Linux-mtd Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
@ 2020-05-20 10:21 Robert Jarzmik
  2020-05-20 10:21 ` [PATCH v2 2/3] MAINTAINERS: pxa: remove Compulab arm/pxa support Robert Jarzmik
                   ` (2 more replies)
  0 siblings, 3 replies; 15+ messages in thread
From: Robert Jarzmik @ 2020-05-20 10:21 UTC (permalink / raw)
  To: Arnd Bergmann, Miquel Raynal, Boris Brezillon, Mike Rapoport
  Cc: Robert Jarzmik, linux-mtd, linux-arm-kernel

As these boards have no more users nor testers, and patching them has
become a burden, be that because of the PCI part or the MTD NAND
support, let's remove them.

The cm-x300 will for now remain and represent Compulab boards at its
best in the PXA department.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
---
Since v1: Arnd's comments
---
 arch/arm/configs/cm_x2xx_defconfig  |  173 ----
 arch/arm/configs/em_x270_defconfig  |  178 ----
 arch/arm/configs/pxa_defconfig      |    2 -
 arch/arm/mach-pxa/Kconfig           |   17 -
 arch/arm/mach-pxa/Makefile          |    5 -
 arch/arm/mach-pxa/cm-x255.c         |  240 -----
 arch/arm/mach-pxa/cm-x270.c         |  419 ---------
 arch/arm/mach-pxa/cm-x2xx-pci.c     |  196 ----
 arch/arm/mach-pxa/cm-x2xx-pci.h     |   14 -
 arch/arm/mach-pxa/cm-x2xx.c         |  538 -----------
 arch/arm/mach-pxa/em-x270.c         | 1286 ---------------------------
 arch/arm/mach-pxa/include/mach/io.h |   18 -
 12 files changed, 3086 deletions(-)
 delete mode 100644 arch/arm/configs/cm_x2xx_defconfig
 delete mode 100644 arch/arm/configs/em_x270_defconfig
 delete mode 100644 arch/arm/mach-pxa/cm-x255.c
 delete mode 100644 arch/arm/mach-pxa/cm-x270.c
 delete mode 100644 arch/arm/mach-pxa/cm-x2xx-pci.c
 delete mode 100644 arch/arm/mach-pxa/cm-x2xx-pci.h
 delete mode 100644 arch/arm/mach-pxa/cm-x2xx.c
 delete mode 100644 arch/arm/mach-pxa/em-x270.c
 delete mode 100644 arch/arm/mach-pxa/include/mach/io.h

diff --git a/arch/arm/configs/cm_x2xx_defconfig b/arch/arm/configs/cm_x2xx_defconfig
deleted file mode 100644
index fa997ae2673e..000000000000
--- a/arch/arm/configs/cm_x2xx_defconfig
+++ /dev/null
@@ -1,173 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_PXA=y
-CONFIG_MACH_ARMCORE=y
-CONFIG_PCI=y
-CONFIG_PCCARD=m
-CONFIG_YENTA=m
-# CONFIG_YENTA_O2 is not set
-# CONFIG_YENTA_RICOH is not set
-# CONFIG_YENTA_ENE_TUNE is not set
-# CONFIG_YENTA_TOSHIBA is not set
-CONFIG_PCMCIA_PXA2XX=m
-CONFIG_NO_HZ=y
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=1f03 mem=32M"
-CONFIG_FPE_NWFPE=y
-CONFIG_PM=y
-CONFIG_APM_EMULATION=m
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_BT=m
-CONFIG_BT_RFCOMM=m
-CONFIG_BT_BNEP=m
-CONFIG_BT_HIDP=m
-CONFIG_LIB80211=m
-CONFIG_FW_LOADER=m
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PXA2XX=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MTD_NAND_GPIO=m
-CONFIG_MTD_NAND_CM_X270=y
-CONFIG_MTD_NAND_PLATFORM=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_ATA=m
-# CONFIG_SATA_PMP is not set
-CONFIG_PATA_PCMCIA=m
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_DM9000=y
-CONFIG_DM9000_DEBUGLEVEL=1
-CONFIG_NET_PCI=y
-CONFIG_8139TOO=m
-# CONFIG_8139TOO_PIO is not set
-CONFIG_PPP=m
-CONFIG_PPP_MULTILINK=y
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_INPUT_EVDEV=y
-CONFIG_KEYBOARD_PXA27x=m
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_UCB1400=m
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=16
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=m
-CONFIG_I2C_PXA=y
-CONFIG_SPI=y
-CONFIG_SPI_PXA2XX=m
-# CONFIG_HWMON is not set
-CONFIG_UCB1400_CORE=m
-CONFIG_FB=y
-CONFIG_FB_PXA=y
-CONFIG_FB_PXA_PARAMETERS=y
-CONFIG_FB_MBX=m
-# CONFIG_LCD_CLASS_DEVICE is not set
-# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-CONFIG_SOUND=m
-CONFIG_SND=m
-CONFIG_SND_MIXER_OSS=m
-CONFIG_SND_PCM_OSS=m
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_PCI is not set
-CONFIG_SND_PXA2XX_AC97=m
-# CONFIG_SND_SPI is not set
-# CONFIG_SND_USB is not set
-# CONFIG_SND_PCMCIA is not set
-CONFIG_HID_A4TECH=y
-CONFIG_HID_APPLE=y
-CONFIG_HID_BELKIN=y
-CONFIG_HID_CHERRY=y
-CONFIG_HID_CHICONY=y
-CONFIG_HID_CYPRESS=y
-CONFIG_HID_EZKEY=y
-CONFIG_HID_GYRATION=y
-CONFIG_HID_LOGITECH=y
-CONFIG_HID_MICROSOFT=y
-CONFIG_HID_MONTEREY=y
-CONFIG_HID_PANTHERLORD=y
-CONFIG_HID_PETALYNX=y
-CONFIG_HID_SAMSUNG=y
-CONFIG_HID_SONY=y
-CONFIG_HID_SUNPLUS=y
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_MMC=m
-CONFIG_MMC_PXA=m
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=m
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_V3020=y
-CONFIG_RTC_DRV_PXA=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_VFAT_FS=m
-# CONFIG_PROC_PAGE_MONITOR is not set
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_CIFS=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_NLS_UTF8=m
-CONFIG_FRAME_WARN=0
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DETECT_SOFTLOCKUP is not set
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
diff --git a/arch/arm/configs/em_x270_defconfig b/arch/arm/configs/em_x270_defconfig
deleted file mode 100644
index d08f02014755..000000000000
--- a/arch/arm/configs/em_x270_defconfig
+++ /dev/null
@@ -1,178 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_PXA=y
-CONFIG_MACH_EM_X270=y
-CONFIG_MACH_EXEDA=y
-CONFIG_NO_HZ=y
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=1f03 mem=32M"
-CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_GOV_USERSPACE=m
-CONFIG_FPE_NWFPE=y
-CONFIG_PM=y
-CONFIG_APM_EMULATION=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_BT=m
-CONFIG_BT_RFCOMM=m
-CONFIG_BT_BNEP=m
-CONFIG_BT_HIDP=m
-CONFIG_BT_HCIBTUSB=m
-CONFIG_LIB80211=m
-CONFIG_FW_LOADER=m
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PXA2XX=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MTD_NAND_PLATFORM=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-# CONFIG_SCSI_LOWLEVEL is not set
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_DM9000=y
-CONFIG_DM9000_DEBUGLEVEL=1
-CONFIG_PPP=m
-CONFIG_PPP_MULTILINK=y
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_INPUT_EVDEV=y
-CONFIG_INPUT_APMPOWER=y
-CONFIG_KEYBOARD_GPIO=y
-CONFIG_KEYBOARD_PXA27x=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-# CONFIG_TOUCHSCREEN_DA9034 is not set
-CONFIG_TOUCHSCREEN_WM97XX=m
-# CONFIG_TOUCHSCREEN_WM9705 is not set
-# CONFIG_TOUCHSCREEN_WM9713 is not set
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=16
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=m
-CONFIG_I2C_PXA=y
-CONFIG_SPI=y
-CONFIG_SPI_PXA2XX=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_BATTERY_DA9030=y
-# CONFIG_HWMON is not set
-CONFIG_PMIC_DA903X=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_DA903X=y
-CONFIG_FB=y
-CONFIG_FB_PXA=y
-CONFIG_FB_PXA_PARAMETERS=y
-CONFIG_FB_MBX=m
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_LCD_TDO24M=y
-# CONFIG_BACKLIGHT_GENERIC is not set
-CONFIG_BACKLIGHT_DA903X=m
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-CONFIG_SOUND=m
-CONFIG_SND=m
-CONFIG_SND_MIXER_OSS=m
-CONFIG_SND_PCM_OSS=m
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_SPI is not set
-# CONFIG_SND_USB is not set
-CONFIG_SND_SOC=m
-CONFIG_SND_PXA2XX_SOC=m
-CONFIG_SND_PXA2XX_SOC_EM_X270=m
-CONFIG_HID_A4TECH=y
-CONFIG_HID_APPLE=y
-CONFIG_HID_BELKIN=y
-CONFIG_HID_CHERRY=y
-CONFIG_HID_CHICONY=y
-CONFIG_HID_CYPRESS=y
-CONFIG_HID_EZKEY=y
-CONFIG_HID_GYRATION=y
-CONFIG_HID_LOGITECH=y
-CONFIG_HID_MICROSOFT=y
-CONFIG_HID_MONTEREY=y
-CONFIG_HID_PANTHERLORD=y
-CONFIG_HID_PETALYNX=y
-CONFIG_HID_SAMSUNG=y
-CONFIG_HID_SONY=y
-CONFIG_HID_SUNPLUS=y
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_MMC=m
-CONFIG_MMC_PXA=m
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_DA903X=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_V3020=y
-CONFIG_RTC_DRV_PXA=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_VFAT_FS=m
-# CONFIG_PROC_PAGE_MONITOR is not set
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_CIFS=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_NLS_UTF8=m
-CONFIG_FRAME_WARN=0
-CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DETECT_SOFTLOCKUP is not set
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_MICHAEL_MIC=m
-CONFIG_CRYPTO_AES=m
-CONFIG_CRYPTO_ARC4=m
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
diff --git a/arch/arm/configs/pxa_defconfig b/arch/arm/configs/pxa_defconfig
index b817c57f05f1..e6559e3350e6 100644
--- a/arch/arm/configs/pxa_defconfig
+++ b/arch/arm/configs/pxa_defconfig
@@ -38,8 +38,6 @@ CONFIG_MACH_ARCOM_ZEUS=y
 CONFIG_MACH_BALLOON3=y
 CONFIG_MACH_CSB726=y
 CONFIG_CSB726_CSB701=y
-CONFIG_MACH_ARMCORE=y
-CONFIG_MACH_EM_X270=y
 CONFIG_MACH_EXEDA=y
 CONFIG_MACH_CM_X300=y
 CONFIG_MACH_CAPC7117=y
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index f60bc29aef68..f7520a6cc7d4 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -123,23 +123,6 @@ config CSB726_CSB701
 	bool "Enable support for CSB701 baseboard"
 	depends on MACH_CSB726
 
-config MACH_ARMCORE
-	bool "CompuLab CM-X255/CM-X270 modules"
-	select ARCH_HAS_DMA_SET_COHERENT_MASK if PCI
-	select IWMMXT
-	select HAVE_PCI
-	select NEED_MACH_IO_H if PCI
-	select PXA25x
-	select PXA27x
-
-config MACH_EM_X270
-	bool "CompuLab EM-x270 platform"
-	select PXA27x
-
-config MACH_EXEDA
-	bool "CompuLab eXeda platform"
-	select PXA27x
-
 config MACH_CM_X300
 	bool "CompuLab CM-X300 modules"
 	select CPU_PXA300
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index f70728930c4f..177abe584dd5 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -40,11 +40,6 @@ obj-$(CONFIG_MACH_ARCOM_ZEUS)	+= zeus.o
 obj-$(CONFIG_MACH_BALLOON3)	+= balloon3.o
 obj-$(CONFIG_MACH_CSB726)	+= csb726.o
 obj-$(CONFIG_CSB726_CSB701)	+= csb701.o
-obj-$(CONFIG_MACH_ARMCORE)      += cm-x2xx.o cm-x255.o cm-x270.o
-ifeq ($(CONFIG_PCI),y)
-obj-$(CONFIG_MACH_ARMCORE)	+= cm-x2xx-pci.o
-endif
-obj-$(CONFIG_MACH_EM_X270)	+= em-x270.o
 obj-$(CONFIG_MACH_CM_X300)      += cm-x300.o
 obj-$(CONFIG_MACH_CAPC7117)     += capc7117.o mxm8x10.o
 obj-$(CONFIG_ARCH_GUMSTIX)	+= gumstix.o
diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c
deleted file mode 100644
index ea1e85775759..000000000000
--- a/arch/arm/mach-pxa/cm-x255.c
+++ /dev/null
@@ -1,240 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-pxa/cm-x255.c
- *
- * Copyright (C) 2007, 2008 CompuLab, Ltd.
- * Mike Rapoport <mike@compulab.co.il>
- */
-
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/nand-gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/pxa2xx_spi.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <asm/mach/map.h>
-
-#include "pxa25x.h"
-
-#include "generic.h"
-
-#define GPIO_NAND_CS	(5)
-#define GPIO_NAND_ALE	(4)
-#define GPIO_NAND_CLE	(3)
-#define GPIO_NAND_RB	(10)
-
-static unsigned long cmx255_pin_config[] = {
-	/* AC'97 */
-	GPIO28_AC97_BITCLK,
-	GPIO29_AC97_SDATA_IN_0,
-	GPIO30_AC97_SDATA_OUT,
-	GPIO31_AC97_SYNC,
-
-	/* BTUART */
-	GPIO42_BTUART_RXD,
-	GPIO43_BTUART_TXD,
-	GPIO44_BTUART_CTS,
-	GPIO45_BTUART_RTS,
-
-	/* STUART */
-	GPIO46_STUART_RXD,
-	GPIO47_STUART_TXD,
-
-	/* LCD */
-	GPIOxx_LCD_TFT_16BPP,
-
-	/* SSP1 */
-	GPIO23_SSP1_SCLK,
-	GPIO24_SSP1_SFRM,
-	GPIO25_SSP1_TXD,
-	GPIO26_SSP1_RXD,
-
-	/* SSP2 */
-	GPIO81_SSP2_CLK_OUT,
-	GPIO82_SSP2_FRM_OUT,
-	GPIO83_SSP2_TXD,
-	GPIO84_SSP2_RXD,
-
-	/* PC Card */
-	GPIO48_nPOE,
-	GPIO49_nPWE,
-	GPIO50_nPIOR,
-	GPIO51_nPIOW,
-	GPIO52_nPCE_1,
-	GPIO53_nPCE_2,
-	GPIO54_nPSKTSEL,
-	GPIO55_nPREG,
-	GPIO56_nPWAIT,
-	GPIO57_nIOIS16,
-
-	/* SDRAM and local bus */
-	GPIO15_nCS_1,
-	GPIO78_nCS_2,
-	GPIO79_nCS_3,
-	GPIO80_nCS_4,
-	GPIO33_nCS_5,
-	GPIO18_RDY,
-
-	/* GPIO */
-	GPIO0_GPIO	| WAKEUP_ON_EDGE_BOTH,
-	GPIO9_GPIO,				/* PC card reset */
-
-	/* NAND controls */
-	GPIO5_GPIO	| MFP_LPM_DRIVE_HIGH,	/* NAND CE# */
-	GPIO4_GPIO	| MFP_LPM_DRIVE_LOW,	/* NAND ALE */
-	GPIO3_GPIO	| MFP_LPM_DRIVE_LOW,	/* NAND CLE */
-	GPIO10_GPIO,				/* NAND Ready/Busy */
-
-	/* interrupts */
-	GPIO22_GPIO,	/* DM9000 interrupt */
-};
-
-#if defined(CONFIG_SPI_PXA2XX)
-static struct pxa2xx_spi_controller pxa_ssp_master_info = {
-	.num_chipselect	= 1,
-};
-
-static struct spi_board_info spi_board_info[] __initdata = {
-	[0] = {
-		.modalias	= "rtc-max6902",
-		.max_speed_hz	= 1000000,
-		.bus_num	= 1,
-		.chip_select	= 0,
-	},
-};
-
-static void __init cmx255_init_rtc(void)
-{
-	pxa2xx_set_spi_info(1, &pxa_ssp_master_info);
-	spi_register_board_info(ARRAY_AND_SIZE(spi_board_info));
-}
-#else
-static inline void cmx255_init_rtc(void) {}
-#endif
-
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
-static struct mtd_partition cmx255_nor_partitions[] = {
-	{
-		.name		= "ARMmon",
-		.size		= 0x00030000,
-		.offset		= 0,
-		.mask_flags	= MTD_WRITEABLE  /* force read-only */
-	} , {
-		.name		= "ARMmon setup block",
-		.size		= 0x00010000,
-		.offset		= MTDPART_OFS_APPEND,
-		.mask_flags	= MTD_WRITEABLE  /* force read-only */
-	} , {
-		.name		= "kernel",
-		.size		= 0x00160000,
-		.offset		= MTDPART_OFS_APPEND,
-	} , {
-		.name		= "ramdisk",
-		.size		= MTDPART_SIZ_FULL,
-		.offset		= MTDPART_OFS_APPEND
-	}
-};
-
-static struct physmap_flash_data cmx255_nor_flash_data[] = {
-	{
-		.width		= 2,	/* bankwidth in bytes */
-		.parts		= cmx255_nor_partitions,
-		.nr_parts	= ARRAY_SIZE(cmx255_nor_partitions)
-	}
-};
-
-static struct resource cmx255_nor_resource = {
-	.start	= PXA_CS0_PHYS,
-	.end	= PXA_CS0_PHYS + SZ_8M - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device cmx255_nor = {
-	.name	= "physmap-flash",
-	.id	= -1,
-	.dev	= {
-		.platform_data = cmx255_nor_flash_data,
-	},
-	.resource = &cmx255_nor_resource,
-	.num_resources = 1,
-};
-
-static void __init cmx255_init_nor(void)
-{
-	platform_device_register(&cmx255_nor);
-}
-#else
-static inline void cmx255_init_nor(void) {}
-#endif
-
-#if defined(CONFIG_MTD_NAND_GPIO) || defined(CONFIG_MTD_NAND_GPIO_MODULE)
-
-static struct gpiod_lookup_table cmx255_nand_gpiod_table = {
-	.dev_id         = "gpio-nand",
-	.table          = {
-		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_CS, "nce", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_CLE, "cle", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_ALE, "ale", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_RB, "rdy", GPIO_ACTIVE_HIGH),
-	},
-};
-
-static struct resource cmx255_nand_resource[] = {
-	[0] = {
-		.start = PXA_CS1_PHYS,
-		.end   = PXA_CS1_PHYS + 11,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = PXA_CS5_PHYS,
-		.end   = PXA_CS5_PHYS + 3,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct mtd_partition cmx255_nand_parts[] = {
-	[0] = {
-		.name	= "cmx255-nand",
-		.size	= MTDPART_SIZ_FULL,
-		.offset	= 0,
-	},
-};
-
-static struct gpio_nand_platdata cmx255_nand_platdata = {
-	.parts = cmx255_nand_parts,
-	.num_parts = ARRAY_SIZE(cmx255_nand_parts),
-	.chip_delay = 25,
-};
-
-static struct platform_device cmx255_nand = {
-	.name		= "gpio-nand",
-	.num_resources	= ARRAY_SIZE(cmx255_nand_resource),
-	.resource	= cmx255_nand_resource,
-	.id		= -1,
-	.dev		= {
-		.platform_data = &cmx255_nand_platdata,
-	}
-};
-
-static void __init cmx255_init_nand(void)
-{
-	gpiod_add_lookup_table(&cmx255_nand_gpiod_table);
-	platform_device_register(&cmx255_nand);
-}
-#else
-static inline void cmx255_init_nand(void) {}
-#endif
-
-void __init cmx255_init(void)
-{
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx255_pin_config));
-
-	cmx255_init_rtc();
-	cmx255_init_nor();
-	cmx255_init_nand();
-}
diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c
deleted file mode 100644
index 9baad11314f2..000000000000
--- a/arch/arm/mach-pxa/cm-x270.c
+++ /dev/null
@@ -1,419 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-pxa/cm-x270.c
- *
- * Copyright (C) 2007, 2008 CompuLab, Ltd.
- * Mike Rapoport <mike@compulab.co.il>
- */
-
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/delay.h>
-
-#include <linux/platform_data/rtc-v3020.h>
-#include <video/mbxfb.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/pxa2xx_spi.h>
-#include <linux/spi/libertas_spi.h>
-
-#include "pxa27x.h"
-#include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <linux/platform_data/mmc-pxamci.h>
-
-#include "generic.h"
-
-/* physical address if local-bus attached devices */
-#define RTC_PHYS_BASE		(PXA_CS1_PHYS + (5 << 22))
-
-/* GPIO IRQ usage */
-#define GPIO83_MMC_IRQ		(83)
-
-#define CMX270_MMC_IRQ		PXA_GPIO_TO_IRQ(GPIO83_MMC_IRQ)
-
-/* MMC power enable */
-#define GPIO105_MMC_POWER	(105)
-
-/* WLAN GPIOS */
-#define GPIO19_WLAN_STRAP	(19)
-#define GPIO102_WLAN_RST	(102)
-
-static unsigned long cmx270_pin_config[] = {
-	/* AC'97 */
-	GPIO28_AC97_BITCLK,
-	GPIO29_AC97_SDATA_IN_0,
-	GPIO30_AC97_SDATA_OUT,
-	GPIO31_AC97_SYNC,
-	GPIO98_AC97_SYSCLK,
-	GPIO113_AC97_nRESET,
-
-	/* BTUART */
-	GPIO42_BTUART_RXD,
-	GPIO43_BTUART_TXD,
-	GPIO44_BTUART_CTS,
-	GPIO45_BTUART_RTS,
-
-	/* STUART */
-	GPIO46_STUART_RXD,
-	GPIO47_STUART_TXD,
-
-	/* MCI controller */
-	GPIO32_MMC_CLK,
-	GPIO112_MMC_CMD,
-	GPIO92_MMC_DAT_0,
-	GPIO109_MMC_DAT_1,
-	GPIO110_MMC_DAT_2,
-	GPIO111_MMC_DAT_3,
-
-	/* LCD */
-	GPIOxx_LCD_TFT_16BPP,
-
-	/* I2C */
-	GPIO117_I2C_SCL,
-	GPIO118_I2C_SDA,
-
-	/* SSP1 */
-	GPIO23_SSP1_SCLK,
-	GPIO24_SSP1_SFRM,
-	GPIO25_SSP1_TXD,
-	GPIO26_SSP1_RXD,
-
-	/* SSP2 */
-	GPIO19_GPIO,	/* SSP2 clock is used as GPIO for Libertas pin-strap */
-	GPIO14_GPIO,
-	GPIO87_SSP2_TXD,
-	GPIO88_SSP2_RXD,
-
-	/* PC Card */
-	GPIO48_nPOE,
-	GPIO49_nPWE,
-	GPIO50_nPIOR,
-	GPIO51_nPIOW,
-	GPIO85_nPCE_1,
-	GPIO54_nPCE_2,
-	GPIO55_nPREG,
-	GPIO56_nPWAIT,
-	GPIO57_nIOIS16,
-
-	/* SDRAM and local bus */
-	GPIO15_nCS_1,
-	GPIO78_nCS_2,
-	GPIO79_nCS_3,
-	GPIO80_nCS_4,
-	GPIO33_nCS_5,
-	GPIO49_nPWE,
-	GPIO18_RDY,
-
-	/* GPIO */
-	GPIO0_GPIO	| WAKEUP_ON_EDGE_BOTH,
-	GPIO105_GPIO	| MFP_LPM_DRIVE_HIGH,	/* MMC/SD power */
-	GPIO53_GPIO,				/* PC card reset */
-	GPIO102_GPIO,				/* WLAN reset */
-
-	/* NAND controls */
-	GPIO11_GPIO	| MFP_LPM_DRIVE_HIGH,	/* NAND CE# */
-	GPIO89_GPIO,				/* NAND Ready/Busy */
-
-	/* interrupts */
-	GPIO10_GPIO,	/* DM9000 interrupt */
-	GPIO83_GPIO,	/* MMC card detect */
-	GPIO95_GPIO,	/* WLAN interrupt */
-};
-
-/* V3020 RTC */
-#if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE)
-static struct resource cmx270_v3020_resource[] = {
-	[0] = {
-		.start = RTC_PHYS_BASE,
-		.end   = RTC_PHYS_BASE + 4,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-struct v3020_platform_data cmx270_v3020_pdata = {
-	.leftshift = 16,
-};
-
-static struct platform_device cmx270_rtc_device = {
-	.name		= "v3020",
-	.num_resources	= ARRAY_SIZE(cmx270_v3020_resource),
-	.resource	= cmx270_v3020_resource,
-	.id		= -1,
-	.dev		= {
-		.platform_data = &cmx270_v3020_pdata,
-	}
-};
-
-static void __init cmx270_init_rtc(void)
-{
-	platform_device_register(&cmx270_rtc_device);
-}
-#else
-static inline void cmx270_init_rtc(void) {}
-#endif
-
-/* 2700G graphics */
-#if defined(CONFIG_FB_MBX) || defined(CONFIG_FB_MBX_MODULE)
-static u64 fb_dma_mask = ~(u64)0;
-
-static struct resource cmx270_2700G_resource[] = {
-	/* frame buffer memory including ODFB and External SDRAM */
-	[0] = {
-		.start = PXA_CS2_PHYS,
-		.end   = PXA_CS2_PHYS + 0x01ffffff,
-		.flags = IORESOURCE_MEM,
-	},
-	/* Marathon registers */
-	[1] = {
-		.start = PXA_CS2_PHYS + 0x03fe0000,
-		.end   = PXA_CS2_PHYS + 0x03ffffff,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static unsigned long cmx270_marathon_on[] = {
-	GPIO58_GPIO,
-	GPIO59_GPIO,
-	GPIO60_GPIO,
-	GPIO61_GPIO,
-	GPIO62_GPIO,
-	GPIO63_GPIO,
-	GPIO64_GPIO,
-	GPIO65_GPIO,
-	GPIO66_GPIO,
-	GPIO67_GPIO,
-	GPIO68_GPIO,
-	GPIO69_GPIO,
-	GPIO70_GPIO,
-	GPIO71_GPIO,
-	GPIO72_GPIO,
-	GPIO73_GPIO,
-	GPIO74_GPIO,
-	GPIO75_GPIO,
-	GPIO76_GPIO,
-	GPIO77_GPIO,
-};
-
-static unsigned long cmx270_marathon_off[] = {
-	GPIOxx_LCD_TFT_16BPP,
-};
-
-static int cmx270_marathon_probe(struct fb_info *fb)
-{
-	int gpio, err;
-
-	for (gpio = 58; gpio <= 77; gpio++) {
-		err = gpio_request(gpio, "LCD");
-		if (err)
-			return err;
-		gpio_direction_input(gpio);
-	}
-
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_on));
-	return 0;
-}
-
-static int cmx270_marathon_remove(struct fb_info *fb)
-{
-	int gpio;
-
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_off));
-
-	for (gpio = 58; gpio <= 77; gpio++)
-		gpio_free(gpio);
-
-	return 0;
-}
-
-static struct mbxfb_platform_data cmx270_2700G_data = {
-	.xres = {
-		.min = 240,
-		.max = 1200,
-		.defval = 640,
-	},
-	.yres = {
-		.min = 240,
-		.max = 1200,
-		.defval = 480,
-	},
-	.bpp = {
-		.min = 16,
-		.max = 32,
-		.defval = 16,
-	},
-	.memsize = 8*1024*1024,
-	.probe = cmx270_marathon_probe,
-	.remove = cmx270_marathon_remove,
-};
-
-static struct platform_device cmx270_2700G = {
-	.name		= "mbx-fb",
-	.dev		= {
-		.platform_data	= &cmx270_2700G_data,
-		.dma_mask	= &fb_dma_mask,
-		.coherent_dma_mask = 0xffffffff,
-	},
-	.num_resources	= ARRAY_SIZE(cmx270_2700G_resource),
-	.resource	= cmx270_2700G_resource,
-	.id		= -1,
-};
-
-static void __init cmx270_init_2700G(void)
-{
-	platform_device_register(&cmx270_2700G);
-}
-#else
-static inline void cmx270_init_2700G(void) {}
-#endif
-
-/* PXA27x OHCI controller setup */
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static struct pxaohci_platform_data cmx270_ohci_platform_data = {
-	.port_mode	= PMM_PERPORT_MODE,
-	.flags		= ENABLE_PORT1 | ENABLE_PORT2 | POWER_CONTROL_LOW,
-};
-
-static void __init cmx270_init_ohci(void)
-{
-	pxa_set_ohci_info(&cmx270_ohci_platform_data);
-}
-#else
-static inline void cmx270_init_ohci(void) {}
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
-static struct pxamci_platform_data cmx270_mci_platform_data = {
-	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
-};
-
-static struct gpiod_lookup_table cmx270_mci_gpio_table = {
-	.dev_id = "pxa2xx-mci.0",
-	.table = {
-		/* Card detect on GPIO 83 */
-		GPIO_LOOKUP("gpio-pxa", GPIO83_MMC_IRQ, "cd", GPIO_ACTIVE_LOW),
-		/* Power on GPIO 105 */
-		GPIO_LOOKUP("gpio-pxa", GPIO105_MMC_POWER,
-			    "power", GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-static void __init cmx270_init_mmc(void)
-{
-	gpiod_add_lookup_table(&cmx270_mci_gpio_table);
-	pxa_set_mci_info(&cmx270_mci_platform_data);
-}
-#else
-static inline void cmx270_init_mmc(void) {}
-#endif
-
-#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_controller cm_x270_spi_info = {
-	.num_chipselect	= 1,
-	.enable_dma	= 1,
-};
-
-static struct pxa2xx_spi_chip cm_x270_libertas_chip = {
-	.rx_threshold	= 1,
-	.tx_threshold	= 1,
-	.timeout	= 1000,
-	.gpio_cs	= 14,
-};
-
-static unsigned long cm_x270_libertas_pin_config[] = {
-	/* SSP2 */
-	GPIO19_SSP2_SCLK,
-	GPIO14_GPIO,
-	GPIO87_SSP2_TXD,
-	GPIO88_SSP2_RXD,
-
-};
-
-static int cm_x270_libertas_setup(struct spi_device *spi)
-{
-	int err = gpio_request(GPIO19_WLAN_STRAP, "WLAN STRAP");
-	if (err)
-		return err;
-
-	err = gpio_request(GPIO102_WLAN_RST, "WLAN RST");
-	if (err)
-		goto err_free_strap;
-
-	err = gpio_direction_output(GPIO102_WLAN_RST, 0);
-	if (err)
-		goto err_free_strap;
-	msleep(100);
-
-	err = gpio_direction_output(GPIO19_WLAN_STRAP, 1);
-	if (err)
-		goto err_free_strap;
-	msleep(100);
-
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(cm_x270_libertas_pin_config));
-
-	gpio_set_value(GPIO102_WLAN_RST, 1);
-	msleep(100);
-
-	spi->bits_per_word = 16;
-	spi_setup(spi);
-
-	return 0;
-
-err_free_strap:
-	gpio_free(GPIO19_WLAN_STRAP);
-
-	return err;
-}
-
-static int cm_x270_libertas_teardown(struct spi_device *spi)
-{
-	gpio_set_value(GPIO102_WLAN_RST, 0);
-	gpio_free(GPIO102_WLAN_RST);
-	gpio_free(GPIO19_WLAN_STRAP);
-
-	return 0;
-}
-
-struct libertas_spi_platform_data cm_x270_libertas_pdata = {
-	.use_dummy_writes	= 1,
-	.setup			= cm_x270_libertas_setup,
-	.teardown		= cm_x270_libertas_teardown,
-};
-
-static struct spi_board_info cm_x270_spi_devices[] __initdata = {
-	{
-		.modalias		= "libertas_spi",
-		.max_speed_hz		= 13000000,
-		.bus_num		= 2,
-		.irq			= PXA_GPIO_TO_IRQ(95),
-		.chip_select		= 0,
-		.controller_data	= &cm_x270_libertas_chip,
-		.platform_data		= &cm_x270_libertas_pdata,
-	},
-};
-
-static void __init cmx270_init_spi(void)
-{
-	pxa2xx_set_spi_info(2, &cm_x270_spi_info);
-	spi_register_board_info(ARRAY_AND_SIZE(cm_x270_spi_devices));
-}
-#else
-static inline void cmx270_init_spi(void) {}
-#endif
-
-void __init cmx270_init(void)
-{
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_pin_config));
-
-#ifdef CONFIG_PM
-	pxa27x_set_pwrmode(PWRMODE_DEEPSLEEP);
-#endif
-
-	cmx270_init_rtc();
-	cmx270_init_mmc();
-	cmx270_init_ohci();
-	cmx270_init_2700G();
-	cmx270_init_spi();
-}
diff --git a/arch/arm/mach-pxa/cm-x2xx-pci.c b/arch/arm/mach-pxa/cm-x2xx-pci.c
deleted file mode 100644
index f1c61c6b5610..000000000000
--- a/arch/arm/mach-pxa/cm-x2xx-pci.c
+++ /dev/null
@@ -1,196 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-pxa/cm-x2xx-pci.c
- *
- * PCI bios-type initialisation for PCI machines
- *
- * Bits taken from various places.
- *
- * Copyright (C) 2007, 2008 Compulab, Ltd.
- * Mike Rapoport <mike@compulab.co.il>
- */
-
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-
-#include <asm/hardware/it8152.h>
-
-void __iomem *it8152_base_address;
-static int cmx2xx_it8152_irq_gpio;
-
-static void cmx2xx_it8152_irq_demux(struct irq_desc *desc)
-{
-	/* clear our parent irq */
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-
-	it8152_irq_demux(desc);
-}
-
-void __cmx2xx_pci_init_irq(int irq_gpio)
-{
-	it8152_init_irq();
-
-	cmx2xx_it8152_irq_gpio = irq_gpio;
-
-	irq_set_irq_type(gpio_to_irq(irq_gpio), IRQ_TYPE_EDGE_RISING);
-
-	irq_set_chained_handler(gpio_to_irq(irq_gpio),
-				cmx2xx_it8152_irq_demux);
-}
-
-#ifdef CONFIG_PM
-static unsigned long sleep_save_ite[10];
-
-void __cmx2xx_pci_suspend(void)
-{
-	/* save ITE state */
-	sleep_save_ite[0] = __raw_readl(IT8152_INTC_PDCNIMR);
-	sleep_save_ite[1] = __raw_readl(IT8152_INTC_LPCNIMR);
-	sleep_save_ite[2] = __raw_readl(IT8152_INTC_LPNIAR);
-
-	/* Clear ITE IRQ's */
-	__raw_writel((0), IT8152_INTC_PDCNIRR);
-	__raw_writel((0), IT8152_INTC_LPCNIRR);
-}
-
-void __cmx2xx_pci_resume(void)
-{
-	/* restore IT8152 state */
-	__raw_writel((sleep_save_ite[0]), IT8152_INTC_PDCNIMR);
-	__raw_writel((sleep_save_ite[1]), IT8152_INTC_LPCNIMR);
-	__raw_writel((sleep_save_ite[2]), IT8152_INTC_LPNIAR);
-}
-#else
-void cmx2xx_pci_suspend(void) {}
-void cmx2xx_pci_resume(void) {}
-#endif
-
-/* PCI IRQ mapping*/
-static int __init cmx2xx_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	int irq;
-
-	dev_dbg(&dev->dev, "%s: slot=%x, pin=%x\n", __func__, slot, pin);
-
-	irq = it8152_pci_map_irq(dev, slot, pin);
-	if (irq)
-		return irq;
-
-	/*
-	  Here comes the ugly part. The routing is baseboard specific,
-	  but defining a platform for each possible base of CM-X2XX is
-	  unrealistic. Here we keep mapping for ATXBase and SB-X2XX.
-	*/
-	/* ATXBASE PCI slot */
-	if (slot == 7)
-		return IT8152_PCI_INTA;
-
-	/* ATXBase/SB-X2XX CardBus */
-	if (slot == 8 || slot == 0)
-		return IT8152_PCI_INTB;
-
-	/* ATXBase Ethernet */
-	if (slot == 9)
-		return IT8152_PCI_INTA;
-
-	/* CM-x255 Onboard Ethernet */
-	if (slot == 15)
-		return IT8152_PCI_INTC;
-
-	/* SB-x2xx Ethernet */
-	if (slot == 16)
-		return IT8152_PCI_INTA;
-
-	/* PC104+ interrupt routing */
-	if ((slot == 17) || (slot == 19))
-		return IT8152_PCI_INTA;
-	if ((slot == 18) || (slot == 20))
-		return IT8152_PCI_INTB;
-
-	return(0);
-}
-
-static void cmx2xx_pci_preinit(void)
-{
-	pr_info("Initializing CM-X2XX PCI subsystem\n");
-
-	pcibios_min_io = 0;
-	pcibios_min_mem = 0;
-
-	__raw_writel(0x800, IT8152_PCI_CFG_ADDR);
-	if (__raw_readl(IT8152_PCI_CFG_DATA) == 0x81521283) {
-		pr_info("PCI Bridge found.\n");
-
-		/* set PCI I/O base at 0 */
-		writel(0x848, IT8152_PCI_CFG_ADDR);
-		writel(0, IT8152_PCI_CFG_DATA);
-
-		/* set PCI memory base at 0 */
-		writel(0x840, IT8152_PCI_CFG_ADDR);
-		writel(0, IT8152_PCI_CFG_DATA);
-
-		writel(0x20, IT8152_GPIO_GPDR);
-
-		/* CardBus Controller on ATXbase baseboard */
-		writel(0x4000, IT8152_PCI_CFG_ADDR);
-		if (readl(IT8152_PCI_CFG_DATA) == 0xAC51104C) {
-			pr_info("CardBus Bridge found.\n");
-
-			/* Configure socket 0 */
-			writel(0x408C, IT8152_PCI_CFG_ADDR);
-			writel(0x1022, IT8152_PCI_CFG_DATA);
-
-			writel(0x4080, IT8152_PCI_CFG_ADDR);
-			writel(0x3844d060, IT8152_PCI_CFG_DATA);
-
-			writel(0x4090, IT8152_PCI_CFG_ADDR);
-			writel(((readl(IT8152_PCI_CFG_DATA) & 0xffff) |
-				0x60440000),
-			       IT8152_PCI_CFG_DATA);
-
-			writel(0x4018, IT8152_PCI_CFG_ADDR);
-			writel(0xb0000000, IT8152_PCI_CFG_DATA);
-
-			/* Configure socket 1 */
-			writel(0x418C, IT8152_PCI_CFG_ADDR);
-			writel(0x1022, IT8152_PCI_CFG_DATA);
-
-			writel(0x4180, IT8152_PCI_CFG_ADDR);
-			writel(0x3844d060, IT8152_PCI_CFG_DATA);
-
-			writel(0x4190, IT8152_PCI_CFG_ADDR);
-			writel(((readl(IT8152_PCI_CFG_DATA) & 0xffff) |
-				0x60440000),
-			       IT8152_PCI_CFG_DATA);
-
-			writel(0x4118, IT8152_PCI_CFG_ADDR);
-			writel(0xb0000000, IT8152_PCI_CFG_DATA);
-		}
-	}
-}
-
-static struct hw_pci cmx2xx_pci __initdata = {
-	.map_irq	= cmx2xx_pci_map_irq,
-	.nr_controllers	= 1,
-	.ops		= &it8152_ops,
-	.setup		= it8152_pci_setup,
-	.preinit	= cmx2xx_pci_preinit,
-};
-
-static int __init cmx2xx_init_pci(void)
-{
-	if (machine_is_armcore())
-		pci_common_init(&cmx2xx_pci);
-
-	return 0;
-}
-
-subsys_initcall(cmx2xx_init_pci);
diff --git a/arch/arm/mach-pxa/cm-x2xx-pci.h b/arch/arm/mach-pxa/cm-x2xx-pci.h
deleted file mode 100644
index 93ffaaee75d7..000000000000
--- a/arch/arm/mach-pxa/cm-x2xx-pci.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-extern void __cmx2xx_pci_init_irq(int irq_gpio);
-extern void __cmx2xx_pci_suspend(void);
-extern void __cmx2xx_pci_resume(void);
-
-#ifdef CONFIG_PCI
-#define cmx2xx_pci_init_irq(x) __cmx2xx_pci_init_irq(x)
-#define cmx2xx_pci_suspend(x) __cmx2xx_pci_suspend(x)
-#define cmx2xx_pci_resume(x) __cmx2xx_pci_resume(x)
-#else
-#define cmx2xx_pci_init_irq(x) do {} while (0)
-#define cmx2xx_pci_suspend(x) do {} while (0)
-#define cmx2xx_pci_resume(x) do {} while (0)
-#endif
diff --git a/arch/arm/mach-pxa/cm-x2xx.c b/arch/arm/mach-pxa/cm-x2xx.c
deleted file mode 100644
index ff976d1217eb..000000000000
--- a/arch/arm/mach-pxa/cm-x2xx.c
+++ /dev/null
@@ -1,538 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-pxa/cm-x2xx.c
- *
- * Copyright (C) 2008 CompuLab, Ltd.
- * Mike Rapoport <mike@compulab.co.il>
- */
-
-#include <linux/platform_device.h>
-#include <linux/syscore_ops.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-#include <linux/regulator/machine.h>
-
-#include <linux/dm9000.h>
-#include <linux/leds.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <asm/mach/map.h>
-
-#include "pxa25x.h"
-#undef GPIO24_SSP1_SFRM
-#undef GPIO86_GPIO
-#undef GPIO87_GPIO
-#undef GPIO88_GPIO
-#undef GPIO89_GPIO
-#include "pxa27x.h"
-#undef GPIO24_SSP1_SFRM
-#undef GPIO86_GPIO
-#undef GPIO87_GPIO
-#undef GPIO88_GPIO
-#undef GPIO89_GPIO
-#include <mach/audio.h>
-#include <linux/platform_data/video-pxafb.h>
-#include <mach/smemc.h>
-
-#include <asm/hardware/it8152.h>
-
-#include "generic.h"
-#include "cm-x2xx-pci.h"
-
-extern void cmx255_init(void);
-extern void cmx270_init(void);
-
-/* reserve IRQs for IT8152 */
-#define CMX2XX_NR_IRQS		(IRQ_BOARD_START + 40)
-
-/* virtual addresses for statically mapped regions */
-#define CMX2XX_VIRT_BASE	(void __iomem *)(0xe8000000)
-#define CMX2XX_IT8152_VIRT	(CMX2XX_VIRT_BASE)
-
-/* physical address if local-bus attached devices */
-#define CMX255_DM9000_PHYS_BASE (PXA_CS1_PHYS + (8 << 22))
-#define CMX270_DM9000_PHYS_BASE	(PXA_CS1_PHYS + (6 << 22))
-
-/* leds */
-#define CMX255_GPIO_RED		(27)
-#define CMX255_GPIO_GREEN	(32)
-#define CMX270_GPIO_RED		(93)
-#define CMX270_GPIO_GREEN	(94)
-
-/* GPIO IRQ usage */
-#define GPIO22_ETHIRQ		(22)
-#define GPIO10_ETHIRQ		(10)
-#define CMX255_GPIO_IT8152_IRQ	(0)
-#define CMX270_GPIO_IT8152_IRQ	(22)
-
-#define CMX255_ETHIRQ		PXA_GPIO_TO_IRQ(GPIO22_ETHIRQ)
-#define CMX270_ETHIRQ		PXA_GPIO_TO_IRQ(GPIO10_ETHIRQ)
-
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
-static struct resource cmx255_dm9000_resource[] = {
-	[0] = {
-		.start = CMX255_DM9000_PHYS_BASE,
-		.end   = CMX255_DM9000_PHYS_BASE + 3,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = CMX255_DM9000_PHYS_BASE + 4,
-		.end   = CMX255_DM9000_PHYS_BASE + 4 + 500,
-		.flags = IORESOURCE_MEM,
-	},
-	[2] = {
-		.start = CMX255_ETHIRQ,
-		.end   = CMX255_ETHIRQ,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	}
-};
-
-static struct resource cmx270_dm9000_resource[] = {
-	[0] = {
-		.start = CMX270_DM9000_PHYS_BASE,
-		.end   = CMX270_DM9000_PHYS_BASE + 3,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = CMX270_DM9000_PHYS_BASE + 8,
-		.end   = CMX270_DM9000_PHYS_BASE + 8 + 500,
-		.flags = IORESOURCE_MEM,
-	},
-	[2] = {
-		.start = CMX270_ETHIRQ,
-		.end   = CMX270_ETHIRQ,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	}
-};
-
-static struct dm9000_plat_data cmx270_dm9000_platdata = {
-	.flags		= DM9000_PLATF_32BITONLY | DM9000_PLATF_NO_EEPROM,
-};
-
-static struct platform_device cmx2xx_dm9000_device = {
-	.name		= "dm9000",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(cmx270_dm9000_resource),
-	.dev		= {
-		.platform_data = &cmx270_dm9000_platdata,
-	}
-};
-
-static void __init cmx2xx_init_dm9000(void)
-{
-	if (cpu_is_pxa25x())
-		cmx2xx_dm9000_device.resource = cmx255_dm9000_resource;
-	else
-		cmx2xx_dm9000_device.resource = cmx270_dm9000_resource;
-	platform_device_register(&cmx2xx_dm9000_device);
-}
-#else
-static inline void cmx2xx_init_dm9000(void) {}
-#endif
-
-/* UCB1400 touchscreen controller */
-#if defined(CONFIG_TOUCHSCREEN_UCB1400) || defined(CONFIG_TOUCHSCREEN_UCB1400_MODULE)
-static struct platform_device cmx2xx_ts_device = {
-	.name		= "ucb1400_core",
-	.id		= -1,
-};
-
-static void __init cmx2xx_init_touchscreen(void)
-{
-	platform_device_register(&cmx2xx_ts_device);
-}
-#else
-static inline void cmx2xx_init_touchscreen(void) {}
-#endif
-
-/* CM-X270 LEDs */
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-static struct gpio_led cmx2xx_leds[] = {
-	[0] = {
-		.name = "cm-x2xx:red",
-		.default_trigger = "nand-disk",
-		.active_low = 1,
-	},
-	[1] = {
-		.name = "cm-x2xx:green",
-		.default_trigger = "heartbeat",
-		.active_low = 1,
-	},
-};
-
-static struct gpio_led_platform_data cmx2xx_gpio_led_pdata = {
-	.num_leds = ARRAY_SIZE(cmx2xx_leds),
-	.leds = cmx2xx_leds,
-};
-
-static struct platform_device cmx2xx_led_device = {
-	.name		= "leds-gpio",
-	.id		= -1,
-	.dev		= {
-		.platform_data = &cmx2xx_gpio_led_pdata,
-	},
-};
-
-static void __init cmx2xx_init_leds(void)
-{
-	if (cpu_is_pxa25x()) {
-		cmx2xx_leds[0].gpio = CMX255_GPIO_RED;
-		cmx2xx_leds[1].gpio = CMX255_GPIO_GREEN;
-	} else {
-		cmx2xx_leds[0].gpio = CMX270_GPIO_RED;
-		cmx2xx_leds[1].gpio = CMX270_GPIO_GREEN;
-	}
-	platform_device_register(&cmx2xx_led_device);
-}
-#else
-static inline void cmx2xx_init_leds(void) {}
-#endif
-
-#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
-/*
-  Display definitions
-  keep these for backwards compatibility, although symbolic names (as
-  e.g. in lpd270.c) looks better
-*/
-#define MTYPE_STN320x240	0
-#define MTYPE_TFT640x480	1
-#define MTYPE_CRT640x480	2
-#define MTYPE_CRT800x600	3
-#define MTYPE_TFT320x240	6
-#define MTYPE_STN640x480	7
-
-static struct pxafb_mode_info generic_stn_320x240_mode = {
-	.pixclock	= 76923,
-	.bpp		= 8,
-	.xres		= 320,
-	.yres		= 240,
-	.hsync_len	= 3,
-	.vsync_len	= 2,
-	.left_margin	= 3,
-	.upper_margin	= 0,
-	.right_margin	= 3,
-	.lower_margin	= 0,
-	.sync		= (FB_SYNC_HOR_HIGH_ACT |
-			   FB_SYNC_VERT_HIGH_ACT),
-	.cmap_greyscale = 0,
-};
-
-static struct pxafb_mach_info generic_stn_320x240 = {
-	.modes		= &generic_stn_320x240_mode,
-	.num_modes	= 1,
-	.lcd_conn	= LCD_COLOR_STN_8BPP | LCD_PCLK_EDGE_FALL |\
-			  LCD_AC_BIAS_FREQ(0xff),
-	.cmap_inverse	= 0,
-	.cmap_static	= 0,
-};
-
-static struct pxafb_mode_info generic_tft_640x480_mode = {
-	.pixclock	= 38461,
-	.bpp		= 8,
-	.xres		= 640,
-	.yres		= 480,
-	.hsync_len	= 60,
-	.vsync_len	= 2,
-	.left_margin	= 70,
-	.upper_margin	= 10,
-	.right_margin	= 70,
-	.lower_margin	= 5,
-	.sync		= 0,
-	.cmap_greyscale = 0,
-};
-
-static struct pxafb_mach_info generic_tft_640x480 = {
-	.modes		= &generic_tft_640x480_mode,
-	.num_modes	= 1,
-	.lcd_conn	= LCD_COLOR_TFT_8BPP | LCD_PCLK_EDGE_FALL |\
-			  LCD_AC_BIAS_FREQ(0xff),
-	.cmap_inverse	= 0,
-	.cmap_static	= 0,
-};
-
-static struct pxafb_mode_info generic_crt_640x480_mode = {
-	.pixclock	= 38461,
-	.bpp		= 8,
-	.xres		= 640,
-	.yres		= 480,
-	.hsync_len	= 63,
-	.vsync_len	= 2,
-	.left_margin	= 81,
-	.upper_margin	= 33,
-	.right_margin	= 16,
-	.lower_margin	= 10,
-	.sync		= (FB_SYNC_HOR_HIGH_ACT |
-			   FB_SYNC_VERT_HIGH_ACT),
-	.cmap_greyscale = 0,
-};
-
-static struct pxafb_mach_info generic_crt_640x480 = {
-	.modes		= &generic_crt_640x480_mode,
-	.num_modes	= 1,
-	.lcd_conn	= LCD_COLOR_TFT_8BPP | LCD_AC_BIAS_FREQ(0xff),
-	.cmap_inverse	= 0,
-	.cmap_static	= 0,
-};
-
-static struct pxafb_mode_info generic_crt_800x600_mode = {
-	.pixclock	= 28846,
-	.bpp		= 8,
-	.xres		= 800,
-	.yres	  	= 600,
-	.hsync_len	= 63,
-	.vsync_len	= 2,
-	.left_margin	= 26,
-	.upper_margin	= 21,
-	.right_margin	= 26,
-	.lower_margin	= 11,
-	.sync		= (FB_SYNC_HOR_HIGH_ACT |
-			   FB_SYNC_VERT_HIGH_ACT),
-	.cmap_greyscale = 0,
-};
-
-static struct pxafb_mach_info generic_crt_800x600 = {
-	.modes		= &generic_crt_800x600_mode,
-	.num_modes	= 1,
-	.lcd_conn	= LCD_COLOR_TFT_8BPP | LCD_AC_BIAS_FREQ(0xff),
-	.cmap_inverse	= 0,
-	.cmap_static	= 0,
-};
-
-static struct pxafb_mode_info generic_tft_320x240_mode = {
-	.pixclock	= 134615,
-	.bpp		= 16,
-	.xres		= 320,
-	.yres		= 240,
-	.hsync_len	= 63,
-	.vsync_len	= 7,
-	.left_margin	= 75,
-	.upper_margin	= 0,
-	.right_margin	= 15,
-	.lower_margin	= 15,
-	.sync		= 0,
-	.cmap_greyscale = 0,
-};
-
-static struct pxafb_mach_info generic_tft_320x240 = {
-	.modes		= &generic_tft_320x240_mode,
-	.num_modes	= 1,
-	.lcd_conn	= LCD_COLOR_TFT_16BPP | LCD_AC_BIAS_FREQ(0xff),
-	.cmap_inverse	= 0,
-	.cmap_static	= 0,
-};
-
-static struct pxafb_mode_info generic_stn_640x480_mode = {
-	.pixclock	= 57692,
-	.bpp		= 8,
-	.xres		= 640,
-	.yres		= 480,
-	.hsync_len	= 4,
-	.vsync_len	= 2,
-	.left_margin	= 10,
-	.upper_margin	= 5,
-	.right_margin	= 10,
-	.lower_margin	= 5,
-	.sync		= (FB_SYNC_HOR_HIGH_ACT |
-			   FB_SYNC_VERT_HIGH_ACT),
-	.cmap_greyscale = 0,
-};
-
-static struct pxafb_mach_info generic_stn_640x480 = {
-	.modes		= &generic_stn_640x480_mode,
-	.num_modes	= 1,
-	.lcd_conn	= LCD_COLOR_STN_8BPP | LCD_AC_BIAS_FREQ(0xff),
-	.cmap_inverse	= 0,
-	.cmap_static	= 0,
-};
-
-static struct pxafb_mach_info *cmx2xx_display = &generic_crt_640x480;
-
-static int __init cmx2xx_set_display(char *str)
-{
-	int disp_type = simple_strtol(str, NULL, 0);
-	switch (disp_type) {
-	case MTYPE_STN320x240:
-		cmx2xx_display = &generic_stn_320x240;
-		break;
-	case MTYPE_TFT640x480:
-		cmx2xx_display = &generic_tft_640x480;
-		break;
-	case MTYPE_CRT640x480:
-		cmx2xx_display = &generic_crt_640x480;
-		break;
-	case MTYPE_CRT800x600:
-		cmx2xx_display = &generic_crt_800x600;
-		break;
-	case MTYPE_TFT320x240:
-		cmx2xx_display = &generic_tft_320x240;
-		break;
-	case MTYPE_STN640x480:
-		cmx2xx_display = &generic_stn_640x480;
-		break;
-	default: /* fallback to CRT 640x480 */
-		cmx2xx_display = &generic_crt_640x480;
-		break;
-	}
-	return 1;
-}
-
-/*
-   This should be done really early to get proper configuration for
-   frame buffer.
-   Indeed, pxafb parameters can be used istead, but CM-X2XX bootloader
-   has limitied line length for kernel command line, and also it will
-   break compatibitlty with proprietary releases already in field.
-*/
-__setup("monitor=", cmx2xx_set_display);
-
-static void __init cmx2xx_init_display(void)
-{
-	pxa_set_fb_info(NULL, cmx2xx_display);
-}
-#else
-static inline void cmx2xx_init_display(void) {}
-#endif
-
-#ifdef CONFIG_PM
-static unsigned long sleep_save_msc[10];
-
-static int cmx2xx_suspend(void)
-{
-	cmx2xx_pci_suspend();
-
-	/* save MSC registers */
-	sleep_save_msc[0] = __raw_readl(MSC0);
-	sleep_save_msc[1] = __raw_readl(MSC1);
-	sleep_save_msc[2] = __raw_readl(MSC2);
-
-	/* setup power saving mode registers */
-	PCFR = 0x0;
-	PSLR = 0xff400000;
-	PMCR  = 0x00000005;
-	PWER  = 0x80000000;
-	PFER  = 0x00000000;
-	PRER  = 0x00000000;
-	PGSR0 = 0xC0018800;
-	PGSR1 = 0x004F0002;
-	PGSR2 = 0x6021C000;
-	PGSR3 = 0x00020000;
-
-	return 0;
-}
-
-static void cmx2xx_resume(void)
-{
-	cmx2xx_pci_resume();
-
-	/* restore MSC registers */
-	__raw_writel(sleep_save_msc[0], MSC0);
-	__raw_writel(sleep_save_msc[1], MSC1);
-	__raw_writel(sleep_save_msc[2], MSC2);
-}
-
-static struct syscore_ops cmx2xx_pm_syscore_ops = {
-	.resume = cmx2xx_resume,
-	.suspend = cmx2xx_suspend,
-};
-
-static int __init cmx2xx_pm_init(void)
-{
-	register_syscore_ops(&cmx2xx_pm_syscore_ops);
-
-	return 0;
-}
-#else
-static int __init cmx2xx_pm_init(void) { return 0; }
-#endif
-
-#if defined(CONFIG_SND_PXA2XX_AC97) || defined(CONFIG_SND_PXA2XX_AC97_MODULE)
-static void __init cmx2xx_init_ac97(void)
-{
-	pxa_set_ac97_info(NULL);
-}
-#else
-static inline void cmx2xx_init_ac97(void) {}
-#endif
-
-static void __init cmx2xx_init(void)
-{
-	pxa_set_ffuart_info(NULL);
-	pxa_set_btuart_info(NULL);
-	pxa_set_stuart_info(NULL);
-
-	cmx2xx_pm_init();
-
-	if (cpu_is_pxa25x())
-		cmx255_init();
-	else
-		cmx270_init();
-
-	cmx2xx_init_dm9000();
-	cmx2xx_init_display();
-	cmx2xx_init_ac97();
-	cmx2xx_init_touchscreen();
-	cmx2xx_init_leds();
-
-	regulator_has_full_constraints();
-}
-
-static void __init cmx2xx_init_irq(void)
-{
-	if (cpu_is_pxa25x()) {
-		pxa25x_init_irq();
-		cmx2xx_pci_init_irq(CMX255_GPIO_IT8152_IRQ);
-	} else {
-		pxa27x_init_irq();
-		cmx2xx_pci_init_irq(CMX270_GPIO_IT8152_IRQ);
-	}
-}
-
-#ifdef CONFIG_PCI
-/* Map PCI companion statically */
-static struct map_desc cmx2xx_io_desc[] __initdata = {
-	[0] = { /* PCI bridge */
-		.virtual	= (unsigned long)CMX2XX_IT8152_VIRT,
-		.pfn		= __phys_to_pfn(PXA_CS4_PHYS),
-		.length		= SZ_64M,
-		.type		= MT_DEVICE
-	},
-};
-
-static void __init cmx2xx_map_io(void)
-{
-	if (cpu_is_pxa25x())
-		pxa25x_map_io();
-
-	if (cpu_is_pxa27x())
-		pxa27x_map_io();
-
-	iotable_init(cmx2xx_io_desc, ARRAY_SIZE(cmx2xx_io_desc));
-
-	it8152_base_address = CMX2XX_IT8152_VIRT;
-}
-#else
-static void __init cmx2xx_map_io(void)
-{
-	if (cpu_is_pxa25x())
-		pxa25x_map_io();
-
-	if (cpu_is_pxa27x())
-		pxa27x_map_io();
-}
-#endif
-
-MACHINE_START(ARMCORE, "Compulab CM-X2XX")
-	.atag_offset	= 0x100,
-	.map_io		= cmx2xx_map_io,
-	.nr_irqs	= CMX2XX_NR_IRQS,
-	.init_irq	= cmx2xx_init_irq,
-	/* NOTE: pxa25x_handle_irq() works on PXA27x w/o camera support */
-	.handle_irq	= pxa25x_handle_irq,
-	.init_time	= pxa_timer_init,
-	.init_machine	= cmx2xx_init,
-#ifdef CONFIG_PCI
-	.dma_zone_size	= SZ_64M,
-#endif
-	.restart	= pxa_restart,
-MACHINE_END
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
deleted file mode 100644
index d8681a331030..000000000000
--- a/arch/arm/mach-pxa/em-x270.c
+++ /dev/null
@@ -1,1286 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Support for CompuLab EM-X270 platform
- *
- * Copyright (C) 2007, 2008 CompuLab, Ltd.
- * Author: Mike Rapoport <mike@compulab.co.il>
- */
-
-#include <linux/irq.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-
-#include <linux/dm9000.h>
-#include <linux/platform_data/rtc-v3020.h>
-#include <linux/mtd/platnand.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/mfd/da903x.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/tdo24m.h>
-#include <linux/spi/libertas_spi.h>
-#include <linux/spi/pxa2xx_spi.h>
-#include <linux/power_supply.h>
-#include <linux/apm-emulation.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/pca953x.h>
-#include <linux/platform_data/i2c-pxa.h>
-#include <linux/regulator/userspace-consumer.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "pxa27x.h"
-#include "pxa27x-udc.h"
-#include <mach/audio.h>
-#include <linux/platform_data/video-pxafb.h>
-#include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <linux/platform_data/mmc-pxamci.h>
-#include <linux/platform_data/keypad-pxa27x.h>
-#include <linux/platform_data/media/camera-pxa.h>
-
-#include "generic.h"
-#include "devices.h"
-
-/* EM-X270 specific GPIOs */
-#define GPIO13_MMC_CD		(13)
-#define GPIO95_MMC_WP		(95)
-#define GPIO56_NAND_RB		(56)
-#define GPIO93_CAM_RESET	(93)
-#define GPIO16_USB_HUB_RESET	(16)
-
-/* eXeda specific GPIOs */
-#define GPIO114_MMC_CD		(114)
-#define GPIO20_NAND_RB		(20)
-#define GPIO38_SD_PWEN		(38)
-#define GPIO37_WLAN_RST		(37)
-#define GPIO95_TOUCHPAD_INT	(95)
-#define GPIO130_CAM_RESET	(130)
-#define GPIO10_USB_HUB_RESET	(10)
-
-/* common  GPIOs */
-#define GPIO11_NAND_CS		(11)
-#define GPIO41_ETHIRQ		(41)
-#define EM_X270_ETHIRQ		PXA_GPIO_TO_IRQ(GPIO41_ETHIRQ)
-#define GPIO115_WLAN_PWEN	(115)
-#define GPIO19_WLAN_STRAP	(19)
-#define GPIO9_USB_VBUS_EN	(9)
-
-static int mmc_cd;
-static int nand_rb;
-static int dm9000_flags;
-static int cam_reset;
-static int usb_hub_reset;
-
-static unsigned long common_pin_config[] = {
-	/* AC'97 */
-	GPIO28_AC97_BITCLK,
-	GPIO29_AC97_SDATA_IN_0,
-	GPIO30_AC97_SDATA_OUT,
-	GPIO31_AC97_SYNC,
-	GPIO98_AC97_SYSCLK,
-	GPIO113_AC97_nRESET,
-
-	/* BTUART */
-	GPIO42_BTUART_RXD,
-	GPIO43_BTUART_TXD,
-	GPIO44_BTUART_CTS,
-	GPIO45_BTUART_RTS,
-
-	/* STUART */
-	GPIO46_STUART_RXD,
-	GPIO47_STUART_TXD,
-
-	/* MCI controller */
-	GPIO32_MMC_CLK,
-	GPIO112_MMC_CMD,
-	GPIO92_MMC_DAT_0,
-	GPIO109_MMC_DAT_1,
-	GPIO110_MMC_DAT_2,
-	GPIO111_MMC_DAT_3,
-
-	/* LCD */
-	GPIOxx_LCD_TFT_16BPP,
-
-	/* QCI */
-	GPIO84_CIF_FV,
-	GPIO25_CIF_LV,
-	GPIO53_CIF_MCLK,
-	GPIO54_CIF_PCLK,
-	GPIO81_CIF_DD_0,
-	GPIO55_CIF_DD_1,
-	GPIO51_CIF_DD_2,
-	GPIO50_CIF_DD_3,
-	GPIO52_CIF_DD_4,
-	GPIO48_CIF_DD_5,
-	GPIO17_CIF_DD_6,
-	GPIO12_CIF_DD_7,
-
-	/* I2C */
-	GPIO117_I2C_SCL,
-	GPIO118_I2C_SDA,
-
-	/* Keypad */
-	GPIO100_KP_MKIN_0	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO101_KP_MKIN_1	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO102_KP_MKIN_2	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO34_KP_MKIN_3	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO39_KP_MKIN_4	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO99_KP_MKIN_5	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO91_KP_MKIN_6	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO36_KP_MKIN_7	| WAKEUP_ON_LEVEL_HIGH,
-	GPIO103_KP_MKOUT_0,
-	GPIO104_KP_MKOUT_1,
-	GPIO105_KP_MKOUT_2,
-	GPIO106_KP_MKOUT_3,
-	GPIO107_KP_MKOUT_4,
-	GPIO108_KP_MKOUT_5,
-	GPIO96_KP_MKOUT_6,
-	GPIO22_KP_MKOUT_7,
-
-	/* SSP1 */
-	GPIO26_SSP1_RXD,
-	GPIO23_SSP1_SCLK,
-	GPIO24_SSP1_SFRM,
-	GPIO57_SSP1_TXD,
-
-	/* SSP2 */
-	GPIO19_GPIO,	/* SSP2 clock is used as GPIO for Libertas pin-strap */
-	GPIO14_GPIO,
-	GPIO89_SSP2_TXD,
-	GPIO88_SSP2_RXD,
-
-	/* SDRAM and local bus */
-	GPIO15_nCS_1,
-	GPIO78_nCS_2,
-	GPIO79_nCS_3,
-	GPIO80_nCS_4,
-	GPIO49_nPWE,
-	GPIO18_RDY,
-
-	/* GPIO */
-	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,	/* sleep/resume button */
-
-	/* power controls */
-	GPIO20_GPIO	| MFP_LPM_DRIVE_LOW,	/* GPRS_PWEN */
-	GPIO115_GPIO	| MFP_LPM_DRIVE_LOW,	/* WLAN_PWEN */
-
-	/* NAND controls */
-	GPIO11_GPIO	| MFP_LPM_DRIVE_HIGH,	/* NAND CE# */
-
-	/* interrupts */
-	GPIO41_GPIO,	/* DM9000 interrupt */
-};
-
-static unsigned long em_x270_pin_config[] = {
-	GPIO13_GPIO,				/* MMC card detect */
-	GPIO16_GPIO,				/* USB hub reset */
-	GPIO56_GPIO,				/* NAND Ready/Busy */
-	GPIO93_GPIO	| MFP_LPM_DRIVE_LOW,	/* Camera reset */
-	GPIO95_GPIO,				/* MMC Write protect */
-};
-
-static unsigned long exeda_pin_config[] = {
-	GPIO10_GPIO,				/* USB hub reset */
-	GPIO20_GPIO,				/* NAND Ready/Busy */
-	GPIO38_GPIO	| MFP_LPM_DRIVE_LOW,	/* SD slot power */
-	GPIO95_GPIO,				/* touchpad IRQ */
-	GPIO114_GPIO,				/* MMC card detect */
-};
-
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
-static struct resource em_x270_dm9000_resource[] = {
-	[0] = {
-		.start = PXA_CS2_PHYS,
-		.end   = PXA_CS2_PHYS + 3,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = PXA_CS2_PHYS + 8,
-		.end   = PXA_CS2_PHYS + 8 + 0x3f,
-		.flags = IORESOURCE_MEM,
-	},
-	[2] = {
-		.start = EM_X270_ETHIRQ,
-		.end   = EM_X270_ETHIRQ,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	}
-};
-
-static struct dm9000_plat_data em_x270_dm9000_platdata = {
-	.flags		= DM9000_PLATF_NO_EEPROM,
-};
-
-static struct platform_device em_x270_dm9000 = {
-	.name		= "dm9000",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(em_x270_dm9000_resource),
-	.resource	= em_x270_dm9000_resource,
-	.dev		= {
-		.platform_data = &em_x270_dm9000_platdata,
-	}
-};
-
-static void __init em_x270_init_dm9000(void)
-{
-	em_x270_dm9000_platdata.flags |= dm9000_flags;
-	platform_device_register(&em_x270_dm9000);
-}
-#else
-static inline void em_x270_init_dm9000(void) {}
-#endif
-
-/* V3020 RTC */
-#if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE)
-static struct resource em_x270_v3020_resource[] = {
-	[0] = {
-		.start = PXA_CS4_PHYS,
-		.end   = PXA_CS4_PHYS + 3,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct v3020_platform_data em_x270_v3020_platdata = {
-	.leftshift = 0,
-};
-
-static struct platform_device em_x270_rtc = {
-	.name		= "v3020",
-	.num_resources	= ARRAY_SIZE(em_x270_v3020_resource),
-	.resource	= em_x270_v3020_resource,
-	.id		= -1,
-	.dev		= {
-		.platform_data = &em_x270_v3020_platdata,
-	}
-};
-
-static void __init em_x270_init_rtc(void)
-{
-	platform_device_register(&em_x270_rtc);
-}
-#else
-static inline void em_x270_init_rtc(void) {}
-#endif
-
-/* NAND flash */
-#if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
-static inline void nand_cs_on(void)
-{
-	gpio_set_value(GPIO11_NAND_CS, 0);
-}
-
-static void nand_cs_off(void)
-{
-	dsb();
-
-	gpio_set_value(GPIO11_NAND_CS, 1);
-}
-
-/* hardware specific access to control-lines */
-static void em_x270_nand_cmd_ctl(struct nand_chip *this, int dat,
-				 unsigned int ctrl)
-{
-	unsigned long nandaddr = (unsigned long)this->legacy.IO_ADDR_W;
-
-	dsb();
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		if (ctrl & NAND_ALE)
-			nandaddr |=  (1 << 3);
-		else
-			nandaddr &= ~(1 << 3);
-		if (ctrl & NAND_CLE)
-			nandaddr |=  (1 << 2);
-		else
-			nandaddr &= ~(1 << 2);
-		if (ctrl & NAND_NCE)
-			nand_cs_on();
-		else
-			nand_cs_off();
-	}
-
-	dsb();
-	this->legacy.IO_ADDR_W = (void __iomem *)nandaddr;
-	if (dat != NAND_CMD_NONE)
-		writel(dat, this->legacy.IO_ADDR_W);
-
-	dsb();
-}
-
-/* read device ready pin */
-static int em_x270_nand_device_ready(struct nand_chip *this)
-{
-	dsb();
-
-	return gpio_get_value(nand_rb);
-}
-
-static struct mtd_partition em_x270_partition_info[] = {
-	[0] = {
-		.name	= "em_x270-0",
-		.offset	= 0,
-		.size	= SZ_4M,
-	},
-	[1] = {
-		.name	= "em_x270-1",
-		.offset	= MTDPART_OFS_APPEND,
-		.size	= MTDPART_SIZ_FULL
-	},
-};
-
-struct platform_nand_data em_x270_nand_platdata = {
-	.chip = {
-		.nr_chips = 1,
-		.chip_offset = 0,
-		.nr_partitions = ARRAY_SIZE(em_x270_partition_info),
-		.partitions = em_x270_partition_info,
-		.chip_delay = 20,
-	},
-	.ctrl = {
-		.dev_ready = em_x270_nand_device_ready,
-		.select_chip = 0,
-		.cmd_ctrl = em_x270_nand_cmd_ctl,
-	},
-};
-
-static struct resource em_x270_nand_resource[] = {
-	[0] = {
-		.start = PXA_CS1_PHYS,
-		.end   = PXA_CS1_PHYS + 12,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device em_x270_nand = {
-	.name		= "gen_nand",
-	.num_resources	= ARRAY_SIZE(em_x270_nand_resource),
-	.resource	= em_x270_nand_resource,
-	.id		= -1,
-	.dev		= {
-		.platform_data = &em_x270_nand_platdata,
-	}
-};
-
-static void __init em_x270_init_nand(void)
-{
-	int err;
-
-	err = gpio_request(GPIO11_NAND_CS, "NAND CS");
-	if (err) {
-		pr_warn("EM-X270: failed to request NAND CS gpio\n");
-		return;
-	}
-
-	gpio_direction_output(GPIO11_NAND_CS, 1);
-
-	err = gpio_request(nand_rb, "NAND R/B");
-	if (err) {
-		pr_warn("EM-X270: failed to request NAND R/B gpio\n");
-		gpio_free(GPIO11_NAND_CS);
-		return;
-	}
-
-	gpio_direction_input(nand_rb);
-
-	platform_device_register(&em_x270_nand);
-}
-#else
-static inline void em_x270_init_nand(void) {}
-#endif
-
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
-static struct mtd_partition em_x270_nor_parts[] = {
-	{
-		.name =		"Bootloader",
-		.offset =	0x00000000,
-		.size =		0x00050000,
-		.mask_flags =	MTD_WRITEABLE  /* force read-only */
-	}, {
-		.name =		"Environment",
-		.offset =	0x00050000,
-		.size =		0x00010000,
-	}, {
-		.name =		"Reserved",
-		.offset =	0x00060000,
-		.size =		0x00050000,
-		.mask_flags =	MTD_WRITEABLE  /* force read-only */
-	}, {
-		.name =		"Splashscreen",
-		.offset =	0x000b0000,
-		.size =		0x00050000,
-	}
-};
-
-static struct physmap_flash_data em_x270_nor_data[] = {
-	[0] = {
-		.width = 2,
-		.parts = em_x270_nor_parts,
-		.nr_parts = ARRAY_SIZE(em_x270_nor_parts),
-	},
-};
-
-static struct resource em_x270_nor_flash_resource = {
-	.start	= PXA_CS0_PHYS,
-	.end	= PXA_CS0_PHYS + SZ_1M - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device em_x270_physmap_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.num_resources	= 1,
-	.resource	= &em_x270_nor_flash_resource,
-	.dev		= {
-		.platform_data	= &em_x270_nor_data,
-	},
-};
-
-static void __init em_x270_init_nor(void)
-{
-	platform_device_register(&em_x270_physmap_flash);
-}
-#else
-static inline void em_x270_init_nor(void) {}
-#endif
-
-/* PXA27x OHCI controller setup */
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static struct regulator *em_x270_usb_ldo;
-
-static int em_x270_usb_hub_init(void)
-{
-	int err;
-
-	em_x270_usb_ldo = regulator_get(NULL, "vcc usb");
-	if (IS_ERR(em_x270_usb_ldo))
-		return PTR_ERR(em_x270_usb_ldo);
-
-	err = gpio_request(GPIO9_USB_VBUS_EN, "vbus en");
-	if (err)
-		goto err_free_usb_ldo;
-
-	err = gpio_request(usb_hub_reset, "hub rst");
-	if (err)
-		goto err_free_vbus_gpio;
-
-	/* USB Hub power-on and reset */
-	gpio_direction_output(usb_hub_reset, 1);
-	gpio_direction_output(GPIO9_USB_VBUS_EN, 0);
-	err = regulator_enable(em_x270_usb_ldo);
-	if (err)
-		goto err_free_rst_gpio;
-
-	gpio_set_value(usb_hub_reset, 0);
-	gpio_set_value(usb_hub_reset, 1);
-	regulator_disable(em_x270_usb_ldo);
-	err = regulator_enable(em_x270_usb_ldo);
-	if (err)
-		goto err_free_rst_gpio;
-
-	gpio_set_value(usb_hub_reset, 0);
-	gpio_set_value(GPIO9_USB_VBUS_EN, 1);
-
-	return 0;
-
-err_free_rst_gpio:
-	gpio_free(usb_hub_reset);
-err_free_vbus_gpio:
-	gpio_free(GPIO9_USB_VBUS_EN);
-err_free_usb_ldo:
-	regulator_put(em_x270_usb_ldo);
-
-	return err;
-}
-
-static int em_x270_ohci_init(struct device *dev)
-{
-	int err;
-
-	/* we don't want to entirely disable USB if the HUB init failed */
-	err = em_x270_usb_hub_init();
-	if (err)
-		pr_err("USB Hub initialization failed: %d\n", err);
-
-	/* enable port 2 transiever */
-	UP2OCR = UP2OCR_HXS | UP2OCR_HXOE;
-
-	return 0;
-}
-
-static void em_x270_ohci_exit(struct device *dev)
-{
-	gpio_free(usb_hub_reset);
-	gpio_free(GPIO9_USB_VBUS_EN);
-
-	if (!IS_ERR(em_x270_usb_ldo)) {
-		if (regulator_is_enabled(em_x270_usb_ldo))
-			regulator_disable(em_x270_usb_ldo);
-
-		regulator_put(em_x270_usb_ldo);
-	}
-}
-
-static struct pxaohci_platform_data em_x270_ohci_platform_data = {
-	.port_mode	= PMM_PERPORT_MODE,
-	.flags		= ENABLE_PORT1 | ENABLE_PORT2 | POWER_CONTROL_LOW,
-	.init		= em_x270_ohci_init,
-	.exit		= em_x270_ohci_exit,
-};
-
-static void __init em_x270_init_ohci(void)
-{
-	pxa_set_ohci_info(&em_x270_ohci_platform_data);
-}
-#else
-static inline void em_x270_init_ohci(void) {}
-#endif
-
-/* MCI controller setup */
-#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
-static struct regulator *em_x270_sdio_ldo;
-
-static struct gpiod_lookup_table em_x270_mci_wp_gpio_table = {
-	.dev_id = "pxa2xx-mci.0",
-	.table = {
-		/* Write protect on GPIO 95 */
-		GPIO_LOOKUP("gpio-pxa", GPIO95_MMC_WP, "wp", GPIO_ACTIVE_LOW),
-		{ },
-	},
-};
-
-static int em_x270_mci_init(struct device *dev,
-			    irq_handler_t em_x270_detect_int,
-			    void *data)
-{
-	int err;
-
-	em_x270_sdio_ldo = regulator_get(dev, "vcc sdio");
-	if (IS_ERR(em_x270_sdio_ldo)) {
-		dev_err(dev, "can't request SDIO power supply: %ld\n",
-			PTR_ERR(em_x270_sdio_ldo));
-		return PTR_ERR(em_x270_sdio_ldo);
-	}
-
-	err = request_irq(gpio_to_irq(mmc_cd), em_x270_detect_int,
-			      IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-			      "MMC card detect", data);
-	if (err) {
-		dev_err(dev, "can't request MMC card detect IRQ: %d\n", err);
-		goto err_irq;
-	}
-
-	if (!machine_is_em_x270()) {
-		err = gpio_request(GPIO38_SD_PWEN, "sdio power");
-		if (err) {
-			dev_err(dev, "can't request MMC power control : %d\n",
-				err);
-			goto err_gpio_wp;
-		}
-		gpio_direction_output(GPIO38_SD_PWEN, 1);
-	}
-
-	return 0;
-
-err_gpio_wp:
-	free_irq(gpio_to_irq(mmc_cd), data);
-err_irq:
-	regulator_put(em_x270_sdio_ldo);
-
-	return err;
-}
-
-static int em_x270_mci_setpower(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data* p_d = dev->platform_data;
-
-	if ((1 << vdd) & p_d->ocr_mask) {
-		int vdd_uV = (2000 + (vdd - __ffs(MMC_VDD_20_21)) * 100) * 1000;
-
-		regulator_set_voltage(em_x270_sdio_ldo, vdd_uV, vdd_uV);
-		return regulator_enable(em_x270_sdio_ldo);
-	} else {
-		regulator_disable(em_x270_sdio_ldo);
-	}
-	return 0;
-}
-
-static void em_x270_mci_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(mmc_cd), data);
-	regulator_put(em_x270_sdio_ldo);
-
-	if (!machine_is_em_x270())
-		gpio_free(GPIO38_SD_PWEN);
-}
-
-static struct pxamci_platform_data em_x270_mci_platform_data = {
-	.detect_delay_ms	= 250,
-	.ocr_mask		= MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
-				  MMC_VDD_24_25|MMC_VDD_25_26|MMC_VDD_26_27|
-				  MMC_VDD_27_28|MMC_VDD_28_29|MMC_VDD_29_30|
-				  MMC_VDD_30_31|MMC_VDD_31_32,
-	.init 			= em_x270_mci_init,
-	.setpower 		= em_x270_mci_setpower,
-	.exit			= em_x270_mci_exit,
-};
-
-static void __init em_x270_init_mmc(void)
-{
-	if (machine_is_em_x270())
-		gpiod_add_lookup_table(&em_x270_mci_wp_gpio_table);
-
-	pxa_set_mci_info(&em_x270_mci_platform_data);
-}
-#else
-static inline void em_x270_init_mmc(void) {}
-#endif
-
-/* LCD */
-#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
-static struct pxafb_mode_info em_x270_lcd_modes[] = {
-	[0] = {
-		.pixclock	= 38250,
-		.bpp		= 16,
-		.xres		= 480,
-		.yres		= 640,
-		.hsync_len	= 8,
-		.vsync_len	= 2,
-		.left_margin	= 8,
-		.upper_margin	= 2,
-		.right_margin	= 24,
-		.lower_margin	= 4,
-		.sync		= 0,
-	},
-	[1] = {
-		.pixclock       = 153800,
-		.bpp		= 16,
-		.xres		= 240,
-		.yres		= 320,
-		.hsync_len	= 8,
-		.vsync_len	= 2,
-		.left_margin	= 8,
-		.upper_margin	= 2,
-		.right_margin	= 88,
-		.lower_margin	= 2,
-		.sync		= 0,
-	},
-};
-
-static struct pxafb_mach_info em_x270_lcd = {
-	.modes		= em_x270_lcd_modes,
-	.num_modes	= 2,
-	.lcd_conn	= LCD_COLOR_TFT_16BPP,
-};
-
-static void __init em_x270_init_lcd(void)
-{
-	pxa_set_fb_info(NULL, &em_x270_lcd);
-}
-#else
-static inline void em_x270_init_lcd(void) {}
-#endif
-
-#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_controller em_x270_spi_info = {
-	.num_chipselect	= 1,
-};
-
-static struct pxa2xx_spi_chip em_x270_tdo24m_chip = {
-	.rx_threshold	= 1,
-	.tx_threshold	= 1,
-	.gpio_cs	= -1,
-};
-
-static struct tdo24m_platform_data em_x270_tdo24m_pdata = {
-	.model = TDO35S,
-};
-
-static struct pxa2xx_spi_controller em_x270_spi_2_info = {
-	.num_chipselect	= 1,
-	.enable_dma	= 1,
-};
-
-static struct pxa2xx_spi_chip em_x270_libertas_chip = {
-	.rx_threshold	= 1,
-	.tx_threshold	= 1,
-	.timeout	= 1000,
-	.gpio_cs	= 14,
-};
-
-static unsigned long em_x270_libertas_pin_config[] = {
-	/* SSP2 */
-	GPIO19_SSP2_SCLK,
-	GPIO14_GPIO,
-	GPIO89_SSP2_TXD,
-	GPIO88_SSP2_RXD,
-};
-
-static int em_x270_libertas_setup(struct spi_device *spi)
-{
-	int err = gpio_request(GPIO115_WLAN_PWEN, "WLAN PWEN");
-	if (err)
-		return err;
-
-	err = gpio_request(GPIO19_WLAN_STRAP, "WLAN STRAP");
-	if (err)
-		goto err_free_pwen;
-
-	if (machine_is_exeda()) {
-		err = gpio_request(GPIO37_WLAN_RST, "WLAN RST");
-		if (err)
-			goto err_free_strap;
-
-		gpio_direction_output(GPIO37_WLAN_RST, 1);
-		msleep(100);
-	}
-
-	gpio_direction_output(GPIO19_WLAN_STRAP, 1);
-	msleep(100);
-
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(em_x270_libertas_pin_config));
-
-	gpio_direction_output(GPIO115_WLAN_PWEN, 0);
-	msleep(100);
-	gpio_set_value(GPIO115_WLAN_PWEN, 1);
-	msleep(100);
-
-	spi->bits_per_word = 16;
-	spi_setup(spi);
-
-	return 0;
-
-err_free_strap:
-	gpio_free(GPIO19_WLAN_STRAP);
-err_free_pwen:
-	gpio_free(GPIO115_WLAN_PWEN);
-
-	return err;
-}
-
-static int em_x270_libertas_teardown(struct spi_device *spi)
-{
-	gpio_set_value(GPIO115_WLAN_PWEN, 0);
-	gpio_free(GPIO115_WLAN_PWEN);
-	gpio_free(GPIO19_WLAN_STRAP);
-
-	if (machine_is_exeda()) {
-		gpio_set_value(GPIO37_WLAN_RST, 0);
-		gpio_free(GPIO37_WLAN_RST);
-	}
-
-	return 0;
-}
-
-struct libertas_spi_platform_data em_x270_libertas_pdata = {
-	.use_dummy_writes	= 1,
-	.setup			= em_x270_libertas_setup,
-	.teardown		= em_x270_libertas_teardown,
-};
-
-static struct spi_board_info em_x270_spi_devices[] __initdata = {
-	{
-		.modalias		= "tdo24m",
-		.max_speed_hz		= 1000000,
-		.bus_num		= 1,
-		.chip_select		= 0,
-		.controller_data	= &em_x270_tdo24m_chip,
-		.platform_data		= &em_x270_tdo24m_pdata,
-	},
-	{
-		.modalias		= "libertas_spi",
-		.max_speed_hz		= 13000000,
-		.bus_num		= 2,
-		.irq			= PXA_GPIO_TO_IRQ(116),
-		.chip_select		= 0,
-		.controller_data	= &em_x270_libertas_chip,
-		.platform_data		= &em_x270_libertas_pdata,
-	},
-};
-
-static void __init em_x270_init_spi(void)
-{
-	pxa2xx_set_spi_info(1, &em_x270_spi_info);
-	pxa2xx_set_spi_info(2, &em_x270_spi_2_info);
-	spi_register_board_info(ARRAY_AND_SIZE(em_x270_spi_devices));
-}
-#else
-static inline void em_x270_init_spi(void) {}
-#endif
-
-#if defined(CONFIG_SND_PXA2XX_LIB_AC97)
-static pxa2xx_audio_ops_t em_x270_ac97_info = {
-	.reset_gpio = 113,
-};
-
-static void __init em_x270_init_ac97(void)
-{
-	pxa_set_ac97_info(&em_x270_ac97_info);
-}
-#else
-static inline void em_x270_init_ac97(void) {}
-#endif
-
-#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE)
-static const unsigned int em_x270_module_matrix_keys[] = {
-	KEY(0, 0, KEY_A), KEY(1, 0, KEY_UP), KEY(2, 1, KEY_B),
-	KEY(0, 2, KEY_LEFT), KEY(1, 1, KEY_ENTER), KEY(2, 0, KEY_RIGHT),
-	KEY(0, 1, KEY_C), KEY(1, 2, KEY_DOWN), KEY(2, 2, KEY_D),
-};
-
-static struct matrix_keymap_data em_x270_matrix_keymap_data = {
-	.keymap			= em_x270_module_matrix_keys,
-	.keymap_size		= ARRAY_SIZE(em_x270_module_matrix_keys),
-};
-
-struct pxa27x_keypad_platform_data em_x270_module_keypad_info = {
-	/* code map for the matrix keys */
-	.matrix_key_rows	= 3,
-	.matrix_key_cols	= 3,
-	.matrix_keymap_data	= &em_x270_matrix_keymap_data,
-};
-
-static const unsigned int em_x270_exeda_matrix_keys[] = {
-	KEY(0, 0, KEY_RIGHTSHIFT), KEY(0, 1, KEY_RIGHTCTRL),
-	KEY(0, 2, KEY_RIGHTALT), KEY(0, 3, KEY_SPACE),
-	KEY(0, 4, KEY_LEFTALT), KEY(0, 5, KEY_LEFTCTRL),
-	KEY(0, 6, KEY_ENTER), KEY(0, 7, KEY_SLASH),
-
-	KEY(1, 0, KEY_DOT), KEY(1, 1, KEY_M),
-	KEY(1, 2, KEY_N), KEY(1, 3, KEY_B),
-	KEY(1, 4, KEY_V), KEY(1, 5, KEY_C),
-	KEY(1, 6, KEY_X), KEY(1, 7, KEY_Z),
-
-	KEY(2, 0, KEY_LEFTSHIFT), KEY(2, 1, KEY_SEMICOLON),
-	KEY(2, 2, KEY_L), KEY(2, 3, KEY_K),
-	KEY(2, 4, KEY_J), KEY(2, 5, KEY_H),
-	KEY(2, 6, KEY_G), KEY(2, 7, KEY_F),
-
-	KEY(3, 0, KEY_D), KEY(3, 1, KEY_S),
-	KEY(3, 2, KEY_A), KEY(3, 3, KEY_TAB),
-	KEY(3, 4, KEY_BACKSPACE), KEY(3, 5, KEY_P),
-	KEY(3, 6, KEY_O), KEY(3, 7, KEY_I),
-
-	KEY(4, 0, KEY_U), KEY(4, 1, KEY_Y),
-	KEY(4, 2, KEY_T), KEY(4, 3, KEY_R),
-	KEY(4, 4, KEY_E), KEY(4, 5, KEY_W),
-	KEY(4, 6, KEY_Q), KEY(4, 7, KEY_MINUS),
-
-	KEY(5, 0, KEY_0), KEY(5, 1, KEY_9),
-	KEY(5, 2, KEY_8), KEY(5, 3, KEY_7),
-	KEY(5, 4, KEY_6), KEY(5, 5, KEY_5),
-	KEY(5, 6, KEY_4), KEY(5, 7, KEY_3),
-
-	KEY(6, 0, KEY_2), KEY(6, 1, KEY_1),
-	KEY(6, 2, KEY_ENTER), KEY(6, 3, KEY_END),
-	KEY(6, 4, KEY_DOWN), KEY(6, 5, KEY_UP),
-	KEY(6, 6, KEY_MENU), KEY(6, 7, KEY_F1),
-
-	KEY(7, 0, KEY_LEFT), KEY(7, 1, KEY_RIGHT),
-	KEY(7, 2, KEY_BACK), KEY(7, 3, KEY_HOME),
-	KEY(7, 4, 0), KEY(7, 5, 0),
-	KEY(7, 6, 0), KEY(7, 7, 0),
-};
-
-static struct matrix_keymap_data em_x270_exeda_matrix_keymap_data = {
-	.keymap			= em_x270_exeda_matrix_keys,
-	.keymap_size		= ARRAY_SIZE(em_x270_exeda_matrix_keys),
-};
-
-struct pxa27x_keypad_platform_data em_x270_exeda_keypad_info = {
-	/* code map for the matrix keys */
-	.matrix_key_rows	= 8,
-	.matrix_key_cols	= 8,
-	.matrix_keymap_data	= &em_x270_exeda_matrix_keymap_data,
-};
-
-static void __init em_x270_init_keypad(void)
-{
-	if (machine_is_em_x270())
-		pxa_set_keypad_info(&em_x270_module_keypad_info);
-	else
-		pxa_set_keypad_info(&em_x270_exeda_keypad_info);
-}
-#else
-static inline void em_x270_init_keypad(void) {}
-#endif
-
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button gpio_keys_button[] = {
-	[0] = {
-		.desc	= "sleep/wakeup",
-		.code	= KEY_SUSPEND,
-		.type	= EV_PWR,
-		.gpio	= 1,
-		.wakeup	= 1,
-	},
-};
-
-static struct gpio_keys_platform_data em_x270_gpio_keys_data = {
-	.buttons	= gpio_keys_button,
-	.nbuttons	= 1,
-};
-
-static struct platform_device em_x270_gpio_keys = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &em_x270_gpio_keys_data,
-	},
-};
-
-static void __init em_x270_init_gpio_keys(void)
-{
-	platform_device_register(&em_x270_gpio_keys);
-}
-#else
-static inline void em_x270_init_gpio_keys(void) {}
-#endif
-
-/* Quick Capture Interface and sensor setup */
-#if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE)
-static int em_x270_sensor_init(void)
-{
-	int ret;
-
-	ret = gpio_request(cam_reset, "camera reset");
-	if (ret)
-		return ret;
-
-	gpio_direction_output(cam_reset, 0);
-	gpio_set_value(cam_reset, 1);
-
-	return 0;
-}
-
-static struct regulator_consumer_supply camera_dummy_supplies[] = {
-	REGULATOR_SUPPLY("vdd", "0-005d"),
-};
-
-static struct regulator_init_data camera_dummy_initdata = {
-	.consumer_supplies = camera_dummy_supplies,
-	.num_consumer_supplies = ARRAY_SIZE(camera_dummy_supplies),
-	.constraints = {
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-};
-
-static struct fixed_voltage_config camera_dummy_config = {
-	.supply_name		= "camera_vdd",
-	.input_supply		= "vcc cam",
-	.microvolts		= 2800000,
-	.init_data		= &camera_dummy_initdata,
-};
-
-static struct platform_device camera_supply_dummy_device = {
-	.name	= "reg-fixed-voltage",
-	.id	= 1,
-	.dev	= {
-		.platform_data = &camera_dummy_config,
-	},
-};
-
-struct pxacamera_platform_data em_x270_camera_platform_data = {
-	.flags  = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 |
-		PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN,
-	.mclk_10khz = 2600,
-	.sensor_i2c_adapter_id = 0,
-	.sensor_i2c_address = 0x5d,
-};
-
-static void  __init em_x270_init_camera(void)
-{
-	if (em_x270_sensor_init() == 0)
-		pxa_set_camera_info(&em_x270_camera_platform_data);
-	platform_device_register(&camera_supply_dummy_device);
-}
-#else
-static inline void em_x270_init_camera(void) {}
-#endif
-
-static struct regulator_bulk_data em_x270_gps_consumer_supply = {
-	.supply		= "vcc gps",
-};
-
-static struct regulator_userspace_consumer_data em_x270_gps_consumer_data = {
-	.name		= "vcc gps",
-	.num_supplies	= 1,
-	.supplies	= &em_x270_gps_consumer_supply,
-};
-
-static struct platform_device em_x270_gps_userspace_consumer = {
-	.name		= "reg-userspace-consumer",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &em_x270_gps_consumer_data,
-	},
-};
-
-static struct regulator_bulk_data em_x270_gprs_consumer_supply = {
-	.supply		= "vcc gprs",
-};
-
-static struct regulator_userspace_consumer_data em_x270_gprs_consumer_data = {
-	.name		= "vcc gprs",
-	.num_supplies	= 1,
-	.supplies	= &em_x270_gprs_consumer_supply
-};
-
-static struct platform_device em_x270_gprs_userspace_consumer = {
-	.name		= "reg-userspace-consumer",
-	.id		= 1,
-	.dev		= {
-		.platform_data = &em_x270_gprs_consumer_data,
-	}
-};
-
-static struct platform_device *em_x270_userspace_consumers[] = {
-	&em_x270_gps_userspace_consumer,
-	&em_x270_gprs_userspace_consumer,
-};
-
-static void __init em_x270_userspace_consumers_init(void)
-{
-	platform_add_devices(ARRAY_AND_SIZE(em_x270_userspace_consumers));
-}
-
-/* DA9030 related initializations */
-#define REGULATOR_CONSUMER(_name, _dev_name, _supply)		        \
-	static struct regulator_consumer_supply _name##_consumers[] = {	\
-		REGULATOR_SUPPLY(_supply, _dev_name),			\
-	}
-
-REGULATOR_CONSUMER(ldo3, "reg-userspace-consumer.0", "vcc gps");
-REGULATOR_CONSUMER(ldo5, NULL, "vcc cam");
-REGULATOR_CONSUMER(ldo10, "pxa2xx-mci", "vcc sdio");
-REGULATOR_CONSUMER(ldo12, NULL, "vcc usb");
-REGULATOR_CONSUMER(ldo19, "reg-userspace-consumer.1", "vcc gprs");
-REGULATOR_CONSUMER(buck2, NULL, "vcc_core");
-
-#define REGULATOR_INIT(_ldo, _min_uV, _max_uV, _ops_mask)		\
-	static struct regulator_init_data _ldo##_data = {		\
-		.constraints = {					\
-			.min_uV = _min_uV,				\
-			.max_uV = _max_uV,				\
-			.state_mem = {					\
-				.enabled = 0,				\
-			},						\
-			.valid_ops_mask = _ops_mask,			\
-			.apply_uV = 1,					\
-		},							\
-		.num_consumer_supplies = ARRAY_SIZE(_ldo##_consumers),	\
-		.consumer_supplies = _ldo##_consumers,			\
-	};
-
-REGULATOR_INIT(ldo3, 3200000, 3200000, REGULATOR_CHANGE_STATUS);
-REGULATOR_INIT(ldo5, 3000000, 3000000, REGULATOR_CHANGE_STATUS);
-REGULATOR_INIT(ldo10, 2000000, 3200000,
-	       REGULATOR_CHANGE_STATUS | REGULATOR_CHANGE_VOLTAGE);
-REGULATOR_INIT(ldo12, 3000000, 3000000, REGULATOR_CHANGE_STATUS);
-REGULATOR_INIT(ldo19, 3200000, 3200000, REGULATOR_CHANGE_STATUS);
-REGULATOR_INIT(buck2, 1000000, 1650000, REGULATOR_CHANGE_VOLTAGE);
-
-struct led_info em_x270_led_info = {
-	.name = "em-x270:orange",
-	.default_trigger = "battery-charging-or-full",
-};
-
-struct power_supply_info em_x270_psy_info = {
-	.name = "battery",
-	.technology = POWER_SUPPLY_TECHNOLOGY_LIPO,
-	.voltage_max_design = 4200000,
-	.voltage_min_design = 3000000,
-	.use_for_apm = 1,
-};
-
-static void em_x270_battery_low(void)
-{
-#if defined(CONFIG_APM_EMULATION)
-	apm_queue_event(APM_LOW_BATTERY);
-#endif
-}
-
-static void em_x270_battery_critical(void)
-{
-#if defined(CONFIG_APM_EMULATION)
-	apm_queue_event(APM_CRITICAL_SUSPEND);
-#endif
-}
-
-struct da9030_battery_info em_x270_batterty_info = {
-	.battery_info = &em_x270_psy_info,
-
-	.charge_milliamp = 1000,
-	.charge_millivolt = 4200,
-
-	.vbat_low = 3600,
-	.vbat_crit = 3400,
-	.vbat_charge_start = 4100,
-	.vbat_charge_stop = 4200,
-	.vbat_charge_restart = 4000,
-
-	.vcharge_min = 3200,
-	.vcharge_max = 5500,
-
-	.tbat_low = 197,
-	.tbat_high = 78,
-	.tbat_restart = 100,
-
-	.batmon_interval = 0,
-
-	.battery_low = em_x270_battery_low,
-	.battery_critical = em_x270_battery_critical,
-};
-
-#define DA9030_SUBDEV(_name, _id, _pdata)	\
-	{					\
-		.name = "da903x-" #_name,	\
-		.id = DA9030_ID_##_id,		\
-		.platform_data = _pdata,	\
-	}
-
-#define DA9030_LDO(num)	DA9030_SUBDEV(regulator, LDO##num, &ldo##num##_data)
-
-struct da903x_subdev_info em_x270_da9030_subdevs[] = {
-	DA9030_LDO(3),
-	DA9030_LDO(5),
-	DA9030_LDO(10),
-	DA9030_LDO(12),
-	DA9030_LDO(19),
-
-	DA9030_SUBDEV(regulator, BUCK2, &buck2_data),
-
-	DA9030_SUBDEV(led, LED_PC, &em_x270_led_info),
-	DA9030_SUBDEV(backlight, WLED, &em_x270_led_info),
-	DA9030_SUBDEV(battery, BAT, &em_x270_batterty_info),
-};
-
-static struct da903x_platform_data em_x270_da9030_info = {
-	.num_subdevs = ARRAY_SIZE(em_x270_da9030_subdevs),
-	.subdevs = em_x270_da9030_subdevs,
-};
-
-static struct i2c_board_info em_x270_i2c_pmic_info = {
-	I2C_BOARD_INFO("da9030", 0x49),
-	.irq = PXA_GPIO_TO_IRQ(0),
-	.platform_data = &em_x270_da9030_info,
-};
-
-static struct i2c_pxa_platform_data em_x270_pwr_i2c_info = {
-	.use_pio = 1,
-};
-
-static void __init em_x270_init_da9030(void)
-{
-	pxa27x_set_i2c_power_info(&em_x270_pwr_i2c_info);
-	i2c_register_board_info(1, &em_x270_i2c_pmic_info, 1);
-}
-
-static struct pca953x_platform_data exeda_gpio_ext_pdata = {
-	.gpio_base = 128,
-};
-
-static struct i2c_board_info exeda_i2c_info[] = {
-	{
-		I2C_BOARD_INFO("pca9555", 0x21),
-		.platform_data = &exeda_gpio_ext_pdata,
-	},
-};
-
-static struct i2c_pxa_platform_data em_x270_i2c_info = {
-	.fast_mode = 1,
-};
-
-static void __init em_x270_init_i2c(void)
-{
-	pxa_set_i2c_info(&em_x270_i2c_info);
-
-	if (machine_is_exeda())
-		i2c_register_board_info(0, ARRAY_AND_SIZE(exeda_i2c_info));
-}
-
-static void __init em_x270_module_init(void)
-{
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(em_x270_pin_config));
-
-	mmc_cd = GPIO13_MMC_CD;
-	nand_rb = GPIO56_NAND_RB;
-	dm9000_flags = DM9000_PLATF_32BITONLY;
-	cam_reset = GPIO93_CAM_RESET;
-	usb_hub_reset = GPIO16_USB_HUB_RESET;
-}
-
-static void __init em_x270_exeda_init(void)
-{
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(exeda_pin_config));
-
-	mmc_cd = GPIO114_MMC_CD;
-	nand_rb = GPIO20_NAND_RB;
-	dm9000_flags = DM9000_PLATF_16BITONLY;
-	cam_reset = GPIO130_CAM_RESET;
-	usb_hub_reset = GPIO10_USB_HUB_RESET;
-}
-
-static void __init em_x270_init(void)
-{
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(common_pin_config));
-
-	pxa_set_ffuart_info(NULL);
-	pxa_set_btuart_info(NULL);
-	pxa_set_stuart_info(NULL);
-
-#ifdef CONFIG_PM
-	pxa27x_set_pwrmode(PWRMODE_DEEPSLEEP);
-#endif
-
-	if (machine_is_em_x270())
-		em_x270_module_init();
-	else if (machine_is_exeda())
-		em_x270_exeda_init();
-	else
-		panic("Unsupported machine: %d\n", machine_arch_type);
-
-	em_x270_init_da9030();
-	em_x270_init_dm9000();
-	em_x270_init_rtc();
-	em_x270_init_nand();
-	em_x270_init_nor();
-	em_x270_init_lcd();
-	em_x270_init_mmc();
-	em_x270_init_ohci();
-	em_x270_init_keypad();
-	em_x270_init_gpio_keys();
-	em_x270_init_ac97();
-	em_x270_init_spi();
-	em_x270_init_i2c();
-	em_x270_init_camera();
-	em_x270_userspace_consumers_init();
-
-	regulator_has_full_constraints();
-}
-
-MACHINE_START(EM_X270, "Compulab EM-X270")
-	.atag_offset	= 0x100,
-	.map_io		= pxa27x_map_io,
-	.nr_irqs	= PXA_NR_IRQS,
-	.init_irq	= pxa27x_init_irq,
-	.handle_irq	= pxa27x_handle_irq,
-	.init_time	= pxa_timer_init,
-	.init_machine	= em_x270_init,
-	.restart	= pxa_restart,
-MACHINE_END
-
-MACHINE_START(EXEDA, "Compulab eXeda")
-	.atag_offset	= 0x100,
-	.map_io		= pxa27x_map_io,
-	.nr_irqs	= PXA_NR_IRQS,
-	.init_irq	= pxa27x_init_irq,
-	.handle_irq	= pxa27x_handle_irq,
-	.init_time	= pxa_timer_init,
-	.init_machine	= em_x270_init,
-	.restart	= pxa_restart,
-MACHINE_END
diff --git a/arch/arm/mach-pxa/include/mach/io.h b/arch/arm/mach-pxa/include/mach/io.h
deleted file mode 100644
index d54031c4f3df..000000000000
--- a/arch/arm/mach-pxa/include/mach/io.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-pxa/include/mach/io.h
- *
- * Copied from asm/arch/sa1100/io.h
- */
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/*
- * We don't actually have real ISA nor PCI buses, but there is so many
- * drivers out there that might just work if we fake them...
- */
-#define __io(a)		__typesafe_io(a)
-
-#endif
-- 
2.26.2


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* [PATCH v2 2/3] MAINTAINERS: pxa: remove Compulab arm/pxa support
  2020-05-20 10:21 [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards Robert Jarzmik
@ 2020-05-20 10:21 ` Robert Jarzmik
  2020-05-20 10:21 ` [PATCH v2 3/3] ASoC: pxa: remove Compulab pxa2xx boards Robert Jarzmik
  2020-05-20 15:21 ` [PATCH v2 1/3] ARM: " Arnd Bergmann
  2 siblings, 0 replies; 15+ messages in thread
From: Robert Jarzmik @ 2020-05-20 10:21 UTC (permalink / raw)
  To: Arnd Bergmann, Miquel Raynal, Boris Brezillon, Mike Rapoport
  Cc: Robert Jarzmik, linux-mtd, linux-arm-kernel

These boards support is removed from the kernel, so remove the
MAINTAINERS entry for them.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
---
 MAINTAINERS | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 091ec22c1a23..ad58388fa822 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1684,11 +1684,6 @@ S:	Maintained
 T:	git git://git.armlinux.org.uk/~rmk/linux-arm.git clkdev
 F:	drivers/clk/clkdev.c
 
-ARM/COMPULAB CM-X270/EM-X270 and CM-X300 MACHINE SUPPORT
-M:	Mike Rapoport <mike@compulab.co.il>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-
 ARM/CONEXANT DIGICOLOR MACHINE SUPPORT
 M:	Baruch Siach <baruch@tkos.co.il>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-- 
2.26.2


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* [PATCH v2 3/3] ASoC: pxa: remove Compulab pxa2xx boards
  2020-05-20 10:21 [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards Robert Jarzmik
  2020-05-20 10:21 ` [PATCH v2 2/3] MAINTAINERS: pxa: remove Compulab arm/pxa support Robert Jarzmik
@ 2020-05-20 10:21 ` Robert Jarzmik
  2020-05-20 13:58   ` Arnd Bergmann
  2020-05-20 15:21 ` [PATCH v2 1/3] ARM: " Arnd Bergmann
  2 siblings, 1 reply; 15+ messages in thread
From: Robert Jarzmik @ 2020-05-20 10:21 UTC (permalink / raw)
  To: Arnd Bergmann, Miquel Raynal, Boris Brezillon, Mike Rapoport
  Cc: Robert Jarzmik, linux-mtd, linux-arm-kernel

As these boards have been removed from the pxa tree, amend accordingly
the sound subsystem.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
---
 sound/soc/pxa/Kconfig | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/sound/soc/pxa/Kconfig b/sound/soc/pxa/Kconfig
index d4c0f580a565..fb2d5ab02b0d 100644
--- a/sound/soc/pxa/Kconfig
+++ b/sound/soc/pxa/Kconfig
@@ -128,9 +128,8 @@ config SND_PXA2XX_SOC_E800
 	  Toshiba e800 PDA
 
 config SND_PXA2XX_SOC_EM_X270
-	tristate "SoC Audio support for CompuLab EM-x270, eXeda and CM-X300"
-	depends on SND_PXA2XX_SOC && (MACH_EM_X270 || MACH_EXEDA || \
-			MACH_CM_X300)
+	tristate "SoC Audio support for CompuLab CM-X300"
+	depends on SND_PXA2XX_SOC && MACH_CM_X300
 	depends on AC97_BUS=n
 	select REGMAP
 	select AC97_BUS_NEW
-- 
2.26.2


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 3/3] ASoC: pxa: remove Compulab pxa2xx boards
  2020-05-20 10:21 ` [PATCH v2 3/3] ASoC: pxa: remove Compulab pxa2xx boards Robert Jarzmik
@ 2020-05-20 13:58   ` Arnd Bergmann
  0 siblings, 0 replies; 15+ messages in thread
From: Arnd Bergmann @ 2020-05-20 13:58 UTC (permalink / raw)
  To: Robert Jarzmik
  Cc: Boris Brezillon, linux-mtd, Mike Rapoport, Linux ARM, Miquel Raynal

On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
>
> As these boards have been removed from the pxa tree, amend accordingly
> the sound subsystem.
>
> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Acked-by: Arnd Bergmann <arnd@arndb.de>

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-20 10:21 [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards Robert Jarzmik
  2020-05-20 10:21 ` [PATCH v2 2/3] MAINTAINERS: pxa: remove Compulab arm/pxa support Robert Jarzmik
  2020-05-20 10:21 ` [PATCH v2 3/3] ASoC: pxa: remove Compulab pxa2xx boards Robert Jarzmik
@ 2020-05-20 15:21 ` Arnd Bergmann
  2020-05-20 15:57   ` Mike Rapoport
  2020-05-21  7:12   ` Mike Rapoport
  2 siblings, 2 replies; 15+ messages in thread
From: Arnd Bergmann @ 2020-05-20 15:21 UTC (permalink / raw)
  To: Robert Jarzmik
  Cc: Boris Brezillon, linux-mtd, Mike Rapoport, Linux ARM, Miquel Raynal

On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
>
> As these boards have no more users nor testers, and patching them has
> become a burden, be that because of the PCI part or the MTD NAND
> support, let's remove them.
>
> The cm-x300 will for now remain and represent Compulab boards at its
> best in the PXA department.
>
> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

Acked-by: Arnd Bergmann <arnd@arndb.de>

Should we take the series through the soc tree? If so, please
send them to soc@kernel.org if there are no objections;
or along with other patches you might have in the pull requests.

      Arnd

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-20 15:21 ` [PATCH v2 1/3] ARM: " Arnd Bergmann
@ 2020-05-20 15:57   ` Mike Rapoport
  2020-05-21  9:01     ` Robert Jarzmik
  2020-05-21  7:12   ` Mike Rapoport
  1 sibling, 1 reply; 15+ messages in thread
From: Mike Rapoport @ 2020-05-20 15:57 UTC (permalink / raw)
  To: Arnd Bergmann
  Cc: linux-mtd, Boris Brezillon, Robert Jarzmik, Linux ARM, Miquel Raynal

On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:
> On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
> >
> > As these boards have no more users nor testers, and patching them has
> > become a burden, be that because of the PCI part or the MTD NAND
> > support, let's remove them.
> >
> > The cm-x300 will for now remain and represent Compulab boards at its
> > best in the PXA department.
> >
> > Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
> 
> Acked-by: Arnd Bergmann <arnd@arndb.de>

I've not been PXA development for a while, so FWIW

Acked-by: Mike Rapoport <rppt@kernel.org>


> Should we take the series through the soc tree? If so, please
> send them to soc@kernel.org if there are no objections;
> or along with other patches you might have in the pull requests.
> 
>       Arnd

-- 
Sincerely yours,
Mike.

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-20 15:21 ` [PATCH v2 1/3] ARM: " Arnd Bergmann
  2020-05-20 15:57   ` Mike Rapoport
@ 2020-05-21  7:12   ` Mike Rapoport
  2020-05-21  7:26     ` Arnd Bergmann
  1 sibling, 1 reply; 15+ messages in thread
From: Mike Rapoport @ 2020-05-21  7:12 UTC (permalink / raw)
  To: Arnd Bergmann
  Cc: linux-mtd, Boris Brezillon, Robert Jarzmik, Linux ARM, Miquel Raynal

On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:
> On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
> >
> > As these boards have no more users nor testers, and patching them has
> > become a burden, be that because of the PCI part or the MTD NAND
> > support, let's remove them.
> >
> > The cm-x300 will for now remain and represent Compulab boards at its
> > best in the PXA department.

I think this series missed the cm-x270 NAND driver, so this could be
PATCH 4/3 (not even compile tested).

From 56a11987f82ef8b32b25dfc17b849f9bbbf03e4d Mon Sep 17 00:00:00 2001
From: Mike Rapoport <rppt@linux.ibm.com>
Date: Thu, 21 May 2020 10:09:47 +0300
Subject: [PATCH] mtd: rawnand: remove CM-X270 NAND driver

The cm-x270 board have been removed and theres is no point to keep this
driver.

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
---
 drivers/mtd/nand/raw/Kconfig       |   4 -
 drivers/mtd/nand/raw/Makefile      |   1 -
 drivers/mtd/nand/raw/cmx270_nand.c | 236 -----------------------------
 3 files changed, 241 deletions(-)
 delete mode 100644 drivers/mtd/nand/raw/cmx270_nand.c

diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index a80a46bb5b8b..9b08a58ae88e 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -213,10 +213,6 @@ config MTD_NAND_MLC_LPC32XX
 	  Please check the actual NAND chip connected and its support
 	  by the MLC NAND controller.
 
-config MTD_NAND_CM_X270
-	tristate "CM-X270 modules NAND controller"
-	depends on MACH_ARMCORE
-
 config MTD_NAND_PASEMI
 	tristate "PA Semi PWRficient NAND controller"
 	depends on PPC_PASEMI
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
index 2d136b158fb7..a817052286c7 100644
--- a/drivers/mtd/nand/raw/Makefile
+++ b/drivers/mtd/nand/raw/Makefile
@@ -25,7 +25,6 @@ obj-$(CONFIG_MTD_NAND_GPIO)		+= gpio.o
 omap2_nand-objs := omap2.o
 obj-$(CONFIG_MTD_NAND_OMAP2) 		+= omap2_nand.o
 obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD)	+= omap_elm.o
-obj-$(CONFIG_MTD_NAND_CM_X270)		+= cmx270_nand.o
 obj-$(CONFIG_MTD_NAND_MARVELL)		+= marvell_nand.o
 obj-$(CONFIG_MTD_NAND_TMIO)		+= tmio_nand.o
 obj-$(CONFIG_MTD_NAND_PLATFORM)		+= plat_nand.o
diff --git a/drivers/mtd/nand/raw/cmx270_nand.c b/drivers/mtd/nand/raw/cmx270_nand.c
deleted file mode 100644
index 045b6175ae79..000000000000
--- a/drivers/mtd/nand/raw/cmx270_nand.c
+++ /dev/null
@@ -1,236 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  Copyright (C) 2006 Compulab, Ltd.
- *  Mike Rapoport <mike@compulab.co.il>
- *
- *  Derived from drivers/mtd/nand/h1910.c (removed in v3.10)
- *       Copyright (C) 2002 Marius Gröger (mag@sysgo.de)
- *       Copyright (c) 2001 Thomas Gleixner (gleixner@autronix.de)
- *
- *  Overview:
- *   This is a device driver for the NAND flash device found on the
- *   CM-X270 board.
- */
-
-#include <linux/mtd/rawnand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/slab.h>
-#include <linux/gpio.h>
-#include <linux/module.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/mach-types.h>
-
-#include <mach/pxa2xx-regs.h>
-
-#define GPIO_NAND_CS	(11)
-#define GPIO_NAND_RB	(89)
-
-/* MTD structure for CM-X270 board */
-static struct mtd_info *cmx270_nand_mtd;
-
-/* remaped IO address of the device */
-static void __iomem *cmx270_nand_io;
-
-/*
- * Define static partitions for flash device
- */
-static const struct mtd_partition partition_info[] = {
-	[0] = {
-		.name	= "cmx270-0",
-		.offset	= 0,
-		.size	= MTDPART_SIZ_FULL
-	}
-};
-#define NUM_PARTITIONS (ARRAY_SIZE(partition_info))
-
-static u_char cmx270_read_byte(struct nand_chip *this)
-{
-	return (readl(this->legacy.IO_ADDR_R) >> 16);
-}
-
-static void cmx270_write_buf(struct nand_chip *this, const u_char *buf,
-			     int len)
-{
-	int i;
-
-	for (i=0; i<len; i++)
-		writel((*buf++ << 16), this->legacy.IO_ADDR_W);
-}
-
-static void cmx270_read_buf(struct nand_chip *this, u_char *buf, int len)
-{
-	int i;
-
-	for (i=0; i<len; i++)
-		*buf++ = readl(this->legacy.IO_ADDR_R) >> 16;
-}
-
-static inline void nand_cs_on(void)
-{
-	gpio_set_value(GPIO_NAND_CS, 0);
-}
-
-static void nand_cs_off(void)
-{
-	dsb();
-
-	gpio_set_value(GPIO_NAND_CS, 1);
-}
-
-/*
- *	hardware specific access to control-lines
- */
-static void cmx270_hwcontrol(struct nand_chip *this, int dat,
-			     unsigned int ctrl)
-{
-	unsigned int nandaddr = (unsigned int)this->legacy.IO_ADDR_W;
-
-	dsb();
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		if ( ctrl & NAND_ALE )
-			nandaddr |=  (1 << 3);
-		else
-			nandaddr &= ~(1 << 3);
-		if ( ctrl & NAND_CLE )
-			nandaddr |=  (1 << 2);
-		else
-			nandaddr &= ~(1 << 2);
-		if ( ctrl & NAND_NCE )
-			nand_cs_on();
-		else
-			nand_cs_off();
-	}
-
-	dsb();
-	this->legacy.IO_ADDR_W = (void __iomem*)nandaddr;
-	if (dat != NAND_CMD_NONE)
-		writel((dat << 16), this->legacy.IO_ADDR_W);
-
-	dsb();
-}
-
-/*
- *	read device ready pin
- */
-static int cmx270_device_ready(struct nand_chip *this)
-{
-	dsb();
-
-	return (gpio_get_value(GPIO_NAND_RB));
-}
-
-/*
- * Main initialization routine
- */
-static int __init cmx270_init(void)
-{
-	struct nand_chip *this;
-	int ret;
-
-	if (!(machine_is_armcore() && cpu_is_pxa27x()))
-		return -ENODEV;
-
-	ret = gpio_request(GPIO_NAND_CS, "NAND CS");
-	if (ret) {
-		pr_warn("CM-X270: failed to request NAND CS gpio\n");
-		return ret;
-	}
-
-	gpio_direction_output(GPIO_NAND_CS, 1);
-
-	ret = gpio_request(GPIO_NAND_RB, "NAND R/B");
-	if (ret) {
-		pr_warn("CM-X270: failed to request NAND R/B gpio\n");
-		goto err_gpio_request;
-	}
-
-	gpio_direction_input(GPIO_NAND_RB);
-
-	/* Allocate memory for MTD device structure and private data */
-	this = kzalloc(sizeof(struct nand_chip), GFP_KERNEL);
-	if (!this) {
-		ret = -ENOMEM;
-		goto err_kzalloc;
-	}
-
-	cmx270_nand_io = ioremap(PXA_CS1_PHYS, 12);
-	if (!cmx270_nand_io) {
-		pr_debug("Unable to ioremap NAND device\n");
-		ret = -EINVAL;
-		goto err_ioremap;
-	}
-
-	cmx270_nand_mtd = nand_to_mtd(this);
-
-	/* Link the private data with the MTD structure */
-	cmx270_nand_mtd->owner = THIS_MODULE;
-
-	/* insert callbacks */
-	this->legacy.IO_ADDR_R = cmx270_nand_io;
-	this->legacy.IO_ADDR_W = cmx270_nand_io;
-	this->legacy.cmd_ctrl = cmx270_hwcontrol;
-	this->legacy.dev_ready = cmx270_device_ready;
-
-	/* 15 us command delay time */
-	this->legacy.chip_delay = 20;
-	this->ecc.mode = NAND_ECC_SOFT;
-	this->ecc.algo = NAND_ECC_HAMMING;
-
-	/* read/write functions */
-	this->legacy.read_byte = cmx270_read_byte;
-	this->legacy.read_buf = cmx270_read_buf;
-	this->legacy.write_buf = cmx270_write_buf;
-
-	/* Scan to find existence of the device */
-	ret = nand_scan(this, 1);
-	if (ret) {
-		pr_notice("No NAND device\n");
-		goto err_scan;
-	}
-
-	/* Register the partitions */
-	ret = mtd_device_register(cmx270_nand_mtd, partition_info,
-				  NUM_PARTITIONS);
-	if (ret)
-		goto err_scan;
-
-	/* Return happy */
-	return 0;
-
-err_scan:
-	iounmap(cmx270_nand_io);
-err_ioremap:
-	kfree(this);
-err_kzalloc:
-	gpio_free(GPIO_NAND_RB);
-err_gpio_request:
-	gpio_free(GPIO_NAND_CS);
-
-	return ret;
-
-}
-module_init(cmx270_init);
-
-/*
- * Clean up routine
- */
-static void __exit cmx270_cleanup(void)
-{
-	/* Release resources, unregister device */
-	nand_release(mtd_to_nand(cmx270_nand_mtd));
-
-	gpio_free(GPIO_NAND_RB);
-	gpio_free(GPIO_NAND_CS);
-
-	iounmap(cmx270_nand_io);
-
-	kfree(mtd_to_nand(cmx270_nand_mtd));
-}
-module_exit(cmx270_cleanup);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Mike Rapoport <mike@compulab.co.il>");
-MODULE_DESCRIPTION("NAND flash driver for Compulab CM-X270 Module");
-- 
2.25.2



> > Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
> 
> Acked-by: Arnd Bergmann <arnd@arndb.de>
> 
> Should we take the series through the soc tree? If so, please
> send them to soc@kernel.org if there are no objections;
> or along with other patches you might have in the pull requests.
> 
>       Arnd

-- 
Sincerely yours,
Mike.

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-21  7:12   ` Mike Rapoport
@ 2020-05-21  7:26     ` Arnd Bergmann
  2020-05-21 19:01       ` Mike Rapoport
  0 siblings, 1 reply; 15+ messages in thread
From: Arnd Bergmann @ 2020-05-21  7:26 UTC (permalink / raw)
  To: Mike Rapoport
  Cc: linux-mtd, Boris Brezillon, Robert Jarzmik, Linux ARM, Miquel Raynal

On Thu, May 21, 2020 at 9:12 AM Mike Rapoport <rppt@kernel.org> wrote:
>
> On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:
> > On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
> > >
> > > As these boards have no more users nor testers, and patching them has
> > > become a burden, be that because of the PCI part or the MTD NAND
> > > support, let's remove them.
> > >
> > > The cm-x300 will for now remain and represent Compulab boards at its
> > > best in the PXA department.
>
> I think this series missed the cm-x270 NAND driver, so this could be
> PATCH 4/3 (not even compile tested).
>
> From 56a11987f82ef8b32b25dfc17b849f9bbbf03e4d Mon Sep 17 00:00:00 2001
> From: Mike Rapoport <rppt@linux.ibm.com>
> Date: Thu, 21 May 2020 10:09:47 +0300
> Subject: [PATCH] mtd: rawnand: remove CM-X270 NAND driver
>
> The cm-x270 board have been removed and theres is no point to keep this
> driver.
>
> Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>

Thanks! Removing that driver was actually how the discussion started,
so we definitely want to do that. Boris earlier patch "mtd: rawnand: Get
rid of the cmx270 driver" did it by changing the board file, now your
patch is the right thing to do, and we should remember to do the same
for mbxfb.

      Arnd

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-20 15:57   ` Mike Rapoport
@ 2020-05-21  9:01     ` Robert Jarzmik
  0 siblings, 0 replies; 15+ messages in thread
From: Robert Jarzmik @ 2020-05-21  9:01 UTC (permalink / raw)
  To: Mike Rapoport
  Cc: Boris Brezillon, linux-mtd, Linux ARM, Arnd Bergmann, Miquel Raynal

Mike Rapoport <rppt@kernel.org> writes:

> On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:
>> On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
>> >
>> > As these boards have no more users nor testers, and patching them has
>> > become a burden, be that because of the PCI part or the MTD NAND
>> > support, let's remove them.
>> >
>> > The cm-x300 will for now remain and represent Compulab boards at its
>> > best in the PXA department.
>> >
>> > Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
>> 
>> Acked-by: Arnd Bergmann <arnd@arndb.de>
>
> I've not been PXA development for a while, so FWIW
>
> Acked-by: Mike Rapoport <rppt@kernel.org>
>
>
>> Should we take the series through the soc tree? If so, please
>> send them to soc@kernel.org if there are no objections;
>> or along with other patches you might have in the pull requests.
Yeah, that would be great. I'll send it to soc@kernel.org, adding the 2 acks I
>> got (which make it a v3).

Cheers.

--
Robert

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-21  7:26     ` Arnd Bergmann
@ 2020-05-21 19:01       ` Mike Rapoport
  2020-05-21 19:10         ` Boris Brezillon
  0 siblings, 1 reply; 15+ messages in thread
From: Mike Rapoport @ 2020-05-21 19:01 UTC (permalink / raw)
  To: Arnd Bergmann
  Cc: linux-mtd, Boris Brezillon, Robert Jarzmik, Linux ARM, Miquel Raynal

On Thu, May 21, 2020 at 09:26:10AM +0200, Arnd Bergmann wrote:
> On Thu, May 21, 2020 at 9:12 AM Mike Rapoport <rppt@kernel.org> wrote:
> >
> > On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:
> > > On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
> > > >
> > > > As these boards have no more users nor testers, and patching them has
> > > > become a burden, be that because of the PCI part or the MTD NAND
> > > > support, let's remove them.
> > > >
> > > > The cm-x300 will for now remain and represent Compulab boards at its
> > > > best in the PXA department.
> >
> > I think this series missed the cm-x270 NAND driver, so this could be
> > PATCH 4/3 (not even compile tested).
> >
> > From 56a11987f82ef8b32b25dfc17b849f9bbbf03e4d Mon Sep 17 00:00:00 2001
> > From: Mike Rapoport <rppt@linux.ibm.com>
> > Date: Thu, 21 May 2020 10:09:47 +0300
> > Subject: [PATCH] mtd: rawnand: remove CM-X270 NAND driver
> >
> > The cm-x270 board have been removed and theres is no point to keep this
> > driver.
> >
> > Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
> 
> Thanks! Removing that driver was actually how the discussion started,
> so we definitely want to do that. Boris earlier patch "mtd: rawnand: Get
> rid of the cmx270 driver" did it by changing the board file, now your
> patch is the right thing to do, and we should remember to do the same
> for mbxfb.

Arnd, will you pick this to the SoC tree or should I resend?

>       Arnd

-- 
Sincerely yours,
Mike.

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-21 19:01       ` Mike Rapoport
@ 2020-05-21 19:10         ` Boris Brezillon
  2020-05-22 11:18           ` Miquel Raynal
  0 siblings, 1 reply; 15+ messages in thread
From: Boris Brezillon @ 2020-05-21 19:10 UTC (permalink / raw)
  To: Mike Rapoport
  Cc: linux-mtd, Robert Jarzmik, Linux ARM, Arnd Bergmann, Miquel Raynal

On Thu, 21 May 2020 22:01:58 +0300
Mike Rapoport <rppt@kernel.org> wrote:

> On Thu, May 21, 2020 at 09:26:10AM +0200, Arnd Bergmann wrote:
> > On Thu, May 21, 2020 at 9:12 AM Mike Rapoport <rppt@kernel.org> wrote:  
> > >
> > > On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:  
> > > > On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:  
> > > > >
> > > > > As these boards have no more users nor testers, and patching them has
> > > > > become a burden, be that because of the PCI part or the MTD NAND
> > > > > support, let's remove them.
> > > > >
> > > > > The cm-x300 will for now remain and represent Compulab boards at its
> > > > > best in the PXA department.  
> > >
> > > I think this series missed the cm-x270 NAND driver, so this could be
> > > PATCH 4/3 (not even compile tested).
> > >
> > > From 56a11987f82ef8b32b25dfc17b849f9bbbf03e4d Mon Sep 17 00:00:00 2001
> > > From: Mike Rapoport <rppt@linux.ibm.com>
> > > Date: Thu, 21 May 2020 10:09:47 +0300
> > > Subject: [PATCH] mtd: rawnand: remove CM-X270 NAND driver
> > >
> > > The cm-x270 board have been removed and theres is no point to keep this
> > > driver.
> > >
> > > Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>  
> > 
> > Thanks! Removing that driver was actually how the discussion started,
> > so we definitely want to do that. Boris earlier patch "mtd: rawnand: Get
> > rid of the cmx270 driver" did it by changing the board file, now your
> > patch is the right thing to do, and we should remember to do the same
> > for mbxfb.  
> 
> Arnd, will you pick this to the SoC tree or should I resend?

Actually I sent a v2 removing only the MTD driver. You should probably
sync with Miquel to make sure the same patch is not applied twice.

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-21 19:10         ` Boris Brezillon
@ 2020-05-22 11:18           ` Miquel Raynal
  2020-05-22 13:14             ` Arnd Bergmann
  0 siblings, 1 reply; 15+ messages in thread
From: Miquel Raynal @ 2020-05-22 11:18 UTC (permalink / raw)
  To: Boris Brezillon
  Cc: Linux ARM, linux-mtd, Robert Jarzmik, Arnd Bergmann, Mike Rapoport

Hello,

Boris Brezillon <boris.brezillon@collabora.com> wrote on Thu, 21 May
2020 21:10:16 +0200:

> On Thu, 21 May 2020 22:01:58 +0300
> Mike Rapoport <rppt@kernel.org> wrote:
> 
> > On Thu, May 21, 2020 at 09:26:10AM +0200, Arnd Bergmann wrote:  
> > > On Thu, May 21, 2020 at 9:12 AM Mike Rapoport <rppt@kernel.org> wrote:    
> > > >
> > > > On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:    
> > > > > On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:    
> > > > > >
> > > > > > As these boards have no more users nor testers, and patching them has
> > > > > > become a burden, be that because of the PCI part or the MTD NAND
> > > > > > support, let's remove them.
> > > > > >
> > > > > > The cm-x300 will for now remain and represent Compulab boards at its
> > > > > > best in the PXA department.    
> > > >
> > > > I think this series missed the cm-x270 NAND driver, so this could be
> > > > PATCH 4/3 (not even compile tested).
> > > >
> > > > From 56a11987f82ef8b32b25dfc17b849f9bbbf03e4d Mon Sep 17 00:00:00 2001
> > > > From: Mike Rapoport <rppt@linux.ibm.com>
> > > > Date: Thu, 21 May 2020 10:09:47 +0300
> > > > Subject: [PATCH] mtd: rawnand: remove CM-X270 NAND driver
> > > >
> > > > The cm-x270 board have been removed and theres is no point to keep this
> > > > driver.
> > > >
> > > > Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>    
> > > 
> > > Thanks! Removing that driver was actually how the discussion started,
> > > so we definitely want to do that. Boris earlier patch "mtd: rawnand: Get
> > > rid of the cmx270 driver" did it by changing the board file, now your
> > > patch is the right thing to do, and we should remember to do the same
> > > for mbxfb.    
> > 
> > Arnd, will you pick this to the SoC tree or should I resend?  
> 
> Actually I sent a v2 removing only the MTD driver. You should probably
> sync with Miquel to make sure the same patch is not applied twice.

Actually I was about the merge this patch in the MTD tree because I
have a big cleanup series which depends on it. Arnd could you confirm
that it's okay for you?


Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-22 11:18           ` Miquel Raynal
@ 2020-05-22 13:14             ` Arnd Bergmann
  2020-05-22 13:17               ` Miquel Raynal
  0 siblings, 1 reply; 15+ messages in thread
From: Arnd Bergmann @ 2020-05-22 13:14 UTC (permalink / raw)
  To: Miquel Raynal
  Cc: linux-mtd, Boris Brezillon, Robert Jarzmik, Linux ARM, Mike Rapoport

On Fri, May 22, 2020 at 1:18 PM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> Boris Brezillon <boris.brezillon@collabora.com> wrote on Thu, 21 May
> 2020 21:10:16 +0200:
>
> > On Thu, 21 May 2020 22:01:58 +0300
> > Mike Rapoport <rppt@kernel.org> wrote:
> >
> > > On Thu, May 21, 2020 at 09:26:10AM +0200, Arnd Bergmann wrote:
> > > > On Thu, May 21, 2020 at 9:12 AM Mike Rapoport <rppt@kernel.org> wrote:
> > > > >
> > > > > On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:
> > > > > > On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:
> > > > > > >
> > > > > > > As these boards have no more users nor testers, and patching them has
> > > > > > > become a burden, be that because of the PCI part or the MTD NAND
> > > > > > > support, let's remove them.
> > > > > > >
> > > > > > > The cm-x300 will for now remain and represent Compulab boards at its
> > > > > > > best in the PXA department.
> > > > >
> > > > > I think this series missed the cm-x270 NAND driver, so this could be
> > > > > PATCH 4/3 (not even compile tested).
> > > > >
> > > > > From 56a11987f82ef8b32b25dfc17b849f9bbbf03e4d Mon Sep 17 00:00:00 2001
> > > > > From: Mike Rapoport <rppt@linux.ibm.com>
> > > > > Date: Thu, 21 May 2020 10:09:47 +0300
> > > > > Subject: [PATCH] mtd: rawnand: remove CM-X270 NAND driver
> > > > >
> > > > > The cm-x270 board have been removed and theres is no point to keep this
> > > > > driver.
> > > > >
> > > > > Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
> > > >
> > > > Thanks! Removing that driver was actually how the discussion started,
> > > > so we definitely want to do that. Boris earlier patch "mtd: rawnand: Get
> > > > rid of the cmx270 driver" did it by changing the board file, now your
> > > > patch is the right thing to do, and we should remember to do the same
> > > > for mbxfb.
> > >
> > > Arnd, will you pick this to the SoC tree or should I resend?
> >
> > Actually I sent a v2 removing only the MTD driver. You should probably
> > sync with Miquel to make sure the same patch is not applied twice.
>
> Actually I was about the merge this patch in the MTD tree because I
> have a big cleanup series which depends on it. Arnd could you confirm
> that it's okay for you?

Yes, that sounds good. I assume the patch is basically identical to the one
that Mike just sent, right? If there are changes to arch/arm, I guess those can
be dropped now as I'm merging Robert's patches to remove those board
files.

      Arnd

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-22 13:14             ` Arnd Bergmann
@ 2020-05-22 13:17               ` Miquel Raynal
  2020-05-22 13:22                 ` Arnd Bergmann
  0 siblings, 1 reply; 15+ messages in thread
From: Miquel Raynal @ 2020-05-22 13:17 UTC (permalink / raw)
  To: Arnd Bergmann
  Cc: linux-mtd, Boris Brezillon, Robert Jarzmik, Linux ARM, Mike Rapoport

Hi Arnd,

Arnd Bergmann <arnd@arndb.de> wrote on Fri, 22 May 2020 15:14:43 +0200:

> On Fri, May 22, 2020 at 1:18 PM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> > Boris Brezillon <boris.brezillon@collabora.com> wrote on Thu, 21 May
> > 2020 21:10:16 +0200:
> >  
> > > On Thu, 21 May 2020 22:01:58 +0300
> > > Mike Rapoport <rppt@kernel.org> wrote:
> > >  
> > > > On Thu, May 21, 2020 at 09:26:10AM +0200, Arnd Bergmann wrote:  
> > > > > On Thu, May 21, 2020 at 9:12 AM Mike Rapoport <rppt@kernel.org> wrote:  
> > > > > >
> > > > > > On Wed, May 20, 2020 at 05:21:51PM +0200, Arnd Bergmann wrote:  
> > > > > > > On Wed, May 20, 2020 at 12:21 PM Robert Jarzmik <robert.jarzmik@free.fr> wrote:  
> > > > > > > >
> > > > > > > > As these boards have no more users nor testers, and patching them has
> > > > > > > > become a burden, be that because of the PCI part or the MTD NAND
> > > > > > > > support, let's remove them.
> > > > > > > >
> > > > > > > > The cm-x300 will for now remain and represent Compulab boards at its
> > > > > > > > best in the PXA department.  
> > > > > >
> > > > > > I think this series missed the cm-x270 NAND driver, so this could be
> > > > > > PATCH 4/3 (not even compile tested).
> > > > > >
> > > > > > From 56a11987f82ef8b32b25dfc17b849f9bbbf03e4d Mon Sep 17 00:00:00 2001
> > > > > > From: Mike Rapoport <rppt@linux.ibm.com>
> > > > > > Date: Thu, 21 May 2020 10:09:47 +0300
> > > > > > Subject: [PATCH] mtd: rawnand: remove CM-X270 NAND driver
> > > > > >
> > > > > > The cm-x270 board have been removed and theres is no point to keep this
> > > > > > driver.
> > > > > >
> > > > > > Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>  
> > > > >
> > > > > Thanks! Removing that driver was actually how the discussion started,
> > > > > so we definitely want to do that. Boris earlier patch "mtd: rawnand: Get
> > > > > rid of the cmx270 driver" did it by changing the board file, now your
> > > > > patch is the right thing to do, and we should remember to do the same
> > > > > for mbxfb.  
> > > >
> > > > Arnd, will you pick this to the SoC tree or should I resend?  
> > >
> > > Actually I sent a v2 removing only the MTD driver. You should probably
> > > sync with Miquel to make sure the same patch is not applied twice.  
> >
> > Actually I was about the merge this patch in the MTD tree because I
> > have a big cleanup series which depends on it. Arnd could you confirm
> > that it's okay for you?  
> 
> Yes, that sounds good. I assume the patch is basically identical to the one
> that Mike just sent, right? If there are changes to arch/arm, I guess those can
> be dropped now as I'm merging Robert's patches to remove those board
> files.
> 
>       Arnd

Here is the diffstat:

 drivers/mtd/nand/raw/Kconfig       |   4 -
 drivers/mtd/nand/raw/Makefile      |   1 -
 drivers/mtd/nand/raw/cmx270_nand.c | 236 -----------------------------
 3 files changed, 241 deletions(-)
 delete mode 100644 drivers/mtd/nand/raw/cmx270_nand.c

So it should be fine.

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

* Re: [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards
  2020-05-22 13:17               ` Miquel Raynal
@ 2020-05-22 13:22                 ` Arnd Bergmann
  0 siblings, 0 replies; 15+ messages in thread
From: Arnd Bergmann @ 2020-05-22 13:22 UTC (permalink / raw)
  To: Miquel Raynal
  Cc: linux-mtd, Boris Brezillon, Robert Jarzmik, Linux ARM, Mike Rapoport

On Fri, May 22, 2020 at 3:17 PM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> Arnd Bergmann <arnd@arndb.de> wrote on Fri, 22 May 2020 15:14:43 +0200:
>
> > On Fri, May 22, 2020 at 1:18 PM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> > > Boris Brezillon <boris.brezillon@collabora.com> wrote on Thu, 21 May

> > > Actually I was about the merge this patch in the MTD tree because I
> > > have a big cleanup series which depends on it. Arnd could you confirm
> > > that it's okay for you?
> >
> > Yes, that sounds good. I assume the patch is basically identical to the one
> > that Mike just sent, right? If there are changes to arch/arm, I guess those can
> > be dropped now as I'm merging Robert's patches to remove those board
> > files.
> >
> >       Arnd
>
> Here is the diffstat:
>
>  drivers/mtd/nand/raw/Kconfig       |   4 -
>  drivers/mtd/nand/raw/Makefile      |   1 -
>  drivers/mtd/nand/raw/cmx270_nand.c | 236 -----------------------------
>  3 files changed, 241 deletions(-)
>  delete mode 100644 drivers/mtd/nand/raw/cmx270_nand.c
>
> So it should be fine.

Agreed, please apply it.

     Arnd

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 15+ messages in thread

end of thread, back to index

Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-20 10:21 [PATCH v2 1/3] ARM: pxa: remove Compulab pxa2xx boards Robert Jarzmik
2020-05-20 10:21 ` [PATCH v2 2/3] MAINTAINERS: pxa: remove Compulab arm/pxa support Robert Jarzmik
2020-05-20 10:21 ` [PATCH v2 3/3] ASoC: pxa: remove Compulab pxa2xx boards Robert Jarzmik
2020-05-20 13:58   ` Arnd Bergmann
2020-05-20 15:21 ` [PATCH v2 1/3] ARM: " Arnd Bergmann
2020-05-20 15:57   ` Mike Rapoport
2020-05-21  9:01     ` Robert Jarzmik
2020-05-21  7:12   ` Mike Rapoport
2020-05-21  7:26     ` Arnd Bergmann
2020-05-21 19:01       ` Mike Rapoport
2020-05-21 19:10         ` Boris Brezillon
2020-05-22 11:18           ` Miquel Raynal
2020-05-22 13:14             ` Arnd Bergmann
2020-05-22 13:17               ` Miquel Raynal
2020-05-22 13:22                 ` Arnd Bergmann

Linux-mtd Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-mtd/0 linux-mtd/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-mtd linux-mtd/ https://lore.kernel.org/linux-mtd \
		linux-mtd@lists.infradead.org
	public-inbox-index linux-mtd

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-mtd


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git