Re: [v5 1/2] mtd: nand: Add new Cadence NAND driver to MTD subsystem

[Dmitry Osipenko <digetx@gmail.com>]

Hello Miquèl,

24.08.2019 13:49, Miquel Raynal пишет:
> Hi Dmitry,
> 
> Dmitry Osipenko <digetx@gmail.com> wrote on Thu, 25 Jul 2019 18:11:43
> +0300:
> 
>> 25.07.2019 18:00, Piotr Sroka пишет:
>>> Add new Cadence NAND driver to MTD subsystem
>>>
>>> Signed-off-by: Piotr Sroka <piotrs@cadence.com>
>>> ---
>>> Changes for v5:
>>> - fix "ecc config strength" field size
>>> - remove unused macros
>>> - fix address of timing2 register
>>> - add guard for accessing data_control_size register
>>> - simplify the driver by use the same function 
>>>   for accessing main area and oob area
>>> - add comment to the driver describing main controller modes
>>> - change compatible name from cdns,hpnfc to cdns,hp-nfc
>>> Changes for v4:
>>> - fix comments issues like typos, missing capitals, missing dots etc.
>>> - remove unnecessary PHY options phy_dll_aging and phy_per_bit_deskew
>>> - replace all register access functions to "relaxed" version
>>> - remove all unnecessary variables initializations
>>> - handle error inside cadence_nand_get_ecc_strength_idx function in case 
>>>   correnction strength is not found
>>> - add commit message
>>> Changes for v3:
>>> - remove definitions of unused registers
>>> - remove configuring registers which are not expected to be configured in
>>>   asynchronous mode
>>> - remove not needed function reading timing registers
>>> - remove information about oob size and write size from cdns_nand_chip type
>>>   and use vales from mtd_info directly
>>> - use nand_cleanup instead of nand_release if mtd device is not registered yet
>>> - fix cadence_nand_chips_init function add garbage collection 
>>>   if a chip init fails
>>> - simplify PHY calculations
>>> Changes for v2:
>>> - create one universal wait function for all events instead of one
>>>   function per event.
>>> - split one big function executing nand operations to separate
>>>   functions one per each type of operation.
>>> - add erase atomic operation to nand operation parser
>>> - remove unnecessary includes.
>>> - remove unused register defines 
>>> - add support for multiple nand chips
>>> - remove all code using legacy functions
>>> - remove chip dependents parameters from dts bindings, they were
>>>   attached to the SoC specific compatible at the driver level
>>> - simplify interrupt handling
>>> - simplify timing calculations
>>> - fix calculation of maximum supported cs signals
>>> - simplify ecc size calculation
>>> - remove header file and put whole code to one c file
>>> ---
>>>  drivers/mtd/nand/raw/Kconfig                   |    7 +
>>>  drivers/mtd/nand/raw/Makefile                  |    1 +
>>>  drivers/mtd/nand/raw/cadence-nand-controller.c | 3021 ++++++++++++++++++++++++
>>>  3 files changed, 3029 insertions(+)
>>>  create mode 100644 drivers/mtd/nand/raw/cadence-nand-controller.c
>>>
>>> diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
>>> index e604625e2dfa..4d2ce3b5b2ae 100644
>>> --- a/drivers/mtd/nand/raw/Kconfig
>>> +++ b/drivers/mtd/nand/raw/Kconfig
>>> @@ -557,5 +557,12 @@ config MTD_NAND_MESON
>>>  	help
>>>  	  Enables support for NAND controller on Amlogic's Meson SoCs.
>>>  	  This controller is found on Meson SoCs.
>>> +config MTD_NAND_CADENCE
>>> +	tristate "Support Cadence NAND (HPNFC) controller"
>>> +	depends on OF
>>> +	help
>>> +	  Enable the driver for NAND flash on platforms using a Cadence NAND
>>> +	  controller.
>>> +
>>>  
>>>  endif # MTD_NAND
>>> diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
>>> index 5a5a72f0793e..f4b099f276f7 100644
>>> --- a/drivers/mtd/nand/raw/Makefile
>>> +++ b/drivers/mtd/nand/raw/Makefile
>>> @@ -58,6 +58,7 @@ obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
>>>  obj-$(CONFIG_MTD_NAND_TEGRA)		+= tegra_nand.o
>>>  obj-$(CONFIG_MTD_NAND_STM32_FMC2)	+= stm32_fmc2_nand.o
>>>  obj-$(CONFIG_MTD_NAND_MESON)		+= meson_nand.o
>>> +obj-$(CONFIG_MTD_NAND_CADENCE)		+= cadence-nand-controller.o
>>>  
>>>  nand-objs := nand_base.o nand_legacy.o nand_bbt.o nand_timings.o nand_ids.o
>>>  nand-objs += nand_onfi.o
>>> diff --git a/drivers/mtd/nand/raw/cadence-nand-controller.c b/drivers/mtd/nand/raw/cadence-nand-controller.c
>>> new file mode 100644
>>> index 000000000000..a7ff4e4585d3
>>> --- /dev/null
>>> +++ b/drivers/mtd/nand/raw/cadence-nand-controller.c
>>> @@ -0,0 +1,3021 @@
>>> +// SPDX-License-Identifier: GPL-2.0+
>>> +/*
>>> + * Cadence NAND flash controller driver
>>> + *
>>> + * Copyright (C) 2019 Cadence
>>> + */
>>> +
>>> +#include <linux/bitfield.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/dma-mapping.h>
>>> +#include <linux/dmaengine.h>
>>> +#include <linux/interrupt.h>
>>> +#include <linux/module.h>
>>> +#include <linux/mtd/mtd.h>
>>> +#include <linux/mtd/rawnand.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/iopoll.h>
>>> +
>>> +/*
>>> + * HPNFC can work in 3 modes:
>>> + * -  PIO - can work in master or slave DMA.
>>> + * -  CDMA - needs Master DMA for accessing command descriptors.
>>> + * -  Generic mode - can use only slave DMA.
>>> + * CDMA and PIO modes can be used to execute only base commands.
>>> + * Generic mode can be used to execute any command
>>> + * on NAND flash memory. Driver uses CDMA mode for
>>> + * block erasing, page reading, page programing.
>>> + * Generic mode is used for executing rest of commands.
>>> + */
>>> +
>>> +#define MAX_OOB_SIZE_PER_SECTOR	32
>>> +#define MAX_ADDRESS_CYC		6
>>> +#define MAX_ERASE_ADDRESS_CYC	3
>>> +#define MAX_DATA_SIZE		0xFFFC
>>> +
>>> +/* Register definition. */
>>> +/*
>>> + * Command register 0.
>>> + * Writing data to this register will initiate a new transaction
>>> + * of the NF controller.
>>> + */
>>> +#define CMD_REG0			0x0000
>>> +/* Command type field mask. */
>>> +#define		CMD_REG0_CT		GENMASK(31, 30)
>>> +/* Command type CDMA. */
>>> +#define		CMD_REG0_CT_CDMA	0uL
>>> +/* Command type generic. */
>>> +#define		CMD_REG0_CT_GEN		3uL
>>> +/* Command thread number field mask. */
>>> +#define		CMD_REG0_TN		GENMASK(27, 24)
>>> +
>>> +/* Command register 2. */
>>> +#define CMD_REG2			0x0008
>>> +/* Command register 3. */
>>> +#define CMD_REG3			0x000C
>>> +/* Pointer register to select which thread status will be selected. */
>>> +#define CMD_STATUS_PTR			0x0010
>>> +/* Command status register for selected thread. */
>>> +#define CMD_STATUS			0x0014
>>> +
>>> +/* Interrupt status register. */
>>> +#define INTR_STATUS			0x0110
>>> +#define		INTR_STATUS_SDMA_ERR	BIT(22)
>>> +#define		INTR_STATUS_SDMA_TRIGG	BIT(21)
>>> +#define		INTR_STATUS_UNSUPP_CMD	BIT(19)
>>> +#define		INTR_STATUS_DDMA_TERR	BIT(18)
>>> +#define		INTR_STATUS_CDMA_TERR	BIT(17)
>>> +#define		INTR_STATUS_CDMA_IDL	BIT(16)
>>> +
>>> +/* Interrupt enable register. */
>>> +#define INTR_ENABLE				0x0114
>>> +#define		INTR_ENABLE_INTR_EN		BIT(31)
>>> +#define		INTR_ENABLE_SDMA_ERR_EN		BIT(22)
>>> +#define		INTR_ENABLE_SDMA_TRIGG_EN	BIT(21)
>>> +#define		INTR_ENABLE_UNSUPP_CMD_EN	BIT(19)
>>> +#define		INTR_ENABLE_DDMA_TERR_EN	BIT(18)
>>> +#define		INTR_ENABLE_CDMA_TERR_EN	BIT(17)
>>> +#define		INTR_ENABLE_CDMA_IDLE_EN	BIT(16)
>>> +
>>> +/* Controller internal state. */
>>> +#define CTRL_STATUS				0x0118
>>> +#define		CTRL_STATUS_INIT_COMP		BIT(9)
>>> +#define		CTRL_STATUS_CTRL_BUSY		BIT(8)
>>> +
>>> +/* Command Engine threads state. */
>>> +#define TRD_STATUS				0x0120
>>> +
>>> +/* Command Engine interrupt thread error status. */
>>> +#define TRD_ERR_INT_STATUS			0x0128
>>> +/* Command Engine interrupt thread error enable. */
>>> +#define TRD_ERR_INT_STATUS_EN			0x0130
>>> +/* Command Engine interrupt thread complete status. */
>>> +#define TRD_COMP_INT_STATUS			0x0138
>>> +
>>> +/*
>>> + * Transfer config 0 register.
>>> + * Configures data transfer parameters.
>>> + */
>>> +#define TRAN_CFG_0				0x0400
>>> +/* Offset value from the beginning of the page. */
>>> +#define		TRAN_CFG_0_OFFSET		GENMASK(31, 16)
>>> +/* Numbers of sectors to transfer within singlNF device's page. */
>>> +#define		TRAN_CFG_0_SEC_CNT		GENMASK(7, 0)
>>> +
>>> +/*
>>> + * Transfer config 1 register.
>>> + * Configures data transfer parameters.
>>> + */
>>> +#define TRAN_CFG_1				0x0404
>>> +/* Size of last data sector. */
>>> +#define		TRAN_CFG_1_LAST_SEC_SIZE	GENMASK(31, 16)
>>> +/* Size of not-last data sector. */
>>> +#define		TRAN_CFG_1_SECTOR_SIZE		GENMASK(15, 0)
>>> +
>>> +/* ECC engine configuration register 0. */
>>> +#define ECC_CONFIG_0				0x0428
>>> +/* Correction strength. */
>>> +#define		ECC_CONFIG_0_CORR_STR		GENMASK(10, 8)
>>> +/* Enable erased pages detection mechanism. */
>>> +#define		ECC_CONFIG_0_ERASE_DET_EN	BIT(1)
>>> +/* Enable controller ECC check bits generation and correction. */
>>> +#define		ECC_CONFIG_0_ECC_EN		BIT(0)
>>> +
>>> +/* ECC engine configuration register 1. */
>>> +#define ECC_CONFIG_1				0x042C
>>> +
>>> +/* Multiplane settings register. */
>>> +#define MULTIPLANE_CFG				0x0434
>>> +/* Cache operation settings. */
>>> +#define CACHE_CFG				0x0438
>>> +
>>> +/* DMA settings register. */
>>> +#define DMA_SETINGS				0x043C
>>> +/* Enable SDMA error report on access unprepared slave DMA interface. */
>>> +#define		DMA_SETINGS_SDMA_ERR_RSP	BIT(17)
>>> +
>>> +/* Transferred data block size for the slave DMA module. */
>>> +#define SDMA_SIZE				0x0440
>>> +
>>> +/* Thread number associated with transferred data block
>>> + * for the slave DMA module.
>>> + */
>>> +#define SDMA_TRD_NUM				0x0444
>>> +/* Thread number mask. */
>>> +#define		SDMA_TRD_NUM_SDMA_TRD		GENMASK(2, 0)
>>> +
>>> +#define CONTROL_DATA_CTRL			0x0494
>>> +/* Thread number mask. */
>>> +#define		CONTROL_DATA_CTRL_SIZE		GENMASK(15, 0)
>>> +
>>> +#define CTRL_VERSION				0x800
>>> +
>>> +/* Available hardware features of the controller. */
>>> +#define CTRL_FEATURES				0x804
>>> +/* Support for NV-DDR2/3 work mode. */
>>> +#define		CTRL_FEATURES_NVDDR_2_3		BIT(28)
>>> +/* Support for NV-DDR work mode. */
>>> +#define		CTRL_FEATURES_NVDDR		BIT(27)
>>> +/* Support for asynchronous work mode. */
>>> +#define		CTRL_FEATURES_ASYNC		BIT(26)
>>> +/* Support for asynchronous work mode. */
>>> +#define		CTRL_FEATURES_N_BANKS		GENMASK(25, 24)
>>> +/* Slave and Master DMA data width. */
>>> +#define		CTRL_FEATURES_DMA_DWITH64	BIT(21)
>>> +/* Availability of Control Data feature.*/
>>> +#define		CTRL_FEATURES_CONTROL_DATA	BIT(10)
>>> +
>>> +/* BCH Engine identification register 0 - correction strengths. */
>>> +#define BCH_CFG_0				0x838
>>> +#define		BCH_CFG_0_CORR_CAP_0		GENMASK(7, 0)
>>> +#define		BCH_CFG_0_CORR_CAP_1		GENMASK(15, 8)
>>> +#define		BCH_CFG_0_CORR_CAP_2		GENMASK(23, 16)
>>> +#define		BCH_CFG_0_CORR_CAP_3		GENMASK(31, 24)
>>> +
>>> +/* BCH Engine identification register 1 - correction strengths. */
>>> +#define BCH_CFG_1				0x83C
>>> +#define		BCH_CFG_1_CORR_CAP_4		GENMASK(7, 0)
>>> +#define		BCH_CFG_1_CORR_CAP_5		GENMASK(15, 8)
>>> +#define		BCH_CFG_1_CORR_CAP_6		GENMASK(23, 16)
>>> +#define		BCH_CFG_1_CORR_CAP_7		GENMASK(31, 24)
>>> +
>>> +/* BCH Engine identification register 2 - sector sizes. */
>>> +#define BCH_CFG_2				0x840
>>> +#define		BCH_CFG_2_SECT_0		GENMASK(15, 0)
>>> +#define		BCH_CFG_2_SECT_1		GENMASK(31, 16)
>>> +
>>> +/* BCH Engine identification register 3. */
>>> +#define BCH_CFG_3				0x844
>>> +
>>> +/* Ready/Busy# line status. */
>>> +#define RBN_SETINGS				0x1004
>>> +
>>> +/* Common settings. */
>>> +#define COMMON_SET				0x1008
>>> +/* 16 bit device connected to the NAND Flash interface. */
>>> +#define		COMMON_SET_DEVICE_16BIT		BIT(8)
>>> +
>>> +/* Skip_bytes registers. */
>>> +#define SKIP_BYTES_CONF				0x100C
>>> +#define		SKIP_BYTES_MARKER_VALUE		GENMASK(31, 16)
>>> +#define		SKIP_BYTES_NUM_OF_BYTES		GENMASK(7, 0)
>>> +
>>> +#define SKIP_BYTES_OFFSET			0x1010
>>> +#define		 SKIP_BYTES_OFFSET_VALUE	GENMASK(23, 0)
>>> +
>>> +/* Timings configuration. */
>>> +#define ASYNC_TOGGLE_TIMINGS			0x101c
>>> +#define		ASYNC_TOGGLE_TIMINGS_TRH	GENMASK(28, 24)
>>> +#define		ASYNC_TOGGLE_TIMINGS_TRP	GENMASK(20, 16)
>>> +#define		ASYNC_TOGGLE_TIMINGS_TWH	GENMASK(12, 8)
>>> +#define		ASYNC_TOGGLE_TIMINGS_TWP	GENMASK(4, 0)
>>> +
>>> +#define	TIMINGS0				0x1024
>>> +#define		TIMINGS0_TADL			GENMASK(31, 24)
>>> +#define		TIMINGS0_TCCS			GENMASK(23, 16)
>>> +#define		TIMINGS0_TWHR			GENMASK(15, 8)
>>> +#define		TIMINGS0_TRHW			GENMASK(7, 0)
>>> +
>>> +#define	TIMINGS1				0x1028
>>> +#define		TIMINGS1_TRHZ			GENMASK(31, 24)
>>> +#define		TIMINGS1_TWB			GENMASK(23, 16)
>>> +#define		TIMINGS1_TVDLY			GENMASK(7, 0)
>>> +
>>> +#define	TIMINGS2				0x102c
>>> +#define		TIMINGS2_TFEAT			GENMASK(25, 16)
>>> +#define		TIMINGS2_CS_HOLD_TIME		GENMASK(13, 8)
>>> +#define		TIMINGS2_CS_SETUP_TIME		GENMASK(5, 0)
>>> +
>>> +/* Configuration of the resynchronization of slave DLL of PHY. */
>>> +#define DLL_PHY_CTRL				0x1034
>>> +#define		DLL_PHY_CTRL_DLL_RST_N		BIT(24)
>>> +#define		DLL_PHY_CTRL_EXTENDED_WR_MODE	BIT(17)
>>> +#define		DLL_PHY_CTRL_EXTENDED_RD_MODE	BIT(16)
>>> +#define		DLL_PHY_CTRL_RS_HIGH_WAIT_CNT	GENMASK(11, 8)
>>> +#define		DLL_PHY_CTRL_RS_IDLE_CNT	GENMASK(7, 0)
>>> +
>>> +/* Register controlling DQ related timing. */
>>> +#define PHY_DQ_TIMING				0x2000
>>> +/* Register controlling DSQ related timing.  */
>>> +#define PHY_DQS_TIMING				0x2004
>>> +#define		PHY_DQS_TIMING_DQS_SEL_OE_END	GENMASK(3, 0)
>>> +#define		PHY_DQS_TIMING_PHONY_DQS_SEL	BIT(16)
>>> +#define		PHY_DQS_TIMING_USE_PHONY_DQS	BIT(20)
>>> +
>>> +/* Register controlling the gate and loopback control related timing. */
>>> +#define PHY_GATE_LPBK_CTRL			0x2008
>>> +#define		PHY_GATE_LPBK_CTRL_RDS		GENMASK(24, 19)
>>> +
>>> +/* Register holds the control for the master DLL logic. */
>>> +#define PHY_DLL_MASTER_CTRL			0x200C
>>> +#define		PHY_DLL_MASTER_CTRL_BYPASS_MODE	BIT(23)
>>> +
>>> +/* Register holds the control for the slave DLL logic. */
>>> +#define PHY_DLL_SLAVE_CTRL			0x2010
>>> +
>>> +/* This register handles the global control settings for the PHY. */
>>> +#define PHY_CTRL				0x2080
>>> +#define		PHY_CTRL_SDR_DQS		BIT(14)
>>> +#define		PHY_CTRL_PHONY_DQS		GENMASK(9, 4)
>>> +
>>> +/*
>>> + * This register handles the global control settings
>>> + * for the termination selects for reads.
>>> + */
>>> +#define PHY_TSEL				0x2084
>>> +
>>> +/* Generic command layout. */
>>> +#define GCMD_LAY_CS			GENMASK_ULL(11, 8)
>>> +/*
>>> + * This bit informs the minicotroller if it has to wait for tWB
>>> + * after sending the last CMD/ADDR/DATA in the sequence.
>>> + */
>>> +#define GCMD_LAY_TWB			BIT_ULL(6)
>>> +/* Type of generic instruction. */
>>> +#define GCMD_LAY_INSTR			GENMASK_ULL(5, 0)
>>> +
>>> +/* Generic CMD sequence type. */
>>> +#define		GCMD_LAY_INSTR_CMD	0
>>> +/* Generic ADDR sequence type. */
>>> +#define		GCMD_LAY_INSTR_ADDR	1
>>> +/* Generic data transfer sequence type. */
>>> +#define		GCMD_LAY_INSTR_DATA	2
>>> +
>>> +/* Input part of generic command type of input is command. */
>>> +#define GCMD_LAY_INPUT_CMD		GENMASK_ULL(23, 16)
>>> +
>>> +/* Generic command address sequence - address fields. */
>>> +#define GCMD_LAY_INPUT_ADDR		GENMASK_ULL(63, 16)
>>> +/* Generic command address sequence - address size. */
>>> +#define GCMD_LAY_INPUT_ADDR_SIZE	GENMASK_ULL(13, 11)
>>> +
>>> +/* Transfer direction field of generic command data sequence. */
>>> +#define GCMD_DIR			BIT_ULL(11)
>>> +/* Read transfer direction of generic command data sequence. */
>>> +#define		GCMD_DIR_READ		0
>>> +/* Write transfer direction of generic command data sequence. */
>>> +#define		GCMD_DIR_WRITE		1
>>> +
>>> +/* ECC enabled flag of generic command data sequence - ECC enabled. */
>>> +#define GCMD_ECC_EN			BIT_ULL(12)
>>> +/* Generic command data sequence - sector size. */
>>> +#define GCMD_SECT_SIZE			GENMASK_ULL(31, 16)
>>> +/* Generic command data sequence - sector count. */
>>> +#define GCMD_SECT_CNT			GENMASK_ULL(39, 32)
>>> +/* Generic command data sequence - last sector size. */
>>> +#define GCMD_LAST_SIZE			GENMASK_ULL(55, 40)
>>> +
>>> +/* CDMA descriptor fields. */
>>> +/* Erase command type of CDMA descriptor. */
>>> +#define CDMA_CT_ERASE		0x1000
>>> +/* Program page command type of CDMA descriptor. */
>>> +#define CDMA_CT_WR		0x2100
>>> +/* Read page command type of CDMA descriptor. */
>>> +#define CDMA_CT_RD		0x2200
>>> +
>>> +/* Flash pointer memory shift. */
>>> +#define CDMA_CFPTR_MEM_SHIFT	24
>>> +/* Flash pointer memory mask. */
>>> +#define CDMA_CFPTR_MEM		GENMASK(26, 24)
>>> +
>>> +/*
>>> + * Command DMA descriptor flags. If set causes issue interrupt after
>>> + * the completion of descriptor processing.
>>> + */
>>> +#define CDMA_CF_INT		BIT(8)
>>> +/*
>>> + * Command DMA descriptor flags - the next descriptor
>>> + * address field is valid and descriptor processing should continue.
>>> + */
>>> +#define CDMA_CF_CONT		BIT(9)
>>> +/* DMA master flag of command DMA descriptor. */
>>> +#define CDMA_CF_DMA_MASTER	BIT(10)
>>> +
>>> +/* Operation complete status of command descriptor. */
>>> +#define CDMA_CS_COMP		BIT(15)
>>> +/* Operation complete status of command descriptor. */
>>> +/* Command descriptor status - operation fail. */
>>> +#define CDMA_CS_FAIL		BIT(14)
>>> +/* Command descriptor status - page erased. */
>>> +#define CDMA_CS_ERP		BIT(11)
>>> +/* Command descriptor status - timeout occurred. */
>>> +#define CDMA_CS_TOUT		BIT(10)
>>> +/*
>>> + * Maximum amount of correction applied to one ECC sector.
>>> + * It is part of command descriptor status.
>>> + */
>>> +#define CDMA_CS_MAXERR		GENMASK(9, 2)
>>> +/* Command descriptor status - uncorrectable ECC error. */
>>> +#define CDMA_CS_UNCE		BIT(1)
>>> +/* Command descriptor status - descriptor error. */
>>> +#define CDMA_CS_ERR		BIT(0)
>>> +
>>> +/* Status of operation - OK. */
>>> +#define STAT_OK			0
>>> +/* Status of operation - FAIL. */
>>> +#define STAT_FAIL		2
>>> +/* Status of operation - uncorrectable ECC error. */
>>> +#define STAT_ECC_UNCORR		3
>>> +/* Status of operation - page erased. */
>>> +#define STAT_ERASED		5
>>> +/* Status of operation - correctable ECC error. */
>>> +#define STAT_ECC_CORR		6
>>> +/* Status of operation - unsuspected state. */
>>> +#define STAT_UNKNOWN		7
>>> +/* Status of operation - operation is not completed yet. */
>>> +#define STAT_BUSY		0xFF
>>> +
>>> +#define BCH_MAX_NUM_CORR_CAPS		8
>>> +#define BCH_MAX_NUM_SECTOR_SIZES	2
>>> +
>>> +struct cadence_nand_timings {
>>> +	u32 async_toggle_timings;
>>> +	u32 timings0;
>>> +	u32 timings1;
>>> +	u32 timings2;
>>> +	u32 dll_phy_ctrl;
>>> +	u32 phy_ctrl;
>>> +	u32 phy_dqs_timing;
>>> +	u32 phy_gate_lpbk_ctrl;
>>> +};
>>> +
>>> +/* Command DMA descriptor. */
>>> +struct cadence_nand_cdma_desc {
>>> +	/* Next descriptor address. */
>>> +	u64 next_pointer;
>>> +
>>> +	/* Flash address is a 32-bit address comprising of BANK and ROW ADDR. */
>>> +	u32 flash_pointer;
>>> +	u32 rsvd0;
>>> +
>>> +	/* Operation the controller needs to perform. */
>>> +	u16 command_type;
>>> +	u16 rsvd1;
>>> +	/* Flags for operation of this command. */
>>> +	u16 command_flags;
>>> +	u16 rsvd2;
>>> +
>>> +	/* System/host memory address required for data DMA commands. */
>>> +	u64 memory_pointer;
>>> +
>>> +	/* Status of operation. */
>>> +	u32 status;
>>> +	u32 rsvd3;
>>> +
>>> +	/* Address pointer to sync buffer location. */
>>> +	u64 sync_flag_pointer;
>>> +
>>> +	/* Controls the buffer sync mechanism. */
>>> +	u32 sync_arguments;
>>> +	u32 rsvd4;
>>> +
>>> +	/* Control data pointer. */
>>> +	u64 ctrl_data_ptr;
>>> +};
>>> +
>>> +/* Interrupt status. */
>>> +struct cadence_nand_irq_status {
>>> +	/* Thread operation complete status. */
>>> +	u32 trd_status;
>>> +	/* Thread operation error. */
>>> +	u32 trd_error;
>>> +	/* Controller status. */
>>> +	u32 status;
>>> +};
>>> +
>>> +/* Cadence NAND flash controller capabilities get from driver data. */
>>> +struct cadence_nand_dt_devdata {
>>> +	/* Skew value of the output signals of the NAND Flash interface. */
>>> +	u32 if_skew;
>>> +	/* It informs if slave DMA interface is connected to DMA engine. */
>>> +	unsigned int has_dma:1;
>>> +};
>>> +
>>> +/* Cadence NAND flash controller capabilities read from registers. */
>>> +struct cdns_nand_caps {
>>> +	/* Maximum number of banks supported by hardware. */
>>> +	u8 max_banks;
>>> +	/* Slave and Master DMA data width in bytes (4 or 8). */
>>> +	u8 data_dma_width;
>>> +	/* Control Data feature supported. */
>>> +	u8 data_control_supp;
>>> +	/* Is PHY type DLL. */
>>> +	u8 is_phy_type_dll;  
>>
>> I'd make 'data_control_supp' and 'is_phy_type_dll' u8:1 or unsigned
>> int:1 as you did for 'has_dma', for consistency.
> 
> Or just booleans. I know under certain circumstances it can be badly
> handled but I don't think we care here.

Agree!

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/