From: Michael Walle <michael@walle.cc>
To: Pratyush Yadav <p.yadav@ti.com>
Cc: Tudor.Ambarus@microchip.com, nm@ti.com, kristo@kernel.org,
robh+dt@kernel.org, miquel.raynal@bootlin.com, richard@nod.at,
vigneshr@ti.com, broonie@kernel.org,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-mtd@lists.infradead.org,
linux-spi@vger.kernel.org, lokeshvutla@ti.com
Subject: Re: [RFC PATCH 0/6] spi: Add OSPI PHY calibration support for spi-cadence-quadspi
Date: Fri, 12 Mar 2021 11:20:15 +0100 [thread overview]
Message-ID: <676386736df5e5b22e34b0b5af91c894@walle.cc> (raw)
In-Reply-To: <20210312101036.jfz2733ssv4nhfey@ti.com>
Am 2021-03-12 11:10, schrieb Pratyush Yadav:
> There is usually a delay from when the flash drives the data line (IOW,
> puts a data bit on it) and when the signal reaches the controller. This
> delay can vary by the flash, board, silicon characteristics,
> temperature, etc.
Temperature might change over time, but the calibration is only done
once. I don't know how much influence the temperature actually has, but
our boards are usually operating from -40°C to +85°C. So there might be
a possible temperature difference of 125K between actual calibration and
when the flash is accessed.
-michael
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2021-03-12 10:21 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-11 19:12 [RFC PATCH 0/6] spi: Add OSPI PHY calibration support for spi-cadence-quadspi Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 1/6] spi: spi-mem: Tell controller when device is ready for calibration Pratyush Yadav
2021-03-23 23:07 ` Michael Walle
2021-03-24 8:08 ` Pratyush Yadav
2021-04-29 16:23 ` Michael Walle
2021-04-29 18:41 ` Pratyush Yadav
2021-04-29 22:46 ` Michael Walle
2021-03-11 19:12 ` [RFC PATCH 2/6] mtd: spi-nor: core: consolidate read op creation Pratyush Yadav
2021-03-23 23:17 ` Michael Walle
2021-03-24 8:04 ` Pratyush Yadav
2021-04-08 12:48 ` Michael Walle
2021-03-11 19:12 ` [RFC PATCH 3/6] mtd: spi-nor: core: run calibration when initialization is done Pratyush Yadav
2022-05-17 14:02 ` Miquel Raynal
2022-05-18 6:07 ` Pratyush Yadav
2022-05-18 7:19 ` Miquel Raynal
2022-05-18 7:56 ` Pratyush Yadav
2022-05-18 8:51 ` Cédric Le Goater
2022-06-27 9:14 ` Pratyush Yadav
2022-06-27 9:43 ` Cédric Le Goater
2022-06-27 10:35 ` Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 4/6] spi: cadence-qspi: Use PHY for DAC reads if possible Pratyush Yadav
2021-03-12 9:13 ` Tudor.Ambarus
2021-03-12 10:17 ` Pratyush Yadav
2021-04-29 16:28 ` Michael Walle
2021-04-29 18:19 ` Pratyush Yadav
2021-04-29 22:20 ` Michael Walle
2021-05-10 11:39 ` Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 5/6] spi: cadence-qspi: Tune PHY to allow running at higher frequencies Pratyush Yadav
2021-04-29 22:48 ` Michael Walle
2021-04-30 5:42 ` Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 6/6] arm64: dts: ti: k3-j721e-som-p0: Enable PHY calibration Pratyush Yadav
2021-03-12 9:09 ` [RFC PATCH 0/6] spi: Add OSPI PHY calibration support for spi-cadence-quadspi Tudor.Ambarus
2021-03-12 10:10 ` Pratyush Yadav
2021-03-12 10:20 ` Michael Walle [this message]
2021-03-12 11:07 ` Pratyush Yadav
2021-03-12 13:26 ` Michael Walle
2021-03-12 11:23 ` Tudor.Ambarus
2021-03-12 18:14 ` Pratyush Yadav
2021-03-12 13:32 ` Michael Walle
2021-03-12 14:59 ` Tudor.Ambarus
2021-03-12 17:00 ` Pratyush Yadav
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=676386736df5e5b22e34b0b5af91c894@walle.cc \
--to=michael@walle.cc \
--cc=Tudor.Ambarus@microchip.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=miquel.raynal@bootlin.com \
--cc=nm@ti.com \
--cc=p.yadav@ti.com \
--cc=richard@nod.at \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).