From: Greg Ungerer <gerg@kernel.org>
To: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>,
Miquel Raynal <miquel.raynal@bootlin.com>
Cc: s.hauer@pengutronix.de, linux-mtd@lists.infradead.org
Subject: Re: GPMI iMX6ull timeout on DMA
Date: Mon, 29 Jul 2019 22:18:36 +1000 [thread overview]
Message-ID: <ec14d017-1274-c7ea-f0b2-6c20dc07360e@kernel.org> (raw)
In-Reply-To: <CAOf5uwk+iWmEk07b+RW3W1b1c0vjfhZVJwKpV_LZJofLNtBsug@mail.gmail.com>
Hi Michael,
On 29/7/19 6:42 pm, Michael Nazzareno Trimarchi wrote:
> Hi all
>
> On Mon, Jul 29, 2019 at 10:36 AM Miquel Raynal
> <miquel.raynal@bootlin.com> wrote:
>>
>> Hi Greg,
>>
>> One question below.
>>
>> +Michael
>> +Sascha
>>
>> Hello Michael, here is a similar issue to yours, I know you did not
>> have enough time to share your solution but here we have someone else
>> reproducing the issue, would you mind sharing a branch or a patch, even
>> a WIP one, just to help debugging?
>>
>
> I have patches reverted as I mention in the email. The step to
> reproduce is simple.
>
> Just reboot every successful boot.
Testing like this how often does it occur?
Regards
Greg
> Michael
>
>> Greg Ungerer <gerg@kernel.org> wrote on Mon, 29 Jul 2019 16:41:51 +1000:
>>
>>> Hi Miquel,
>>>
>>> I am experiencing a problem with NAND flash DMA timeouts on
>>> iMX6ull based boards. The problem is very similar to that
>>> described in:
>>>
>>> https://linux-mtd.infradead.narkive.com/JIUulfFB/gpmi-imx6ull-timeout-on-dma
>>>
>>> That didn't come to any specific resolution that I could see
>>> in that thread.
>>>
>>> The boot trace on the console for me looks like this:
>>>
>>> nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
>>> nand: Micron MT29F2G08ABAEAWP
>>> nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
>>> gpmi-nand 1806000.gpmi-nand: DMA timeout, last DMA
>>> gpmi-nand 1806000.gpmi-nand: Show GPMI registers :
>>> gpmi-nand 1806000.gpmi-nand: offset 0x000 : 0x20830002
>>> gpmi-nand 1806000.gpmi-nand: offset 0x010 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x020 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x030 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x040 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x050 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x060 : 0x01c6800c
>>> gpmi-nand 1806000.gpmi-nand: offset 0x070 : 0x00010101
>>> gpmi-nand 1806000.gpmi-nand: offset 0x080 : 0xe0000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x090 : 0x23023336
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0a0 : 0x000001ee
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0b0 : 0xff000001
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0c0 : 0x00000001
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0d0 : 0x05020000
>>> gpmi-nand 1806000.gpmi-nand: Show BCH registers :
>>> gpmi-nand 1806000.gpmi-nand: offset 0x000 : 0x00000100
>>> gpmi-nand 1806000.gpmi-nand: offset 0x010 : 0x00000010
>>> gpmi-nand 1806000.gpmi-nand: offset 0x020 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x030 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x040 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x050 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x060 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x070 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x080 : 0x030a2080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x090 : 0x083e2080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0a0 : 0x070a4080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0b0 : 0x10da4080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0c0 : 0x070a4080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0d0 : 0x10da4080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0e0 : 0x070a4080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x0f0 : 0x10da4080
>>> gpmi-nand 1806000.gpmi-nand: offset 0x100 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x110 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x120 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x130 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x140 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x150 : 0x20484342
>>> gpmi-nand 1806000.gpmi-nand: offset 0x160 : 0x01000000
>>> gpmi-nand 1806000.gpmi-nand: offset 0x170 : 0x00000000
>>> gpmi-nand 1806000.gpmi-nand: BCH Geometry :
>>> GF length : 13
>>> ECC Strength : 8
>>> Page Size in Bytes : 2110
>>> Metadata Size in Bytes : 10
>>> ECC Chunk0 Size in Bytes: 512
>>> ECC Chunkn Size in Bytes: 512
>>> ECC Chunk Count : 4
>>> Payload Size in Bytes : 2048
>>> Auxiliary Size in Bytes: 16
>>> Auxiliary Status Offset: 12
>>> Block Mark Byte Offset : 1999
>>> Block Mark Bit Offset : 0
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -110
>>> nand: timing mode 5 not acknowledged by the NAND chip
>>
>> What is the final timing mode used? Most of us tested in mode 5 I
>> guess, maybe mode 4 is broken (don't know if this is the one used here,
>> neither why mode 5 is refused). Can you please try by limiting the mode
>> to 0, 1, 2... until, hopefully, we narrow down to the failing mode.
>>
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> Scanning device for bad blocks
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> ....
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> gpmi-nand 1806000.gpmi-nand: Chip: 0, Error -22
>>> 5 fixed-partitions partitions found on MTD device gpmi-nand
>>> Creating 5 MTD partitions on "gpmi-nand":
>>> 0x000000000000-0x000000500000 : "u-boot"
>>> 0x000000500000-0x000000600000 : "u-boot-env"
>>> 0x000000600000-0x000000800000 : "log"
>>> 0x000000800000-0x000010000000 : "flash"
>>> 0x000000000000-0x000010000000 : "all"
>>> gpmi-nand 1806000.gpmi-nand: driver registered.
>>>
>>>
>>> This is using a linux kernel v5.1.14. I have seen this happen on
>>> a number of boards I have here - but it is only occasional. It
>>> only happens once in a while on boot, maybe 1 in 40 or more times.
>>> So it can take quite a while to reproduce (using a boot loop setup).
>>
>> That's strange... I don't get what would produce such unstable issue.
>>
>>>
>>> As per the email thread I pointed to above I looked at reverting
>>> those patches, but that was not at all easy given how much the gpmi
>>> driver code had moved. So instead I modified the code with this:
>>>
>>> --- a/linux/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
>>> +++ b/linux/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
>>> @@ -481,6 +481,7 @@ static void gpmi_nfc_compute_timings(struct gpmi_nand_data *this,
>>> void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
>>> {
>>> +#if 0
>>> struct gpmi_nfc_hardware_timing *hw = &this->hw;
>>> struct resources *r = &this->resources;
>>> void __iomem *gpmi_regs = r->gpmi_regs;
>>> @@ -505,6 +512,7 @@ void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
>>> /* Wait for the DLL to settle. */
>>> udelay(dll_wait_time_us);
>>> +#endif
>>> }
>>> int gpmi_setup_data_interface(struct nand_chip *chip, int chipnr,
>>>
>>> So far after a couple of days of testing with this I no longer
>>> see the DMA timeout.
>>>
>>> Any thoughts?
>>>
>>> Regards
>>> Greg
>>>
>>
>> Thanks,
>> Miquèl
>
>
>
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2019-07-29 12:19 UTC|newest]
Thread overview: 85+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-07-29 6:41 GPMI iMX6ull timeout on DMA Greg Ungerer
2019-07-29 8:36 ` Miquel Raynal
2019-07-29 8:42 ` Michael Nazzareno Trimarchi
2019-07-29 12:18 ` Greg Ungerer [this message]
2019-07-29 12:20 ` Michael Nazzareno Trimarchi
2019-07-29 12:33 ` Greg Ungerer
2019-07-29 12:47 ` Miquel Raynal
2019-07-29 12:49 ` Michael Nazzareno Trimarchi
2019-07-29 12:55 ` Miquel Raynal
2019-07-29 13:00 ` Michael Nazzareno Trimarchi
2019-07-29 13:22 ` Miquel Raynal
2019-07-29 20:00 ` Michael Nazzareno Trimarchi
2019-07-29 21:02 ` Miquel Raynal
2019-07-30 0:28 ` Greg Ungerer
2019-07-30 0:41 ` Greg Ungerer
2019-07-30 6:06 ` Greg Ungerer
2019-07-30 8:38 ` Miquel Raynal
2019-07-30 8:58 ` Boris Brezillon
2019-07-31 2:05 ` Greg Ungerer
2019-07-31 6:28 ` Boris Brezillon
2019-08-02 7:19 ` Greg Ungerer
2019-08-02 12:34 ` Greg Ungerer
2019-08-02 12:51 ` Boris Brezillon
2019-08-05 5:51 ` Greg Ungerer
2019-08-07 16:05 ` Miquel Raynal
2019-08-08 0:43 ` Greg Ungerer
2019-08-08 16:36 ` Boris Brezillon
2019-08-09 5:20 ` Greg Ungerer
2019-08-09 6:23 ` Boris Brezillon
2019-08-09 6:55 ` Greg Ungerer
2019-08-09 7:32 ` Boris Brezillon
2019-08-09 13:57 ` Greg Ungerer
2019-08-09 13:59 ` Boris Brezillon
2019-08-12 2:50 ` Greg Ungerer
2019-08-12 4:04 ` Greg Ungerer
2019-08-12 7:31 ` Boris Brezillon
2019-08-13 0:50 ` Greg Ungerer
2021-01-28 9:45 ` Michael Nazzareno Trimarchi
2021-01-28 10:26 ` Miquel Raynal
2021-01-28 10:35 ` Michael Nazzareno Trimarchi
2021-01-28 11:55 ` Michael Nazzareno Trimarchi
2021-01-29 12:43 ` Greg Ungerer
2021-01-30 9:41 ` Michael Nazzareno Trimarchi
2021-02-01 14:13 ` Miquel Raynal
2021-02-01 14:32 ` Michael Nazzareno Trimarchi
2021-02-01 15:08 ` Michael Nazzareno Trimarchi
2021-02-01 15:14 ` Miquel Raynal
2021-02-01 15:17 ` Michael Nazzareno Trimarchi
2021-10-15 20:05 ` Michael Trimarchi
2021-10-15 20:12 ` Michael Nazzareno Trimarchi
2021-10-18 7:19 ` Miquel Raynal
2021-10-18 7:33 ` Michael Nazzareno Trimarchi
2021-10-18 7:43 ` Miquel Raynal
2021-10-04 5:54 ` Christian Eggers
2021-10-04 6:27 ` Michael Nazzareno Trimarchi
2021-10-04 15:33 ` Miquel Raynal
2021-10-04 16:06 ` Han Xu
2021-10-05 6:02 ` Christian Eggers
2021-10-08 9:55 ` Christian Eggers
2021-10-08 12:08 ` Stefan Riedmüller
2021-10-08 12:27 ` Miquel Raynal
2021-10-08 13:11 ` Christian Eggers
2021-10-08 13:29 ` Miquel Raynal
2021-10-08 13:36 ` Miquel Raynal
2021-10-08 13:49 ` Christian Eggers
2021-10-08 16:07 ` Miquel Raynal
2021-10-09 5:53 ` Michael Nazzareno Trimarchi
2021-10-11 6:46 ` Miquel Raynal
2021-10-12 9:02 ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Stefan Riedmueller
2021-10-12 9:02 ` [RFC PATCH 2/2] gpmi-nand: Add ERR007117 protection for nfc_apply_timings Stefan Riedmueller
2021-10-13 5:01 ` Han Xu
2021-10-22 8:45 ` Stefan Riedmüller
2021-10-22 14:35 ` han.xu
2021-10-25 9:39 ` Stefan Riedmüller
2021-10-28 9:28 ` Stefan Riedmüller
2021-11-01 4:01 ` han.xu
2021-10-13 6:10 ` Christian Eggers
2021-10-13 6:00 ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Christian Eggers
2021-10-09 6:26 ` GPMI iMX6ull timeout on DMA Christian Eggers
2021-10-13 6:15 ` Christian Eggers
2021-10-08 13:13 ` Christian Eggers
2021-10-08 13:30 ` Miquel Raynal
2021-10-09 6:33 ` Christian Eggers
-- strict thread matches above, loose matches on Subject: below --
2018-10-02 13:22 GPMI IMX6ull timeout on dma Michael Nazzareno Trimarchi
2018-10-04 14:36 ` Michael Nazzareno Trimarchi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ec14d017-1274-c7ea-f0b2-6c20dc07360e@kernel.org \
--to=gerg@kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=michael@amarulasolutions.com \
--cc=miquel.raynal@bootlin.com \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).