi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190730105843.1f587554@collabora.com \
    --to=boris.brezillon@collabora.com \
    --cc=bbrezillon@kernel.org \
    --cc=gerg@kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=michael@amarulasolutions.com \
    --cc=miquel.raynal@bootlin.com \
    --cc=s.hauer@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).