From: Pratyush Yadav <p.yadav@ti.com>
To: Tudor Ambarus <tudor.ambarus@microchip.com>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Mark Brown <broonie@kernel.org>,
Nicolas Ferre <nicolas.ferre@microchip.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Ludovic Desroches <ludovic.desroches@microchip.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Michal Simek <michal.simek@xilinx.com>,
<linux-mtd@lists.infradead.org>, <linux-kernel@vger.kernel.org>,
<linux-spi@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>
Cc: Boris Brezillon <boris.brezillon@collabora.com>,
Sekhar Nori <nsekhar@ti.com>, Pratyush Yadav <p.yadav@ti.com>
Subject: [PATCH v10 12/17] mtd: spi-nor: sfdp: detect Soft Reset sequence support from BFPT
Date: Wed, 24 Jun 2020 00:00:25 +0530 [thread overview]
Message-ID: <20200623183030.26591-13-p.yadav@ti.com> (raw)
In-Reply-To: <20200623183030.26591-1-p.yadav@ti.com>
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
drivers/mtd/spi-nor/core.h | 1 +
drivers/mtd/spi-nor/sfdp.c | 4 ++++
drivers/mtd/spi-nor/sfdp.h | 2 ++
3 files changed, 7 insertions(+)
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 6338d32a0d77..79ce952c0539 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -26,6 +26,7 @@ enum spi_nor_option_flags {
SNOR_F_HAS_SR_TB_BIT6 = BIT(11),
SNOR_F_HAS_4BIT_BP = BIT(12),
SNOR_F_HAS_SR_BP3_BIT6 = BIT(13),
+ SNOR_F_SOFT_RESET = BIT(14),
};
struct spi_nor_read_command {
diff --git a/drivers/mtd/spi-nor/sfdp.c b/drivers/mtd/spi-nor/sfdp.c
index 7983ff431346..8e0741d8bfd3 100644
--- a/drivers/mtd/spi-nor/sfdp.c
+++ b/drivers/mtd/spi-nor/sfdp.c
@@ -616,6 +616,10 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
break;
}
+ /* Soft Reset support. */
+ if (bfpt.dwords[BFPT_DWORD(16)] & BFPT_DWORD16_SOFT_RST)
+ nor->flags |= SNOR_F_SOFT_RESET;
+
/* Stop here if not JESD216 rev C or later. */
if (bfpt_header->length == BFPT_DWORD_MAX_JESD216B)
return spi_nor_post_bfpt_fixups(nor, bfpt_header, &bfpt,
diff --git a/drivers/mtd/spi-nor/sfdp.h b/drivers/mtd/spi-nor/sfdp.h
index 6d7243067252..8ae55e98084e 100644
--- a/drivers/mtd/spi-nor/sfdp.h
+++ b/drivers/mtd/spi-nor/sfdp.h
@@ -90,6 +90,8 @@ struct sfdp_bfpt {
#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD (0x4UL << 20)
#define BFPT_DWORD15_QER_SR2_BIT1 (0x5UL << 20) /* Spansion */
+#define BFPT_DWORD16_SOFT_RST BIT(12)
+
#define BFPT_DWORD18_CMD_EXT_MASK GENMASK(30, 29)
#define BFPT_DWORD18_CMD_EXT_REP (0x0UL << 29) /* Repeat */
#define BFPT_DWORD18_CMD_EXT_INV (0x1UL << 29) /* Invert */
--
2.27.0
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2020-06-23 18:38 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-23 18:30 [PATCH v10 00/17] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 01/17] spi: spi-mem: allow specifying whether an op is DTR or not Pratyush Yadav
2020-07-08 16:22 ` Tudor.Ambarus
2020-07-13 3:55 ` Tudor.Ambarus
2020-06-23 18:30 ` [PATCH v10 02/17] spi: spi-mem: allow specifying a command's extension Pratyush Yadav
2020-07-13 6:15 ` Tudor.Ambarus
2020-06-23 18:30 ` [PATCH v10 03/17] spi: atmel-quadspi: reject DTR ops Pratyush Yadav
2020-07-13 6:19 ` Tudor.Ambarus
2020-06-23 18:30 ` [PATCH v10 04/17] spi: spi-mtk-nor: " Pratyush Yadav
2020-07-13 6:24 ` Tudor.Ambarus
2020-06-23 18:30 ` [PATCH v10 05/17] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
2020-07-07 17:37 ` Tudor.Ambarus
2020-07-21 11:29 ` Pratyush Yadav
2020-09-29 15:42 ` Tudor.Ambarus
2020-09-29 16:29 ` Pratyush Yadav
2020-09-29 18:34 ` Tudor.Ambarus
2020-09-29 16:57 ` Vignesh Raghavendra
2020-06-23 18:30 ` [PATCH v10 06/17] mtd: spi-nor: sfdp: get command opcode extension type from BFPT Pratyush Yadav
2020-07-07 17:53 ` Tudor.Ambarus
2020-06-23 18:30 ` [PATCH v10 07/17] mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table Pratyush Yadav
2020-07-08 16:01 ` Tudor.Ambarus
2020-07-20 16:38 ` Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 08/17] mtd: spi-nor: core: use dummy cycle and address width info from SFDP Pratyush Yadav
2020-07-08 16:03 ` Tudor.Ambarus
2020-07-20 16:24 ` Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 09/17] mtd: spi-nor: core: do 2 byte reads for SR and FSR in DTR mode Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 10/17] mtd: spi-nor: core: enable octal DTR mode when possible Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 11/17] mtd: spi-nor: sfdp: do not make invalid quad enable fatal Pratyush Yadav
2020-07-13 9:33 ` Tudor.Ambarus
2020-06-23 18:30 ` Pratyush Yadav [this message]
2020-07-08 16:08 ` [PATCH v10 12/17] mtd: spi-nor: sfdp: detect Soft Reset sequence support from BFPT Tudor.Ambarus
2020-07-20 16:21 ` Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 13/17] mtd: spi-nor: core: perform a Soft Reset on shutdown Pratyush Yadav
2020-07-08 16:10 ` Tudor.Ambarus
2020-07-20 16:11 ` Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 14/17] mtd: spi-nor: core: disable Octal DTR mode on suspend Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 15/17] mtd: spi-nor: core: expose spi_nor_default_setup() in core.h Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 16/17] mtd: spi-nor: spansion: add support for Cypress Semper flash Pratyush Yadav
2020-06-23 18:30 ` [PATCH v10 17/17] mtd: spi-nor: micron-st: allow using MT35XU512ABA in Octal DTR mode Pratyush Yadav
2020-07-13 6:34 ` [PATCH v10 00/17] mtd: spi-nor: add xSPI Octal DTR support Tudor.Ambarus
2020-07-14 19:19 ` Mark Brown
2020-07-15 3:40 ` Tudor.Ambarus
2020-07-14 16:40 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200623183030.26591-13-p.yadav@ti.com \
--to=p.yadav@ti.com \
--cc=alexandre.belloni@bootlin.com \
--cc=boris.brezillon@collabora.com \
--cc=broonie@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=ludovic.desroches@microchip.com \
--cc=matthias.bgg@gmail.com \
--cc=michal.simek@xilinx.com \
--cc=miquel.raynal@bootlin.com \
--cc=nicolas.ferre@microchip.com \
--cc=nsekhar@ti.com \
--cc=richard@nod.at \
--cc=tudor.ambarus@microchip.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).