* [PATCH] mtd: spi-nor: Fixup page size for S25FS-S
@ 2020-01-14 13:47 Alexander X Sverdlin
2020-02-05 15:32 ` John Garry
0 siblings, 1 reply; 4+ messages in thread
From: Alexander X Sverdlin @ 2020-01-14 13:47 UTC (permalink / raw)
To: linux-mtd
Cc: Boris Brezillon, Richard Weinberger, Tudor Ambarus, stable,
Marek Vasut, Alexander Sverdlin, Brian Norris, David Woodhouse
From: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Spansion S25FS-S family has an issue in Basic Flash Parameter Table:
DWORD-11 bits 7-4 specify write page size 512 bytes. In reality this
is configurable in the non-volatile CR3NV register and even factory
default configuration is "wrap at 256 bytes". So blind relying on BFPT
breaks write operation on these Flashes.
All this story is vendor-specific, so add the corresponding fixup hook
which first restores the safe page size of 256 bytes from
struct flash_info but checks is more performant 512 bytes configuration
is active and adjusts the page_size accordingly.
Cc: stable@vger.kernel.org
Fixes: f384b352c ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
---
drivers/mtd/spi-nor/spi-nor.c | 39 +++++++++++++++++++++++++++++++++++++--
include/linux/mtd/spi-nor.h | 5 +++++
2 files changed, 42 insertions(+), 2 deletions(-)
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 73172d7..18f8705 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -1711,6 +1711,39 @@ static struct spi_nor_fixups mx25l25635_fixups = {
.post_bfpt = mx25l25635_post_bfpt_fixups,
};
+/* Spansion S25FS-S SFDP workarounds */
+static int s25fs_s_post_bfpt_fixups(struct spi_nor *nor,
+ const struct sfdp_parameter_header *bfpt_header,
+ const struct sfdp_bfpt *bfpt,
+ struct spi_nor_flash_parameter *params)
+{
+ const struct flash_info *info = nor->info;
+ u8 read_opcode, buf;
+ int ret;
+
+ /* Default is safe */
+ params->page_size = info->page_size;
+
+ /*
+ * But is the chip configured for more performant 512 bytes write page
+ * size?
+ */
+ read_opcode = nor->read_opcode;
+
+ nor->read_opcode = SPINOR_OP_RDAR;
+ ret = nor->read(nor, SPINOR_REG_CR3V, 1, &buf);
+ if (!ret && (buf & CR3V_02H_V))
+ params->page_size = 512;
+
+ nor->read_opcode = read_opcode;
+
+ return ret;
+}
+
+static const struct spi_nor_fixups s25fs_s_fixups = {
+ .post_bfpt = s25fs_s_post_bfpt_fixups,
+};
+
/* NOTE: double check command sets and memory organization when you add
* more nor chips. This current list focusses on newer chips, which
* have been converging on command sets which including JEDEC ID.
@@ -1903,7 +1936,8 @@ static const struct flash_info spi_nor_ids[] = {
SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
{ "s25fl128s1", INFO6(0x012018, 0x4d0180, 64 * 1024, 256,
SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
+ { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR)
+ .fixups = &s25fs_s_fixups, },
{ "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
{ "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256,
SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
@@ -1913,7 +1947,8 @@ static const struct flash_info spi_nor_ids[] = {
{ "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
{ "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
{ "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
+ { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR)
+ .fixups = &s25fs_s_fixups, },
{ "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) },
{ "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
{ "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index b3d360b..222eee9 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -114,6 +114,7 @@
/* Used for Spansion flashes only. */
#define SPINOR_OP_BRWR 0x17 /* Bank register write */
#define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */
+#define SPINOR_OP_RDAR 0x65 /* Read Any Register */
/* Used for Micron flashes only. */
#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
@@ -149,6 +150,10 @@
/* Status Register 2 bits. */
#define SR2_QUAD_EN_BIT7 BIT(7)
+/* Used for Spansion flashes RDAR command only. */
+#define SPINOR_REG_CR3V 0x800004
+#define CR3V_02H_V BIT(4) /* Page Buffer Wrap */
+
/* Supported SPI protocols */
#define SNOR_PROTO_INST_MASK GENMASK(23, 16)
#define SNOR_PROTO_INST_SHIFT 16
--
2.4.6
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH] mtd: spi-nor: Fixup page size for S25FS-S
2020-01-14 13:47 [PATCH] mtd: spi-nor: Fixup page size for S25FS-S Alexander X Sverdlin
@ 2020-02-05 15:32 ` John Garry
2020-02-05 16:03 ` Alexander Sverdlin
0 siblings, 1 reply; 4+ messages in thread
From: John Garry @ 2020-02-05 15:32 UTC (permalink / raw)
To: Alexander X Sverdlin, linux-mtd
Cc: Tudor Ambarus, Richard Weinberger, Boris Brezillon, stable,
Marek Vasut, Brian Norris, David Woodhouse
On 14/01/2020 13:47, Alexander X Sverdlin wrote:
> From: Alexander Sverdlin <alexander.sverdlin@nokia.com>
>
> Spansion S25FS-S family has an issue in Basic Flash Parameter Table:
> DWORD-11 bits 7-4 specify write page size 512 bytes. In reality this
> is configurable in the non-volatile CR3NV register and even factory
> default configuration is "wrap at 256 bytes". So blind relying on BFPT
> breaks write operation on these Flashes.
>
> All this story is vendor-specific, so add the corresponding fixup hook
> which first restores the safe page size of 256 bytes from
> struct flash_info but checks is more performant 512 bytes configuration
> is active and adjusts the page_size accordingly.
>
Hi Alexander,
One of my dev boards has part s25fl129p1, so I would like to try this
patch. However it does not apply. Any chance you could resend?
Thanks
John
> Cc: stable@vger.kernel.org
> Fixes: f384b352c ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
> ---
> drivers/mtd/spi-nor/spi-nor.c | 39 +++++++++++++++++++++++++++++++++++++--
> include/linux/mtd/spi-nor.h | 5 +++++
> 2 files changed, 42 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
> index 73172d7..18f8705 100644
> --- a/drivers/mtd/spi-nor/spi-nor.c
> +++ b/drivers/mtd/spi-nor/spi-nor.c
> @@ -1711,6 +1711,39 @@ static struct spi_nor_fixups mx25l25635_fixups = {
> .post_bfpt = mx25l25635_post_bfpt_fixups,
> };
>
> +/* Spansion S25FS-S SFDP workarounds */
> +static int s25fs_s_post_bfpt_fixups(struct spi_nor *nor,
> + const struct sfdp_parameter_header *bfpt_header,
> + const struct sfdp_bfpt *bfpt,
> + struct spi_nor_flash_parameter *params)
> +{
> + const struct flash_info *info = nor->info;
> + u8 read_opcode, buf;
> + int ret;
> +
> + /* Default is safe */
> + params->page_size = info->page_size;
> +
> + /*
> + * But is the chip configured for more performant 512 bytes write page
> + * size?
> + */
> + read_opcode = nor->read_opcode;
> +
> + nor->read_opcode = SPINOR_OP_RDAR;
> + ret = nor->read(nor, SPINOR_REG_CR3V, 1, &buf);
struct spi_nor has no member .read AFAICS.
> + if (!ret && (buf & CR3V_02H_V))
> + params->page_size = 512;
> +
> + nor->read_opcode = read_opcode;
> +
> + return ret;
> +}
> +
> +static const struct spi_nor_fixups s25fs_s_fixups = {
> + .post_bfpt = s25fs_s_post_bfpt_fixups,
> +};
> +
> /* NOTE: double check command sets and memory organization when you add
> * more nor chips. This current list focusses on newer chips, which
> * have been converging on command sets which including JEDEC ID.
> @@ -1903,7 +1936,8 @@ static const struct flash_info spi_nor_ids[] = {
> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> { "s25fl128s1", INFO6(0x012018, 0x4d0180, 64 * 1024, 256,
> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> - { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
> + { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR)
> + .fixups = &s25fs_s_fixups, },
> { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> { "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256,
> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
> @@ -1913,7 +1947,8 @@ static const struct flash_info spi_nor_ids[] = {
> { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
> { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
> { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> - { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
> + { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR)
> + .fixups = &s25fs_s_fixups, },
> { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) },
> { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
> { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
> diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
> index b3d360b..222eee9 100644
> --- a/include/linux/mtd/spi-nor.h
> +++ b/include/linux/mtd/spi-nor.h
> @@ -114,6 +114,7 @@
> /* Used for Spansion flashes only. */
> #define SPINOR_OP_BRWR 0x17 /* Bank register write */
> #define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */
> +#define SPINOR_OP_RDAR 0x65 /* Read Any Register */
>
> /* Used for Micron flashes only. */
> #define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
> @@ -149,6 +150,10 @@
> /* Status Register 2 bits. */
> #define SR2_QUAD_EN_BIT7 BIT(7)
>
> +/* Used for Spansion flashes RDAR command only. */
> +#define SPINOR_REG_CR3V 0x800004
> +#define CR3V_02H_V BIT(4) /* Page Buffer Wrap */
> +
> /* Supported SPI protocols */
> #define SNOR_PROTO_INST_MASK GENMASK(23, 16)
> #define SNOR_PROTO_INST_SHIFT 16
>
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH] mtd: spi-nor: Fixup page size for S25FS-S
2020-02-05 15:32 ` John Garry
@ 2020-02-05 16:03 ` Alexander Sverdlin
2020-02-05 16:17 ` John Garry
0 siblings, 1 reply; 4+ messages in thread
From: Alexander Sverdlin @ 2020-02-05 16:03 UTC (permalink / raw)
To: John Garry, linux-mtd
Cc: Tudor Ambarus, Richard Weinberger, Boris Brezillon, stable,
Marek Vasut, Brian Norris, David Woodhouse
Hello!
On 05/02/2020 16:32, John Garry wrote:
> On 14/01/2020 13:47, Alexander X Sverdlin wrote:
>> From: Alexander Sverdlin <alexander.sverdlin@nokia.com>
>>
>> Spansion S25FS-S family has an issue in Basic Flash Parameter Table:
>> DWORD-11 bits 7-4 specify write page size 512 bytes. In reality this
>> is configurable in the non-volatile CR3NV register and even factory
>> default configuration is "wrap at 256 bytes". So blind relying on BFPT
>> breaks write operation on these Flashes.
>>
>> All this story is vendor-specific, so add the corresponding fixup hook
>> which first restores the safe page size of 256 bytes from
>> struct flash_info but checks is more performant 512 bytes configuration
>> is active and adjusts the page_size accordingly.
[...]
> One of my dev boards has part s25fl129p1, so I would like to try this patch. However it does not apply. Any chance you could resend?
It was based on spi-nor/next branch of git://git.infradead.org/l2-mtd.git and as I can
see, this branch is unchanged from the last patch submission.
I can re-send if one of the maintainers confirms this wasn't the correct branch
to base on.
[...]
>> Cc: stable@vger.kernel.org
>> Fixes: f384b352c ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
>> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
>> ---
>> drivers/mtd/spi-nor/spi-nor.c | 39 +++++++++++++++++++++++++++++++++++++--
>> include/linux/mtd/spi-nor.h | 5 +++++
>> 2 files changed, 42 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
>> index 73172d7..18f8705 100644
>> --- a/drivers/mtd/spi-nor/spi-nor.c
>> +++ b/drivers/mtd/spi-nor/spi-nor.c
>> @@ -1711,6 +1711,39 @@ static struct spi_nor_fixups mx25l25635_fixups = {
>> .post_bfpt = mx25l25635_post_bfpt_fixups,
>> };
>> +/* Spansion S25FS-S SFDP workarounds */
>> +static int s25fs_s_post_bfpt_fixups(struct spi_nor *nor,
>> + const struct sfdp_parameter_header *bfpt_header,
>> + const struct sfdp_bfpt *bfpt,
>> + struct spi_nor_flash_parameter *params)
>> +{
>> + const struct flash_info *info = nor->info;
>> + u8 read_opcode, buf;
>> + int ret;
>> +
>> + /* Default is safe */
>> + params->page_size = info->page_size;
>> +
>> + /*
>> + * But is the chip configured for more performant 512 bytes write page
>> + * size?
>> + */
>> + read_opcode = nor->read_opcode;
>> +
>> + nor->read_opcode = SPINOR_OP_RDAR;
>> + ret = nor->read(nor, SPINOR_REG_CR3V, 1, &buf);
>
> struct spi_nor has no member .read AFAICS.
>
>> + if (!ret && (buf & CR3V_02H_V))
>> + params->page_size = 512;
>> +
>> + nor->read_opcode = read_opcode;
>> +
>> + return ret;
>> +}
>> +
>> +static const struct spi_nor_fixups s25fs_s_fixups = {
>> + .post_bfpt = s25fs_s_post_bfpt_fixups,
>> +};
>> +
>> /* NOTE: double check command sets and memory organization when you add
>> * more nor chips. This current list focusses on newer chips, which
>> * have been converging on command sets which including JEDEC ID.
>> @@ -1903,7 +1936,8 @@ static const struct flash_info spi_nor_ids[] = {
>> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>> { "s25fl128s1", INFO6(0x012018, 0x4d0180, 64 * 1024, 256,
>> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>> - { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
>> + { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR)
>> + .fixups = &s25fs_s_fixups, },
>> { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>> { "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256,
>> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
>> @@ -1913,7 +1947,8 @@ static const struct flash_info spi_nor_ids[] = {
>> { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
>> { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
>> { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>> - { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>> + { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR)
>> + .fixups = &s25fs_s_fixups, },
>> { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) },
>> { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
>> { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
>> diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
>> index b3d360b..222eee9 100644
>> --- a/include/linux/mtd/spi-nor.h
>> +++ b/include/linux/mtd/spi-nor.h
>> @@ -114,6 +114,7 @@
>> /* Used for Spansion flashes only. */
>> #define SPINOR_OP_BRWR 0x17 /* Bank register write */
>> #define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */
>> +#define SPINOR_OP_RDAR 0x65 /* Read Any Register */
>> /* Used for Micron flashes only. */
>> #define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
>> @@ -149,6 +150,10 @@
>> /* Status Register 2 bits. */
>> #define SR2_QUAD_EN_BIT7 BIT(7)
>> +/* Used for Spansion flashes RDAR command only. */
>> +#define SPINOR_REG_CR3V 0x800004
>> +#define CR3V_02H_V BIT(4) /* Page Buffer Wrap */
>> +
>> /* Supported SPI protocols */
>> #define SNOR_PROTO_INST_MASK GENMASK(23, 16)
>> #define SNOR_PROTO_INST_SHIFT 16
>>
>
>
--
Best regards,
Alexander Sverdlin.
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH] mtd: spi-nor: Fixup page size for S25FS-S
2020-02-05 16:03 ` Alexander Sverdlin
@ 2020-02-05 16:17 ` John Garry
0 siblings, 0 replies; 4+ messages in thread
From: John Garry @ 2020-02-05 16:17 UTC (permalink / raw)
To: Alexander Sverdlin, linux-mtd
Cc: Boris Brezillon, Richard Weinberger, Tudor Ambarus, stable,
Marek Vasut, Brian Norris, David Woodhouse
On 05/02/2020 16:03, Alexander Sverdlin wrote:
> Hello!
>
> On 05/02/2020 16:32, John Garry wrote:
>> On 14/01/2020 13:47, Alexander X Sverdlin wrote:
>>> From: Alexander Sverdlin <alexander.sverdlin@nokia.com>
>>>
>>> Spansion S25FS-S family has an issue in Basic Flash Parameter Table:
>>> DWORD-11 bits 7-4 specify write page size 512 bytes. In reality this
>>> is configurable in the non-volatile CR3NV register and even factory
>>> default configuration is "wrap at 256 bytes". So blind relying on BFPT
>>> breaks write operation on these Flashes.
>>>
>>> All this story is vendor-specific, so add the corresponding fixup hook
>>> which first restores the safe page size of 256 bytes from
>>> struct flash_info but checks is more performant 512 bytes configuration
>>> is active and adjusts the page_size accordingly.
>
> [...]
>
>> One of my dev boards has part s25fl129p1, so I would like to try this patch. However it does not apply. Any chance you could resend?
>
Actually I was testing against linux-next, which I assumed included the
Maintainers dev tree.
> It was based on spi-nor/next branch of git://git.infradead.org/l2-mtd.git and as I can
> see,
From a quick check, that branch does not seem to have seen anything new
since March 2019.
this branch is unchanged from the last patch submission.
According to the MAINTAINERS file, we have:
SPI NOR SUBSYSTEM
M: Tudor Ambarus <tudor.ambarus@microchip.com>
L: linux-mtd@lists.infradead.org
W: http://www.linux-mtd.infradead.org/
Q: http://patchwork.ozlabs.org/project/linux-mtd/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git
spi-nor/next
S: Maintained
F: drivers/mtd/spi-nor/
F: include/linux/mtd/spi-nor.h
Last patch on the spi-nor/next branch is 16th Jan, 2020.
Cheers,
John
> I can re-send if one of the maintainers confirms this wasn't the correct branch
> to base on.
>
> [...]
>
>>> Cc: stable@vger.kernel.org
>>> Fixes: f384b352c ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
>>> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
>>> ---
>>> drivers/mtd/spi-nor/spi-nor.c | 39 +++++++++++++++++++++++++++++++++++++--
>>> include/linux/mtd/spi-nor.h | 5 +++++
>>> 2 files changed, 42 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
>>> index 73172d7..18f8705 100644
>>> --- a/drivers/mtd/spi-nor/spi-nor.c
>>> +++ b/drivers/mtd/spi-nor/spi-nor.c
>>> @@ -1711,6 +1711,39 @@ static struct spi_nor_fixups mx25l25635_fixups = {
>>> .post_bfpt = mx25l25635_post_bfpt_fixups,
>>> };
>>> +/* Spansion S25FS-S SFDP workarounds */
>>> +static int s25fs_s_post_bfpt_fixups(struct spi_nor *nor,
>>> + const struct sfdp_parameter_header *bfpt_header,
>>> + const struct sfdp_bfpt *bfpt,
>>> + struct spi_nor_flash_parameter *params)
>>> +{
>>> + const struct flash_info *info = nor->info;
>>> + u8 read_opcode, buf;
>>> + int ret;
>>> +
>>> + /* Default is safe */
>>> + params->page_size = info->page_size;
>>> +
>>> + /*
>>> + * But is the chip configured for more performant 512 bytes write page
>>> + * size?
>>> + */
>>> + read_opcode = nor->read_opcode;
>>> +
>>> + nor->read_opcode = SPINOR_OP_RDAR;
>>> + ret = nor->read(nor, SPINOR_REG_CR3V, 1, &buf);
>>
>> struct spi_nor has no member .read AFAICS.
>>
>>> + if (!ret && (buf & CR3V_02H_V))
>>> + params->page_size = 512;
>>> +
>>> + nor->read_opcode = read_opcode;
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static const struct spi_nor_fixups s25fs_s_fixups = {
>>> + .post_bfpt = s25fs_s_post_bfpt_fixups,
>>> +};
>>> +
>>> /* NOTE: double check command sets and memory organization when you add
>>> * more nor chips. This current list focusses on newer chips, which
>>> * have been converging on command sets which including JEDEC ID.
>>> @@ -1903,7 +1936,8 @@ static const struct flash_info spi_nor_ids[] = {
>>> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>>> { "s25fl128s1", INFO6(0x012018, 0x4d0180, 64 * 1024, 256,
>>> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>>> - { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
>>> + { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR)
>>> + .fixups = &s25fs_s_fixups, },
>>> { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>>> { "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256,
>>> SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
>>> @@ -1913,7 +1947,8 @@ static const struct flash_info spi_nor_ids[] = {
>>> { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
>>> { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
>>> { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>>> - { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
>>> + { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR)
>>> + .fixups = &s25fs_s_fixups, },
>>> { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) },
>>> { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
>>> { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
>>> diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
>>> index b3d360b..222eee9 100644
>>> --- a/include/linux/mtd/spi-nor.h
>>> +++ b/include/linux/mtd/spi-nor.h
>>> @@ -114,6 +114,7 @@
>>> /* Used for Spansion flashes only. */
>>> #define SPINOR_OP_BRWR 0x17 /* Bank register write */
>>> #define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */
>>> +#define SPINOR_OP_RDAR 0x65 /* Read Any Register */
>>> /* Used for Micron flashes only. */
>>> #define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
>>> @@ -149,6 +150,10 @@
>>> /* Status Register 2 bits. */
>>> #define SR2_QUAD_EN_BIT7 BIT(7)
>>> +/* Used for Spansion flashes RDAR command only. */
>>> +#define SPINOR_REG_CR3V 0x800004
>>> +#define CR3V_02H_V BIT(4) /* Page Buffer Wrap */
>>> +
>>> /* Supported SPI protocols */
>>> #define SNOR_PROTO_INST_MASK GENMASK(23, 16)
>>> #define SNOR_PROTO_INST_SHIFT 16
>>>
>>
>>
>
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-02-05 16:18 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-01-14 13:47 [PATCH] mtd: spi-nor: Fixup page size for S25FS-S Alexander X Sverdlin
2020-02-05 15:32 ` John Garry
2020-02-05 16:03 ` Alexander Sverdlin
2020-02-05 16:17 ` John Garry
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).